Runco X-200i manual

XtremeProjection™ Series X-200i Active 3D Home Theater Projector X-200i X-200i/CineWide X-200i/CineWide with AutoScope I NSTALLATION /O PERATION M ANUAL[...]

[...]

Runco X-200i Series Installation /Operation Manual iii PRE L IMINAR Y RuncoCare™ S tandard Two Year Limited Warranty Congratulations o n your purchase of a Runco® product ! With proper installation, se tup and care, you should enjoy many yea rs of unpara lleled video p erformance. This Limited Warranty is provided free of charge by Runco In tern[...]

iv Runco X-200i Series Installation/Operation Manual PRE L IMINAR Y • In the event of a product defec t, please follo w the claim proc edure provided below: A. Register your p roduct if you have not yet done so. Visit ht tp://www.r unco.com/s upport/produ ct-registratio n/ to register the p roduct. B. Contact your o riginal authorized d ealer or [...]

Runco X-200i Series I nsta llation/Operation Manual v PRE L IMINAR Y 4. Damage, det erioration, or malfunction re sulting from: A. Accident, abus e, misuse, neg lect, improper ve ntilation, fire, w ater, disaster, lightning, or oth er acts of natur e, smoke exposure (cigarette or otherwise), unaut horized product mo dification (includin g use of an[...]

vi Runco X-200i Series Inst allation/Operation Manu al PRE L IMINAR Y Runco offers e xtended and e xpanded servic e plans. For in formation on ad ditional produc t protection, p lease ask your authorized Run co dealer, e mail serviceor ders@runco. com or call (toll fr ee) (800) 23RUNCO (800-237-8626 ). RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLI[...]

Runco X-200i Series I nstalla tion/Operation Manual vii PRE L IMINAR Y Thank you fo r your purchase of this qualit y Runco video product! Fo r the best pe rformance, please read this m anual carefully as it is your guid e through the menus and ope ration. 1. Read th ese instruction s. 2. Keep th ese instruction s. 3. Heed all warnings. 4. Follow al[...]

viii Runco X-200i Series In stallation/Operation Manu al PRE L IMINAR Y Please read an d make sure you understand the following safety information before using the produc t for viewing 3D content. Provide this infor mation to the e nd users of th is product and ensure that the y understan d it. IMPORTANT HEALTH AN D SAFETY INFORMATION FOR 3D VIEWIN[...]

Runco X-200i Series I nsta llation/Operation Manual ix PRE L IMINAR Y Manufacturer’s Name: Runco International, LL C Manufacture r’s Address: 119 5 NW Compton Dr ive, Beaverton, OR 97006-19 92 hereby declare s that the Prod ucts’ Model Numbers: X-200i, X-200i/ CineWide and X-2 00i/CineWide with AutoScope conform with th e provisions of: Counc[...]

x Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y NOTE: This equipment ha s been tested and found to comply with the limits for a Class B digita l device, pur suant to Part 15 of the FCC Rules. T hese limits ar e designed to p rovide reasonab le protection ag ainst harmful inter ference in a resid ential installation. This equipme[...]

Runco X-200i Series Insta llation/Operation Manual xi 1 Table of Contents PRE L IMINAR Y RuncoCare™ S tandard Two Year Limited Warran ty ........ ................... ................. ....... iii Important S afety Instructions ...... ............. ................ ................. ................ ................ ... vii Compliance Information [...]

Table of Contents xii Runco X-200i Series Installation/Operation Manual PRE L IMINAR Y Installing the Optional CineWid e Lens Mount .............. ............. ............ ............. .......... 23 Installing the Lens Motor (X-2 00i/CineWide with AutoSc ope) ......... ............. .......... 24 Installing the Fixed CineWide Base Plate (P risma[...]

Table of Contents Runco X-200i Series Insta llation/Operation Manual xiii PRE L IMINAR Y 4. Operation .......... ................ ................ ................ ................ ................ ............. .......... 49 Selecting Video Mem ory ...... ................ ................ ................ ............. ................ .......... [...]

Table of Contents xiv Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Notes:[...]

Runco X-200i Series I nsta llation/Operation Manual xv 1 List of Figures PRE L IMINAR Y 2-1. X-200i Key F unctional Co mponents .... ................ ................ ................ ................. ........ 5 2-2. X-200i Rea r View (without Door) ....... ................ ................ ................ ................ ............ 7 3-1. IR [...]

List of Figures xvi Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 4-11. X-200i Se rvice Menu .. ................. ................ ................ ................ ................ ............. 7 1 6-1. NEC Proto col Messag e Format ..... ................ ................ ............. ................ ................ 92 7-1.[...]

