Toshiba L305 manual

Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual Toshiba Personal Computer Satellite L300/L305 Satellite Pro L300 EQUIUM L300 SATEGO L300 (PSLB0x/PSLB1x) (PSLB2x/PSLB3x) Maintenance Manual TOSHIBA CORPORATION S/ No[...]

ii Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Copyright © 2008 by Toshiba Corporation. All rights reserv ed. Under the copyright laws, this manual cannot be reproduced in any form without the pr ior written perm ission of Toshiba. No patent liability is assumed with respect to the use of the inform ation cont[...]

Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite L300/ L305 / Satellite Pro L300 / EQUIUM L300 / SATEGO L300, referred to as Satellite L300/ L305 / Satellite Pro L300 / EQUIUM L300 / [...]

iv Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite L300/L305 / Satellite Pro L300 / EQUIUM L300 / SATEGO L300 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU pr[...]

Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual v Conventions This manual uses the following form ats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For ex[...]

vi Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Table of Contents Chapter 1 Hardware Overview 1.1 Features ......................................................................................................... .............2 1.2 System Unit Components ..........................................................[...]

Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual vii Procedure 3 Format Check................................................................................ 2-12 Procedure 4 Test Program Check ..................................................................... 2-13 Procedure 5 Connector Check and Replacement Chec[...]

viii Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 3.2.5 Audio Record Test .................................................................................8 3.2.6 DMI Read ...............................................................................................8 3.2.7 DMI Write ............................[...]

Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual ix Before You Begin .............................................................................................. 4-4 Disassembly Procedures .................................................................................... 4-5 Assembly Procedures .................[...]

x Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Installing the Wireless LAN Card ................................................................... 4-27 4.7 Top Cover ............................................................................................................. 4-28 Removing the Top Cover ........[...]

Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual xi Installing the CCD and MIC ............................................................................ 4-53 4.17 Speakers ............................................................................................................... 4-5 4 Removing the Speakers...[...]

xii Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 Appendix C Pi[...]

Chapter 1 Hardware Overview[...]

1 Hardware Overview ii Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual iii Chapter 1 Contents 1.1 Features ................................................................................................................... ............ 2 1.2 System Unit Components .....................................................[...]

1 Hardware Overview iv Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Figures Figure 1-1 ID Parts Description Placement ............................................................................... 6 Figure 1-2 Computer Block Diagram ...............................................................................[...]

1 Hardware Overview 1.1 Features 2 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 1.1 Features The Toshiba Satellite L300/L305/Satellite Pr o L300/EQUIUM L300/SATEGO L300 is a full size notebook PC based on the mobile Intel Core2 Duo, Dual Core and Merom Celeron Processors, providing high-speed processing capab il[...]

1.1 Features 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 3 The computer has two SO-DIMM slots, which come standard with DDRII-667MHz module. It supports PC2-5300 and uses SO-DIMMs (DDRII SDRAM) driven at 1.8V, accepting BTO/CTO for your memory requirem ent s. It can incorporate up to 4.0GB [...]

1 Hardware Overview 1.1 Features 4 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual y 15.4” WXGA Non-CSV 200nits display  Keyboard The keyboard has 30 kinds’ countries keyboard.  Battery The computer has a removable 3/6/9 Cell Lith ium Ion battery pack and an internal RTC battery (rechargeable).  Univer[...]

1.1 Features 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 5  On-Board LAN The internal LAN supports 10/100Mbit, enabli ng connection to a LAN at up to 100Mbps. It supports Wake-up on LAN from S3/S4/S5 and PXE boot support. This internal LAN has RJ45 jack with signal reception LED to direc[...]

1 Hardware Overview 1.1 Features  Figures 1-1/1-2/1-3 and 1-4 show the com puter and its system unit configuration, respectively. Figure 1-1 ID Parts Description Placement 6 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

1.1 Features 1 Hardware Overview Figure 1-2 Computer Block Diagram Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 7[...]

1 Hardware Overview 1.1 Features Figure 1-3 System Board Configurations 8 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

[...]

1.2 System Unit Components 1 Hardware Overview 1.2 System Unit Components Figure 1-4 is Block Diagram of the System Unit. Figure 1-4 System Unit Block Diagram Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 9[...]

1 Hardware Overview 1.2 System Unit Components 10 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual The system unit of the computer consists of the following com ponents:  Processor: Intel Core2 Duo, Dual Core & Merom Celeron Processor. y Penryn Core2 Due Processor (FSB, 800MHz) − Core Speed: 2.2/2.4/2.5/2.6[...]

1.2 System Unit Components 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 11 y 8Mb x 1 chip (1024KB flash parts) − NvStorage Size: 128KB − NvStorage Free Space: 101KB − FV00 Size: 624KB − FV00 Free Space: 50KB − FV01 Size: 64KB − FV01 Free Space: 45KB − FV02 Size: 36KB − FV02 F[...]

1 Hardware Overview 1.2 System Unit Components 12 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual − Enhanced Power Management − Manageability − System Management Bus (SMBus 2.0) − Intel High Definition Audio Controller − Integrated FAN Speed Control  Card Bus Controller y RICOH R5C804 − PCMCIA Slot C[...]

1.2 System Unit Components 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 13 − Universal I/O port − Battery capacity check − Flash memory reprogram ming function − EC access interface − I2C communication control  Battery EEPROM y 24C02 equivalent (128 words x 16 bits, I2C interfac[...]

1 Hardware Overview 1.2 System Unit Components 14 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual  Wireless LAN Controller y Support following 3 kinds of mini PCI wireless LAN cards − IEEE 802.11g − IEEE 802.11ag − IEEE 802.11agn y Data Rate − IEEE 802.11g: Standard 54M bps − IEEE 802.11ag: Standard 54[...]

1.3 2.5-inch HDD 1 Hardware Overview 1.3 2.5-inch HDD The computer contains an extremely low-pr ofile, lightweight and high-perform ance HDD. The HDD incorporates 9.5 mm or 12.5 m m height magnetic disk and m ini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 80, 120, 160, 200, 250, 300, 3[...]

1 Hardware Overview 1.4 Combo CD-RW/DVD-ROM 1.4 Combo CD-RW/DVD-ROM The Combo CD-RW/DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and HS CD-RW at 10x speed and US CD-RW at 24x speed and CD-RW at 4x speed. The Combo CD-[...]

1.5 DVD Super Multi (+-R Double Layer) 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 17 1.5 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-in ch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and[...]

1 Hardware Overview 1.6 HDD DVD ROM 18 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 1.6 HD DVD ROM The HD DVD ROM drive accepts 12-cm (4.72-inch ) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read HD DVD ROM at 1x speed, CD- ROM at 24x speed, and write CD-R at 16x sp eed, C[...]

1.7 Power Supply 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 19 1.7 Power Supply The power supply unit provides many different voltages for the system board and perform s the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the co[...]

