Philips CCC 092AT manual

CCC090A T CCC092A T Color TV built-in VCR Owner’ s Manual[...]

Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits. Return your Warranty Registration card today to ensure you receive all the benefits you’re[...]

Introduction 3 Features • A-B Repeat Play • Automatic Channel Setup • Automatic Head Cleaner • Automatic Tracking Adjustment • Blue Background • Daylight-Savings Time • Dew Sensor • English or Spanish displays • High Quality (HQ) System • One-Touch Recording • Real-Time Counter • Repeat Play • S-VHS Quasi Play Back (SQPB) [...]

4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before Using the TV/VCR . . . . . . . . . . . . .[...]

Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then lifting off the lid. 2 Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. 3 Replace the battery compartment lid. Using the Remote C[...]

6 Hooking Up the TV/VCR 1 Connect an antenna or cable signal to your TV/VCR using one of the following connections. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. Connect a Cable signal or an antenna to the AN[...]

Hooking Up the TV/VCR (cont’d) 7 Rod Antenna (supplied) Hooking Up Your TV/VCR with the Supplied Rod Antenna To install the supplied rod antenna, push the base stem of the antenna into the antenna hole on the back of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its le[...]

• Do not watch TV while driving. • Make sure the cigarette lighter jack is free of ashes and other debris. • Always unplug the car battery cord from the cigarette lighter before you unplug it from the TV/VCR. • You must disconnect the car battery cord from the TV/VCR before you can use standard electrical (AC) power. • If you use the TV/V[...]

Turning On the TV/VCR 9 Before you turn on the TV/VCR, make sure batteries are in the remote control and you have connected the TV/VCR correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button. The TV/VCR will come on and this screen will appear. 2 Press the PLAY/ K button or the STO[...]

10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following these steps. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM. SETUP, then press the F.FWD/ B button. PRIMARY SETUP > SEL[...]

Automatic Channel Setup (cont’d) 11 4 Press the F.FWD/ B button or the REW(ind)/ { button to select SAVED (to add that channel) or DELETED (to delete that channel). Repeat steps 3-4 to add or delete other channels. 5 Press the STATUS/EXIT button. Programming of the channel you added or deleted will appear. 3 Press the CH(annel) o o / p p buttons [...]

12 Setting the Clock • Entries that do not match the TV/VCR’s calendar will cause a question mark (?) to appear on the screen. Enter the correct number. • To make corrections while you are setting the clock, press the CLEAR button until the space for the num- ber you want to correct is flashing. Then enter the correct number. Helpful Hints Th[...]

Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2. SET MANUAL CLOCK TIME 09 : 30 PM MONTH – – / – – / – – – – TO CORRECT PRESS CLEAR TO END PRESS EXIT 6 Press two Number buttons for the month,[...]

14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the PLAY/ ▲ button or the STOP/ ▼ button to select AUTO CLOCK, then press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK. Then, press the MENU button. 1 Press the ME[...]

Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on the screen. Press the STATUS/EXIT button. 8 When the clock is set, go to page 19 and set the TV/VCR clock for your time zone. The channel that supplies the time might be broadcasting from a different time zone. So, select your Time Zone to ensure the TV[...]

16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the PLAY/ ▲ button or the STOP/ ▼ button to select AUTO CLOCK, then press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK. Then, press the MENU button. 1 Press the MENU [...]

Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on the screen. Press the STATUS/EXIT button. 6 Use the Number buttons to select your PBS station. ● If CANNOT FIND CLOCK DATA flashes on the TV/VCR screen and you know another PBS channel, press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELEC[...]

18 Daylight-Savings Time 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DAYLIGHT SVG.TIME. Then, press the F.FWD/ B button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight Savings Time). 5 Press the STATUS/EXIT button. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM. SETUP. T[...]

Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. • If you select AUTO at step 5, the TV/VCR will set the clock according to the time zone data of the PBS station it finds. • You cannot select SET TIME ZONE at step 4 if AUTO CLOCK is OFF. Helpful Hints 5 Press the PLAY/ ▲ button or the STOP/ ▼ button to select yo[...]

