TANDBERG 770 MXP manual

User Manual Software version F5 D13356.07 June 2006 This document is not to be reproduced in whole or in part without permission in writing from:[...]

TANDBERG 770/880/990 MXP ii Trademarks and Copyright All rights reserved. This document conta ins inform ation that is prop rietar y to TANDBERG. No part of this publication may be reproduced, st ored in a re trieval system, or transmitted, in any form, or by any means, electronically, mechani cally, by photocopying, or otherwise, without the prior[...]

User Manual iii eCos eCos, the Embedded Configurable Operating S ystem. Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Red Hat, Inc. Copyright (C) 2002, 2003 John Dallaway Copyright (C) 2002, 2003 Nick Garnett Copyright (C) 2002, 2003 Jonathan Larmou r Copyright (C) 2002, 2003 Andrew Lunn Cop yright (C) 2002, 2003 Gary Thomas Copyright (C) 2002, [...]

TANDBERG 770/880/990 MXP iv Disclaimer The information in this document is furnished for informational purp ose s only, is subject to change without prior notice , and should not be construed as a commitment by TANDBERG. The information in this document is believed to be accurate and reliable; however TANDBERG assumes no responsibility or liability[...]

User Manual v Environmental Issues Thank you for buying a product which contributes to a reduction in p ollution, and t hereby helps save the environment. Our products red uce the n eed for travel and transport and thereby re du ce pollution. Our products have either none or few con sumable parts (chemicals, toner, ga s, paper). Our products are lo[...]

TANDBERG 770/880/990 MXP vi Information for Recyclers As part of compliance with the European WEEE Directive, TANDBERG provides recycling information on request for all types of new eq ui pmen t put on the market in Euro pe after August 13th 2005. Please contact TANDBERG at recy cling@tandberg.net and provid e the followin g details for the product[...]

User Manual vii Operator Safety Summary Operator Safety Summary For your protection please read these safety instructions completely before you con ne ct the equipment to the power source. Carefully observe a ll warnings, precautions a nd instructions both on the apparatus and in thes e operating instructions. Keep this manual for future reference.[...]

TANDBERG 770/880/990 MXP viii  Route the power cord so as to avoid it bei ng walked on or pinched by items placed upo n or against it. Pay particular attention to the plugs, receptacles an d the point where the cord exits from the apparatus.  Do not tug the power cord  If the provided plug does not fit into your outlet, consult an electric[...]

User Manual ix Contact us If you have any questions, comments or suggestions, please se e the Online Support sectio n at www.tandberg.net . It is also possible to send a fa x or mail to the attention of: Product and Sales Support TANDBERG P.O. Box 92 1325 Lysaker Norway Tel: +47 67 125 125 Fax: +47 67 125 234[...]

TANDBERG 770/880/990 MXP x Table of Contents 1 Introduction ................................................................................................................... ............ 1 1.1 At a Glance ................................................................................................................ ............ 5 1.2 Menu St ruc[...]

User Manual xi 3.11.5 Dual Stream (DuoVideo TF / H.239) ............................................................................ 78 3.11.6 Take New Snapshot................................................................................................. 79 3.11.7 Display S napshot ................................................................[...]

TANDBERG 770/880/990 MXP xii 5.3.7 PIP Placing ............................................................................................................ 151 5.3.8 Presentati on Rate .................................................................................................. 152 5.3.9 VNC Setti ngs ..........................................[...]

User Manual xiii Appendix 1: Technica l Specifications ...................................................................................... 246 Appendix 2: Bandwidth Informat ion for TANDBER G Endpoi nts.............................................. 250 Appendix 3: Environmen tal Consid erations ...................................................[...]

[...]

1 1 Introduction The TANDBERG 770/880/990 MXP incorpo rate s the f eatures and function s of larger systems in a portable high performance set top unit. This cr eates a collaborative meeting environment for medium to small-sized meeting rooms. Users can dial in from a video sy stem outside th e enterprise without being registered to a gatekeeper Th[...]

TANDBERG 770/880/990 MXP 2 The system can be configured to act automatic or to give the user a choice of what to do every time the user presses a number key on the rem ote control, when in a call. Audio Quality High-performance audio provides a ri cher, more co mplete visual communication experie nce. The MPEG4 AAC-LD standard is used to provide tr[...]

Introduction 3 MultiSite* The embedded MultiSite TF functionality can cate r for u p to 4 video sites and 3 audio sites and supports screen layouts su ch as VoiceSwitched, AutoSplit, 4 Split and 5+1 Split. The optional embedded MultiSite functionality supports any co mbination of ISDN and IP participants in a conference (up to the total). Superior [...]

TANDBERG 770/880/990 MXP 4 Interoperability The TANDBERG 770/880/990 MXP is world wide compatible with other ITU standard s-based videoconferencing systems from ma ny other vendors world wid e. * - optional feature. To check which options are installed, select Control Panel - Diagnostics - System Information in the menu. TF - TANDBERG First[...]

Introduction 5 1.1 At a Glance Camera The built-in camera includes a high qua lity color camera with a fast pan/tilt/zoom/focus action. The camera is controlled by the system’ s infra-red remote cont rol and operates pan/tilt, focus and zoom. Codec The codec is the heart of the system . Its main task i s the compression of outgoi ng video, aud io[...]

TANDBERG 770/880/990 MXP 6 Microphone The high quality table microphone is de sign ed to be placed on a t able during a video meeting. Up to two microphones can be connecte d. The ideal locati on for the microphone is on a flat surface at least 2m (6.5 ft) from the front of the system. The microphone ca ble sh ould always point towards the system. [...]

Introduction 7 1.2 Menu Structure The Menu is available for all users a nd contains all the functionality of the system. The Cont rol Panel contains all the settings of the system. Makin g chang es to the settings will change the behavior of the system. The m enu structure is shown below.[...]

TANDBERG 770/880/990 MXP 8 Note that the system features and menu se ttings may vary dependi ng on network selection and software package.[...]

9 2 Inst allation Precautions:  Never install communicati on wiring during a lightnin g storm.  Never install jac ks f o r communication c able s in wet locatio n s u nless the jack is specifically designed for wet locations.  Never touch uninstalled communi cation wires or terminals u nless the telephone line ha s been disconnected at the[...]

TANDBERG 770/880/990 MXP 10 2.1 Unpacking and Mounting The TANDBERG 770/ 880/990 MXP con sist s of the following items:  Videoconferencing system with built-in camera  Table Microphone  Remote Control  Batteries  User Manual on CD  Cables Place the system centrally, on top of the monitor, close to the front and ensu re it is stabl[...]

Installation 11 2.2 Connecting Cables[...]

TANDBERG 770/880/990 MXP 12 1. Microphone cable  Connect the microphone to the microphone cable.  Connect the microphone cable to microphone input 1 on the syste m. 2. Monitor cable(s) To get the best possible picture quality, conne ct the DVI output of the TANDBERG system to a flat screen with DVI/VGA input. With Scart (Europe):  Connect [...]

Installation 13 4. Power cable  Connect the power cable from the system’s powe r connector to an electri cal di stribution socket. 5a. LAN cable  To use the system on LAN, conn ect a LA N cable from the ‘Ethernet’ connector on the system to the LAN. 5b. Wireless LAN - Insert PC Card  Remove the “dummy” card by pressing the ‘Eje[...]

TANDBERG 770/880/990 MXP 14 2.3 Monitor Configuration Power on Power on the monitor and use the monitor rem ote control to select the Audio/Video inp ut used (refer to the monitor manual). If using S-video from the system, re membe r to select S-Video input to avoid a black and white picture. Select Audio/Video input on monitor Selection of Audio/V[...]

Installation 15 2.4 System Configuration The system must be configure d for each insta llation. Configuration settings can be made via the system menu. Navigate through the menu system using the arro w ke ys and OK. Remember to press the Save button on the bottom of each menu to save the c hanges. Pre ss Cancel (x) to ret urn to the previous Menu. [...]

TANDBERG 770/880/990 MXP 16 5. Screen Settings When using wide scree n (16:9) mo nitors, set TV Monitor Format to Wide (16:9). TANDBERG also recommends setting Picture Layout to Picture outside Picture when using 16:9 monitors. Picture outside Pictur e provides a displ ay layout optimized for wide screen monitors. The display layout may be cha nged[...]

Installation 17 5. Data Port Please refer to Data Port for details 6. Save changes Remember to save any changes made in the menu b y selecting the Save button on the Menu line and pressing OK. * The International Name field is only vi sible if the system name contains Asian and non -Latin character text input.[...]

18 3 General Use Wake up the sy stem When the system is not in use, it is in standby mode and the screen(s) are black. Wake up the system by picking up the remote control. An incomi ng call or pressi ng any key o n the remote control will also wake up the system. If the system does not respond:  Make sure that t he system is switche d on by usin[...]

General Use 19 3.1 The Welcome Screen When the system is switched on, the welcome scre en will be displayed. The welcome screen presents the menu and displays your main cam era image in the background (display main camera is the default setting). The ISDN/IP num bers and the system name are displ ayed in the upper right corner. The ISDN Numbe r and[...]

TANDBERG 770/880/990 MXP 20 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arro w keys a nd press OK to navigate through the menus. The system’s most commonly used functions are al so accessible directly from the rem ote control. Th[...]

General Use 21 11. Use Zoom + and – to zoom the camera in and out.* 12. Selfview displays your outgoing video. Press Selfview again to turn selfview off, see Selfview . 13. Use the Phone Book to store and recall video contacts for easy placement of calls, see Phone Book . 14. Use the red End Call key to end the current call. Pressing this key whe[...]

TANDBERG 770/880/990 MXP 22 The remote control (TRC 4)**: 1. Change video source. If possible, you will start open a Dual Stream. Press the video source button again to stop the dual stream. 2. Mic Off turns your microphone on and off, see Mic off . 3. Arrow keys are used for navigation in the menu and for moving the camera* when the menu is hidden[...]

General Use 23 presentation source. If the Presentation key is held down for 1 second then the Presentation video sources menu will appear, see Presentation Key . 12. Press OK/Menu to show the menu and to select menu items, see Navigation . 13. Use Zoom + and – to zoom the camera in and out.* 14. Selfview displays your outgoing video. Press Selfv[...]

TANDBERG 770/880/990 MXP 24 3.2.1 Navigation Arrow keys and OK Navigate in the menu with the arrow key s on the remo te control. The orange selector on screen show s the selected item. Press OK to select. Cancel key In the Menu, pressing Cancel (X) w ill hide the menu. If the menu is hidden, bring it back with OK. In other menu s, pressing Ca ncel [...]

General Use 25 3.2.2 Selfview The term “Selfview” means the outgoing image. In a normal call using the main camera, this is the image of yourself. The Selfview button toggles the images betwee n Far En d, Selfview and Dual Video (if any). How to use Selfview : 1. Outside a call, pressing the Selfview button will switch between the near end vide[...]

TANDBERG 770/880/990 MXP 26 Example: You are using the system as a PC and get an incom ing call. When the setting “Use Screen as Local PC monitor” i s On, you will keep your PC image displayed locally and the incoming call pops up in a PIP or as sm aller images in a 1+3 layout, depending on your system. You will see Local PC displayed in the bi[...]

General Use 27 3.2.3 Picture Layout The layout of the screen can either be shown a s Pi cture in Picture (PIP) or Picture outsid e Picture (POP) when displaying more than one video imag e. The beh avior of the Layout button is dependent on the Picture Layout setting in Scre en Settings . 3.2.3.1 Picture in Picture When Picture Layout is set to PIP,[...]

TANDBERG 770/880/990 MXP 28 3.2.4 Mic Off To mute the microphone during a call, press the Mic off button. An on-scree n in dicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash. Pressing the Mic o ff button one more time will activate the microphone again. Not[...]

General Use 29 3.2.5 Volume + and - Press the Volume key to adjust the volume leve l of the codec only (not the monitor). An on- screen indicator will sh ow the current level.[...]

TANDBERG 770/880/990 MXP 30 3.2.6 Number and Letter keys Pressing a number key when outsi de a call will bring up the call menu. Wh en in a call, the number keys are used for Camera Presets. Press a n umber and go to the corresponding Camera Preset (see Camera Presets ). However, when accessing an input field where numbers are required, the system [...]

