Planet Technology GSD-802S manual

User's Manual GSD-800S GSD-802S 8-Port Gigabit Web Smart Ethernet Switch GSD-802PS 8-Port Gigabit Web Smart PoE Switch[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Trademarks Copyright © PLANET Technology C orp. 2007. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLAN ET Technology Corp . All other trademarks belong to their respective o wners. Disclaimer PLANET Technology does not warrant that the hardware will[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS TABLE OF CONTENTS 1. INTRODUCTION ............................................................................................................................................................. 1 P ACKAGE C ONTENTS ......................................................................................[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.8.1 IGMP Snooping Configuration ........................................................................................................................... 47 4.8.2 IGMP Snooping Status ...............................................................................................................[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 1. INTRODUCTI ON Package Contents Check the contents of y our package for following parts: ● Web Smart Gigabit Ethe rnet Switch x1 ● User's Manual CD x1 ● Quick installation guide x1 ● Power cord x1 ● Rubber feet x 4 ● Rack mount accessory ki t x 1 (GSD-802PS Only) If any of these [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Product Features  Physic al Po rt GSD-800S z 8-Port 10/100/1000 Base-T RJ-45 Copper po rts . GSD-802S z 8 -Port 10/100/1000 Base-T RJ-45 Coppe r with 2 Shared SFP / mini-GBIC slots GSD-802PS z 8 -Port 10/100/1000 Base-T RJ-45 Coppe r with 2 Shared SFP / mini-GBIC slots  Gener ic Feat ures z C[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS z LED easy PoE sta tus Monitoring z Pow er feeding on/off and priority con figuration  Manage ment z Remote Web management interfa ce z Firmware upgrade through w eb interfa ce z Cable Diagnostics technology z Support SNMPv1 with R FC-1213/1573 -Inte rface group, Etherne t MIB z SNMP Trap PRODUC[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS RFC-1573-Interface MIB RFC-2819 RMON MIB (Group 1) Standar ds Conforma nce EMI Safety FCC Class A, CE Netw ork St anda rds IEEE 802.3 IEEE 802.3u IEEE 802.3ab IEEE 802.3z IEEE 802.1q IEEE 802.1w IEEE 802.1X IEEE 802.3ad IEEE 802.3x IEEE 802.3af Ethernet Fast Ethernet Gigabit Ethernet Gigabit Ethern[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 2. INSTALLATION This section describes the functi onalities of Gigabit Etherne t Switch’s components and guides how to install it on the desktop or shelf. Basic knowledge of ne tworking is assumed. Please read this chapter completely be fore continuing . 2.1 Product Description The PLANET Gigabit[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 2.1.2 Switch Front Panel Figure 2-1 & 2 -2 & 2-3 shows a front panel of GSD-800S / GSD-802S and GSD-802PS. 1357 2468 1357 2468 1000 10/100 LNK ACT Figure 2-1 PLANET GSD-800S Front Panel Figure 2-2 PLANET GSD-802S Front Panel Figure 2-3 PLANET GSD-802PS Front Panel 2.1.3 LED Indicators ■ L[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS ■ LED of GSD-802PS LED Color Function PWR Green Lights to indi cate th at the Sw itch is powered on. PoE In Use Orange Lights to indica te the port is p roviding 48VDC in -line power. 1000 LNK/ACT Green Lights to indica te that the Switch is successfully connecting to the network at 10 00Mbps. Bl[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Pow er Notice: 1. The device i s a power-req uired device, it mean s, it will not w ork till it is pow ered. If your ne tworks should active all the time, please consider using UPS (Uninterrupted Power Suppl y) for your device. It w ill prevent you from network da ta loss or network downtime. 2. In[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 2.2.2 Rack Mounting To install the sw itch in a 19-inch standard rack, please follows the instructions de scribed below. # Notice: Optional rack-ea r for 10-inch cabine t rack mounting (RKE-10A) and 19-inch cabinet ra ck mounting (RKE-10B) is available upon request. Step1 : Place the Gigabit Ethern[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 2-9 Mounting the Gigabit Etherne t Switch in a Rack Step6 : Procee ds with t he ste ps 4 an d steps 5 of sess ion 2. 2.1 Desktop Installation to connect the netw ork cabling and supply power to the Gigabit Ethern et Switch. 2.2.3 Installing the SFP tran sceiver The sections de scribe how to [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Connect the fiber cable 1. Attach the duplex L C connector on the network cable into the SFP transceiver. 