1 Hardware Overview 1.8 Batteries 20 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 1.8 Batteries The computer has the following four types of batteries:  Main Battery Pack  Real Time Clock (RTC) Battery Table 1-5 lists the specifications of these batteries. Table 1-5 Battery Specifications Battery Type Mate[...]

1.8 Batteries 1 Hardware Overview Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual 21 Table 1-6 Quick/Normal Charging Time State Charge Time Off-State Charge 3/6/9 Cell About 4 hours max On-State Charge 3/6/9 Cell About 4~10 hours max NOTE: The time required for normal charge depends on the power consumption by the[...]

2 Troubleshooting 2-i Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2  Chapter 2 Troubleshooting[...]

2 Troubleshooting 2-ii Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual Chapter 2 Contents 2.1 Outline .................................................................................................................... 2-1 2.2 Basic Flowchart ......................................................................[...]

2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-iii 2.10 Audio Test ............................................................................................................ 2-22 Procedure 1 Test Program Check ................................................................. 2-22 Procedure[...]

2 Troubleshooting 2-iv Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual Figures Figure 2-1 Basic Flowchart ............................................................................................. 2-3 Tables Table 2-1 HDD Error Code and Status ..................................................................[...]

2.1 Outline 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-1 2.1 Outline This chapter describes the fault diagnosis proced ures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System board 2. HDD 3. Keyboard 4. Display 5. ODD drive 6. LAN 7. Speak[...]

2 Troubleshooting 2.2 Basic Flowchart 2-2 S a tellite L300/L305/Satellite Pro L300/EQUIUM L3 00 /SATEGO L300 Maintenance Manua l 2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flow chart steps, verify the following:  Ask the user if a password has[...]

2.2 Basic Flowchart 2 Troubleshooting Star t Connect the AC Adapter DC IN LED on ?? BATTERY LED on ?? Turn the power on. Any error message displayed ?? Message "In Touch with Tomorrow Toshiba" displayed Follow the power supply diagnostic p rocedure in Section 2.3 Follow the power supply diagnostic p rocedure in Section 2.3 Follow the syst[...]

2 Troubleshooting 2.2 Basic Flowchart Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6 N o 1 Insert Bootable CD into ODD Diagnostic Program Loaded ?? Perform each test with the diagnostic program. Any error detected by the diagnostic program ?? Perform the continuous test to check if the error is intermittent. Follow t[...]

2.2 Basic Flowchart 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-5 If the diagnostic program cannot detect an e rror, the erro r may be interm ittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detect[...]

2 Troubleshooting 2.3 Power Supply 2-6 S a tellite L300/L305/Satellite Pro L300/EQUIUM L3 00 /SATEGO L300 Maintenance Manua l 2.3 Power Supply The power supply in the computer controls ma ny functions and com ponents. To check if the power supply is defective or malfunctioning, fo llow the troubleshooting procedures below as instructed. Procedure 1[...]

2.3 Power Supply 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-7  DC IN LED DC IN LED Power supply status On in Green DC power being supplied (from the AC a dapter) Off Battery damage and can’t charge d uri ng DC-in. Off Else If the DC IN LED off, follow the steps below: 1. Remove the [...]

2 Troubleshooting 2.3 Power Supply Procedure 2 Connection Check Power is supplied to the system board as illustrated below: AC adaptor System board AC power cord AC adaptor cord Battery pack Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugge[...]

2.4 System Board 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-9 2.4 System Board To check if the system board is defectiv e or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check P[...]

2 Troubleshooting 2.4 System Board 2-10 Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual[...]

2.4 System Board 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-11 Procedure 2 Test Program Check The maintenance test program contains seve ral program s for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test [...]

2 Troubleshooting 2.5 2.5-inch HDD 2-12 Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2.5 2.5-inch HDD To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Pr[...]

2.5 2.5-inch HDD 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-13 create a DOS partition on drive C. Then restart the computer. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return t[...]

2 Troubleshooting 2.5 2.5-inch HDD Procedure 4 Test Program Check Run the HDD test program stored on the maintenance test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status name s are list[...]

2.5 2.5-inch HDD 2 Troubleshooting Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Di sassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connectors have been firmly connected to the HDD, system board and CPU. HDD System board CP[...]

2 Troubleshooting 2.7 Keyboard 2.6 Keyboard To check if the computer’s keyboard is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Keyboard test availabl e as part of the maintenance t[...]

2.7 Display 2 Troubleshooting 2.7 Display To check if the computer’s display is def ective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 External Monitor Check Connect an external monitor [...]

2 Troubleshooting 2.7 Display Check 3 The FL may be fault y. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. Check 4 The FL inverter board may be fa ulty. Replace it w ith a new one and return to Procedure 3. If there is still an error, perform Check 5. Check 5 Make sure the LCD/FL cable has been fi[...]

2.8 ODD Drive 2 Troubleshooting 2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is def ective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 ODD Cleaning Check 1. Turn off the pow[...]

2 Troubleshooting 2.8 ODD Drive 2-20 Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual Check 3 The ODD drive may be faulty. Replace the ODD drive with a new on following the steps in Chapter 4. If the ODD drive is st ill not functioning properly, perform Check 4. e , Check 4 The system board m ay be faulty. Replac[...]

2.12 LAN 2 Troubleshooting Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual 2-21 2.9 LAN To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Pr[...]

2 Troubleshooting Error! Reference source not found.Audio Test 2.10 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Audio test availabl[...]

2.11 2 Troubleshooting Cooling Module 2.11 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check Procedure 1 Test Program Check Execute the Fan On/off test program available[...]

2 Troubleshooting 2.11 Cooling Module 2-24 Satellite L300/L305/Sa tellite Pro L300/EQUIUM L3 00/SATEGO L300 Maintenan ce Manual[...]

Chapter 3 Diagnostic Programs[...]

3 Diagnostic Programs ii Satellite L300,Satellite Pro L300, EQUIUM L300,SATEGO L300 Main tenance Manual Chapter 3 Contents 3.1 General .......................................................................................................................... 1 3.2 Quick Start ..........................................................................[...]

3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual iii 3.9 Communication (COMM) .......................................................................................... 55 3.10 Peripheral .............................................................................................................[...]

[...]

3.1 General 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 1 3.1 General This chapter explains the dia gnostic programs which tests and di agnoses the functions of the hardware components of this computer. The di agnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NO[...]

3 Diagnostic Programs 3.1 General 2 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual  A Test Media CD (A-BEX TEST CD-R OM TCDR-702)(for CD-ROM test)  A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1)  An External Monitor (for DISPLAY test)  A CD-ROM Driver (for CD-ROM test)  Audio Line for audio re[...]

3.2 Quick Start 3 Diagnostic Programs 3.2 Quick Start When the system is booting from Service Diagnos tic CD, the following screen will be displayed: Please select a test item or select 0 to exit to Free -DOS: 3.2.1 Quick Test When this item is selected, the syste m will run the configured test item s and generate a test report automatically. When [...]

