SOYO SY-7IS2 manual

SY-7IS2 Motherboard **************************************************** FC-PGA Socket 370 Processor supported 815EP AGP/PCI/CNR 66/100/133 MHz Front Side Bus supported ATX Form Factor **************************************************** User's Manual[...]

SOYO ™ SY-7IS2 ii Copyright © 2001 by Soyo Computer Inc. Trademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyrights bel[...]

T able of Contents SY-7IS2 iii Table of Contents CHAPTER 1 MOTHERBOARD DESCRIPTION ................................... 1 1-1 INTRODUCTION ............................................................ 1 1-2 HANDLING THE MOTHERBOARD .............................. 3 1-3 ELECTROST A TIC DISCHARGE PRECAUTIONS ......... 3 1-4 SY-7IS2 MOTHERBOARD L AYOUT .[...]

T able of Contents SY-7IS2 iv 3-5 INTEGR A TED PERIPHERALS ..................................... 66 3-6 POWER MANAGEMENT SETUP ................................ 71 3-7 PNP/PCI CONFIGUR A TION SETUP ............................. 75 3-8 PC HEA LTH STATUS .................................................... 78 3-9 LOAD FAIL-SAFE DEFAU LTS .............[...]

Motherboard Description SY-7IS2 1 Chapter 1 MOTHEBOARD DESCRIPTION 1-1 INTRODUCTION Ø The SY-7IS2 AGP/PCI/CNR Motherboard is a high-performance Socket 370 processor supported A TX form-factor system board. SY- 7IS2 uses the 815EP Chipset technolog y . This Motherboard is fully compatible with industry standards Supports Inte l ® FC-PGA processors[...]

Motherboard Description SY-7IS2 2 Ø Supports multiple-boot function Ø AGP 2.0 Compliant; AGP Universal Connector supports: - 1.5V and 3.3V AGP cards - 1X/2X/4X data transfer Ø Supports Communication Networking Riser Slot (CNR 1.0 compliant) * Ø Smart Card Reader - Compliant with Personal Computer Smart Card ( PC/SC ) Working Group standard - Co[...]

Motherboard Description SY-7IS2 3 1-2 HANDLING THE MOTHERBOARD To avoid damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. Ø Remove the Motherboard from its anti-static packaging. Hold the Motherboard by the [...]

Motherboard Description SY-7IS2 4 1-4 SY-7IS2 MOTHERBOARD L AYOUT Back Panel SY-7IS2 Platform USB 1 USB 2 PS/2 K B Connecto r PS/2 Mous e PS/2 Mous e Connector 3 V Lithiu m Battery IDE 1 IDE 2 ATX Powe r PCI# 6 PCI# 5 PCI# 4 PCI# 3 PCI# 1 PCI# 2 Inte l 1 3 CPUFA N 2 1 3 1 4 PR T COM 1 COM 2 AGP Slo t JP 8 1 1 3 3 JP 1 JP3 4 1 4 3 6 VJ 2 1 2 JP 6 1 [...]

Motherboard Description SY-7IS2 5 1-5 SY-7IS2 MOTHERBOARD COMPONENTS A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A A A B A C A D A E[...]

Motherboard Description SY-7IS2 6 A Enable/Disable USB Keyboard Wake Up Jumper B Enable/Disable Power-On by Keyboard Jumper C CPU Voltage Adjust Setting Jumper D Socket 370 Connector E 32-bit AGP slot F Intel FW82815EP Chip G ATX Power Supply Connector H DIMM Bank I CPU Frequency Settings Jumper J Bus Mastering E-IDE/ATAPI Ports K Floppy Disk Drive[...]

Motherboard Description SY-7IS2 7 1-6 CHIPSET The Intel ® 815EP Chipset is a high-flexibility chipset designed to extend from the basic graphics/multimedia PC platform up to the mainstream performance desktop platform. The chipset consists of a Memory Controller Hub (Inte l ® 815EP MCH), an I/O Controller Hub2 (ICH2) for the I/O subsystem, and a [...]

