Sears 113.298141 manual

[Sears ! owners manual MODEL NO. 113.298141 SAW ONLY 113.298031 SAW WITH LEGS TWO TABLE EXTENSIONS AND MOTOR 113.298151 SAW WITH LEGS ONETABLEEXTENSION AND MOTOR Serial Number. Model and serial number may be found at the left-hand side of the base. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL [...]

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty gives yo[...]

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS WARNING: FOR YOUR OWN SAFETY, DO NOT OPERATE YOUR SAW UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS ... AND UNTIL YOU HAVE READ AND UNDERSTOOD THE FOLLOWING. 1. GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS... SEE PAGE 2 2. GETTING TO KNOW YOUR SAW ... SEE PAGE 20 3. BASIC S[...]

R. DO NOT remove small ;)ieces of cut-off material that may become trapped inside the blade guard while the saw is running. This could endanger your hands or cause a kickback. Turn saw "OFF" and wait until blade stops. S. Use extr_ care when ripping wood that has a twisted grain or is twisted or bowed it may rock on the table and/or pinch[...]

Plug power cord into 110-120V properly grounded type outlet protected by a 15-amp. time delay or Circuit-Saver fuse or circuit breaker, IF YOU ARE NOT SURE THAT YOUR OUTLET IS PROPERLY GROUNDED, HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN. WARNING: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUG WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM T[...]

UNPACKING AND CHECKING CONTENTS TOOLSNEEDED Medium Screwdriver Small Screwdriver P, ie , , Wrenche I,I.:,:I',I.I_i, II'Z_ 3/8 in. 7/16 in. 1/2 in. 9116 in. Combination Square 3/4 in. Model 113,298141 Table Saw is shipped complete in one carton but DOES NOT INCLUDE Table Extension, Steel Legs, or motor. Model 113.298031 Table Saw is shippe[...]

Item Part Name Qty. Z Hex Nut, 5/16-18 (approx. dia. of hole 5/16 in.) ........... 9 Z Hex Nut, 1t4-20 (approx. dia. of hole 114 in.) ............ 2 AA Lockwasher, 5/I 6 in. External Type (approx. die. of hole 5116in.) ........... 11 AA Lockwasher, 1/4 in. External Type (approx. alia. of h ale 1/4 in.) ............ 2 AA Lockwasher No. 10 External T[...]

4. To remove insert. A) Loosen Screw B) Lift insert from front end, and pull toward front of saw, To replace insert. Place insert into insert opening in table and push toward rear of saw to engage spring clip and until keyslot in insert will drop over screw. Tighten screw. Do not tighten screw to the point where it will deflect the insert. CHECKING[...]

MOUNTING SAW 1. From among the loose parts, find the following hardware: 4 Hex Head Screws. 5/16 - 18 x 1-1/4 in. long. 4 Hex Nuts, 5/16- 18 (approx. dia. of hole 5/16 in.) 4 Lockwashers, 5/16 in. External Type (approx. dia. of hole, 5/16 in.) 8 Flat Washers, (dia. of hole 11/32 in.) 2. Place saw on legs so that holes in bottom of saw line up with [...]

Lay REAR FENCE GUIDE BAR on table to act as a straightedge. If outer edge of extension is higher or lower than table surface; A. Slightly loosen nuts holding bracket to extension using 7/16 in. wrench. B. Move end of extension up or down until outer edge is even with table surface ... check with GUIDE BAR .., tighten nuts. C. Recheck INNER edge of [...]

9, Nold rod with one hand and with a 1/2 in. wrench or pliers start screwing on ONE of the nuts only A TURN OR TWO... screw on other nut the same way. 10. Using TWO 1/2 in. wrenches or pliers tighten both of the nuts. 1 I. Slide the bars so that screws are in the MIDDLE of the slotted holes. 12. Position rip fence over miter gauge groove, holding u[...]

ALIGNING RIP FENCE The fence should slide easily along the bars and always remain in alignment (parallel to sawblade and miter gauge grooves). The alignment is maintained by a spring underneath the fence which bears against the front guide bar, To move the fence, loosen the lock handle and grasp the fence with one hand at the front. For very close [...]

