Pelco IV SE manual

INSTALLATION/OPERATION C3412M (9/06) Spectra ® IV and Spectra ® IV SE Series Dome Drives[...]

[...]

C3412M (9/06) 3 Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

4 C3412M (9/06) Dome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

C3412M (9/06) 5 Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Edit Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

6 C3412M (9/06) W elcome Thank you for purchasing Pelco’ s premier integrated dome system, Spectra ® IV/Spectra ® IV SE. Y our new system features a high resolution camera/optics package with programmable dome drive software. This manual is designed primarily to be a reference tool for the operation and programming of your system. Inside you wi[...]

C3412M (9/06) 7 Installation NOTE: This manual contains installation instructions only for the Spectra IV/Spectra IV SE dome drive. For complete installation instructions for a Spectra IV/Spectra IV SE dome system, refer to the installation manual shipped with the back box. SWITCH SETTINGS Before installing the dome drive, configure the receiver a[...]

8 C3412M (9/06) CM9502 Setting If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position. Vicon System The Vicon protocol is not currently available. SW2-3 is reserved for future use. SW2 SWITCHES 4-5 – SERIAL PORT SETTINGS 2 Wire Setting (RS-485) SW2-4 should be set to the ON position if a two-wire serial port connectio[...]

C3412M (9/06) 9 DOME DRIVE INSTALLATION Install the dome drive. Line up the blue and red tabs with the blue and red arrows on the hinged door inside the back box. Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click into place. Refer to Figure 2. T o use your dome system, refer t[...]

10 C3412M (9/06) T able A. Switch Settings for SW1 P-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF O[...]

C3412M (9/06) 11 T able B. Switch Settings for SW1 D-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON O[...]

12 C3412M (9/06) 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF ON OFF OFF 42 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON OFF OFF 44 OFF OFF ON ON OFF ON OFF OFF 45 ON OFF ON ON OFF ON OFF OFF 46 OFF ON ON O[...]

C3412M (9/06) 13 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF[...]

14 C3412M (9/06) 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON OFF 112 OFF OFF OFF OFF ON ON ON OFF 113 ON OFF OFF OFF ON ON ON OFF 114 OFF ON OFF OFF ON ON ON OFF 115 ON ON OFF OFF ON ON ON OFF 116 OFF OFF ON OFF[...]

C3412M (9/06) 15 141 ON OFF ON ON OFF OFF OFF ON 142 OFF ON ON ON OFF OFF OFF ON 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ON[...]

16 C3412M (9/06) 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON OFF ON 182 OFF ON ON OFF ON ON OFF ON 183 ON ON ON OFF ON ON OFF ON 184 OFF OFF OFF ON ON ON OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF ON [...]

C3412M (9/06) 17 211 ON ON OFF OFF ON OFF ON ON 212 OFF OFF ON OFF ON OFF ON ON 213 ON OFF ON OFF ON OFF ON ON 214 OFF ON ON OFF ON OFF ON ON 215 ON ON ON OFF ON OFF ON ON 216 OFF OFF OFF ON ON OFF ON ON 217 ON OFF OFF ON ON OFF ON ON 218 OFF ON OFF ON ON OFF ON ON 219 ON ON OFF ON ON OFF ON ON 220 OFF OFF ON ON ON OFF ON ON 221 ON OFF ON ON ON OFF[...]

18 C3412M (9/06) 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON T able B. Switch Settings for SW1 D-T ype Control (Continued) SPEC[...]

C3412M (9/06) 19 Getting Started Once installed, apply power to the Spectra IV/Spectra IV SE dome system. The system will start a configuration sequence. When configuration is done, the following information is displayed: Pelco Spectra IV/Spectra IV SE V ersion X.XX D Address: 1 P Address: 2 Comm 2400, N, 8, 1 CONFIGURE DONE This information will[...]

20 C3412M (9/06) How to Operate Y our Dome System Operation How to Control Pan and T ilt Move joystick or press the direction keys left/right and up/down. Zoom Far T o zoom far , do the following: 1. Press the Zoom T ele button or turn the joystick clockwise until zoom stops at the 32X zoom limit. 2. Release the button or joystick for one second. 3[...]