General Use 31 3.2.7 Touch Tones To activate dialing touch tones during a call, press the Touch tone s butt on. Oth erwise the number keys will work as configured in the Num ber Key Mode, see Control Panel – Menu Settings – Number Key Mode. An indicator will let you know that Touch tones are en abl ed. Press OK to exit Touch tone mode.[...]

TANDBERG 770/880/990 MXP 32 3.2.8 Presets and Extension Numbers When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen. The system can b e configured to act automatic or ma nual. While in a call, the user presses a numb er key to: • add another call • dial extension numbers • use camera prese[...]

General Use 33 3.3 On-screen Indicators The system has a number of icons signaling diffe rent settings: Microphone Off This indicator is shown when the microphone is turned off. Press the Mic off button again to turn the microphone back on, see Mic Off for details. Volume Off This indicator is shown when the volume is turned off. Press Volume + to [...]

TANDBERG 770/880/990 MXP 34 Telephone This indicates that there is a telephone p articipant in the conference. The displayed number indicate s ho w many telephone participa nts there are in the conference. Duo Video / H.239 This indicates that there is a Dual Vide o Stream sent from you (near end ). The feature Duo Video / H239 allows partici pants[...]

General Use 35 3.4 Using the Menu Menu outside a call Menu when in a call. Press the Menu button on the remote co ntrol to displ ay the menu. The menu contains all functions needed in order to control the system.[...]

TANDBERG 770/880/990 MXP 36 The menu contains the following items:  Make a Call / Add Another Call  Standby / End Call  Camera Control  Presentation  Conference Service s  Control Panel  Close See Menu Structure for a full overview of the menu. The functions of the menu are displayed as icons. The curre ntly se lected icon is m[...]

General Use 37 3.5 Make a Call It is easy to make a call: 1. Press the green Call button on remote control and Di al Number. 2. Press the green Call button again to initiate the call. Display the Call menu by either: 1. Select Make a Call from the menu, or 2. Press the green Call button on the remote cont rol The TANDBERG system can make both Video[...]

TANDBERG 770/880/990 MXP 38 3.5.1 Place a Call The TANDBERG system can make both Video calls and Telephone calls . A Call Type selector button is placed to the right of the number entry field. The button sho ws if it is a video call (default) or a telephone call . Press the b utton to show a drop down list to select the type of cal l. Display the C[...]

General Use 39 Place the call by either: 1. Use the arrow button on the remote co ntrol to select the Place Call icon an d press OK, or 2. Press the green call button on the remot e control. TIP: When dialing a telephone numbe r and pressing the green Call button on the remote cont rol, the system will in most cases autom atically interpret the num[...]

TANDBERG 770/880/990 MXP 40 3.5.2 Add Call (Optional feature) Conference systems with b uilt-in MultiSite can handle up to 4 video calls and 3 tel epho ne calls simultaneously. It is possible to both set up a conference with many participants and also ad d participants durin g a conference. Set up a conference w ith t wo or more participants Displa[...]

General Use 41 3.5.3 Call Settings The Call Settings specifies the quality of the ca ll. Each call will be set up with the default Call Settings if the settings are not altered. Usually it is not necessary for the user to alter the settings. The Call Settings are defined in Control Panel - Call Quality - Defa ult Call Settings. When setting up a ca[...]

TANDBERG 770/880/990 MXP 42 3.5.4 SIP Services SIP enables you to use the features Add Call and Transfer even if your system doe sn’t have multipoint capabilities. To get t he SIP Services available, you hav e to make a call using SIP as your Net. (See Call Settings) 3.5.4.1 Add Call You can add another call to your existin g SIP call. How to Add[...]

General Use 43 3.5.5 Streaming Streaming lets you broadcast your meeting to particip ants on the web. The web participant s can listen to the meeting, see snapshots, but not parti cipate themselves. Snapshot s of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http. See Appendix 6 for descriptions of the pos[...]

TANDBERG 770/880/990 MXP 44 Source* Selection of which site to be streame d is done using voice switching (the site that spe aks is st reamed).  Local: Only the local video will be streamed.  Remote: Onl y the far end video will be streamed. Local and far end audio is alway s stre amed. Allow Remote Start  On: Streaming can be started from[...]

General Use 45 3.5.6 Dialing In From Outside the Enterprise Dialing in Without Being Registered to a TANDBE RG Gatekeeper The feature enhancement enables diali ng th rough a TANDBERG Gatekeepe r without being registered to it. This makes it easy to call in from a video system outside the enterprise. It's done by dialing: EndPointAlia s@Gatekee[...]

TANDBERG 770/880/990 MXP 46 3.6 Answer an incoming call How to answer an incoming call:  To accept an incoming call, press the OK button or the green Call b utton on the remote control. How to reject an incoming call:  To reject an incoming call, select the Rej ect icon and pre ss the OK button, or press the End Call button on the remote cont[...]

General Use 47 3.7 End Call How to end a call:  Press the red End Call button on the remote control, or  Press the Menu button on the remote control to displ ay the menu and select End Call. When the End Call dialog box is displayed either:  Press the red End Call button on the remote control again, or  Press the OK button to confirm th[...]

TANDBERG 770/880/990 MXP 48 3.8 Standby The system will automatically go to Standby mode when it is not in use. In standby mode, the screen(s) are black. It is however st ill possible to receive incoming calls. How to enter standby mode manually :  Select Standby from the menu and select Standby Now, or  Press the End Call button on the remot[...]

General Use 49 3.8.1 Delay Standby for 1 hour Delay Standby for 1 hour postpones the system fro m enterin g standby mode for 1 hour. This function is useful when using the monitors for a local presentat ion to preven t the system from automatically blanking the monitors. It is also possible to postpone the system from entering standby mode for 3 ho[...]

TANDBERG 770/880/990 MXP 50 3.8.2 Delay Standby for 3 hours Delay Standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentat ion to preven t the system from automatically blanking the monitors. It is also possible to postpone the system from entering standby mode for 1[...]

General Use 51 3.8.3 Do Not Disturb To prevent the system from accepting any incomi ng calls, activate the Do Not Disturb function. The caller will hear a bu sy tone when calling t he system. The monitor will be black when Do Not Disturb is active, see figure below. This is useful when using the display for a pre sentation as a local PC monitor and[...]

TANDBERG 770/880/990 MXP 52 3.9 Phone Book The Phone Book is available via the Phone Book bu tton on the remote cont rol or from the Make a Call menu. Using the Phone Book is time saving and prevent s the user from inadvertently calling the wrong number. The contacts are sorte d alphabetically . The contact names are displayed in the list and the t[...]

General Use 53 The following information is available from the P hone Bo ok:  Placed Calls  Missed Calls  Received Calls  My Contacts  Global Contacts[...]

TANDBERG 770/880/990 MXP 54 3.9.1 Call Log The Call Log lists Placed Calls, Missed Call s and Re ceived Calls. That allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted. If the contacts listed are availa ble in the phone book, [...]

General Use 55 3.9.2 My Contacts My Contacts are the locally stored contacts on t he system. This means that it is possible to add new contacts and edit or del ete existing contact s. My Contacts can store up to 200 contacts. How to make a call using My Contacts: 1. Find the desired contact using the arro w keys o r searching on the first letter wi[...]

TANDBERG 770/880/990 MXP 56 The following functions are av ailable from My Contacts:  Call Now  New Contact  New MultiSite Contact  Edit Contact  Delete Contact  Close[...]

General Use 57 3.9.2.1 Add New Contact The New Contact function is availabl e from My Conta cts . Add a new contact to My Contacts by: 1. Select the New Contacts button to open the New Contacts dialog b ox. 2. Enter Name by using the letter keys on the remote control. Input will automatically be interpreted as letters. Toggle betwe en ca pital lett[...]

TANDBERG 770/880/990 MXP 58 3.9.2.2 New MultiSite Contact (Optional feature*) The New MultiSite Contact function is av ailable from My Contacts . It is possible to pre-define the participa nts of a conference me eting as a MultiSite Contact. All participants in the MultiSite Contact will then be co nnected automatically instead of having to call th[...]

General Use 59 Bandwidth for a MultiSite Contact call When calling a MultiSite Contact, the system will tr y to call the participants with their specified bandwidths. If the total bandwidth exceeds the sy stem's maximum bandwidth the system will downspeed and distribute the av ailable bandwidth equally among all the partici pants. Example: In [...]

TANDBERG 770/880/990 MXP 60 3.9.2.3 Edit Contact The Edit Contact function is available from My Contacts . How to edit a contact in the Local Phone Book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote contro l, followed by the down arrow until the Edit Contact ic on is selected . 3. The current settings for this c[...]

General Use 61 3.9.2.4 Delete Contact The Delete Contact function is available from My Contacts . How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow u ntil the Delete Contact icon is selected. The Delete Co ntact dialo gue box is displayed. 3. Confirm by pr[...]

TANDBERG 770/880/990 MXP 62 3.9.3 Global Contacts When selecting Phone Bo ok the ph one book ope ns showing the Gl obal Contacts* or the Corporate Directory** below the folders: Plac ed Calls, Missed Calls, Received Calls and My Contacts. These contacts cannot be change d loca lly by the system, only from the management system. If there is a need t[...]

General Use 63 3.9.3.1 Up one Level Global Contacts can be arranged in a tre e stru ct ure with several sub folders. Use the Up one Level button to navigate up in the tree structure. When a search in the Global Phone Book is m ade by using the Search fun ctio n, only conta cts matching the search text are displayed. Select the Up one Level button t[...]

TANDBERG 770/880/990 MXP 64 3.9.3.2 Search The phone book can cont ain an unlimited amount of global contac ts. Usin g search makes it easier to find the wanted contact. How to search in the Global Phone Book: 1. Select the Search icon. 2. Enter search text in the dialogue box that appears and press the OK button on the remote control. The system w[...]

General Use 65 3.9.3.3 Copy Contact to My Contacts The Copy Contact to My Contacts function is available from the Placed Call s, Missed Calls, Received Calls and Gl obal Contacts folders, see Phone Book for details. It may be wise to copy contacts t hat are often used to My Contacts. Note that the local copy will not be updated if the Global Contac[...]

TANDBERG 770/880/990 MXP 66 3.10 Camera Control There are several ways to control the camera:  Control the camera directly with the arrow keys when the menu is closed or use the Move Camera function in the menu to cont rol both the near end and far end camera, see Move Camera and Far End Cont rol for details.  Use the zoom button on the remot[...]

General Use 67 3.10.1 Move Camera It is possible to move the camera with the remote cont rol or via the menu. Moving the camera directly with the remote control When the menu is hidden, the arrow key s will work on the camera. If the menu is displayed, press the Cancel button on the remote control to hide it. Use the left and right arrow keys to pa[...]

TANDBERG 770/880/990 MXP 68 3.10.2 Far End Control Far End Control allows you to control yo ur conference partner’s ca mera. An exa mple of when this feature could be especially helpful is if it is not possible to see wh at a partici pant at the far end is writing on their white board. Use Fa r End Control to move the far end camera and zoom clos[...]

General Use 69 3.10.3 Camera Presets Use camera presets to easily vary between predef ined near end ca mera a ngles. This is useful when pictures from many different camera an gles have to be sent to the far end. E.g. in a meeting there is a white board, a PC and a sma ll meeting table. Use camera preset s to move between these camera p erspe ctive[...]

TANDBERG 770/880/990 MXP 70 3.10.4 TANDBERG Tracker How to save presets for the TANDBE RG Tra cker: 1. Select which camera prese t is to be use d on the TANDBERG Tracker. 2. Move the camera to the desired position to store on the tracke r. 3. Select Move Camera - Save New Preset in the menu. 4. All camera presets are access ible from the TANDBERG T[...]

General Use 71 3.10.5 Picture Control Focus, Brightness and Whi te balance are set for auto focus, auto br ightne ss a nd auto white balance by default. If you need to set focus, bri ghtness and white balance ma nually, go to Picture Control in the Camera Control menu. Focus Auto Auto focus continuously updates the fo cus thro ughout the call. When[...]

