Simplicity 1691414 manual

O PERATOR ’ S M ANUAL Sno-Away Models 5-55cd22 7-55cd22 Mfg. No. 1691411 Mfg. No. 1691413 Mfg. No. 1691414[...]

BakerTM O PERATOR ’ S M ANUAL Model 7/22E[...]

II 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI 53074-0997[...]

[...]

Table Of Contents SAFETY RULES General ........................................................... 2 Preparation.. .................................................. .2 Operation.. ..................................................... .2 Maintenance & Storage.. .............................. .3 Safety Decals ....................................[...]

WARNING This unit is a “two-stage” snowthrower. The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur. To avoid injury, keep [...]

Safety Rules l Always refer to the Operator’s Manual for important details if snowthrower is to be stored for an extended period. l Run auger drive a few seconds after completion of throwing snow to help clear out snow and prevent freeze-up. SAFETYDECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant remi[...]

Controls SNOWTHROWER CONTROLS (Figure 1) Ref A B i C D E Name Auger Control Clutch Lever Drive Control Clutch Lever Chute Control Rod Chute Deflector Skid Shoes Function Engages auger/impeller when depressed; disengages when released. Engages drive to wheels when depressed; disengages when released. Controls direction snow is thrown. Controls angle[...]

DEFLECTOR The angle and distance of the discharged snow is con- trolled by the position of the deflector. Engine speed also affects distance of discharge. The more the deflector is tilted back, the farther snow will be thrown. Loosen the knob (figure 3) to tilt the deflector back or forward, then retighten the knob. SCRAPER BAR & SKID SHOES On [...]

Operation GENERAL I A WARNING A WARNING Before leaving the operator’s area for any reason, stop the engine and remove the key. Disconnect the spark plug wire and secure it away from the plug to prevent accidental start-up of the snowthrower. Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot 1 f[...]

Operation 7. As the engine warms up and begins to operate even- ly, turn the choke knob slowly counterclockwise to the OFF position. If engine falters, return to l/2 choke position until it runs smoothly, then turn it to the choke OFF position. NOTE: Allow the engine to warm up for a few minutes before operating the snowthrower. Engine will not dev[...]

Regular Maintenance NORMAL CARE I Every 25 Care Reauired See Paae Hours -a Check auger gear case lubrication.* Page 8 . I Lubricate snowthrower. Paae9 I . 1 Check tire pressure. I Paae 9 I l I 1 Change engine oil.**+ Clean or replace spark plug.+ . I I . i I Check discharge control. 1 Page 14 I I * I * The transmission and auger gear case have been[...]

Regular- Maintenance LUBRICATION CHECKING TIRE PRESSURE A CAUTION It is very important that grease fittings on auger shaft (figure 6) are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. With an oil can, apply medium weight (IOW) oil to points A & i3 shown in figure 7. There are two grease[...]

A WARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent acciden- tal starting, disconnect the spark plug wire and fasten away from the plug. This section provides troubleshooting and service instructions. For problems not covered here, contact your dealer. T[...]

SHIFT CONTROL ADJUSTMENT If any of the following conditions exist, it will be neces- sary to adjust the shift control. l Snowthrower is not in neutral when shift lever is in NEUTRAL position. l Reverse position cannot be fully reached. l 3rd gear cannot be fully reached. Adjust as follows: 1. Locate neutral position of shift lever by moving unit ba[...]

Adjusting Drive Belts If the auger or wheels slip under load, belts could be stretched or worn. Adjust as follows: 1. Remove the belt cover (figure 10). Determine which belt requires adjustment. 2. Loosen the locknut on the appropriate idler pulley and move the idler pulley i/4” toward the belt (figure 11). Tighten the locknut. 3. Re-install the [...]

A CAUTION Place a block (approximately 4” high) under front edge of auger housing or snowthrower will not stand on end. 6. See figure 13. Loosen nuts holding lower belt guard and slide guard away from belt. 7. Remove belt from between large pulleys. 13. Slide new belt onto pulley and position lower belt guard to within l/16” - i/8” of large d[...]

WHEEL AXLE BEARING REPLACEMENT After approximately 100 hours of use (about 5 years), or if drive chain jumps off sprockets, wheel axle bearings may need to be replaced. 1. Disconnect spark plug wire and fasten it away from the spark plug. 2. Place a block under the snowthrower so the wheels are just off the ground. 3. See figure 16. Remove the ring[...]

Specifications ENGINE Make ................................................................ Tecumseh Cylinders.. ..................................................................... .1 Cycles ............................................................................. 4 Crankshaft ....................................................... Horizontal[...]

Replacement Parts %I Accessories COMMON REPLACEMENT PARTS Listed below are part numbers for the more common replacement parts. Use only genuine Simplicity replace- ment parts to assure optimum performance and safety. Special Worm Gear Oil for Auger Gear Case - 8 oz. Container.. .............................................. .1704636 - Case of 8 oz.[...]