Onkyo HT-R518 manual

E n AV Receiv er HT -R518 Instruction Manual Thank you for purchasing an Onkyo A V Recei ver . Please read this manual thoroughly before making connections and plugging in the unit. F ollo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiver . Please retain this manua[...]

2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat so[...]

3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The AC fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact your Onkyo dealer . 3. Care —Occasionally you should dust the unit[...]

4 Precautions —Continued F or British models Replacement and mounting of an AC plug on the po wer supply cord of this unit should be performed only by qualified service personnel. IMPOR T ANT The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Li ve As the colours of the wires in the mains lead of[...]

5 Contents Important Safety Instructions........................... 2 Precautions ....................................................... 3 Supplied Accessories ...................................... 4 Features ............................................................ 6 Getting to Know the AV Receiver ................... 7 Front Panel ..........[...]

6 Features Amplifier • 130 W atts/Channel @ 8 ohms (IEC) • WRA T -W ide Range Amplifier T echnology (5Hz–100kHz bandwidth) • High-Current Low-Impedance Dri ve • Optimum Gain V olume Circuitry • H.C.P .S. (High Current Power Supply) Massi ve High Power T ransformer Processing • Dolby Digital and Pro Logic II *1 • DTS, DTS 96/24 and[...]

7 Getting to Kno w the A V Receiver The actual front panel has various logos printed on it. They are not sho wn here for clarity . The page numbers in parentheses show where you can find the main e xplanation for each item. A ON/ST ANDBY b utton (33) Sets the A V receiver to On or Standby . B ST ANDBY indicator (33) Lights up when the A V receiver[...]

8 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. U MEMOR Y b utton (45) Used when storing or deleting radio presets. V TUNING MODE button (43) Selects the Auto or Manual tuning mode for AM and FM radio. W SETUP MIC (34) The automatic speaker setup microphone connects here. X A UX INPUT (28, 54)[...]

9 Getting to Know the A V Receiver —Continued A DIGIT AL IN OPTICAL 1 and 2 These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or D VD player . They’ re assign- able, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” [...]

10 Getting to Know the A V Receiver —Continued M VCR/D VR IN/OUT A video component, such as a VCR or D VR, can be connected here for recording and playback. There are S-V ideo and composite video input and output jacks for connecting the video signal, and there are analog audio input jacks for connecting the audio signal. N D VD IN This input is [...]

11 Remote Contr oller For detailed information, see the pages in parentheses. A ON/ST ANDBY b utton (33) Sets the A V receiv er to On or Standby . B REMO TE MODE/INPUT SELECT OR buttons (39, 66–72) Selects the remote controller modes and the input sources. C MUL TI CH b utton (39) Selects the multichannel D VD input. D Arro w [ ]/[ ]/[ ]/[ ] and [...]

12 Remote Controller —Continued Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or dif ferent types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion. • Expired bat[...]

13 Connecting Y our Speakers Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring Dolby Digital or DTS. W ith analog or digital TV , you can enjoy Dolby Pro Logic II, DTS Neo:6, or Onkyo?[...]

14 Connecting Y our Speakers —Continued Speaker Configuration F or 5.1-channel surround-sound playback, you need fiv e speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve. No matter how man y speakers you use, a po wered sub- woofer is recommended for a po werful[...]

15 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of between 8 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high v olume lev els for a long period of time, the built-in amp pro- tection cir[...]

16 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up an y radio signals without any antenna connected, so you must connect the antenna to use the tuner . The supplied indoor FM antenna [...]

17 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft. •F or best results, install the outdoor FM an[...]

18 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Digital Jacks The A V receiver’ s optical digital jacks hav e shutter-type cov ers that open when an optical p[...]

19 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver. The A V receiver supports se veral connection formats for compatibility with a[...]

20 Connecting Y our Components —Continued •T o enjoy Dolby Digital and DTS, use connection or . If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiv er to the A V receiv er and use its tuner to listen to TV programs through the A V receiv er (see pages 23 and 25). Connecting a TV or Projector Conne[...]

