NEC LCD8205-P manual

User ’ s Manual MultiSync LCD8205 MultiSync LCD8205-P[...]

Index Declaration of conformity ...................................................................................................... ....................... English-1 Important Information .......................................................................................................... ......................... English-2 W arning, Cautio[...]

English-1 English For USA FCC Information 1. Use the attached specified cables with the MultiSync LCD8205 (L828N0)/MultiSync LCD8205-P (L828N0) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cab[...]

English-2 Important Information TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT T O RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPONENTS INSIDE. REFER SERVICING T[...]

English-3 English FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TI-FUNCTION MONITOR: • DO NOT OPEN THE MONITOR . There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not s[...]

English-4 Contents Power Cord* 1 Setup Manual DVI-D to DVI-D cable Wireless Remote Control and AAA Batteries Clamp Y our new MultiSync LCD monitor box* should contain the following: • LCD monitor • Power Cord* 1 • V ideo Signal Cable • Setup Manual • Wireless Remote Control and AAA Batteries • Clamp • Screw for clamp (M4 x 10) x 2 •[...]

English-5 English This de vice cannot be used or installed without the T ab letop Stand or other mounting accessor y f or suppor t. F or proper installation it is strongly recommended to use a trained, NEC authorized service person. F ailure to f ollow NEC standard mounting procedures could result in damage to the equipment or injury to the user or[...]

English-6 4. Attach Mounting Accessories The display is designed for use with the VESA mounting system. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA- compatible mounting method. NEC strongly recommends using screws M8 size and 10 - 18 mm in length. If using screws longer than 18 mm, check the[...]

English-7 English 1 POWER button ( ) Switches the power on/off. 2 CH +/- button Acts as button to move the highlighted area up or down to select adjustment items within OSD menu. 3 VOL +/- button Increases or decreases audio output level. Increases or decreases the adjustment level within OSD menu settings. 4 SEL button Enter Input Source OSD menu,[...]

English-8 T erminal Panel 1 HDMI connector T o input digital HDMI signals. 2 DVI IN (DVI-I) T o input digital or analogue RGB signals from a computer . 3 SPDIF Optical digital audio out for HDMI input only . 4 EXTERNAL CONTROL (D-Sub 9 pin) Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions. 5 Audio Inp[...]

English-9 English NOTE: The button without explanation doesn’t work. 1 POWER button Switches the power on/off. 2 SOURCE button Enter Input Source OSD menu, [DVI], [PC], [HDMI], [A V1], [A V2], [S-Video] and [Component]. 3 MUTE button T urns on/off mute function. 4 INFO button T urns on/off the information OSD. 5 STILL button T oggles picture stat[...]

English-10 1. Determine the installation location CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. CAUTION: IN ORDER T O AID IN MOUNTING, A LIFTING DEVICE MUST BE USED IN CONJUNCTION WITH THE A TT ACHABLE EYEBOL TS. MOVING OR INST ALLING THE LCD MONIT OR MUST BE DONE BY FOUR OR M[...]

English-11 English 5. Switch on the power of all the attached external equipment When connected with a computer , switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required. 8. Adjust the screen (See page 18) Make a[...]

English-12 Connections Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video [...]

English-13 English Connect the LCD Monitor to a DVD Player • T o connect the Component connector (RCA) on the LCD monitor , use an RCA connector cable (sold separately). Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user ’s manual for more[...]

English-14 Connecting to a Stereo Amplifier Y ou can connect your stereo amplifier to your LCD monitor . Refer to your amplifier owner ’s manual for more information. LCD monitor Amplifier External speaker External speaker Connecting a DVD Player with HDMI out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Re[...]

English-15 English Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red while powered off. Power Button[...]

English-16 Power Indicator Mode Power ON Power OFF (Standby)* Power consumption under 1W Power Save Power consumption under 15W Not connected Using Power Management The LCD monitor follows the VESA approved DPM Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of t[...]

English-17 English OSD (On-Screen-Display) Controls Press MENU button to show OSD menu. Press UP and DOWN to select the main menu. Press Right button to enter the sub menu. Press EXIT to exit menu. Remote Control Press MENU button to show OSD menu. Press CH+ and CH- buttons to select the main menu. Press VOL+ button to enter the sub menu. Press MEN[...]

English-18 OSD Setting Picture Picture Mode User Store last value at User setting. Dynamic Selection of the picture appearance. Standard Movie Mild User Brightness Adjust the brightness. Contrast Adjust the Contrast. Color (A V1/A V2/S-Video/Component) Adjust the Color . T int (A V1/AV2/S-V ideo/Component) Adjust the T int. Sharpness Adjust the Sha[...]

English-19 English Sound Mode User This function use setting Equalizer value. Standard Selection of preset Sound mode (Equalizer). Music Movie Speech V olume Adjust the sound volume level. Balance T uning the sound balance between left and right. Equalizer 10 KHz The value of 5 Band equalizer are preset. 3 KHz These values are changed by user with [...]

English-20 Advanced Dimming Auto Dimming Enable/Disalbe Auto Dimming control by Abient Light sensor . Dim Level Display current Dim Level. MAX Dim Ambient Adjusts detected light ambient to set the maximun dimming. MIN Dim Ambient Adjusts detected light ambient to set the minimun dimming. Ambient Display current detected light ambient level by Lux u[...]

English-21 English Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC NOTE: If your PC (IBM or IBM compatib[...]

English-22 Features Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus. Plug and Play: The Microsoft ® solution w[...]

English-23 English T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display c[...]

English-24 Specifications Product Specifications LCD Module 81.6"/207 cm diagonal Pixel Pitch: 0.744 mm Resolution: 1920 x 1080 dots Color: Over 16 million colors (depending on video card used) Brightness: 600 cd/m 2 (T yp.) (LCD8205)/450 cd/m 2 (T yp.) (LCD8205-P) Contrast Ratio: 2000:1 Viewing Angle: 89° (typ) @ CR>10 (LCD8205)/85° (typ[...]

English-25 English Pin Assignment 1) S-VIDEO input: VIDEO Pin No Name 1G N D 2G N D 3 Y (Luminance) 4 C (Chroma) 2) Digital/Analog RGB input: DVI-I 3) RS-232C input Pin No Name 1 connected to 7&8 2 RXD 3 TXD 4 connected to 6 5G N D 6 connected to 4 7 connected to 1&8 8 connected to 1&7 9N C Pin - Assignment of DVI connector: 1 TX2- 9 TX[...]

English-26 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. W e are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standar[...]