C3412M (9/06) 21 QUICK PROGRAMMING GUIDE Access main menu (preset 95). See the Accessing Main Menu (Preset 95) section. Use the joystick to position the cursor beside menu selection. NOTE: If your controller does not have a joystick, use the up or down key . Press Iris Open, the submenu/cursor moves to the right. Move the joystick up or down to vie[...]

22 C3412M (9/06) CM9500 1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key . The main menu appears. 2. Highlight SETUP in the main menu and press the SELECT key . 3. Highlight CAM in the Setup menu and press the SELECT key . 4. Highlight PRESET in the Camera menu and press the SELECT key . 5. Enter 95 and press th[...]

C3412M (9/06) 23 NET300/NET350/NET4001A 1. Check the Set box. 2. Click the preset 95 button. The main menu appears. WS5050 1. Right-click in the video pane of the Spectra IV/Spectra IV SE dome system. 2. Click Preset and then click Select Preset. 3. Enter 95 and then click OK. VCD5000 1. Enter 95 for the preset action. The shortcuts menu appears. 2[...]

24 C3412M (9/06) 16X LowLight Color Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV DOME DRIVE MODEL XX-XXXX SERIAL # XXXXXXXXXXXXXX BACK BOX MEMORY AV AILABLE SOFTWARE VERSION XX.X FONT VERSION XX.X COMM D ADDRESS XXXXXXXXXX FON[...]

C3412M (9/06) 25 PRESET NUMBER 1 PRESETS PA TTERNS LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY . , - / abcdefghij klmnopqrst uvwxyz# &: * EDIT THE PASSWORD DOME SETTINGS TIME BASE TIME FORMA T SET TIME DA TE FORMAT SET DA TE DA YLIGHT SAVINGS INTERNAL CLOCK[...]

26 C3412M (9/06) 22X EXview LowLight Black-White Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV SHUTTER SPEED AUTO AGC LIMIT 28 AUTO IRIS AUTO AUTO IRIS LEVEL 66 AUTO IRIS PEAK AUTO SHARPNESS 8 ON 26 OFF HIGH SHARPNESS LEVEL BAC[...]

C3412M (9/06) 27 LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALARM CONT ACT ALARMS ALARM SETTINGS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .,-/ abcdefghij klmnopqrst uvwxyz# &: * EDIT THE PASSWORD <CAMERA> <MOTION&g[...]

28 C3412M (9/06) 22X EXview LowLight Color Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV SHUTTER SPEED AUTO AGC LIMIT 28 AUTO IRIS AUTO AUTO IRIS LEVEL 66 AUTO IRIS PEAK AUTO SHARPNESS 8 ON 26 ON 482 678 OFF HIGH SHARPNESS LEVE[...]

C3412M (9/06) 29 LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALARM CONT ACT ALARMS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .,-/ abcdefghij klmnopqrst uvwxyz# &: * EDIT THE PASSWORD <CAMERA> <MOTION> <POWER UP[...]

30 C3412M (9/06) 23X LowLight Day/Night Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV SHUTTER SPEED AUTO AGC LIMIT 28 AUTO IRIS AUTO AUTO IRIS LEVEL 66 AUTO IRIS PEAK AUTO SHARPNESS 8 ON 26 ON 482 678 OFF HIGH OFF SHARPNESS LEV[...]

C3412M (9/06) 31 ALARM CONT ACT ALARMS ENABLE TITLE TEXT <EDIT TITLE TEXT> TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXY .,-/ abcdefghij klmnopqrst uvwxyz# &: * EDIT THE PASSWORD <CAMERA> <MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PA TTERNS> <ZONES> <WINDOW BLANKING> <ALARMS> <A[...]

32 C3412M (9/06) 35X LowLight Day/Night Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> ACK ALERT* RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SPECTRA IV ADVANCED SETTINGS AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME (MINUTES) 0 PARK ACTION NONE SCAN SPEED DEG/S PRESET FREEZE FRAME 25 AUTO ON LIM[...]

C3412M (9/06) 33 DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION SENSITIITY 0 MEDIUM 0 MEDIUM 0 MEDIUM DETECTION AREA 3 LOCA TION SENSITIVITY DETECTION AREA 4 LOCA TION SENSITIVITY EDIT DETECTION AREAS LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALARM [...]

34 C3412M (9/06) Language The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Russian, Polish, T urkish, and Czechoslovakian. The factory default language is English. T o change the display language: 1. Use the joystick to position the cursor beside LANGUAGE. 2. Pres[...]