TANDBERG 770/880/990 MXP 72 3.10.6 Camera Tracking Through Camera T ra cking and the use of two or three microph ones, the camera can automatically position itself on t he current speaker. Before usi ng camera tracking, the camera positions used must be stored at Pre s et 7 (Mic1) and Preset 8 (Mic2). How to use Camera Tracking: 1. Select the Camer[...]

General Use 73 3.11 Presentation The Presentation Functionality in the system enabl es you to show other available video sources in addition to your Main Camera. This is perfe ct for meetings where you would like to show a PowerPoint presentation, for example. You can even use arro w keys up and down on the remote control to activate Page Up/Down o[...]

TANDBERG 770/880/990 MXP 74 3.11.1 Presentation Key The quickest way to show a pre sentatio n is to use th e presentation key on the remote control. The presentation key is used to start and stop a presentation. The presentation key will display PC (default*). When holding the pre sentat ion key for 1 second, the presentation menu will be displayed[...]

General Use 75 3.11.2 Presentation Menu The Presentation menu offers you all available video sou rces; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used a s Main Video S tream or Dual Video Stream (Duo Video / H.239). Not all sy stem s ha s all video sources available, see Interfaces for details. Outside a call the p[...]

TANDBERG 770/880/990 MXP 76 3.11.3 PC Presenter (DVI/VGA Input) (Optional feature - not available on all system s) Users often have their present ations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec befo re you press the Presentation button. Note that the image will appear smoother on the system if y ou[...]

General Use 77 3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC image s on yo ur system without using a VGA cable (PC Presenter). The system and your PC must be connect ed to the same LAN. In addition, VNC (Virtual Network Computing) server software mu st be installed on the PC. Free softwa re can be downlo[...]

TANDBERG 770/880/990 MXP 78 3.11.5 Dual Stream (DuoVideo TF /H.239) (Optional feature - not available on all system s) With Dual Stream you have the opportunity to show two different live video stre ams simultaneously, main video and one a ddi tional source. This is hand y when showing a presentation. You see the live presentation and the live vide[...]

General Use 79 3.11.6 Take New Snapshot The system can take a snapshot of your live vi deo. Snapshot is han dy when you are in a call with a system that does not support Dual Stream. Use Snapshot to show a snap shot of your presentation and continue the meeting with main camera. How to use snapshot: You find Take New Snapshot in the Presentation me[...]

TANDBERG 770/880/990 MXP 80 3.11.7 Display Snapshot The system stores the last sent or re ceived S napshot. The snapsho t is deleted a utomatically after the call. How to display snapshots: 1. To view a stored snapshot, first choose the Snapshot header. 2. Select Display Snapshot in the Presenta tion menu. 3. Press the Hide Snapshot button again to[...]

General Use 81 3.12 Services A Multipoint Control Unit (MCU) enables severa l sites to participate in the same conferen ce. During an MCU confe ren ce, the status line will provide information about the conference. Services contain the follo wing features: • Request Floor and Release Floor • Conference Layout • Terminal Names • Chair Contro[...]

TANDBERG 770/880/990 MXP 82 Example of MultiSite for mid- to low end systems. Note that the illustrations may differ from the actual product. Using the system’s internal MCU, MultiSite TF * Most TANDBERG MXP systems have an optional b u ilt-in MCU, wh ich is called MultiSite*. It supports up to 6 video calls and 5 tele p hone calls including your[...]

General Use 83 Using an external MCU with limited Chair Control Support y ou may hav e the following services With an external MCU that does not support H.243, you have the following servi ces:  Reques t/Release Floor  Terminal Names * The MultiSIte option is not available on the TA NDBERG 55 0 MXP, TANDBERG 770 MXP and TANDBERG 1000 MXP[...]

TANDBERG 770/880/990 MXP 84 3.12.1 Request Floor and Release Floor When requesting floor, your video will be broad casted in full screen to all other participants in the conference. Request Floo r is u seful when you want to speak or display somethi ng in front of all participants. Release Floor when you are done and m ake the fl oor available for [...]

General Use 85 3.12.2 Conference Layout (Only supported by TANDBERG MultiSite*) With a TANDBERG MultiSite you can choose between the layouts: Auto Split, 4 Split, 5+1 Split and Voice Switched view. Auto Split displays all pa rticipants on the screen simultaneously. 4 Split displays the 4 last spe aking Part icipa nts incl uding the MultiSite host .[...]

TANDBERG 770/880/990 MXP 86 3.12.3 Terminal Names Choose Terminal Names to see a list of the parti ci pants of the MultiSite c onference. Press Cancel to go back.[...]

General Use 87 3.12.4 Chair Control (Not supported by TANDBERG MCU o r MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Co ntrol to assume the role of chairman of the conferen ce. Sele ct Release Chair to end the role as chairman. A Chair indicator appears when you have Ch air and disappea rs when chair is released.[...]

TANDBERG 770/880/990 MXP 88 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to sel ect whi ch of the conference participants are to be broadcasted to all other participants.[...]

General Use 89 3.12.6 View Site and End View (Not supported by TANDBERG MCU o r MultiSite) View Site allows you to view any participant in the conference regardless of wh o has the floo r and chair. Choose End View to go back to norm al.[...]

TANDBERG 770/880/990 MXP 90 3.12.7 Disconnect Participant Disconnect Participant allows the chai rman to di sconnect any participant in the conference. In a multipoint call, this is equivalent to disc onnecting a participant from the end call menu.[...]

General Use 91 3.12.8 Terminate Meeting Terminate Meeting allows the chai rman to terminat e the conference altogethe r. In a MultiSite call, this is equivalent to pressing End All Call s from the end call menu.[...]

TANDBERG 770/880/990 MXP 92 3.12.9 More about MultiSite (embedded MCU) (Optional Feature*) Calling in to a MultiSite Any system can be part of a MultiS ite conference by calling in to a MultiSite. The dial-in numbers to the MultiSite depends of t he network that is used. To dial in to the MultiSite on IP:  Dial the IP Number or the IP Address of[...]

General Use 93 3.12.10 Text Chat While in an ISDN or IP call to another system suppo rting Text Chat (T.140), select Text Chat the Services Menu. Enter text in the displayed window. How to use Text Chat: 1. Choose Text Chat from the Servic es Menu to open the Text Chat window. 2. Enter text with the number keys like on a mobile phone. The text is s[...]

TANDBERG 770/880/990 MXP 94 4 Control Panel The Control Panel contains the features:  User Guide  Diagnostics  Audio Demo  Restart  Settings* Settings:  General  Call Quality  Security  Menu Settings  Audio  Network  Presentation Settings  Video  Restore Default Settings NOTE: If Administrator Password is O[...]

General Use 95 4.1 User Guide The on screen user guide take s you through a quick step-by-step introduction to the video system. It gives the user basic skills in how to use the system.[...]

TANDBERG 770/880/990 MXP 96 4.2 Diagnostics Diagnostics allows testing of individual syste m components a nd displays the current system settings. Diagnostics contain:  System Information  Channel Status  Call Status  System Selftest  View Settings  IP Address Conflict Check  Warnings[...]

General Use 97 4.2.1 System Information Select System Information to view system numbers , line status, soft ware ve rsion, hardware serial number and other useful information. Press arro w key up and down to scroll in the System Information list. System Information con t ains: System Name My ISDN Number My IP Number My IP Address MultiSite number [...]

TANDBERG 770/880/990 MXP 98 4.2.2 Channel Status Comprehensi ve informatio n about the call progre ss is available through the Channel Status window. This window indicates the vario us stages each B-channel goe s through whilst establishing a connectio n. Status - BRI Comments Idle Calling Connected Sync Active Releasing Released the channel is idl[...]

General Use 99 4.2.3 Call Status Comprehensive informatio n about the call is availabl e through the Call Status window. The menu has two columns, one for transmitted an d one fo r received audio/vi deo/data information. If Dual Stream or MultiSite is available on your syst em and in use, pressi ng the UP/DOWN key s will show one page per conne cte[...]

TANDBERG 770/880/990 MXP 100 4.2.4 System Selftest The system performs a che ck to determine internal hardware integrity. System Selftest is useful when you want to check if your network connection is active.[...]

General Use 101 4.2.5 View Settings This window displ ays all th e system settings. Us e the arrow key on the remote control to scroll through the list. View Settings may contain*: General Settings System Name Language Dual Monitor Auto answer Max Call Length Access Co de Incoming MCU calls Incoming Telephone calls Far End Control Fallback to Telep[...]

TANDBERG 770/880/990 MXP 102 Document Camera VCR AUX VNC Split Screen Default Call Settings Call Type Network Bandwidth Restrict (5 6 k) Auto H320 Bandwidth Auto H323 Bandwidth SIP Audio Settings Inputs Mic1 Mic2 Mic3 Audio4 Audio5 Audio6 Mix Mode VCR Ducking Level Settings Mic1 Mic2 Mic3 Audio4 Audio5 Audio6 Outputs Out1 Out2 (AUX) Out3 (VCR) Out1[...]

General Use 103 Brightness Video Name Main Cam AUX Doc Cam VCR PC VGA VNC Network Ty pe ISDN-BRIPRILeased E1T1External H331 ISDN Switch Type ETSI (Euro ISDN) Line1 Setup On Number1 Number2 SPID1 SPID2 Line2 Setup On Number1 Number2 SPID1 SPID2 Line3 Setup On Number1 Number2 SPID1 SPID2 Advanced ISDN Settings Sub Address Validate Numbers (MSN) P[...]

TANDBERG 770/880/990 MXP 104 Gateway Ethernet Speed DNS Settings H.323 Settings E.164 Alias Use Gatekeeper Gatekeeper IP H.323 Prefix Advanced H.323 Settings RSVP NAT NAT Address QoS IP Precedence Audio Video Data Signaling IP Type of Service (TOS) Diffserv Audio Video Data Signaling IEEE802.1x Settings IEEE802.1x Mode Anonymous Identity Identity E[...]

General Use 105 Data Port 1 Baud rate Parity Data bits Stop bits Mode Data Port 2 Baud rate Parity Data bits Stop bits Mode * The settings available will vary within the MXP system r ange depending on system and what software options installed.[...]

TANDBERG 770/880/990 MXP 106 4.2.6 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Che c k.[...]

General Use 107 4.2.7 Warnings Any warnings registered by the system will be displayed in the Warnings me nu. Open a warning in the list to get more information about the warning. The following warnings ma y be displaye d if detected by the system, depending on system type and configuration: ISDN BRI warnings  ISDN is enabled on BRI line x, but [...]

TANDBERG 770/880/990 MXP 108  There is something wrong with the Leased E1/T1 line (Blue alarm). Please che ck your network connection. (1 92)  There is something wrong with the Leased E1/T1 line (Yellow alarm). Please check your network connection. (1 93) H323 gatekeeper warnings  Could not register to the gatekeeper.  The gatekeeper re[...]

General Use 109 4.3 Audio Demo TANDBERG systems are desi gne d to improve audio quality during a video con f eren ce – as if the person is in the same room! Demonstrate the high quali ty Audio of your system by pressing the Audio De mo button at the bottom of the Control Panel menu. Lean back and enjoy![...]

TANDBERG 770/880/990 MXP 110 4.4 Restart Restart the system by pressing the Restart butt on. You are prom p ted with a dialog box saying: Do you want to restart the system? Press OK to restart, press Cancel (X) to abort.[...]

111 5 System Settings The Control Panel contains all the settings of the syst em. Making changes to the settings will change the behavior of the system. It is reco mmended to password protect the access to the settings to prevent occasional users from making cru cial chan ges to the system, see Control Panel – Security – Administrator Password [...]

TANDBERG 770/880/990 MXP 112 5.1 General Settings When installing the system, go through the Gene ral Settings menu to ensure that you have the right settings for your syste m , see Syste m Configuration. General Settings contain:  Language  System Name / International Name *  Auto Answer  Phone Book Settings  External Service Settin[...]

General Use 113 5.1.1 Language The system supports 16 dif f erent lang uages for its on-screen menus; English, G erma n, French, Norwegian, Swedish, Italian, Spanish, P ortuguese, Russian, Finnish, Chinese Simplified, Chinese Traditional, Japanese, Korean, Thai and Arabic. Select the preferred lang uage and press OK to save. Note that pressing the [...]

