Multi-Tech Systems FR111 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones Multi-Tech Systems FR111. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica Multi-Tech Systems FR111 o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual Multi-Tech Systems FR111 se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales Multi-Tech Systems FR111, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones Multi-Tech Systems FR111 debe contener:
- información acerca de las especificaciones técnicas del dispositivo Multi-Tech Systems FR111
- nombre de fabricante y año de fabricación del dispositivo Multi-Tech Systems FR111
- condiciones de uso, configuración y mantenimiento del dispositivo Multi-Tech Systems FR111
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de Multi-Tech Systems FR111 no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de Multi-Tech Systems FR111 y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico Multi-Tech Systems en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de Multi-Tech Systems FR111, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo Multi-Tech Systems FR111, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual Multi-Tech Systems FR111. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    Model FR1 1 1 Single Port Frame Relay Access Device with 56K DSU Owner's Manual[...]

  • Página 2

    NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio freque[...]

  • Página 3

    [...]

  • Página 4

    4 Owner's Manual 82067401 Revision B MultiFRAD TM 100-Series (Model No FR111) This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-T ech Systems, Inc. All rights reserved. Copyright © 1998, by Multi-Tech Systems, Inc. Multi-T ech Systems, Inc. makes no representations or warranties[...]

  • Página 5

    5 Contents Chapter 1 - Introduction and Description 1.1 Introduction ................................................................................. 9 1.2 About This Manual ................................................................... 1 0 1.3 A Typical Application ............................................................... 1 2 1.4 FCC R[...]

  • Página 6

    5.3 Data Port Configuration ........................................................... 5 6 5.4 Trunk Configuration ................................................................. 6 2 5.5 Statistics .................................................................................... 6 6 5.6 Diagnostics ............................................[...]

  • Página 7

    1 Introduction and Description[...]

  • Página 8

    8[...]

  • Página 9

    9 1.1 Introduction The Multi-T ech Systems MultiFRAD™ 100-Series, Model number FR1 1 1, is a one-port Frame Relay Access Device (FRAD) with 56K DSU that encapsulates non-packetized data from a serial device into frame relay frames and is responsible for framing that data with header and trailer information prior to transmission to a frame relay n[...]

  • Página 10

    10 1.2 About This Manual This manual describes the MultiFRAD, and tells you how to install and configure the unit. The information contained in each chapter is as follows: Chapter 1 - Introduction and Description Chapter 1 introduces the MultiFRAD 100-Series. A typical application is presented with a discussion on ordering a frame relay line and ho[...]

  • Página 11

    11 Chapter 6 - ASCII T erminal Menu System Chapter 6 provides a description of the ASCII terminal menu system. The ASCII terminal menu system is used when a dumb terminal is connected to the data port. These menus allow you to configure the data port and trunk, view statistics, reset the unit, and enable diagnos- tics. Chapter 7 - Service, W arrant[...]

  • Página 12

    12 1.3 A T ypical Application A typical application for a MultiFRAD 100-Series is connecting a single non-frame relay device to a frame relay network. The MultiFRAD 100- Series is usually used at a remote site where a single DLCI and a single device needs to be connected to a frame relay network. A MultiFRAD 100-Series can connect any existing sync[...]

  • Página 13

    13 your capability to present data to the local telephone switch. Y our capability to present data is determined by the internal DSU (Data Service Unit) that can transfer digital data at a maximum rate of 56,000 bits-per-second to the network. A general rule of thumb in this scenario is to assign a CIR of 32K bps and an excess burst rate (Be) of 24[...]

  • Página 14

    14 length, parity , stop bits, and flow control. The Async Data Port Configu- ration dialog box displays the default parameters that may apply to a majority async devices. When the data device is defined, then the trunk configuration needs to be defined. The trunk configuration is displayed in the T runk Configura- tion dialog box. Most of the trun[...]

  • Página 15

    15 tion. The trunk configuration would be complete by clicking on the Save button and returning to the Main menu. In the Main menu, click on the download button to transfer the configuration to the MultiFRAD. Within a few seconds the new configuration is downloaded to the MultiFRAD and it is ready for operation.[...]

  • Página 16

    16 1.4 FCC Regulations for T elephone Line Intercon- nection 1. This equipment complies with Part 68 of the FCC rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, this information must be provided to the telephone company .[...]