C3412M (9/06) 35 System Information The System Information screen displays dome drive model, software version, available memory , and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only . Use the following steps to display the System Information screen: 1. Use the joystick to position[...]

36 C3412M (9/06) Display Setup Display setup allows you to program how labels are displayed on the monitor . The following labels are available: PRESET LABEL Identifies preset. ZONE LABEL Identifies zone. ZOOM Identifies the amount of magnification. AZIMUTH 1 /ELEVATION 2 Amount of pan from 0° and the amount of tilt from 0° horizontal. DIRECT[...]

C3412M (9/06) 37 LABEL POSITIONS Labels can be placed anywhere on the monitor . This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: PRESET LABEL ZONE LABEL ALARM 1 ZOOM RA TIO - XXX.XX AZIMUTH 1 /ELEV A TION 2 - XXX°/-XX° DIRECTION - NE ALERT MESSAGE 3 * TITLE TEXT T o [...]

38 C3412M (9/06) Dome Settings CAMERA T YPE OF LIGHTING (Does not apply to 16X or 23X models.) Pelco has calibrated settings that optimize the white balance and the picture for indoor and outdoor lighting conditions. There are two settings: OUTDOOR (default) INDOOR AUTO FOCUS Auto focus allows the lens to remain in focus during zoom-in, zoom-out, a[...]

C3412M (9/06) 39 ZOOM LIMIT Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The settings vary depending on camera model. 16X (Models DD4TC16 and DD4TC16-X) The default setting is 32X. Cameras with 128X zoom (16X optical zoom and 8X digital zoom) can be set for 16X, 32X, 64X, or 128X. 22X (Models DD4M22, DD4M22-X,[...]

40 C3412M (9/06) ZOOM SPEED Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 16X, 22X, 23X, or 35X optical zoom. Available zoom speed settings for 16X models include the following: HIGH 1.9 seconds MEDIUM (default) 3.6 seconds LOW 6.0 seconds Available zoom speed settings for 23X models include the followin[...]

C3412M (9/06) 41 IR CUT FILTER (Applies only to 23X and 35X models.) The 23X and 35X cameras have two modes of operation: color , and black-white. Y ou can increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut filter). Color mode is preferred in normal lighting conditions. The following are the settings[...]

42 C3412M (9/06) ADVANCED CAMERA SETTINGS SHUTTER SPEED Shutter speed is the duration of the electronic shutter . Program shutter speed to operate automatically (Auto) or manually (Numeric V alue). AUTO (default) The electronic shutter speed is set automatically by the amount of light sensed by the camera. NUMERIC V ALUE Spectra IV/Spectra IV SE do[...]

C3412M (9/06) 43 AUTO IRIS Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user -defined level. OFF Auto iris is disabled, and control is always manual. AUTO (default) The iris is adjusted automatically to produce a constant[...]

44 C3412M (9/06) AUTO SHARPNESS Auto sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. There are two settings: ON (default) The camera automatically maintains a normal sharpness mode. OFF The sharpness of the picture is set manually by programming the sharpness level. Sharpness [...]

C3412M (9/06) 45 BACKLIGHT COMPENSATION (BLC) If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to [...]

46 C3412M (9/06) VIDEO LEVEL Set the video output to one of the following: NORMAL 1.0 volt peak-to-peak HIGH (default setting) 1.2 volt peak-to-peak to compensate for losses in video cable. WIDE DYNAMIC RANGE (Applies only to 23X and 35X models.) Wide dynamic range (WDR) balances the brightest and darkest sections of a scene to produce a picture th[...]

C3412M (9/06) 47 ELECTRONIC IMAGE STABILIZATION (Applies only to 35X models.) Electronic image stabilization is a feature of the camera that can compensate for some forms of external influences. In all cases, care should be taken to make sure that any dome system is mounted to a rigid location. In the event that vibration is introduced to the dome[...]

48 C3412M (9/06) MOTION SETTINGS AUTO FLIP When the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joystick contro[...]

C3412M (9/06) 49 PARK T IME This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity . Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero. Park Action This feature will define the activity [...]

50 C3412M (9/06) SCAN SPEED Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is adjustable from 1 to 40 degrees per second through the programming menu. The default setting is 25 degrees per second. PRESET FREEZE FRAME This feature freezes the scene on the monitor when going to a preset. This allows for sm[...]

