Mazda 2009 Tribute manual

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 16 Entertainment Systems 19 AM/FM stereo with CD/MP3 19 Auxiliary input jack (Line in) 27 USB port 29 Satellite radio information 32 Climate Controls 36 Manual heating and air conditioning 36 Rear window defroster 38 Lights 39 Headlamps 39 T urn signal control 42 Bulb replace[...]

Seating and Safety Restraints 82 Seating 82 Safety restraints 93 Airbags 108 Child restraints 124 Tires, Wheels and Loading 141 T ire information 143 T ire inflation 145 T ire Pressure Monitoring System (TPMS) 159 V ehicle loading 164 T railer towing 171 Recreational towing 176 Driving 178 Starting 178 Brakes 184 Electronic stability control 187 T [...]

Maintenance and Specifications 253 Engine compartment 261 Engine oil 265 Battery 269 Engine coolant 271 Fuel information 277 Air filter(s) 291 Maintenance product specifications and capacities 293 Engine data 295 Accessories 298 Index 299 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or b[...]

CONGRATULATIONS Congratulations on acquiring your new Mazda product. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Mazda and its products visit the following webs[...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. SPECIAL NOTICES Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic informat[...]

Emission warranty The New V ehicle Limited W arranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties. For a detailed description of what is covered and what is not covered, refer to the W arranty Guide that is provi[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Manual Protecting the Environment Fasten Seat Belt Airbag - Front Airbag - Side Passenger Airbag Off Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Ba[...]

V ehicle Symbol Glossary Power W indow Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Service Engine Soon Engine Air Filter Speed Control Passen[...]

Multi-function lever (pg. 49) Instrument cluster (pg. 12) Hazard flasher control (pg. 207) Headlamp control (pg. 39) Parking brake release (pg. 186) Speed controls* (pg. 57) Hood release (pg. 260) * if equipped 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Instrument Cluster 10[...]

Climate controls (pg. 36) Audio system (pg. 19) Auxiliary input jack (pg. 27) Electronic stability control (pg. 187) Auxiliary power point (pg. 53) USB port* (pg. 29) *if equipped 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Instrument Cluster 11[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains [...]

W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap fill inlet: Illuminates when the fuel cap fill inlet may not be properly closed. Continued driving with this light on may caus[...]

W ARNING: If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately by an authorized Mazda dealer . W ith the ABS light on, the anti-lock brake system is disabled but normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released. Airbag readin[...]

Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating your tires in the T ires, Wheels and Loading chapter . When the ignition is first turned to on, the light will illuminate for three seconds to ensure the bulb is workin[...]

Door ajar: Illuminates when the ignition is in the on position and any door is open. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators flash faster , check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds [...]

Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine a[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on[...]

AUDIO SYSTEMS AM/FM/single CD or in-dash CD6/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Mazda strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe[...]

AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off. T urn the knob to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition is turned back on. AM/FM: Press repeatedly to select AM/FM1/FM2 frequency band. TUNE: T [...]

T o activate the autoset feature: Press MENU repeatedly until AUTO PRESET ON/OFF appears in the display . Use SEEK/TRACK to toggle AUTO PRESET to ON, and either wait five seconds for the search to initiate or press OK to immediately initiate the search. If you press another control within those five seconds, the search will not initiate; the 10 str[...]

T o auto load up to six discs– Press and hold LOAD until the display reads AUTOLOAD #. Load the desired disc, label side up. The system will prompt you to load discs for the remaining available slots. Insert the discs, one at a time, label side up, when prompted. Once loaded, the disc in preset #1 will begin to play . Press the number preset butt[...]

In MP3 folder mode– Press DIRECT and the memory preset buttons (0–9) of the desired folder . The system will advance to that specific folder . TEXT : In MP3 mode only– Press TEXT repeatedly to view Album (AL), Folder (FL), Song (SO) and Artist (AR) in the display , if available. In TEXT MODE– Sometimes the display requires additional text t[...]

DIRECT : Press DIRECT then enter the desired channel (i.e. 002) using the memory preset buttons (0–9). If you only enter one digit, press OK and the system will go to that satellite channel. If you enter three digits, the system will automatically go to that channel, if available. Y ou may cancel your entry by pressing DIRECT . If an invalid stat[...]

SA TELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu. Press / to cycle through the following options: • CA TEGOR Y : Press OK to enter category mode. Press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press OK when the desire[...]

SONG ALERTS ENABLED/DISABLED will appear in the display . The menu listing will display the opposite state. For example, if you have chosen to enable the song alerts, the menu listing will read DISABLE as the alerts are currently on, so your other option is to turn them off. Sound Adjustments Press SOUND repeatedly to cycle through the following fe[...]

TUNE/OK: Y our vehicle may be equipped with features which will require you to confirm commands by pressing OK. Auxiliary input jack (Line in) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Mazda strongly recommends that drivers use extreme caution when using any device that may take their focus off [...]

Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm) connectors at each end T o play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music pla[...]

5. For safety reasons, connecting or adjusting the settings on your portable music player should not be attempted while the vehicle is moving. Also, the portable music player should be stored in a secure location, such as the center console or the glove box, when the vehicle is in motion. The audio extension cable must be long enough to allow the p[...]

