Tenda W150M+ manual

W150M + 150Mbps W ireless AP Copyright S tatement[...]

W150M + 150Mbps W ireless AP is the registered tra demark of Shenzhen T enda T echnology Co., Ltd . All the products an d product names mentioned herein are the tradem arks or registered trademarks of their respective hol ders. Copyright of the whole product a s integration, including its access o ries and software, belongs to Shenzhen T enda T ech[...]

W150M+150Mbps W ireless AP 1 Content CHAPTER 1 PRODUCT OVER VIEW .......................................... 4 1.1 Production i ntroduction .............................................................. 4 1.2 Products Features ....................................................................... 5 1.3 Package contents .............................[...]

W150M+150Mbps W ireless AP 2 6.3 MAC Address Clone ................................................................ 44 6.4 DNS Settings ............................................................................ 45 CHAPTER 7 WIRELESS SETTING ............................................ 47 7.1 Basic Settings ........................................[...]

W150M+150Mbps W ireless AP 3 12.5 Upgrade ................................................................................... 79 12.6 Reboot the Ro uter ................................................................... 79 12.7 Change Password ................................................................... 80 12.8 System Log ..................[...]

W150M+150Mbps W ireless AP 4 Chapter 1 Product overview 1.1 Production intr oduction Thank you fo r purchasing the T enda W150M+150 Mbps W ireless AP . W150M+ is a portabl e wireless AP/Router with up to 150Mbps transmission rate. It suppo rts five working modes: wireless AP (access point), Client+AP , WDS+AP , WISP Router and W ireless Router . Th[...]

W150M+150Mbps W ireless AP 5 need to configure the signal transm itter but only to s imply configure the W150 M+ to amplify the wireless signa l and multi computers can share the i nternet. This mode is mainly used in hotspot access. The fifth mode is W ireless Router mode. Us e this mode to form a local network that has b oth broadband connections[...]

W150M+150Mbps W ireless AP 6 mode, W ireless Router m ode ¾ Support 64/128 bit WEP , WP A, WP A2 encryption ¾ WPS (PBC and PIN) enabled device ¾ Provides one 10/100M bps Auto-Negotiation Et hernet port for LAN/W AN ¾ Support xDSL/Ca ble Modem, static and dynamic IP in community ne twork ¾ Support remote WEB managem ent ¾ Support wireless roam[...]

W150M+150Mbps W ireless AP 7 ¾ One Ethernet cable ¾ One USB line If any of the items do n ot match, are missing or d amaged, please contact the st ore you purchased this device from for imm ediate replacement. 1.4 LED Indicator and Port Description Front Panel and LED Indic ator Show LED indicators de scription on front panel: (From L to R) ¾ AP[...]

W150M+150Mbps W ireless AP 8 mode. ¾ WISP Router: Always blu e indicates the device in WISP Router mode. ¾ W ireless Router ： Always blue i ndicates the device i n W ireless Router mode. ¾ WPS: Blinking means the devi ce is negotiating with t he client in WPS mode. ¾ LAN/W AN: Always blue indicates the Ethernet cable is well connected and bl [...]

W150M+150Mbps W ireless AP 9 deleted and it will restore the settings t o the default one. ¾ Power: The port is for USB l ine connection. Please use the included USB line connecte d with the power adapter or the USB port of com puter . ¾ LAN/W AN: The 100Mbp s Ethernet port, in W ireless Router mode, it is a W AN access port to connect the DSL, M[...]

W150M+150Mbps W ireless AP 10 Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the bo x, please fo llow the steps below to connect the device. For bet ter wireless performance, please put the de vice in the middle of wireless coverage area. 1. Power Supply: Please use the in cluded power adapter to power on the Router [...]

W150M+150Mbps W ireless AP 11 B 、 If you use wireless network adapter to a ccess the internet, the topology dia gram is as below . W ireless network connecti on a 、 On your comput er desktop right cli ck “My Network Places” and select “Properti es”. b 、 Right c lick “W ireless Net work Connection” and s elect “V iew A vailable W[...]

W150M+150Mbps W ireless AP 12 C 、 Click “Conne ct” button.[...]