Introd uction Runco X-200i Series I nsta llation/Operation Manual 1 PRE L IMINAR Y 1.1 About This Manual This Owner’s M anual descri bes how to install, set up and o perate the R unco XtremeProjec tion™ Series X- 200i Active 3 D Home Thea ter Projector. Throughout th is manual, the Run co XtremeProjection™ Se ries X-200i Active 3D Home Theate[...]

Introduc tion 2 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Graphic Convention s: These sym bols appear in n umerous plac es throughout the manual, to emp hasize points th at you must k eep in mind to a void problems wit h your equipment o r injury: 1.2 Using This Manual Use the following ta ble to locate the spec if ic inform[...]

Introd uction Runco X-200i Series I nsta llation/Operation Manual 3 PRE L IMINAR Y 1.3 Description, Features and Benefits Runco’s Xtreme Projection™ Ser ies X-200i Active 3 D Home Thea ter Projector — t he flagship member of the Xtrem eProjection se ries — is a sing le-chip DLP project or that, uncalibrated, measures 1,430 AN SI lumens and [...]

Introduc tion 4 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Key Features and Benefits The X-200i offers thes e key features and be nefits: • Native Resolution: 1920 x 108 0 (16:9 Native Aspect Ratio) • DLP system using high-performance Digital Micromirror Device (DMD) • Customized color wheel p roduces wide dynamic rang [...]

Controls and Functi ons Runco X-200i Series I nsta llation/Operation Manual 5 PRE L IMINAR Y 2.1 X -200i at a Glance Figure 2-1 shows the key X-200i function al components. Figure 2-1. X-200i Key Func tional Components 2. Controls and Functions Exhau s t V ent V ertical Len s S hift Control Hori z ontal Len s S hift Control Inta k e V ent Exhau s t[...]

Controls and Functions 6 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y • PROJECTION LEN S Available in three versions: stan dard throw range (1 .85:1 to 2.40:1), sho rt throw range (1.56:1 to 1.86:1) and lo ng th row range (2.40:1 to 4.00:1). • IR S EN S OR S Two sensors on the front of the projec tor receive inf rared signa[...]

Controls and Functi ons Runco X-200i Series I nsta llation/Operation Manual 7 PRE L IMINAR Y 2.2 X -200i Rear Panel Figure 2-2 shows the X-200 i rear panel. Figure 2- 2. X-200i Rear View (without Door) 1. LAMP COMP AR TMENT COVER Remove this cover to acce ss the lamp compartme nt when replaci ng the lamp. 2. POWER INPUT (100 to 240 V AC) Connect th[...]

Controls and Functions 8 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 6. R S -232 A female, 9-pin D-su b connector for interfacing w ith a PC or ho me theater automation/control system. 7. RGB Provides a stand ard, 15-pin VGA-st yle connection to eit her an RGB or component high-defin ition source, or to a personal compute r. T[...]

Controls and Functi ons Runco X-200i Series I nsta llation/Operation Manual 9 PRE L IMINAR Y 2.3 Controls and Indicators An eight-butt on keypad on the project or rear panel provides an alternative to t he remote control unit fo r controllin g the project or. Two LEDs next to th e keypad provide visu al indicati ons of the curre nt operatio nal sta[...]

Controls and Functions 10 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 2.4 X -200i Remote Control 1. ON Use this butt on to turn the projector on. 2. OFF Use this butt on to turn the projector off. 3. Aspect Ratio S election B uttons Press one of thes e buttons to sele ct an aspect ratio: 16 : 9: For viewing 16 :9 DVDs or HDTV [...]

Controls and Functi ons Runco X-200i Series I nsta llation/Operation Manual 11 PRE L IMINAR Y 9. Brightness Press to adjust black level. 10. Memory Prese t Buttons: I S F NIGHT Press to recall settin gs for the current in put from the “ISF Night” memory pre set. I S F DA Y Press to recall sett ings for the curre nt input from the “ISF Day” [...]

Controls and Functions 12 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 2.5 X -200i Active 3D Emitter The Active 3D Em itter, shown b elow, receives a left/right synch ronization signa l from the projector a nd transmits it to the Act ive 3D Glasses worn by the viewers. T his signal precisely controls when left and right fields [...]

Installation Runco X-200i Series I nsta llation/Operation Manual 13 PRE L IMINAR Y 3.1 Remote Control To install batteries in the remote co ntrol: 1. Slide the bat tery compartm ent cover in t he direction o f the arrow to remove it. 2. Install two AA batt eries with the correct polarity. 3. Replace the co ver. Notes on Batteries • Make sure that[...]