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect ra[...]

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached. CDs with homemade paper (a[...]

• MP3 folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001 (folder) T001 (track) to F253 T255. • Creating discs with only one level of folders will help with navigation through the disc fil[...]

Satellite radio reception factors: T o receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on the roof of your vehicle. The vehicle roof provides the best location for an unobstructed, open view of the sky , a requirement of a satellite radio system. Like AM/FM, there are several factors that can affe[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of sign[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: T urn to select fan speed. 2. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be [...]

10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter . 11. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed to cool down the interior of the vehicle a[...]

During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the A/C in the MAX A/C position, reduce blower fan speed from the highest setting and put the vehicle’ s transmission into the P ARK gear position (automatic transmission only) to continue to receive cool air from your A[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Fog lamp control (if equipped) The headlamp control also operates the fog lamps. The fog lamps can be turned on when the headlamp control is in the , or po[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output. T o activate: • the ignition must be in the on position. • the headlamp control must be in the off, parking lamps or autolamp position. • with automatic transmission, th[...]

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full Dome/ON position to reset. This will ensure that your displays are visible under all lighting conditions. AIMING THE HEADLAMPS The headlamps on your vehicle are p[...]

4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted. 5. Locate the vertical adjuster on the headlamp, then us ea4m m socket to turn the adjuster either counterclockwise (to adjust u[...]

INTERIOR LAMPS Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate when the doors are open or when attempting to turn the dome lamp on by fully rotating the dimmer control located on the instrument [...]

Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. When the control is in the OFF position, it will not illuminate when you open the doors. BULB REPLACEMENT Headlamp condensation Exteri[...]

Function Number of bulbs T rade number Headlamps (high and low beams) 2 H13 Park/turn/sidemarker lamps (front) 2 3157A (amber) Rear stop/tail/sidemarker 2 3157K / 4157K Backup lamp 2 921 Fog lamp (front) 2 9145 Center High-mount stop lamp 5 W5WL Rear license plate lamp 2 168 All replacement bulbs are clear in color except where noted. T o replace a[...]

W ARNING: Handling Halogen Bulbs: When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass. If the glass portion of the bulb is touched with bare hands, body oil could cause the bulb to overheat and explode when lit. Never touch the g[...]

1. Make sure the headlamp switch is in the off position and then open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly . 3. Carefully remove the lamp assembly away from the vehicle by pulling the assembly straight out to expose the bulb socket. DO NOT TIP THE LAMP ASSEMBL Y SIDEW A YS. 4. Rotate the b[...]

Replacing high-mount brake lamp bulbs T o remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in rev[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Note: Heavy ice and snow can jam the wiper blades and overheat the wiper motor . If this happens, the motor will automatically stop the operation of the blades for a short p[...]

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — Normal speed operation of rear wiper . INT 1 — Intermittent operation of rear wiper . OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer cont[...]

W ARNING: Adjusting the steering wheel while the vehicle is moving is dangerous. Moving it can very easily cause the driver to abruptly turn to the left or right. This can lead to loss of control or an accident. Never adjust the steering wheel while the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the v[...]

CENTER CONSOLE Y our vehicle is equipped with a variety of console features. These include: 1. Cupholders 2. Utility compartment console lid has a CD holder , a business card holder and two pen holders. The utility compartment has a removable bin with coin holder slots, a sliding tray , a cell phone holder and CD holders 3. Rear power point 4. Rear[...]

The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage. AUXILIARY POWER POINT (12VDC) W ARNING: Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket [...]

Always keep the power point caps closed when not being used. Cigarette/Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when [...]

One touch down (AUTO) Allows the driver’ s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation. Window lock The window lock feature allows only the driver to operate t[...]

EXTERIOR MIRRORS Power side view mirrors W ARNING: Do not adjust the mirror while the vehicle is in motion. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center[...]

CRUISE CONTROL/SPEED CONTROL (IF EQUIPPED) W ith cruise control/speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal. W ARNING: Using cruise control in the following conditions could cause you to lose control of the vehicle: • Heavy or unsteady traffic • Slippery or winding roads • Similar restric[...]

• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Disengaging speed control T o disengage the speed control: • T ap the brake pedal or clutch pedal (if equipped) Disengaging the speed control will not erase previous set speed. Note: When you use the clutch pedal to [...]

Reducing speed while using speed control There are three ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. • Press and release the SET - control to operate the T ap-Down function. Each tap will decrease the set speed by 1 mph (1.6 km/h). • Depress the brake pedal or th[...]

W ARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. T o open the moon roof: The moon roof is equipped with an automatic, one-touch, opening, closing and venting feature. Press and release the rear portion of the control. T o stop motion at any time during the one-tou[...]

T o vent: • The moon roof is equipped with an automatic, one-touch, vent feature. T o tilt the moon roof into the vent position (when the glass panel is closed), press and release the front portion of the control. • T o close the moon roof from the vent position, press and hold the rear portion of the control until the glass panel stops moving.[...]

W ARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. Exhaust fumes contain carbon monoxide which can injure your lungs and cause drowsiness and even death. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, [...]