3 Diagnostic Programs 3.2 Quick Start Select ‘Test Mouse’ or press F8 to run the test. The prompt inform ation would be displayed in the screen as below. This test item needs user to verify whether th e mouse works normally. The test result will be displayed in the f ollowing screen: 4 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300[...]

3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highl ight a test item by us ing arrow keys, then, press Enter to start. If there are parameters pr ovided, user should set para meters in the parameter dialog window. CPU Speed Test (Step by Step): 1. Select test item: Select System — CPU — CPU Speed , then, press th[...]

3 Diagnostic Programs 3.2 Quick Start 3. Test Result System will automatically run and display the tes t result as follows: Following is the comparison report of the two testing methods m entioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the para[...]

3.2 Quick Start 3 Diagnostic Programs As to the method adopted in CPU Speed test , user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time. 3.2.3 Keyboard Layout test The test purpose is to che[...]

3 Diagnostic Programs 3.2 Quick Start It requires user to press the key and ch eck whether the key in the screen changes color or not. User can terminate test by typing ‘ END ’. When testing the ‘ Fn ’ key, it must press the ‘ Esc ’ key at the same time. When the user has checked all the keys and all the keys in the screen have changed [...]

3.2 Quick Start 3 Diagnostic Programs User can press any key to exit the program. 3.2.7 DMI Write In addition to reading the DMI information, DMI Write also permits a ttributes editing and updating: Manufacture, Product Name, Ve rsion, Serial Number, and OEM Part Number, etc. The following screen will be d isplayed: In this screen, All lines which [...]

3 Diagnostic Programs 3.2 Quick Start During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI W rite. The confirmation screen is as below: NOTE: Setup All of DMI Informati on in Type is Max 32 Digital The attributes that have been modified woul d be mar[...]

3.2 Quick Start 3 Diagnostic Programs On the left column of the above screen, the detected hardware components are listed. The corresponding information of th e detected hardware components is displayed on the right of the screen. It displays the current running status information of the check program. The name of the program is marked on the t op [...]

3 Diagnostic Programs 3.2 Quick Start 3.2.9 View Logs User can enter one choice to view a log file in the screen as follows. 3.2.10 Exit to Free DOS Select this item to exit to Free DOS. 3.2.11 The Diagnostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progr[...]

3.2 Quick Start 3 Diagnostic Programs 1. Diagnostics Windows When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There would prompt a message box called USER BRE AK in the central of the window whether user press ESC to inter[...]

3 Diagnostic Programs 3.2 Quick Start  SKIP ---- Stop the sub-item of current test item to go to the next item ’s test;  ABORT ----Stop the current test item to test the next m odule.  ABORT ALL ---- Stop all the selected test ite ms. User could use the hot key Ctrl+D to achieve the same operation. When the user calls ABORT ALL, the foll[...]

3.2 Quick Start 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 15  Remaining Battery Capacity : Remaining Battery Capacity detected in the curren t Battery, e.g. ‘BAT: 46%’;  Test Order : Define the test sequence. There is two sequence modes: Sequential Test Mode and Random Test Mode.[...]

3 Diagnostic Programs 3.3Option 3.3 Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s param eters and t hose parameters created by the L OG file. Options Menu Notes: • Select All/None Items Switch between selecting a ll test items and selecting none. T he hot key is F6 . ?[...]

3.3 Option 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 17 Configure batch parameters and a ll the test item’s param eters . • Load Batch Parameters Upload all the test items and the param eters to the *.ini file. • Save Batch Parameters Save all the parameters and the test item s that [...]

3 Diagnostic Programs 3.3Option • Test Order Specify the order of the test items. C hoose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. • Test Options Choose one of the following options: 9 Wait On Error Wait for further confirmation while an error occurs. 9 Break On Error[...]

3.3 Option 3 Diagnostic Programs Monitor the remaining ba ttery capacity (percent). 9 Monitor CPU Thermal Monitor the CPU temperature. • Test Mode 9 LOOPBOUND The chosen test items will run repeated ly accord ing to the times specified in the 'Number of Loops'. 9 TIMEBOUND The chosen test items will run for an exte nt tim e specified in[...]

3 Diagnostic Programs 3.3Option Repeat times of the test item. • Interactive If the item is enabled during the test, the te s t items that need user to response can run normally, such as PS2 Mouse te st; If it is disabled, thos e test item s will report FAIL. Whether the option here is enabled, it only affects the current test item. • Parameter[...]

3.3 Option 3 Diagnostic Programs In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files. Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 21[...]

3 Diagnostic Programs 3.3Option 3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service DiagnosticsOptions - Generate Report. • Report Destination If selecting 'NONE', no log file will be generated; if selecting 'F ILE', a log file with the name specified in 'Log File Name' will be gene[...]

3.3 Option 3 Diagnostic Programs If selecting this parameter, erro rs and time will be recorded only when the test fails. 9 Append to Old Log File If selecting this parameter, the new lo g will be added to the old one. 9 Log Device Info on Fail If selecting this parameter, deta ils of the failed test will be reco rded. • Log file Name Specify the[...]

3 Diagnostic Programs 3.3Option In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: • ↑ , ↓ Scroll a line backward or forward on the screen. • Page Up, Page Down 24 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Man[...]

3.3 Option 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 25 Scroll a page backward or forward on the screen. • Esc Exit the Log viewer. • F1 Display the Help information about the Log viewer operations and the functional keys. • Ctrl+Home Go to the start of the log file. • Ctrl+End Go [...]

3 Diagnostic Programs 3.3Option 26 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual Base Memory Test : PASS Extended Memory Test : PASS End Time: Wed Jul 05 10:47:51 2006 <Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10 [MSTPad] Begin Time: Wed Jul 05 10:48:54 2006 Touch Pad Test :[...]

3.4 Subtests 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 27 3.4 Subtests Test Group Sub Item ID Subtest Test ID Test items Internal Name System 01 CPU 01 Basic Functionality Test [CPUBasicFun] 02 CPU Speed [CPUSpeed] 03 Coprocessor NPU Basic Functions NPU Interrupt Coprocessor [NPUFun ] [NPU[...]

3 Diagnostic Programs 3.4 Subtests 28 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 02 Random Increment Read/Write [RandIncr] 11 Data Bus Test [DataBus] 12 Memory Speed Test [MemSpeed] Storage 01 HDD 01 Sequential/Random R/W [SeqRdRW1] 02 Sequential/Random Seek [Seek1] 03 Performance [Perform1] 04 Controller Check [...]

3.4 Subtests 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 29 VESA 1024x768x32 K Mode VESA 1024 x 768 x 16 K Mode VESA 1024 x 768 x32bit Mode [V1024768_32] 04 1 280 X 800 Video Modes VESA 1 280 x 800 x256 Mode VESA 1 280 x 800 x64K Mode VESA 1 280 x 800 x32 K Mode VESA 1 280 x 800 x 16 K Mode [...]

3 Diagnostic Programs 3.5 System Test 3.5 System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU 1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, whi[...]