  • Página 17

    17 commission or corporation commission for information.) 9. If so required, this equipment is hearing aid compatible. Manufacturer: Multi-T ech Systems, Inc. Model Number: MultiFRAD 100-Series FCC Registration Number: AU7USA-24704-XD-N Ringer Equivalence: N/ A Modular Jack (USOC) RJ48 Service Center in U.S.A. Multi-T ech Systems Inc. 2205 Woodale [...]

  • Página 18

    18 1.5 Canadian Limitations Notice Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of a interface may consist of any combination of devices subject only to the requirement that the sum of the ringe[...]

  • Página 19

    19 1.6 Specifications Data Port • Single data port with synchronous or asynchronous data format • Async data rate up to 57.6K bps or sync data rate up to 56K bps • RS232C and ITU-T V .35 interface using an adapter cable • Internal shunt plugs to configure RS232C or ITU-T V .35 interface • Async data format of 5,6,7, or 8 bits; 1, 1½, or [...]

  • Página 20

    20[...]

  • Página 21

    21 2 Front and Back Panel Descriptions[...]

  • Página 22

    22[...]

  • Página 23

    23 2.1 Introduction This chapter describes the front panel LEDs and back panel connectors. The front panel has one row of LEDs for both the data channel and trunk status. T wo back panel connectors provide the data and trunk connections. A circular power connector is provided to connect the external power supply . 2.2 Front Panel The front panel co[...]

  • Página 24

    24 received - on for a space and off for a mark. DSU Data Service Unit (DSU) LED lights when the unit is in the DSU-only mode. NS The No Signal (NS) LED lights when no signal is received from the network or when the signal is too weak for normal operation. OOS The Out Of Service (OOS) LED lights when an outage condition occurs. This happens when th[...]

  • Página 25

    25 2.3 Back Panel The cable connections for the MultiFRAD are made at the back panel. T wo cable connections are provided and one power supply connection. The Data connector allows the MultiFRAD to be connected to a non- frame relay device and the T runk connector connects to a common carrier frame relay network service or private frame relay netwo[...]

  • Página 26

    26 2.4 Switch Settings The 8-position DIP switch located on the right side of the MultiFRAD only uses the first four positions. The DIP switches are shown in Figure 2-3 and their settings are described in T able 2-1. DIP-Switches Figure 2-3. Switch Settings Table 2-1. Switch Settings Switch Mode Position Description 1 Cmd/Data UP* Data DOWN Command[...]

  • Página 27

    27 2. 5 Shunts V .35 signal levels are generally more reliable for high speed data and/ or longer cable distances. EIA-232D signal levels are intended for data rates of 19,200 bps or less and cable lengths of 50 feet or less. For higher speeds and/or longer distances, V .35 is generally preferred. There are two shunt positions on the printed circui[...]

  • Página 28

    28[...]

  • Página 29

    3 Setup[...]

  • Página 30

    30[...]

  • Página 31

    31 3.1 Introduction This chapter describes the unpacking of the MultiFRAD, cable connec- tions depending on whether EIA-232D or ITU-T V .35 interface signaling is used on the data port, and how to configure the unit dependent on your site situation. Once the MultiFRAD is configured, then the data port can be connected to your data port device. 3. 2[...]

  • Página 32

    32 3. 4 Setup Use the following steps to setup your MultiFRAD. If V .35 electrical interface signaling is required on the data port, but a pc with EIA-232D signaling is being used to configure the MultiFRAD, the unit has to be configured before you change to V .35 signaling. Perform the following procedure to connect your cables, configure the unit[...]

  • Página 33

    33 4. Connect an RJ48 phone cable to the Trunk connector on the back of the MultiFRAD. Connect the other end of the phone cable to the local access line jack. T runk Data Powe r Figure 3-4. T runk Connection 5. The MultiFRAD can be configured in two ways: If a pc running a Windows software is being used to configure the unit, refer to the Software [...]

  • Página 34

    34 3.5 V .35 Shunt Either EIA-232D or ITU-T V .35 electrical signal interface can be selected on the data port. Units are shipped with EIA-232D signal levels se- lected. Use the following procedure to select V .35. CAUTION This procedure requires opening the unit. Like most products of this type, this product contains components that are sensitive [...]

  • Página 35

    35 4 Software Loading and Configuration[...]

  • Página 36

    36[...]

  • Página 37

    37 4.1 Introduction This chapter covers the loading of the software utility and then the configuration of the unit from either a Windows based pc or a dumb terminal. When a Windows based pc is used, the software utility is loaded using the procedures in section 4.2 and then the unit is config- ured using the procedures in section 4.3. If a dumb ter[...]