Installation 14 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y • The projecto r’s front IR receive rs have a range of appr oximately 40 feet (1 2.19 meters). Figure 3-1 show s the reception angle s of the IR receivers. Figure 3-1. IR Reception Angles[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 15 PRE L IMINAR Y 3.2 Quick Setup Table 3-1 gi ves a quick overvie w of the X-200i i nstallation process. The section s following this one prov ide detail ed instruc tions. Installation must be performed by a quali fied custom video installation specialist. Table 3-1. Installation Ove[...]

Installation 16 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 3.3 Installation Considerations Proper insta llation of your p rojector will e nsure the qu ality of your display. Wh ether you are installing a pr ojector tempo rarily or perman ently, you shou ld take the following into account to ensure your proj ector perform s op[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 17 PRE L IMINAR Y Ambient Light In general, minimize or eliminat e light so urces directed at the screen . Contrast rat io in your images will be noticeably reduc ed if light directly st rikes the screen, such as when a sh aft of light from a window o r floodlight falls on the image. [...]

Installation 18 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Table 3-3 lists the available X-2 00i Series lens options and the ir associated th row ratios. Table 3-3. X-200i Lens Options and Throw Ratios (Note) Projector Model Throw Ratio with Primary Lens Only Throw Range in inches, with 108 x 60.75-inch (1.78:1) S creen Throw[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 19 PRE L IMINAR Y Vertical and Horizontal Position Proper placement of the projector relative to the screen will yield a rectangular , perfectly-centered image that completely fills the screen. Ideally, the proj ector should be positioned p erpendicular to the screen an d in such a wa[...]

Installation 20 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Figure 3-5. Horizontal Lens S hift (Example Only) 0% Screen Center 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Width (W) Note: This is a gene ral example of lens shift. Lenses vary i n their shift capabilities. No particular lens or projector[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 21 PRE L IMINAR Y Table 3-4 lists th e lens shift limi ts for each availab le X-200i len s, as percentage s and absolute m easurements with a 100 x 5 6 inch (1.78:1 ) screen. Table 3-4. Vertical and Horizontal Lens S hift Limits Primary Lens Option S tandard or S hort-Throw Lens Long-[...]

Installation 22 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Folded Optics In rear-screen applications wh ere space behin d the project or is limited, a mirr or may be used to fold the op tical path, a s shown in Figure 3-6 . The position of the projector and mirror must be ac curately set. If you are considerin g this type of [...]

Installation Runco X-200i Series I nsta llation/Operation Manual 23 PRE L IMINAR Y 3.4 Installing the Optional CineWide Lens Mount If you are insta lling a standard (n on-CineWide) X-200i, skip this s tep and proce ed with Mounting the X-200i ( page 28 ). If you are installing a n X-200i/CineWide wi th a “McKinley” (cylindrical) anamorphic lens[...]

Installation 24 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Installing t he Lens Motor (X-200i/C ineWide with AutoScope) Figure 3-7 shows th e X-200i/CineWide wi th AutoScope moto r assembly. Figure 3-7. X-200i/CineWide with Auto S cope Motor Assembly – Exploded View ➤ 4 Screw , Phillips Pan-Head, M6-1.0 x 12mm (14x) 1 Aut[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 25 PRE L IMINAR Y Install Lens Motor: 1. Position the AutoScope lens motor as shown in Figure 3-7 . 2. Line up the mounting holes on the len s motor housing with those on the under side of the projecto r. 3. Secure the m otor to the pr ojector with the eight (8) su pplied M6 x 1 2mm P[...]

Installation 26 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Installing the Fixed CineWide Base Plate (Prismatic Anamorphic Lens) To install the fixe d CineWide ba se plate on a X-200i/CineWid e with a pr ismatic anamorphic lens : 1. Place the pro jector upside do wn on a bla nket or othe r soft surface . 2. Secure the CineWide[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 27 PRE L IMINAR Y Installing the Fixed CineWide Base P late (Cylindrical Anamo rphic Lens) To install the fixe d CineWide base plate on a X-200i/CineWide w ith a cylindrical anamorphic le ns: 1. Place the proje ctor upside do wn on a bla nket or other soft surface . 2. Place the CineW[...]

Installation 28 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 3.5 Mounting the X -200i There are se veral method s for mounting the projector . Depending on your chosen installation, one method may b e more suit able than anoth er. Floor Mounting (Upright) In typical front and rear scre en installations, the p rojector can be m [...]