C3412M (9/06) 51 LIMIT STOPS Limit stops are programmable stops that limit the pan range of the dome. There must be two limits, a left and a right, to define an area. There are two types of limit stops: MANUAL A manual (joystick) pan operation stops when a limit stop is reached. SCAN The dome reverses direction during random, frame, or auto scanni[...]

52 C3412M (9/06) AZIMUTH ZERO Azimuth is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the 0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point. T o program azimuth zero: 1. Use the joystick to position the cursor beside SET AZ[...]

C3412M (9/06) 53 POWER UP POWER UP ACTION This setting defines a specific activity (scan, preset, pattern) to be performed in the event the power to the dome is cycled. The following settings are available: NONE No action. AUTO (default) The dome resumes its prior activity or direction before the power outage. AUTO SCAN Dome starts auto scan oper[...]

54 C3412M (9/06) LINE SYNC Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: Spectra IV and Spectra IV SE dome systems automatically sense V-Sync input. No line sync setup is required for Pelco control systems that provide a V-Sync signal. For matrix systems that do not output V-Syn[...]

C3412M (9/06) 55 PRESETS NOTE: The number of programmable presets available is limited by the model of the back box you are using. If you are using an older model back box, you may not have access to all of the available presets. Refer to the table below for a list of back boxes and the presets available for each. The Spectra IV dome system, which [...]

56 C3412M (9/06) NOTE: For American Dynamics controllers with only 32 presets, switch SW2-1 on the dome drive to the ON position. When SW2-1 is ON, preset 99 becomes 32 92 becomes 25 98 becomes 31 91 becomes 24 97 becomes 30 90 becomes 23 96 becomes 29 89 becomes 22 95 becomes 28 88 becomes 21 93 becomes 26 If the limit stops are turned off, preset[...]

C3412M (9/06) 57 4. Edit preset camera settings: a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS. b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor . Refer to the Camera and Advanced Camera Settings sections of this manual to change preset camera settings. c. T o edit the camera settings schedule, use[...]

58 C3412M (9/06) ENABLE MOTION DETECTION (Applies only to 23X and 35X models.) The following are the settings for motion detection: OFF (default) Motion detection is turned off (disabled). ON Motion detection is turned on (enabled). NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second. EDIT DETECTION AREAS [...]

C3412M (9/06) 59 NOTE: Motion detection is not guaranteed to catch 100% of activity . EDIT DETECTION AREAS DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 3 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 4 LOCA TION 0 SENSITIVITY MEDIUM BACK EXIT MOTION DETECTION AREAS[...]

60 C3412M (9/06) ACTIVATE AUX COMMAND (Applies only to 23X and 35X models.) Motion detection can be programmed to trigger an auxiliary command when motion is detected. The following are the settings for ACTIV A TE AUX: OFF (default) Motion detection will not trigger an AUX command. 1 T riggers a command to AUX 1. 2 T riggers a command to AUX 2. AUX[...]

C3412M (9/06) 61 PATTERNS A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park, event, or power -up). Both 16X and 23X models have one user -defined pattern available. The 22X and 35X models can handle up to e[...]

62 C3412M (9/06) ZONES A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra 4 and Spectra IV SE dome systems are capable of eight zones, each with a 20-character label. T o program a zone: 1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the cursor moves to the right. [...]

C3412M (9/06) 63 WINDOW BLANKING Window blanking allows a user to program four -sided areas that cannot be viewed by the operator of the dome system. A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. The 16X and 23X models have one user -defined window blank available. The 2[...]

64 C3412M (9/06) 6. The blanked area can be programmed to turn on or off at a specified zoom point. T o set the zoom point: a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open. b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point. NOTES: • Since the area[...]

C3412M (9/06) 65 BLANK ALL ABOVE/BLANK ALL BELOW The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas. These settings are ideal for applications where a complete pan location needs to be blanked. Blank All Above Blanks everything above a user -defined tilt angle. A blanked band will appear at the [...]

66 C3412M (9/06) ALARMS The Spectra IV SE dome systems have seven alarm inputs that can be programmed as high, medium, or low priority . When an alarm is received, an input signal to the dome triggers the user - defined action (go to preset, run pattern, etc.) programmed for the alarm. NOTE: Refer to the notation in step 6 for the limited alarm fe[...]