W150M+150Mbps W ireless AP 13 Chapter 3 W orking Modes Intr oduction This device h as five working m odes. Y ou can change the modes depending on the applications. This cha pter will introduce every mode in detail s. The default mode is AP (a ccess point) mode. 3.1 AP mode In this defa ult mode, th e device wo rked as a conve rter bet ween the wire[...]

W150M+150Mbps W ireless AP 14 3.2 Client+AP Mode In this mode, the device can receive the wi reless signal, meanwhile amplify the s ignal and extend the w ireless signal coverage. The wired device can receive t he sign al via the Ethernet cable. This mode is called t he wireless signal universal rep eater mode which can amplify the sour ce signal t[...]

W150M+150Mbps W ireless AP 15 3.3 WDS+AP Mode In this mode, the device can enhance the sig nal and extend th e wireless coverage. It can bridge two loc al area networks or two computers and m eanwhile amplify and transfer t he signals. The WDS+AP mode is sim ilar as WDS mode. Besides, many w ireless clients can acc ess when the device works as a br[...]

W150M+150Mbps W ireless AP 16 More details please refer to 5-3. 3.4 WISP Mode In this mode, y ou do not need to configur e the signal transm itter but only t o simply configur e the W150M+ t o amplify the w ireless signal and multi com puters can share the internet. The device supports DHCP functi on to assign IP addresses automatic ally and NA T f[...]

W150M+150Mbps W ireless AP 17 More details please refer to 5-4. 3.5 Wir eless Router Mode In this mode, the device can be wo rked as the router with wireless NA T function an d DHCP sever . The lap tops can ge t IP addresses automatically which ass igned by the DHCP sever . When the RJ45 port connects to the br oadband access, the laptops can share[...]

W150M+150Mbps W ireless AP 18 Chapter 4 How to login to the Router The chapter m ainly presents how to enter the Router’ s W eb interface. After you have finishe d the hardware installati on (Please refer to chapter2.), the fo llowing steps will assist you to set the network confi gurations for you com puter . 4.1 How to Set the W ired Network Co[...]

W150M+150Mbps W ireless AP 19 4.1.3 Select “Intern et Protocol (TCP/IP)” and click “P roperties”.[...]

W150M+150Mbps W ireless AP 20 4.1.4 Select “Using t he following IP address” a nd input the IP address. IP address: 192.168.2.XXX ： (XXX is a number from 2~254) 4.2 Login to the W eb Interface After you set y ou computer as 4.1, y ou can follow the below steps to access the Router’ s web interface. 4.2.1. T o access the Route r ’ s W eb-b[...]

W150M+150Mbps W ireless AP 21 4.2.3. If you enter th e correct user name and passwor d, you can enter the router ’ s web interface.[...]

W150M+150Mbps W ireless AP 22 Chapter 5 W orking Modes Setup Wiz ard 5.1. AP mode In this default mode, the de vice can convert the wired and wireless signal which is the center access poi nt for few clients (generally wireless network adapter). For example, in a big hotel, connect the Router to the broadband access port wit h the Ethernet cable an[...]

W150M+150Mbps W ireless AP 23 addresses autom atically . Y ou only need to co nfigure you computer to obtain IP address and DNS se ver automatically t o access the internet. (Setting wa ys refer to 4.1.) 5.2. Client+AP Log on the web-based i nterface as ch apter 4 and then configure the mode as below . 5.2.1Select “Client+AP”, click “Setup W [...]

W150M+150Mbps W ireless AP 24 connect.  MAC Address: The Router’ s physical MAC address as seen on your local networ k is unchangeable. Input the MAC address of the AP you want to connect. Som etimes, MAC address is also named BSSID. (BSSID ： Basic Service Set Identifier of wireless network. In IEEE 802.1 1, BSSID is the MAC address of wirel[...]

W150M+150Mbps W ireless AP 25  Network Mode ： Select one mode from the fol lowing. The default is 1 1b/g/n m ode. 1 1b mode ： Allow the wireless client to connect with the device in 1 1b mode at the maxim um speed of 1 1Mbps. 11 g m o d e ： Allow the 1 1g/1 1n-com pliant client device to connect with the AP at the m aximum speed of 54Mbps.[...]