Installation Runco X-200i Series I nsta llation/Operation Manual 29 PRE L IMINAR Y 3.6 Connections to the X -200i Proceed as foll ows to connect the X-200i to your video sources, extern al controller (s) – if present – and AC power. When connect ing your equipmen t: • Turn off all equipment bef ore making any connection s. • Use the correc [...]

Installation 30 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Connecting Source Components to the X-200i Connect your vid eo sources to t he X-200i as sh own and des cribed in the sect ions that follow. HDMI/DVI Connections: Se e Figure 3-11 . Figure 3-11. HDMI/DVI S ource Conne ctions ➤ Use the HDMI inpu ts whenever possib le[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 31 PRE L IMINAR Y RGB Connection: Connect your personal computer or oth er RGB source to the RGB input. See Figure 3 -12 . Figure 3-1 2. RGB Conn ection SYNC 3D SY RS-232 RS-232 USB USB COMPONENT 1 COMPONENT 1 12V TRIGGER II I 12V TRIGGER WIRED REMOTE WIRED REMOTE HDMI 2 HDMI 2 RGB RG[...]

Installation 32 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Componen t Video Conn ections: Connect your c omponent video sources to the COMPONENT 1, COMPONENT 2 or RGB inputs as sh own in Figure 3-13 . Figure 3-13. Component Vide o Connections 3D SYNC 3D SYNC RS-232 RS-232 USB USB COMPONENT 1 COMPONENT 1 12V TRIGGER II I 12V T[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 33 PRE L IMINAR Y RS-232 Controller Connection Connect a PC o r home theate r control/au tomation syste m (if present) t o the RS-232 por t on the X-20 0i; see Figure 3-14 . Use a standard, 9- pin serial cable, w ired straight-t hrough. For more in formation abou t using this con nect[...]

Installation 34 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Connecting an External IR Receiver to the Projector If infrared sig nals from the r emote contr ol cannot reach the projecto r due to ex cessive distance or o bstructions su ch as walls or cabinet doo rs, you can con nect an exter nal IR receiver to e xtend the ra nge[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 35 PRE L IMINAR Y Connecting the Active 3D Emitter to the Projector Connect the 3D S YNC IN port on the emitter t o the 3D S YNC conn ector on th e projector, as shown in Figu re 3-17 . Figure 3-1 7. Active 3D E mitter Con nection Connecting to AC Power Projector: The X-200i ships wit[...]

Installation 36 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 3.7 Turning on the Power 1. Turn on your sour ce component s. 2. Set the Aut oScope lens motor pow er switch to the “o n” position. 3. Press the ON button on the r emote contro l (or the POW ER button on the system keypad) to turn on the X-200i. The blue POWER LED[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 37 PRE L IMINAR Y 3.8 Lens Adjustments The X-200i give s you a grea t deal of cont rol over the picture size, po sition and focu s. Focus and Zoom To focus the projected imag e, grasp the lens by the front ring and rot ate it. To make the pict ure smaller (zoom out ), slide the zoom c[...]

Installation 38 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 3.9 Changing the OSD Language The X-200i ca n display the OSD menus in Englis h (default), French, Germ an, Italian, Spanish, Swedish, Simp lified Chinese, Tr aditional Chinese, Ja panese, Korean, Portuguese or Russian. To change th e OSD language: 1. Press MENU on th[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 39 PRE L IMINAR Y 3.10 Adjusting the Picture Orientation If the X-200i is ceiling-mounte d and/or installed behind th e screen, you mu st change the picture orient ation to mat ch the installation method. To d o this, press MENU on the remote con trol. Then, se lect S Y S TEM from th [...]

Installation 40 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Cylindrical Anamorphic Lens Installation and Adjustment The Cylindrical Anamorph ic lens mount kit consists of everyt hing shown in Figure 3-18. Some compon ents shipped wit h your projector may differ slightly from what is show n in these instruction s. If any items [...]

Installation Runco X-200i Series I nsta llation/Operation Manual 41 PRE L IMINAR Y Attach Lens Mounting Assembly to Lens Motor Carriage Pla te: 1. Remove the two Yaw /X Adjust ment Lev ers and Washer s ( 8 ) from the bottom of the Anamorphic Le ns Holder ( 6 ). 2. Place the Anamo rphic Lens Holder on top of the AutoSco pe Carriage Plate or Fixed Ci[...]