21 Connecting Y our Components —Continued •T o enjoy Dolby Digital and DTS, use connection or . • If your D VD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection . Connecting a D VD pla yer Connection A V receiver Signal flow D VD player Picture qualit[...]

22 Connecting Y our Components —Continued Hooking Up the Multichannel Input If your D VD player supports multichannel audio formats such as D VD-Audio and SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel input. Use a multichannel analog audio cable, or sev eral normal audio cables, to [...]

23 Connecting Y our Components —Continued W ith this hookup, you can use the tuner in your VCR or D VR to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •T o enjoy Dolby Digital and DTS, use connection or . Connecting a VCR or DVR f or Playback Connection A V receiver Signal flow VCR[...]

24 Connecting Y our Components —Continued Notes: • The A V receiv er must be turned on for recording. Recording is not possible while it’ s on Standby . • If you want to record directly from your TV or another video source without going through the A V receiv er , connect the audio and video outputs from your TV or other video component dir[...]

25 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •T o enjoy Dolby Digital and DTS, use connection or . Connecting a Satellite, Cable, or T errestrial Set-top box or Other Video [...]

26 Connecting Y our Components —Continued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, D VD players, set-top boxes, and other video components. Until no w , sev eral separate video and audio cables hav e been requ[...]

27 Connecting Y our Components —Continued If you hav e an HDMI-compatible player , you can connect it to the A V receiv er with an HDMI cable. ■ A udio Signals • Audio and video signals receiv ed via inputs other than the HDMI IN jacks are not output by the HDMI OUT . • Audio and video signals receiv ed via the HDMI IN jacks are output only[...]

28 Connecting Y our Components —Continued Connecting a Camcorder , Game Console, or Other Device Connection A V receiver Signal flow Camcorder or console A UX INPUT VIDEO ⇐ Composite video output A UX INPUT L-A UDIO-R ⇐ Analog audio L/R output SETUP SETUP MIC VIDEO L AUDIO R A UX INPUT ENTER RETURN TUNING PRESET MASTER VOLUME VIDEO OUT AUDIO[...]

29 Connecting Y our Components —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp •T o connect the CD player digitally , use connection or . ■ T urntable (MM) with no Phono Preamp Built- in A phono preamp is necessary to connect a turntable that doesn’t ha ve a phono preamp b uilt-in. ■ T urntable with an MC (Mo ving [...]

30 Connecting Y our Components —Continued •T o connect the recorder digitally for playback, use connections and , or and . Connecting a Cassette, CDR, MiniDisc, or DA T Recorder Connection A V receiver Signal flow Cassette, CDR, MD , or D A T recorder T APE IN L/R T APE OUT L/R ⇐ ⇒ Analog audio L/R output Analog audio L/R input DIGIT AL IN[...]

31 Connecting Y our Components —Continued ■ If Y our iPod Supports Video: Connect your RI Dock’ s audio output jacks to the AV receiv er’ s CBL/SA T IN L/R jacks, and connect its video output jack to the A V receiver’ s CBL/SA T IN V jack. If you hav e an Onkyo DS-A1 RI Dock, connect its video output jack to the A V receiv er’ s CBL/SA [...]

32 Connecting Y our Components —Continued W ith (Remote Interactiv e), you can use the following special functions: Auto P ower On/Standby When you start playback on a component connected via , if the A V receiver is on Standby , it will automatically turn on and select that component as the input source. Similarly , when the A V receiv er is set[...]

33 T urning On the A V Receiver ON/STANDBY STANDBY PURE AUDIO CINEMA FILTER T ONE MOVIE/TV MUSIC GAME DISPLAY RT/PTY/TP MEMORY CLEAR DIGITAL INPUT TUNING MODE LATE NIGHT PHONES MULTI CH PURE AUDIO DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP SETUP MIC VIDEO L AUDIO R A UX INPUT ENTER RETURN TUNING PRESET MASTER VOLUME AV RECEIVER HT-R518 ON/STANDBY [...]

