Smeg ALFA135V6 manual

Table of Contents 1. PRECAUTIONS FOR SAFETY AND US E _____________________ 22 2. INSTALLING THE OVEN __________________________________ 24 3. DESCRIPTION OF CONTRO LS ____________________________ 27 4. USING THE OVEN _______________________________________ 28 5. CLEANING AND MAINTENANCE ___________________________ 34 6. EXTRAORDINARY MAINTENANCE __[...]

Introduction 1. PRECA UTIONS FOR SAFETY AND USE THIS MANUAL IS AN INT EGRAL PART OF THE APP LIANCE. TAKE GOOD CARE OF IT A ND KEEP IT TO HAND TH ROUGHOUT THE OVEN'S LI FE CYCLE. WE URG E YOU TO READ THIS MA NUAL AND ALL THE INFORMATIO N IT CONT AINS CAREF ULLY BEFORE USING THE O VEN. INSTALLATIO N MUST BE CAR RIED OUT BY Q UALIFIED ST AFF IN C[...]

Introduction NEVER PL ACE FLAMMABL E OBJECTS I N THE OVEN: IF IT SHO ULD ACCIDENTALLY BE SWITCHED ON , THIS MIGHT CAU SE A FIRE . THE APPLIAN CE BECOMES VER Y HOT DURING USE. OVEN G LOVES SHOULD ALWAY S BE WORN. THE NAMEPLA TE WITH THE TECH NICAL DATA, SERI AL NUMBER AND MARK IS IN A VISIBL E POSITION ON TH E BACK OF THE OVE N. THIS NAMEP LATE MUST[...]

Instructions for the Installer 24 2. INST ALLING THE O VEN The oven is designed for free-standi ng installation on a horizontal w ork- top. It must be far enough from the wa ll behind it to allow easy access to the terminal board for conne ction of the power supply lead. Installati on must be carried out by a qualified engineer in comp liance with [...]

Instructions for the Installer 25 The power supply lead supplie d is of H07RN-F type, gauge 3 x 4 mm 2 . For operation at 380-415V2N ∼ or 380 - 415V3N ∼ , the power supply cable has to be replaced with one of H07R N-F type. The gauge of the wires in the new cable m ust be at least 2.5-1.5 mm 2 (4 x 2.5 mm 2 -5 x 1.5 mm 2 ), bearing in mind that[...]

Instructions for the Installer 26 2.2 Safety thermosta t The oven is fitted wit h a safety device t ripped in c ase of a seriou s malfunction. To reset the safety dev ice, call the after-sales service. The manufacturer dec lines all responsibility for inju ry or damage caused by failure to comply with t he above regulatio ns or deriving from tamper[...]

Instructions for the User 3. DESCRIPTION OF CONTROLS START BUTTON Use this button to set th e time when turn ing on the appliance for the first time or after a power failur e, scroll through preset programs and start cooking cycles. STOP BUTTON Use this button to set th e time when turn ing on the appliance for the first time or after a power failu[...]

Instructions for the User 28 4. USING THE O VEN 4.1 Precautions and General Advice When the oven is us ed for the first time, it should be heated to the maximum t emperature for lon g enough to burn off any oily residu es left by the manufacturing process. If you have to carry out any procedures on foods, leave the door open for as short a time as [...]

Instructions for the User time, press START + STOP together to return to the point described in section “4.3 Setting the time”. 4.5 Program selection This oven has 15 different cooking program s, including: 14 user-editable programs for humid if ied fan-mode cookin g (P1 to P14); 1 manual editable program for fan-mode cooking. The following tab[...]

Instructions for the User 30 To edit a humidified fan-mod e program by entering the parameters ex actly as required, turn the knob to one of the programs from P1 to P14. The display shows the parameters c ontained in the selected program. Hold down STOP for 2 seconds. A beeper sounds to in dicate that the editing mode has been accessed , and the me[...]

Instructions for the User Press STOP to complete the program editing procedure. The display shows UEnd . The parameters set are now saved i n the chosen program. Press START to display the pa rameters just set. Press START again to run the program just edite d. 4.7 Humidified fan-mode cooking Use the knob to select one of the preset programs (P1 ?[...]

Instructions for the User 32 above, or at the program temperatur e for cookin g operations at belo w 100°C. After 20 minutes, the oven switches off. N.B. - during preheating and cooking, whenever the door is opened the message "door" wil l appear on the display and a beep will sound to war n the user that the door must be clos ed w hile [...]

Instructions for the User 4.9.1 How to use this program Use the knob to select the manual program. The display shows "- - - - " to indicate that there are no cooking parameters present, and the num ber of the pr ogram (P10). Press START or keep it pressed to increase the cook ing temperature; each time START is pressed the temperature inc[...]

Instructions for the User 34 5. CLEANING AND MAINTENANCE Important: never point jets of water str aight at the oven and do n ot use high- pressure water cleaners. Before carrying out any operation, disconnect the oven from the electricity supply. 5.1 Cleaning stainless steel To keep stainless steel in good condit ion, it must be cleaned regularly a[...]

Instructions for the User 5.2 Cleaning the inside of the oven To keep the oven in g ood condition, it must be cl eaned regularly at th e end of each day, after allowing it to cool. Remove all rem ovable parts. Remove the side runners by removing the hook " C " from the hole or pin "D" (depending on the model) and the pin " [...]

Instructions for the User 36 6. EXTRA ORDINAR Y MAINTENANCE Occasionally, the oven will require mi nor servicing proc edures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific oper ations fo r each pr ocedure of this kind are provided below. Before carrying out any operation, disconnect the oven fr[...]

Instructions for the User 6.2 Removing the door Open the door completely and insert the pins (supplied) into the holes from the inside. Close the door to an angle of about 45° and lift it off. To reassemble, fit the hinges into their grooves, then lower t he door into place and extract the pins. 6.3 Oven door gasket To allow thorough cleanin g of [...]