TANDBERG 770/880/990 MXP 114 5.1.2 System Name System Name identifies the sy stem:  On the welcome page.  During an MCU conferen ce call.  When using the Web-interf ace.  When the codec is acting as an SNMP Agent.  Towards a DHCP serve r.  H323 ID. Other systems can call in usin g this name instea d of IP-number/IP-address. System[...]

General Use 115 5.1.3 International Name If the System Name contains Asian and non-Latin cha racte r text input, the International Name using Latin characters only , must be sp ecified as well. This is in order to make other s ystems understand the system na me.[...]

TANDBERG 770/880/990 MXP 116 5.1.4 Auto Answer The auto answer setting decides whether an incomin g call is p ut through automatically or manually. On The system will automatically answer al l incoming cal ls. On+Mic Off The system will automatically answer all incomin g cal ls and switch the microphone off when the call is connect ed. Press Mic Of[...]

General Use 117 5.1.5 Phone Book Settings Corporate Directory On The Corporate Dire cto ry is available in the menu. Off The Corporate Dire cto ry is hidden from the menu and is unavailable for users. IP address Enter the IP address of the management system that provides the Phone Boo k. Path The Path indicates the function of the manag ement syste[...]

TANDBERG 770/880/990 MXP 118 5.1.6 External Services Settings External Services On When set to On External Services are available. Off When set to Off External Services are unavailable. IP address Enter the IP address of the service provider for Extern al Service s. Path Enter the Path to the External Services provider. The services available are d[...]

General Use 119 5.1.7 Permissions Permissions contains settings for in coming MC U Calls, inco ming telephone Calls, Far End Control, Remote Software Upgrade and Fallba ck to Telephony. Access Code An access code will help you control the use of the system. All users must enter a code to identify themselves and the call will be cha rged on thei r a[...]

TANDBERG 770/880/990 MXP 120 Far End Camera Control On The far end will be able to: • Control your camera • Select your video sources • Activate your camera presets • Request snapshots Off The far end can access none of the four features abo ve on the local system. You will however still be able to control the camera on the fa r end. Fallba[...]

General Use 121 5.1.8 Screen Settings Auto Layout On If Auto Layout is On the system will change layouts automatically depen ding on t he number of participants in a call and if you have a dual video strea m or not. Please refer to Layout for more information. Off If Auto Layout is Off there will be no auto matic layout changes during a call. All d[...]

TANDBERG 770/880/990 MXP 122 Picture (PIP) smaller view (Picture in Picture). Press the Layout button to move it around in the corners of the screen and finally hide it. Pressing and holding Layout for 1 second will hide the small picture directly from any position. Picture outside Picture (POP) Press the Layout button to see the im ages side-by-si[...]

General Use 123 Example of 1+2 Picture outside Picture (wide screen). Example of 1+3 Picture outside Picture (wide screen). Note that if both TV monitor format and VGA fo rmat is set to Normal, the system will skip the 1+3 layout, which is not beneficial for 4:3 monitors. Note that the following menu settings do not apply for all TANDBER G MXP syst[...]

TANDBERG 770/880/990 MXP 124 Normal Output format is optimized fo r Normal VGA monitors (4:3) Wide Output format is optimized for Wide VGA monitors (16:9) Wide screen VGA or TV monitor in Normal (stretched) mode. Wide screen VGA or TV monitor In Wi de (native) mode. VGA Out Mode VGA Out Mode makes it possible to specify which signal to send to the [...]

General Use 125 WXGA (1280x768) 60Hz SVGA 800x600 75Hz VGA output format is forced to SVGA format (800x600) 75Hz XGA 1024x768 60Hz VGA output format is forced to XGA format (1024x768) 60Hz VGA Out Quality for Wide XGA: If VGA Monitor Format is set to Wide, PC Pictur e Format is s et to Normal, VGA Out Quality is set to Auto, the layout on the monit[...]

TANDBERG 770/880/990 MXP 126 5.1.9 Software Options The system requires a valid option key to activa te MultiSite and/or Presenter functionality. In order to activate additional band width, you need to enter a bandwidth key. A restart of the system is required after entering a new option a nd/or bandwi dth keys. If the key is invalid, the original [...]

General Use 127 5.1.10 Date and Time Settings NTP IP This is the NTP time server address from whi c h the system can get updated time information. See IP Services for more details. Auto The NTP IP will be provided by the DHCP server. Manual The NTP IP address is set manually. IP Address The IP Address for obtaining the date and time information. Ti[...]

TANDBERG 770/880/990 MXP 128 5.2 Menu Settings Menu Settings contain the settings:  Input Editor Language  Menu Timeout In Call  Menu on TV  Menu on PC  Balloon Help  Number Key Mode  Administrator Password  Kiosk Mode Settings  Startup  Icons[...]

General Use 129 5.2.1 Input Editor Language When the Input Editor Language is set to Chinese, Korean or Jap anese the user will be able to enter Chinese / Korean / Japanese characters into an input field like the System Name or Phone Book, using the remote control.[...]

TANDBERG 770/880/990 MXP 130 5.2.2 Menu Timeout In Call The Menu appears on the bottom line of the screen. Set Menu Ti meout In Call to On if you want the menu to time out automatically when you are in a call. On The menus will time out automatically after 15 seconds if there is no activity on the remote control. Menu timeout does only apply whe n [...]

General Use 131 5.2.3 Menu on TV The Menu on TV setting decides if the menu shall be displayed o n the TV screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On a nd vice versa. On The menu is available on the TV screen . Off The menu is not available on the TV screen. Note that if the menu has disappeared from [...]

TANDBERG 770/880/990 MXP 132 5.2.4 Menu on PC The Menu on PC setting decides if the menu shall be displayed o n the PC (VGA screen) screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on P C is On and vice versa. On The menu is available on the PC screen. Off The menu is not available on the PC screen. Note that if the m[...]

General Use 133 5.2.5 Balloon Help It is possible to enable / disable the ballo on help window. On Choose On if you want help text windows to appear. Off There will be no help text window.[...]

TANDBERG 770/880/990 MXP 134 5.2.6 Number Key Mode When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen. The system can b e configured to act automatic or ma nual. While in a call, the user presses a numb er key to: • add another call • dial extension numbers • use camera presets Setting Nu[...]

General Use 135 Settings for Remote Control Number Keys while in a call: Add Call While in a call, the Call Menu will automatically app ea r when a number key is pressed on the remote control. This will enable the user to add another call. Touch tones While in a call, the Touch Tone s Mode will automatically become active when a number key is press[...]

TANDBERG 770/880/990 MXP 136 If you have no stored presets on y our system, you are likely not to use presets. Therefore the presets option is not present in the dialog box. Press arrow key to navigate in the list. Press OK on the remote control to select the desired ent ry. Press a number key while in a call, when having no MultiSite and having st[...]

General Use 137 5.2.7 Administrator Password It is recommended to put an Administrator Passw ord on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Settings from the Cont rol Panel. This will prevent occasional users from going in to system settings. With an admi[...]

TANDBERG 770/880/990 MXP 138 5.2.8 Kiosk Mode Settings Kiosk Mode In Kiosk Mod e t he system is set to a sim plified st ate where it can be contro lled wit h just the four arrow keys and OK. You will get a simplified on-screen menu with only basi c functionality available:  make calls (using pred efin ed contacts in the phone book)  receive c[...]

General Use 139 If Language Menu is enabled you will first see the lan guag e selection menu. Select languag e and the Welcome Menu will be displayed wit h your desired language. In a call, the system will display Far End video in full screen. If Max Call Length is set to a value and the system is in a call, the system will di splay a warning when [...]

TANDBERG 770/880/990 MXP 140 Kiosk Mode - Auto Dial* On The system will automatic ally dial to t he first contact in the Phone Book when he handset is lifted. If this contact is busy, t he system will call the seco nd number in the Phone Book and so on. If the user places t he handset in the cradl e, the system will switch to Speaker Mode. Only the[...]

General Use 141 5.2.9 Startup Welcome Menu The Welcome Menu contains the Menu, System Stat us, your System Nam e and dial in numbers. On The Welcome Menu is sh own when the system wakes up from st andby mod e. Off The Welcome Menu is not shown when the system wakes up from standby mode. Press the OK button to open the welcome menu. Welcome Picture [...]

TANDBERG 770/880/990 MXP 142 Off Welcome text is not displayed on the wel come m enu. Welcome Text You can change the welcom e text to any text you like, instead of the default text. Remember t hat Display Welcome Text must be On to be able to edit the welcome text.[...]

General Use 143 5.2.10 Icons The following indicator ico ns may be set to on or off:  Mic Off  Volume Off  On Air  Encryption  Bad Network  Telephone See On-screen Indicators for details.[...]

TANDBERG 770/880/990 MXP 144 5.3 Presentation Settings Presentation Settings contain:  Presentation Start  H.239  Startup Video Source  Presentation Source  Snapshot Source  Auto-Display Snapshot  PIP Placing  Presentation Rate  VNC Settings[...]

General Use 145 5.3.1 Presentation Start If your system has Dual Stream capa bil ities, y ou can show two video streams at the same time (see also Dual Stream ). Presentation St art is Auto by default. This means that you will start Dual Stream (a second video st ream ) automatically when starting a p re sentatio n. Du al Stream requires the Presen[...]

TANDBERG 770/880/990 MXP 146 5.3.2 H.239 H.239 supports transmission of two video st ream s. It combi nes elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Dual Video Stream* Enabled Enables H.239 Disabled Disables H.239 * The TANDBERG 550 MXP can only receive Dual Video Stream.[...]

General Use 147 5.3.3 Startup Video Source The Startup Video Source is the video source on display w hen the system wakes up from standby mode. If you use Main Camera as star t up source, the system will start with Main Camera every time the system wakes up from stan db y, regardl ess of what the previous user was using. You can change Startup Vide[...]

TANDBERG 770/880/990 MXP 148 5.3.4 Presentation Source The Presentation Source is connected to the Pr esentation button on the remote. Pressin g the Presentation button will put the Pr esentation Source on display. Presentation Source is PC by default*. You can change the Pre sentati on Source to any video source and none. Choosin g none results in[...]

General Use 149 5.3.5 Snapshot Source When you take a Snapshot, you get a snapshot of the Snapshot Source. Current is the default Snapshot Source. This means that you take a sn apshot of the video source that is cu rrently active. You can change the Snapshot Source to any vi deo source. In this way you ca n prog ram the snapshot key to apply only f[...]

TANDBERG 770/880/990 MXP 150 5.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Di spl ay Snapshot Manu al if you wish not to have them displayed on the sc reen when they are sent or received. The snapshots will be sent and received, but not di splayed. With Auto-Display Snapshot set for Manual, you must[...]

General Use 151 5.3.7 PIP Placing PIP Placing lets you decide where the PIP shall appear. You can of course m ove the PIP with the Layout button on the remote anytime. Top Right PIP is placed in the Top Right corner. Bottom Right PIP is placed in the Bottom Right corner. Bottom Left PIP is placed in the Bottom Left corner. Top Left PIP is placed in[...]

TANDBERG 770/880/990 MXP 152 5.3.8 Presentation Rate When setting up a call with H.323 the ba ndwidth can be controlle d by the user. The Presentation Rate is expressed in p ercent of the Call Rate and shall reflect the H.323 Presentation Rate settings of the sender. The settings are 25%, 50% and 75% of the total available video stream.[...]

General Use 153 5.3.9 VNC Settings VNC Settings is necessary when using a VNC present ation. Please see chapter, PC Soft Presenter and VNC, for more informatio n on ho w to use VNC. Address The IP-address of the PC with the V NC software installed. To find the IP- address of the PC, place the mouse poi nter on the V NC p rogram icon in the lower ri[...]

TANDBERG 770/880/990 MXP 154 5.4 Call Quality Call Quality contains the settings:  Video Algorithm  Audio Algorithm  AAC-LD 128kbps  Natural Video  Max Upstream Rate  Video Quality  Call Settings[...]

General Use 155 5.4.1 Video Algorithm The system will automatically select the best video algorithm b ase d on the video source and the capabilities of the remote system. Use this menu to disabl e video al gorithms in case you have interoperability issues calling other systems. H.264 Bandwidth efficient video compression and decomp re ssion. H.263 [...]