If the fence does not slide easily along the bars, the pressure of the spring can be REDUCED. 1. Loosen the screws. 2. Move spring slightly toward rear of fence ... tighten screws. 3, The rip fence must be PARALLEL with the sawblade (see page 29) and miter Gauge grooves... Move fence until it is along side of groove. Do NOT LOCK IT. It should be pa[...]

INSTALLING BLADE GUARD 1. From among the loose parts, find 2 Hex Head Screws, 1/4 - 20 x 5/8 in. long 2 Hex Head Screws, 5/16 - 18 x 5/8 in. long 2 Hex Head Screws, 5/16 - 18 x 1 in. long 2 Hex Nuts, 1/4 - 20 (approx. dia. of hole 1/4 in.) 2 Lockwashers, 1/4 in, External Type (approx. dia. of hole 1/4 in.) 2 Lockwashers, 5/16 in. External Type (app[...]

9. Raise blade all the way up . .. make sure it is _quare with table. 10. Raise Blade Guard ... lift up both ANTIKICKBACK PAWLS ... insert one of the SETSCREW WRENCHES in the notches to hold the pawls out of the way, 11. Lay blade of square or other straightedge alongside of blade. 12. Loosen Hex Head Screw in GUARD SUPPORT and move spreader so tha[...]

16. Place RIP FENCE on table ... CAREFULLY move it against blade so that it is parallel to the blade, and just TOUCHES tips of saw teeth ... tighten RIP FENCE LOCK KNOB HANDLE. 17. Insert folded paper between SPREADER and FENCE... hold spreader flat against fence.., tighten screws using 7/16 in. wrench, Now tighten Hex Hd. Screws in Support. 18. To[...]

11. Lift motor and insert the TWO PINS on motor base into HOLES in cradle ... push motor in as far as it will go. 12. Lower the blade...install belt on saw pulley and motor pulley. 13. Sight along edges _ of both pulleys arid move motor pulley so that belt is parallel to the edges of both pulleys...tighten the setscrew in the motor pulley. 14. IMPO[...]

INSTALLING BELT GUARD 1. Remove the belt and motor pulley. 2. Screws furnished witli guard are "self threading" ... screw them into holes in BELT GUARD SUPPORT BRACKET, then remove them. 3. Position BELT GUARD SUPPORT BRACKET and BELT GUARD SUPPORT as shown and install the screws ... make sure motor shaft is in CENTER of hole in SUPPORT. [...]

Press guard onto support so that bottom of guard is approximately 3/4 in. away from belt. NOTE: To remove guard, lift up on LONG TABS of cl ps ... pull guard outward. The clips should remain on the BELT GUARD SUPPORT. 1 3/_ IN. PLUGGING IN MOTOR 1. From among the loose parts, find two wire ties 2. Route motor cord along right side of cabinet and sn[...]

GETTING TO KNOW YOUR SAW _1 SAWSLADE TABLE INSERT MITER GAUGE |0 EXACT-I-CUT LOCK HANDLE 6 MITER GAUGE 7" BLADE GUARD ANTIKICKBACK PAWLS RiP FENCE RIP FENCE LOCK HANDLE 4 TILT LOCK HANDLE (UNDERNEATH TABLE) 2 ELEVATION HANDWHEEL 1 ON-OFF SWITCH 1 ON-OFF SWITCH CAUTION: Before turning switch on, make sure the blade guard is correctly instal[...]

2 ELEVATION HANDWHEEL... elevates or lowers the blade. Turn clockwise to elevate ... counterclockwise to lower, 3 TILT HANDWHEEL ... tilts the blade for bevel ' cutting. Turn clockwise to tilt toward left ... counterclockwise to tilt toward right, When the blade is tilted to the LEFT as far as it will go, it should be at 45 ° to the table and[...]

9 REMOVING AND INSTALLING SAWBLADE. WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTAL LING SAWBLADE. A. Raise Blade Guard...remove insert. B. To REMOVE blade, place a block of wood against front of blade ... PULL arbor wrench toward you to LOOSEN arbor nut. / / WOOD BLOCK OR[...]