  • Página 38

    38 Click on Install to continue installation, at any time you may click on Abort if you wish to cancel the install immediately . 9 The Expanding/Copying Files From: dialog box is displayed. Y ou can view the progress of the installation from this dialog box. Y ou can click on Abort at any time to cancel the install. 1 1 The MultiFRAD 100 Installati[...]

  • Página 39

    39 Select the COM port ( COM1,COM2,COM3, or COM4 ) for the setup utility . The default port is COM1. Click on OK when you are satisfied with your selection. 1 2 When the setup installation is successful, a system message is displayed stating "MultiFRAD 100 Installation Successful. Click on OK to continue. 1 3 Y our are returned to the Program [...]

  • Página 40

    40 4.3 Configuring Y our MultiFRAD using Windows Configuration of your MultiFRAD using Windows starts after the soft- ware is loaded and program group is displayed in the Program Man- ager . 1 Double click on the MultiFRAD 100 Configuration icon. 2 When the MultiFRAD 100 dialog box is displayed, click on the Data Port button to display the Data Por[...]

  • Página 41

    41 If your data device is a synchronous device, click on the Syn- chronous option button and the parameters for the synchronous mode are displayed. Refer to the User documentation to set the sync parameters that meet the conditions of your installation. 4 When you are satisfied with your selections, click on the Save button to save your new paramet[...]

  • Página 42

    42 6 Click on the DLCI numeric dialog box. Enter the DLCI number that was provided by your service provider at subscription time. T o change the DLCI, click on the DLCI numeric dialog box and back space through the default number and then enter your DLCI. 7 Click on the Management type option button supported by your Frame Relay network. The Manage[...]

  • Página 43

    43 another MultiFRAD 100. Raw Mode encapsulation can be used for any type of FRAD at the other end. 1 2 Click on the OK button to return to the Main menu. 1 3 Click on the Download button to write the new configuration to the MultiFRAD. 1 4 The Configuration dialog box is displayed. The Configuration downloaded successfully . Reset the unit for con[...]

  • Página 44

    44 4.4 Configuring your MultiFRAD using a Dumb T erminal T o configure your MultiFRAD, power up a terminal or pc running communications software and hit the ENTER key . The Main menu appears on your screen, configure the data port for sync or async mode of operation and the trunk for the frame relay parameters. The Multi- FRAD configuration is cont[...]

  • Página 45

    45 4 If the data port is being setup for Async mode of operation and a port speed of 57.6K, initially the data port does not have to be changed, proceed to step 6 to configuring the T runk. Data Port Configuration 1 - Async/Sync: Async 2 - Speed: 57600 3 - Word Length: 8 4 - Stop Bits: 1 5 - Parity: None 6 - Flow Control: CTS 7 - Enq/Ack Flow Contr[...]

  • Página 46

    46 6 From the Configuration menu, enter 2 and press ENTER . The T runk Configuration menu is displayed. T runk Configuration 1 - Access rate: 56000 2 - RTS Signal S tatus: Follows input from DTE 3 - Back to Back: Off 4 - DLCI: 16 5 - Committed Info Rate(CIR): 32K 6 - Excess Burst Rate (Be): 24K 7 - Management type : Annex A 8 - Polling Interval: 10[...]

  • Página 47

    47 Enter the number that corresponds to the DLCI for your trunk. A two-digit number can be entered and the zeros will proceed the digits. The DLCI is supplied by your network service provider at the time the trunk was provisioned. When you have entered your DLCI, the T runk Configuration menu is displayed. 8 From the T runk Configuration menu, ente[...]

  • Página 48

    48 The Be is supplied by your network service provider at the time the trunk was provisioned. When you have entered your Be, the T runk Configuration menu is displayed. 1 0 From the T runk Configuration menu, enter option 7 Management T ype and the Management T ype menu is displayed. Management Type 1 - Annex D (ANSI T1.617) 2 - LMI 3 - Annex A (IT[...]

  • Página 49

    49 Enter the Full Status Counter. Valid values are between 1 and 255. x - Enter Number, or P - Previous Menu Selection : _ Enter the number between 1 and 255 that is going to be the number of polling cycles (minus one) before a full status is requested from the network. 1 3 From the T runk Configuration menu, enter option 10 Error Threshold and the[...]

  • Página 50

    1 5 Enter the letter S and press ENTER to store all configurations. Then enter the letter M and press ENTER to return to the Main Menu. Enter 5 to Exit Command Mode. 1 6 Place the Command Mode switch (Switch 1) on the side of the MultiFRAD in the UP position and return to step 6 in the Setup procedure in Chapter 3.[...]