34 Fir st Time Setup This section explains the settings that you need to make before using the A V recei ver for the very first time. W ith the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers con- nected, their size for purposes of bass management, optimum crossov er frequencies to the subwoofer (if pre[...]

35 First Time Setup —Continued Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 63) will be set to “ Audyssey . ” • When the automatic speaker setup is complete, the Audyssey Dynamic EQ settings (page 57) will be set to “On. ” Error Messa ges While the automatic speaker setup is in progress, one of t[...]

36 First Time Setup —Continued Changing the Speaker Settings Manuall y If you wish to make changes to the settings found during the automatic speaker setup, follo w the directions on pages 59–63. Using a P owered Subw oofer If you’ re using a po wered subwoofer , as it outputs very low-frequenc y sound and its position is usually low do wn, i[...]

37 First Time Setup —Continued If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector . For example, if you connect your D VD player to COMPONENT VIDEO IN 2, you must assign COM- PONENT VIDEO IN 2 to the D VD input selector . By default, the D VD input selector is assigned to COM- PONENT VIDEO IN[...]

38 First Time Setup —Continued If you connect an -capable Onkyo MiniDisc recorder , CD recorder , or RI Dock to the T APE IN/OUT jacks, or connect an RI Dock to the CBL/SA T jacks, for to work properly , you must change this setting. This setting can only be changed on the A V receiver. Note: • DOCK can be selected for the T APE input selector [...]

39 Pla ying Y our A V Components Basic A V Receiver Operation ON/STANDBY STANDBY PURE AUDIO CINEMA FILTER T ONE MOVIE/TV MUSIC GAME DISPLAY RT/PTY/TP MEMORY CLEAR DIGITAL INPUT TUNING MODE LATE NIGHT PHONES MULTI CH PURE AUDIO DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP SETUP MIC VIDEO L AUDIO R A UX INPUT ENTER RETURN TUNING PRESET MASTER VOLUME A[...]

40 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V receiver. To unmute the A V receiv er, press the remote control- ler’ s [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indic[...]

41 Common Functions —Continued 7 For pri vate listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the A V receiver’ s PHONES jack. Notes: •A lw ays turn down the v olume before connecting your headphones. • While the headphones plug is inserted in the PHONES jack, the speakers are turned of f. • When you connec[...]

42 Common Functions —Continued The following table sho ws the display indicator for each digital signal format. Normally , the A V receiv er detects the format of digital input signals automatically . Howe ver , if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually . • If th[...]

43 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. ■ M[...]

44 Listening to the Radio —Continued ■ T uning into Stations b y Frequency Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Displaying AM/FM Radio Inf ormation 1 Press the [TUNER] button repeat- edly to select AM or FM, followed by the [D.TUN] b utton. (Actual display depends on country .) 2 Within 8 seco[...]

45 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM and FM radio stations. Deleting Presets Selecting Presets Presetting AM/FM Stations 1 T une into the AM or FM station you want to store as a preset. 2 Press the [MEMOR Y] b utton. The preset number flashes. 3 While the preset number is flash- ing [...]

46 Listening to the Radio —Continued RDS only works in areas where RDS broadcasts are av ailable. When tuned to an RDS station, the RDS indi- cator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was de veloped by the European Broadcasting Union (EBU) and is a vail- able in m[...]

47 Listening to the Radio —Continued Displaying Radio T ext (R T) When tuned to an RDS station that’ s broadcasting text information, the text can be displayed. Notes: • The message “W aiting” may appear while the A V receiv er waits for the R T information. • If the message “No T ext Data” appears on the display , no R T informatio[...]

48 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 52. Selecting on the A V Receiver ■ [PURE A UDIO] b utton This button selects the Pure Audio listening mode. When this mode is selected, the A V receiver’ s dis- play is turned off and only the HDMI outputs output video signals. [...]

