Stamina Products 55-1527B manual

When calling for parts or service, please specify the following number : Model#: 55-1527, 55-1527B, 55-1527C W ARNING: T h e B u c k l e S t r a p a n d t h e N y l o n S t r a p m u s t b e attached and properly adjusted at all times during use of this product. This Product is Distributed Exclusively by 2040 N. Alliance, Springeld, MO 65803 Cus[...]

T ABLE OF CONTENTS Safety Instructions ...................................... 2 Before Y ou Begin ........................................ 4 Equipment W arning, Caution & Notice Labels ... 5 Hardware Identication Chart .................... 6 Assembly Instructions ................................ 7 Operational Instructions ...................[...]

3 Call Us Fir st www .staminapr oducts.com 1 (800) 375-7520 Customer Ser vice THANK YOU FOR PURCHASING THE INVERSION T ABLE T o help you get started, we have pre-assembled most of your INVERSION T ABLE at the factory with the exception of those few parts left unassembled for shipping purposes. Simply follow the few assembly instructions set forth i[...]

BEFORE YOU BEGIN 4 Thank you for choosing the INVERSION T A B L E . W e t a k e g r e a t p r i d e i n p r o d u c i n g t h i s quality product and hope it will provide many hours of quality exercise to make you feel better , look better , and enjoy life to its fullest. It's a proven fact that a regular exercise program can improve your phys[...]

This chart is provided to help identify the warning, caution, and notice labels on the INVERSION T ABLE . Please take a moment to familiarize yourself with all of the warning, caution, and notice labels. EQUIPMENT W ARNING, CAUTION & NOTICE LABELS W ARNING LABEL(44) W1 5 Labels are larger than actual size W ARNING DECAL(45) W2 INVERSION W ARNIN[...]

6 Part No. and Description Qty length length mm. in. INCHES This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter . Use the small scale to check the length of the bolts and screws. NOTICE: The length of all bolts and sc[...]

7 ASSEMBL Y INSTRUCTIONS Place all parts from the box in a cleared area and position them on the oor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to[...]

ASSEMBL Y INSTRUCTIONS 8 SLOTS STEP 3 Slide the bottom of the two PIVOT ARMS(5) into the brackets located at each side of the MAIN FRAME(4). Align the desired hole on the arm with the peg on the bracket, and insert the peg into the hole to lock the PIVOT ARMS(5) in position. Then secure the PIVOT ARMS(5) on the pegs with BUTTON HEAD BOL TS (M6x1x8m[...]

ASSEMBL Y INSTRUCTIONS 9 STEP 5 Attach the FOOTREST(8) onto the HEIGHT ADJUSTMENT BEAM(6) with BOL TS(M8x1.25x50mm)(34), W ASHERS(M8)(38), and NYLOCK NUTS(M8x1.25)(36). NOTE: STEP 6 Insert the P AD TUBE(9) through the hole on the HEIGHT ADJUSTMENT BEAM(6) and secure with BOL T(M6x1x45mm)(32) and NYLOCK NUT(M6x1)(35). Place a HEEL HOLDER BRACKET(10)[...]

SET UP INSTRUCTIONS 10 1. 2. A. C. B. BUCKLE 3. STEP 9: Attach the end of the NYLON STRAP(25) to the hook on the back of the MAIN FRAME(4); attach the end of the BUCKLE STRAP(26) to the hook on the FRONT FRAME(1), as shown in Illustration 2. The NYLON STRAP(27) must be secured to the MAIN FRAME(4) and the BUCKLE STRAP(26) must be secured to the FRO[...]

OPERA TIONAL INSTRUCTIONS 1 1 THE HANDLEBARS For added convenience, and safety , a set of HANDLEBARS has been added to the INVERSION T ABLE. These HANDLEBARS are located at the top of the REAR FRAME(2). The HANDLEBARS are to help you return to the upright position from any degree of inversion. If you wish to return to the upright position, and the [...]

OPERA TIONAL INSTRUCTIONS USING THE INVERSION T ABLE 12 1. Check the decline angle before using the INVERSION T ABLE. T o increase the decline, lengthen the straps. T o decrease the decline, shorten the straps. W ARNING: DO NOT ALLOW table to invert past vertical. T able inverting past vertical may result in table contacting frame, damage to table [...]

OPERA TIONAL INSTRUCTIONS 13 Start by lying fully back on the bed with your hands at your side, or resting on your thighs. Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate backward. Stop, or lower your arms to control the downward rotation of the table. Raise your arms until they are over your head.[...]

ST ORAGE 14 FOLDING THE INVERSION T ABLE The INVERSION T ABLE can be easily folded for storage. T o fol d t he INVERSION T ABLE loosen the LOCKING KNOB(17) and pull out the LARGE SPRING PIN(16). Now , slide the HEIGHT ADJUSTMENT BEAM(6) all the way up into the MAIN FRAME(4) until the ADJUST ABLE INSTEP FRAME(7) is just below the MAIN FRAME(4), rele[...]

LIMITED W ARRANTY W ARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and ve years on the frame from the date of the original purchase from an authorized retailer . THIS W ARRANTY SHALL NOT AP PL Y TO[...]

PRODUCT P ARTS DRA WING 16 FRONT BACK[...]

P ARTS LIST 17 P ART# P ART NAME QTY 1 Front Frame 1 2 Rear Frame 1 3 Folding Linkage 2 4 Main Frame 1 5 Pivot Arm 2 6 Height Adjustment Beam 1 7 Adjustable Instep Frame 1 8 Footrest 1 9 Pad T ube 1 10 Heel Holder Bracket 4 1 1 Heel Holder 4 12 Spring 1 13 Small Spring Pin 1 14 Scale Decal 1 15 Bushing 2 16 Large Spring Pin 1 17 Locking Knob 1 18 F[...]

Model Number: ...................................................................................... Serial Number: ............................................................................................. Product Name: ..............................................................................................................................[...]