  • Página 51

    5 Software Utility Descriptions[...]

  • Página 52

    52[...]

  • Página 53

    53 5.1 Introduction This chapter describes the MultiFRAD software which is designed for the Microsoft ® Windows ® environment. The MultiFRAD 100 Program Group has three icons that allow you to launch the software, download a firmware update, and configure the console pc port in order to communicate with the MultiFRAD. The MultiFRAD 100 Configurat[...]

  • Página 54

    54 5.2 .1 Configuration Data Port This button allows you configure the data port for either synchronous or asynchronous mode of operation. Trunk This button lets you define the frame relay parameters. 5.2.2 Others Statistics This button allows you to view statistics of the trunk port. Diagnostics This button allows you to run two loopback tests, a [...]

  • Página 55

    55 5. 2 .5 Help A thorough On-line Help system is provided with abbreviated informa- tion on the dialog boxes and the buttons within a dialog box. 5.2 .6 MultiFRAD V ersion The current version number of the MultiFRAD firmware is displayed in this field.[...]

  • Página 56

    56 5.3 Data Port Configuration This dialog box allows you to configure the data port. Y ou will be able to set the parameters required for the successful operation of the port. Mode Asynchronous/Synchronous This allows you to set synchronous or asynchronous parameters required for transferring data between the MultiFRAD and the data port device. Th[...]

  • Página 57

    57 Note: The MultiFRAD always provides the clocking signal to the sync device. The MultiFRAD 100's data port can not be set to external clocking, it is always internal clocking. Between Frames The Between Frames parameter must be set to match the idle condition of the synchronous device connected to the data port. The Between Frames determine [...]

  • Página 58

    58 CRC Preset The CRC Preset parameter allows the user to specify whether the polyno- mial used to calculate the CRC for each frame is preset to all 1s or all 0s. This option must match the synchronous device’s CRC-preset setting. The default is All 1s. Async Mode Parameters Following Parameters are modifiable when the device connected to the dat[...]

  • Página 59

    59 Parity The Parity parameter sets parity for odd, even or none. Under normal conditions, parity is set to none. The default is none. Stop Bits The Stop Bits parameter sets the number of stop bits. The number of stop bits can be 1, 1.5, or 2. The default is 1 bit. Flow Control The Flow Control parameter allows for two types of flow control: the so[...]

  • Página 60

    60 Pass Xon The Pass Xon parameter enables the XON/XOFF flow control signals to be passed on to the data device. This option has to be used in conjunction with the software-based XON/XOFF flow control option. The default condition is for this option to be turned off, and normally it should remain off. Echo The Echo parameter enables data entered on[...]

  • Página 61

    61 ENQ/ACK The Enq/Ack parameter is a special flow control protocol used in Hewlett Packard computer systems. This option is sometimes referred to as Enquire/Acknowledge flow control because it’s based on the computer sending an enquiry (ENQ) and then expecting an acknowledgment (ACK).[...]

  • Página 62

    62 5.4 T runk Configuration This dialog box allows you to configure the trunk. Y ou will be able to set the parameters required for the successful operation of the trunk. Frame Relay is a multiplexing protocol designed to operate over transmission facilities that are virtually error free. In Frame Relay , frames are routed through the network on th[...]

  • Página 63

    63 LMI describes a protocol and associated procedures operating on the local interface between the user and the network. It notifies the user of the addition, deletion, and presence of the PVC in the network. It also notifies the user of the end-to-end availability or unavailability of a PVC. Basic LMI protocol is based on a synchronous polling sch[...]

  • Página 64

    64 Full Status Counter The Full Status Counter determines how may Polling Intervals take place before a full status is requested from the network. A full status enquiry message is sent from the MultiFRAD to the network requesting a status report of the PVC on the physical link. The Full Status Counter can range from 1 to 255, with a default of 6. E[...]

  • Página 65

    65 Back to Back The Back to Back is used to test the port by connecting two MultiFRADs together without a frame relay network in between them. Back-to-back mode still requires the use of DSU/CSUs, but they should not be connected over the frame relay network. The options are On and Off with a default of Off. Back-to-back mode is useful when two Mul[...]

  • Página 66

    66 5.5 Statistics This dialog box allows you to view status of the trunk. Its possible to view signal status and other characteristics like data frames transmitted or received, status of enquiries transmitted and messages received and the status of the messages received. If you want to clear the statistics so that you can have fresh statistics, the[...]