W150M+150Mbps W ireless AP 26 1 1n network, select 20/40M to im prove its throughp ut. Click “Next” t o save configur ations. Note: W e suggest you do not chan ge the channel in this mode, or else you can not access the devi ce which you want to connect. 5.2.4. W ireless Security Se ttings It is suggested that yo u choose WP A-personal for “S[...]

W150M+150Mbps W ireless AP 27 Note: Make sure the device have the same Channe l, Security m ode and Extend channel as the access point. 5.3. WDS+AP Mode Setup W izard Log on the web-based i nterface as ch apter 4 and then configure the mode as below . 5.3.1. Select “ WDS+AP”, click “Set up W izard” and “Next” butt on. 5.3.2.Configure th[...]

W150M+150Mbps W ireless AP 28 as BSSID. The terminal wireless device can be an AP with WDS function or a wireless router .  Channel: Specify th e ef fective channel (from 1 to 13Auto) of the wireless n etwork. The channel you set must be the same as the term inal device.  Encrypt T ype: The encrypt type security mode you set should be the sa[...]

W150M+150Mbps W ireless AP 29 with the AP at the m aximum speed of 54Mbps. 1 1b/g mode: Allow the 1 1b/g-compliant clie nt device to connec t with the AP with a uto-negotiation speed, and 1 1n wireless client to connect the devi ce with 1 1g spee d. 1 1b/g/n mode: Allow 1 1b/g/n-com pliant client devi ce to connect with the AP w ith auto-negotiati [...]

W150M+150Mbps W ireless AP 30 After configuration complete, the AP works as a wireless signal repeater . Y ou can connect the device to com puter , satellite recei ver and IPTV set- top box and you nee d to set them to obta in IP address automatically to a ccess the source wireless device (sourc e wireless router). Detailed se ttings refer to the A[...]

W150M+150Mbps W ireless AP 31 the wireless network. Inp ut the SSID of the aimed AP .  MAC Address: The Router’ s physical MAC address as seen on your local n etwork is unchangeable. I nput the MAC address of the AP y ou want to choose. Som etimes, MAC address is also named BS SID. (BSSID ： Basic Service Set Identifier of wireless netw ork. [...]

W150M+150Mbps W ireless AP 32  Network Mode ： Select one mode from the fol lowing. The default is 1 1b/g/n m ode. 1 1b mode ： Allow the wireless client to connect with the device in 1 1b mode at the maxim um speed of 11 M b p s . 11 g m o d e ： Allow the 1 1g/1 1n-complia nt client device to connect with the AP at the maximum speed of 54Mb[...]

W150M+150Mbps W ireless AP 33 IEEE802.1 1, BSSID is the MAC address of wireless a ccess point.  Extend Channel ： T o increase data throughput of wireless network, the extension chan nel range is us ed in 1 1n mode.  Channel Bandwidth ： Select the channe l bandwidth to improve the wireless perform ance. When the networ k has 1 1b/g and 1 1[...]

W150M+150Mbps W ireless AP 34 5.5.1. Select “W ireless Router”, click “Setup W izard” and “Next” button. 5.5.2. Configure the parameters. This device s upports three kinds of access ways (ADSL virtual dial-up, dynamic IP , static IP); pl ease select the ways according to the actual sit uation. If you are not sure, you can consult local [...]

W150M+150Mbps W ireless AP 35 ¾ Sta t i c IP If your ISP provides you the S tatic IP , please select S tatic IP access way . Y ou should input the IP addr ess, Subnet Mask, Gateway , DNS sever and the secondary DNS sever provid ed by your ISP , then click “Next”. ¾ ADSL V irtual Dial-up (via PPPoE) If your ISP provides you the ADS L V irtual [...]

W150M+150Mbps W ireless AP 36 Y ou can view the status by click “S tatus Inform ation” after the device rebooted. If there s hows IP address of W AN port, you can access to the interne t. For further settings please re fer to the following chapters. 5.5.3 W ireless Basic Setting  Network Mode ： Select one mode from the following. The defau[...]

