Smeg AP64S3 manual

Contents 24 1 INSTRUCTIONS FOR SAFE AND PROPER USE ____________________ 25 2 POSITIONING OF THE HOB ____________________________________ 27 3 ELECTRICAL CO NNECTION ____________________________________ 29 4 GAS CONNECT ION ___________________________________________ 30 5 ADAPTATION TO DIFFER ENT TYPES OF GAS _____________________ 32 6 FINAL OPER AT[...]

Introduction 25 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WH OLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SUP[...]

Introduction 26 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB. DO NOT PUT PANS WITHOUT PERFECTLY SMOOT[...]

Instructions for the installer 27 2 POSITIONING OF THE HOB The following operation requir es building and /or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials s uch as masonry, metal, solid wood or plastic lamin at ed wood as long as they are heat resistant (T 90°C). 2.1 Attachmen[...]

Instructions for the installer 28 A+B A+B A+B A+B B B Fig.1 2 0÷4 0 B A Fig.2 B A Fig.3 Fig.4 Fig.5[...]

Instructions for the installer 29 3 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power lin e conform to the data shown on the plate located u nder the casing. Do not remove this plate for any reason. The plug on the end of the supply cable an d the wall socket must be the same type and conform to the current electrical syste[...]

Instructions for the installer 30 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance m ay be adjusted laterally. For this purpose, loosen hexagon nut B , [...]

Instructions for the installer 31 4.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisio ns of standards regu lations in force. Make s ure that feed pressure conforms to t he levels shown in t he table in paragraph “ 5.3 Regulation for LPG”. 4.2 Ventilation of rooms The hob may be installed [...]

Instructions for the installer 32 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any clea ning or maintenance work, disconnect the appliance from the electrical socket. The hob has been inspected for G20 (2H) nat ural gas at a pressure of 20 mbar. For functioning w ith other types of gas the nozzl es must be replaced and the primary air a[...]

Instructions for the installer 33 5.3 Regulation for LPG Check that the connectio n has been made as d escribed in the “Gas connection” section. Undo the screw “ D ” and push the air regulator “ C ” fully d own. Use a spanner to remove the nozzles “ B ” and fit those of suitable type following the instructions give n in the tables f[...]

Instructions for the installer 34 5.4 Regulation for natural gas The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work with this type of gas, perform th e same operations described in para graph “ 5.3 Regulation for LPG”, but choose the nozzles and reg ulate the primary air for natural gas, as s[...]

Instructions for the installer 35 5.5 Regulation of primary air Referred to distance “ A ” in mm. 60 cm hobs with separable control panel. Burner G20 20 mbar G30/G31 28/37 mbar Auxiliary (1) 3.0 4.0 Semirapid r (2) 1.0 2.0 Semirapid l (3) 1.0 2.0 Rapid large (4) 1.0 3.5 Ultrarapid (5) 1.0 5.0 90 cm hobs with separable control panel. Burner G20 [...]

Instructions for the installer 36 6 FINAL OPERATIONS Having carried out the above adj ustm ents, reassemble the applianc e following, backwards, the i nstructions in p aragraph “ 5.1 Removing the separable control pa nel / 5.2 Removing the hob”. 6.1 Regulation of minimum for natural gas Reposition the components o n the burner and slide the kno[...]

Instructions for the installer 37 6.3 Arrangement of the b urners on the hob (Hob with separable control panel) 60 cm. hob BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid large 5. Ultrarapid 90 cm. hob BURNERS 1. Auxiliary 2. Semirapid 3. Rapid 4. Fish burner 5. Ultrarapid[...]

Instructions for the installer 38 6.4 Arrangement of the b urners on the hob (Hob with built-in control panel). 60 cm. hob BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid 5. Ultrarapid 6.5 Lubrication of gas taps With time it may happen that the gas taps get blocked and h ard to turn. Clean them inside an d re-grease them. This operatio[...]

Instructions for the user 39 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with wok s (Chinese pans). Adapter D comes only with open grids models and is intended for us e wi[...]

Instructions for the user 40 7.3 Diameter of the pans Burners Ø min. and max. (en cm.) Auxiliary 12-14 Semirapid 16-20 Rapid medio 22-26 Rapid large 22-26 Ultrarapid 22-26 Fish burner Special oval-shaped vessels 7.4 Electric elements 7.4.1 Turning on electric elements Hobs may be fitted with an electric elem ent of varying diameter. The electric e[...]

Instructions for the user 41 WARNING When switching on the electric element for the first time, or if the electric element has not been used for a long time, to rem ove any humidity from the insulating material it should be drie d out by placing the el ectric element on position 1 for 30 minutes. To use correctly remember to: • Switch the electri[...]

Instructions for the user 42 8 CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regularl y every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve t he surf[...]

Instructions for the user 43 8.2 Cleaning of cooking hob componen ts CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the stai nless steel b urner caps and pan- stands tend to be burnishe d by the high temperature. Clea n these parts using very fine abrasive sponges or simil ar commercial products. Then use a specifi[...]