Sanyo VCC-6592P manual

INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS VCC-6592P VCC-6594P COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR CCD About this manual • Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. • This manual gives basic connections and operating instructions [...]

1AC6P1P2424-- L53H2, H4/XE (0901KPS-DSP) Sanyo Electric Co, Ltd. Printed in Japan L53H 2, H4 /XE GB 200 1, 9, 18[...]

Depen ding on the co ndit ions of use, instal lation and envir onme nt, please be s ure t o ma ke t he a ppr opriat e sett ing s and adjustm en ts. I f you need hel p wit h insta ll ation a nd/ or se ttings , plea se con sult your de ale r. CONTENTS PRECAUTIONS ........................................................................................[...]

PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For[...]

PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Power input terminal • VCC-6592P: 12 V DC input terminal (12 V DC, GND) • VCC-6594P: 24 V AC input terminal (AC 24 V, AC 24 V, GND) 3 Y/C OUT connector (4 pin) Separate Y (luminance) and C (chroma) [...]

PARTS NAMES 7 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 8 Flange-back adjustment screw (FLANGE BACK ADJ.) 9 Flange-back lock screw (FLANGE BACK LOCK) F Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixin[...]

PARTS NAMES G Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. H Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment [...]

CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates on video si[...]

MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Check the lens mount Do not use a lens if the length “ L ” is more than 5 mm. That may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the c[...]

MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the cabl e at the plug, t hen remove ap pr ox. 8 m m of th e ca ble sh eath an d s trip ab out 2 mm from ea ch wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then cl[...]

CONNECTIONS (VCC-6592P only) Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 12 V DC adaptor. Connect an DC 12 V power source to the 12 V DC input term[...]

CONNECTIONS (VCC-6592P only) Connections to the camera Y/C OUT connector The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Using a coaxial cable (twin type, 75 ohms), connect the Y/C OUT connector from the camera to the S-VIDEO input terminal on the monitor or time lapse VCR. 2 Use a commercially available 12 V DC [...]

CONNECTIONS (VCC-6594P only) Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), AC adaptor and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 24 V AC adaptor. Connect an AC 24 V power source to the AC 24 [...]

SETTINGS (VCC-6592P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. * The sticker on the inside of cover. Cont[...]

SETTINGS (VCC-6594P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. * The sticker on the inside of cover. Cont[...]

SETTINGS Electronic shutter settings and electronic iris settings When all of these switches are down, electronic shutter (1/50 sec or auto iris setting) is enabled. The electronic shutter can be set to one of 7 speeds as shown in Table A . Furthermore, when all switches are up, electronic iris setting is enabled. Notes on the electronic shutter: ?[...]

SETTINGS Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 ( MULT ) and 7 ( CENT ) are set to the down ( OFF ) position. Change the backlight compensation switch settings depending on the conditions. • MULT mode: Use this position when applying backlight compens[...]

SETTINGS White balance adjustment Normally the switch 8 ( WB ) is set to the down ( ATW : auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 ( WB ) to the up ( M : manual) position, then adjust the colour. • Turn RED (VR302) to s[...]

SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window. • If the subject backgroun[...]

TROUBLESHOOTING Bef ore taking the c ame ra for re pair s, plea se check be low to ma ke sure tha t the ca mera is used corre ctly . I f it st ill do es not p erfo rm corre ctly, pl ease consul t yo ur d ealer or a S anyo Aut horized S ervice Ce n tr e. No picture on the monitor screen • Is the po wer turn ed o n to all connec ted devices ? I s t[...]

SPECIFICATIONS Camera: Scanning system : PAL standard (625 TV lines, 25 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 795 (H) x 596 (V) Effective picture elements : 752 (H) x 582 (V) Synchronizing system : Internal sync, External sync automatic switchable (VCC-6592P only) Internal[...]

SPECIFICATIONS Dimensions Features and specifications are subject to change without prior notice or obligations. 12.6 22.4 11 0.5 109 100 1/4 ”– 20 UNC 56 45 28 56 45 28 (VCC-6592P) (VCC-6594P) L53H2, H4/ XE GB 2001, 9, 18 20 English[...]