Cargo management system (if equipped) The cargo management system consists of two storage compartments located in the floor of the rear cargo area. 1. The larger , rearward, compartment is for customer storage. • T o open, lift the lid with the pull latch. The lid can be removed to allow for flexible storage. • T o close, lower the lid and pres[...]

LUGGAGE RACK (IF EQUIPPED) Y our vehicle may be equipped with a roof rack. The maximum load for the roof rack is 100 lb (45 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars as possible. Do not use the vehicle’ s door handles as tie down lo[...]

T o remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross-bar assembly off th[...]

T o reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 3. Slide the cross-bar assemblies over the end cap t[...]

KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose y[...]

Recommended handling of the Integrated Keyhead T ransmitter (IKT) T o avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead T ransmitter (IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into the ignition cylinder , place your thumb on the [...]

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors T urn the key in the door cylinder to unlock the driver’ s door only . All other doors will remain locked. Locking the doors T urn the key in the door cylinder to lock the driver’ s door only . Auto[...]

Power door unlock/lock procedure Y ou must complete Steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. Note: All doors must be closed and remain closed throughout the configuration process. 1. The ignition must be off to begin sequence. 2. T urn the ignition to the[...]

Deactivating/activating autounlock Y our vehicle comes with the autounlock feature activated. There are two methods to enable/disable this feature: • Through your authorized dealer , or • by using the power door unlock/lock sequence. Note : The autounlock feature can be activated/deactivated independently of the autolock feature. Power door loc[...]

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . NOTE: Setting the lock for one door will not automatically set the lock[...]

The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate glass. • activate the personal alarm. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position. The [...]

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once. 2. Press and release again within three seconds to confirm that all the doors and liftgate are closed and locked. Note: The doors will lock again and the horn will chirp once. If any of [...]

T o replace the battery: 1. T wist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover . 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new[...]

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead T ransmitter or the keyless entry system keypad is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the on position, or • the Integrated Keyhead T ransmitter lock co[...]

1. The ignition must be off to begin the sequence. 2. Place the key in the ignition and turn the ignition to the 3 (on) position. 3. Press the power door unlock control on the door panel three times. 4. T urn the ignition from the 3 (on) position to the 1 (off) position. 5. Press the power door unlock control on the door panel three times. 6. T urn[...]

Y our vehicle comes with two coded Integrated Keyhead T ransmitters; additional coded IKT s may be purchased from your authorized dealer . Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. The authorized dealer can program your spare IKT s to your vehicle or you [...]

Automatic arming The vehicle is armed immediately after switching the ignition to the off position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the on position. The theft indicator will illuminate for t[...]

T ips: • Only use Integrated Keyhead T ransmitters (IKT s) or standard SecuriLock™ keys. • Y ou must have two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible. • If two previously programmed coded keys are not available, you must take your vehicle to you[...]

If the key has been successfully programmed it will start the vehicle’ s engine and will operate the remote entry system (if the new key is an Integrated Keyhead T ransmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming. If the key was not successfully programmed, it will not sta[...]

SEA TING Adjustable head restraints Y our vehicle is equipped with front row outboard head restraints that are vertically adjustable. W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The [...]

3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust th[...]

2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. Properly adjust the head restraint so that the top of [...]

W ARNING: Not securing luggage or cargo while driving is dangerous as it could move or be crushed during sudden braking or a collision and cause injury . Make sure luggage and cargo are secured before driving. W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across t[...]

Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’ s seatback. T urn the lumbar support control clockwise to increase firmness. T urn the lumbar support control counterclockwise to increase softness. Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver?[...]

W ARNING: T o reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or ?[...]

Heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater . The seat heater may cause burns even at low temperatures, especially if used [...]

The head restraints can be moved up and down. Push control to lower head restraint. Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Seating and Safety Restraints 89[...]

3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the seat belt web snap button to the quarter trim panel snap button. This will assure that seatbelt does not get caught by staying out of the seat back folding path. 2009 Tribute (j14) Owners Guide, 1st Printing [...]

5. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat. NOTE: When the seatback release lever is pulled, slowly lower seatback to the flat position. 6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatbac[...]

2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and the RED seat unlatched indicator on release paddle is not visible. W ARNING: Make sure seat belt buckle heads are through elastic holders on seat backs. Seat belt buckle heads may break if they are trapped underneath the seatback as the [...]

T o remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. Pull the cushion to the outboard side of the vehicle. T o install the rear cushion 1. Insert rod ends into floor mounting points and push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety S[...]

• Front crash severity sensor . • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), seat belt pretensioners, front seat belt usage sensors, driver seat position sensor , front passenger sensing system, and indicator lig[...]

Driver ’s seat position sensor The driver’ s seat position sensor allows your Personal Safety System 威 to tailor the deployment level of the driver dual-stage airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensin[...]

Front seat belt usage sensors The front seat belt usage sensors detect whether or not the driver and front outboard passenger seat belts are fastened. This information allows your Personal Safety System 威 to tailor the airbag deployment and seat belt pretensioner activation depending upon seat belt usage. Refer to Safety restraints section in thi[...]

If any of these things happen, even intermittently , have the Personal Safety System 威 serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the h[...]