3.5 System Test 3 Diagnostic Programs CPU Speed Comparison --Whether you want to make a comparison of the CPU speed with the value set in ‘E xpected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Expected CPU Speed --Specify the expected CPU Speed value you want for further comparison. Allowable Error Rate -- Specify the Allowabl[...]

3 Diagnostic Programs 3.5 System Test 5. CPU Protected Mode Test This test item is to check whether CPU protected m ode instruction works normally. 6. MMX The test item is to confirm whether the CPU supports MMX instru ctions. Subtest 02 Boards 1. DMA Controller This test item is to check whethe r the DMA controller works norm ally. 2. Interval Tim[...]

3.5 System Test 3 Diagnostic Programs This test item is to check: 1. Whether the current system supports Plug-n-Play; 2. Whether there is an ESCD (Extended System Configuration D ata) in the BIOS; 3. Whether there is PCI-to-ISA bridge in the system; 4. Whether there is PCI bus in the sy stem. 6. ACPI Test ACPI test includes two sub-items as below: [...]

3 Diagnostic Programs 3.5 System Test 34 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual[...]

3.6 Memory Test 3 Diagnostic Programs 3.6 Memory Test This test module is to check whet her the mem o ry chip works norm ally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that in cludes two sub-items -- ROM Read and ROM Write Protection. RO M Read is to check whether BIOS ROM could be correctly read out, ROM Wr ite Prote[...]

3 Diagnostic Programs 3.6 Memory Test Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m emory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minut e) of the defin[...]

3.6 Memory Test 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 37 test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m[...]

3 Diagnostic Programs 3.6 Memory Test In addition to the above pattern test of th e memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test. Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole[...]

3.6 Memory Test 3 Diagnostic Programs The test item is to ensure that there is no short circuitry issue in mem ory chip. The parameter dialog window is the same as that in ‘Subtest 02 P attern’. Subtest 06 Walking 0’s Test The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same [...]

3 Diagnostic Programs 3.6 Memory Test 40 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual This test item is to check whether the data bus works normally. Subtest 12 Memory Speed Test This test item is to check the data -transferring rate for the ca che memory and the system memory.[...]

3.7 Storage 3 Diagnostic Programs 3.7 Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows: Password ： hard disk 1. Sequential/Random R/W This test item is to check t[...]

3 Diagnostic Programs 3.7 Storage LBA Start, LBA End --Specify the start and end byte in LBA (Large Block Address). Percent —Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined [...]

3.7 Storage 3 Diagnostic Programs Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking spee[...]

3 Diagnostic Programs 3.7 Storage 44 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual Subtest 02 ODD The ODD test runs on ID E CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and perf ormance. 1. Controller Test Check the CDROM controller’s status. 2. Data Transfer Rate Check the data trans[...]

3.10 Peripheral 3 Diagnostic Programs 3.8 Video This test item tests the video by: 1. displaying the figures in different graphic modes. 2. displaying the property and color of the characters in different text modes. User will confirm whether each video m ode works normally by judging whether the display is correct. It checks whether the video m em[...]

3 Diagnostic Programs 3.10 Peripheral It would display the below texts of th e different attributes in the screen: 1. Text in normal attribute; 2. Text in blinking normal attribute; 3. Text in inverse attribute; 4. Text in blinking inverse attribute; 5. Text in hi-intensity attribute; 6. Text in blinking hi-intensity attribute; Users need to check [...]

3.10 Peripheral 3 Diagnostic Programs 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a ch aracter defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foregroun[...]

3 Diagnostic Programs 3.10 Peripheral This test item is to check whether 80*25 Text Mode works normally. In the test, user is required to respond according to the instru ction in the screen. Subtest 02 640 * 480 VGA Mode This test item is to check whethe r 680*480 VGA Text mode works normally. In the test, user is required to respond according to t[...]

3.10 Peripheral 3 Diagnostic Programs Subtest 03 VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respon d following the instruction in the screen. 1. 640X480 Video Modes Test 2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 12 80 X 800 Vi[...]

3 Diagnostic Programs 3.10 Peripheral If press Ctrl+Break to force the test to term inate during execution of VESA Video Memory, the test program will not operate and display properly in f urther tests. Subtest 05 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Sub[...]

3.10 Peripheral 3 Diagnostic Programs Subtest 07 Register Test This test item is to check whether th e registers of the video adapter works normally. Subtest 08 Color Purity Test This test item is to check whether th e sy stem (the video adapter and the display) could display the purity color of re d, green, blue, black and white. In the test, user[...]

3 Diagnostic Programs 3.10 Peripheral Subtest 09 Direct Color Test This test item is to check the video adap ter ’s composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instru ction in the screen. Subtest 10 DAC/Palette Address This test item is to check the f unction of DAC regi[...]

3.10 Peripheral 3 Diagnostic Programs NOTE 1:AMD platform can’t support this item Subtest 11 BitBlt Engine Test This test item is to check whether th e BitBlt engine works norm ally. BitBlt is the abbreviation of ‘Bit Block Translate’, that means the copy of data block for 3 types, from video memory to video mem ory, from video memory to syst[...]

3 Diagnostic Programs 3.10 Peripheral NOTE 1:AMD platform can’t support this Test item 54 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual[...]

3.10 Peripheral 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 55 3.9 Communication (COMM) Subtest 01 LAN Card This test item is to check whether the m odule can detect the exis tence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the net[...]

3 Diagnostic Programs 3.10 Peripheral 3.10 Peripheral Subtest 01 Keyboard This test item is to check wh ether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point dev[...]

3.10 Peripheral 3 Diagnostic Programs Subtest 03 Led Test 1. Led Test Check whether the Device led works normally. NOTE 1:If The Machine is AMD Pl atform, The HDD LED is very Dim Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 57[...]

3 Diagnostic Programs 3.11Error Codes and Description 58 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee ’, and ‘dd’ is the device ID (1 ~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is th e error code of device[...]

3.11Error Codes and Description 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 59 04 (XMS)Mem ory Problem The test pattern read out from the extension memory is different from the one that has been written in this address. As above. 05 (XMS) Out Of Range Wrong parameters se tup. Check and reset[...]

3 Diagnostic Programs 3.11Error Codes and Description 60 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual configuration. 17 PCI to ISA Bridge Error PCI-ISA bridge errors. Repeat multiple times. If there is always the same error, replace the board. 18 ESCD Error ESCD errors. As above. 53 ACPI Table Test Error Errors wi[...]

3.11Error Codes and Description 3 Diagnostic Programs Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 61 15 VESA VRAM Test Error Physical problems with the video card or the monitor. Check whether there is any physical problem with the video card or the monitor. 16 AGP Test Error AGP configuration register errors. Ch[...]

3 Diagnostic Programs 3.11Error Codes and Description 62 Satellite L300D,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 01 Keyboard Map & Stroke Test Fail Keyboard Map & Stroke Test fails. Check the KBD connection and repeat the test. 03 Clock Line Test Fail Clock Line Test fails. As above. 04 Data Line Test Fail Data Line [...]

