Miele G 5935 SCi XXL manual

Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. M.-Nr. 09 191 340 en - AU, NZ[...]

Description of the appliance .........................................5 Appliance overview .................................................5 Control panel ......................................................6 Warning and Safety instructions .....................................7 Caring for the environment ........................................[...]

Cutlery ..........................................................3 9 3D cutlery tray (depending on model) ...............................3 9 Cutlery basket (depending on model) ...............................4 0 Operation .......................................................4 1 Detergent ........................................................4 [...]

Comparison tests .................................................7 0 Programme chart .................................................7 2 After sales service ................................................7 8 Repairs .......................................................7 8 Future updates .................................................7 8 Opti[...]

Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combination h Data plate i Child safety lock in door grip (not visible) j Rinse aid reservoir k Dual compartment detergent dispenser l Salt reservoir Descript[...]

Control panel a Miele < home The appliance is compatible with the Miele | home system (available in selected countries) b Selector sensors For selecting the option displayed next to them. For altering the values displayed (+/-). For navigating to further screens. The selector sensors light up when active. c On/Off sensor K For switching the appl[...]

This appliance complies with all relevant statutory safety requirements. Improper use of the appliance can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installing and using it for the first time. They contain importan[...]

Safety with children ~ Young children must not be allowed to use this appliance. ~ Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse. ~ Cleaning may only be carried out by older children under the supervision of an adult. ~ Children s[...]

Technical safety ~ Before installation, check the dishwasher for visible signs of damage. Under no circumstances should you use a damaged dishwasher. A damaged dishwasher could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket. The electrical socket must be easily accessible after the dis[...]

~ Before connecting the appliance, check that the connection data on the data plate (voltage and rated load) match the mains electricity supply. If in any doubt, consult a qualified electrician. ~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system. It is most import[...]

~ The plastic housing of the water connection contains an electrical valve. The housing must not be dipped in water. ~ There are live wires in the water inlet hose. Never cut the water inlet hose, even if it is too long. ~ The integrated Waterproof System offers protection from water damage, provided the following conditions are met: – The dishwa[...]

~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. ~ Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replace[...]

Correct installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ Be careful when installing the dishwasher. Wear protective gloves to avoid injury on any sharp metal components. ~ The dishwasher must be correctly aligned to ensure problem-free operation. ~ In order to ensure stability, built-[...]

Correct use ~ Do not use solvents in the dishwasher. Danger of explosion! ~ Avoid inhalation of powder detergents. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. ~ Avoid [...]

~ Do not fill the rinse aid reservoir with powder or liquid detergent. This will cause serious damage to the reservoir. ~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. ~ Miele recommends using specially designed dishwasher salt to maximize the performance of your dishwasher and t[...]

Accessories ~ Only use genuine Miele spare parts and accessories with this dishwasher. If spare parts or accessories from other manufacturers are used, this will invalidate the warranty, and Miele cannot accept liability. Disposal of your old dishwasher ~ Make the door lock inoperative so that children cannot accidentally shut themselves in. Remove[...]

Disposal of the packing material The packing material protects the dryer from transport damage. The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. The packaging consists of the following materials: Outer packaging: – Corrugated cardboard made from up [...]

Energy saving dishwashing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies. If the water is heated by solar panels, for example, t[...]

To open the door At the end of the programmes with a drying phase (see Programme chart) the door will open automatically a little in order to help the drying process. This function can be deactivated (see Settings menu - AutoOpen). ^ Reach under the handle and pull the door open. If the door is opened during operation, all functions are automatical[...]

Display The display is used to select the following: – the programme – Extra options – the Delay start time – the Settings ! menu – information During a programme, the display shows the following: – the name of the programme – the current time of day – the stage the programme is at – the estimated time left for the programme to ru[...]

Basic settings Welcome screen ^ Switch the dishwasher on using the K sensor. If the dishwasher is being switched on for the first time, the welcome screen will appear after a few seconds. Language The display will then change automatically to the screen for setting the language. Language F [ [ [ $ ceština # dansk p ! deutsch OK ! ^ Select th[...]