W ARNING: Placing a child, 12 years or younger , in the front seat is dangerous. The child could be hit by a deploying airbag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side airbag (if equipped) in a moderate collision. Whenever possible, always secure a child, 12 years or you[...]

• This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner . This feature is designed to help reduce the belt force acting on the occupant’ s chest. All seat belts in the vehicle are combination lap and shoulder belts. The passenger seat belts have two types of locking modes described below: V eh[...]

• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract[...]

Seat belt height adjustment Y our vehicle has seat belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down. Release the buttons [...]

W ARNING: Failure to replace both front restraints under the above conditions could result in severe personal injuries in the event of a collision. The seat belt pretensioners will only function once. After they are deployed, they will not work again and must be replaced immediately , even if there was no front seat occupant seated at the time. W A[...]

Conditions of operation If... Then... The driver’ s seat belt is not buckled before the ignition switch is turned to the on position... The seat belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s seat belt is buckled while the indicator light is illuminated and the warning chime is sounding... The[...]

If... Then... The driver’ s and front passenger’ s seat belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s seat belt is not buckled when the vehicl[...]

The following are reasons most often given for not wearing seat belts (All statistics based on U.S. data): Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36,700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during [...]

Reasons given... Consider ... ⬙ I have an airbag ⬙ Airbags offer greater protection when used with seat belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. ⬙ I’d rather be thrown clear ⬙ Not a good idea. People who are ejected are 40 times more likely to DIE. Seat belts help prevent ejection, WE CAN?[...]

• The driver and front passenger seat belts are unbuckled W ARNING: While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the Belt-Minder 威 system activated for yourself and others who may use the vehicle. T o red[...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the seat belt to help protect the driver and right front passenger from certain upper body injuries. W ARNING: Airbags DO NOT inflate slowly or gently and the risk of injury from a deployin[...]

W ARNING: The driver should always hold onto only the rim of the steering wheel. Never place your arm over the airbag module or anywhere inside the rim as a deploying airbag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can w[...]

Children and airbags For additional important safety information, read all information on safety restraints in this guide. W ARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions rather than in the front seating position. Failure to follow thes[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serio[...]

• and the electrical wiring which connects the components. • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter . • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter . • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger [...]

For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and seat belt is unbuckled. The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passenger[...]

• Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat, and the system should be taken promptly to an authoriz[...]

The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below . Objects Pass Airba[...]

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If ob[...]

A malfunction with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beep sounds will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired.[...]

How does the side airbag system (if equipped) work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployme[...]

The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision caus[...]

Side-curtain airbag system (if equipped) Y ou can easily confirm if your vehicle has side-curtain airbags by looking inside the vehicle up at the upper ⬙ B ⬙ pillar where you will see an embossed ⬙ AIRBAG ⬙ label. W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a dep[...]

How do the side-curtain airbags (if equipped) work? The design and development of the side air curtain system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the dep[...]

The side-curtain airbags are mounted to roof side-rail sheet metal, behind the headliner , above the first and second row seats. In certain lateral collisions or rollover events, the side-curtain airbags will be activated, regardless of which seats are occupied. In certain rollover events, the side-curtain airbag (if equipped) on both sides of the [...]

Determining if the side-curtain airbags are operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument cluster chapter . Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of t[...]

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device [...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.45 meters) tall, are greater than age four (4) and less than age twelve (12), and between[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Seat belt and top tether anchor Seat belt and LA TCH (lower anchors and top tether anchor) Seat belt only Rear facing child [...]

W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collisio[...]

If the child is the proper height, age, and weight (as specified by your child safety seat or booster manufacturer), fits the restraint and can be restrained properly , then restrain the child in the child safety seat or with the belt-positioning booster . Remember that child seats and belt-positioning boosters vary and may be designed to fit child[...]

Installing child safety seats with combination lap and shoulder belts The rear seat head restraints must be removed when using a child seat that utilizes the top tether anchor . Check to make sure the child seat is properly secured before each use. Children 12 and under should be properly restrained in a rear seating position whenever possible. If [...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. T ry to pull the belt out of the retractor to make sure the retract[...]

10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch (2.5 cm) of movement for proper installation. 11. Mazda recommends checking [...]

The LA TCH anchors are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. Follow the instructions on attaching child safety seats with tether straps. Refer to Attaching child safety seats with tether straps lat[...]

If you install a child seat with rigid LA TCH attachments, and have attached the top tether strap to the proper top tether anchor , do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child [...]

The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat has been installed, using either the seat belt or the lo[...]

3. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 4. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. If the sa[...]

Booster seats position a child so that vehicle lap/shoulder seat belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably at the edge of the cushion, while minimizing slouching. Booster seats may also make the shoulder belt fit better and more comfortably . T ry to keep the belt near th[...]

T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head [...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon t[...]

Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of man[...]

Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended[...]

When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or T ire Label. T o check th[...]

TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and oth[...]

W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear . However , heat caused by hot climates or frequent high loadi[...]

W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Mazda. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the T ire Label which is locat[...]

The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Mazda Motor Corporation may affect the operation of your T ire Pressure Monitoring System. If the TPMS indicator is flashing, your TPMS is malfunctioning. Y our repla[...]

