Star Trac IP-L5002 manual

IP-L5002 BICEPS CURL OWNERS MAN UAL - INST ALLA TION INSTRUCTIONS[...]

Page 2 Copyright 2011. Star Trac by CORE IND USTRIES. All rights reserved, including those to reproduce this book o r parts thereof in any form without first obtaining w ritten permission from Star Trac. Every eff ort has been made t o keep this information curr ent; however, periodical ly, changes are made to the information herein, and these chan[...]

T ABLE OF CONTENTS • SA FETY INSTRUCTIONS / W A RNINGS • W A RNING LA BLES WITH P A RT NUMBERS • EXERCISE GUIDELINES • MA INTEN ANCE A ND SERVICE • W A RRANT Y COVERA GE • INST AL LA TI ON INSTRUCTIONS • HA RDW ARE 4 6 7 8 9 1 1 18 Page 3[...]

Safety Instructions LEVERA GE Safety Info rmation and Genera l Exercise Guid elines Safety Information Read the LEVERAGE Owner's Manual carefu lly b efore assembling, servicing or using the LEVERAGE. ! W ARNING: Serious injury or death could occur if these safety preca utions are not observed: 1. Do not use the LEVERAGE in any way oth er than [...]

13. SECURING EQUIPMENT : All ST AR TRAC equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over . This must be perform ed by a license d contractor . DO NOT use the W eight equipm ent if it is not set up and located on a solid level surface. 14. Make sure that each machine is set up and operated on a solid lev el s[...]

Page 6 731-2991[...]

Exercise Guidelines • Like most exercise, strength training i nvolves an element of risk. Utilize this informa tion to assist y ou and /or your members in making the experience on ST AR TRAC equipment both productive and safe. • Prior to engaging in an y strength-training program, individuals with known health conditions and/or individuals whom[...]

MAINTENANCE AND SER VICE LEVERAGE requires very little upkeep to keep y our equipme nt performing at its best, the following guidelines are suggested. GENERA L CLEA NING  W ipe LEV ERAGE w ith a light all-purpose cleaner , such as diluted Simple Green at a 30:1 solution.  Dry LEVERAGE w ith a sof t cloth to prevent rust. BEA RING GREA SE P A [...]

Warranty Cov erage Star Trac commercial exercise equipment (.Product.) is w arranted to be free of all defects in material and workmanship. Star Trac w arrants all str uctural f rameworks f or a period of 10 years. This limited warranty on structural f rame does n ot incl ude coatings. The follow ing moving parts are w ar ranted for 5 ye ars; rotar[...]

Exclusive w arr antie s THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF A NY KIND EITHER EXPRESSED OR IM PLIED, INCLU DING BUT NOT L IMITED TO THE IMP LIED W ARRANTIES O F MER CHANTABILITY AND FITNESS FOR A PA RTICULAR PURPOSE, AND ALL OTHER OBLIGATIONS OR LIABILITIES ON O UR PA RT. W e neither assume nor authoriz e any person to assure[...]

INST ALLA TION INSTRUCTIONS 1 1 • 5mm Hex Key Soc ket…………………………………... • 6mm Hex Key Socket…………………………………… 1 1 1 • 13mm Box / Open-En d W rench ………………..... • 13mm Socket…………………………………………… • Torque W rench…………………………………[...]

STEP # 1 - UNPA CK A ND A SSEM BLE M AIN FRA M E: 1. Remove and unwrap all product from shipping b oxes. Lay all parts out in a clean open area to prepare for assembly . 2. Locate the MAIN F RAME, SIDE FRAME LEFT and SIDE FRAME RIGHT as shown below . 3. As shown slide SIDE FRAME LEFT into MAIN FRAME. At each tube loosely Install three (M8 X 25MM, B[...]

STEP # 2 - A SSE MBL E LEVE RA GE A RM S: 1.Locate one of th e LEVE RAGE ARMS, slide it onto the corresponding shaft as show below , the side of the le verage arms that has b earing and seal pre-installed will s lide onto the corresponding shaft first. 2.After the one of LEVERAGE ARMS has been sli d onto the corresponding shaft, install a full grea[...]

STEP # 3 – A SS EMB LE CAM ASSEMBLY A ND LEVERAGE C URL A RM S : 1. Sl ide one of the CAM ASSEMBLY S onto the mount of the M ain Fram e as show n, the side of CAM ASSE MBLY that has shaft slide onto the mount first. 2. After the CAM ASSEMB LY has been slid onto the mount, slide one of the LEVERA GE CURL ARMS onto the corresponding shaft of the CA[...]

STEP # 4: INSTA L L BELT 1. Install the BELT PIVOT MOUNT onto the LEV ERAGE ARM, using one (M16x45MM SHOULD BOLT) , tw o (M16 FLAT W ASHER), and one (M12 NYLOCK NUT ) as shown below . 2. Located the BELT end through the BELT HOUSING. Make the BEL T END through under the B ELT PIVOT MOUNT, and bend it up i nto the BELT HOUSING, Then slide B ELT CLAM[...]

STEP # 5: INSTA LL SEA T ASSEMB LY 1. Install SEAT ASSEMBLY and A SSEMBLY FROM ST EP #4 , using four (M8x16MM SOCKET HEAD BOLTS), four (M8 FLAT W ASHER) as shown below. Tighten the b olts at this time. Page 16 STEP# 5:Completed[...]

STEP # 6 – INSTA LL WEIG HT STORA GE, BEARING END CA PS: 1.Install the W EIGH T HORN weldment and BACKING PLATE using tw o (M8 X 75MM, SOCKET HEAD BOLTS) four (M8,FLAT W ASHERS) and two (M8, NYLOCK NUT S). Tighten to specified torque using a 6M M hex key and 13MM wrench. 2. Sli de the COVER and PLASTIC SLEEV E onto W EIGHT HORN weldment. Install [...]

HARDW ARE Page 18[...]

FINAL ASSEMBLE CHECK SHEET 1. Make sure ALL f asteners are tightene d to specifications is this manual. 2. See Mai ntenance and Service page. 1. Perform all steps Page 19 Before using this product, i t is essential to read the EN TIRE operations manual and ALL installation Instructions. T he Ow ner s manual describes e quipment setup and instructs [...]

Part No. 620-8082, Rev A.,M ARCH 2011 STAR TRAC 14410 My ford Road Irvine, Cali fornia 92606 Telephone: (800) 22 8-6635, (714) 669-1660 Fax: (714) 508-3303 ww w.startrac.com[...]