Installation 42 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Configure Lens Motor Trigger (CineWide with Auto S cope ): CineWide with AutoScope ma intains const ant image he ight indep endent of th e aspect ratio, while using th e full display resolu tion of the projecto r. It accomplishes this b y moving the anamorph ic lens i[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 43 PRE L IMINAR Y Adjusting the Height (Y): With the white field still on-sc reen, loosen the Height/Y Adjustment T-Scr ews on either sid e of the lens. Then, slowly move the anamorphic lens into plac e so that t here are no shadows on t he top or b ottom of th e screen: When the heig[...]

Installation 44 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Yaw Adjust: Loosen the Y aw/X-Adjustment Levers to allow the len s to pivot freely from side to side. T hen, angle th e lens to even out any left-to -right pincush ion distortio n: Once the proper lens angle has be en set, firm ly tighten the Y aw/X-Adjustment Lever s[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 45 PRE L IMINAR Y Whitney (Prismat ic) Anamorphic Lens Installation and Adjustment The Whitney Anam orphic lens mo unt kit consists of e verything shown in Figure 3-20. Some compone nts shipped w ith your projector may d iffer slightly from what is shown in these instructions. Figure [...]

Installation 46 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Adjusting th e Lens Heig ht and Angl e: 1. Project a w hite field on th e screen. 2. Loosen the f our Height/Pitch Ad justment Screws just enough to allow vertical movement of t he lens assembly. 3. Slowly move the anamorphic lens into place so that there are no shado[...]

Installation Runco X-200i Series I nsta llation/Operation Manual 47 PRE L IMINAR Y Adjusting the Horizontal Position and Yaw: 1. Project a white field on the scree n. 2. Release the Swell Latche s to allow the lens assembly to pivot and mo ve freely from side to side. 3. Slowly move the anam orphic lens into plac e (from right to left or vice vers [...]

Installation 48 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Notes:[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 49 PRE L IMINAR Y 4.1 Selecting Video Memory Press I S F NIGHT , I S F DA Y , CU S T1 or CU S T2 to recall settings from a memory preset. Then , press ENTER to confirm your selectio n. Or, to cancel the operation, p ress to select Cancel and press ENTER . 4.2 Selecting an Aspect Ratio To[...]

Operation 50 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 4.4 Using the On-Screen Menus 1. Press the MENU button on the rem ote control or system ke ypad to display the Master Menu. 2. There are six menus. Pres s or to select a sub-menu , then press ENTER (remote control unit) or S ELECT (system keypad). 3. Press or to select a[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 51 PRE L IMINAR Y Figure 4-1. X- 200i O S D Menu S tructure Main Aspect Ratio 16:9 , Letterbox, 4: 3, VirtualWide, Cinema or Virtual Cinema Memory Recall Memory Save Memory Save ISF Overscan Off , Crop or Zoom 3D Control 3D Mode Enable DLP Link L-R Swap Dark Time Sync Delay 1080p24 O utp[...]

Operation 52 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Main The X-200i M ain Menu, shown in Figure 4-2 , provides acce ss to the most commonly-used pr ojector functions. Figure 4-2. X-2 00i Main Me nu ➤[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 53 PRE L IMINAR Y Aspect Ratio: To change the aspect r atio (size and sh ape) of the pr ojected image, press or to highlight Aspect Ratio . Use the or buttons to select th e appropriate aspect ratio f or your screen size, installed lens c onfiguration a nd the type of program material be[...]

Operation 54 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Letterbox With a 16:9 source image, Letterbox mode crops the top and bottom portion of the image and vertically stretches the remaining portion to fill a 16:9 image area. It scales (zooms in on) a 4:3 image linearly (by the same amount on all sides) to fill a 16:9 displa[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 55 PRE L IMINAR Y Cinema Select Cinema to view 2.35 source material in its native aspect ratio. With a 16:9 screen and no anamorphic lens, the upper and lower portions of the screen are masked, but the geometry of the active image area is unchanged. With a 2.35:1 screen an d an anamorphi[...]

Operation 56 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Memory: Select Memory fr om the Main menu , then press ENTER to re call image qual ity settings previously sa ved, or to s ave changed settings in any of fo ur memory loc ations. • Recall Memory: Select Reca ll Memory from the Memory menu to recall sa ved image quality[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 57 PRE L IMINAR Y Overscan: Some television prog rams are produced based on the assumptio n that older television sets may not display the oute r edge s of the broad cast pictur e area. Overscan effectively hide s these inactive, outer edges o f the image . Choose one o f the following: [...]