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side, vibrate or shake when you’re driving, the wheels may be out of alignment. Have a qualified technician at a Mazda dealer check the wheel alignment [...]

• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Tires, Wheels and Loading 153[...]

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dis[...]

3. 65: Indicates the aspect ratio which gives the tire’ s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that rela[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ir[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The[...]

Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire Pressure W arning Lamp will turn ON if the tire pressure is significantly low . Once the light is illuminated, your tires are under inflated and [...]

When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air . It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System:[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Mazda. Use of any tire or wheel not recommended by Mazda can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death. A[...]

V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s doo[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2009 T[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus th[...]

W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations. W ARNING: Exceeding any vehicle weight rating limitation could result in [...]

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (4[...]

T RAILER TOWING T railer towing with your vehicle may require the use of a trailer tow option package. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to[...]

4x2 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb (kg) T railer W eight Range - lb (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.5L w/manual transmission 4980 (2259) 1500 (680) 24 (2.2) 2.5L w/automatic transmission 5040 (2286) 1500 (680) 24 (2.2) 3.0L w/automatic transmission 7120 (3230) 3500 (1588) 30 (2.8[...]

4x4 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb (kg) T railer W eight Range - lb (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.5L w/automatic transmission 5180 (2350) 1500 (680) 24 (2.2) 3.0L w/automatic transmission 7260 (3293) 3500 (1588) 30 (2.8) Notes: For high altitude operation, reduce GCW by 2% per [...]

Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s s[...]

• T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. For additional information, refer to Automatic [...]

Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability , emissions, reliability and causing internal transmission damage. Replace the rear axle lubricant any time the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or[...]

Four Wheel Drive (4WD) vehicles: T ow your Four Wheel Drive vehicle with all four wheels on the ground or with all four wheels off the ground using a vehicle transport trailer . Do not tow your Four Wheel Drive vehicle with the front wheels off the ground (by using a tow dolly) and the rear wheels on the ground. This will cause damage to your 4WD s[...]

STARTING Positions of the ignition 1. Off— locks the gearshift lever and steering column and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the engine is not running. 3. On— all electrical circuits operational and warning lights will illuminate. This is the position the key is in when yo[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your authorized dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the[...]

• Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3 (on) without turning the key to 4 (start). 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Driving 180[...]

Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to 3 (on) without turning the key to 4 (start). If there is difficulty in turning the key , rotate the steering wheel until the key turns freely . This [...]

Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision. W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause ca[...]

W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater , follow these recommendations for proper and safe operation: • For your safety , use an outdoor extension cord that is product certified by Underwriter’ s Laborat[...]

How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater system may consume anywhere between 400 watts or 1000 watts of energy per hour . Y our factory installed block heater system does not have [...]

The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking wit[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released. W ARNING: Always set the parking brake f[...]

ELECTRONIC STABILITY CONTROL (ESC) SYSTEM W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the the performance of the Electronic Stability Control system. In addition[...]

The Electronic Stability Control system provides the following stability enhancement features for certain driving situations: • T raction Control (TCS), which functions to help avoid drive-wheel spin and loss of traction. • Dynamic Stability Control (DSC), which functions to help avoid skids or lateral slides • Roll Stability Control™ (RSC [...]

• If the driving condition is severe and your foot is not on the brake, the brake pedal may move as the systems applies higher brake forces. Y ou may also hear a whoosh of air from under the instrument panel during this severe condition. • The brake pedal may feel stiffer than usual. T raction Control (TCS) T raction Control is a driver aid fea[...]

Certain adverse driving maneuvers may activate the Dynamic Stability Control system, which include but are not limited to: • T aking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Driving over a patch of ice or other slippery surfaces • Changing lanes on a snow-rutted road • Entering a snow-free road [...]

Stability Control system can be restored by pressing the Electronic Stability Control ⬙ Off ⬙ button again or by turning off and restarting the engine. If you switch off the Electronic Stability Control system, the sliding car ⬙ icon will illuminate steadily . Pressing the Electronic Stability Control ⬙ Off ⬙ button again will turn off th[...]

During T railer Sway Control events the icon in the instrument cluster will flash momentarily . In some cases when trailer sway is detected, the vehicle speed is too high and may be at or above a speed at which trailer sway will grow continuously . This may cause the system to activate multiple times, causing a gradual reduction in speed. Disabling[...]

PREPARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher cente[...]

If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter . If the fuse is not blown, perform the following procedure: 1. Apply th[...]

Automatic T ransmission Adaptive Learning Y our transmission is equipped with an adaptive learning strategy found in the vehicle computer . This feature is designed to increase durability and provide consistent shift feel over the life of the vehicle. A new vehicle or transmission may have firm and/or soft shifts. This operation is considered norma[...]

W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).[...]

• The over drive cancel and grade assist lamp in the instrument cluster is illuminated. 2. Grade Assist • Improves driving experience in hilly terrain or mountainous areas by providing additional grade (engine) braking and extends lower gear operation on uphill climbs. • Provides additional engine braking through the automatic transmission sh[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral posi[...]

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 1-2 10 mph (16 km/h) 2-3 20 mph (32 km/h) 3-4 32 mph (52 km/h) 4-5 37 mph (60 km/h) Reverse Make sure that your vehicle is at a complete stop before you shift into [...]

W ARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) W ARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . Y our vehicle is equi[...]

Basic operating principles • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water , gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, sl[...]

W ARNING: Always set the parking brake fully and make sure the gearshift is latched in 1st gear or R (Reverse) (manual transmissions) or P (Park) (automatic transmissions). T urn the ignition to the off position and remove the key whenever you leave your vehicle. W ARNING: If the parking brake is fully released, but the brake warning lamp remains i[...]

• If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. A void reducing the tire[...]

Driving through deep water may damage the transmission. If the rear axle is submerged in water , the axle lubricant should be checked and changed, if necessary . The rear axle is filled with a lubricant that does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless [...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t tu[...]

• 4WD vehicles should be driven with traction devices as referred to in Using snow tires and traction devices in the T ires, Wheels and Loading chapter . Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carryi[...]

HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Us[...]

This switch is located in the front passenger’ s footwell, behind a flip-up cover , by the kick panel access cover . T o reset the switch: 1. T urn the ignition to the off position. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition to the on position. 5. W ai[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protective Circuits 1 30A Not used (spare) 2 15A Brake On/Off switch 3 15A Not used (spare) 4 30A Moon roof 5 10A Brake Shift Interlock (BSI), SPDJB 6 20A T urn signals, Stop lamps 7 10A Low beam headlamps (left) 8 10A Low beam headlamps (right) 9 15A Interior lights 10 15A Backlig[...]

Fuse/Relay Location Fuse Amp Rating Protective Circuits 16 15A Not used (spare) 17 20A All lock motor feeds, Liftgate release, Liftglass release 18 20A Heated seat 19 25A Rear wiper 20 15A Datalink 21 15A Fog lamps 22 15A Park lamps 23 15A High beam headlamps 24 20A Horn relay 25 10A Demand lamps 26 10A Instrument panel cluster 27 20A Ignition swit[...]

Fuse/Relay Location Fuse Amp Rating Protective Circuits 43 10A Rear wiper logic, Heated seats relay , Instrument cluster 44 10A Not used (spare) 45 5A Front wiper logic, Blower motor relay 46 7.5A OCS (restraints), P ADI (restraints) 47 30A Circuit Breaker Power windows 48 — Delayed accessory relay Power distribution box The power distribution bo[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits A 80A Midi Electronic power steering module (EP AS) B 125A Midi SPDJB 1 15A* Heated mirror 2 30A** Rear defroster 3 20A** Rear power point (center console) 4 — Not used 5 10A* Powertrain Control Module (PCM) Keep Alive power , PCM relay , Canister [...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 15 — Not used 16 40A** Cooling fan 1 17 40A** Cooling fan 2 18 20A** ABS solenoid 19 30A** Power seats 20 — A/C clutch relay 21A — Rear defroster relay 21B — Fuel relay 21C — Blower relay 21D — PCM relay 22 20A* Fuel pump 23 15A* Fuel injectors 24 — Not used 25 — Not used 26 15A[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 33 — PCM diode 34 — Start diode 35 10A* Run/start, Reverse lamps, Rear defrost relay 36 — Not used 37 — Not used * Mini fuse ** Cartridge fuse CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle’ s speed. • hold th[...]

W ARNING: Refer to T ire Pressure Monitoring System (TPMS) in the T ire, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function. Dissimilar spare tire/wheel information W ARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle cont[...]

Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability 3. Full-size dissimilar spare without labe[...]

Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission) and turn engine off. Removing the jack and tools The jack and tools are located under the carpeted load floor . Pull back the carpet away[...]

Remove the lug wrench from the jack in order to remove the spare tire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through the access hole in the rear bumper . 2. T urn the handle counterclockwise and lower the spare tire until it can be slid rearward and the cable is slack. 3. Slid[...]

5. Use the lug wrench to remove the lug nut from the spare tire tether . 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached fastener strap (2) to tie the tether end to the winch actuator shaft (if equipped). Tire change procedure W ARNING: When one of the front w[...]

W ARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 1. Block the diagonally opposite wheel. 2. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raise[...]

Before placing the jack under the vehicle, NOTE the jack locations: • Front View shown from rear of front tire. Position the jack directly below the protruding bolt. 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Roadside Emergencies 222[...]

• Rear View shown from forward of rear tire. Position the jack directly below the stud on the rear trailing arm. 3. Position the jack according to the guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Be sure to place the jack away from the rear edge of the rocker to avoid damaging the rear ti[...]

Never use the differentials as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. Be sure any occupants are out of the vehicle and in a safe place. 4. Remo[...]

Stowing the jack and tools • Make sure the jack is fully lowered. • Reclip the tools onto the jack making sure that the tools are fully contained by the clips as shown. • Reinstall the jack in the pocket with the left side first, then snap the right side down. • Ensure that the hold-strap contains the jack and tools before snapping the buck[...]

carrier will ratchet when the tire is in the fully stowed position. The spare tire carrier has a built-in ratchet feature that will not allow you to overtighten. If the spare tire carrier ratchets with very little effort, take the vehicle to your authorized Mazda dealer for assistance at your earliest convenience. If your vehicle is equipped with a[...]

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger . DO NOT ap[...]