W150M+150Mbps W ireless AP 37 1 1b mode ： Allow the wireless client to connect wi th the device in 1 1b mode at the maxim um speed of 11 M b p s . 1 1g mode ： Allow t he 1 1g/1 1n-com pliant client de vice to connect with the AP at the maximum speed of 54Mbps. 1 1b/g mode: Allow th e 1 1b/g-compliant cli ent device to connect with the AP with a[...]

W150M+150Mbps W ireless AP 38 network, the extension chan nel range is us ed in 1 1n mode.  Channel Bandwidth ： Select the channe l bandwidth to improve the wireless perform ance. When the networ k has 1 1b/g and 1 1n clients, yo u can select the 40M; when it is an 1 1n network, select 20/40M to im prove its throughp ut. Click “Next” t o s[...]

W150M+150Mbps W ireless AP 39 symbols for pass phrase. Cl ick “Next” to save the configura tion. More details please refer to the following chap ter . 5.5.5. Click “A pply” to save the settings and re boot the router to let the settings take effe ct. Note: Only the computers with wireless network adapter can access to the wireless r outer i[...]

W150M+150Mbps W ireless AP 40 Chapter 6 Advanced Settings 6.1 LAN Settings This section will descr ibe how to configur e the TCP/IP parameters. 6.1.1. LAN settings in WISP and W ireless Rou ter mode  MAC Address: The device’ s physical MAC address as seen on your local network is unchange able.  IP Address: The Router’ s LAN IP addresses [...]

W150M+150Mbps W ireless AP 41  MAC Address: The device’ s physical MAC address as seen on your local network is unchange able.  IP Mode: There are two modes, Static IP and Dynamic IP . If you select S tatic IP , you nee d to input the parameters provided by your ISP . If you ch oose Dynam ic IP , you should adjust th e connection pr opertie[...]

W150M+150Mbps W ireless AP 42 parameters are also pr ovided by your ISP  Host Name: The device’ s wins name which you can us e it to visit the devic e. Notice: Once you chan ged the IP address of th e LAN port, you should use the new IP to enter into the W eb interface. 6.2 W AN Settings W AN setting is only for WISP mode and W ireless Rout er[...]

W150M+150Mbps W ireless AP 43  Password: Enter the password pro vided by your ISP .  MTU : Maximum Tr ansmission Unit. It is the size of lar gest datagram that can be sent ov er a network. The default value is 1492. Do NOT modify it unless ne cessary . But if some specific website or web appl ication so ftware can not be open or enabled, y ou[...]

W150M+150Mbps W ireless AP 44 6.2.2 St at i c I P If your connection m ode is static IP , you can modify th e following addressing inform ation.  IP Address: Here enter the W AN IP address provid ed by your ISP . If yo u are not clear , consult you ISP please.  Subnet Mask: Ent er the subnet m ask provided by your ISP . Generally , it is 255.[...]

W150M+150Mbps W ireless AP 45 Some ISPs require end-user' s MAC address binding to access t heir network. ISP will provide a vali d MAC address and you should input MAC address an d save the configura tion.  MAC Address: The MAC address to be regist ered with your Internet service provider .  Clone MAC Addr ess: Register your PC's M[...]

W150M+150Mbps W ireless AP 46  DNS Settings: Click the checkbox to enable the DNS s erver . The Router ’ s DHCP sever will answer the client’ s requests and distribute D NS address.  Primary DNS Address: Enter the neces sary address provided by your ISP .  Secondary DNS Addr ess: Enter the second address if your ISP provides, w hich is[...]

W150M+150Mbps W ireless AP 47 Chapter 7 W ir eless Setting 7.1 Basic Settings  Enable Wir eless: Check to enable the Rout er ’ s wireless features; uncheck to dis able it.  Network Mode ： Select one mode fro m the following. The default is 1 1b/g/n m ode. 1 1b mode ： Allow the wireless client to connect with the device in 1 1b mode at t[...]