Operation 58 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 3D Control: Select 3D Control fro m the Main Menu to set th e following opt ions related to formatting and delivery of HDMI 3D content. • 3D Mode: Select 3 D Mode from th e 3D Control me nu to specify h ow the X-200 i processes the “left eye” and “righ t eye” i[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 59 PRE L IMINAR Y • 1080p24 Output: This control selects ho w 24Hz 3D content will be processed in an active 3D system. This lowe r frame rate can le ad to excessive fl ickering, creating a need for fra me rate conver sion (FRC). Choo se one of the following: • 96Hz emplo ys a 2:2 ca[...]

Operation 60 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Brightness: On your external te st pattern so urce, select a PLUG E pattern. (PLUG E is an acronym for “Pict ure Line-Up Gene ration Equipment .”) Figure 4- 5 shows a typical PLUGE pattern. Figure 4-5. Typical PLUG E Pattern fo r Adjusting Br ightness PLUGE patterns [...]

Operation Runco X-200i Series I nsta llation/Operation Manual 61 PRE L IMINAR Y Contrast: On your exte rnal test patte rn source, se lect a stepped, gray-bar patte rn like the one shown in Figure 4-6 . Figure 4-6. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast from the Main m enu. Use the or butto ns to adjust t he contrast up unti[...]

Operation 62 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y S harpness: “Sharpness” is the amount of high-frequ ency detail in the ima ge. To adjust this, selec t Sharpness from the Main menu and press ENTER . On your external test pattern sour ce, select a p attern like t he one shown in Figure 4-7 . Figure 4-7. Typical Test[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 63 PRE L IMINAR Y Advanced Image Use the controls in the Ad vanced Image menu , shown in Figure 4-8, to perform ad vanced image adjustment s. Figure 4-8. X-200 i Advanced Image Menu Color S pace: Select Color Space fro m the Advanced Image menu to choose the c olor space of the source si[...]

Operation 64 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Gamma: Select Gamma from t he Advanced Im age menu to c hoose a DLP de-ga mma curve. The a vailable setting s are 1.8, 2 .0, 2.2, 2.35 and 2.5. Th e value chos en here corresponds t o the power vari able in this equatio n: Output = Input Power The X-200i app lies this ga[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 65 PRE L IMINAR Y • REC709 chooses the REC709 color gamut . • Select S MPTE-C to choose the SMPT E-C color gamut. • Select EB U to choose the EBU color gamut . • Select Native to us e REC709 for c yan, magenta , and yellow an d uncorrec ted values for red, gr een, and blue . • [...]

Operation 66 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y RGB Adjust: To remove any trace of c olor from the white a reas of the p rojected im age, choose RGB Adjust from the Advanced Image menu and press ENTER . This displays the RGB Adjust sub-menu, sho wn at right. •G a i n : Use the Gain controls to correct color imbalanc[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 67 PRE L IMINAR Y • S ync Level (Component source s only): Select Sync Level to ad just the voltage level of the X-20 0i Sync signal de tection circuitry. Sync Level ad justment is occasionally necessary when a DVD player or HDTV source signal drops “bel ow black” (for e xample, du[...]

Operation 68 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y White Balance: To precise ly adjust the white point associated with the custo m color gamut, choose White Balance from the PCE sub-menu. Th ese controls ope rate identically to the Gain controls in th e RGB Adjust menu (describ ed on pag e 66 ). System Use the contro ls [...]

Operation Runco X-200i Series I nsta llation/Operation Manual 69 PRE L IMINAR Y Blank S creen: Select Blank Screen from the System menu to choose the c olor of the blank screen tha t appears when no source sign al is present. The opti ons are Black , Blue and White . Th e default is Black . Auto Power Of f: Set Auto Power Off to On to have the X-20[...]

Operation 70 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Control Select Control from the Main Men u to set various o ptions related to control of the projector . Trigger 1: Select Trigger 1 from the Control m enu to specify w hen the Trig ger 1 port outputs 12 volt s. There is a th ree-second delay before activat ion to preven[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 71 PRE L IMINAR Y Infrared Remote: Select Infrared Remote fro m the Contr ol menu to spec ify the remote IR code set to which the X-200i re sponds. The default is Normal . Choose Code 2 if other equipment in the theater resp onds to comm ands from t he X-200i remot e control in ways that[...]

Operation 72 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y You can also per form various diag nostic tasks, such as displaying test patterns, from th is menu. S ystem Informatio n: Select System In formation from the Service m enu to view information that uniquely identifies your projector: its Model Name , Se rial Number , inst[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 73 PRE L IMINAR Y 4.5 Using the 3D Glasses The 3D LCD Shutter Glasses func tion with the Runco Active3D Emitter and the projector to provide unsurpassed 3D st ereoscopic viewing. This secti on describes the feat ures, connection, s etup and operat ion of the 3D LCD Shut ter Glasses. Key [...]