Time of day The display will then change to the screen for setting the time. Time [ [ [ + $ 10 :21 - # OK ! ^ Set the hours with the +/- sensors and confirm with OK . Then set the minutes, and confirm with OK . Display The display will then change to the screen for setting the display for the time of day. Time [ $ Do not display ( # On ! On f[...]

– The dishwasher must be programmed for the water hardness in your area. – Where the water hardness fluctuates e.g. between 1.4 - 3.1 mmol/l (8 - 17 °d German scale), always programme the dishwasher to the higher value (3.1 mmol/l in this example). – Your local water authority will be able to advise you of the water hardness level in your ar[...]

Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened. This takes place automatically in the integrated [...]

Programming the water hardness level ^ Switch the dishwasher on with the On sensor K if it is switched off. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see "Settings ! menu - Memory"). If this is the case, press the U sensor to[...]

Before using the appliance for the first time, you require: – approx. 1 kg of dishwasher salt, – domestic dishwasher detergent, – rinse aid formulated for domestic dishwashers. Every dishwasher is tested at the factory. There will be residual water in the appliance from this test. It is not an indication that it has been used previously. Fill[...]

^ When filling the salt reservoir, only open the door halfway to ensure that all the salt gets into the reservoir. ^ Press the button on the lid of the rinse aid reservoir in the direction of the arrow until the flap springs open. ^ Lift up the funnel. Do not fill the reservoir with water. ^ Add salt only until the reservoir is full or until water [...]

Salt indicator ^ Fill the salt reservoir with dishwasher salt for reactivation when the F Insufficient salt message appears. (If it appears during a programme, wait until the end of the programme). ^ Confirm with OK . The "Insufficient salt" message will go out. After the salt reservoir has been filled, the "Insufficient salt" m[...]

Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically. , Inadvertently filling the rinse aid reservoir with powder or liquid detergent will[...]

^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid. This prevents over-foaming occurring during the next programme. You can adjust the rinse a[...]

Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. These materials will cause damage to the dishwasher. Crockery can be loaded anywhere in the baskets, but the following notes should be observed: – Do no[...]

Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher. – Craft items, antiques, valuable vases and decorative glassware are also not suitable for dishwash[...]

Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running Tall items 65 °C programme, if available). ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the[...]

Jumbo cup rack (depending on model) The cup rack can be set at two different widths so that it can also accommodate large cups. ^ Pull the cup rack upwards and click it back into position at the required width. Glass rail This rail is designed to hold glasses with long stems securely. ^ Lower the rail and lean tall glasses against it. ^ You can als[...]

Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. This can be useful to help prevent water being left in deep dishes [...]

Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. You can also place glasses, cups, small plates and saucers in the lower basket. Do not place thin, delicate glassware in the lower basket. Dishwashers with cutlery tray Heavily soiled items ^ Place large platters and dishes in the centre of the lowe[...]

Removable MultiComfort section The rear section of the lower basket is used for washing cups, glasses, plates, pots and pans. The MultiComfort section can be removed to make more room for larger items such as pots and pans. To remove the insert a ^ Push the yellow grip forwards and remove the insert. To replace the insert b ^ Fit the insert into th[...]

Glass rail This rail is designed to hold glasses with long stems securely. ^ Lower the rail and lean tall glasses against it. Hinged spikes The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls and saucers. Both rows of spikes in the front section of the basket can be lowered to make more room for large items, e.g[...]

Cutlery 3D cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs [...]

Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ In an appliance with a cutlery basket (depending on model) cutlery is cleaned and dried more efficiently if placed in the basket with the handles downwards. However, to avoid the risk of injury, knives, forks and other ut[...]

Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling. – Enzymes to break down starch and loosen protein. –[...]

Dispensing ^ Follow the dosage recommended by the manufacturer on the packaging. ^ Unless directed otherwise, use one detergent tab or add 20 to 30 ml to compartment II, depending on the level of soiling. With very heavy soiling you can also add a small amount of detergent to compartment l (see "Programme chart"). ^ Tabs may not dissolve [...]

