Samsung SHR-2041 manual

Real T ime DVR SHR-2040/2041/2042 User ’ s Manual SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page i[...]

SHR-2040/2041/2042 USER’S MANUAL ii Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● This may cause abnormal heat generation or fire ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you. ● This m[...]

iii W ARNING [Battery] As wrong exchange of the battery in SHR-2040/2041/2042 may cause explosion, you shall use the certified battery for SHR-2040/2041/2042. The battery specification is as follows. -Normal V oltage: 3V -Normal Capacity: 220mAh -Continuous Standard Load: 0.2mA -Operating T emperature: -30 ~ +60 ˚C [System Shutdown] - Power -off w[...]

iv Safety Regulations Before we start Standards Approvals Chapter 1 Overview 1. Introduction 2. Features 3. Part Names and Functions Chapter 2 Installation 1. Installation Environment Setup 2. Checking Product & Accessory 3. HDD Addition Chapter 3 Connecting with Other device 1. Connecting Video, Audio, & Monitor 2. Connecting the Network 3[...]

v Chapter 5 Menu Setup Before Use 1. System 2. Camera 3. Monitoring 4. Recording Mode 5. Event Record Mode 6. Record Schedule 7. Backup 8. Network 9. Network Setup Chapter 6 PTZ Camera Control 1. PTZ camera Control Mode 2. Basic Operation of P AN, TIL T , & ZOOM 3. Preset Setup 4. Camera Menu Setup 5. Preset View 6. Other View Chapter 7 Recordi[...]

vi Chapter 9 Smart Viewer 1. Introduction 2. Feature 3. PC Specification(Recommendation) 4. Smart Viewer Installation 5. Smart Viewer Program Execution 6. Smart Viewer Initial Screen 7. Monitoring Mode 8. Search Mode 9. Setup Mode Appendix 1. Product Specification 2. The specification of HDD and peripheral device 3. Outline Drawings 4. Factory Defa[...]

Chapter 1 Over view 1 SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1[...]

1 Intr oduction 1-1 The Digital Video Recorder(DVR) compresses the 4 channel of camera input data into the MPEG4 video file and the 4 channel of voice input data into the ADPCM audio file in the real time to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously . In addition, it transfers the Video/Audio out through a netw[...]

2 Features 1-2 ■ 4 CH Composite Input Connectors ■ NTSC / P AL V ideo Source Compatible ( NTSC : SHR-2040/SHR-2041/SHR2042, SHR-2040N / SHR-2041N / SHR-2042N PA L: SHR-2040P/SHR-2041P/SHR2042P) ■ Able to record the CIF sized (NTSC-352 x 240/P AL-352 x 288) video at the speed of 120 ips(NTSC)/100ips(P AL)(Image Per Second) ■ 4 CH Loop Throug[...]

No. Name Function SHR-2040/2041/2042 USER’S MANUAL 3 Par t Names and Functions 1-3 Power LED HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Mode Selection Button Search Audio Setup Button Displays power on/off condition. 1 2 3 5 Network LED Displays both network connection and data transmission condition[...]

1-4 No. Name Function RECORD MENU (PRESET) Button ZOOM(TELE) Button PTZ Button SEARCH(VIEW) Button FREEZE(WIDE) Button Direction Button Key Search Function Key Sets up Digital Zoom(x2). ( Performs the TELE function by pressing the PTZ button.) Performs the TELE, WIDE, PRESET , and VIEW function. Performs the FREEZE function in the DISPLA Y Mode. ( [...]

SHR-2040/2041/2042 USER’S MANUAL 1-5 [SHR-2041] [SHR-2042] No. Name Function Channel Button Selects a channel in the Single Mode. Used for number input button in the number input mode. Power LED HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Split Screen Selection Button Display Mode Audio Setup Button D[...]

1-6 Mode Selection Button Search MODE Displays 4 split screen. Displays the selected channel to the Single Mode Displays both LIVE Channel and Playback Channel in the PIP Screen simultaneously . Displays 6 split screen. (1 CH playback screen and 4 CH live screen) Displays 9 split screen. (4 CH playback screen and 4 CH live screen) No. Name Function[...]

SHR-2040/2041/2042 USER’S MANUAL 1-7 Caution Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator . To play DVR on the cabinet or rack, be sure to check the ventilation condition. No. Name Function Composite Video Signal Input Port (BNC Style Connector) Y ou may use THROUGH port to transmit a vide[...]

1-8 No. Name Function Composite Video Signal Input Port (BNC Style Connector) Y ou may use THROUGH port to transmit a video signal to the other video equipment. Audio Signal Input Port (RCA Jack) Audio Signal Output Port (RCA Jack) Composite Video Signal Output Port (BNC Style Connector) VGA Video Signal Output Port S-VIDEO Video Signal Output Port[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2[...]

Chapter 2 Installation 2 SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3[...]

1 Installation Envir onment Setup 2-1 Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator . To play DVR on the cabinet or rack, be sure to check the ventilation condition. Y ou should pay attention to the following before you use the product. 1. Do not use it outdoor . 2. Do not let water or liquid in the [...]

2 Checking Pr oduct & Accessor y 2-2 Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it. ■ Main Body ■ User ’s Manual ■ One Power Cord ■ T wo Brackets - These are not supplied in SHR-2040. - Brackets are used to attach[...]

SHR-2040/2041/2042 USER’S MANUAL 3 HDD Addition 2-3 Y ou can add up HDD to the product.(2040-1 HDD/2041-3 HDDs/2042-2 HDDs) However , since the product contains has many parts which may incur electric shock, accident, or product breakdown and improper installation or setup may disturb HDD recognition or normal product operation, you shall consult[...]

2-4 [SHR-2041] [SHR-2042] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-4[...]

SHR-2040/2041/2042 USER’S MANUAL 2-5 2. Detach the cover from the product. (Pull out the cover slightly and lift from the back side to detach.) [SHR-2040] [SHR-2041/2042] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-5[...]

2-6 3. A bracket(BRACKET - HDD) is mounted to each side of product to fix the HDD. Please loosen the screw of the bracket to which you want to fix HDD. BRACKET -HDD SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-6[...]

SHR-2040/2041/2042 USER’S MANUAL 2-7 4. Pull BRACKET -HDD to the product center to detach the fixed part at the bottom and detach BRACKET -HDD from the product. 5. T ighten 4 special screws(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to BRACKET -HDD. (A force to tighten the screw shall be strong enough to resist vibration.) SHR-2040/2[...]

2-8 7. Check if BRACKET -HDD has been fixed to the product and connect both the power supply cable and the signal transmission cable (IDE CABLE) to the HDD. Signal T ransmission Cable (IDE Cable) Power Supply Cable 6. Reattach HDD to the original position of BRACKET -HDD. (Assembly shall be done in the reverse procedure of disassembly as follows. A[...]