  • Página 67

    67 Loop Tests The loop tests provide a short and long loop test. The short loop test is the data port loopback test which loops back the data from the data port to the sending device (DTE). The long loop test is the trunk loopback test which again receives data from the DTE device and loops it back from the internal DSU. The data port loopback test[...]

  • Página 68

    [...]

  • Página 69

    6 ASCII T erminal Menu System[...]

  • Página 70

    70[...]

  • Página 71

    71 6.1 Introduction The menu system for the MultiFRAD provides a set of user-friendly configuration menus that are accessible from a main menu. The Main Menu contains five options that allow you to configure your MultiFRAD; display statistics; reset the unit or data port; run diagnostic tests, and exit the command mode. T o select one of the option[...]

  • Página 72

    72 a message will appear on your screen saying to wait for 3 seconds. Then press ENTER to return to the Main Menu. T o store the current configuration, enter S and press ENTER. T o return to the Main Menu, enter M and press ENTER. 6.2 .1 Async Data Port Configuration The Async Data Port Configuration menu allows you to configure the data channel fo[...]

  • Página 73

    73 The W ord Length option sets the number of bits in a word. The word length range is 5 to 8 bits. The default is 8 bits. The Stop Bits option sets the number of stop bits. The number of stop bits can be 1, 1.5, or 2. The default is 1 bit. The Parity option sets parity for odd, even or none. Under normal conditions, parity is set to none. The defa[...]

  • Página 74

    74 The EIA Pass Through option allows the data device to receive EIA control signals through the MultiFRAD. This option only applies during the async mode of operation. Since, in normal interactive operation, the existence of a MultiFRAD should be transparent to the user , the EIA pass through option allows a terminal to operate as if it were conne[...]

  • Página 75

    75 6.2 .2 Sync Data Port Configuration The Sync Data Port Configuration menu allows you to configure the data port for either asynchronous or synchronous operation, depending on the type of device connected to the port. When the port is configured for synchronous operation, the following Data Port Configuration menu displays the default parameters:[...]

  • Página 76

    76 ing, data is represented normally . With NRZI encoding, a logical one is represented by no transition and a zero is represented by a transition at the beginning of the bit. Most synchronous devices can be configured for either NRZ or NRZI. If a synchronous device is not configurable, it most likely is set to NRZ. Refer to the device’s user doc[...]

  • Página 77

    77 6.2 .3 T runk Configuration The T runk Configuration menu allows you to configure the trunk. The default parameters are displayed in the following menu: T runk Configuration 1 - Access rate: 56000 2 - RTS Signal S tatus: Follows input from DTE 3 - Back to Back: Off 4 - DLCI: 16 5 - Committed Info Rate(CIR): 32K 6 - Excess Burst Rate (Be): 24K 7 [...]

  • Página 78

    78 access circuit. Set the DLCI to indicate the PVC to terminate the trunk. The range of DLCIs is from 16 to 1007 with a default of 16. The Committed Info Rate (CIR) option determines the data transfer rate at which the network is committed to handle under normal conditions. This rate is the average over a minimum increment of time. The CIR may be [...]

  • Página 79

    79 should be less than or equal to the Monitored Event Counter . The Monitored Event Counter option determines the number of Polling Intervals that have to take place before the User Network Interface is operational. It is also used with the error threshold count to determine if the trunk should be brought down. The range of this counter is from 1 [...]

  • Página 80

    80 6.3 Statistics The Statistics menu allows you to view or clear statistics, or return to the previous menu or to the Main Menu. Statistics 1 - View Statistics 2 - Clear Statistics M - Main Menu P - Previous Menu Selection : _ T o view or clear statistics, enter the corresponding option number and press ENTER . T o return to the previous menu, ent[...]

  • Página 81

    81 you might encounter could be 10,000 frames transmitted (or received) with 500 or 1000 retransmits (or receive errors). Link alarms simply tell you that there is some sort of problem on the trunk in async mode. Y ou will find that the link alarms number will correspond to the retransmit and received frames numbers. Specifically , a link alarm mea[...]

  • Página 82

    82 6.4 Reset Options The Reset Options menu allows you to reset the unit, the data channel, or return to the previous menu or to the Main Menu. Reset Options 1 - Reset Unit 2 - Reset Data Channel M - Main Menu P - Previous Menu Selection : _ T o reset the unit, enter 1 and press ENTER . T o reset the data channel, enter 2 and press ENTER . T o retu[...]