Motherboard Description SY-7IS2 8 l Upstream accelerated hub architecture interface for access to the MCH 1-6.2 Intel ® 815EP MCH Overview The Inte l ® 815EP MCH functions and capabilities include: l Support Uni-processor system l 64-bit AGTL+ based System Bus Interface at 66/100/133 MHz l 32-bit Host Address Support l 64-bit System Memory Interf[...]

Motherboard Description SY-7IS2 9 The SDRAM controller interface is fully configurable through a set of control registers. The Inte l ® 815EP MCH supports industry standard 64-bit wide DIMMs with SDRAM devices. The thirteen multiplexed address lines. SMAA[12:0], along with the two bank select lines, SBS[1:0], allow the Inte l ® 815EP MCH to suppo[...]

Motherboard Description SY-7IS2 10 The AGP interface supports 4x AGP signaling. AGP semantic (PIPE# or SBA[7:0]) cycles to SDRAM are not snooped on the host bus. AGP FRAME# cycles to SDRAM are snooped on the host bus. The MCH supports PIPE# or SBA[7:0] AGP address mechanisms, but not both simultaneousl y . Either the PIPE# or the SBA[7:0] mechanism[...]

Motherboard Description SY-7IS2 11 1-6.7 IDE Support The motherboard has two independent bus-mastering PCI IDE interfaces. These interfaces support PIO Mode3, PIO Mode 4, PIO Mode 5 ATAPI devices (e.g., CD-ROM), and Ultra DMA 33/66/100 synchronous-DMA mode transfers. The BIOS supports logical block addressing (LBA) and extended cylinder head sector[...]

Motherboard Description SY-7IS2 12 1-6.8 Real-Time Clock The real-time clock supports 256 bytes of battery-backed CMOS SRAM. Hardware implementation to indicate century rollover. 1-7 I/O INTER FACE CONTROLLER The motherboard uses the ITE IT8712F-A I/O controller which features: l Single diskette drive interface l Two serial ports l FIFO supports on[...]

Motherboard Description SY-7IS2 13 program, the diskette drive interface can be configured for the following diskette drive capacities and sizes. l 360 KB, 5.25-inch l 1.2 MB, 5.25-inch l 720 KB, 3.5-inch l 1.2 MB. 3.5-inch (driver required) l 1.25-1.44 MB, 3.5-inch l 2.88 MB, 3.5-inch 1-7.4 PS/2 Keyboard and Mouse Interface PS/2 keyboard and mouse[...]

Motherboard Description SY-7IS2 14 1-8 HARD WARE MONITOR The optional hardware monitor subsystem provides low-cost instrumentation capabilities. The features of the hardware monitor subsystem include: Ø An integrated ambient temperature sensor Ø Fan speed sensors, which monitor the fan 1 and fan 2 connectors Ø Power supply voltage monitoring to [...]

Hardware Installation SY-7IS2 15 Chapter 2 HARDWARE INSTALL ATION Congratulations on your purchase of SY-7IS2 Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti- static packaging until you have made the following preparations. 2-1 PRE PARATIONS Gather and prepare all [...]

Hardware Installation SY-7IS2 16 2-2 UN PACKING THE MOTHERBOARD When unpacking the Motherboard, check for the following items: u The SY-7IS2 815EP AGP/PCI/CNR Motherboard u This Quick Start Guide u The Installation CD-ROM u SOYO Bonus Pack CD-ROM u One IDE Device ATA 100 Flat Cable u One Floppy Disk Drive Flat Cable Warning: Do not unpack the Mothe[...]

Hardware Installation SY-7IS2 17 2-3 INS TALLATION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Warning: Turn off the power to the Motherboard, system chassis, and peripheral devices before performing any work on the Motherboard or [...]

Hardware Installation SY-7IS2 18 2-3.1 CPU Installation To perform the installation of your new SY-7IS2 Motherboard, follow the steps below: Mark your CPU Frequency : Record the working frequency of your FC-PGA CPU that should be clearly marked on the CPU cover. FSB 66MHz 400MHz (66 x 6.0) 466MHz (66 x7.0) 533MHz (66 x 8.0) 600MHz (66 x 9.0) 667MHz[...]

Hardware Installation SY-7IS2 19 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without forcing.[...]