Adding detergent ^ Press the opening catch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a programme. ^ Add the required amount of detergent and close the flap. ^ Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy. For information Compartment[...]

Switching on ^ Make sure the spray arms are not obstructed. ^ Close the door. ^ Turn on the tap if it is turned off. ^ Switch the dishwasher on using the K sensor. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see Settings menu ! - Memory)[...]

Selecting Extra options You can now select Extra options for your chosen programme. ^ To do this, first select Extras in the menu. The Extra options available for your programme will appear in the display. The following Extra options are available: Turbo: – For shortening the programme duration. In order to achieve optimum results, consumption ra[...]

Starting the programme ^ Select Start . The programme starts, and the prompt Add-an-item appears in the display. As long as this prompt is showing, crockery can be added without compromising the wash results. , Water in the dishwasher may be hot. Danger of scalding! Only open the door if absolutely necessary and exercise extreme caution when doing [...]

Standby To save energy, the dishwasher switches off automatically a few minutes after the last time a sensor has been pressed or at the end of a programme. ^ To switch the dishwasher back on, touch the K sensor. The Optimise standby function can be deactivated if wished (see Settings - Optimise standby). The dishwasher will then switch off after 6 [...]

Switching off At the end of a programme: ^ Switch the dishwasher off using the On/Off sensor K . The dishwasher will continue to use electricity until it is switched off with the K sensor. The dishwasher will switch off automatically after a few minutes. If the dishwasher is not going to be used for a longer period of time, e. g. whilst on holiday,[...]

Changing a programme If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: Sensor wash 12:21 [ 8 Add-an-item Time left 1:10 h Cancel ! ^ Select Cancel . ^ Confirm Cancel programme? with OK . The programme will be cancelled. Sensor wash 12:22[...]

Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A Delay start time of between 15 minutes and 24 hours can be selected. The Delay start time is set in 15-minute increments. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dr[...]

^ Select Start . Sensor wash 12:00 [ R Start at 20:00 Cancel ! The programme name and the start time will appear in the display. When the set time is reached, the programme selected will begin automatically. , To prevent children coming into contact with dishwasher detergent, do not fill the detergent dispenser until just before starting the progra[...]

BrilliantLight The dishwasher features interior lighting. The lighting will switch off automatically if the door is open for more than 15 minutes. The interior lighting can be switched off permanently. ^ Lift the half-opened door up and down quickly three times. When doing this, open the door enough so that the interior lighting switches on and off[...]

Check the condition of your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. , The outer surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces. Cleaning the wash cabinet The wash cabinet is largely self-cleaning, prov[...]

Cleaning the door front , Remove any soiling immediately. If not, it might become impossible to remove and could cause the outer surface to alter or discolour. ^ Clean the front using a sponge, a solution of warm water and a little washing-up liquid. Wipe dry using a soft cloth. For cleaning, you can also use a clean, damp microfibre cloth without [...]

Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place. Collection of coarse soil may cause the fi[...]

To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet. ^ Then turn the h[...]

Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one). ^ Push the top spray arm upwa[...]

With the aid of the following guide, minor problems can be easily corrected without contacting Miele. This will save time and money. Please note that a call-out fee will be applied for unnecessary service visits where the problem could have been rectified as described in these Operating instructions. , Installation work and repairs to electrical ap[...]

Problem Possible cause Remedy The buzzer sounds. The following fault message appears in the display: Before rectifying the problem, you must: – Open the door. – Switch the dishwasher off using the On/Off sensor K . Technical fault Fxx Call Service There may be a technical fault. After a few seconds: – Switch the dishwasher back on. – Select[...]

The dishwasher does not fill/drain. Problem Possible cause Remedy The buzzer sounds. One of the following messages appears in the display: Water inlet fault Please open the stopcock. The tap is turned off. Turn on the tap fully. Water inlet fault F12/F13 Before rectifying the problem, you must: – Switch the dishwasher off using the On/Off sensor [...]

Problem Possible cause Remedy In the display for the "Without heater" programme, the following fault message appears: Water intake temp. too low The intake water has not reached the required temperature of 45 °C (see Connection to the water supply). – Start the programme again. – If the fault message appears again, select a different[...]