W ARNING: When the engine and radiator are hot, scalding coolant and steam may shoot out under pressure and cause serious injury . Do not remove the cooling system cap when the engine and radiator are hot. See Adding coolant in the Maintenance and Specifications section. If you find no problems, the engine is cool and no leaks are obvious, carefull[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning proce[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Roadside Emergencies 230[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’ s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. W ARNING: Do not connect the end of the second cable to the negative (-) terminal of t[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a sli[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the grou[...]

CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or [...]

4. Purchase date and current mileage 5. Y our authorized dealer’ s name and location 6. Y our question(s) If you live outside the U.S.A., please contact your nearest Mazda Distributor . STEP 3: Contact Better Business Bureau (BBB) Mazda North American Operations realizes that mutual agreement on some issues may not be possible. As a final step to[...]

In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your authorized dealer . If the cause of your dissatisfaction cannot adequately be addressed by normal authorized dealer procedures, we recommend that you take the following steps:[...]

Mediation/Arbitration Program Occasionally a customer concern cannot be resolved through Mazda’ s Customer Satisfaction Program. If after exhausting procedures in this manual, your concern is still not resolved, you have another option. Mazda Canada Inc. participates in an arbitration program administered by the Canadian Motor V ehicle Arbitratio[...]

Regional Offices Regional Offices Areas Covered Mazda Canada Inc. W estern Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Alberta, British Columbia, Manitoba, Saskatchewan, Y ukon Mazda Canada Inc. Central Region 55 V ogell Road Richmond Hill, Ontario. L4B 3K5 1 (800) 263–4680 Ontario Mazda Canada Inc. Quebec Region/A[...]

STEP 2 If, after following STEP 1, you feel the need for further assistance, please contact your area’ s Mazda representative (Indicated on the next page). Please help us by providing the following information: 1. Y our name, address, and telephone number 2. Y ear and model of vehicle 3. V ehicle Identification Number (17 digits, noted on your re[...]

California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. T wo or more repair attempts are made on the same n[...]

GUAM (d.b.a. T riple J. Enterprises, Inc.) P .O. Box 6066 T amuning, Guam TEL: (671) 646–9216 SAIP AN Pacific International Marianas, Inc. (d.b.a. Midway Motors) P .O. Box 887 Saipan, MP 96950 TEL: (670) 234–7524 T riple J Saipan, Inc. (d.b.a. T riple J Motors) Beach Road Chalan LauLau Saipan, MP 96950 TEL: (670) 235–4868 AMERICAN SAMOA Polyn[...]

The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries. W e strongly recommend that you NOT take your Mazda outside the United States. However , in the event that you are moving to Canada permanently , Mazda vehicles built for use in the United States could be eligible for expo[...]

ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’ s performance or safety system; the manufact[...]

WORKSHOP MANUAL: Covers recommended maintenance and repair procedures of the drive train, body and chassis. WIRING DIAGRAM: Provides electrical schematics as well as component location for the entire electrical system. OWNER’S MANUAL: This booklet contains information regarding the proper care and operation of your vehicle. This is not a technici[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlig[...]

PAINT CHIPS Y our dealer has touch-up paint to match your vehicle’ s color . T ouch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the [...]

• 2.5L DOHC I4 Engine • 3.0L DOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use cool or lukewarm water wi[...]

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellant coatings, tree sap, or other organic con[...]

INTERIOR For fabric, carpets, cloth seats, seat belts and seats equipped with side air bags (if equipped): • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Upholstery Cleaner and Spot Remover (0000–77–430E-01), available at your authorized Mazda dealer . • If grease or tar is present on the material[...]

UNDERBODY Flush the complete underside of your vehicle frequently . Keep body and door drain holes free from packed dirt. MAZDA CAR CARE PRODUCTS Y our Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are c[...]

INTRODUCTION Be extremely careful to prevent injury to yourself and others or damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an authorized Mazda Dealer . Factory-trained [...]

SCHEDULE 1 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Miles 7.5 15 22.5 30 37.5 45 52.5 [...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Miles 7.5 15 22.5 30 37.5 45 52.5 60 67.6 75 82.5 90 (x 1000 Km) (12) (24) (36) (48) (60) (72) (84) (96) (108) (120) (132) (144) CHASSIS and BODY Brake lines, hoses and connections II I Disc brakes I I I I I[...]

SCHEDULE 2 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 [...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60 (x 1000 Km) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) COOLING SYSTEM Cooling system and hoses I I Engine coolant (yellow) Replace at first 100,000 mil[...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60 (x 1000 Km) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) Exhaust system heat shields I I All locks and hinges LLLLLLLLLLLL W asher fluid level IIIIIIIIII[...]

Retightening lug nuts • Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). • Refer to Wheel Lug Nut T orque Specification in the T ires, Wheels and Loading chapter for the proper lug nut torque specification. SERVICE RECOMMENDATIONS T o hel[...]

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First). 2. T urn off the engine and remove the key . 3. Block the wheels. Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, d[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.5L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine coolant bleed valve 9. Engine oil dipstick 10. W indshield washer fluid reservoir [...]