Hardware Installation SY-7IS2 20 4. Then close the socket handle to secure the CPU in place. Remember to connect the CPU Cooling Fan to the appropriate power connector on the Motherboard. The fan is a key component that will ensure system stability. The fan prevents overheating, therefore prolonging the life of your CPU.[...]

Hardware Installation SY-7IS2 21 2-3.2 SDR AM Memory Module Installation Your board comes with two DIMM sockets, providing support for up to 512MB of main memory using unbuffered and Non-ECC DIMM modules from 32MB to 512MB, No registered DIMM support. Supports up to 3 Double sided DIMMs at 100MHz system memory. Supports up to 2 double sided or 3 si[...]

Hardware Installation SY-7IS2 22 Memory Configuration Table Number of Memory Modules DIMM 1 DIMM 2 DIMM 3 Single-Side PC100/PC133 PC100/PC133 PC100/PC133 PC100 PC100 P100 PC133 PC133 RAM Type Double-Side PC133 PC133 Memory Module Size (MB) 32/64/128/256/512 MB[...]

Hardware Installation SY-7IS2 23 2-3.3 Motherboard Connector 2-3.3.1 IDE Device Installation (HDD, CD-ROM) This Motherboard offers two IDE device connectors, a primary (IDE1) and a secondary (IDE2). It can support up to four high-speed HDD or CD- ROM. Connect the black connector of the 80-pin flat cable to the IDE device and plug the blue connector[...]

Hardware Installation SY-7IS2 24 2-3.3.2 Floppy Drive Installation The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan. Connect one side of the 34-pin flat cable to the floppy drive and plug the other end t[...]

Hardware Installation SY-7IS2 25 2-3.3.3 Front Panel Connections Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock header. Some systems may feature a KeyLock function with a front panel switch for enabling or disabling the key[...]

Hardware Installation SY-7IS2 26 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard. 4. STR LED The STR LED is c[...]

Hardware Installation SY-7IS2 27 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE (HDD, CD-ROM) device is active. 6. ATX Power On/Off Switch Attach the 2-pin momentary type switch to the PWRBT header for turning On or Off your A TX power suppl y .[...]

Hardware Installation SY-7IS2 28 2-3.3.4 Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices. When connecting a[...]

Hardware Installation SY-7IS2 29 1. Onboard Serial Ports COM1/COM2 External peripherals that use serial transmission scheme include: - serial mouse, - and modem. Plug the serial device cables directly into the COM1/COM2 9-pin male connectors located at the rear panel of the Motherboard. 2. Parallel Port PRT This parallel port is used to connect the[...]

Hardware Installation SY-7IS2 30 5. Universal Serial Bus USB1/USB2/(USB3, USB4) This Motherboard provides four USB ports for your additional devices. Plug the USB device jack into the available USB connector USB1 or USB2. - Standard device drivers come with the Win98 for commonly used USB devices. - With Win95, use the flow UHCI specifications. To [...]

Hardware Installation SY-7IS2 31 2-3.3.5 Other Connections 1. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the W ake- On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card. Please install according to the following pin assignment[...]

Hardware Installation SY-7IS2 32 2. Infrared (IR1) Plug the 5-pin infrared device cable to the IR1 header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications. Please install according to the following pin assignment: Serial Infrared (IR1) Connecto r IR1 Pin Assignment 1 2 3 4 5 VC C IRR X[...]

Hardware Installation SY-7IS2 33 3. Cooling Fan Installation (1) CPU Cooling Fan After you have seated the CPU properly on the processor, attach the 3-pin fan cable to the CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode. (Suspend mode can be enabled from the BIOS Setup Utilit y , [Soyo Combo] menu.) T[...]

Hardware Installation SY-7IS2 34 (2) Chassis Cooling Fan Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector. Install according to the following pin assignment: Note: CPU cooling fan must be installed to pr[...]

Hardware Installation SY-7IS2 35 4. Smart Card Reader 2-3.3.6 AGP VGA Card This motherboard comes with integrated AGP subsystem therefore, AGP VGA card is not needed. Other Display Cards: Insert other types of VGA cards into the AGP or PCI expansion slots according to card specifications.[...]