49 Using the Listening Modes —Continued Analog and PCM Sources Listening Modes A v ailable f or Each Source Format Button Source f ormat PCM Multi channel Analog 32–96kHz *1 *1. 32/44.1/48/88.2/96kHz Media Listening Mode CD, TV , radio, D VD [PURE A UDIO] Pure Audio ✔✔ [MO VIE/TV] Mono ✔ Dolby PLII Mo vie ✔ Neo:6 Cinema ✔ MonoMovie *2[...]

50 Using the Listening Modes —Continued Dolby Digital Sour ces Button Source f ormat Dolby Digital Multichannel 2ch Mono/Multiplex Media Listening Mode DV D, DTV , etc. [PURE A UDIO] Pure Audio ✔✔✔ [MO VIE/TV] Mono ✔✔✔ DolbyDigital ✔ Dolby PLII Mo vie ✔ Neo:6 Cinema ✔ MonoMovie *1 *1. Available only when using surround speakers.[...]

51 Using the Listening Modes —Continued DTS Sources Button Source f ormat DTS, DTS 96/24 DTS Discrete/Matrix Multichannel 2ch Mono/Multiplex Media Listening Mode DV D, CD, etc. D VD, CD , etc. [PURE A UDIO] Pure Audio ✔✔✔ ✔ [MO VIE/TV] Mono ✔✔✔ ✔ DTS, DTS 96/24 ✔✔ Dolby PLII Mo vie ✔ Neo:6 Cinema ✔ MonoMovie *1 *2 *1. Avai[...]

52 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Pure Audio In this mode, the display and video circuitry are turned off, minimizing possible noise sources for the ultimate in high-fidelity reprodu[...]

53 Using the Listening Modes —Continued Onky o Original DSP Modes Mono Movie This mode is suitable for old movies and other mono sources. The center speak er outputs the sound as it is, while rev erb is applied to the sound output by the other speakers, gi ving presence to ev en mono material. Orchestra Suitable for classical or operatic music, t[...]

54 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. • Sources connected to a digi[...]

55 Adjusting the Listening Modes W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. The Audio Adjust settings are explained belo w . Multiplex/Mono Settings Multiplex ■ Input (Mux) This setting determines which channel of a stereo multi- plex source is output. Use it to select audio channels o[...]

56 Adjusting the Listening Modes —Continued ■ Center Width W ith this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic II Music listening mode. Normally , if you’ re using a cen- ter speaker , the center channel sound is output by only the center speaker . (If you’ re not using a center s[...]

57 Adjusting the Listening Modes —Continued Y ou can change various audio settings by pressing the [A UDIO] button. The Audio Adjust settings are explained belo w . T one Contr ol Settings Y ou can adjust the bass and treble for the front speakers, e xcept when the Direct or Pure Audio listening mode is selected. ■ Bass Y ou can boost or cut lo[...]

58 Adjusting the Listening Modes —Continued Speaker Levels Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiv er is set to Standby . ■ Subwoof er Y ou can adjust the lev el from –15 dB to +12 dB. ■ Center Y ou can adjust the lev el from –12 dB to +[...]

59 Ad v anced Setup This section explains ho w to check the speaker settings and how to set them manually , which is useful if you change a speaker after performing the automatic speaker setup. Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 34). Speaker Configuration This section explains ho w [...]

60 Adv anced Setup —Continued Note: • These settings cannot be changed while headphones are connected or the multichannel D VD input is being used. Crosso ver Frequency This setting only applies to the speakers that you speci- fied as Small in the “Speaker Configuration” on page 59. To get the best bass performance from your speaker sys- [...]

61 Adv anced Setup —Continued Speaker Distance W ith these settings, you can specify the distance from each speaker to the listening position. Notes: • The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Left distance. For e xample, if the Left distance is set to 20 ft. (6 m), the Center and Subwoofer distanc[...]

62 Adv anced Setup —Continued Speaker Levels Y ou can set the volume le vel of each speaker so that all speakers can be heard equally at the listening position. Note: • The speaker le vels cannot be adjusted while a pair of headphones is connected or the A V receiver is muted. 1 Press the [RECEIVER] REMO TE MODE button, followed b y the [SETUP][...]