SHR-2040/2041/2042 USER’S MANUAL 2-9 8. Check the connector , wiring, and cable fixing condition inside the product and close the cover . 9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side) ✻ Y ou can apply 2 HDDs to each BRACKET -HDD as shown in the figure. Caution Caution For HDD addition, please select the s[...]

2-10 W ARNING ! Regarding the sub fan, you need additional brackets and sub fans as follows. The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan. @ Fix the fan as follows SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-10[...]

SHR-2040/2041/2042 USER’S MANUAL 2-11 # Please install the fan which is seen at the right from the front view of SHR-set as follows. SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-11[...]

2-12 $ The cable should be out from the left hole. SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-12[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-13[...]

Chapter 3 Connecting with other device 3 SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3[...]

1 Connecting the V ideo, Audio, and Monitor 3-1 SHR-2040/2041/2042 USER’S MANUAL [SHR-2040] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-1[...]

3-2 [SHR-2041/2042] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-2[...]

SHR-2040/2041/2042 USER’S MANUAL 3-3 2 Connecting the Network ● Connecting to Internet through Ethernet(10/100BaseT) ● Connecting to Internet through ADSL [SHR-2040] [SHR-2040] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-3[...]

3-4 ● Connecting to Internet through Ethernet(10/100BaseT) ● Connecting to Internet through ADSL [SHR-2041/2042] [SHR-2041/2042] SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-4[...]

1. There are two USB connecting ports on the front and back of SHR-2040/2041/2042. 2. USB Hard Disk, USB CD/DVD, and USB Memory are connected through the front and back ports of SHR-2040/2041/2042. 3. Only one USB device can be connected with each USB connecting port. 4. If the USB HDD is connected to the system, it should be detected and set throu[...]

3-6 4 Connecting the Alarm Input/Output The Alarm IN/OUT port in the back of SHR-2040/2041/2042 is composed of the following elements. ● ALARM IN/OUT Connection Name Function - ALARM IN1 1 - ALARM IN2 - ALARM IN3 - ALARM IN4 2 - ALARM RESET IN 3 - ALARM OUT1 - ALARM OUT2 ALARM Input Port ALARM Output Port On receiving an ALARM RESET signal, the s[...]

SHR-2040/2041/2042 USER’S MANUAL 3-7 ● ALARM IN/OUT Connection SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-7[...]

3-8 5 Connecting the RS-485 Device ● Connect the RS-485 Device through the back port of SHR- SHR-2040/2041/2042. ● Y ou can install and control the PTZ camera supporting the RS-485 communication. ● Y ou can adopt either Half Duplex or Full Duplex method for the connection. ● Baud Rate supports 600/1200/2400/4800/9600/19200/38400. Half Duple[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4[...]

Chapter 4 Live 4 SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5[...]

1 System Operation 4-1 SHR-2040/2041/2042 USER’S MANUAL ● T urn the power on and the following LOGO pops up on the screen. ● After the LOGO appears, all of LED in the front flickers 6 times to initialize the system for operation. ● Upon completion of normal initialization, the Live screen appears accompanying a beep sound. ● It requires 3[...]

2 Live screen Mode 4-2 Definition of Live Screen Icon The Live screen icons display the current setup and function status of each screen. PTZ N CAM_01 CAM_01 V .Loss : Recording Icon Each icon represents Normal / Event (Alarm + Motion) / Schedule Recording. : Recording Video Size Icon Each icon represents the recording size of Large / Normal / CIF [...]

SHR-2040/2041/2042 USER’S MANUAL 4-3 Definition of Live Screen Mode The system receives 3 live images and displays them in the following 3 modes. ● 4 Split Mode: Four channels are split in the screen separately . Y ou are able to choose a channel as you want to in each split mode. ● PIP(Picture In Picture) Mode: Displays a one-fourth sized sc[...]

4-4 Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH4 Button]. The following figure shows Live Mode after converted. ● The default setup is 4 Split Screen Mode. ● Y ou are able to choose other modes than Full Screen Mode by the [MODE] button in sequence. Whenever you press the [MODE] button, the system will ch[...]

3 Live Channel Selection and Audio On/Off Setup In other split modes than Full Screen Mode and Auto Sequence Mode, you can choose a channel to be displayed in each split area on your own. In addition, the channel being set to Audio On can be set to Audio On/Off in all Live Modes. Audio On/Off Setup in the Full Screen In the Full Screen Mode, the se[...]

4-6 4 Freeze and Zoom Freeze Function Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode. Y ou can set Freeze On/Off with [FREEZE] Button and [FREEZE LED] is turned on or off depending on the Freeze On/Off setup condition. Zoom Function Zoom function enlarges the selected area to double size, and it is [...]

5 Event Monitoring Event monitoring displays the channel synchronized with a event on the screen when a special event (Sensor/Motion/Video Loss) occurs. Event monitoring On/Of f and event duration setup is available in [Menu] ➝ [Monitoring] mode. If you set the event monitoring interval to 5 seconds and an event occurs at CH2 in the beginning as [...]

4-8 6 Spot-out monitoring Spot-out Monitoring has nothing to do with Live Screen Output, it monitors the full screen of a certain channel. If you select the Monitoring in the MENU, the one channel among CH1 ~ CH4 is output with a Spot-out or channels are output one by one at an interval as Auto Sequence Mode in the Live Mode. Live screen icon does [...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-9[...]

Chapter 5 Menu Setup 5 SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5[...]

Before Use 5-1 ● Selection The yellow cursor shows the current window . Use the  ,  , ¦ ,  key in the front to move the cursor on your desirous menu. If you press the “Enter” key with the cursor clicking on your desirable menu, the system will enter the new mode. Press the “Enter” key to finish the selection. On seeing Drop Down[...]

1 System 5-2 ● System Menu has the following items in detail. ● Press the “Enter” key and the ¦ ,  key to move to Y/M/D. Use the  ,  key to change the date. Press the “Enter” key to come out of the mode. ● T ime Press the “Enter” key and the ¦ ,  key to move to H/M/S. Use the ¦ ,  key to change the time. Press th[...]

SHR-2040/2041/2042 USER’S MANUAL 5-3 ● Date Format The system supports 3 formats, YYYY -MM-DD / DD-MM-YYYY / MM-DD-YYYY . ● T ime Format The system supports 2 formats, 24 Hour / 12 Hour(AM/PM). ● Language After selecting a language, OSD is expressed in the selected language. The available language is added in the list. ● DST(Daylight Savi[...]

