OKI Microline 390FB manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones OKI Microline 390FB. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica OKI Microline 390FB o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual OKI Microline 390FB se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales OKI Microline 390FB, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones OKI Microline 390FB debe contener:
- información acerca de las especificaciones técnicas del dispositivo OKI Microline 390FB
- nombre de fabricante y año de fabricación del dispositivo OKI Microline 390FB
- condiciones de uso, configuración y mantenimiento del dispositivo OKI Microline 390FB
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de OKI Microline 390FB no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de OKI Microline 390FB y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico OKI en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de OKI Microline 390FB, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo OKI Microline 390FB, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual OKI Microline 390FB. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    MICROLINE 320/390FB User Manual (English) MICROLINE 320/390FB User Manual (English)[...]

  • Página 2

    E – 1 English Table of Contents Note to Customers ................................... E-2 Important Safety Instructions .................. E-3 Important Wiring Instructions ................. E-4 Installing Your Printer ............................. E-5 Preliminaries ............................................ E-6 Connecting to the Computer .....[...]

  • Página 3

    E – 2 Note to Customers Every effort has been made to ensure that the information in this manual is complete, accurate and up-to-date. Oki assumes no responsibility for errors beyond its control. Oki also can not guarantee that changes in software and equipment made by other manufacturers and referred to in this book will not affect the applicabi[...]

  • Página 4

    E – 3 Important Safety Instructions Your printer has been carefully designed to perform safely and reliably. However, as with all electrical equipment certain precautions should be allowed: ➢ Read all documentation supplied with and on the printer before commencing. ➢ Always disconnect the printer from the mains source before cleaning. ➢ Be[...]

  • Página 5

    E – 4 Important Wiring Instructions The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live If the colours of the wires in the mains lead of this printer do not correspond with the markings of the terminals of your plug, proceed as follows: Green and Yellow must be connected t[...]

  • Página 6

    E – 5 Installing Your Printer Prior to unpacking the printer, find a flat, sturdy surface to place it on, for example, a desk, printer stand, etc. Gently remove the printer from its carton. Make sure you have everything shown below: ➢ MICROLINE 320/390 FLATBED printer ➢ Sheet stacker ➢ Power cord ➢ Ribbon cartridge ➢ Printer Handbook No[...]

  • Página 7

    E – 6 Preliminaries Before plugging in the printer, follow these steps to install your printer. 1. Hold both sides of the access cover and lift up. There is a shipping retainer to protect the printhead from jamming. Remove this shipping retainer and keep it with the other packing materials. (To transport the printer long distances, make sure to r[...]

  • Página 8

    E – 7 2 . Next install the sheet stacker. Put the stud of one of the stacker’s legs into the hole at the end of the rear vent. Gently press the other leg until it slips into the other hole. 3 . Make sure the power switch is OFF. Plug the power cord into the back of the printer. Plug the other end into an earthed socket. 4. Turn the power switch[...]

  • Página 9

    E – 8 5. Turn the power switch off. Important: Make sure the socket is earthed. Do not use an adapter because it will defeat the earthing. ![...]

  • Página 10

    E – 9 Connecting to the Computer These instructions are for the standard centronics parallel interface. 1 . Make sure that both the printer and the computer are switched OFF. 2 . Plug the interface cable into the port on the back of your printer. Fasten the the cable using the wire clips that can be found on both sides of the connector port. 3 . [...]

  • Página 11

    E – 10 Installing the Ribbon Cartridge 1 . Set the headgap lever to the “R” position. 2 . Open the access cover. 3 . Slide the print head gently towards the centre to give yourself some working room. There is a cut-out at the centre of the sheet guide for changing cartridges. Important: a) The printhead gets very hot during extended periods o[...]

  • Página 12

    E – 11 5 . Insert the flat end of the cartridge into the upper part of the ribbon plate, then lower the front of the cartridge over the printhead until it snaps into place. 6 . Turn the take-up knob in the direction of the arrow icon to tighten the ribbon. 7 . To remove a ribbon, move the cartridge to the position indicated by two arrow icons at [...]

  • Página 13

    E – 12 Important: Do not peel off the plastic film (ribbon mask) on the top of the cartridge. Do not stack the ribbon cartridge sideways, it will cause poor quality printing. Loading Paper Loading Continuous Paper 1 . Check that the POWER lamp is turned on. 2 . Check that the SEL lamp is turned off. If it is lit, push the SEL button once to turn [...]

  • Página 14

    E – 13 3 . Push the paper lever to the continuous paper position. 4 . Adjust the headgap lever on the left side of the printer according to your paper thickness. At its lowest (position 1), the lever sets a thickness for one sheet of paper. It clicks through seven positions showing the number of sheets. The eighth position is for extra-thick pape[...]

  • Página 15

    E – 14 Note: In the positions above 5, the printer slows down to maintain print quality with thicker multipart forms. Note: “R” position indicates ribbon cartridge replacement position. 5 . Hold both sides of the paper table and lift up gently. 6 . Open the lock levers on both pin tractors. This unlocks the pin tractor so that you can adjust [...]