W150M+150Mbps W ireless AP 48 54Mbps. 1 1 b/g mode: Allow the 1 1b/g-com pliant client device to connect with the AP with auto-negotiation speed, and 1 1n wireless client to connect the device with 1 1g speed. 1 1b/g/n mode: Allow the 1 1b/g/n-com pliant client dev ice to connect with the AP with auto-negotiation speed.  SSID ： SSID (Service S[...]

W150M+150Mbps W ireless AP 49 7.2 Wir eless Security Setting It is used to config ure the AP network’ s security setting. Here presents the comm on encryp tion methods , including WP A-personal, WP A2-personal, W AP/W AP2-Personla, Mixed WEP , Open, Shared. It is suggested you choose WP A-personal for “Security Mode” and AES for “WP A Algor[...]

W150M+150Mbps W ireless AP 50 ¾ WP A Algorithms ： Provides TKIP [T emporal Key Integrity Protocol] or AES [Advanced Encryption S tandard]. ¾ Pass Phrase: Enter the encrypted characte rs with 8-63 ASCII characters. ¾ Key Renewal Interval Set the key’ s renewal period. ： 7.2.2 WP A2-personal WP A2 (W i-Fi Protected Access version 2) provides[...]

W150M+150Mbps W ireless AP 51  WP A Algorithms ： Provides TKIP [T emporal Key I ntegrity Protocol] or AES [Advanced Encryption S tandard].  Pass Phrase: Enter the encrypted characte rs with 8-63 ASCII characters.  Key Renewal Interval Set the key’ s renewal period. ： 7.2.3 Mixed WEP WEP (W ired Equivalent Privacy), a basic encryption[...]

W150M+150Mbps W ireless AP 52  SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop- down menu.  Security Mode: From the drop-dow n menu select the corresponding security encryption modes.  WEP Key: Set the WEP key with the form at of ASCII or Hex.  Key Explanation: Y ou can enter ASCII code (5 [...]

W150M+150Mbps W ireless AP 53  BG protection Mode: Auto by default. It is for 1 1b/g wir eless client to co nnect 1 1n wireless network sm oothly in a complicated wireless area.  Basic Data Rates: For diff erent requirement, you c an select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.-1 1Mbps…). It is recom mended [...]

W150M+150Mbps W ireless AP 54 parameter controls what size data pa cket the frequency protocol issues to R TS packet. The default value of the attribute is 2346. It is recommended not to m odify this value in SOHO environment.  TX Power: Set the output power of wireless radio. The default value i s 100.  WMM Capable: It will enhance the data [...]

W150M+150Mbps W ireless AP 55  WPS settings ： T o enable or disable WPS function. The default is “disable”.  WPS mode: PBC (Push-Button Configu ration) and PIN code.  PBC ： Select the PBC or press the WPS butto n on the back panel of the device for about on e second (Press the butto n for about one second and WPS ind icator will be[...]

W150M+150Mbps W ireless AP 56 key and other information.  WPS Current S tatus ： Idle means WPS in idle state. S tart MSC process means the process ha s been starte d and waits for being connecte d. Configured m eans the negotiation is successful between server and clients.  WPS Configured ： “yes” means WPS feature is enabled and goes [...]

W150M+150Mbps W ireless AP 57  MAC Address Filter ： Allow/Block MAC address filter . Select “of f” to mal-function MAC a ddress; “Block” to prevent the MAC address es in the list from accessing the wireless network; “All ow” to allow the MAC address in the list to access the wire less network.  MAC Address Management ： Input t[...]

W150M+150Mbps W ireless AP 58  MAC Address ： Shows current MAC addresses of th e hosts connecting to the Router .  Bandwidth ： Shows current frequency bandwidth the wireless client used.[...]

W150M+150Mbps W ireless AP 59 Chapter 8 DHCP Server DHCP server is for the WISP mode and wireless Router mode. 8.1 DHCP Settings DHCP (Dynamic Host Co ntrol Protocol) is to assign an IP address to the com puters on the LAN /private network. Whe n you enable the DHCP Server , the DHCP Server will allocate au tomatically an unused IP address from the[...]