Hardware Installation SY-7IS2 36 2-3.3.7 A TX Power Supply Plug the connector from the power directly into the 20-pin male A TX PW connector on the Motherboard, as shown in the following figure. Warning: Follow these precautions to preserve your Motherboard from any remnant currents when connecting to A TX power supply: Turn off the power supply an[...]

Hardware Installation SY-7IS2 37 3.3 V -12 V GN D PS-O N GN D GN D GN D -5 V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW-O K 5VS B 12V ATX Powe r Please install the A TX power according to the following pin assignment: Ø Pay special care to the directionality. 2-3.3.8 CNR (Communication Networking Riser)Connector This motherboard supports CNR (Communi[...]

Hardware Installation SY-7IS2 38 2-3.4 Jumper Setting Step 1. CPU Voltage Adjust (VJ2) CPU Voltage Adjust VJ2 Setting Normal Short pin 1-2 +2.5% Short pin 2-3 +5% Short pin 4-5 +7.5% Short pin 5-6 Note: Increasing voltage maybe DAMAGE CPU! SOYO suggest that CPU voltage setting in normal mode. Step 2. Enable/Disable Power-On by Keyboard (JP1) You ma[...]

Hardware Installation SY-7IS2 39 Step 3. Enable/Disable USB Keyboard Wake Up(JP34) You may choose to enable the USB Keyboard W ake Up function by shorting pin 2-3 on jumper JP34; or short pin 1-2 to disable this function. USB Keyboard Wake Up Enable Disable JP34 Setting Short pin 2-3 to enable the USB Keyboard Wake Up function. Short pin 1-2 and th[...]

Hardware Installation SY-7IS2 40 Step 6. CPU Frequency Settings: JP6, JP7, CJ1 and CJ2 For certain Intel CPUs, the multiplier is not locked such that setting a multiplier higher than specified on the CPU is possible. For technical details read the following: Your FC-PGA 133/100/66 MHz FSB CPU has a pin JP6, JP7 to tell it what FSB frequency the CPU[...]

Hardware Installation SY-7IS2 41 2-3.5 Voice Doctor If the system does not boot-up properly, the V oice Doctor will inform the user by voice through internal/external speaker at what point in boot-up sequence the problem arises. Below are the possible errors the user may encounter: 1. The Processor might be damage or not installed properly 2. The m[...]

Hardware Installation SY-7IS2 42 2-3.7 Power On You have now completed the hardware installation of your Motherboard successfull y . 1. Turn the power on 2. To enter the BIOS Setup Utilit y , press the <DEL> key while the system is performing the diagnostic checks, Note: If you have failed to enter the BIOS, wait until the boot up sequence is[...]

Hardware Installation SY-7IS2 43 2-3.8 Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The [SOYO COMBO SETUP] combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS. After the[...]

Hardware Installation SY-7IS2 44 Step 1. Select [STANDARD CMOS SETUP] Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “ Auto ” . Step 2. Select [LOAD SETUP DEFAULT] Select the “ LOAD SETUP DEFAU L T ” menu and type “ Y ” at the prompt to load the BIOS optimal setup. Step 3. Select [SAVE & EXIT SETUP] Press <[...]

Hardware Installation SY-7IS2 45 2-3.9 Troubleshooting at First Start Video (no display) related issues I built a new computer system using a Soyo board and nothing happens when turning it on, no video and no beeps from the PC speaker. What is happening and how can it be fixed? No screen and no beeps mean that your CPU and motherboard do not work a[...]

Hardware Installation SY-7IS2 46 My PCI VGA card works fine with my system, but when I put in a new AGP card, it does not give me any video. Is my AGP slot bad? This is a common problem with AGP video cards. The reason is that your AGP card did not get seated into the AGP slot fully and firmly. Please push your AGP card down into the socket real ha[...]

Hardware Installation SY-7IS2 47 not get my modem to work What you need to do is to disable 'COM2' (or UART2 or serial port 2) in the bios under integrated peripheral setup. I have installed my modem drivers several times and I still cannot get my modem to work. Why? If you are sure that the modem driver has been installed correctly, then[...]