5-4 Password ● The Default Password is 4321. ● New Password This is used to change the system password inside SHR-2040/2041/2042. Y ou are allowed to create a password up to 4 digits. Press the “Enter” key and a channel button from 1 ~ 4 at the left. Press the “Enter” key after change to move to “New Password Confirm”. ● New Passw[...]

SHR-2040/2041/2042 USER’S MANUAL 5-5 Load Factory Default ● It used to initialize all the menu setup values. The recorded data will not be deleted. Press “OK” in the confirmation window to start initializing. System Log ● System Log is used to check the important record by an administrator . ● It displays such contents of a system relat[...]

5-6 ● System Log List Event Log ● It used to check the record regarding Event like Alarm / Motion / Video Loss. ● It displays the contents of a log regarding event and its execution date / time. ● First : Returns to the first Log page. ● Prev : Back to the previous Log page. ● Next : Forwards to the next Log page. ● Last : Moves to th[...]

SHR-2040/2041/2042 USER’S MANUAL 5-7 System Information and Setup ● Software V ersion : Displays the current version. Setup is not available. ● Broadcast Format : Displays the current Format(NTSC/P AL) . Setup is not available. ● Mac Address : 6 Byte hardware address. Setup is not available. ● Device Erase This erases the data in A T A / [...]

5-8 HDD Setup ● HDD Information Displays the number , capacity , and status of A T A and USB device. Setup is not available. Status : Internal HDD, External HDD, Backup HDD ● External HDD Setup 1. Backup/External type Y ou are able to determine the usage of USB. Not Defined ➝ Appears when the usage of connected HDD is not defined. Y ou can se[...]

SHR-2040/2041/2042 USER’S MANUAL 5-9 HDD Mode Setup ● HDD End Mode Stop : Stops recording when HDD is full during the recording. Overwrite : Deletes the original data and save a new data when HDD is full during the recording. ● HDD End Beep On : Beeps when the HDD is full in the recording mode. Off : Although the HDD is full in the recording [...]

5-10 Remote control Device ● MENU for the use of Samsung system keyboard Remote Control Device ID Baudrate Device Samsung System Keybord Parity Date Stop Duplex 03 4800 None 8 1 Half Duplex ● Device A Remote Control Device, being connected to the RS485 port. ● ID This is a private ID of SHR-2040/2041/2042. This private ID is essential for SSC[...]

SHR-2040/2041/2042 USER’S MANUAL 5-11 System Shutdown ● T erminates the work in action safely and turns the power off. Press “OK” in the confirmation window and plug out when you see “Safe to Power Off”. Remote Control Device Caution Caution [System Shutdown] Power-off without terminating the system in the System Shutdown menu may incur[...]

5-12 2 Camera ● The detailed Camera Menu items are as follows. ● V ideo On : Camera images from a selected channel appear . Off : Camera images from a selected channel disappear . Covert1 : Displays the information except for the Video information of selected channel. Covert2 : Does not display the any information. Audio/Cam name/Auto sequence [...]

● T itle Y ou can name the camera of selected channel. If you press the [Enter] key , the Virtual keyboard will come out.  V irtual Keyboard If you move the cursor , you can type text by text. Up to 15 texts can be typed. Keyboard cannot be composed of all spaces. Pressing Caps Lock changes the keyboard that can be selected. (2 Modes) SHR-2[...]

5-14 PTZ Device ● ID It is an ID for PTZ Camera and available to set from 0 to 255. ● Protocol It is supported by the PTZ device. The following protocols are now being supported. Samsung/ Vicon/ Panasonic/ AD/ Philips/ Erna/ PelcoD/ PelcoP/Vcltp/ Diamond/ Kalatel ● Baurate Baurate is supported by the PTZ device. 600/ 1200/ 2400/ 4800/ 9600/ 1[...]

Screen Setup SHR-2040/2041/2042 USER’S MANUAL 5-15 ● It is a window to set Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set Brightness/Contrast/Color . Once selected, the channel appears in the right PIP area. Use the  or  button to adjust the value from 0 to 100[...]

5-16 3 Monitoring ● Event Monitoring It is possible to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous. ① Off : Event Monitoring does not operate to turn to the screen where an event occurs. ➁ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : Sets the duration time of screen in the Auto Sequence mode. ➂ Continuous : The Event Monitoring screen remains al[...]

● Monitor Y ou are not allowed to connect VGA OUT and Composite/S-Video OUT simultaneous- ly . Consequently , the user is obliged to choose either Composite Output or S-Video Output. ① Composite : Makes the output come out through the “Composite / S-Video OUT” port. ➁ VGA : Makes the output come out through the “VGA Out” port. When ch[...]

5-18 4 Recording Mode Record Mode ● Details for Record Mode Menu are as follows. If you press the front “REC” button, the mode value to be recorded will be set. ☛ For the setup of Event Recording Mode value, refer to 5-20. Event Recording Mode Setup Menu. ● Mode On : The current channel is recorded if the REC button is pressed. Off : The [...]

SHR-2040/2041/2042 USER’S MANUAL 5-19 ● V ideo size It sets the video to be recorded. Half D1 : (NTSC) 720x240(N) . Normal (P AL) 720x288(N) . Normal CIF : (NTSC) 352x240(C) . CIF (P AL) 352x288(C) . CIF ● Auto Deletion Press the [Off] button at the bottom of left to select either OFF or On. Select “On” to move to the Date selection butto[...]

5-20 5 Event Record Mode ● The detailed items of Event Record Menu are as follows. Event Record Mode setup ● Event Record Mode setup Sets a mode to be recorded when an event occurs. ● V. Size (Video Size ) Sets the size of a screen to be recorded. Half D1 : (NTSC) 720x240(N) ➝ Normal (P AL) 720x288(N) ➝ Normal CIF : (NTSC) 352x240(C) ➝ [...]

SHR-2040/2041/2042 USER’S MANUAL 5-21 ● Quality Quality will be determined. Select the one among V ery High/High/Normal/Low . ● Rate Sets the Rate the number of screen recorded every second. It you set to 15ips, the system records too many screens per second and play continues intermittently since recording is more detailed. This is appropria[...]

5-22 Alarm Detection Setup ● Off : Sensor does not operate. ① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) ➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued. ( B Contact) ● Cam Sets a camera that will synchronize with the cur[...]

SHR-2040/2041/2042 USER’S MANUAL 5-23 Motion Detection Setup ● Motion Detection Mode Off : Motion Detection does not operate On : Motion Detection operates. ● Area Selects the Motion Detection area. It is composed of 45x40(NTSC)/45x48(P AL) sized Block. It is impossible to set 4 block rows(Up/Down/Left/Right) to allow them to be displayed in [...]

5-24 ● Sensitivity Sets the sensitivity of motion detection. Sensitivity grade consists of Low ➝ Medium ➝ Ve r y High in the ascending order . ● Alarm-Out Sets the Alarm-Out when Motion occurs. 5 Alarm Outs are supported. Select an alarm-out that you want to synchronize with the current motion channel. Multi-selection is possible. ● Beep-[...]