3.0L DOHC V6 engine 1. Engine coolant reservoir 2. Air filter assembly 3. Brake fluid reservoir 4. Automatic transmission fluid dipstick 5. Power distribution box 6. Battery 7. Coolant bleed valve 8. Engine oil dipstick 9. Engine oil filler cap 10. W indshield washer fluid reservoir 2009 Tribute (j14) Owners Guide, 1st Printing USA (fus) Maintenanc[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Mazda specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and sme[...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimu[...]

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. T o replace the wiper blade: 1. Grab the wiper arm with one hand close to the arm/blade joint and pull it as far away from the glass as possible. Do not use excessive force because it can[...]

• 2.5L I4 engine • 3.0L DOHC V6 Duratec engine 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within the lower and upper holes or lower and upper lines, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole or the lower line, engine oil must be added to [...]

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above the upper hole or upper line may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the dipstic[...]

Engine oil and filter recommendations SAE 5W -20 engine oil is recommended Look for this certification trademark. Use SAE 5W -20 motor oil certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements o[...]

BATTERY Y our vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, ma[...]

W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medi[...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the“FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance section for service interval schedules. • Be sure to read and [...]

• The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’ s engine cooling system. If you are unsure which type of coolant your vehicle requires, contact your local authorized dealer . W ARNING: Do not put engine coolant in the windshield washer fluid reservoir . If engine coolant [...]

Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins[...]

Recycled engine coolant Not all coolant recycling processes produce coolant which meets Mazda recommended coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner . Follow your community’ s regulatio[...]

• Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. What you [...]

2. Arrange for the vehicle to be taken to an authorized dealer . 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low . W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to an authorized dealer . Driving[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. If the Check Fuel Fill Inlet lamp or Check Fuel Fill Inlet message comes on, the fuel fill inlet may[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” in high altitude areas that are sold with octane ratings less than 87. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally , adding 1 gallon (3.8L) of fuel is enough to restart the engine. If the vehicl[...]

2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel. Do not use aftermarket funnels; they will not work with the Easy Fuel?[...]

For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling.[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat te[...]

W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the Service engine soon indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of e[...]

These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the Service engine soon indicator should stay off the next time the engine is started. A d[...]

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, the above driv[...]

4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remov[...]

Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary , add fluid in 1/2 pint (250 mL) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift [...]

W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Release the clamps that secure the air filter housing cover . • 2.5L • 3.0L 2. Pull the air filter housing cover away . 3. Remove the air filter element from the[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Application Mazda part name or equivalent Capacity Brake fluid and (clutch fluid–if equipped) All High Performance DOT 3 Motor V ehicle Brake Fluid Between MIN and MAX on reservoir Engine coolant 2.5L engine Mazda yellow-colored Premium Engine Coolant 1 7.4 quarts (7.0L) 3.0L engine 9.5 quart[...]

Item Application Mazda part name or equivalent Capacity Fuel tank All — 16.5 gallons (62.5L) 1 Add the coolant type originally equipped in your vehicle. Do not mix different colors or types of coolant. Do not use Mazda Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant in this chapter . 2 Service refill capacity is det[...]

ENGINE SPECIFICA TIONS Engine 2.5L I4 engine 3.0L DOHC V6 engine Cubic inches 152 183 Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system Coil on plug Coil on plug Spark plug gap 0.049–0.053 inch (1.25–1.35mm) 0.045–0.049 inch (1.15–1.25mm) Compression ratio 9.7:1 10.3:1 Engine drivebelt routing • 2.5L I4 En[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION CODE DESIGNATIONS Y ou [...]

CELL PHONES Use of cell phones and other devices by driver: W ARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’ s hands. Use of these devices will [...]

A ABS (see Brakes) ..................... 184 Accessory delay .......................... 55 Air cleaner filter ............... 291, 293 Air conditioning manual heating and air conditioning system ................. 36 Airbag supplemental restraint system ........................ 108, 117, 120 and child safety seats ............110 description .......[...]

Cleaning your vehicle engine compartment .............. 248 instrument panel .................... 250 interior ..................................... 251 Mazda car care products ....... 252 plastic parts ............................ 249 washing .................................... 247 waxing ..................................... 247 wheels .........[...]

Four -Wheel Drive vehicles driving off road .......................200 preparing to drive your vehicle ..................................... 193 Fuel ............................................ 277 calculating fuel economy ....... 283 cap ........................................... 279 capacity ................................... 293 choosing the [...]

cargo lamps ............................... 40 daytime running light ...............40 fog lamps ................................... 39 headlamps ................................. 39 headlamps, flash to pass ..........40 instrument panel, dimming ..... 40 interior lamps ..................... 43–45 replacing bulbs ......................... 45 LA T[...]

Roof rack ..................................... 64 S Safety defects, reporting .......... 246 Safety restraints ............ 93, 97–101 Belt-Minder 威 ........................... 103 extension assembly ................ 102 for adults ........................... 98–100 for children ............................. 124 Occupant Classification Senso[...]

T ransmission automatic operation ............... 193 brake-shift interlock (BSI) .... 193 fluid, checking and adding (automatic) ............................. 289 fluid, checking and adding (manual) ......................... 289, 291 fluid, refill capacities ..............293 lubricant specifications .......... 293 manual operation ...............[...]