General problems Problem Possible cause Remedy The display is dark. The display has switched off automatically to save energy. Switch the dishwasher on again with the On/Off sensor K . The interior lighting doesn't switch on when the door is opened. The interior lighting has been switched off permanently. Switch the interior lighting back on ([...]

Problem Possible cause Remedy Detergent residue is left in the dispenser at the end of a programme. The dispenser was still damp when detergent was added. Make sure the dispenser is dry before adding detergent. The detergent dispenser lid cannot be closed properly. Clogged detergent residue is blocking the catch. Clean the detergent from the catch.[...]

Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet. Interrupt the programme, and rearrange the items o[...]

Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme. See Programme chart. There is some stubborn soiling although most of the crockery is only lightly soile[...]

Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir is empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time - Rinse aid". Items were taken out of the cabinet too so[...]

Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glassware is not dishwasher-proof. The surfaces are affected. There is no remedy. Purchase glassware which is dishwasher-proof. [...]

Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water will flow into the wash cabinet. , The plastic housing of the water connection contains an electrical component. It must not be dipped in water. Recommendation If [...]

Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme, the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug. ^ Take the filter combination out of the was[...]

Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for energy label comparison tests: Energy Save Capacity: 15 place settings Amount of detergent: 5.0 g in compartment I, 28.7 g in compartment II Rinse aid dispensing: Setting 5 (approx. 5 ml) Upper basket level: Position: Bottom Jumbo-cup rack (if present): W[...]

Upper basket Lower basket Cutlery tray Comparison tests 71[...]

Crockery Soiling Programme Mixed, everyday crockery including pots and pans Fresh to dried on soiling Variable, sensor controlled wash Shortened cycle Glasses and plastic containers, sensitive to high temperatures Light soiling Short cycle Mixed crockery Variable, sensor controlled wash with glass care Fresh to dried on soiling Very quiet programme[...]

Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 Tab + Turbo Quick wash 40°C – 20 ml or 1 Tab 3) Sensor wash gentle – 20 ml or 1 Tab Extra quiet – 25 ml or 1 Tab 3) Light soiling 50°C – 25 ml or 1 Tab Energy save – 25 ml or 1 Tab Pot & pans 75°C 10 ml 25 ml or 1 Tab + Turbo Hygiene – 25 ml or 1 Ta[...]

Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 1x 2x Sensor wash Variable programme sequence, sensor controlled adjustment to amount of crockery and soiling If required 45-65 If required 60 X Quick wash 40 °C 40 X 45 X Sensor wash gentle # Variable programme sequence with glass care, sensor controlled adju[...]

Consumption Duration Electricity Water Cold water connection 20 °C kWh Hot water connection 55 °C kWh 1) Litres Cold water connection 20 °C h:min Hot water connection 55 °C h:min 0.80-1.25 0.55-0.90 7.0-17.0 1:30-2:38 1:18-2:21 0.55 0.20 10.0 0:38 0:27 0.75-1.00 0.45-0.55 10.0-17.0 1:26-2:02 1:17-1:43 1.05 0.75 10.0 4:45 4:35 0.78 0.35 12.3 2:3[...]

Programme When to use Pre-wash For rinsing crockery to avoid smells, if a complete cycle is not yet needed. Without heater ! Only for use with hot water connection of at least 45 °C; for lightly soiled crockery; includes sensor controlled glass care system. Intensive 65 °C For heavily soiled crockery with dried-on soiling containing starch. Pasta[...]

Programme sequence Consumption Duration Electricity Water Pre- wash Main wash °C Interim rinse Final rinse °C Drying Cold water connec - tion 20 °C kWh Hot water connec - tion 55 °C kWh 1) Litres Cold water connec - tion 20 °C h:min Hot water connec - tion 55 °C h:min X 0.01 0.01 4.0 0:15 0:15 2X X X X X 0.05 26.0 1:18 X 65 X 60 X 1.15 0.85 1[...]