20 Language Selection Follow the steps below to change the language of the on-screen displays and menus. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELECT LANGUAGE. Then, press the F.FWD/ B button. 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select ENGLISH or ESPAÑOL (Spanish). 5 Press the STATUS/EXIT button. SELECT[...]

Front Panel 21 Screen Cover The TV/VCR screen is protected by a removable screen cover. If you want to remove the screen cover, slide in the two tabs that hold the cover in place, then pull off the cover. Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off. CHANNEL o / p Buttons Press to scan throu[...]

F.FWD/ B Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on the screen. Details are on page 42. Press to change the setting of a menu item or to go to the next menu. ALT. CH (Alternate Channel) Button Press to return to the TV channel yo[...]

Remote Control Buttons (cont’d) 23 CH(annel) o o / p p Buttons Press to scan through the TV/VCR’s available channels. MEMORY Button Press to memorize a tape position at which you set the real-time counter to 0:00:00. Details are on page 41. Or, press to memorize the start and end positions on a tape when setting up A-B Repeat Play. Details are [...]

24 Rear Panel ANT(enna) Jack Connect your antenna or cable here. Details are on pages six-eight. Antenna Hole Connect the base stem of the supplied rod antenna here. Details are on pages seven-eight. AC 120V Jack Connect the AC power cord here. Details are on page seven. DC 13.2V Jack Connect the car battery cord here. Details are on page eight.[...]

1 Press the MENU button. Current Tape Function Time Channel Counter and Counter Memory Tape Speed 12:00 AM STOP CH10 SLP M 1:23:45 A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STAT[...]

TO ADJUST PRESS { / B 26 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select the desired control (BRIGHTNESS, for example). 3 Press the REW(ind)/ { button or the F.FWD/ B button to adjust th[...]

Adjusting the Picture Controls (cont’d) 27 Decrease Increase BRIGHTNESS decreased brightness increased brightness PICTURE decreased contrast increased contrast COLOR paler more brilliant TINT more purple more green SHARPNESS softer clearer Press the REW(ind)/ { button to decrease a picture control. Press the F.FWD/ B button to increase a picture [...]

28 Reminder The channel number will remain on the screen during TV viewing when you set REMINDER to ON. Set REMINDER to ON or OFF by following these steps. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REMINDER. 3 Press the REW(ind)/ { button or the F.FWD/ B button to select ON or OFF. Each press of the REW[...]

Playing 29 • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the PLAY/ ▲ button. • Playback features and options are on pages 38-42. • When you play an S-VHS format tape, you can not get the high reso- lution that would be available on an S-VHS VCR. Noise lines (black and white streaks) may appear[...]

Cassette type / Playback Time Tape Speed T160 T120 T60 SP (Standard Play) 2 hrs. 2 hrs. 1 hr. 40 mins. LP (Long Play) 5 hrs. 4 hrs. 2 hrs. (playback only) 20 mins. SLP (Super Long Play) 8 hrs. 6 hrs. 3 hrs. 30 Recording • You cannot record one channel while watching another. • Recording options are on pages 31-37. • You cannot record if DEFEA[...]

One-Touch Recording 31 A One-Touch Recording (OTR) is an immediate timed recording from 30 minutes to eight hours long. Before you begin, make sure: ● Channels are set. Details are on page 10. ● A tape is in the TV/VCR. The record tab must be intact. 1 Use the CH(annel) o o / p p buttons or the Number buttons to select the channel you want to r[...]

32 Rerecording (Tape Duplication) • Unauthorized recording of copyright- ed television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • Different brands of equipment might operate differently. • Make sure all connections are secure. Otherwise, you might not record both pict[...]

Timer Recording 33 Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears, fol- lowed by the SET CLOCK menu. Details are on page 12-19. ● Channel[...]

ONE TIME PROGRAM PROGRAM 1 CHANNEL – – – TO CORRECT PRESS CLEAR TO END PRESS EXIT 34 Timer Recording (cont’d) 5 Use the Number buttons to enter the channel of the TV program you want to record. ● If you are recording from line input, press 0, 0. A/V IN will appear on the screen. ● If you are recording using a Cable Box, enter the Cable [...]