TANDBERG 770/880/990 MXP 156 5.4.2 Audio Algorithm The system will automatically select the bes t audio al gorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio , or if you have in teroperabi lity issues calling other systems. G.722 High[...]

General Use 157 5.4.3 AAC-LD 128kbps (stereo audio) Specify a call rate for 128kbps AAC-LD. From this call rate and abo ve, "128kbps AAC-LD" is available. On lower call rat es "64 kbps AAC-LD" is av ailable. Stereo audio require s twi ce the bandwidth as mo no CD-quality audio. Therefore we re commend to enable stereo audio on h[...]

TANDBERG 770/880/990 MXP 158 5.4.4 Natural Video Choosing Natural Vide o will enable 60 fields* per se cond true interlaced pictu re for high m otion video. The use of Natural Video requires the H. 263+ and H.263++ video protocols. Natu ral video will be disabled in H.323 MultiSite calls and in H.320 Continu ou s Presen ce Mul tiSite calls. Auto Wh[...]

General Use 159 5.4.5 Max Upstream Rate (kbps) The Max Upstream Rate (kbps) defines the desired maximum transmitted call rate. This is to be able to limit the outgoing bandwidth whilst keeping th e maximum incomi ng bandwidth, especially useful for home offices wit h different upst ream and downstream ra tes, typically ADSL.[...]

TANDBERG 770/880/990 MXP 160 5.4.6 Video Quality The different video sources need differe nt Video Qual ity Settings. Main Camera, VCR, AUX and Split Screen have Motion as default. PC, Docume nt Came ra and VNC have Sharpness a s default. Motion* Optimized for smooth motion video (CIF/SIF or w288p for low ba n dwidths, 448p/400p, Interlaced CIF (iC[...]

General Use 161 Sharpness*: Improved quality of detailed images and grap hics, lower frame rate, ideal for enhancing quality at lower bandwidths.  4CIF will be used from a PAL video input, Digital Clarity  4SIF from NTSC, Digital Clarity  w720p will be used from a wide format (HD720p) input  VGA/SVGA/XGA from PC, Digital Clarity IVM Res[...]

TANDBERG 770/880/990 MXP 162 5.4.6.2 Native Resolutions The following live video resolutions are suppo rted on the system*: Native NTSC:  4SIF (704 x 480 pixels), Digital Clarity  400p (528 x 400)  iSIF (352 x 480 pixels), Natural Video  SIF (352 x 240 pixels) Native PAL:  4CIF (704 x 576 pixels), Digital Clarity  448p (576 x 448)[...]

General Use 163 5.4.7 Default Call Settings Call Settings are connected with Call Settings in the call menu. If you leave Call Settings unchanged when making a call, the syst em will use the default Call Settings in the call. In addition to the Call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.320 Auto bandwid[...]

TANDBERG 770/880/990 MXP 164 Select SIP to ensure that the call is set up as an SIP call. Bandwidth Bandwidth decides the qu a lit y of the video picture. When set to Auto the system will establ ish a conn ection using a proper bandwidth for the call, typically 384kbp s for ISDN calls and 768kbp s for IP calls. When set to Max the system will set u[...]

General Use 165  Enter the second number in the Call Settings field. For 128 kbps ca lls that use b onding, ignore the second number field and ju st enter one number to be dialed. Using sub-address / extension addre ss / MCU password Sub-address is used to address di ffe ren t systems on the same ISDN line and is primarily used in European Count[...]

TANDBERG 770/880/990 MXP 166 5.5 Audio Audio contains the settings:  Inputs  Outputs  Echo Control  Stereo Settings  Audio Leveling (AGC)  Alert Tones and Volume  Graphical View[...]

General Use 167 5.5.1 Inputs Mic 1- 2 and Audio input 3-4 By default, all inputs are enabled. Just plug in an au dio sou rce and it is active. Audio inputs that are On will automatically be mix ed. Unconnected inputs will automatic ally be muted. Select Off to prevent audio/noise from connected b ut unused in puts. The activated audio so urce s are[...]

TANDBERG 770/880/990 MXP 168 To help adjusting the input levels there is al so a Peak Performance meter sho win g the peak audio volume for each of the audio input s. The level should be adju sted so that the Peak Performance meter never reaches the maximum valu e to avoid the acoustic echo canceller to malfunction due to overload of the microphone[...]

General Use 169 TANDBERG Audio Science m icroph one elements: Audio Technica AT-861P Z and Crown PZM- 6D Signal levels - microphone inputs Clipping level Nominal level Input menu level settings Vpp dBu dBu 0.0 dB 83.0 mVpp -28.4 dBu -46.4 dBu 1.5 dB 69.8 mVpp -29.9 dBu -47.9 dBu 3.0 dB 58.8 mVpp -31.4 dBu -49.4 dBu 4.5 dB 49.4 mVpp -32.9 dBu -50.9 [...]

TANDBERG 770/880/990 MXP 170 Signal levels - line level inputs Clipping level Nominal level Input menu level settings Vpp dBu dBu 0.0 dB 15.5 Vpp 17.0 dBu -1.0 dBu 1.5 dB 13.0 Vpp 15.5 dBu -2.5 dBu 3.0 dB 11.0 Vpp 14.0 dBu -4.0 dBu 4.5 dB 9.2 Vpp 12.5 dBu -5.5 dBu 6.0 dB 7.8 Vpp 11.0 dBu -7.0 dBu 7.5 dB 6.5 Vpp 9.5 dBu -8.5 dBu 9.0 dB 5.5 Vpp 8.0 d[...]

General Use 171 5.5.2 Outputs Audio out 1 - 2 Audio out 1 is intended for connection to televisions or audio amplifi ers. Audio out 2 is intended for connection to a VCR or other re co rding equipment. The signal is a mix of audio from far end and local end (exce pt VCR in). Note that audio out 2 never should be connected to a loud spe aker placed [...]

TANDBERG 770/880/990 MXP 172 Signal levels - line level outputs* Absolu te max. output level Nominal level Output menu level settings Vpp dBu dBu 0.0 dB 1.2 Vpp -5.5 dBu -23.5 dBu 1.5 dB 1.4 Vpp -4.0 dBu -22.0 dBu 3.0 dB 1.6 Vpp -2.5 dBu -20.5 dBu 4.5 dB 1.9 Vpp -1.0 dBu -19.0 dBu 6.0 dB 2.3 Vpp 0.5 dBu -17.5 dBu 7.5 dB 2.8 Vpp 2.0 dBu -16.0 dBu 9.[...]

General Use 173 5.5.3 Echo Control Mic 1-2 Each of the 2 microphone i nputs h as a separate acoustic echo can celle r. One echo canceller per input provides more sophisticated co ntrol t han havin g one commo n canceller for all micropho nes. In addition to echo cancellation, the system has built-in noise reduction (NR). NR redu ce s constant backg[...]

TANDBERG 770/880/990 MXP 174 5.5.4 Stereo Settings Settings Output response Out 1 Mode* Stereo input mode Stereo Speakers Audio out 1 Audio out 2 Analog Off Off Loudspeaker mono VCR Analog Off On Loudspea ker left Loudspeaker right Analog On Off Loudspea ker mono VCR Analog On On Loudsp eaker left Loudspeaker right SPDIF Off Off Loudspeaker mono VC[...]

General Use 175 If the system is connected to a Digital NAM , stereo sou nd on the loudspeake rs shall be present if a stereo input signal is conn ect ed to the inputs VCR-Left and VCR-Right or a stereo signal is received from the Far End. If the system is not connected to a Digi tal NAM , stereo soun d on the loudspeaker o utputs will be present i[...]

TANDBERG 770/880/990 MXP 176 5.5.5 Audio Leveling (AGC) On Select On to allow automatic adjustments (Automatic Gain Control ) of audio leve ls. When On, the AGC maintains the audio sign al level at a fixed value by attenuating strong signals and am plifying we ak signals. Very weak signal s, i.e. noise alone, will not be amplified. Off Audio leveli[...]

General Use 177 5.5.6 Alert Tones and Volume Video Call Alert Tone and Telephone Alert Tone To help distinguish between incoming video calls a nd ordinary telephone calls, it is re commended to use different ringing tones for video calls and telep hone calls. Alert Volume You may change the volume level for the selected ri nging ton e. Alert Speake[...]

TANDBERG 770/880/990 MXP 178 5.5.7 Graphical View Graphical View The graphical view is a visual presenta tion of the audio inputs and audio o utputs. • The Inputs + Far End In are listed on the le ft, showing the name of the input sources. • The outputs + Far End Ou t are listed on the bottom, showing the name of the output sources. • The gre[...]

General Use 179 5.6 Video Video contains the settings:  Camera Tracking Mo de  MCU Status Line  Floor to Full Screen  Web Snapshots  MultiSite Picture Mode  Video Name[...]

TANDBERG 770/880/990 MXP 180 5.6.1 Camera Tracking Mode Slow The system waits a while before zoomi ng in on a si ngle person speaki ng. Suitable when wide-angle images are preferred over close-up images. Normal Should be used in regular meetings. Fast The system quickly zooms in on a sing le person speaking. Suitable when clo se- ups are preferred [...]

General Use 181 5.6.2 MCU Status Line On The MultiSite / MCU / DuoVideo indicat ors will be di splayed and provide information about the conference. Off The MultiSite / MCU / Duo V ideo indi cators will not be displaye d. Auto The MultiSite / MCU / DuoVideo indicat ors will be displayed for a few seconds and then timed out. When grabbing the remote[...]

TANDBERG 770/880/990 MXP 182 5.6.3 Floor to Full Screen When "Floor to Full Screen" is enable d, some one wh o requests floor will be seen by all participants as full screen. Whe n "Floor t o Full Screen" is "Off", someone who request floor in a MultiSite conference using the 5+1 layo ut will be se en in the large squa[...]

General Use 183 5.6.4 Web Snapshots The system is able to generate JPE G snapshots and provide them when requested (as ‘http g et’ or via ftp). See Appendix 6 for descriptions of the possible snapshot files. On Snapshots generation is enabled. Off Snapshots generation is di sabl ed. Note that web snapshots are not gene ra ted if the conferen ce[...]

TANDBERG 770/880/990 MXP 184 5.6.5 MultiSite Picture Mode MultiSite* Picture Mode determines the default lay out of a MultiSite call. Available layouts are: Auto Split, 4 Split, 5+1 Split, and Voice Switched. You can change the layout during a call using the layout option in MultiSite Services. Auto Split Auto Split displays all participants on the[...]

General Use 185 Voice Switched mode * The MultiSite option is not ava ilable on the TANDBERG 77 0 MXP.[...]

TANDBERG 770/880/990 MXP 186 5.6.6 Video Name As a default, the video inputs are given the name s Main Cam, PC, Do c Cam, VCR, AUX or VNC, dependent on what video sources ar e available on yo ur system. The video names cannot exceed eight characters. The nam es corre spond to the video names in the Presentation Menu (Choose Presentation from the Me[...]

General Use 187 5.7 Security Security contains the settings:  Encryption  Encryption Mode  Passwords  Camera Standby mode[...]

TANDBERG 770/880/990 MXP 188 5.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption. MultiSite calls*: In order to have encrypt ed MultiSite calls, all sit[...]

General Use 189 5.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other si tes. For sites that do not support AES encryption, DES encryption will be tried. AES The system will try to use AES with 128 bits encryption when setting up calls. If AES is not supported by the other[...]

TANDBERG 770/880/990 MXP 190 5.7.3 Passwords Administrat or Password, I P Access Pa ssword , Streaming Password, VNC Password, Access Code and Remote Software Upgrad e password ar e duplicated from their respe ctive menu s. Using the Security menu g ives you a qui ck way to change all password s of the sy stem.[...]

General Use 191 5.7.4 Camera Standby Mode There is a setting to the Security menu called Camera Standby mode On (default)/Off. When Camera Standby mode is On, the came ra turns away when stand b y is activated. When the system is activated the camera turns b ack to norm al position. On The camera will turn away when stand by mode is activated and t[...]

TANDBERG 770/880/990 MXP 192 5.8 Network The network menu contains:  ISDN-BRI Settings  LAN Settings  Network Profiles  Data Port[...]