SHR-2040/2041/2042 USER’S MANUAL 5-25 6 Record Schedule This setup selects a time to record automatically . Selection by the day or by the time is available. The default value is set to “Event Record”. ● Press “CH >” copies the value of Channel 1 to all the channels. ● The horizontal axis numbered from 0 to 23 represents the time v[...]

5-26 ● Schedule / Event Record On occurrence of Event, Continuous Recording is replaced with Event Recording Mode. ● Holiday If you press “Holiday”, a calendar pops up and you are able to designate holidays. Move to a date and press “Enter” to complete designation. Press “Enter” once more to cancel designation. “H” at the bottom[...]

SHR-2040/2041/2042 USER’S MANUAL 5-27 7 Backup ● If there is a device, the free space and the backup device is displayed. ● Select a date, time, and camera No. to backup, and press “Start”. ● When you change Start Date/T ime or End Date/T ime, free space keeps updated in the Free Space zone. ● A file name is composed of Folder/File Na[...]

5-28 8 Network ● Connection Mode Designates the kind of the network connected to the main body of SHR-2040/2041/2042. Static IP : When the main body is connected to the network with Static IP . Dynamic IP : When the main body is connected to the network with Dynamic IP supplied by DHCP . ADSL(PPPoE) : When the main body is connected to the ADSL n[...]

SHR-2040/2041/2042 USER’S MANUAL 5-29 Caution Caution In case of ADSL, the audio is not played in the SmartV iewer . Caution Caution Be sure to set IP/Port/SubnetMask/Gateway/DNS to let Smart V iewer connect with the main body of SHR-2040/2041/2042. W rong IP/Port/Gateway/SubnetMask/DNS may prevent Smart V iewer from being connected to the main b[...]

5-30 Note Note If you want to connect IP Router with the main body of SHR-2040/2041/2042, you shall designate a port for SHR-2040/2041/2042 in the IP Router setup menu. The main body of SHR-2040/2041/2042 uses 4 ports for TCP communication. In addition, if you want to use the DHCP function backed by IP Router to allocate Dynamic IP to the main body[...]

SHR-2040/2041/2042 USER’S MANUAL 5-31 Callback Settings ● The Callback function is used to forward a callback message to the IP where SmartViewer is in action in case Alarm, Motion Detection, or Video Loss event occurs. ● On/Off : Of f is default but you may choose On. ● IP Address : IP setting is available only when On is selected from On/[...]

5-32 9 Network Setup Port Setup for SmartViewer Connection ● The Port value for DVR registration of SmartViewer (Setup ➝ Site Setup) shall be as same as that of the set (TCP). ● If you want to use the IP Router , you shall forward the activated Port depending on the current setting value. - If set to TCP , allocate 4 ports to the IP Router wh[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6[...]

Chapter 6 PTZ Camera Contr ol 6 SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7[...]

1 PTZ Camera Contr ol Mode 6-1 ● Select a proper PTZ camera Configuration value in MENU to enter PTZ Control Mode. ● Selected in MENU, the PTZ symbol( ) is displayed on the channel in the screen. ● If you press the Enter( ) button among direction keys in front of Split Screen, a blue bar will appear in the monitor screen. Use direction keys t[...]

6-2 ● Other PTZ Camera Control Modes perform its control in a single screen. Press the channel selection button in the left front to select the PTZ setting channel and press the PTZ button. If you succeed in entering Single Screen PTZ Camera Control Mode, the PTZ symbol on the screen will turn yellow from white while the PTZ button will turn blue[...]

SHR-2040/2041/2042 USER’S MANUAL 2 Basic Operation of P AN, TIL T , & ZOOM 6-3 ● PA N Press the LEFT or RIGHT button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera horizontally . ● TIL T Press the UP or DOWN button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera vertically . PTZ T[...]

3 Preset Setup 6-4 ● Records a certain position of PTZ Camera. ● Memorizes up to 20 PTZ Camera positions at the moment. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to set up Preset. ● After Preset setup, press ENTER. PTZ TELE WIDE VIEW PRESET Note Note For AD Protocol PTZ Camera, this me[...]

SHR-2040/2041/2042 USER’S MANUAL 6-5 ● Move the cursor to right and press ENTER in PTZ Control Mode first. Then, press the “Enter” to run P/T/Z/ operation mode in the PIP screen and press the “Enter” again to cancel P/T/Z/ Motion Mode. ● Press Enter at the Position Name position to see Virtual Keyboard. Enter the type position name an[...]

4 Camera Menu Setup 6-6 ● Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several conditions of PTZ Camera. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Camera Menu. ● Press the “Preset” button in front of SHR-2040/2041/2042 to return to the upper menu f[...]

SHR-2040/2041/2042 USER’S MANUAL 5 Preset V iew 6-7 ● Preset setup allows your movement to a certain saved position of PTZ Camera. ● Press the VIEW button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Preset.(For example, Samsung Protocol) ● Control the cursor until it reaches a preset position number tha[...]

6 Other V iew 6-8 ● Press the “VIEW” button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to supply PTZ Camera. This is a very special function. ● After you select a function, press Enter . Then the function will be checked and start running. ● If you select other function during the operation, the previous funct[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-9[...]

Chapter 7 Recording 7 SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7[...]

1 REC (Normal Recording) 7-1 ● Pressing REC the button starts recording as set in the record mode. Then, REC LED lights on and a recording icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ● During the normal recording, you can stop it by pressing the REC button. If the recording stops, REC LED lights out. SHR-2[...]

2 Schedule Recording 7-2 ● While “Record Schedule” or “Schedule/Event recording” is selected in the Record Schedule menu, Schedule Recording automatically starts. Otherwise, Schedule Recording remains inactivated. During the Schedule Recording, Recording Icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ?[...]

SHR-2040/2041/2042 USER’S MANUAL 3 Event Recording 7-3 ● Alarm Detection Sensor operation mode in Alarm of Event Record menu shall be set to N.O (Normal Open) or N.C (Normal Close). ● Motion Detection Motion detection in the Event Recording menu shall be set to On. ● V ideo Loss Detection V ideo Loss in Event Record menu shall be set to On.[...]

Chapter 8 Search and Play 8 SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-4[...]

Before Use 8-1 ● Pressing the “SEARCH” button shows Search Menu on the screen as seen above. ● Calendar Search searches a video file by the use of a calendar at the desired time. ● Event Search searches a video file recorded by the occurrence of event. ● Date/T ime Search searches a video file by the entering of a day and time. ● “G[...]