3.12 Quick Test Item List 3 Diagnostic Programs Satellite L300,Satellite Pro L300, EQUIUM L300,SATEGO L300 Mai ntenance Manual 63 3.12 Quick Test Item List Device Test Items Comment CPU Basic Functionality N PU Basic Functions CPU Information Memory BIOS ROM Cache Me mory Bit Stuck High Test 10% or 3 minutes Bit Stuck Low Test 10% or 3 minutes Addr[...]

Chapter 4 Replacement Procedures 4 1[...]

4 Replacement Procedures 4-ii Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual[...]

4 Replacement Procedures Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-iii Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 Safety Precautions ..........................................................[...]

4 Replacement Procedures 4-iv Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the Keyboard ...................................................................................... 4-23 4.5 MDC Module .......................................................................................................[...]

4 Replacement Procedures Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-v Removing the FL Inverter Board ....................................................................... 4-47 Installing the FL I nverter Board ........................................................................ 4-48 4.15 LCD Module[...]

4 Replacement Procedures 4-vi Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Figures Figure 4-1 Removing the battery pack ................................................................................. 4-8 Figure 4-2 Removing the PC card .......................................................................[...]

4 Replacement Procedures Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-vii Figure 4-31 Removing CCD board and MIC ...................................................................... 4-52 Figure 4-32 Removing the speakers ....................................................................................[...]

4.1 General 4 Replacement Procedures 4 1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures m ay not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down [...]

4 Replacement Procedures 4.1 General 4-2 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorize[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-3 CAUTION: 1. Before replacing a component, make su re that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. 2. To avoid interna[...]

4 Replacement Procedures 4.1 General 4-4 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Before You Begin Before you begin to disassembly the computer, keep in m ind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and acc[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-5 Disassembly Procedures The cable connectors come in these two basic types:  Pressure plate connectors  Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's[...]

4 Replacement Procedures 4.1 General 4-6 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipm ent. The proper use of this equipment will ensure successf[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-7 Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:  Screws of an even-numbered length Brown  Screws of an odd-numbered length Whit[...]

4 Replacement Procedures 4.1 General Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer upside d[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-9 Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handlin[...]

4 Replacement Procedures 4.1 General Removing the Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using. 1. Push the [...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-11 Installing the Optional PC Card Install the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and[...]

4 Replacement Procedures 4.1 General Removing the Memory Card Remove the mem ory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Push the memory card to be rem oved until it stops then release the mem ory card. 3. When the mem ory card pops out, grasp[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-13 Installing the Memory Card Install the memory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the memory card gently until it stops and is se[...]

4 Replacement Procedures 4.1 General Removing the Optional Memory Remove the optional mem ory (module) according to the following procedures and Figures 4- 4, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1.[...]

4.1 General 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-15 Installing the Optional Memory Install the optional memory (m odule) according to the following procedures and Figures 4-4, after checking that the computer is turned off in boot mode. Note: The slot A is reserved for main [...]

4 Replacement Procedures 4.2 HDD 4.2 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4-5, 4- 6. 1. Release the two HDD cover screws securing the HDD cov[...]

4.2 HDD 4 Replacement Procedures 3. Remove the HDD pack by pulling on the tab attached to the pack, following the direction of the arrows. NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 4. Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black fl[...]

4 Replacement Procedures 4.2 HDD 4-18 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the HDD Install the HDD according to the following procedures and Figures 4-5, 4-6. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD chassis. 2. Secure the HDD and its chassis with t[...]

4.3 ODD Bay Module 4 Replacement Procedures 4.3 ODD Bay Module Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedur[...]

4 Replacement Procedures 4.3 ODD Bay Module 4-20 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the ODD Bay Module Install the ODD bay module according to the following procedures and Figures 4-7. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into [...]

4.3 ODD Bay Module 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-8. 1. Remove two M2x3 black flat head screws. 2. Remove the bracket. Bracket M[...]

4 Replacement Procedures 4.4 Keyboard 4.4 Keyboard Removing Keyboard Remove the Keyboard according to the following procedures and Figure 4-9. 1. Release the following 12 latches on the keyboard cover, in that order: - One latch on each of the left and right sides - Five bottom latches - Five front latches 2. Remove the keyboard cover. 3. Remove tw[...]

4.4 Keyboard 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-23 Installing the Keyboard Install the keyboard according to the following procedures and Figure 4-9. 1. Connect the keyboard cable to CN11 on the system board. 2. Secure the keyboard with two M2x3 black bind screws. 3. Place[...]

4 Replacement Procedures 4.5 MDC Module 4.5 MDC Module Removing the MDC Module Remove the MDC Module (Modem Daughter Card) according to the following procedures and Figures 4-10, after checking that the computer is turned off in boot mode. CAUTION : Remove the MDC module after turning off the computer. If this is violated, the computer or MDC modul[...]

4.5 MDC Module 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-25 Installing the MDC Module Install the MDC module according to the following procedures and Figures 4-10, after checking that the computer is turned off in boot mode. CAUTION : Install the MDC module after turning off the[...]

4 Replacement Procedures 4.6 Wireless LAN card 4.6 Wireless LAN Card Removing the Wireless LAN Card Remove the wireless LAN card according to the following procedures and Figure 4-11. CAUTION : Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with swe[...]

4.6 Wireless LAN Card 4 Replacement Procedures Satellite L300/ 305D/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-27 Installing the Wireless LAN Card Install the wireless LAN card according to the following procedures and Figure 4-11. 1. Insert the wireless LAN card into the CN10 an angle of 45 degrees. 2. Press down on the wir[...]

4 Replacement Procedures 4.7 Top Cover 4 1 4.7 Top Cover Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-12 and 4-13. 1. Turn the computer upside down and remove the following 14 screws: - Eleven M2.5x7 black flat head screws and three M2x4 black flat head screws. M2x3 black flat head screw M2 5x6 bla[...]

4.7 Top Cover 4 Replacement Procedures M2 5x6 black flat head screw . Latch Touch pad board flat cable Speakers cable Top cover CN8 CN9 Figure 4-13 Removing the top cover Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-12, 4-13. 1. Seat the top cover, adjusting its positio[...]

4 Replacement Procedures 4.7 Display Assembly 4.8 Display Assembly Removing the Display Assembly CAUTION : Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-14, 4-15. 1. Turn the computer upside down and remove two M2.5x6 [...]

4.7 Display Assembly 4 Replacement Procedures M2 5x6 black flat head screw . LCD FL cable CCD cable MIC cable Wireless LAN antenna CN5 CN7 CN13 Figure 4-15 Removing the display assembly Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-14, 4-15. 1. Place the display panel in the correct[...]

4 Replacement Procedures 4.9 System Board 4.9 System Board Removing the System Board NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board and Figure 4-16. 1. Remove the CRT cable from CN4 on the system board. 2. Remove the power button board cabl[...]

4.9 System Board 4 Replacement Procedures Satellite L300 / L305/Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-33 Installing the System Board Install the System Board, AC-IN Cable and ODD Extended Board according to the following procedures and figure 4-16. NOTE: Be careful of the eject button for the PC card. It can be damaged w[...]