2. Connect the other end o f the cable to a device – switches w ith SFP installed, fiber NIC on a w orkstation or a Media Converter.. 3. Check the LNK/ACT LED of the SFP slot on the front o f[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 3. SWITCH MANAGEMENT This chapter describes how to manage the Gigabit Ethernet Switch. Topics include: - Overview - Management methods - Assigning an IP address to the Gigabit Ethernet Switch - Logging on to the Gigabit Etherne t Switch 3.1 Overvi ew This chapter gives an ove rview of switch manage[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The Gigabit Etherne t Switch must have an Intern et Prot ocol (IP) address accessible for the remote host. 3.2.2 Login the Switch Before you start configure the Gigabi t Ethernet Switch, please note the Gigabit Etherne t Switch is configured through an Ethernet connection, ma ke sure t he manager P[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4. CONFIGURATION The Gigabit Etherne t Switch provide Web interface fo r Switch smart function co nfiguration and make the Sw itch operate more effectively - They can be configured through the Web Brow ser. A network administrator can manage and monitor the Gigabit Etherne t Switch fro m the local [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS ◆ IGMP Snooping - Enables or disables IGMP Snooping on the de vice to filter the multicast stream. ◆ Quality of Service – Mapping the packet level to classify the packets prio rity. ◆ 802.1X Manageme nt – Specify ports with netw ork access control. ◆ MAC A ddress – Dynamic Address Tab[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.2 System 4.2.1 System Info The System Info page provides in forma tion fo r the current device information. Sy stem Info page helps a switch administrator to identify the firmware / ha rdware version and IP subnet address / DHCP server IP address. The screen in Figure 4-2 appears. Figure 4-2 Syst[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS be released. 4.2.2 Misc Configur ation The Misc Configuration includes the System name, Locat ion name , Login Timeout, IP Add ress, Subnet Mask and Gateway. Through the Web Switch Utility, you can easi ly recognize the device by using the System Name and the Location Name. The Login Timeout is to [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Inactivity Timeout Specifies a ti me period fo r the user login. The w eb interface w ill be auto logout if there’re no action s from the login u ser. The defaul t value is 300 seconds; 0 means no ina ctivity time limi t. SNMP Enable Enable or Disable the SNMP function of the device. While se t t[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.3 Port Configuration This function allow s displaying each port’s status. The Link Status in the screen displays the current connecti on speed and duplex mode; else this function will show do wn w hen the port is disconnected. Pre ss the “Refre sh” button to renew the screen. The screen in [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS • Flow Control Allow Enable or Disable flow control for selected port. • Enable – 802.3x flow con trol is enabled on Full-Duplex mode or Backpressu re is enabled on Half-Duplex mode. • Disable – No flow control or ba ckpressure fun ction on no matter Full-Duplex or Half-Duplex mode. • P[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.4 Port Mirroring This function provide to monitoring netw ork traffic that forwards a copy o f each incoming or ou tgoing packet from one port of a netw ork Switch to another port w here the pa cket can be st udied. It enables the manager to keep clo se track of switch performance and alter it i [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.5 VLANs A Virtual LAN (VLAN ) is a logical network grouping that limits the broadcast do main. It allows you to isola te network tra ffic so only mem bers of the VL AN receiv e traffic from the same VLAN m embers. B asicall y, creatin g a VLAN from a s witch is logically equivalent of reconnecti [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.5.1 VLAN Membership This function group individual po rts into a small “Virtual” net work of their own to be independent of the other ports. The screen in Figure 4-6 appears. Figure 4-6 VLAN Membership screen The page includes the follow ing items: • VLAN ID Speci fy the VLAN Identifier for[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-7 Add a VL AN screen Figure 4-8 VLAN Member Setup screen 4.5.1.2 Modify the VL AN Group Member Once you want to modify the existence VLAN Group member or dele te a existence VLAN Group. Refer to the follow ing steps. 