1 Calendar Search 8-2 ● Be sure to select both the channel and the date to search. And press the [Start] button to search for the desired time. ● Use a calendar to search the video file of desired time. Four channels in maximum are in the range of search. ● Select the channel up to 4 by the use of ¦ ,  and Enter button. And then the date [...]

SHR-2040/2041/2042 USER’S MANUAL 8-3 ● Searches Normal Recording, Schedule Recording, Alarm Recording, Motion Recording, and V .Loss(V ideo Loss) Recording by the time. ● Y ou shall select a channel to search to see the event information of the channel. ● On the basis of event information for each channel, the system searches a video file f[...]

3 Date/Time Search 8-4 ● Use the Day/T ime information to search a video file at the time as you desire. Up to 4 channels can be searched at once. ● After you select a channel with the  ,  , [Enter] button, the checkbox on the right of selected event number will be checked. ● Use the  button until you reach the Search T ime setup lin[...]

SHR-2040/2041/2042 USER’S MANUAL 8-5 ● Searches the oldest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the  ,  , [Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. An[...]

5 Go to Last Search 8-6 ● Searches the latest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the  ,  ,[Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. And press the [Can[...]

Note Note SHR-2042 supports the internal CD-R/W . 6 Backup SHR-2040/2041/2042 USER’S MANUAL 8-7 ● First, select the backup device. ● Mark the data of device. ● Select the file name to backup, and the detail information of a file is displayed in the below . ● The [Previous] button shows the previous page. ● The [Next] button shows the ne[...]

7 Playback 8-8 Note Note Pressing the PLA Y button( ) does not affect the playback as far as the user stays in the MENU. Be sure to exit from the MENU to start the playback. ● Press the STOP button( ) to stop the playback. If you press the Playback/P AUSE button( ) once more, the recording will resume from the point where the previous recording s[...]

SHR-2040/2041/2042 USER’S MANUAL 8-9 ● Definition Play Screen Mode ① 4 Split Screen : If you select more than a channel, 4 Split Screen will appear . ➁ Single Screen : This appears when you select one channel in Search. If you press the [CH1~CH4] button in the other split screen, the selected channel appears with the single screen. If you p[...]

8-10 ● Play at Faster Speed If you press the LEFT or RIGHT button( / ) during the playback, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or reversely . ● V iewing Still Screen If you press the LEFT or RIGHT button( / ) when the system paused, you will be able to see still screens forwardly or re[...]

SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 1[...]

9 Chapter 9 Smar t V iewer SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9[...]

1 Intr oduction 9-1 SHR-2040/2041/2042 USER’S MANUAL Smart Viewer is a program that a general PC user is able to install SHR-2040/2041/2042 to his PC to monitor the video and audio data in the real time through network without going to the site where SHR-2040/2041/2042 is installed. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-1[...]

2 Feature 9-2 ● Thanks to the transmission of video data compressed by the MPEG-4 Video Compression method, it can play the video images of good quality . ● Thanks to the G.726 V oice Compression method, it supplies the voice data of good quality . Use of armored MIC improves the quality of remote voice. ● Thanks to the transmission of video/[...]

SHR-2040/2041/2042 USER’S MANUAL 3 PC Specification(Recommendation) 9-3 ● OS : Win98SE, WinMe, Win2000, WinXP ● Recommendation : CPU Pentium 3 1GHz or higher RAM 256 MB or higher VGA RAM 32Mb or higher DirectX 8.1 or higher Note Note Depending on Recording Rate, V ideo Size, and user ’ s PC specification set to SHR-SHR-2040/2041/2042, the n[...]

4 Smar t V iewer Installation 9-4 Smart Viewer Installation ● Put a Smart Viewer Program CD in CD-ROM and open the “Smart V iewer” folder in the CD. ● Run the “Setup.exe” file. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-4[...]

SHR-2040/2041/2042 USER’S MANUAL 9-5 ● Click the “Next” button. ● If you agree with Smart Viewer License, click “Y es”. ● Designate a folder to install Smart Viewer in it and click “Next”. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-5[...]

9-6 ● The system proceeds with setup file installation and system setup. ● Installation is complete. Click the “Finish” to terminate the installation. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-6[...]

SHR-2040/2041/2042 USER’S MANUAL 5 Smar t V iewer Pr ogram Execution 9-7 ● Double-click the Smart Viewer icon in the background screen to run the program. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-7[...]

6 Smar t V iewer Initial Screen 9-8 ● Screen Description ! This is the button to enter the Search mode in which you can search and play remote the video file recorded in SHR-2040/2041/2042 and enter the Monitoring mode for real-time video monitoring. @ This button terminates or minimizes the program. # It displays the current date, day , and time[...]

SHR-2040/2041/2042 USER’S MANUAL 7 Monitoring Mode 9-9 ● DVR(SHR-2040/2041/2042) / SITE Connection - Select the name of DVR(SHR-2040/2041/2042) or site for connection and click the connection button.  Connection Failure Cases 1. Password Certification Failure - In case of discord between the Network password set to SHR-2040/2041/2042 and the[...]

9-10 ● Monitoring Mode Connection Screen ● Mode Conversion Button - This button converts the monitoring mode and the search mode. Note Note No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to access SHR-2040/2041/2042 simultaneously .(In the case of multicast, 5 User authorized users are allowable.) Note [...]

SHR-2040/2041/2042 USER’S MANUAL 9-11 ● Ti me Information - As soon as you are connected to SHR-2040/2041/2042, the current date, day , and time of SHR-2040/2041/2042 will be displayed. - Otherwise, the current date, day , and time of your PC will be displayed. ● Connection Information - As soon as you are connected to SHR-2040/2041/2042, the[...]

9-12 Note Note # Clicking the speaker icon turns the audio of channel on or off. : Audio OFF : Audio ON If you turn the audio of a SHR-2040/2041/2042 channel off, “Disable” will be displayed. : Audio Disabled ✴ For the Audio on channel now , use the following audio button to adjust the volume and set the mute. Note Note % the alarm or motion [...]

SHR-2040/2041/2042 USER’S MANUAL 9-13 ● Event Log Display Window - Click the Log button to activate the log display window . - It displays the event(alarm, user connection, and setup change) occurring at SHR-2040/2041/2042 in the real-time. Note Note [Event Message]  Connecting.. : T rying to connect to SHR-2040/2041/2042.  Connected.. : [...]

9-14 Caution Caution When Time Change, Load Factory Default, Network Change, System Shutdown, or Hdd Format event occurs, Smart V iewer terminates the connection automatically . ● Camera connection Indication Window - Displays the connection condition of DVR and CAMERA in the list. Note Note [DVR Icon Color]  Successfully connected to SHR-2040[...]

