Planar PT1945P manual

PT1945R / PT1945S / PT1945P T ouch Screen Monitor USER’S GUIDE www .planar .com[...]

The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photoc[...]

T able of Contents Usage Notice Precautions ................................................................................................................... ......... 1 Introduction About PT1945R/PT1945S/PT1945P ..................................................................................... 2 T ouch Screen for PT1945R .. ..................[...]

Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k. Precautions Follow all warnings, precautions and maintenance as recommended in this user ’ s manual to maximize the life [...]

Introduction About PT1945R/PT1945S/PT1945P The PT1945R/PT1945S/PT1945P is a 19" fl at panel screen with an active matrix, thin- fi lm transistor (TFT) edge-lit LED liquid crystal display (LCD). This unit is to be used as commercial and light industrial equipment only . Features include: • Direct Analog signal input • Active matrix TFT LC[...]

3 T ouch Screen for PT1945R • Analog 5-wire resistive touch screen for fi nger and stylus input • Surface: Anti-glare treatment • Interface: Dual RS-232 Serial/USB controller • Transmittance: 82%±5% • HID: Windows® 7/8 • Driver: Windows ® 7/8, VIST A, XP , 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux kernel 2.6.x(32 bit & 64 bit[...]

Package Overview Display Power Cord VGA Signal Cable RS-232 Cable (PT1945R/PT1945S only) USB Cable ( A to B) Audio-in Cable Landing Strip User ’s Guide xxxxxxxxx / xxxxxxxxx xxxxxxxxx USER’S GUIDE www.planartouch.com 4 Cable Cover Screw[...]

Installation Product Overview • Front View • PT1945R/PT1945S Bottom View (W ithout Stand) • PT1945P Bottom V iew (Without Stand) 5 RS-232 VGA AC IN USB POWER SWITCH AUDIO PT1945R/PT1945S PT1945P AC IN USB POWER SWITCH VGA AUDIO[...]

6 Start Y our Installation Please follow these instructions so that you can hookup the cables to associated connector . 1. Lay the display fl at on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in t[...]

Connecting the Display (Figure 8.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (8.1). 3. Connect the D-SUB cable from the display's VGA input connector to th[...]

(Figure 8.1) PT1945R/PT1945S PT1945P 8[...]

Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included. 9[...]

VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back o[...]

Remove the Deskstand 11 Remove 4 screws and then remove hinge.[...]

User Controls Side Panel Controls OSD Key Menu off status Menu on status Menu appear Menu disappear/ return to main item Brightness Main item select up/ Adjust up Mute Main item select down/ Adjust down Enter/Select sub-item function Power On/Off 12 Icon key Name Menu Up Down Enter Power[...]

How to Use the OSD Menus Icon Key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the [...]

14 On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizont[...]

Appendix T roubleshooting If you are experiencing trouble with the display , refer to the following. If the problem persists, please contact your local dealer or our service center . Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation" section[...]

16 W arning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of W arning Signal. Please check the cable connections or contact your local dealer or Planar for more information. No Signal This message means that the display has been[...]

Product Dimensions PT1945R/PT1945S 17 431.8 mm 390.9 mm 358.0 mm 249.6 mm 219.0 mm 212.0 mm 67.0 mm ► Side View ► T op View ► Front View[...]

PT1945P 18 ► Side View ► T op View ► Front View[...]

Compatibility Modes Mode Resolution H-Frequency (KHz) V -Frequency (Hz) IBM VGA 720 x 400 31.47 70 IBM VGA 640 x 480 31.47 60 VESA VGA 640 x 480 37.86 72 VESA VGA 640 x 480 37.50 75 VESA SVGA 800 x 600 35.16 56 VESA SVGA 800 x 600 37.88 60 VESA SVGA 800 x 600 48.08 72 VESA SVGA 800 x 600 46.88 75 VESA XGA 1024 x 768 48.36 60 VESA XGA 1024 x 768 56.[...]

T ouch Screen Driver Installation The PT1945R/PT1945S is available with both RS232 and USB connections. The touch driver is located at www .planar .com/support for these operating systems: W indows ® 7/8, VIST A, XP , 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux 2.6.x (32 bit & 64 bit), Apple ® Mac OS. The PT1945P is available with USB connec[...]

PT1945P Optional Calibration T ool Install: Calibrating the touch screen in Windows 7/8: 1. T ap the Start button, Control Panel and then Hardware and Sound. 2. Under T ablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Y es to allow the program to make changes. 4[...]

22[...]

PT1945R/PT1945S Install Instructions: If you are using a PC running Windows® 7/8, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the display . 3. Visit www .planar .com/support. 4. Follow the step-by-step instructions as shown on the pop[...]

When changing the T ouch Interface (RS-232 or USB), please follow instructions below . 1. Uninstall the touch driver . 2. Re-start the computer . 3. Remove the original T ouch Interface (RS-232 or USB). 4. Connect the computer to the T ouch Interface (RS-232 or USB) that you would like to use. 5. Install the T ouch driver , then follow the step-by-[...]

PT1945P Driver Install Instructions: If you are using a PC running, Windows® 7/8, VIST A, XP , 2000, follow the instructions below: 1. Power on the PC. 2. Make sure that the USB cable is connected to the computer . 3. Visit www .planar .com/support. 4. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC runni[...]

T echnical Support Cables and Accessories To fi nd cables and accessories for your Planar monitor , touch screen or other Planar products visit our online store at www . PlanarOnline.com . T echnical Support Visit Planar at http://www .planar .com/support for operations manuals, touch screen drivers, warranty information and access to Planar ’s [...]

Planar Systems, Inc. Customer Service 24x7 Online T echnical Support: http://www .planar .com/ support 1 195 NW Compton Drive Beaverton, OR 97006-1992 T el: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day , 7 days a week © 2013 Planar Systems, Inc. 10/13 Planar is a registered trademark of Planar Sy[...]