Operation 74 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Charging the Batte ry The glasses m ust be fully charged be fore first use and whenever the Batte ry Status LED flashes red onc e every couple of seconds. The gl asses will charge a compl etely dead battery in ap proximately five h ours. You may use the glasses wh ile th[...]

Operation Runco X-200i Series I nsta llation/Operation Manual 75 PRE L IMINAR Y Turning On the Glasses 1. Ensure that the projecto r is powered on and displaying 3D content. 2. Press and hold the Po wer Button for ab out two seconds, the n release the butt on. The LED then blinks in a pattern that in dicates the ba ttery charge state. In gener al, [...]

Operation 76 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Notes:[...]

Maintenance and Troubleshooting Runco X-200i Series I nsta llation/Operation Manual 77 PRE L IMINAR Y 5.1 Lamp Replacement The lamp should be replac ed when it rea ches the end of its life (typ ically between 1,500 and 3,000 ho urs), or sooner if a noticeable d egradation i n brightness occu rs. Contact your Runco dealer to obtain a rep lacement la[...]

Maintenance and Troublesho oting 78 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 5.2 Troubleshooting Tips Table 5-1 provide s some general guidelines for troubleshooting pr oblems you may encounter with the X-200i. If the suggeste d solutions fail to resolve the problem or if you encounter a n issue not described her e, please [...]

Maintenance and Troubleshooting Runco X-200i Series I nsta llation/Operation Manual 79 PRE L IMINAR Y Colors in the image are swapped; for example, reds appear blue or vice versa. •T h e R e d / P r , G r e e n / Y o r Blue/Pb outputs from t he source are connected to the wrong inputs on the X-200i. • Ensure that the source outputs are connecte[...]

Maintenance and Troublesho oting 80 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Notes:[...]

Runco X-200i Series I nsta llation/Operation Manual 81 PRE L IMINAR Y In addition to using the X-200i ke ypad or remote cont rol unit, ther e are three meth ods of controlling the projector externally: • Using a serial (R S-232) link to sen d ASC II commands and receive responses to those commands. • Using discrete infrared (IR) codes to progra[...]

External Control 82 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Key Commands: The syntax for key commands is simple: ky <keyname>[CR] Some key command exam ples: ky menu[CR] Bring up or ca ncel menu di splay. ky cur.up[CR] Up arrow. The response fr om the projector for key commands is ACK: followed by the s ame command i[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 83 PRE L IMINAR Y (none) 0x87 0xC7 Switch to 2.2 ga mma. 0x8B 0xCB Switch the active source to HDMI 1. 0x8C 0xCC Switch the active source to HDMI 2. 0x8D 0xCD Switch the active so urce to Compo nent 1. 0x8E 0xCE Switch the active so urce to Component 2. 0x8F 0xCF Switch the active[...]

External Control 84 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Operations Commands: Operations comma nds allow more flexible and direct control of the projector . The syntax for operation s commands is as follows: op <operation> <command>[CR] (Precede <operation> an d <command> with a space.) The comma[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 85 PRE L IMINAR Y Response: ACK:INPUT = 0 [CR] Input: op phase = 50 [CR] Response: ERR:NA [CR] Input: op phase ? [CR] Response: ERR:NA [CR] The last thr ee comman ds show what happens when a control is u navailable. In th is case, the source was set to “HDMI 1” (value = 0) and[...]

External Control 86 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y resync (execute) color.space = ? 0 = Auto 1 = REC709 2 = REC601 3 = RGB-PC 4 = RGB-Video gamma = ? 0 = 1.8 1 = 2.0 2 = 2.2 3 = 2.35 4 = 2.5 color.temp = ? 0 = 5500K 1 = 6500K 2 = 7500K 3 = 9300K 4 = Native frame.rate = ? 0 = Auto 2 = 48 Hz 3 = 50 Hz 4 = 60 Hz colo[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 87 PRE L IMINAR Y blank.screen = ? 0 = Logo 1 = Black 2 = Blue 3 = White logo.disp = ? 0 = Off 1 = On auto.poweroff = ? 0 = Off 1 = On auto.poweron = ? 0 = Off 1 = On proj.mode = ? 0 = Front Tabletop 1 = Front Ceiling 2 = Rear Tabletop 3 = Rear Ceiling model.name ? <string> [...]