1. To modify the members of an existen ce VLAN Group, check the VLAN Grou[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-9 VLAN Group – member modify and dele te VLAN Group screen # Notice: Once the VLAN Group be deleted , the Por ts with the PVID set to th is VLAN Group have to re-configure the PVID. Or the PVID will be set to “N one”[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.5.2 Per Port Configuration The VLAN per Po rt Configuration page con tains fields for m anaging po rts that are pa rt of a VLAN . The port default VLAN ID (PVID) is con figured on the VL AN Port Configu ration page . All untagged packets arriving to the device are tagged by the ports PVID. The sc[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Disab led - all frames are forw arded in accordance with the 802.1Q VLAN bridge specification. The factory default is di sabled. • Acceptable Frame Types Specifies the types of frames that may be received on this po rt. The options are 'All' and 'Tagged only' . • All - untag[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.5.3 VLAN setting example: 4.5.3 . 1 Two se parate 802. 1Q VL AN The diagram show s how the switch handle Tagged and Un tagged traffic flow for t wo VLANs. VLAN Group 2 and VLAN Group 3 are separated VLAN. Each VLAN isola te network traf fic so only members of the VL AN receive tr affic from the s[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS  Untagged packet enter ing VLAN 3 1. While [PC-4] tran smit an untagged packet en ters Port-4 , the switch w ill tag it with a VL AN Tag=3 . [PC-5] and [PC-6] will received the pa cket through Port-5 and Port-6 . 2. While the packe t leaves Port-5 , it will be stripped away it tag becoming an un[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-13 Assign VL AN members for VLAN 2 and VLAN 3 Remember to remove the Port 1 – Port 6 from VLAN 1 me mbership, si nce the Port 1 – Po rt 6 had been assigned to VLAN 2 and VLAN 3. Figure 4-14 Remove sp ecify ports from VLAN 1 member # Notice: It’s import to remove the VLAN members from[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 3. Assign PVID for each port: Port-1,Port-2 and Port-3 : PVID= 2 Port-4,Port-5 and Port-6 : PVID= 3 Port-7~Port-8: PVID= 1 4. Enable VL AN Tag for sp ecif ic p o rt s Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3) The Per Port VLAN configuration in Figure 4-15 appears. Figure 4-15 Port 1-Por t 6 VL[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.5.3.2 Two VLANs with overlap area Follow the example of 4.5.3.1. There ’re two exist separa te VL ANs – VLAN 2 and VL AN 3, and the PCs of ea ch VLANs are not able to access each other of di fferent VLANs. But they all need to acce ss with the same server. The screen in Figure 4-16 appear. Th[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 3. Def ine a VLAN 1 as a “Public Area” that ove rlapping with b oth VLAN 2 member s and VLAN 3 members . Figure 4-18 VLAN 1 – The public area member assign 4. Set up Port-7 with “ PV ID=1 ” a t VLAN per Po rt Configuration page . The screen in Figure 4-19 app ears. Figure 4-19 Setup Port-[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS That is, although the VLAN 2 me mbers: Port-1 to Port-3 and VLAN 3 members: Po rt-4 to Port-6 also belong to VLAN 1. But with different PVID sett ings, packe ts form VLAN 2 or VLAN 3 is not able to access to the other VLAN. 4.5.3. 3 VLAN Tru n king b etw een two 8 02.1Q aw are sw itch The most ca s[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-22 Add VLAN Trunk por t to each VL AN 3. Repeat Step 1 and 2, se tup the VLAN Trunk po rt at the partne r switch. 4. To add more VLANs to join the VLAN trunk, r epeat Step 2 to assign the Trunk port to the VLANs.[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.6 Rapid Spanning Tree Spanning Tree Protocol (STP) provides tree topography for any arrange ment of bridges. STP also provide s one path between end stations on a network, eliminating loops. Rapid Spanning Tree Protocol (RSTP) - While Classic Spanning Tree guarantees preventing L2 forwarding loop[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.6.1 RSTP System Configuration The “RSTP System Con figuration” table allow s configuring the spanning tree parameters. Figure 4-24 RSTP System Configura tion The page includes the follow ing fields: • System Priority Specifies the bridge priority value. When switches or b ridges are running[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS stations, avoiding and eliminating loops. # Notice: • Max Age - . The value lies between 6 and 40, with the value being le ss than or equal to "(2 * Bridge Forward Delay ) - 1" and greate r than or equa l to " 2 * ( Bridge Hello Time +1) ". T he default value is 20. • Hello [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS - Ethernet – 2000000. - Fast Ethernet - 200000. - Gigabit Ethernet - 20000. 4.6.3 RSTP Status The RST P Status page di splay t he cur rent ST P br idge , roor bridge and per port stp sta tus. To access RSTP Status screen and perform the follow ing procedure: 1. Click St atus -> RSTP St atus 2.