Hardware Installation SY-7IS2 48 The sound and everything else works fine except that the recorder and microphone do not work. What is wrong? This is because the recorder and microphone in the Windows are not enabled. Please go to sound properties and enable them. Lock up (freeze) When I boot up my system, everything works fine. It sees my CPU and [...]

Hardware Installation SY-7IS2 49 Note on Over-clocking Capability The SY-7IS2 provides over-clocking capabilit y . Due to the over- clocking setting your system may fail to boot up or hang during run time. Please perform the following steps to recover your system from the abnormal situation : 1. Turn off system power (If you use an A TX power suppl[...]

BIOS Setup Utility SY-7IS2 50 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utilit y . CMOS Setup Ut[...]

BIOS Setup Utility SY-7IS2 51 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utilit y . Function Command Description F1 General Help Gives the list of options available for each item. F5 Previous V alues Restore the old values. These are the values that the user started the current session with. F6 Load Fail- Saf[...]

BIOS Setup Utility SY-7IS2 52 SAVE AND EXIT SETUP Select the [S AVE & EXIT SETUP] option from the Main Menu to save data to CMOS and exit the setup utilit y . This option saves all your changes and causes the system to reboot. Type [Y] to save the changes and exit or [N] to return to the Main Menu and keep current values. EXIT WITHOUT S AVING S[...]

BIOS Setup Utility SY-7IS2 53 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. After the hardware installation is complete, turn the power switch on, then press the <DEL> key during the system diagnostic checks [...]

BIOS Setup Utility SY-7IS2 54 3-1.1 Quick CPU Frequency Setup Quick CPU Frequency Setup Setting Description Default 110/37MHz/NO 66/33MHz/NO 115/38MHz/NO 68/35MHz/NO 133/33MHz/Yes 70/35MHz/NO 137/34MHz/Yes 75/38MHz/NO 140/35MHz/Yes 80/40MHz/NO 145/36MHz/Yes 83/42MHz/NO 150/37MHz/Yes 100/33MHz/NO 160/38MHz/Yes 103/34MHz/NO 166/42MHz /Yes CPU Host/ P[...]

BIOS Setup Utility SY-7IS2 55 Frequency/ Voltage Control (Continued) Setting Description Note Disabled Default Spread Spectrum Enabled This item allows you to enable/disable the spread spectrum modulate . t. 3-1.4 C.I.H. 4-W AY Protection Settings Setting Description Note Disabled C.I.H. 4- WA Y Protection Enabled When set to enabled, the BIOS can [...]

BIOS Setup Utility SY-7IS2 56 System Memory Control Setting (Continued) System Memory Control Setting Setting Description Note SDRAM RAS- to-CAS Delay 3 2 Use the default setting Default SDRAM RAS Precharge Time 3 2 If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete[...]

BIOS Setup Utility SY-7IS2 57 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] ke y . CMOS Setup Utility – Copyright ( C ) 1984- 2000 Award Software Standard CMOS Features Date (mm:dd:yy) Sat, Jan 1 2000 Time (hh:mm:ss) 2 : 8 : 54 Item Help 4 IDE Primary Master [None] 4 IDE Primary Slave [None] [...]

BIOS Setup Utility SY-7IS2 58 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note IDE HDD Auto- Detection Press Enter To auto-detect the HDD ’ s size, hea d … on this channel Auto BIOS detects hard disk type automaticall y .[...]

BIOS Setup Utility SY-7IS2 59 3-2.4 Others Optional Setting Description Note EGA/VGA Default CGA 40 CGA 80 Video MONO (Monochrome) Select the video mode. ALL Errors Default No Errors All, But Keyboard All, But Diskette Halt On All, But Disk/Key When the BIOS detects system errors, this function will stop the system. Select which type of error will [...]

BIOS Setup Utility SY-7IS2 60 3-3 AD VANCED BIOS FEATURES Select the [Advanced BIOS Features] option from the Main Menu and press [Enter] ke y . CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software Advanced BIOS Features Virus Warning [Disabled] CPU Internal Cache [Enabled] Item Help External Cache [Enabled] Swap Floppy Drive [Disabled] [...]