BASIC SAW OPERATION WORK HELPERS Before cutting any wood on your saw, study all of the "Basic Saw Operations". Notice that in order to make some of the cuts, it is necessary to use certain devices "'Work Helpers" like the Push Stick, the Push Block and the Auxiliary Fence/Work Support, which you can make yourself. After you[...]

CROSSCUTTING CROSSCUTTING is known as cutting wood across the grain, at 90 °, or square with both the edge and the flat side of the wood, This is done with miter gauge set at "'O". The graduations on the miter gauge provide accuracy for average woodworking. In some cases where extreme accuracy is required, when making angle cuts, fo[...]

1. NEVER USE THE RIP FENCE AS A LENGTH STOP BECAUSE THE CUTOFF PIECE COULD BIND BETWEEN THE FENCE AND THE BLADE CAUSING A KICKBACK, 2. When making repetitive cuts shorter than 6 in., clamp a block of wood 2 in. long to the table to act as a length stop. Do not clamp directly to the bottom edge of the table because the "swivel" of the clam[...]

USING THE RIP FENCE RIPPING, BEVEL RIPPING, PLOUGHING, MOLDING, not DIG into the workpiece and HOLD it... the pawls RESAWING AND RABBETING are performed using the must be SHARPENED. See "Maintenance" section. RIP FENCE together with the AUXILIARY 5. Have blade extend approximately 1/8 n. above top of FENCE/WORK SUPPORT, PUSH STICK OR PUSH[...]

When "WIDTH OF RIP" is 2 in. to 6 in, wide USE THE PUSH STICK to feed the work. When WIDTH OF RIP is NARROWER than 2 in., the push stick CANNOT be used because the guard will interfere. _. USE the AUXILIARY FENCE_WORK SUPPORT and PUSH BLOCK. Attach Auxiliary Fence/Work Support to rip fence with two "'C'" clamps. Feed t[...]

RESAWING RESAWING is known as ripping a piece of wood through its thickness. Do not attempt to resaw BOWED or WARPED material. NOTE: To RESAW a piece of wider than 3-3/8 in .... it will be necessa blade guard ... and use the AUXILIARY FENCE/WORK SUPPORT. (See "Work Helpers"). Clamp it to the table so that the workpiece wil SLIDE EASILY bu[...]

ADJUSTMENTS WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. BAR LOCK KNOB STOP PIN MITER GAUGE NOTE: The slots for the stop pin and the graduations are manufactured to very close tolerances which provide accuracy for average woodworking. In some cases where extreme ac[...]

6. If tooth does not touch the same amount ... the mechanism underneath must be adjusted to make the blade PARALLEL to GROOVE. A. Rear trunnion must be moved TOWARD the combination square if there is a space between marked tooth and end of square in step 4, B, Rear trunnion must be moved AWAY from the square if marked tooth pushes square out of pos[...]

3. Operate the tilt-lock handle (COUNTERCLOCKWISE) to loosen the tilt clamp screw. 4. NOTE: Handle is spring loaded for engagement with screw head - must be pushed inward for disengagement whenever necessary to obtain a new grip on screw head. Rotate tilt handwheel CLOCKWISE a few turns to till blade. Now rotate handwheel COUNTERCLOCKWISE until it [...]

If b! ade is NOT 45 ° to table.., the 45 ° STOP COLLAR and SCALE must be ADJUSTED, _ 1 Remove Elevation Handwheel. _ 0 ° 2. Using a small size screwdriver, reach thru curved slot in front trim panel and loosen BOTH setscrews in 45 ° STOP COLLAR. TILTNOTE: 'f Y°u can't reach the setscrews' turn theHANDWHEELs,,ght,y. __ _i! _ 3. R[...]

LUBRICATION The following parts should be oiled occasionally with SAE No. 20 or No. 30 engine oil. 1. Tilt screw threads and pivot nut. (First Clean with Craftsman Gum & Pitch Remover.) 2. Elevation screw threads and pivot nut. (First Clean with Craftsman Gum & Pitch Remover.) 3. Cradle bearing points. 4. Bearing points in guard assemblv, m[...]