General Use 193 5.8.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the fo llo wing settings: 1. Set ISDN switch type 2. Enter ISDN line numbers (and SPIDs, if required) 3. Disable unused lines Some software versions do not support 6 ISDN li nes, t herefo re some of the Line Setup entries may be grayed out. ISDN[...]

TANDBERG 770/880/990 MXP 194 call a terminal with a sub addre s s, sep arate the ISDN telephone number a nd the sub address with a ‘*’. Note that this service ha s limited access on some ISDN networks. Example : 12345678*2 (up to four digit sub add resses are possible). Validate Numbers / MSN (Multiple Subscriber Number) The use of MSN (Multipl[...]

General Use 195 5.8.2 LAN Settings LAN Settings contain:  IP Settings  H.323 Settings  SIP Settings  Wireless LAN Settings  SNMP Settings  IP Services  Quality of Service  802.1X Settings[...]

TANDBERG 770/880/990 MXP 196 5.8.2.1 IP Settings Remember to restart the system after making cha nge s to IP Settings. This can be done by selecting the “Save and Restart” at the b ottom of the IP setting men u. Changes in IP Settings menu will not have any effect until the system is restarted. IP Protocol IPv4 IP version 4 supported. IPv6 IP v[...]

General Use 197 Ethernet Speed Auto The codec will auto-dete ct t he speed/d uplex on the LAN. 10/Half The codec will conn ect to the LAN u sing 10Mbps speed/Half Duple x. 10/Full 10 Mbps speed/Full Duplex . 100/Half 100 Mbps speed/Half Duplex. 100/Full 100 Mbps speed/Full Duplex. IP Access Pass word By setting an IP Access Password on the s ystem,[...]

TANDBERG 770/880/990 MXP 198 DNS Settings DNS Server 1-5 DNS Server defines the network addre sses fo r DNS serve rs. Up to 5 addresses may be specified. If the network addresses are unkno wn, please contact your administrator or Internet Service Provider. DNS Domain Name DNS Domain Name is the default domain name suffix which is added to unqu alif[...]

General Use 199 5.8.2.2 H.323 Settings E.164 alias This is the E.164 address of the system . The E.164 addre ss is equivalent to a telephone number, sometimes combined with access code s. Valid characters are 0-9, * and #. Whe n using a gatekeeper, the system will send a messag e to the gatekeeper containing both the E.164 addre ss and the H.323 ID[...]

TANDBERG 770/880/990 MXP 200 Gatekeeper Settings Gatekeeper Discovery Auto The sy stem will automatically try to register to any available gate k eepe r. If a gatekeeper responds to the request sen t from the codec within 30 second s this specific gatekeeper will be use d. This require s auto di scovery on the gatekeeper as well. If no gatekeeper r[...]

General Use 201 Multiple H.323 Aliases is set to Off. If set to Off, the system will register a si ngle H.3 23-IDs on the Gatekeeper b ased on the following priority: • H.323 ID • International Name • System Name The default setting for Multiple H.323 Aliases is Off.[...]

TANDBERG 770/880/990 MXP 202 CallManager Settings CallManager IP This is the CallManager IP-address that is used if you specify H.323 Call Setup: CallManager.[...]

General Use 203 Advanced H.323 Settings The Advanced H.323 Settings only have an effect if t hey are supported by your IP infrastructure. NAT NAT, Network Address Translation, is used when a PC and a vide o comm unication system are connected to a router with NAT su ppo rt. NAT support in the video communicati on system enables proper exchange of a[...]

TANDBERG 770/880/990 MXP 204 5.8.2.3 SIP Settings Mode On Setting the SIP mode to on will enable the system for incoming and outgoin g SIP calls. Off Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system. Display Name The Display name part of the SIP Addre ss (U RI) is usually a full name or system name. Examples:[...]

General Use 205 Server Address: <text field> Examples: “sipserver.ex ample.c om” “sipserver.example.com:5 060” “10.0.0.2” “10.0.0.2:5061” Authentication User Name This is the user name part of the credent ials used to authenticate toward the SIP Server. User name: <text field> Password This is the password part o f the c[...]

TANDBERG 770/880/990 MXP 206  Draft-ietf-avt-rfc2429-bis-05.txt - Draft for advan ced vi deo signaling including resolution, mpi, annexes and custom formats.  RFC 3047 RTP Payload Format for ITU-T Recommendation G.7 2 2.1  RFC3581 An Extension to the Session Initia tion Protocol (SIP) for Symmetric Response Routing  RFC3984 RTP Payload [...]

General Use 207 5.8.2.4 Wireless LAN Settings SSID (Service Set Identification ) Example: “WLANNETWORK”. This defines a lo cal n e twork id for this wireless region. It must be the same for all end points and the access point. An endpoint will find the acce ss point if the SSID is correct, however if the encryption key is faulty it will not tra[...]

TANDBERG 770/880/990 MXP 208 Encryption Select Encryption if you want to use WEP encryption on your Wireless LAN conne ction. Increased encryption level will decrease performance. Use Key Select which of the keys s hown below you want to use. Key 1- 4 The 64-bit keys can con sist of a leading star (*) and 5 characters. The 128-bit key can consist o[...]

General Use 209 5.8.2.5 SNMP Settings SNMP Settings SNMP Trap Host identifies the IP-address of the SNMP manager. SNMP (Simple Network Management Protocol, SNMP Ver 1) is used for m onitoring and co nfiguring of different entities in a network. The system's SNMP Agent resp ond s to requests from SNMP Managers (a PC program etc.). SNMP traps ar[...]

TANDBERG 770/880/990 MXP 210 5.8.2.6 IP Services NTP IP This is the NTP time server address from whi c h the system can get updated time information. This is a requirement for proper o pe ration if H.235 authentication is implemented. The Network Time Protocol (NTP) i s used to sync hronize the time of the system to a reference time server. The NTP[...]

General Use 211 5.8.2.7 Quality of Service QoS Type Off No QoS is used. Diffserv Diffserv QoS method is used. Please see belo w for d etails. IP Precedence IP Precedence QoS method is used. Please see below for details. IP Precedence Video Used to define which priority audio, video, dat a and signalin g should have in the network. Th e higher the n[...]

TANDBERG 770/880/990 MXP 212 Auto will provide the following priority: Audio 4 Diffserv Video Used to define which priority Audio, Video, Da ta and Signaling packets sho uld h ave in an IP network. The priority ranges from 0 to 63 for each type of packets. Diffserv Telephony Used to define which priority Audio packets sh oul d have in an IP network[...]

General Use 213 5.8.2.8 IEEE 802.1x 802.1X The system may be connected to an IEEE 802.1x LAN network. Supported 8 02.1x protocols are EAP-MD5, EAP-PEAP and EAP-TTLS. The 802.1x authent ication are enabled by setting 802.1x Mode to On. On 802.1x authentication enabled Off 802.1x authentication disabled Anonymous Identity The 802.1x Anonymous ID stri[...]

TANDBERG 770/880/990 MXP 214 5.8.3 Network Profiles This menu consists of 7 network profiles; a prefix and a suffix can be added for each p rofile. If you add a prefix/suffix to a profile, this prefix/su ffix will automatically be add ed in front/back of the number being dialed. Example: 0 is added as a Call Prefix to the 2nd profile, ISDN. If you [...]

General Use 215 5.8.4 Data Port The system provides up to two standard RS232 seri al ports to allow a computer to be conne ct ed for data transfer and control purposes. Note that wh en co nnecting to a PC the connecting cable must be a straight through RS232 cabl e. Baud Rate, Parity, Data bits and Sto p bits If you wish to connect a PC to Data por[...]

TANDBERG 770/880/990 MXP 216 5.8.5 Restore Default Settings Restore Default Settings will restore all system setti ngs. Note that this will not affect your Call Directory information, Network Type, Li ne Setup numbers or your SPID numbers.[...]

217 6 Peripheral Equipment Using the optional peripheral device s outlined in this chapter and the many others available, you will be able to build your own applications for us e with the system, thereby better integrating the system into your business environ ment. This chapter will explain how to connect periphe ral equipment to your system. Firs[...]

TANDBERG 770/880/990 MXP 218 6.1 Interfaces 6.1.1 Video 5 Video Inputs  1 video input used by the built-in camera.  1 video input supporting S-Video through a Mini-DIN con nector.  2 video inputs supporting comp osite signals through RCA connect ors.  1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) inpu [...]

Peripheral Equipment 219 4 Video Outputs  1 S-Video output, Mini-DIN connector.  2 composite video outputs, RCA conne ctors.  1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) output, analog or digital. The first Mini-DIN connector and the first RCA connector provide ma in video (in coming/outgoing video and [...]

TANDBERG 770/880/990 MXP 220 Supported DVI cables: TANDBERG supports DVI-D Single -Lin k , DVI- A and DVI-I Single-Link format cables. DVI-D cables transmit digital T.M.D.S. signal s, DVI-A cabl es transmit analog VGA signals a nd DVI-I cables can transmit either digital or anal og signals. It is possible to extend existing DVI cables by the use of[...]

Peripheral Equipment 221 Signal name CON. 3 Pin CON. 1 Pin CON. 5 Pin CON. 2 Pin CON. 4 Pin Cable color DDC Clock 6 15 Orange DDC Data 7 12 White Vertical Sync 8 14 Yellow DDC Power (+5V) 14, 16 9 Red Digital return 15 5, 10 Black RGB Red C1 1 Red Coax RGB Green C2 2 Green Coax RGB Blue C3 3 Blue Coax Horizontal Sync C4 13 Brown RGB Return C5 6, 7,[...]

TANDBERG 770/880/990 MXP 222 VGA to DVI-A Cable Pinouts* : VGA to DVI-A cable male-male 5m black, maximum length 5m. No Item Description 1 Cable UL20276 3Coax*30#+IP*28#+5C*28#+AEB Black OD:7.0mm L-5000m m 2 Connecto r HDD 15P Male Black 3 Connecto r HDD 17P Male Black 4 Tube PE Tube Black OD:1.5*10 / 1.0*15 / 1.5*8 / 2.5*10 / 1.5*15 / 5.0*10 mm 5 [...]

Peripheral Equipment 223 6.1.2 Audio 4 Audio Inputs  2 microphone inputs (balanced, 24V phantom powere d) via XLR co nnectors.  2 audio inputs (line level) via RCA connectors. All audio inputs are active by default. For further information, refer to chapter Audio . Audio input connector specification: Connector label Microphone(s) Audio input[...]

TANDBERG 770/880/990 MXP 224 2 Audio Outputs  1 output (line level) via RCA connector providing audio from far en d in addition t o dial tones. This output is used by the monito r. This output also supports S/PDIF.  1 VCR output (line level) via RCA conne ctor providin g a mixed signal between audio from the local side (except from the VCR in[...]

Peripheral Equipment 225 6.1.3 Network Ethernet: 770MXP: 1 x Ethernet (RJ-45 Jack) LAN interface (10/ 100 Mb ) up to 768kbps 880MXP: 1 x Ethernet (RJ-45 Jack) LAN interface (10/ 100 Mb ) up to 1.1 Mbps depending on the bandwidth option installe d. 990MXP: 1 x Ethernet (RJ-45 Jack) LAN interfac e (10/100 Mb ) up to 2 Mbps or 2.3 Mbps depending on th[...]

TANDBERG 770/880/990 MXP 226 6.1.4 Data port The data port(s) are imple mented as Data Comm unications Equipment (D CE). The connectors used are female 9-pin D-subs. Signal name Direction Pin number Carrier detect, CD From DCE 1 Receive data, RXD From DCE 2 Transmit data, TXD To DCE 3 Data terminal ready, DTR From DCE 4 Signal ground, GND 5 Data se[...]

Peripheral Equipment 227 6.2 Document Camera A document camera can be used for sho wing text, diagram s and a variety of graphical material as well as small three-dimensio nal obje cts. How to use a document camera with your system: 1. Connect the document camera to the Do c Cam input, if available, on the system. 2. Open the Presentation menu fr o[...]

TANDBERG 770/880/990 MXP 228 6.3 DVD / VCR DVD/VCR Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on t he VCR a nd the Audio In (VCR) on the system. Choose VCR from the Presentation menu to activate the VCR in put . Make sure that Audio In (VCR) is On (see[...]