BIOS Setup Utility SY-7IS2 61 3-3.1 Virus Warning Setting Description Note Disabled Default Virus Warning Enabled Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. 3-3.2 Cach[...]

BIOS Setup Utility SY-7IS2 62 3-3.5 Boot Up NumLock Status Setting Description Note On Puts numeric keypad in NumLock mode at boot-up. Default Boot Up NumLock Status Off Puts numeric keypad in arrow key mode at boot-up. 3-3.6 Gate A20 Options Setting Description Note Normal Lets chipset control GateA20. Gate A20 Options Fast A pin in the keyboard c[...]

BIOS Setup Utility SY-7IS2 63 3-3.8 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. The following table describes the security settings. Setting Description System Each time the system is booted, the password prompt appears. Security Option Setup If a password is set, the password prompt only appears wh[...]

BIOS Setup Utility SY-7IS2 64 3-4 AD VANCED CHIPSET FEATURES Caution: Change these settings only if you are already familiar with the Chipset. The [Advanced Chipset Features] option changes the values of the chipset registers. These registers control the system options in the computer. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software[...]

BIOS Setup Utility SY-7IS2 65 CHIPSET FEATURES SETUP CHIPSET FEATURES Setting Description Note Disabled Default System BIOS Cacheable Enabled The ROM area F0000H-FFFFFH is cacheable. Disabled Default Video BIOS Cacheable Enabled The video BIOS C0000H-C7FFFH is cacheable. Disabled Default Memory Hole At 15M- 16M Enabled Some interface cards will map[...]

BIOS Setup Utility SY-7IS2 66 3-5 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGR A TED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer. The following screen shows setup default settings. CMOS Setup Utilit[...]

BIOS Setup Utility SY-7IS2 67 The following tables describe each field in the INTEGR A TED PERIPHERALS Menu and provide instructions on how to configure the IDE controls, FDC controls, and the onboard serial and parallel ports. 3-5.1 IDE Device Controls IDE Controls Setting Description Note Disabled Turn off the on-board IDE On-Chip PCI IDE Ø Prim[...]

BIOS Setup Utility SY-7IS2 68 3-5.3 IDE HDD Block Mode Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer. Not all HDDs support this function. Default 3-5.4 Others Optional Setting Description Note Password Enables you to wake-up the system by entering a password at the keyb[...]

BIOS Setup Utility SY-7IS2 69 3-5.6 Onboard Serial Ports Onboard Serial Ports Setting Description Note Disabled 3F8/IRQ4 Default (port 1) 2F8/IRQ3 Default (port 2) 3E8/IRQ4 2E8/IRQ3 Onboard Serial Port 1 / Serial Port 2 Auto Choose serial port 1 & 2's I/O address. Do not set port 1 & 2 to the same address except for Disabled or Auto. N[...]

BIOS Setup Utility SY-7IS2 70 3-5.8 Others Optional Setting Description Note On The system will switch on when power comes back after a power failure. Off The system will remain off when power comes back after a power failure. Default PWRON After PWR-Fail Former-Sts The system will return to the state it was in before the power failure when power r[...]

BIOS Setup Utility SY-7IS2 71 3-6 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software Power Management Setup ACPI Suspend Type [S1(POS)] 5 Power Management [User Define] Item Help Video Off Method [DPMS] Video Off In Suspend [Yes] Suspend [...]

BIOS Setup Utility SY-7IS2 72 3-6.1 Power Management Controls Power Management Controls Setting Description Note S1(POS) Default ACPI Suspend Type S3(STR) The system will enter the S1 state during suspend. (Low latency wake up) User Define Lets you define the HDD and system power down times. Default Doze timer Standby timer Suspend timer HDD power [...]

BIOS Setup Utility SY-7IS2 73 Power Management Controls (Continued) Power Management Controls Setting Description Note Disabled Default HDD Power Down 1-15Min When the set time has elapsed, BIOS sends a command to the HDD to power down. This turns off the HDD motor. Some older model HDDs may not support this advanced function. Instant-off Default S[...]