TROUBLE SHOOTING WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLESHOOTING. TROUBLE SHOOTING -- GENERAL TROUBLE , PROBABLE CAUSE Excessive vibration. 1_ Blade outof balance. | 2. Damaged V-Belt Pulleys or poor belt. Cannot make square ' 1. Miter gauge not adjusted Cut when [...]

TROUBLE SHOOTING -- MOTOR (Continued) TROUBLE Motor starts slowly or fails to come up to full speed. 3. I Motor overheats. 1. 2. Starting switch in motor will not operate. 3. Motor stalls 1. (resulting in blown fuses or tripped circuit breakers). Frequent opening of fuses or circuit breakers. PROBABLE CAUSE 1, Low voltage will not trip relay. 2. Wi[...]

o, 1 6 3 PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 7 8 9 10 14 16 20 19 36 35 28 29 30 31 32 31 ! Figure I 33 27 26 25 i -I[...]

(,} PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 Always order by Part Number - not by Key Number. FIGURE 1 PARTS LIST Key Part No. No. Description 1 62579 2 STD 522506 3 STD 551225 4 STD 541025 5 STD 523110 6 62541 7 STD 551231 8 STD 541031 9 60388 10 62703 11 62718 12 STD 501102 13 133645 14 62748 15[...]

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 12 3 4 5 6 7 65 64 62 44 45 43 9 10 12 13 14 31 41 4O 18 19 20 I u t 25 I 38 37 36 21 1 Figure 2[...]

_O PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 FIGURE 2 PARTS LIST Key Part No. No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 62587 60204 STD 571812 STD 523106 STD 523110 STD 551231 62292 STD 541031 STD 532507 60206 60205 STD 551037 63011 62[...]

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 9 10 11 2 3 4 5 I 13 FIGURE 3 -- 62705 FENCE ASSEMBLY Key { Part No. No. Description - 62705 1 62693 2 62692 3 STD 551031 4 62711 5 60049 6 62527 423350 8 62582 9 STD 600805 10 62528 11 62529 12 62531 1_ 625_3 14 • 62533, 15 STD 551210 16 STD 611005 17 62[...]

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 14 FIGURE 4 -- 62704 MITER GAUGE ASSEMBLY Key Part No. No. Description - 62704 1 62693 2 62692 3 8 9 10 11 12 13 14 STD 551031 37893 STD 510803 135 37895 37896 9417295 62230 8TD 541231 62225 62383 60288 +Gauge Assembly, Miter Plug, Button Knob, Miter Gauge [...]

PARTS LJST FOR CRAFTSMAN 10 INCH TABLE SAW MODEL NO. 113.298141, 113.298031 & 113.298151 1 2 5 3 4 FIGURE 6 -- ON/OFF POWER OUTLET 60381 6 Kev l No. J 1 2 :3 _i 4 5 6 • Paff- No. 60381 60375 60380 60256 60374 60377 448007 Description • On/Off Power OutletComplete Cord, Molded Housing, Switch Key, Switch Switch, Locking Cover, Switc h Sc[...]

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW MODE L NO. 113.298141, 113.298031 & 113.298151 4 5 5 4 12 2, FIGURE 8 -- LEGS SUPPLIED WITH 113.298031 AND 113.298151 ONLY Key No, 1 2 3 4 5 6 7 8 Part No. Description 60314 Screw, Serrated Truss Hd. 1/4-20 x 5/8 62552 Leg 62554 Stiffener, Side STD 551225 * Lockwasher, Ext. 1/4 STD 541025 *Nut, Hex 1/4[...]

Sears I owners manual SERVICE MODEL NO. 113.298141 SAW ON LY 113.298031 SAW WITH LEGS TWO TABLE EXTENSIONS AND MOTOR 113.298151 SAW WITH LEGS ONE TABLE EXTENSION AND MOTOR HOW TO ORDER REPAIR PARTS 10 INCH TABLE SAW Now that you have purchased your 10-inch table saw should a need ever exist for repair parts or service, simply contact any Sears Serv[...]