[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS • Hello Time Minimum time between tran smissions of Configuration BPDU s. • Max Age Path Cost to the Designated Root for the spanning tree. • Forward Delay Derived value of the Root Port Bridge Forward Delay parameter. • Topology Specifies the Tololo gy change status o f the curren t operat[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS • Disabled -- The port link is currently down. • Blocking -- The port is currently blo cked and cann ot be used to fo rward traffic or learn MAC addresses. Blocking is displayed w hen Classic STP is enabled. • Listening -- The port i s currently in the listening mode. The port cannot forward [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.7 Li nk Aggre g at ion Port Aggregation optimizes port u sage by linking a group of ports together to form a single Link Aggregated Groups (LAGs). Port Aggregation multiplie s the bandw idth between th e devices, increases port flexibili ty, and pro vides link redundancy. Each LAG is composed of [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The page includes the follow ing fields: • Port Indicate po rt 1 to port 8. • Normal While a po rt is checked as “Normal” , the port is not joining to any Stati c Trunk Group. • Group Specify the Jo ined Trunk Group. There’re maximum 4 trunk g roups per system. With diffe rent switch mo[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The page includes the follow ing fields: • Port Indicate po rt 1 to port 8. • Prot ocol Enab le T o Enable o r disable the LCAP protocol on a selected port. Once the LACP protocol be enabled , the sy stem will sta rt transmit the LACP control pa ckets and exchange with ano ther LACP aware switc[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.7.3 LACP Status The LACP Sta tus page display the current LACP aggregation Groups and LAC P Port status. To open LA CP St atu s screen perfo rm the folling: 1. Click St atus -> LACP St atus. 2. The “L ACP Aggregation Overview” and “LACP Port Sta tus” screen is display ed as in Figure 4[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The Color and ID l eg end Down Port link down. 0 Blocke d Port Block ed by RSTP. Number i s Partne r port number if other switch has LACP enabled. 0 Learning Port Learning by RSTP. Forwarding Port link up and forwarding fra mes. 0 Forwarding Port link up and forwarding by RSTP. Number is Partner po[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.8 IGMP Snooping The Interne t Group Management Protocol (IGMP) lets host and routers share info rmation about multicast groups memberships. IGMP snooping i s a switch fea ture that monito rs the exchange of IGMP message s and copies them to the CPU for featu re processing. The overall purpose of [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Enabled periodically check the multicast group for me mbers that are no longer active. In the case where there is more than one multic ast route r on a sub network, one router is elected as the ‘queried’. This router then keeps track of the mem bership of the multicast groups that have active m[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The page includes the follow ing fields: • VLAN ID Identifies a VLAN an d contains in formatio n about the Multicast group configuration. • Querier Display the current status of IGMP Querier on the device. Act ive – The IGMP Que ry function h ad been enabled on the de vice and played as a mai[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.8.3 Multicast Grou p Table The Multicast Group page display s the ports attached to the Mult i cast service group in the Ports tables. The Port a tables also reflect the manner in which th e port joined th e Multicast g roup. Ports can be ad ded either to existing groups or to new Multicast servi[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.9 Quality of Service Quality of Service (QoS) is an advanced tra ffic prioritization fe ature that allow s you to establish con trol over network traffi c. QoS enables you to assign various g rades of network servi ce to di fferent type s of tra ffic, such as multi-media, video , protocol-speci f[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-37 QoS Conf igurat ion scr een 4.9.1 802.1p QoS Mode QoS setting s allow customization o f packet p riority in order to facilitate delivery of da ta tra ffic tha t might be af fected by latency pro blems. The IEEE 802.1p Priority specification uses 8 priori ty lev els to cla ssify data pac[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-39 Prioritize Traffic screen The page includes the follow ing fields: • Prioritize Traffi c The dra w menu all ows cus tomizat ion of 802.1p to Tra ffic classi fiers. To tal 5 selections for the P rioritize Traffic. • Custom – Manual mapping the 802.1p priority to the 4-level queues.