Repairs In the event of any faults that you cannot remedy yourself, please contact: – Miele You will find the telephone number and address of Miele on the back cover of the manual. ^ When contacting Miele, please quote the model type and serial number of your appliance, both of which are shown on the data plate on the right-hand side of the door.[...]

To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele Chartered Agent or from Miele (some may be supplied as standard, depending on model). If you would like to … you will need to order … ... wash a Miele Cappuccinatore … a Cappuccinatore insert for the upper basket ... wash additional [...]

This dishwasher is supplied with a mains cable and moulded plug ready for connection to an AC single phase supply, (230 V 50 Hz for NZ and Australia) via a fused plug and suitable switched socket. , The electrical socket must be easily accessible after the dishwasher has been installed. Do not connect the washing machine to the mains electricity su[...]

The Miele Waterproof system Provided that your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max.[...]

, To avoid any damage to the appliance, the dishwasher must only be connected to a fully vented plumbing system. ! The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration). New hose sets supplied with the appliance are to be used. Old hose sets should not be reused. Water connection 82[...]

Connection to the drainage system – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm. – The drain hose can be extended using a connection[...]

Dishwasher model Standard XXL Height freestanding 84.5 cm (adjustable + 3.5 cm) - Height built-in 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth: Freestanding Built-in 60 cm 57 cm - 57 cm Weig[...]

Settings menu ! for changing standard settings To open the Settings ! menu ^ Switch the dishwasher on with the On/Off sensor K if it is switched off. The programme selection menu will appear in the display. If the memory function is activated, the menu for the programme last selected will be displayed instead (see "Memory"). If this is th[...]

Language ! The display can be set to appear in one of several different languages. You can change the language for the display via the Language ! sub-menu. ^ Select the language you want and confirm this with OK . The flag after the word Language acts as a guide if a language which you do not understand has already been set. If this is the case, ke[...]

Water hardness This appliance is fitted with a water softener. The dishwasher must be programmed for the water hardness in your area (see Before using for the first time - Water hardness). Rinse aid You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. The factory default setting is 3 ml. The dos[...]

Optimise standby To save energy, the dishwasher switches off automatically a few minutes after the last time a button has been pressed or at the end of a programme. The Optimise standby function can be deactivated if wished. The dishwasher will then switch off after 6 hours. This will increase energy consumption. ^ Select the option you want and co[...]

Change main menu You can change the order of the programmes in the programme selection menu and also enter your favourite programmes into the first three programme places. Set programme for position 1 12:00 [ [ [ $ Sensor wash ( # Quick wash d 40°C m ! Cancel Continue ! ^ Select the programme you want to place in the first position of the pr[...]

Saving Extra options You can set additional functions, e.g. Pre-wash, for individual programmes (see "Operation - Selecting Extra options"). You can use the Save extras option to save settings you have chosen for a particular programme so that they are automatically selected when you run the programme in the future. The dishwasher is deli[...]

System lock The system lock prevents your dishwasher being used without your knowledge. If an attempt is made to switch the dishwasher on when the system lock is activated, Appliance locked will appear in the display. The lock must be cancelled before the dishwasher can be used. The appliance will lock each time it is switched on while the system l[...]

Temperature The temperature can be displayed in °C/Celsius or °F/Fahrenheit. The factory default setting is °C. ^ Select the option you want and confirm with OK . Volume A buzzer sounds at the end of a programme and when the machine has a fault. Buzzer at the end of a programme It will sound four times in intervals at the end of a programme with[...]

Night time You can select the times for night time to begin and end. ^ Select the Start at option in the menu. ^ Press +/- to set the start of the night time and confirm with OK . ^ Select the Finish at option in the menu. ^ Press +/- to set the end of the night time and confirm with OK . ^ Confirm the times you have set for night time with OK . Ke[...]

Showroom programme The programme is for display use only. The dishwasher is fitted with various demonstration programmes for showroom use. The Demo mode and Demo mode in continuous loop programmes demonstrate the operation and functions of the dishwasher: – Demo mode : This programme is started by pressing any button. It will run through once and[...]

95[...]

Alteration rights reserved/ G5930/G5935 / 0213 M.-Nr. 09 191 340 / 02[...]