4 Replacement Procedures 4.10 CPU Cooling Module and Fan 4-34 Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4.10 CPU Cooling Module and Fan CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before startin[...]

4.10 CPU Cooling Module and Fan 4 Replacement Procedures M2 5x5 white flat head screw . Fan Tape CN501 Figure 4-17 Removing the fan M2x3 white flat head screw CPU cooling module bracket CPU cooling module Figure 4-18 Removing the CPU cooling module Satellite L300 / L305/Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-35[...]

4 Replacement Procedures 4.10 CPU Cooling Module and Fan Figure 4-19 Applying silicon grease Installing the CPU Cooling Module and Fan(For Intel CPU) Install the cooling Module according to the following procedures and Figures 4-17, 4-18 and 4-19. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the cor[...]

4.10 CPU Cooling Module and Fan 4 Replacement Procedures Satellite L300 / L305/Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-37 CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch [...]

4 Replacement Procedures 4.10 CPU Cooling Module and Fan M2 5x5 white flat head screw . Fan Tape CN501 Figure 4-20 Removing the fan M2x3 white flat head screw CPU cooling module bracket CPU cooling module CPU cooling module secure screw Figure 4-21 Removing the CPU cooling module 4-38 Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L3[...]

4.10 CPU Cooling Module and Fan 4 Replacement Procedures Figure 4-22 Applying silicon grease Installing the CPU Cooling Module and Fan(For AMD CPU) Install the cooling Module according to the following procedures and Figures 4-20, 4-21 and 4-22. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the corre[...]

4 Replacement Procedures 4.11 CPU 4.11 CPU Removing the CPU Remove the CPU according to the following procedures and Figures 4-23, 4-24 and 4-25. CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. NOTE: FOXCONN CPU socket will be 180 degr[...]

4.11 CPU 4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures and Figures 4-24, 4-25. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. Figure 4-24 Installing th[...]

4 Replacement Procedures 4.11 CPU 3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left. Figure 4-25 Securing the CPU 4-42 Satellite L300/L305 / Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual[...]

4.12 Broadcom Card 4 Replacement Procedures 4.12 Broadcom Card Removing the Broadcom Card Remove the Broadcom card according to the following procedures and Figure 4-26. CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands. Broadcom card can fail if they are contaminated with sweat, natural oils, etc. f[...]

4 Replacement Procedures 4.12 Broadcom Card 4-44 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the Broadcom Card Install the Broadcom card according to the following procedures and Figure 4-26. 1. Insert the Broadcom card into the connector an angle of 45 degrees. 2. Press down on the Broadcom card [...]

4.13 Display Mask 4 Replacement Procedures 4.13 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-27. 1. Remove the following 4 seals on the display module in that order: - Two black seals on the bottom - Two black seals on the top 2. Remove the following 4 screws on the display module[...]

4 Replacement Procedures 4.13 Display Mask 4-46 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the Display Mask Install the display mask according to the following procedures and Figure 4-27. 1. Seat the display mask in the correct position and secure the following 24 latches, in that order: - Ten to[...]

4.14 FL Inverter Board 4 Replacement Procedures 4.14 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-28. 1. Remove one M2.5x5 black flat head screw. M2 5x5 black flat head screw . FL inverter board HV cable LCD FL cable Figure 4-28 Removing the FL inverter board 2. Li[...]

4 Replacement Procedures 4.14 FL Inverter Board 4-48 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-28. 1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector[...]

4.15 LCD Module 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4 - 49 4.15 LCD Module NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or [...]

4 Replacement Procedures 4.15 LCD Module Left LCD bracket LCD module M2x3 black flat head screw M2x3 black flat head screw Right LCD bracket M2 5x5 black flat head screw . Figure 4-29 Removing the LCD module and screws 6. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable. LCD module LCD LF cable / Figure 4-30 Removing the[...]

4.15 LCD Module 4 Replacement Procedures Installing the LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the LCD module according to the following procedures and Figures 4-29, 4-30. 1. Turn the LCD upside down. 2. Connect the LCD/FL cable to the LCD module connector. 3. Turn the LCD right [...]

4 Replacement Procedures 4.16 CCD Board and MIC 4.16 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-31. 1. Remove the CCD module with CCD cable from display rear cover. 2. Disconnect the CCD cable from the CCD module connector. CCD module CCD cable MIC cable Display r[...]

4.16 CCD Board and MIC 4 Replacement Procedures Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4 - 53 Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-31. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the [...]

4 Replacement Procedures 4.17 Speaker 4.17 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4-32. 1. Remove two M2x3 black flat head screw securing the left speaker. 2. Remove two M2x3 black flat head screws securing the right speaker. 3. Remove the left and right speakers. M2x3 black flat head scr[...]

4.18 Touch Pad and Button Board 4 Replacement Procedure s 4.18 Touch Pad and Button Board Removing the Touch Pad and Button Board Remove the touch pad and button board according to the following procedures and Figure 4- 33. 1. Disconnect the touch pad flat cables from CN5000 on the button board and touch pad. 2. Remove two M2x3 black flat head scre[...]

4 Replacement Procedures 4.18 Touch Pad and Button Board 4-56 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the Touch Pad and Button Board Install the touch pad and button board accordi ng to the following procedures and Figure 4-33. 1. Seat the touch pad, touch pad bracket in the correct position a[...]

4.20 USB Cable, CRT Cable, Power Button Board , 4 Replacement Procedure s AC-IN cable and RJ11 Cable 4.19 USB cable, CRT cable, Power Button Board, AC-IN cable and RJ11 cable Removing USB cable, CRT cable, Power Button Board, AC-IN cable and RJ11 cable Remove the USB cable, CRT cable, Power Button board, AC-IN cable and RJ11 cable according to the [...]

4 Replacement Procedures 4.20 USB Cable, CRT Cable, Power Button Board, AC- IN cable and RJ11 cable 4-58 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual Installing the USB cable, CRT cable, Power Button Board, AC-IN cable and RJ11 cable Install the USB cable, CRT cable, Power Button Board, AC-IN cable and RJ11 c[...]

6000 1 次 Appendices[...]

Appendices App-ii Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout ..............................................................................................[...]

Appendices Satellite L300/L305/Satellite Pro L300/E QUIUM L300/SATEGO L300 Maintenance Manual App-iii C.24 CN508 Bri dge Media Slot Connector (21-Pin) ............................................ C-17 C.25 CN510 Broadcom Decoder Connector (52-Pin) .......................................... C-17 C.26 JACK500 RJ45 LAN Connector (12-Pin) .............[...]

Apx. A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD c over, be sure to seat it so that it is pr[...]

Appendices Apx. A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do [...]

Apx. A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite L30[...]

Appendices Apx. A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. A-4 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/[...]

Apx. A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use pack ing m aterial that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite L300/L305/Sate[...]