[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.9.2 DSCP QoS Mode DiffServ Code Point (DSCP) － is the traffic prioritization bits within an IP header tha t are encoded by certain app lications and/or devi ces to indicate the level of service required by the packe t across a network. The DS CP Co nfigu r ation page provides fields for d efini[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.10 802.1X Management The PLANET Gigabit Ethe rnet Switch suppo rts IEEE 802.1X Port-base network access control and RADIUS server authentication to enhance the host lin k more security . An 802 .1 X Infrastructu re is composed of three major components: Authentica tor, Authentica tion server, and[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 8. The cl ient and RADIUS se rver derive encryption key s. 9. The RADI US server sends Web-Smart S witch a RA DIUS ACCEPT message. 10. W eb-Smart Swi tch sends the clie nt an EAP Success message along w ith the broadcast key and key length . This section i s to control the access o f the switch, in[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS The RA DIUS Ser ver co nfigur ation ta ble in cludes t he foll owing fi elds: • Mode To Enable/Disable the port access control administra tive mode. This selector lists the two options for admin istrative mode: enable and disable . The defaul t value is disabled . • RADIUS Server IP The IP addr[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.10.2 Port Access Control This table is to configure the per port ne twork access control setting . By drawing and select the menu bar to de fine the port control type. The screen in Figure 4-44 and Figure 4-45 appears. Figure 4-44 Per Por t network a ccess control configure table Figure 4-45 802.[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS required to press the Submit butt on for the actio n to occur. • Force Re initialize This button begins the re-initializa tion sequence on the selected port. This button is only selectable if the control mode is 'auto' . If the button is not selectable, it w ill be grayed out. Once this[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.11 MAC Addresses 4.11.1 Dynamic A ddress Table Use this page to set the Ad dress Ageing Timeout fo r the MAC Add ress database, and to display in formation abou t entries in the MAC Address database . These entries are used by the transparen t bridging function to determine how to forward a recei[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS will be fo rward to the speci fy port. • MAC-Address Specifies the MAC address fo r which the table is queried . 4.11.2 Static MAC Address The Static MAC Add ress page contains a list of static MAC addresses. Sta tic Address can be added and remo ved from the page. In addition, several MAC Addres[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.12 Tools 4.12.1 Reboot The Reboot page enables the device to be rebooted from a re mote lo cation. Once the Reboot button be pre ssed, user have to re-login the WEB in terface about 20 seconds later, the screen in Figure 4-49 appears. Figure 4-49 Reboot screen 4.12.2 Factory Reset The Factory Res[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.12.3 Firmware Upgrade The F i rmw are Upg rad e page contains fields for downloading system image files from the Local File browser to the device. To open Firmw are Upgr ad e screen perform the folling: 1. Click Tools -> Firmware Upgrade . 2. The Firmware Upgrade screen is display ed as in Fig[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.12.4 Configuration Upload This func tion allows backup and reload the current co nfiguration o f Switch to the local management sta tion. The screen in Figure 4-53 appears.  Confi guratio n Uploa d: Upload the existed configuration file to the Switch. The configuration file had been saved at t[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 2. Select on t he config uration fi le then cl ick “ Upload ”, the bottom of the b rowser shows the upload status. 3. After down, the ma in screen appears “ Transfer Completed ”.  Confi guratio n Downloa d 1. Press the “ Dow nload ” button to save the cu rrent configu ration in manag[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.12.5 Ping Use this scre en to tell the switch to send a Ping request to a sp ecified IP add ress. You can use this to che ck whether the switch can communicate with a pa rticular IP station . Once you click the Apply bu tton, the switch w ill send n pings and the results will be displayed below t[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS # Notice: Be sure the target IP Address is within the same n etwork subnet o f the swi tch, or you had setup the correct gateway IP address. 