Simplicity 1694584 319E manual

Print V endor Instructions Ho w to use this file Operator’ s Manuals P aper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent • Cov er - on pre-printed two tone “Sw ash” stock. Press: • Body - 1 color , 2-sided • Cov er - 1 color , 1 sided Bindery: • Saddle stitch, face trim *if too thic k f or saddle stitch, tape[...]

THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT)[...]

OPERA T OR’S MANU AL Single Sta g e Sno wthr o wer 319M Models Mfg. No. Description 1694583 319M, 3HP Snowthrower, Manual Start 319E Models Mfg. No. Description 1694584 319E,3HP Snowthrower, Electric Start Manual No. 1727190 Rev 4/2004 TP 100-4091-00-SW-S[...]

MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004, Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.[...]

1 T able of Contents Safety Rules & Inf ormation Training ...................................................................2 Preperation .............................................................2 Operation .............................................................2-3 Children ............................................................[...]

This machine is capable to amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. S[...]

3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service. 10. Maintain or replace safety and instruction labels as necessary. 11. Keep nuts and bolts tigh[...]

4 ID Tag When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access. These numbers can be found in the locations shown. NOTE: For location of engine ident[...]

5 Safety Decals / Identification Numbers SAFETY DECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the operator of the most important safety precautions. All warning, caution and instructional messages on your snowthrower should be carefully read and obeyed. If any of these decals are lost or[...]

6 Features & Controls CONTR OL LOCA TIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section. NOTE: Throttle -[...]

7 Features & Controls Chute Deflector Control Controls the distance snow is thrown. Tilting the chute deflector UP provides a higher stream and greater dis- tance, while tilting the deflector DOWN provides a lower stream and less distance. Loosen the deflector knob, adjust the deflector, then retighten the knob. Chute Direction Control The chut[...]

8 Operation GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan- sion. See your engine owner’s manual for fuel recom- mendations. 3. Check the auger co[...]

9 FUEL AND OIL MIXTURE The snowthrower uses a two cycle engine that requires a mixture of fuel (gasoline) and oil for lubrication of engine bearings and other moving parts. The correct fuel/oil mixture ratio is 50 to 1. Use fuel/oil mixture chart shown. NOTE: To prevent damage to engine, carefully observe recommended fuel to oil mixing ratio and pr[...]

10 Operation ST ARTING THE ENGINE NOTE: The snowthrower engine is designed to operate at cold temperatures. Avoid operating the snowthrower if air temperature is 40° F or warmer. Engine will be diffi- cult to start in warm weather. 1. Insert engine key into the switch and turn key (B, Figure 2) to the ON position. Make sure the auger control is in[...]

11 Operation OPERA TING THE SNO WTHR O WER Before operating snowthrower, review the CHECKS BEFORE EACH START UP on page 8 of this manual. Refer to FEATURES & CONTROLS for control locations. 1. Rotate the discharge chute to the desired direction. 2. Pull the auger control back against the handle to engage the auger. NOTE: The snowthrower will be[...]

Regular Maintenance 12 CHECK A UGER CABLE & ST OPPING TIME 1. Visually check the cable (C, Figure 3) for kinks, fray- ing, or severed cable strands. Replace if damaged or worn. 2. Start the engine. 3. Engage the auger control (A) and hold for five sec- onds. 4. Release the auger control (A). The auger (B) must stop within 5 seconds or less. If [...]

13 T roubleshooting, Adjustments, & Service PROBLEM PR OBABLE CA USE CORRECTIVE A CTION Engine Will Not Start Using Recoil Starter 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel/oil mix. 2. Engine needs choking & priming. 2. Move choke control to "CHOKE" position. Push primer bulb three times. 3. Spark plug fouled or wire d[...]

14 T roubleshooting, Adjustments, & Service Before beginning any repair stop the engine, remove the key, disconnect the spark plug wire, and wait for all moving parts to stop. W ARNING DO NOT over-tighten the cable. The control cable must have some slack when in the disengaged position for the auger brake to function properly. If the auger does[...]

15 T roubleshooting, Adjustments, & Service DO NOT over-tighten the cable. The control cable must have some slack in the disengaged position for the auger brake to function properly. If the auger does not stop within 5 seconds of the auger control being released, see your dealer. W ARNING A UGER DRIVE BEL T IDLER PULLEY ADJUSTMENT If the auger [...]

Figure 10. Belt Diagram - PTO Pulley A. Belt Guide B. Idler Pulley C. PTO Pulley D. Drive Belt O F F O F F 16 T roubleshooting, Adjustments, & Service A UGER DRIVE BEL T REPLA CEMENT Inspect belt frequently for signs of excessive wear. Visually check for cracking, fraying, severed or exposed belt strands. 1. Remove the side belt cover (D, Figur[...]

17 T roubleshooting, Adjustments, & Service Figure 11. Auger Flites A. Auger B. Flite Shoe C. Self-Tapping Screws A UGER FLITE SHOE REPLA CEMENT Inspect the flite shoes frequently for signs of excessive wear. Visually check flite shoes for cracking, fraying, and severed or exposed belts. 1. Turn the engine OFF, remove the key, disconnect the sp[...]

18 Specification, Parts, & Accessories SPECIFICA TIONS Engine Make Tecumseh Model HSK600 Spec 1691V / 1702V Horsepower* 3 @ 4300 rpm Displacement 6 cu. in. Oil Type 2-Cycle Starter Recoil, or Recoil with Electric Start Chassis Chute Rotation 200 degrees Fuel Tank Cap. 1.25 Qt. Overall Height 36” Overall Width 21” Auger Width 19” Overall L[...]