SHR-2040/2041/2042 USER’S MANUAL 9-15 ● Monitoring screen condition Information / Selection Button - Displays the Split or Monitoring condition of the screen in play . ● Screen Split Selection Button - Small Sized Single / Single / Quad / Nine-Split Mode Sixteen-Split Mode - Y ou can change the Split Mode of the screen under monitoring. ● S[...]

9-16 : When monitoring with Quad Mode : When monitoring with Single Mode : Camera Off Note Note The number in the screen icon indicates the screen position in SmartV iewer . : The orange icon indicates the current channel is connected to a camera. : The gray icon indicates the current channel is connected to a camera but not displayed in the screen[...]

SHR-2040/2041/2042 USER’S MANUAL 9-17 ● NEXT Button - Click the NEXT(Mouse Left Button) to see the channel next to the current channel. - In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 1 (CH) - In Quad Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) - In Nine-Split Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) - In Sixteen-Split Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) ● CALLBACK Button[...]

9-18 ● FA VORITE Button - If you press F A VORITE, the FA VORITE window will be activated. If you click the current F A VORITE, the cameras saved in the current setting value will be displayed in the screen. Y ou may delete the selected F A VORITE or all F A VORITE setting values. Y ou may set up a new F A VORITE number and name. Change F A VORIT[...]

Note Note The adjusted Audio volume, brightness, and contrast values will be saved in your PC and remain unchanged even if you terminate Smart V iewer and restart it. * OS of Windows 98 or ME do not support this Brightness/Contrast function. SHR-2040/2041/2042 USER’S MANUAL 9-19 ● Audio V olume Control Button - Y ou can control the audio volume[...]

● PTZ Camera Control Buttons - Select a channel connected to PTZ Camera to control PTZ related functions. - P AN Left / Right - TIL T Up / Down - Diagonal Control - The channel under PTZ control will be displayed in the center of the button. 9-20 Note Note The P AN / TILT / ZOOM function is supported to all the cameras. But, POWER ZOOM is support[...]

If you click the current PRESET number and name, the camera will move to its position. Y ou can delete the selected or all the PRESET setup values. Y ou can set a new PRESET number and name. SHR-2040/2041/2042 USER’S MANUAL 9-21 Note Note ! The PRESET function is supported to all the cameras. Y ou are allowed to set no more than 20 PRESET items. [...]

9-22 Note Note The Camera Menu Setup function is supported by Samsung and Panasonic camera only . ● Self Menu Setup of PTZ device ! This is a Menu screen supplied by the camera itself, seen from Viewer . @ Use the  /  /  /  button for the movement between menus. # This is a button for the role of Enter . ! Y ou can set the function me[...]

SHR-2040/2041/2042 USER’S MANUAL 8 Search Mode 9-23 ● The initial screen of search mode - The search mode is divided into the remote mode to search and play the SHR-2040/2041/2042 video and the local mode to play *.dvr file saved in the directory designated by your PC. ! To change to the search mode for the remote control of video recorded in S[...]

9-24 ● DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE - Same as “DVR(SHR-2040/2041/2042)/SITE Connection” of the monitoring mode. ● Remote Mode - This mode transfers the video data recorded in SHR-2040/2041/2042 by network for the playback. - Up to 4 channels are allowed for simultaneous search and playback. - The video informa[...]

SHR-2040/2041/2042 USER’S MANUAL 9-25 ● Calendar Window - If the video data in on-line SHR-2040/2041/2042 was recorded, the date turns red. - If you click the date in red, the saved video information is displayed. - The currently selected date will be marked with a thick red box. - ¦ : Moves to the previous month. -  : Moves to the ne[...]

9-26 @ Backup Button - If not playback(Stop), the video save button performs the backup function. - If the save button is pressed, the window for backup pops up. - Set a Start/End tome for backup and select a file format to save. - The backup starts when the “Start” button is clicked. The backup file is saved according to the setting route; Set[...]

SHR-2040/2041/2042 USER’S MANUAL 9-27 $ Print - This function outputs the screen zone of the playback video which is now being displayed. % Setup Mode Button - This button pops up the setup mode window . ● Play Buttons ! Play : Play @ Reverse Play : Reverse Play # Stop : Stop $ Fast Forward : Faster Play % Fast Backward : Faster Reverse Play ^ [...]

9-28 Note Note During the play(Play/RevPlay/FF/FB), disconnection or change to the both monitor- ing mode and local mode is not permitted. Click the Stop button first before the change. Note Note Double click the area closed by the time bar to change to the zoom in mode. One column of time line represents an hour . T ime Line turns Green(Normal), R[...]

SHR-2040/2041/2042 USER’S MANUAL 9-29 ● Next Button - Changes the channel as the Next button does in the monitoring mode. ● Reload Button - Updates the record time information in the calendar window and time line. ● Local Mode - Plays *.dvr file saved in the directory of your PC by the Record function. - Y ou can search and play only one ch[...]

9 Setup Mode 9-30 ● Initial Screen ! Button to select items for DVR Setup, Viewer Setup, Site Setup, and S/W V ersion setup. @ It shows what the selected Setup item can set up in detail. # button to terminate the setup window . $ Button to save the information revised in the setup window , remark the information prior to such a revision, or termi[...]

● Setup Item Selection Button - It is used for the selection of each setup item. - It is composed of 4 items- DVR Setup, Viewer Setup, Site Setup, and S/W V ersion. - DVR Setup: Allows you to change the remote menu setup items of SHR-2040/2041/2042. - Viewer Setup : Allows you to set the various kinds of item concerning the operation of Smart Vie[...]

9-32 DVR Setup - Click the [DVR Setup] button for DVR Setup. - Y ou can change remotely the setup items of SHR-2040/2041/2042 Menu, being connected with Smart Viewer . - DVR Setup is composed of 5 items; System, Camera/Audio, Monitoring, Recording, and Network. Note Note - - Y Y ou are authorized with access to DVR Setup in an Admin authority only [...]

SHR-2040/2041/2042 USER’S MANUAL 9-33 ● Detailed DVR Setup Items ! System - Information Information shows the information on on-line SHR-2040/2041/2042. Note For the detailed items of DVR Setup, refer to Chapter 5. - Password Sets the password for the control of SHR-2040/2041/2042 Menu or SHR-2040/2041/2042 key input. SHR204X-V1.0.0-20050701080[...]

9-34 Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supported at the System Password input. - Use the BACKSP ACE key to delete the contents. Note Note Default System Password is set to 4321. Note Note - If you change the Data/T ime value, SHR-2040/2041/2042 automatically cuts the connection with Smart V i[...]

SHR-2040/2041/2042 USER’S MANUAL 9-35 Note Note The change of language by the system language results in the change of language expression setup of SHR-2040/2041/2042. In short, the language setup of Smart V iewer does not change. Language specification to be supported is subject to change later . - Language Language sets the language in which on[...]