Apx. B Board Layout Appendices Appendix B Appendix B Board Layout B.1 System Board Front View Figure B-1 Board Layout (Front) Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual B-1[...]

Appendices Apx. B Board Layout Figure B-2 Board Layout (Back) B-2 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-1 Appendix C C.1 CN1 Power Board Connector (4-Pin) ........................................................ C-2 C.2 CN2 Switch Board Connector (12-Pin) ..................................................... C-2 C.3 CN3 AC-In Cable Co[...]

Appendices Apx. C Pin Assignments C-2 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Appendix C Appendix C Pin Assignments System Board C.1 CN1 Power Board Connector (4-Pin) Table C-1 Power Board Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PWR_SWIN#_3 I 2 DGND - 3 DGND - 4 D[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-3 3 DGND - 4 N$1054331 - 5 DGND - 6 N$1217468 - 7 DGND - 8 VSYNC O 9 DGND - 10 HSYNC O 11 - - 12 N$1158229 - 13 N$1158230 - 14 - - C.5 CN5 LCD/FL Inverter Cable Connector (40-Pin) Table C-5 LCD/FL Inverter Cable Connector Pin Assign[...]

Appendices Apx. C Pin Assignments C-4 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 MDC I/O 3 MC97_3S_SDOUT I/O 4 - - 5 DGND - 6 MDC I/O 7 MC97_3S_SYNC I/O 8 DGND - 9 N$737061 - 10 DGND - 11 MC97_3S_RST# I/O 12 MC97_3S_BITCLK I/O C.7 CN7 CCD Camera Cable [...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-5 C.10 CN10 Wireless LAN Module Connector (52-Pin) Table C-10 Wireless LAN Module Connector Pin Assignments (52-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PCIE_WAKE# I/O 2 +V3S O 3 - - 4 DGND - 5 - - 6 +V1.5S O 7 CLKREQ_[...]

Appendices Apx. C Pin Assignments C-6 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$850859 I 2 N$850860 I 3 N$850855 I 4 +V3S O 5 SCAN_IN(1) O 6 SCAN_IN(6) O 7 SCAN_IN(5) O 8 SCAN_IN(0) O 9 SCAN_IN(4) O 10 SCAN_IN(3) O 11 SCAN_IN(2) O 12 SCAN_IN(7) O 13 SCAN_OUT[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-7 25 PCIE_C_TXP5 I/O 26 DGND - C.13 CN13 Internal MIC Phone Cable Connector (2-Pin) Table C-13 Internal MIC Phone Ca ble Connector Pin Assignments (2-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 ANAGND - 2 MIC_IN I C.14 CN[...]

Appendices Apx. C Pin Assignments C-8 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 29 ACARD_3S_AD26 I/O 30 ACARD_3S_AD27 I/O 31 ACARD_3S_AD29 I/O 32 ACARD_3S_D(2)_RFU I/O 33 ACARD_3S_CLKRUN# I/O 34 DGND - 35 DGND - 36 ACARD_3S_CD1# I/O 37 ACARD_3S_AD2 I/O 38 ACARD_3S_AD4 I/O 39 ACARD_3S_AD6 I/O 40 ACARD_3S_D(14)[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-9 21 - - 22 - - C.17 CN500 Battery Pack Connector (9-Pin) Table C-17 Battery Pack Connector Pin Assignments (9-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$1089074 O 2 N$1089074 O 3 N$1089075 - 4 DGND - 5 N$1089067 - 6 N[...]

Appendices Apx. C Pin Assignments C-10 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 23 MB_DATA(8) I/O 24 DGND - 25 MB_DATA(9) I/O 26 MB_DM(1) O 27 DGND - 28 DGND - 29 MB_DQS#(1) I/O 30 MB_CLK_DDR4 I/O 31 MB_DQS(1) I/O 32 MB_CLK_DDR4# I/O 33 DGND - 34 DGND - 35 MB_DATA(10) I/O 36 MB_DATA(14) I/O 37 MB_DATA(11) I/[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-11 93 MB_A(8) O 94 MB_A(6) O 95 +V1.8 O 96 +V1.8 O 97 MB_A(5) O 98 MB_A(4) O 99 MB_A(3) O 100 MB_A(2) O 101 MB_A(1) O 102 MB_A(0) O 103 +V1.8 O 104 +V1.8 O 105 MB_A(10) O 106 MB_A(16) O 107 MB_A(15) O 108 MB_RAS# I/O 109 MB_WE# I/O [...]

Appendices Apx. C Pin Assignments C-12 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 163 - - 164 MB_CLK_DDR2 I/O 165 DGND - 166 MB_CLK_DDR2# I/O 167 MB_DQS#(6) I/O 168 DGND - 169 MB_DQS(6) I/O 170 MB_DM(6) I/O 171 DGND - 172 DGND - 173 MB_DATA(50) I/O 174 MB_DATA(54) I/O 175 MB_DATA(51) I/O 176 MB_DATA(55) I/O 17[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-13 23 MA_DATA(8) I/O 24 DGND - 25 MA_DATA(9) I/O 26 MA_DM(1) O 27 DGND - 28 DGND - 29 MA_DQS#(1) I/O 30 MA_CLK_DDR4 I/O 31 MA_DQS(1) I/O 32 MA_CLK_DDR4# I/O 33 DGND - 34 DGND - 35 MA_DATA(10) I/O 36 MA_DATA(14) I/O 37 MA_DATA(11) I/[...]

Appendices Apx. C Pin Assignments C-14 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 93 MA_A(8) O 94 MA_A(6) O 95 +V1.8 O 96 +V1.8 O 97 MA_A(5) O 98 MA_A(4) O 99 MA_A(3) O 100 MA_A(2) O 101 MA_A(1) O 102 MA_A(0) O 103 +V1.8 O 104 +V1.8 O 105 MA_A(10) O 106 MA_A(16) O 107 MA_A(15) O 108 MA_RAS# I/O 109 MA_WE# I/O [...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-15 163 - - 164 MA_CLK_DDR2 I/O 165 DGND - 166 MA_CLK_DDR2# I/O 167 MA_DQS#(6) I/O 168 DGND - 169 MA_DQS(6) I/O 170 MA_DM(6) I/O 171 DGND - 172 DGND - 173 MA_DATA(50) I/O 174 MA_DATA(54) I/O 175 MA_DATA(51) I/O 176 MA_DATA(55) I/O 17[...]

Appendices Apx. C Pin Assignments C-16 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 23 DGND - 24 PIDE_3S_IOR# I/O 25 PIDE_3S_IOW# I/O 26 DGND - 27 PIDE_3S_IORDY I/O 28 PIDE_3S_DACK# I/O 29 PIDE_3S_IRQ I/O 30 N$777529 - 31 PIDE_3S_A(1) I/O 32 - - 33 PIDE_3S_A(0) I/O 34 PIDE_3S_A(2) I/O 35 PIDE_3S_CS#(0) I/O 36 PI[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-17 13 HDMI_CEC I/O 14 - - 15 HDMI_SCLDDC O 16 HDMI_SDADDC O 17 DGND - 18 N$1138481 - 19 N$987340 - - - - C.24 CN508 Bridge Media Slot Connector (21-Pin) Table C-24 Bridge Media Slot Connector Pin Assignments (21-Pin) Pin No. Signal [...]