Peripheral Equipment 229 Note that a system with one video output and one mixed (local and far end) audi o output is required for recording. For playback, a system with on e video input and one audio input without integrated echo cancellation is required.[...]

TANDBERG 770/880/990 MXP 230 6.4 Additional Cameras Extra fixed Cameras You can connect extra fixed camera s to your sy stem, for example, a whiteboard camera. Con nect the video output of the additional camera to one of the available Video inp uts on the system. Note that additional controllable camera s are only avai lable for some roll-about sys[...]

Peripheral Equipment 231 6.5 Additional Microphones If your environment is such that you require more than one microphone for you r room, e.g. you have a whiteboard at a distance from your table microphone, it is possible to con nect ad ditional microphones to your system. See Appendix 4 for more information. Note that this requires a system with m[...]

TANDBERG 770/880/990 MXP 232 6.6 The TANDBERG DNAM and Speakers TANDBERG 6000 MXP Profile, T ANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro The TANDBERG Digital Natural Audio Module, DNAM*: The DNAM audio system is built on two spe cially desi gned and separate modules; the DNAM audio amplifier and the DNAM loudsp e ake[...]

Peripheral Equipment 233 TANDBERG 8000 MXP DNAM configuration TANDBERG 6000 MXP Profile DNAM configuration Center Speakers + In tegrated Stereo Speakers The DNAM Amplifier*:  3 x 50W continuous average Center Out put Powe r (lo ad specified by DNAM Center Speakers).  2 x 50W continuous average Stereo Output Powe r (lo ad specified by TANDBERG[...]

TANDBERG 770/880/990 MXP 234 The DNAM Loudspeaker Cabinet (Center Spe aker s)*:  3-way Center Speaker system  Frequency range 50Hz - 2 0kHz  2 x 130mm low- and midrange loudspeakers, 8 ohm s nominal, high quality  1 x 25mm dome tweeter, 6 ohms nominal, high quality  Crossover filtered audio si gnals received from DNAM amplifier  L[...]

Peripheral Equipment 235 The Mini-DNAM audiosystem is built on two specially desig ned and separate modules; the Mini- DNAM amplifier and the Mini-DNAM loudsp ea ker ca binet. The Mini-DNAM loudspea ker cabinet is stereo-configured and based on two version s mad e for fitting both the TANDBE RG 3000 Profile 43’’ and 32’’ systems. The compa [...]

TANDBERG 770/880/990 MXP 236 6.7 Stereo Speaker Kit Note that the following applies only for system s with a stereo S/PDIF output. The Stereo Speaker Kit provides an pair of floor-s tanding lou dsp eakers in addit ion to the built-in DNAM . Using these speakers will ena bl e stereo func tionality in your system and thereby enha nce the sound experi[...]

Peripheral Equipment 237[...]

TANDBERG 770/880/990 MXP 238 6.8 Telephone Add-On The system has a built in audio bri dge* that can br ing in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. Note that this requires a system with mix ed audi o output (audio from local and far end ) an d one audio input without integrated echo cancelli ng. In addition to using I[...]

Peripheral Equipment 239 6.9 Dual Monitor Note that this requires a system with du al monitor vid eo output. It is possible to install the system in a Dual M onitor configuration. The Du al Monitor can be used to show full screen selfview, still images and Duo Vi deo. To use the system in the Dual Monitor configura tio n: 1. Connect "Video Out[...]

TANDBERG 770/880/990 MXP 240 6.10 XGA Monitors and Projectors (Optional) Some TANDBERG systems can be delivered with op tional single or dual TV/X GA monitors. It can also be connected to any DVI/VGA/PAL or NTS C display. Note that this requires a system with min imum one DVI-I output.[...]

Peripheral Equipment 241 6.11 VESA Display Power Management Because of the tremendous amount of energy co ns um ed by monitors when operating, the system will reduce power consu m p tion and extend monitor lifecycle by su spending the (switch off) monitors and projectors when the syste m goes into sleep/standby. This applies for all VESA Display Po[...]

TANDBERG 770/880/990 MXP 242 6.12 Digital Monitor Power Management DMPM is monitor power management a pplied over the digital DVI interface. TANDBERG supports DMPM in softwar e F2 and ab ove. Six monitor power stat es are defined. Monitor On Power state Transmitter (TANDBERG codec) and receiver (Moni t or) a re powered and active. This po wer state[...]

Peripheral Equipment 243 6.13 Extended Display Identification Data (EDID) Extended Display Identification Data (EDID) is a VESA standard data format that will allow the system to communicate its ca pabilities, including vendor information like the supported VGA - formats and frequency range limits to a PC con ne cte d to the XGA/DVI input. Note tha[...]

TANDBERG 770/880/990 MXP 244 Tested and verified monitors, EDID & Timing Listed below are some of the monitors TANDBERG h ave tested an d verified against: ADI A715 Dell W1700 Dell W1900 EIZO L367 EIZO F730 ErgoScan 400S Hitachi CM640ET Hitachi CM769ET IBM 9494-HBO IBM G97 IBM E74 IBM 6743-60N JVC LT-23X475 JVC LT- 23C50BU JVC LT-23X576 LG L320[...]

245 7 Appendices Appendices:  Appendix 1: Technical Specification  Appendix 2: Bandwidth Information  Appendix 3: Environmental considerations  Appendix 4: Guidelines for setting up rooms for video meeting s  Appendix 5: Security  Appendix 6: Using the file system  Appendix 7: Web Interface  Appendix 8: Connecting the system[...]

TANDBERG 770/880/990 MXP 246 Appendix 1: Technical Specifications Technical Specification UNIT DELIVERED COMPLETE WITH: Wireless remote control, W.A.V.E II camera, microphone and cables. BANDWI DTH 990 MXP: H.320 up to 512 kbps H.323 & SIP up to 2 Mbps 880 MXP: H.320 up to 384 kbps H.323 & SIP up to 1.1 Mbps 770 MXP: H.320 up to 128 kbps H.[...]

Appendices 247 VIDEO FORMAT NTSC, PAL, VGA, SVGA, XGA, W-XGA, SXGA and HD720p LIVE VIDEO RESOLUTIONS NATIVE NTSC: 400p (528 x 400 pixels) 4SIF (704 x 480 pixels), Digital Clarity Interlaced SIF (iSIF 352 x 480 pixels), Natu ral Video SIF (352 x 240 pixels) NATIVE PAL: 448p (576 x 448 pixels) 4CIF (704 x 576 pixels), Digital Clarity Interlaced CIF ([...]

TANDBERG 770/880/990 MXP 248 only) Dynamic Bandwidth adjustments (H.323) NETWORK FEATURES Auto H.320/H.323 dialing SIP Downspeeding Programmable network profiles Intelligent Call Management Maximum call length timer Automatic SPID and line number configuration (National ISDN, GR-2941-CORE) Soft Mux H.331 Broadcast Mode NATO standard KG194/KIV-7 enc[...]

Appendices 249 trademarks of Microsoft Corporation in the United States and/or oth er countries. All other trademarks are property of their respective owners. Contains iType TM from Agfa Monotype Corporati on Service availability may vary from region to region. Pl ease contact your TANDBERG reseller for more information.[...]

TANDBERG 770/880/990 MXP 250 Appendix 2: Bandwidth Information for TANDBERG Endpoints Bandwidth Information for TANDBERG Endpoints Model 8000MXP, 7000MXP 6000MXP, Maestro Bandwidth Point to point ISDN / IP Standard: 768 / 3072 Option: 1920 / 4096 Standard: 768 / 3072 Option: 1920 / 4096 MultiSite Total: 3072kbps 4x768 video + 4 audio 3x1536 video +[...]

Appendices 251 H.264 Up to 2Mbps Up to 2Mbps Picture Mode MultiSite VS, CP4, CP5+1 VS, CP4, CP5+1 Model 990MXP / 990NET MXP 880MXP / 880NET MXP Bandwidth Point to point ISDN / IP Standard: 1920 (IP only) Options: 512 / 1920 990NET: 768 / 1920 Standard: 1152 (IP only) Option: 384 / 1152 MultiSite Total: 2304kbps 4x768 video + no audio 4x512 video + [...]

TANDBERG 770/880/990 MXP 252 Appendix 3: Environmental Considerations Environmental considerations This section explains how to carry out basi c adju s tments and simple tests to en sure that you send and receive the best possi ble image and audio qualit y when u sing your system. Iris control and lighting By default the system camera will use an a[...]

Appendices 253 Appendix 4: Guidelines for Setting up Rooms for Video Meetings Guidelines for setting up rooms for video meetings. The following are a set of guidelines to consider whe n either building a video meeting roo m, or using an existing room for video meetin g s. Lighting:  Low Contrast desired for light intensity. No dark spots.  In[...]

TANDBERG 770/880/990 MXP 254 How to prepare a typical room for video meeting: The illustration below shows the principles of a typical room designed to obtain the best results when using a videoco nfere nce system. If the system has a separate microphone , it shoul d be placed at the front of the table to ensure that all speech will be detected. Th[...]

Appendices 255 Appendix 5: Security Security The system has several features both to prot ect fro m unauth orized use and sy stem access: Access Code: When Access Code is enabled, the user will be as ked to enter an access code before he/ she is able to make a call. The system will verify if the entered access code is valid by checking the code wit[...]

TANDBERG 770/880/990 MXP 256 By setting an IP Access Password on the s ystem, all access to the system using IP (Telnet, FTP and WEB) requires a pa ssword. This p assword can be enabled from telnet or dataport u sing the command: ippassword <ip-passwo rd >. The defaul t IP username and password is "TANDBERG". To remove this password[...]

Appendices 257 backwards compatibility) with extended Diffie Hellma n key distribution via H.320, H.323 and Leased Line con ne ctions. The TANDBERG AES implementation is validated as conforming to the Advanced Encryption Standard (AES) Algorithm, as specified in Federa l Information Processi ng Standard Publication 197, Advanced Encryption Standard[...]

TANDBERG 770/880/990 MXP 258 Appendix 6: Using the File System Using the file system It is possible to access a file sy stem within the TANDBERG sy stem by using ftp: DOS- window: ftp <IP-address of system>, or Web- browser: ftp:// <IP-address of system> Description of the different files: all.prm all settings in the system (including d[...]

Appendices 259 Appendix 7: Web Interface Web Interface It is possible to access and maintain the system remot ely via a local area network (LAN) usin g a standard Web-browser. Conne ct your syste m to a LAN with a Network cable. How to configure your system for web interface: 1. Open Administrator Settings an d choose Network LAN Settings 2. Speci[...]

TANDBERG 770/880/990 MXP 260 Appendix 8: Connecting the System to PRI/T1 (Not available on all TANDBERG systems) Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-inte rfa ce using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.54 Mbps conne ction. The E1/T1-interface must be c[...]

Appendices 261 Appendix 9: Connecting the System to the Switched 56 Network Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adap ter Connecting the system to the SW56 net work u sing a Telesync Adapter is described bel ow. There are different Telesync Adapters for different conf igurat ions of SW5 6 networks. The ne[...]

TANDBERG 770/880/990 MXP 262 Appendix 10: Connecting the System to ISDN Using NT1 Network Adapters Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the system to the S-interface on your first NT1 network adapter. Connect t he other ISDN ca bles to the appropriate NT1 network adapters. C[...]

Appendices 263 Appendix 11: TANDBERG Cameras TANDBERG Precision HD Camera (Available to TANDBERG 8000 M XP, 6000 MXP Prof ile, 3000 MXP Profile*, Maestro MXP and Edge 75/85/95 MXP) Pin-outs and Connectors[...]

TANDBERG 770/880/990 MXP 264 1. Extra Camera In 2. 12V DC Power In 3. HD Video Out, HDMI** 4. Codec – HD Video Out 5. Kensington Lock NOTE! The enclosed TANDBERG Camera Cable s m ust be used! Do not use other camera cables as this might cause problem s with the tr ansfer of video signals from the Precision HD Camera. 8-PIN RJ (shielded modular ja[...]

Appendices 265 The maximum length of the camera cable for mult iple cameras supported by TA NDBERG is 20 m (65 ft). * Applies to T3000 MXP Profile with new hardware. ** Disabled when connected to a TANDBERG system using the TANDBERG Ca mera Cable. This output does not support HDCP (High Bandwidth Digital Content Protection). Precision HD Camera Dim[...]