4.12.6 Cable Diagnostic s The Cable Diagnostics pa ge contains fields for performing te sts on copper cables. These functions have the ability to identify the[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS • Pair The twist pair o f the UTP cable. The pair groups as follow: A (Pin 1,2) B (Pin 3,6) C (Pin 4,5) D (Pin 7,8) • Length[m] When properly terminated, Cable Di agnostics reports the approxima te cable length in m eters o f each of the four cable pair A, B, C, and D. • Statu s Th e cable te[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.12.7 Web Smart Function This function could provide you to define de vice indicate connect to each port on Web Smart Switch, the screen in Figu re 4-60 appears. Figure 4-60 Web Smart Function Web Page screen The available op tions are shown as below : 1 PC 2 PC+VoIP 3 Switch 4 Router 5 AP 6 Serve[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 3. After setup comple ted, press “A pply ” to save current configuration, the screen in Figure 4-62 appears. Figure 4-61 Web Smart Function Web Page screen Figure 4-62 Web Smart Function Web Page screen[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS This function also provides Apply for all ports option from Select a port function, the setup procedure shown a s below: 1. Choose a device and check “A pply for all port s” from o ptions of Select a por t function, the scree n in Figu re 4-63appears. 2. Check any port then all port will be sel[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-64 Web Smart Function Web Page screen Figure 4-65 Web Smart Function Web Page screen[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.13 Status Click on the “ Stat us ” to present th e Switch sta tus on this screen, it display s the following sta tus:  Port Statistics  LA CP S ta tus  RSTP Statu s  IGMP Snooping Status  Multicast Group Table 4.13.1 Port Statistics The Port Statistic Overview page displays the[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS • Transmit Octet s Nu mber of octets of data (including tho s e in bad packe ts) transmitted on the port. This object can be used as a reasonable estimate o f Ethernet utiliza tion. • Broad- and Multicast Number of packets transmitted on the po rt. Include the b roadcast and multicast packets. [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Figure 4-68 Login screen[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 4.14 PoE Configuration ( GSD-802PS Only) The GSD-802PS is an 8 ports PoE Layer 2 Web Smart switch, it supports up to 8 ports PoE Power source (PSE) to supply PoE power fo r the connected Pow er Device (PD).  Power Ma nagemen t: In a power over Etherne t system, opera ting power is applied fr om [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS Delivering Po w er [W] List each conne cted device power usage. Current [mA] List each conne cted device cu rrent usage. Priority Allow to assign the POE power provision priority on each POE port, the available values a re o Low o Medium o High Also, from the Sw itch panel at the top side , the ora[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 5. SWITCH OPERATION 5.1 Address Table The Switch is implemented with an address table. This addr ess table compo sed of many entries. Ea ch entry is used to store the address informa tion of some node in network, including MAC address, port n o, etc. This information co mes from the learning proces[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 5.5 Auto-Negotiation The STP ports on the Switch have built-in “Auto-negotiation”. This technology automatically sets the best possible bandwidth when a con nection is established w ith another network devi ce (usually a t Power On o r Reset). This is done by detect the modes and speeds a t the[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS A host will never send a report when it w ants to leave a group (for ve rsion 1). A host will send a “leave” report when it wants to leave a group (for version 2). Multicast routers send IGMP queries (to the all-hosts gr oup address: 224.0.0.1) pe riodically to see whether any group members exi[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS 6. TROUBLESHOOTING This chapter contains info rmation to help you solve problems. If the Switch is no t functioning prope rly, make sure the Ethernet Switch was set u p according to instructions in this manual. The Link LED i s not lit Solution: Check the cable connection and re move duplex mode of[...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS APPENDIX A A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- Implicit implemen tation of the crossover function within a twisted -pair cable, or [...]

User’s Manual of GSD-800S / GSD-802S / GSD-802PS A.3 RJ-45 cable pin assignment 21 3 6 1 2 3 6 2 1 3 6 There are 8 wires on a standard U TP/STP cable and each wire is colo r-coded. The follow ing shows the pin allocation and color of straight ca ble and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure [...]