  • Página 83

    83 loopback mode (DIP-Switch 3 DOWN). This tests the complete path through the MultiFRAD up to the line circuitry and back to the data port. When it is used in a remote trunk loopback test mode, the remote DSU (or the telephone company's central office, CO) would be put into loopback mode. This tests the integrity of the local data device, Mul[...]

  • Página 84

    84 try going back to the Local T runk Loopback, and then even the data port loopback which is the most basic test. If there is still no clear cause of the problem, follow the steps in section 7.3, contacting T ech support. 6.5 .2 Memory T est The memory test verifies that each memory chip on the circuit board is working. The memory test destroys al[...]

  • Página 85

    7 Service, W arranty and T ech Support[...]

  • Página 86

    86[...]

  • Página 87

    87 7.1 Introduction This chapter begins with your MultiFRAD 100-Series 2-year warranty . Read carefully the next section, “T ech Support,” if you have questions about or problems with your MultiFRAD. It includes the technical support telephone numbers, space for recording your product information, and an explanation of how to send in your Multi[...]

  • Página 88

    88 7.3 .1 Recording MultiFRAD Information Please fill in the following information on your Multi-T ech MultiFRAD. This will help T ech Support in answering your questions. (The same information is requested on the Warranty Registration Card.) Model Number: ______________________________________ Serial Number: ______________________________________ [...]

  • Página 89

    89 7.3 .2 Service If your tech support specialist decides that service is required, your MultiFRAD may be sent (freight prepaid) to our factory . Return shipping charges will be paid by Multi-T ech Systems. Include the following with your MultiFRAD: • A description of the problem. • Return billing and shipping addresses. • Contact name and ph[...]

  • Página 90

    90 7.4 . 1 Logging on to the Multi-T ech BBS T o log on to the Multi-T ech BBS, perform the following steps. 1. Set your communications program to 8-N-1 . 2. Dial our BBS at (800) 392-2432 (USA and Canada) or (612) 785- 3702 (international and local). 3. At the prompts, type your first name, last name, and password; then press ENTER. If you are a f[...]

  • Página 91

    91 If you don’t know the file name 1. From the Main Menu, type F to access the Files Menu. For a list of file areas, type L , press ENTER, then type L and press ENTER again. (If you do not type the second L , you will list all of the files on the BBS.) 2. Mark each file area you would like to examine by typing its list number and pressing ENTER. [...]

  • Página 92

    92 7.6 About the Internet Multi-T ech is a commercial user on the Internet, and we retrieve messages from our customers on a periodic basis. Multi-T ech’s pres- ence includes a Web site at: http://www .multitech.com and an ftp site at: ftp://ftp.multitech.com Multi-T ech's presence includes a Web site at: 7.7 About the Multi-T ech Fax-Back S[...]

  • Página 93

    93 7.8 Upgrading the Flash PROM Y our MultiFRAD has a Flash PROM which contains firmware code for the hardware. At various times, Multi-T ech may add enhancements and/ or fixes to the firmware. The Flash technology used in your MultiFRAD allows these upgrades to be loaded directly into the PROM chip through the serial port. 7.8.1 Using FlashPro to [...]

  • Página 94

    94[...]

  • Página 95

    Appendices[...]

  • Página 96

    96[...]

  • Página 97

    97 Appendix A Cabling Diagrams PIN NO. 1 2 3 4 5 7 8 15 17 20 25 1 2 3 4 5 7 8 15 17 20 25 CHASSIS GROUND (AA) TRANSMIT DA T A (BA) RECEIVE DA T A (BB) REQUEST TO SEND (CA) CLEAR TO SEND (CB) SIGNAL GROUND (AB) CARRIER DETECT (CF) TRANSMIT CLOCK (DB) RECEIVE CLOCK (DD) DA T A TERMINAL READY (CD) PIN NO. Data Cables RS232C/V .24 * Cable T o FR1 1 1 [...]

  • Página 98

    98 T runk Cable 1 2 3 4 5 6 7 8 RT RR RT RR { { Receive T ransmit RJ-48 Cable Pin Identification P in Description Destination 1 T ransmit Pair T o Line 2 T ransmit Pair T o Line 3 N/C 4 N/C 5 N/C 6 N/C 7 Receive Pair From Line 8 Receive Pair From Line[...]

  • Página 99

    99 Back-T o-Back Cable RJ48S 1 2 3 4 5 6 7 8 RJ48S 8 7 6 5 4 3 2 1 1 8[...]