9-36 Note Note If you install the remote control device to the main body of SHR-2040/2041/2042 and activate the setup, PTZ control is not available in the V iewer . - Remocon (Remote Control Device) Remocon can set the remote control device installed to SHR-2040/2041/2042. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-36[...]

SHR-2040/2041/2042 USER’S MANUAL 9-37 @ Camera - Config. Config. sets Video, Audio On/Off, Camera T itle, and Auto Sequence T ime for each channel of on-line SHR-2040/2041/2042. Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supported for title input. - Use the BACKSP ACE key to delete the contents. Cau[...]

9-38 - PTZ device It sets Camera ID, Protocol, Baud Rate, Parity , Data Bit, Stop Bit, and Serial Mode when connecting the dome camera to all the channels. # Monitoring - Monitoring It sets both the event monitoring and OSG display of the live mode. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-38[...]

SHR-2040/2041/2042 USER’S MANUAL 9-39 - Video size Rec. Sets the Video size. The Video size being set in the menu af fects to the ips setup of Rec. Mode and Event Rec. $ Recording - Rec. Mode It sets the Video Size, Quality , and Rate values during the recording by the setting the recoding ON/OFF for the related channel in the live mode. Note Not[...]

9-40 - Event Rec. It sets the Video Size, Quality , Rate, Pre Alarm, and Post Alarm values to be recorded when an event occurs. Note Note Full D1(L) V ideo Size does not support 15ips, 10ips(NTSC)/12.5ips, and 8.33ips(P AL) Rate. NTSC PA L 25 25 25 25 SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-40[...]

SHR-2040/2041/2042 USER’S MANUAL 9-41 - Alarm Rec. It sets the information necessary for the alarm recording. - Motion Rec. It sets the information necessary for the recording by the motion Detection. Note Note More than one camera should be selected to apply the alarm. SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-41[...]

9-42 - Video Loss V ideo Loss sets up the information on how to inform the user of V ideo Loss of SHR-2040/2041/2042. % Network - Password It sets the password for Admin and User when connecting with SHR-2040/2041/2042 through the network in Smart Viewer . Caution Caution - Network password should be composed of numeric and it can be input up to 8 [...]

SHR-2040/2041/2042 USER’S MANUAL 9-43 Caution Caution - Be sure to inquire the network manager before you input Network IP , Gateway , Subnet Mask, and DNS. - Both ADSL ID and Password can be input up to 40 digits of alphabets, numbers, and symbols without discrimination. Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the k[...]

9-44 ● Callback - Y ou can set the Callback function of SHR-2040/2041/2042. - In the event of Alarm, Motion Detection, or Video Loss, set the IP address and port of PC where SmartViewer is installed to forward Callback messages. In failure of message forwarding, set the value for retrial. ● T ransfer Protocol - Y ou can change the transfer prot[...]

SHR-2040/2041/2042 USER’S MANUAL 9-45 Note Note - SHR-2040/2041/2042 uses 4 ports for TCP connection. - The PORT number is flexible and 4 consecutive numbers are grouped for the change ( 554,555,556,557 ➝ 558,559,560,561 ) - If you use the IP Router for network composition, you should allocate a protocol for SHR-2040/2041/2042. V iewer Setup - [...]

9-46 ● V ideo Recording ! Naming - Being connected to SHR-2040/2041/2042 in the monitoring or search mode, you can save the video displayed with .dvr file and name it. - If you set to “Camera No. + Serial No.”, the file name depends on the camera number and serial number . If set to “Camera No. + Date”, it depends on the camera number , c[...]

SHR-2040/2041/2042 USER’S MANUAL 9-47 ● Sequence T ime - When connecting with SHR-2040/2041/2042 in the monitoring mode, set the auto sequence time if the auto sequence is set. The time can be set from 10 to 20 minutes. ● OSD Display - Sets if OSD shall be displayed on each channel of Smart Viewer . - Whether you check “Enable” or not, OS[...]

9-48 Site Setup - Click the [Site Setup] button for Site Setup. - The information of DVR(SHR-2040/2041/2042) or Site that you want to connect by Smart Viewer is set in the Site Setup. - Smart Viewer allows you to connect with DVR(SHR-2040/2041/2042) or Site registered only here. 1 3 5 2 4 ! The DVR(SHR-2040/2041/2042) list that registered by the us[...]

SHR-2040/2041/2042 USER’S MANUAL 9-49 ● DVR List - The information of DVR(SHR-2040/2041/2042) that you want to connect by Smart Viewer is set in the DVR List. - Y ou can register a new DVR(SHR-2040/2041/2042) or delete and edit the DVR(SHR-2040/2041/2042) selected from the registered list, and the name and IP / MAC Address of the registered DVR[...]

9-50 ! To add a new DVR(SHR-2040/2041/2042) - If you press the [New] button, the following window will pop up where you are able to add a new DVR(SHR-2040/2041/2042) information. 1. Network Modes - LAN - If DVR(SHR-2040/2041/2042) is connected to the LAN, set the network mode to LAN. - If the LAN connected to DVR(SHR-2040/2041/2042) uses Static IP [...]

SHR-2040/2041/2042 USER’S MANUAL 9-51 2.Network Modes - ADSL - If DVR(SHR-2040/2041/2042) is connected to the ADSL, set the network mode to ADSL. - If the ADSL connected to DVR(SHR-2040/2041/2042) uses Static IP , select Static IP in the Address T ype and input the name and IP Address of DVR(SHR-2040/2041/2042). - Y ou should select a PORT in acc[...]

9-52 Note Note - The MAC address of DVR is written at the side label of the product. It is also found in the system information of DVR Menu. - If the DVR(SHR-2040/2041/2042) is connected to ADSL, the network bandwidth is low . Therefore, the transfer rate becomes low and the viewer operates in the more limited range. - The viewer can monitor up to [...]

SHR-2040/2041/2042 USER’S MANUAL 9-53 # To Edit the old DVR(SHR-2040/2041/2042) - If you select a DVR(SHR-2040/2041/2042) in the DVR list to edit and press the [Edit] button, the following message box pops up. Press [OK] button to edit the DVR(SHR-2040/2041/2042). - When the DVR(SHR-2040/2041/2042) to edit is connected with the Smart V iewer , th[...]

9-54 ● Site List - Y ou can register and control the many DVRs(SHR-2040/2041/2042) to be connected with the smart viewer at once with a site in the site list. Y ou are allowed to register a new site ,and delete or edit the selected site in the registered list. Also, you can add or delete a DVR(SHR-2040/2041/2042) to the site selected in the site [...]