External Control 88 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y trig1 trig2 = ? 0 = Lamp 3 = 4:3 4 = AutoScope 5 = RS232 6 = On 7 = Off adcontrast = ? 0 = Off 1 = On blue.only = 0 = Off 1 = On osd.timer = ? 0 = forever 1 = 10 sec. 2 = 30 sec. 3 = 60 sec. ir.enable = ? 0 = Disable 1 = Code 1 2 = Code 2 menu.pos = ? 0 = Top left[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 89 PRE L IMINAR Y 3D.syncdelay = ? 100 +/- 40 ms 3D.syncinvert = ? 0 = Normal 1 = Inverted power.chime = ? 0 = Off 1 = On errcode ? Refer to RS-232 Error Codes on page 91 . lamp.vol ? <string> returns lamp voltage cinewide = ? 0 = Off 1 = CineWide 2 = AutoScope red.hsg.hue y[...]

External Control 90 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y cal.text1 cal.text2 cal.text3 = Up to 30 characters. The X-200i start-up screen is cus - tomizable with three lines of text of up to 30 characters each. This text appears below the “CALIBRATED FOR:” text in the logo screen. The allowable characters are all num[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 91 PRE L IMINAR Y RS-232 Error Codes If an errcode ? command returns one of the following values, you have encountered a likely system error requiring the attention of a qualified service techni cian. Try resetting the projector by powerin g it off, allowing it to cool and po weri[...]

External Control 92 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y 6.2 Using Discrete IR Codes The X-200i accept s commands in the form of IR si gnals that conform to the NEC protocol . Each X-200i rem ote control but ton has an NEC control co de associated with it. As shown in T able 6-1, ther e are two com plete sets of r emote[...]

External Control Runco X-200i Series I nsta llation/Operation Manual 93 PRE L IMINAR Y 6.3 Using HDMI CEC Messages The X-200i ac cepts and ca n respond t o CEC comm and message s from a disc p layer, satellite receiver or DVR/set-to p box via an HDMI connection. Using CEC, the X-200i can perform the following action s: • Turn itself on a nd selec[...]

External Control 94 Runco X-200i Series Inst allation/Operation Manual PRE L IMINAR Y Vendor Remote Button Down 0x8A [Vendor Specific RC Code] Yes Yes Give Device Vendor ID 0x8C No ne Yes No Menu Request 0x8D [Menu Request Type] Yes No Meun Status 0x8E [Menu State] Yes No Give Device Power Status 0x8F None Yes No Report Power Status 0x90 [Power Sta[...]

Specifications Runco X-200i Series I nsta llation/Operation Manual 95 PRE L IMINAR Y 7.1 X -200i Specifications Table 7-1 lists the X-200i specifications. 7. S pecifications Table 7-1. X-200i S pecifications Projector Type Digit al Light Processing™ (DLP™), Single-Chip, 16:9 SuperOnyx™ DMD™ , 3D Capable Native Resolution Full HD 1920 x 1080[...]

Specifications 96 Runco X-200i Series Inst allation/Operation Manual P RELI M INARY Limited Warranty Projector: (2) Two years parts and labor from the date of shipment from Runco. Ex tended RuncoCare™, Red Carpet™, and PremierC are™ a lso available. Processor Dual Stream Vivix™ technology processing Control Options • Di screte infrared (I[...]

Specifications Runco X-200i Series I nsta llation/Operation Manual 97 PRE L IMINAR Y 7.2 X -200i Dimensions Figure 7-1 shows the X-200i dimensions, in millimeters. Figure 7-1. X-200i Dimensions Ø 2 3 3 583 252 223 FRONT JEWEL 646 624 R432 R432 R1427 R1435 R1016 MESHØ 2.0x3.0P LOUVER MESHØ 2.0x3.0P[...]

Specifications 98 Runco X-200i Series Inst allation/Operation Manual P RELI M INARY 7.3 Supported Timings Table 7-2 lists the signal typ es supporte d by each inp ut on the X-20 0i. Table 7-2. S upported S ignal Timings by Input Format Resolution Refresh Rate (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) S upported? ( √ = Yes, – = No) R[...]

Specifications Runco X-200i Series I nsta llation/Operation Manual 99 PRE L IMINAR Y S upported 2D Modes 640x480 640x480 60.00 31.469 25.175 √ – √ 66.59 35.892 29.862 √ – √ 75.00 37.500 31.500 √ – √ 85.00 43.269 36.000 √ – √ 800x600 800x600 60.00 37.879 40.000 √ – √ 75.00 46.875 49.500 √ – √ 85.00 53.674 56.250 ?[...]

Specifications 100 Runco X-200i Series In stallation/Operation Manual P RELI M INARY Notes:[...]

[...]

Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com 020-1200-00 Rev. A September 20 12[...]