TANDBERG 770/880/990 MXP 266 Top view:[...]

Appendices 267 (Not available with set top systems) WAVE II Camera Pinouts and Connectors 8-PIN RJ (shielded modular jack): This connector is u sed fo r the power and control signals to the main camera. Pin-8 +12V (presence when connecte d in daisy chain) Pin-7 GND Pin-6 GND Pin-5 RXD (in) Pin-4 TXD (out) Pin-3 +12V Pin-2 GND Pin-1 + 12V Standard P[...]

TANDBERG 770/880/990 MXP 268 Pin-5 GND Pin-4 RXD (in) Pin-3 TXD (out) Pin-2 Presence (+12V in daisy chain) Pin-1 GND Dimensions Front view: Sid e view : Re ar view : Underside vie w :[...]

Appendices 269 Appendix 12: Remote Control (TRC3 / TRC4) Remote Control (TRC 3 / TRC4) The TANDBERG remote control transmits IR -signals usin g the following parameters: Protocol Siemens SDA2208 Reference frequency 485kHz Address 4 & 7 IR wavelenght 940nm IR carrier ferquency 30kHz[...]

TANDBERG 770/880/990 MXP 270 Remote Control Key Code Map: Button codes Remote Control (TRC 3) Remote Co n trol (TRC 4) TANDBERG TRACKER Dec Hex Address Button name Address Button name Address Button name 0 0 1 1 0 NUMBE R 1 0 NUMBER 1 2 2 0 NUMBE R 2 0 NUMBER 2 3 3 0 NUMBE R 3 0 NUMBER 3 4 4 0 NUMBE R 4 0 NUMBER 4 5 5 0 NUMBE R 5 0 NUMBER 5 6 6 0 N[...]

Appendices 271 32 20 0 RIGHT 0 RIGHT 33 21 0 OK 0 OK 34 22 0 CALL 0 CALL 35 23 0 END CALL 0 END CALL 36 24 0 PHONE BOOK 0 PHONE BOOK 37 25 0 MENU 0 MENU 38 26 0 CANCEL 0 CANCEL 39 27 0 0 40 28 0 LAYOUT 0 LAYOUT 41 29 42 2A 0 MAIN CAM 43 2B 0 PC 44 2C 0 DOC CAM 45 2D 0 DVD 46 2E 0 AUX 47 2F 0 HELP 4 P0 48 30 0 FAR END 4 P1 49 31 0 PRESETS 4 P2 50 32[...]

TANDBERG 770/880/990 MXP 272 Appendix 13: Cisco CallManager Cisco CallManager registration Configuring an H.323 client on the CallManager 4.0 The registration of a H.323 client in CallM anager is supported on t he CallManager (CCM) 4. 0 software and forward. 1. To configure the CallManager with an H. 323 client, log on to the administration web int[...]

Appendices 273 Appendix 14: Diagnostics Tools for IP Diagnostic Tools for IP To use these tools, will require u sing a P C and setting up a telnet session towards the syste m . Q.931 To show Q.931 trace during a call you n eed to issue the command ‘syslo g on’. One can get traces for RAS, Q.931 and H.245 with th is command. It is a complex trac[...]

TANDBERG 770/880/990 MXP 274 Function Port Typ e Gatekeeper Discovery (RAS) 1719 UDP Q.931 Call Setup 1720 TCP H.245* Range 5555-5574 TCP Video Range 2326-2405 UDP Audio Range 2326-2405 UDP Data/FECC Range 2326-2405 UDP MultiSite + Duo Video (*) Note: While using MultiSite, if a site is di sconnected and re connected without terminating t he entire[...]

Appendices 275 Appendix 15: System Upgrade System Upgrade Before starting the software upgrade of the TA NDBE RG MXP system, please make sure to have the new software file, (for instance s0500 00F 30.pkg ) a nd the Rel ease Key for this software available. Your TANDBERG Partne r will provide this for you. All options and settings will automatically[...]

TANDBERG 770/880/990 MXP 276 Figure 1 3. Enter the Release key in the ‘Release Key’ field and press the ‘Install Software’ button.[...]

Appendices 277 A new page will now be displayed: Figure 2 4. Type in the path to where the new software file is stored, or sel ect the file by using the ‘Browse’ button. 5. The progress for the sw upgrade can be tracked by pressing the ‘telnet’ link in the help text box BEFORE pressing the install button. Please note that this is not a nece[...]

TANDBERG 770/880/990 MXP 278 5) Type in your IP password (def ault is “TANDBERG”) a s pa ssword. 6) Type ‘put <software file name> and press Ente r. The new software file will now be uploaded to the TANDBERG MXP system. 7) When the software upload is com plete, end the ftp connection to the TANDBERG MXP system by typing ‘bye’ in the[...]

Appendices 279 The following page will now be di splaye d: Figure 3 5. Enter the release key for the system to be upgraded in the ‘Rele ase Key’ field. If no release key is given, the Far End System will use the prev iously stored release key if possible. This will work when upgrading from a main release to a dot relea se. 6 Make sure the setti[...]

TANDBERG 770/880/990 MXP 280 In the menu on the system under ‘Control Panel /System Information ’, the installed software should now be displayed as the ‘Software Versi on’.[...]

Appendices 281 Appendix 16: Declaration of Conformity EC DECLARATION OF CONFORMITY MANUFACTURER: TANDBERG Telecom AS PRODUCT NAME: TANDBERG 770MXP TANDBERG 880MXP TANDBERG 990MXP TYPE NUMBER: TTC7-08 DESCRIPTION: Video Conferencing Equipment This product complies with Commissi on Directives:  LVD 73/23/EEC  EMC 89/336/EEC R&TTE 99/5/EEC T[...]

TANDBERG 770/880/990 MXP 282 Appendix 17: Dimensions Dimensions[...]

Appendices 283 Appendix 18: Protocols Supported PROTOCOLS SUPPORTED TCP/IP - Transmission Control Protocol/Internet Protocol A set of networking protocols that provi des conn ectivity over LAN/WAN to any network computer. HTTP - Hypertext Tran sfe r Protocol A protocol used to transfer information on the in ternet. A web-browser interface is used t[...]

TANDBERG 770/880/990 MXP 284 A communications network conn ecting a group of computers, printers, and other devices located within a relatively limited area (for example, a building). WAN – Wide Area Net work A communications network conn ecting geographically separated computers, printers, and othe r devices. SSL - Secure Sockets Layer SSL is a [...]

Appendices 285 Appendix 19: Cable Specifications TANDBERG MXP and Classic E ndpoints that support External Network External Network Pinout With respect to signals on the NET port: • For balanced signals a “0”=low voltage i s defined as terminal A positive with respect to terminal B. • For unbalanced signal s a “0”= lo w voltage is defin[...]

TANDBERG 770/880/990 MXP 286 Cable Specification V.35 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 2 6 pi n high-density DSUB with thumbscrews. • Connectors on cable at V.35-adapte r en d: o Male 34 pin Winchester (AMP part number 2013 57 -1 or equivalent). • Cable length[...]

Appendices 287 Cable Specification V.35/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 2 6 pi n high-density DSUB with thumbscrews. • Connectors on cable at V.35-adapte r en d: o Male 34 pin Winchester (AMP part number 2013 57 -1 or equivalent) and o Male 25 pin DSUB w[...]

TANDBERG 770/880/990 MXP 288 Cable Specification RS-449 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or Equival ent • Connecto r on RS-449 : o DSUB 37 pi n Male Signal Name Female 26pin DSUB (Tandberg end) Pin Number Male 37pin DSUB (DCE[...]

Appendices 289 Cable Specification RS-449/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or Equival ent • Connecto r on RS-449 : o DSUB 37 pi n Male • Connecto r on RS-366 : o DSUB 25 pi n Male Signal Name Female 26pin DSUB (Tandb[...]

TANDBERG 770/880/990 MXP 290 Cable Specification RS-530 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or Equival ent • Connecto r on RS-530 : o DSUB 25 pi n Male • Cable length: o 1 meter Signal Name Female 26pin DSUB (Tandberg end) Pin[...]

Appendices 291 Cable Specification RS-530/RS-366 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or Equival ent • Connecto r on RS-530 : o DSUB 25 pi n Male • Connecto r on RS-366 : o DSUB 25 pi n Male • Cable length: o 1 meter Signal Name Fe[...]

TANDBERG 770/880/990 MXP 292 Cable Specification RS-449 Cable to KIV-7 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or Equival ent • Connecto r on RS-449 : o DSUB 37 pi n Male Signal Name Female 26pin DSUB (Tandberg end) Pin Number Male 37pin [...]

293 8 Glossary # 199 AV1: External input for the TANDBERG/LOEWE monitor. 2nd monitor: The second monitor of your video com munication system. The second monito r is normally placed on the right side of the first monitor. 4CIF: 4 times CIF, 704x576 pixels 4SIF: 4 times SIF, 704x480 pixels A AACLD: Advanced Audio Coding Low Delay Access code: Use Acc[...]

TANDBERG 770/880/990 MXP 294 B Bandw idth: Decides the quality of the video call. High bandwidth gives high q uality. C Call Control Data Triggered: Uses TxData, RxData and clock signals o nly. Use Data Tri ggered when no handshake sig nal is available. Call control Leased Line: Is a non-dialing protocol a nd sh ould b e used when two systems are c[...]

Glossary 295 Diagnostics: Allows testing of individual system co mponents an d displ ays the current system settings. Digital ClarityTF: Participants enjoy presentations o f ex ceptionally high quality resolution video. Disconnect site: As a Chairma n, you get the option Disco nnect site. Disconnect site allows you to disconnect any participant in [...]

TANDBERG 770/880/990 MXP 296 G G.711: Audio algorithm for normal qualit y audio (tel ephone quality, 3.1 kHz) The system will always have G.711 enabled. G.722: Audio algorithm for high quality audio (7 kHz). G.722.1: Audio algorithm for compressed high qu ality audio (7 kHz) G.728: Audio algorithm for compressed normal quality audio (telephone q ua[...]

Glossary 297 M Main Camera: Your camera. Video input 1 Max call length: This feature will automatically end both incomin g and outgoing calls when the call time exceeds the length specified. Max channels: Indicates the maximum numbe r of channels the system is allo wed to use on the E1/T1 interface. MCU: Multipoint Conference Unit. MCU stat us line[...]

TANDBERG 770/880/990 MXP 298 Non Standard Facility: The network provider may require service selection in your ISDN configuration. Valid NSF codes are from 1 to 31. 0 will disable NSF service codes. NR: Noise Reduction. Re duces constant background noise (e.g. noise from air-conditioning systems, cooling fans, etc. ). NSF: Non Standard Facility. NT[...]

Glossary 299 Request Floor: The MCU will broadcast the video in full screen to all other pa rticipants in the conference. If the MCU conf eren ce has a chai rman, a request will be sent to the the chairman. Restart: Restart s the syst e m. Restore defaults: Re stores system settings to the factory defaults. Restricted call: A call to a 56 kbps netw[...]

TANDBERG 770/880/990 MXP 300 Streaming Announcements: The system will announce to the net wo rk that it is streaming. This enables a streaming client (e.g. a PC) to co nnect to the system's streaming session. Used by Cisco IP/TV. Streaming Pass word: Prevents unauthori zed access to the stre aming fun ctionality. Streaming Source: Select betwe[...]

Glossary 301 VNC: Virtual Network Computing. Voice Switched: The active site will be displayed in full screen during a MultiSite conference. W WAVE II Camera: Wide Angle View Camera - delivers the wide st angle of view in the industry. Welcome menu: The welcome menu di splays the Menu when you are outside a call. X XGA: extended Graphi cs Array (10[...]

TANDBERG 770/880/990 MXP 302 9 Index A Access Co de......................................97, 119 Add Another Call........................................ 39 Additional mi cropho ne ............................. 231 Administrator Passwo rd ...........................137 Alert S peaker ...........................................177 Alert Tones a nd V[...]

Index 303 R Release C hair ............................................ 87 Release Fl oor ............................................ 84 Release Floor from Participant .................. 88 Request Floor ............................................ 84 Restar t ..................................................... 110 Restore de faults.............[...]