BIOS Setup Utility SY-7IS2 74 3-6.2 Reload Global Timer Events Power Down & Resume Events Setting Description Note Disabled Default IDE0, IDE1 Ø Primary Ø Secondary Enabled In effect, the system remains alert for anything which occurs to a device which is configured as Enabled . Disabled Default FDD, COM, LPT Port Enabled In effect, the syste[...]

BIOS Setup Utility SY-7IS2 75 3-7 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software PnP/PCI Configurations Reset Configuration Data [Disabled] Item Help Resources Controlled By [Auto (ESCD)] x IRQ Resources Press Enter PCI/VGA Palette Snoop [Disabled] Assig[...]

BIOS Setup Utility SY-7IS2 76 3-7.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Disabled Retain PnP configuration data in BIOS. Default Reset Configuration Data Enabled Reset PnP configuration data in BIOS. Manual BIOS does not manage PCI/ISA PnP card IRQ assignment. Requires to assign IRQ-# and DMA-# to PCI or ISA PnP [...]

BIOS Setup Utility SY-7IS2 77 PNP/PCI Configuration Setup (Continued) PNP/PCI Setup Setting Description Note How to set the BIOS to release the IRQ to the PnP Interrupt pool: Interrupt Line PnP / PCI configuration Integrated Peripherals IRQ 15 IRQ 15: PCI / ISA PnP On-Chip Secondary PCI IDE: disabled IRQ 14 IRQ 14: PCI / ISA PnP On-Chip Primary PCI[...]

BIOS Setup Utility SY-7IS2 78 3-8 PC HEA LTH STATUS This option sets the Motherboard's PC Health Status. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software PC Health Status Shutdown Temperature [Disabled] Vcore 1.58 V Item Help VTT 1.45 V 3.3V 3.36 V +12V 11.90 V VB A T (V) 3.07 V CPU Temperature 85°C System Temperature 31°C CPU[...]

BIOS Setup Utility SY-7IS2 79 3-8.1 CPU Device Monitoring CPU Device Monitoring Setting Description Note Disabled Default Shutdown T emperature 60°C/140°F, 65°C/149°F, 70°C/159°F, 75°C/167°F, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F, 100°C/212°F, 110°C/230°F This item allows you to set up the CPU shutdown Temperature. This[...]

BIOS Setup Utility SY-7IS2 80 3-9 LOAD FAIL-SAFE DE FAULTS Select the [Load Fail-Safe Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software 4 Soyo Combo F[...]

BIOS Setup Utility SY-7IS2 81 3-10 LOAD OPTIMIZED DE FAULTS Select the [Load Optimized Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software 4 Soyo Combo [...]

BIOS Setup Utility SY-7IS2 82 3-11 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FE A TURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1. Choose [BIOS FE A TURES SETUP] in th[...]

BIOS Setup Utility SY-7IS2 83 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu. This diagram outlines the password selection procedure: 3-12 USER PASSWORD When the user password option is on, you are not allow[...]

BIOS Setup Utility SY-7IS2 84 Boot Menu Boot Menu enables user to boot-up on different boot device without going into the BIOS setup. T o enable boot Menu, press “ ESC ” after memory initialization, user will see a device menu, in which user can choose on which device they wish to boot from. Boot Men u == Select a Boot First device = = Flopp y [...]

Drivers installation SY-7IS2 85 Chapter 4 THE SOYO CD The SOYO-CD will NOT autorun if you use it on an Operating System other than Windows 9x or NT. Your SY-7IS2 Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains (1) the user's manual file for your new Motherboard, (2) the drivers software available for installat[...]

Drivers installation SY-7IS2 86 The user's manual files included on the SOYO CD are in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system. Note: The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and oth[...]

Drivers installation SY-7IS2 87 Step 2. Install Drivers and Utilities Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own. We recommend that you only install those drivers. (Driver Ins[...]

Drivers installation SY-7IS2 88 Ø ITE SIM card reader of the mobile phone driver for Win 9X/2000/NT If you have reader card, it must be installed. Select which driver you want to install and click OK, or click Cancel to abort the driver installation and return to the main menu. Note: Once you have selected a driver, the system will automatically e[...]

Intel 815 VGA Drivers Installation SY-7IS2 89[...]