W150M+150Mbps W ireless AP 60  Lease Time: The length of the IP address lease. Set an appropriate le ase time to improve the recovery ef ficiency of invalid IP address. For example ： If the lease tim e is an hour , then DHCP server will reclaim the IP address each hour . 8.2 DHCP List and Binding DHCP client can display computers’ IP address[...]

W150M+150Mbps W ireless AP 61  IP Address: Enter the IP address which needs to be boun d.  MAC Address: Enter the MAC address o f the computer you want to assign the abov e IP address. Click “Add” to a dd the entry in the lis t.  Hostname: The name of the c omputer which is a dded a new IP address.  Lease T ime: The left time le ngt[...]

W150M+150Mbps W ireless AP 62 Chapter 9 V irtual Server V irtual Server feature is only for wireless signal amplifi cation mode and the wireless Router mode. 9.1 Port Range Forwarding This section deals with the port range forwarding mainly . The Port Range Forwarding a llows you to set up a range of publi c services such as web servers, ftp, e- ma[...]

W150M+150Mbps W ireless AP 63 set the applica tions.  Protocol: Select the pro tocol (TCP/UDP/Both) for the application.  Enable: Click to check it for correspondi ng operation.  Delete: Click to c lear the parameters.  W ell-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to a dd to the configured[...]

W150M+150Mbps W ireless AP 64  DMZ Host IP Address: The IP address of the computer you want to expos e.  Enable: Click it to en able the DMZ host. For example: Set the computer at the IP address of 192.168.2.100 in LAN as a DMZ Host to intercom municate with anot her host on the Internet. IMPOR T ANT: When the DMZ host is enabled, the firewal[...]

W150M+150Mbps W ireless AP 65  Enable UPnP: Click the ch eckbox to enable th e UPnP .[...]

W150M+150Mbps W ireless AP 66 Chapter 10 Security Settings The security settings are for WISP mode and W ireless Router mode. 10.1 Client Filter Settings T o facilitate your further management to online b ehavior of the computers in LAN, you can ena ble client filter t o control som e ports access to Internet.  Client filter: Select it to e nabl[...]

W150M+150Mbps W ireless AP 67  Policy Name: Enter a nam e for the access policy selected.  IP S tart/End: Enter the starting/ending IP address.  Port: Enter the port range based over the protocol for access policy .  Ty p e : Select one pr otocol (TCP/UDP/Bot h) from the drop-down menu.  Tim e s: Select the tim e range of client filt[...]

W150M+150Mbps W ireless AP 68 ¾ URL Filter: Check to enable URL filter . ¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access pol icy . ¾ Filter Mode: Click o ne radio button to enab le or disable to access the Internet. ¾ Policy Name: Enter a nam e for the access policy selected. ¾ S tart/End IP: E[...]

W150M+150Mbps W ireless AP 69 access the Internet from 9 ： 00 to 18 ： 00 everyday and on ly can search the WEB pages contain the strings such as si na, sohu, and yahoo; you need to set the packe t filtering list as the above dia gram. (Notice: diff erent strings need to be apart by a com ma.) 10.3 MAC Address Filter In order to manage th e comp[...]

W150M+150Mbps W ireless AP 70 only to the c orresponding MAC addr ess.  Policy Name: Enter a nam e for the access policy selected.  MAC Address: Enter the MAC address of the computer you want to run the access policy .  Tim e s: Select the tim e range of client filter .  Date: Select the day(s) to run the access poli cy .  Apply: Sel[...]

W150M+150Mbps W ireless AP 71 10.5 Remote WEB Management This section is to allow the network adminis trator to manage the Router remotely . If you want to access the Router from outside of the local network, please select the “Enable”.  Enable: Check t o enable remote web m anagement.  Port: T he management port open to outside ac cess. [...]

W150M+150Mbps W ireless AP 72 For example: If you want to configure the IP address 218.88.93. 33 to access the device’ s web interface, please set it as above. 10.6 W AN Ping The ping test is t o check the status of y our internet connectio n. When disabling the test, the system will ignore the ping test from W AN.  Ignore the Ping from W AN: [...]