Appendices Apx. C Pin Assignments C-18 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual 19 - - 20 - - 21 DGND - 22 BUF_PLT_RST# O 23 PCIE_C_RXN3 I 24 +V3S O 25 PCIE_C_RXP3 I 26 DGND - 27 DGND - 28 +V1.5S O 29 DGND - 30 - - 31 PCIE_C_TXN3 O 32 - - 33 PCIE_C_TXP3 O 34 DGND - 35 DGND - 36 - - 37 - - 38 - - 39 - - 40 DG[...]

Appendices Apx. C Pin Assignments Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C-19 3 N$844264 - 4 HPS O 5 ANAGND - 6 - - C.28 JACK502 External MIC Connector (6-Pin) Table C-28 External MIC Connector Pin Assignments (6-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$987986 - 2 N$981141 - 3 N$981142 - 4 [...]

Appendices Apx. C Pin Assignments C-20 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual C.31 CN5001 Touch Pad Board Cable Connector (12-Pin) Table C-31 Touch Pad Board Cable Connector Pin Assignments (12-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND_TP - 2 DB_TP_LED_ON I/O 3 TP_IM_CLK_5 I/O 4 TP_IM_DAT_[...]

Keyboard Scan/Character Codes Appendices Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual D-1 Apx. D Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan Codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 [...]

Appendices Keyboard Scan/Character Codes D-2 Satellite L300/L305/Satellite Pr o L300 /EQUIUM L3 00/SATEGO L300 Maintenance Manual Table D-1 Scan Codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 2[...]

Keyboard Scan/Character Codes Appendices Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual D-3 Table D-1 Scan Codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F[...]

Appendices Keyboard Scan/Character Codes D-4 Satellite L300/L305/Satellite Pr o L300 /EQUIUM L3 00/SATEGO L300 Maintenance Manual Table D-1 Scan Codes (set 1 and set 2) (4/4) Cap Code set 1 Code set 2 No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 7 F0 7 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn ?[...]

Keyboard Scan/Character Codes Appendices Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual D-5 Table D-2 Scan Codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 5 5 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 7 5 I N S E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0[...]

Appendices Keyboard Scan/Character Codes D-6 Satellite L300/L305/Satellite Pr o L300 /EQUIUM L3 00/SATEGO L300 Maintenance Manual Table D-3 Scan Codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 7 5 I N S E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 7 6 D E L E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F[...]

Keyboard Scan/Character Codes Appendices Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual D-7 Table D-5 Scan Codes in overlay mode Code set 1 Code set 2 Cap No. Ke ytop Make Break Make Break 08 7 (7) 47 C7 6C F0 6C 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I[...]

Appendices Keyboard Scan/Character Codes D-8 Satellite L300/L305/Satellite Pr o L300 /EQUIUM L3 00/SATEGO L300 Maintenance Manual Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co m m on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Apx. E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 US keyboard E.2 Japan (JP) Keyboard Figure E-2 JP keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual E-1[...]

Appendices Apx. E Key Layout E.3 Spanish (SP) Keyboard Figure E-3 SP keyboard E.4 Korean (KR) Keyboard Figure E-4 KR keyboard E-2 Satellite L300/L305/Satellite Pro L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.5 Canadian Bilingual (QB) Ke yboar d Figure E-5 QB keyboard E.6 French (FR) Keyboard Figure E-6 FR keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual E-3[...]

Appendices Apx. E Key Layout E.7 German (GR) Keyboard Figure E-7 GR keyboard E.8 Italian (IT) Keyboard Figure E-8 IT keyboard E-4 Satellite L300/L305/Satellite Pr o L300/EQUIUM L300 /SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.9 Taiwan (TC) Keyboard Figure E-9 TC keyboard E.10 Portuguese (PT) Keyboard Figure E-10 PT keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual E-5[...]

Appendices Apx. E Key Layout E.11 DU, UE, US International (USE) Keyboard Figure E-11 USE keyboard E.12 Arabic (AR) Keyboard Figure E-12 AR keyboard E-6 Satellite L300/L305/Satellite Pr o L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.13 Belgian (BE) Keyboard Figure E-13 BE keyboard E.14 Russian (RU) Keyboard Figure E-14 RU keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual E-7[...]

Appendices Apx. E Key Layout E.15 Swiss/Switzerland (SL) Keyboard Figure E-15 SL keyboard E.16 Swedish (SW) Keyboard Figure E-16 SW keyboard E-8 Satellite L300/L305/Satellite Pr o L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.17 Norwegian (NO) Keyboard Figure E-17 NO keyboard E.18 Danish (DK) Keyboard Figure E-18 DK keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300 /SATEGO L300 Maintenance Manual E-9[...]

Appendices Apx. E Key Layout E.19 Turkey (TR) Keyboard Figure E-19 TR keyboard E.20 Greek (GK) Keyboard Figure E-20 GK keyboard E-10 Satellite L300/L305/Satellite Pr o L300/EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.21 Canadian Multinational (CM) Keyboard Figure E-21 CM keyboard E.22 Herbrew (HE) Keyboard Figure E-22 HE keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300/S ATEGO L300 Maintenance Manual E-11[...]

Appendices Apx. E Key Layout E.23 Czech (CZ) Keyboard Figure E-23 CZ keyboard E.24 Scandinavian (N5) Keyboard Figure E-24 N5 keyboard E-12 Satellite L300/L305/Satellite Pro L300 /EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.25 Hungary (HU) Keyboard Figure E-25 HU keyboard E.26 Slovakian (SK) Keyboard Figure E-26 SK keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300/S ATEGO L300 Maintenance Manual E-13[...]

Appendices Apx. E Key Layout E.27 Yugoslavia (YU) Keyboard Figure E-27 YU keyboard E.28 Thai (TH) Keyboard Figure E-28 TH keyboard E-14 Satellite L300/L305/Satellite Pro L300 /EQUIUM L300/SATEGO L300 Maintenance Manual[...]

Apx. E Key Layout Appendices E.29 United Kingdom (EN) Keyboard Figure E-29 EN keyboard E.30 Turkish F (TF) Keyboard Figure E-30 TF keyboard Satellite L300/L305/Sa tellite Pro L300/EQUIUM L300/S ATEGO L300 Maintenance Manual E-15[...]

Apx. F BIOS Rewrite Procedures Appendices Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual F-1 Appendix G Appendix F BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewritin[...]

Apx. G EC/KBC Rewrite Procedures Appendices Satellite L300/L305/Satellite Pro L300/EQUIUM L 300/SATEGO L300 Maintenance Manual G-1 Appendix H Appendix G EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  BIOS/EC/KB[...]