  • Página 16

    E – 15 7 . Open both of the pin-tractors covers. 8 . Lay down the continuous paper with printing face upwards on to the pin-tractors. Adjust the paper so that the first two pins of both pin tractors poke through the two sprocket holes of the paper. Make sure that the paper covers the pin tractors. Important:The space between the left edge of the [...]

  • Página 17

    E – 16 Note: The arrow icon ( ▼ ▼ ▼ ▼ ▼ ) on the scale and also the centre of the diamond shaped hole indicate the centre of the first printed character. 10. Slide the right pin-tractor to tighten the paper. Press the right lock lever down. (Lock position.) Close the pin tractor cover. ! Pin tractor cover Lock lever Scale Lock lever Pin[...]

  • Página 18

    E – 17 11. Close the table. The extension guide is not necessary when using continuous paper. Push it clockwise so that it folds under the sheet stacker. 12. When you close the table, the ALARM lamp comes on, do not worry, it is just telling you that there is no paper loaded. Press the FORM FEED button. Your paper will be loaded automatically. Th[...]

  • Página 19

    E – 18 Loading Cut Sheet paper 1 . Check that the power is on. 2 . Check that the SEL lamp is off (printer off-line). If it is on push the SEL button to turn it off. 3 . Pull the paper lever to the forwards position, (cut sheet paper position). 4 . Position the headgap lever to the appropriate setting for your paper thickness. Note: You can not p[...]

  • Página 20

    E – 19 Note: Unless you alter the standard margin setting using the MENU MODE, the paper guide must be placed correctly against the arrow icon: too big a left margin may cause printing on the platen and not the paper, resulting in a loss of data. 6. The sheet will be loaded automatically. The ALARM lamp goes off and the SEL lamp comes on, you are[...]

  • Página 21

    E – 20 Setting the Top of Form Your printer can adjust the top of form (the first line of the printing surface) by increments of 1 / 144 inch. This allows you to set a desired top of form very precisely. 1. To advance the paper, keep pressing the TOF/ QUIET button and press the FORM FEED button. 2. To reverse, keep pressing the TOF/QUIET button a[...]

  • Página 22

    E – 21 3 . Release the two buttons at the desired top of form position. Press the TOF/QUIET button again to fix the setting. It remains in the printer’s memory and will not change until the printer is reset. Note 1: The reverse process is limited in order to avoid paper jams. Note 2: You can also preset the top of form by hand. Make sure the SE[...]

  • Página 23

    E – 22 2 . Also, keep the printer 60 cm or more from the wall in order to store paper. These storage requirements are necessary to avoid jammmg. Running a Self Test Now that you have installed the ribbon and paper, you are ready to run one of two types of self test. The default paper setting is 269.24mm. When using paper of smaller width, change [...]

  • Página 24

    E – 23 Printing Demo Patterns 1 . First load the printer with the correct paper. 2 . Switch off the power to the printer. 3 . Choose the demo pattern you want to produce and associated button, from the following table. 4 . Keep pressing the button and turn on the power. The self test will start almost immediately. 5 . In self test mode, the print[...]

  • Página 25

    E – 24 Changing Menu Settings To change the menu settings follow these steps: 1. Make sure that the printer is on line. 2 . Press the MODE/Exit button to put the printer in Menu Mode. 3 . Press the TOF/QUIET/Print button to print a list of menu settings. 4 . Press the LINE FEED/Group button to select the menu group. 5 . Press the FORM FEED/Item b[...]

  • Página 26

    E – 25 If you want to return the printer to the factory default settings, turn the power on while holding down the MODE/Exit and SEL buttons, all menu settings will then return to the factory default. An example of a menu printout: ML320FB ML390FB[...]

  • Página 27

    E – 26 Specifications Print method Impact dot matrix Printhead 24 pin (ML390FB) 9 pin (ML320FB) Print speed Utility 270 cps at 12 cpi (ML390FB) 250 cps at 12 cpi (ML320FB) Letter quality 90 cps at 12 cpi (ML390FB) 62.5 cps at 12 cpi (ML320FB) Characters per line at 10 cpi 106 at 12 cpi 127 at 15 cpi 159 at 17.1 cpi 181 at 20 cpi 212 Reliability M[...]

  • Página 28

    E – 27 Electrical characteristics Voltage 230V AC(+6%-14%). 240V AC(±10%). Frequency 50/60Hz ±2%. Data interface Centronics parallel standard. RS232C serial optional. Dimensions Depth 343mm. Width 465mm. Height 200mm. Weight 12kg. Continuous paper Wid th 76.2mm to 304.8mm. Length 76.2mm to 355.6mm. Single part Weight 12 t o 34lb. Thickness 0.05[...]

  • Página 29

    E – 28 Cut sheets Wid th 90mm to 304.8mm. Length 70mm to 420mm. Single part Weight 12 t o 41lb. Thickness 0.051mm to 0.196mm. Multipart* Weight Paper: 10 to 12lb. Carbon: 9lb. Number of copies Original plus 4 copies. Thickness 0.36mm max. * Note: All parts must be glued at the top. Envelopes (individual) Weight 24lb. max. Thickness 0.406mm max. D[...]