W150M+150Mbps W ireless AP 73 Chapter 1 1 Routing setting 1 1 .1 Routing T able This page shows the primary routin g table. The main duty for a router is to look for a bes t path for every data frame, and transfer this d ata frame to the destinat ion. So, it’ s essenti al for the router to choose the b est pat h, i.e. ro uting arithmetic. In orde[...]

W150M+150Mbps W ireless AP 74 Chapter 12 System Tools 12.1 Tim e Settings This section is to select the tim e zone for your locati on. If you turn off the Router , the sett ings for time disappear . However , the R outer will automatic ally obtain the GMT time again once it has access to the Internet.  T ime Zone: Selec t your time zone from the[...]

W150M+150Mbps W ireless AP 75 The DDNS (Dynamic Domain Na me System) is suppo rted in WISP mode and W ireless Router mode. It is to assign a fixed host and domain nam e to a dynamic Internet I P address, which is used to monitor hosti ng website, FTP server and so on behin d the Router . If you want to activate this function, please s elect “Enab[...]

W150M+150Mbps W ireless AP 76  Domain Name: Enter the domain name which is optional. User name tenda Password 123456 Domain nam e tenda.3322.or g After mapping the port in the virtual server , setting account information in DDNS server and in the add ress field entering http://tenda. 3322.or g, you can access the W eb page. 12.3 Backup/Restore S[...]

W150M+150Mbps W ireless AP 77 Click “Save” t o save the configuratio n files. ¾ Restore Setting ： Click “Browse” button to select the backup files. Click “Restore” b utton to restore previous sett ings.[...]

W150M+150Mbps W ireless AP 78 12.4 Restor e to Factory Default Setting This button is to reset all sett ings to the defaul t values. It m eans the Router will lose all the settings you have set. So please Note down the related settings if necessary .  Restore: Click this b utton to restore to defa ult settings.  Factory Default Settings: User[...]

W150M+150Mbps W ireless AP 79 12.5 Upgrade The Router provides the firmware upgrade by clic king the “Upgrade” after browsi ng the firmware upgrade packet which you can download from www .tenda.cn . ¾ Browse: click this button to selec t the upgrade file. ¾ Upgrade: clic k this button to start the upgrading process. After the upgrade is compl[...]

W150M+150Mbps W ireless AP 80 Reboot the router: Cl ick this button to reboot the device . 12.7 Change Password This section is to se t a new user name and passw ord to better secure your router and n etwork. ¾ User Name: Enter a n ew user name for the de vice. ¾ Old Password: Enter the ol d password. ¾ New Password: Enter a new password. ¾ Re-[...]

W150M+150Mbps W ireless AP 81 12.8 System Log The section is to view t he system log. Click the “R efresh” to update th e log. Click “Clear” to cl ear all sho wn informati on. If the log is over 150 rec ords, it will clear t hem automatically . ¾ Refresh: Click this b utton to update t he log. ¾ Clear: Click this button to clear the curre[...]

W150M+150Mbps W ireless AP 82 Appendix Ⅰ : How to “Obtain an IP Automatically” If you enable DHCP (default), you can get the IP address, Gateway , DNS automatically to access the internet. Please set you device as below . 1. On your computer deskt op right click “My Network Places” and select “Properties” . 2. Right click “Local Are[...]

W150M+150Mbps W ireless AP 83 3. Select “Inter net Protocol (TCP/IP)” and clic k “Properties”. 4. Select “Obt ain an IP address autom atically”[...]

W150M+150Mbps W ireless AP 84 5. Select “S tatus” within “ Local Area Connection” – clic k "support "dialog box, y ou can see wheth er you have got the IP .[...]

W150M+150Mbps W ireless AP 85 Appendix : How to set the network card Ⅱ after device encrypted When the device is e ncrypted, you need to e nter password to connect to the wireless device to acces s the internet. Set up a wireless network adapter as follows: 1. On your computer desktop ri ght click “My Network Places” a nd select “Properties[...]

W150M+150Mbps W ireless AP 86 3. Select “T enda” and click “Conne ct” or double-cl ick “T enda”, input the “N etwork key” and “Confirm network key” to connect the Router . 4. “Connected” will be shown in the interface as t he following diagram.[...]