C3412M (9/06) 67 3. Select the alarm priority: a. Use the joystick to position the cursor beside ALARM PRIORITY . b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the available selections. Available settings include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities are active at [...]

68 C3412M (9/06) 5. Set the auxiliary to activate: a. Use the joystick to position the cursor beside ACTIV A TE AUX. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the following available selections. NO (default) Not activated. 1 An alarm action will close AUX 1. 2 An alarm action will close AUX 2. d. Pre[...]

C3412M (9/06) 69 AUX NOTE: The auxiliary feature is functional and available for 16X and 23X models only if the dome drive is installed in a Spectra III SE or Spectra IV SE back box. An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate. An auxiliary output is programmable to trigger from an [...]

70 C3412M (9/06) T ITLE T EXT T itle text is the label used to identify the camera viewed on the monitor . Up to 20 characters can be used for a title. T o edit the title text label, do the following: 1. Use the joystick to position the cursor beside EDIT TITLE TEXT . 2. Press Iris Open. The following appears on the monitor: 3. Use the joystick to [...]

C3412M (9/06) 71 ALERT NOTE: The Alert option applies only to Pressurized Spectra IV dome systems. Spectra 4 systems that are not pressurized will not display this menu item. Sensors strategically placed inside the pressurized dome system continually monitor pressure, temperature, and dew point. If internal conditions reach unacceptable levels, an [...]

72 C3412M (9/06) ACK ACTION Acknowledge action programs the alert label behavior after the alert condition has been acknowledged. The following settings are available for acknowlegde: AL W A YS ON The alert label is displayed until alert conditions are cleared. OFF 8 HRS The alert label is turned off for 8 hours. Label returns after 8 hours if the [...]

C3412M (9/06) 73 CLEAR Use this setting to clear user -defined settings or return the dome to factory default settings. The following are the available settings: ALL ZONES Clears all zones. T o clear a single zone, refer to the Zones section. ALL PRESETS Clears all presets. T o clear a single preset, refer to the Presets section. ALL P A TTERNS Cl[...]

74 C3412M (9/06) PASSWORD Spectra IV and Spectra IV SE feature password protection to prevent unauthorized changes to the dome settings. An operator can open the System Information and Display Setup screens, but cannot access any of the dome settings menus. Controller/keyboard commands cannot override password-protected settings. If a keyboard is u[...]

C3412M (9/06) 75 CLOCK The clock is used to program the current date and time. The date and time set in the Clock menu is used to program events. The date and time can also be displayed on the monitor when the menus are not being accessed. T o program the clock, do the following: 1. Use the joystick to position the cursor beside TIME BASE. Press Ir[...]

76 C3412M (9/06) 7. If FIXED DA TE was selected, the following appears on the monitor: a. Use the joystick to position the cursor beside TIME SHIFT . Press Iris Open. Scroll through the options until the desired selection appears. Press Iris Open to select the time shift. b. Use the joystick to position the cursor beside the start date MONTH. Press[...]

C3412M (9/06) 77 8. If RELA TIVE DA TE was selected, the following appears on the monitor: Follow the instructions in step 7 for FIXED DA TE, adding WEEK. CLOCK TIME BASE INTERNAL CLOCK TIME FORMA T 12 HOUR SET TIME 00:00 AM DA TE FORMA T MM/DD/YYYY SET DA TE 00/00/0000 DA YLIGHT SAVINGS RELA TIVE DA TE TIME SHIFT 1 HOUR ST ART DA TE MONTH APRIL WE[...]

78 C3412M (9/06) EVENT An event is a preprogrammed camera, park, scan, preset, pattern, window blanking, alarm, or auxiliary function that can be performed automatically at a specific date and time. For example, suppose a camera is set to run in a continuous pattern that scans a parking lot during business hours Monday through Friday . On Saturday[...]

C3412M (9/06) 79 EDIT EVENT LABEL Use the following steps to edit the event label. 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. The following appears on the monitor: 3. Use the joystick to position the cursor beside a character . Press Iris Open to enter selection. T o clear a character , position the curs[...]

80 C3412M (9/06) EDIT EVENT Use the following steps to edit an event. 1. Use the joystick to position the cursor beside EDIT EVENT . 2. Press Iris Open. The following appears on the monitor: a. Use the joystick to position the cursor beside EVENT ACTIVE. Press Iris Open. Scroll to select NO to leave the event inactive or YES to activate the event. [...]