63 Adv anced Setup —Continued Equalizer Settings Here you can adjust the tone of individual speak ers. T o set the volume of indi vidual speakers, see page 62. Notes: • The front, center , and surround speakers can be adjusted at 80Hz, 250Hz, 800Hz, 2500Hz, and 8000Hz. The subw oofer can be adjusted at 40Hz, 80Hz, and 160Hz. • While the Direc[...]

64 Contr olling Other Components Y ou can control your D VD player , CD player , and other components with the A V receiver’ s remote controller . To control another component, you must first enter that component’ s remote control code to a REMOTE MODE button. This section explains ho w to enter remote control codes and how to control your oth[...]

65 Controlling Other Components —Continued Remote Control Codes f or Onky o Components Connected via Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example. If you want to control an Onk[...]

66 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your D VD player (HD D VD, Blu-ray , or TV/D VD combination), you can control your player with the following b uttons. The [D VD] REMO TE MODE button is preprogrammed with the remote control code for controllin[...]

67 Controlling Other Components —Continued T PLA Y MODE button Selects play modes on components with selectable play modes. U CLR button Cancels functions and clears entered numbers. Note: • If you enter the remote control code for a HD D VD or Blu-ray player that has A, B, C, and D buttons, the [SEARCH], [REPEA T], [RANDOM], and [PLA Y MODE] b[...]

68 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your sat- ellite receiv er , cable receiv er , or D VD recorder (DBS/PVR combination or cable/PVR combination), you can control your player with the following b uttons. F or details on entering a remote control[...]

69 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your CD player , CD recorder , or MD player , you can control your player with the following b uttons. The [CD] REMO TE MODE button is preprogrammed with the remote control code for controlling an Onkyo CD play[...]

70 Controlling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your RI Dock, you can control your iPod in the RI Dock with the following b uttons. The [DOCK] REMO TE MODE button is prepro- grammed with the remote control code for controlling an RI Dock when used with an co[...]

71 Controlling Other Components —Continued P Fast Forwar d [ ] button Press and hold to fast forward. Q Stop [ ] button Stops playback and displays a menu. R PLA Y MODE button Selects play modes on components with selectable play modes. W orks as a Resume button when used with a DS-A2 RI Dock. S RANDOM button* Used with the shuffle function. * B[...]

72 Controlling Other Components —Continued By pressing the [TV] REMO TE MODE button that’ s been programmed with the remote control code for your TV (TV/D VD combination or TV/VCR combination), you can control your TV with the follo wing buttons. F or details on entering a remote control code for a dif fer- ent component, see page 64. A ON/ST A[...]

73 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact your Onkyo dealer . Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all outlet, wait 5 seco[...]

74 Tr oubleshooting —Continued There’ s no sound with a cer tain signal format • Check the digital audio output setting on the source component. On some game consoles, such as those that can play D VDs, the default setting is of f. •W ith some D VD-V ideo discs, you need to select an audio format from a menu or with the A UDIO button on you[...]

75 Tr oubleshooting —Continued The remote controller doesn’t w ork • Make sure that the batteries are installed with the cor - rect polarity (page 12). • Make sure that the remote controller is not too far aw ay from the A V receiver and there’ s no obstruction between the remote controller and the A V receiver’ s remote control sensor [...]

76 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Control T erminal Specifications and features are subject to change without notice. HT -R518 Rated Output Power 7 ch × 130 W at 8 ohms, 1kHz, 1 ch dri ven (IEC) Dynamic Power 210 W (3[...]

77 Memo HT-R518_En.book Page 77 Tuesday, March 11, 2008 11:31 AM[...]

78 Memo HT-R518_En.book Page 78 Tuesday, March 11, 2008 11:31 AM[...]

79 Memo HT-R518_En.book Page 79 Tuesday, March 11, 2008 11:31 AM[...]

80 Memo SN 29344662 I0803-1 (C) Copyright 2008 ONKY O CORPORA TION Japan. All rights reser ved. http://www.onky o.com/ HOMEP AGE * 2 9 3 4 4 6 6 2 * Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A[...]