W150M+150Mbps W ireless AP 87 Appendix Glossary Ⅲ Channel An instance of m edium use for the purpose of passing protocol data units (P DU) that may be used simultane ously , in the same volume of space, with other instances of medium use(on other channels) by other i nstances of the sam e physical layer (PHY ),with an acceptably low frame erro r [...]

W150M+150Mbps W ireless AP 88 encryption. There are 2 methods for entering the K EY ; one is to enter a 16-bit HEX digit. Using this method, users m ust enter a 10-digit num ber (for 64-bit) or 26-digit number (for 128-bit) in th e KEY field. Users must select t he same key number for all devices. The other method is to enter a text and let the com[...]

W150M+150Mbps W ireless AP 89 Appendix : Ⅳ Troubleshooting In this part some questi ons and problems shown duri ng the Router ’ s usage and installation wil l be given suggesti ng answers. If your problems are not in the l ist, please log i nto our website www .tenda.cn or send an E-mail to suppor t@tenda.cn, and we will reply you in th e earli[...]

W150M+150Mbps W ireless AP 90 conflict. W hat can I do? Check if there are other DHCP servers in the LAN. If there have, disable them . The default IP address of the Router is 192.168 .2.1 and please maker sure the address is not occ upied by other devices. If there are two computers wit h the same IP addresses, please modify one. 4. My computer ca[...]

W150M+150Mbps W ireless AP 91 W AN MAC address to the bind21ing PC’ s MAC address. Select “MAC Address Clone” i n “Advanced Setting” to input your computer’ s MAC address and cl ick “Apply” to act ivate it. 7. How to share m y computer ’ s source wit h other users in Internet ？ If you want Internet users to access the interna l [...]

W150M+150Mbps W ireless AP 92 Server Protocol Service Port WEB Server TCP 80 FTP Server TCP 21 T elnet TCP 23 NetMeeting TCP 1503 、 1720 MSN Messenger TCP/UDP File Send:6891-6900(TCP) V oice:1863 、 6901(TCP) V oice:1863 、 5190(UDP) PPTP VPN TCP 1723 Iphone5.0 TCP 22555 SMTP TCP 25 POP3 TCP 1 10 8. W hy can’t I use wireless W AN function to [...]

W150M+150Mbps W ireless AP 93 different as the one obtained at LAN port. If they are at the same range, you can m odify the LAN IP addre ss to solve the problem . d. Please do not detach any antenna of th e wireless Router when you are using the Router . After trying all the above steps, if you still ca n’t access t he Internet , you can cont act[...]

W150M+150Mbps W ireless AP 94 Add: A12E,The first world squar e,7002,Hongli west road,Futian,Shenzhen Te l : (+86)755-25312445 253124 42 83737333 (extensi on no. 8310 or 8318) Fax: (+86)755-2 7057244 E-mail: sales@tendab x.com USA Branch: Add: 6955 N. Durango Dr ., Suite 1 1 15-10, Las V egas, NV 89149, U.S.A. Te l : +1 (702) 483 5366 Email: biz@te[...]

W150M+150Mbps W ireless AP 95 District, Ha Noi, V iet Nam Te l : 0084-097-9955-122 Email: sales@tenda.com .cn SHENZHEN TENDA TECHNOLOGY CO., LTD www .tenda.cn[...]

W150M+150Mbps W ireless AP 96 Appendix Ⅴ Regulatory Information EU Declaration or Declaration of Conformity Hereby , SHENZHEN TENDA TECHNOLOGY C O. ,L TD, declares that th is Wireles s Broadband Ro uter is in c ompliance with the esse ntial req uiremen ts and ot her relev ant provis ions of Directive 1999/5/EC. FCC Statement This equipment has be[...]

W150M+150Mbps W ireless AP 97 -Consult the dealer or an experienced radio/TV technician for help. T o assure conti nued compliance, any changes or modifications not expressly approved by the party responsible for compl iance could void the user’s authority to operate this equipment. (Example- use only shie lded int erface cable s when conne cting[...]