C3412M (9/06) 81 CLEAR EVENT T o clear an event: 1. Use the joystick to position the cursor beside CLEAR EVENT . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST EVENT T o list events: 1. Use the joystick to position the cursor beside LIST EVENT . 2. Press Iris Open. 3. All programmed events will be listed. HOLIDAY Use t[...]

82 C3412M (9/06) EDIT HOLIDAY Use the following steps to edit a holiday: 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. 3. Use the joystick to position the cursor beside OCCURRENCE. Press Iris Open. The following are the settings for Occurrence: FIXED DA TE Holiday occurs on the same date each year . RELA TI[...]

C3412M (9/06) 83 CLEAR HOLIDAY T o clear a holiday: 1. Use the joystick to position the cursor beside CLEAR HOLIDA Y . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST HOLIDAYS T o list events: 1. Use the joystick to position the cursor beside LIST HOLIDA YS. 2. Press Iris Open. 3. All programmed holidays will be listed.[...]

84 C3412M (9/06) SCHEDULED EVENTS Use this page to record scheduled events. ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ _______[...]

C3412M (9/06) 85 Reset, Cycle Power , Reboot RESET CAMERA Use this function to reset all camera settings to factory default parameters. CYCLE CAMERA POWER If the camera is not operating or if you lose camera control, cycle camera power . Cycling camera power resets the camera but does not change any saved camera settings. REBOOT SYSTEM Reboot the s[...]

86 C3412M (9/06) Software/Language File Upload The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations. Field service tools include Pelco’ s remote monitor kit (IPS-RMK), remote data port box[...]

C3412M (9/06) 87 Suggested Preventative Maintenance The Spectra IV and Spectra IV SE dome systems do not require any special maintenance. Occasionally , dust may build up on the inside or the outside of the dome. If this occurs, turn power to the unit off and remove the lower dome from the back box. Remove the dust from the lower dome using compres[...]

88 C3412M (9/06) Specifications 16X MODELS DD4TC16 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch interline transfer CCD Effective Pixels 768 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.4 (f=4~64 mm optical, 16X optical zoom, 8X digital zoom) Zoom Speed (optical range) 1.9/3.6/6.0 seconds Horizontal Angle o[...]

C3412M (9/06) 89 22X MODELS (MONOCHROME) DD4M22 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >500 TV lines Lens F1.6 (f=4~88 mm optical, 22X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.4/3.9/6.3 seconds Horizontal Angle of View 47° at 4 mm wi[...]

90 C3412M (9/06) 22X MODELS (COLOR) DD4C22 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=4~88 mm optical, 22X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.4/3.9/6.3 seconds Horizontal Angle of View 47° at 4 mm wide zo[...]

C3412M (9/06) 91 23X MODELS DD4CBW23 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 494 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=3.6~82.8 mm optical, 23X optical zoom, 12X digital zoom) Zoom Speed (optical range) 2.9/4.2/5.8 seconds Horizontal Angle of View 54° at 3.6 mm wide zo[...]

92 C3412M (9/06) DD4CBW23-X Signal Format P AL Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 582 (V) Horizontal Resolution >470 TV lines Lens F1.6 (f=3.6~82.8 mm optical, 23X optical zoom, 12X digital zoom) Zoom Speed 2.9/4.2/5.8 seconds Horizontal Angle of View 54° at 3.6 mm wide zoom; 2.5° at 82.8 mm tele[...]

C3412M (9/06) 93 35X MODELS DD4CBW35 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 768 (H) X 494 (V) Horizontal Resolution >540 TV lines Lens F1.4 (f=3.4~119 mm optical, 35X optical zoom, 12X digital zoom) Zoom Speed (optical range) 3.2/4.6/6.6 seconds Horizontal Angle of View 55.8° at 4.2 mm wide z[...]

94 C3412M (9/06) DD4CBW35-X Signal Format P AL Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 724 (H) X 582 (V) Horizontal Resolution >540 TV lines Lens F1.4 (f=3.4~119 mm optical, 35X optical zoom, 12X digital zoom) Zoom Speed 3.2/4.6/6.6 seconds Horizontal Angle of View 55.8° at 4.2 mm wide zoom; 1.72° at 147 mm tel[...]

PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted [...]

Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands | United Arab Emirates | United Kingdom | United States W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com[...]