Timer Recording (cont’d) 35 Turn off the TV/VCR for the recording. Insert a tape in the TV/VCR. Leave the Cable Box/DBS on (if applicable). 8 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 30. You cannot use the SPEED button at this time. 9 Press two Number[...]

36 Timer Recording (cont’d) 6 Repeat steps 1-4 to make sure you cleared the correct recording. Checking or Clearing Timer Recordings 1 With the TV/VCR on, press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR PROGRAM, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select[...]

Defeat Recording 37 Follow these steps to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DEFEAT RECORDING, then press the F.FWD/ B button so that ON appears beside DEFEAT RECORDING. 4 Press the STAT[...]

38 A-B Repeat Play • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 2-3 above. Then, press the PLAY/ o but- ton or the STOP/ p button to select ONE TIME PLAY. Press the F.FWD/ B button so that ON appears beside ONE TIME PLAY. Then, press the STATUS/EXIT but- ton. • The end position (B) must be later[...]

6 Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. . A-B REPEAT A 0:12:34 7 Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A). The[...]

40 Repeat Play Follow these steps to program the TV/VCR to play a tape over and over. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REPEAT PLAY, then press the F.FWD/ B button so that ON appears beside REPEAT PLAY. 4 Press the [...]

Real-Time Counter Memory 41 Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 2 Press the STATUS/EXIT button. The real-time counter will appear on the screen. 3 While the counter rem[...]

42 Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/ B button or the REW(ind)/ { button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button. Super High Speed Searching (LP/SLP) 1 During tape playback, press the F.FWD/ B button [...]

2 Press the PLAY/ o o button or the STOP/ p p button to select VCR SETUP, then press the F.FWD/ B B button. Blue Background 43 If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to O[...]

1 Press the SLEEP/WAKE UP button. • To cancel the sleep timer, press the SLEEP/WAKE UP button. Press the PLAY/ o button or the STOP/ p but- ton to select SLEEP, then press the REW(ind) / s s button or the F.FWD/ B B button to select OFF. Press the STATUS/EXIT button. • To see how much time remains before the TV/VCR shuts itself off, press the S[...]

Wake Up Timer 45 The Wake Up Timer turns on the TV/VCR automatically at a speci- fied time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. To set the Wake Up Timer, follow the steps below. Before you begin: ● Set the clock. If the clock is not set, CL[...]

Usually, the volume bar appears when you press the VOL(ume) o o / p p buttons. If you do not need it, set the VOLUME BAR to OFF. 46 Volume Bar 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VOLUME BAR, then press the F.FWD/ B button. Each press of the F.FWD/ B button will turn the VOLUME BAR ON or OFF. 4 Press the STATUS/EXIT button[...]

Automatic Operation Features 47 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab [...]

48 Helpful Hints Location For safe operation and satisfactory performance of your TV/VCR, remember the following: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation. Do not block the ventilation openings at the top and bottom of the TV/VCR[...]

The remote control is not available, or the remote control will not access the menu. • Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 21. TV/VCR has no power. • Connect the AC power cord securely to the AC 120[...]

AUDIO In Jack: jack on the front of the TV/VCR which is used to record or receive audio from another source. Automatic Channel Setup: process in which the TV/VCR memorizes all available channels. Then, when you push the CH(annel) o / p buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels. • Antenna [...]

Specifications 51 General CRT: 9-inch in line gun Television system: NTSC-M Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec. Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C) Relative Humidity: 10% to 75% Power requirement: AC 120V/DC 13.2V, 60Hz Power consumption: 55W (AC)[...]

RENEWED 90 DAY LIMITED WARRANTY[...]

a-b repeat play . . . . . . . . .38-39 accessories . . . . . . . . . . . . . . .56 ant(enna) jack . . . . . . . . .6-8, 24 audio in jack . . . . . . . . . . .21, 32 automatic playback . . . . . . . . . . . . . . .47 rewind . . . . . . . . . . . . . . . .47 batteries . . . . . . . . . . . . . . . . . .5 blue background . . . . . . . . . . .43 bright[...]

IB8282E001 Printed In Malaysia 0EMN01780 / T4210UL/T4211UM * * * * * S UPPLIED A CCESSORIES O PTIONAL A CCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR. To order [...]