SHR-2040/2041/2042 USER’S MANUAL 9-55 @ To delete an old site or DVR(SHR-2040/2041/2042) - If you select a site or DVR(SHR-2040/2041/2042) in the site list for deletion and press the [Delete] button, the following message box pops up. Press the [OK] button to delete either site or DVR(SHR-2040/2041/2042). - When deleting the DVR(SHR-2040/2041/204[...]

9-56 - If you select a DVR(SHR-2040/2041/2042) and press the [Edit] button, the following message box pops up and the DVR(SHR-2040/2041/2042) cannot be edited. T o edit the DVR(SHR-2040/2041/2042), go to the DVR list. ● To add a DVR(SHR-2040/2041/2042) to the site - If you press the [Add] button, the DVR(SHR-2040/2041/2042) selected in the DVR li[...]

SHR-2040/2041/2042 USER’S MANUAL 9-57 S/W V ersion - If you press the [S/W V ersion] button, the smart viewer version, system require- ments, and the version of DVR(SHR-2040/2041/2042) System S/W , being connected to the smart viewer , are displayed. - Y ou can upgrade the on-line DVR(SHR-2040/2041/2042) System S/W remotely . Y ou are authorized [...]

9-58 ● Smart Viewer V ersion - Smart Viewer V ersion and system requirements are displayed. ● DVR V ersion - DVR V ersion not only displays the connected DVR(SHR-2040/2041/2042) name if any DVR(SHR-2040/2041/2042) is being connected with Smart Viewer or the name of DVR(SHR-2040/2041/2042) composing a site if any DVR(SHR-2040/2041/2042) is being[...]

SHR-2040/2041/2042 USER’S MANUAL 9-59 @ Click the following button to open the “SHR-2040/2041/2042 Firmware” file in format. # Press the [Upgrade] button to transmit a file to the selected DVR(SHR- 2040/2041/2042) and start the upgrade of DVR(SHR-2040/2041/2042) S/W . $ The progress of file transmission and upgrade is displayed at the bottom.[...]

Appendix 10 SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-60[...]

1 Pr oduct Specification 10-1 SHR-4160N/P USER’S MANUAL Item Details Remarks CPU 32bit RISC CPU Memory SDRAM : 128MByte Flash : 16 MByte OS Embedded OS Broadcasting NTSC System Input V oltage 2040-DC 12V , AC 1 10-220(NTSC), AC 1 10-230(P AL) 2041/2042 - AC 1 10-220(NTSC) AC 100-230(P AL) Power Consumption 2040 : 30W att, 2041 : 60W att, 2042 : 5[...]

10-2 Item Details Remarks Compression Video : MPEG4 Method Audio : ADPCM Resolution Quality Level Max Image Rate V ery High CIF(C) High 352X240(NTSC) Standard /352X288(P AL) Low V ideo Size & V ery High Performance Half D1(N) High 720X288(NTSC) Standard / 720X288(P AL) Low Recording V ery High Full D1(L) High 720X480(NTSC) Standard / 720X576(P [...]

SHR-2040/2041/2042 USER’S MANUAL 10-3 Item Details Remarks Calendar Event - Normal, Schedule, Alarm, Motion, Video Loss Search Mode Date/T ime Go to First Go to Last Backup Data Decoding Performance 1Ch 4Ch Play Back Video size & CIF 30ips(NTSC)/25ips(P AL ) 30ips(NTSC)/25ips(P AL)/1CH Performance Half D1(N) 15ips(NTSC)/12.5ips(P AL) 15ips(NT[...]

2 The specification of HDD and peripheral device 10-4 ● Internal A T A HDD/IEEE1394/USB HDD I/F External HDD Maker RPM Capactity Interface Buffer Series Name Model No Remark 120 GB 160 GB 120 GB Maxtor 160 GB 250 GB W estern 120 GB Digital 160 GB CD-R CD-RW CD-R CD-RW DVD+R DVD-R DVD+RW ❉ DVD-RW is not supported. ● Internal A T A HDD/IEEE1394[...]

SHR-2040/2041/2042 USER’S MANUAL 3 Outline Drawings 10-5 [SHR-2040] [SHR-2041] SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-5[...]

10-6 [SHR-2042] SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-6[...]

SHR-2040/2041/2042 USER’S MANUAL 10-7 4 Factor y Default This restores the Network information and preset values in SHR-2040/2041/2042 to the original state at the time of factory shipment. Factory Default will be done as follows; - Use System / Load Factory Default in MENU or , - If you hold on to the Mode button in Live Mode and keep pressing t[...]

10-8 Classification Detailed Items Factory Setup Duration Off Event Monitoring Date On OSD Display T ime On Monitoring T itle On Status On Spot Out Channel CH1 Spot Out Event Monitor Off Monitor Out Composite Out 1CH DVR Support Off Mode On Record Mode V ideo Size CIF Setup Quality Normal Rate 30ips(NTSC)/25ips(P AL) Continuous Recording Off Event [...]

SHR-2040/2041/2042 USER’S MANUAL 10-9 5 SHR-2040/2041/2042 Smar t V iewer Frame Specification for the Playback FRAME Viewer Screen VIDEO SIZE RA TE Split Mode Half D1(N) CIF (C) Nine-split 1 frame/sec 15 frame/sec Fore-split 15 frame/sec 15 frame/sec Single 15 frame/sec 15 frame/sec Half D1(N) CIF (C) Nine-split 10 frame/sec 10 frame/sec Fore-spl[...]

10-10 Note Note The play frame specification of Smart V iewer varies on the setup of SHR-4160N/P Recording Rate and V ideo Size or the screen split mode of Smart V iewer . The above specification is applicable only when the main body of SHR-4160N/P is connected with a fast network like LAN. When the main body of SHR-4160N/P is connected with a slow[...]

SHR-2040/2041/2042 USER’S MANUAL 10-11 6 Tr oubleshooting(F AQ) 1. The system power is dead and LED in front of the system does not operate at all. - Please check the power connection. - Check the power voltage. - If all your efforts like above end up with nothing, check or exchange the power supply . 2. Video data remains in the system but some [...]

10-12 7. The channel button does not operate in Live. - If the current screen is Event Monitoring, the channel button does not operate. Then, press the Alarm button to terminate the current screen and select a channel. 8. The cursor cannot reach Start during Calendar Search. - Please check both the channel and the date for play are left checked. Bo[...]

SHR-2040/2041/2042 USER’S MANUAL 10-13 13. Smart Viewer in operation is disconnected. - If you change time, network setup, HDD format, Default Setup, or HDD attachment or detachment for SHR-2040/2041/2042 DVR, the current Smart V iewer will be automatically disconnected. - Check network connection. Smart Viewer , if disconnected from Network, wil[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1[...]

SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1[...]

AB68-00517B Correct Disposal of This Product (W aste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. T o pre[...]