Toshiba M700/M710 manual

User ’ s Manual PORTÉGÉ M700/M710[...]

User ’s Manual ii T able of Content s Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi T rademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

User ’s Manual iii PORTÉGÉ M700/M710 Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

User ’s Manual iv PORTÉGÉ M700/M710 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 TOSHIBA Passw ord Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 T ablet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

User ’s Manual v PORTÉGÉ M700/M710 Appendix I AC Power Cord and Connectors Certification agen cies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1 Appendix J TOSHIBA Anti-t hef t Protection Timer Appendix K Legal Footnotes Non-applicable Icons *1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

User ’s Manual vi PORTÉGÉ M700/M710 Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be repro duced in any form without the prior written permission of TOSHIBA. No p at ent liability is assumed, with respect to the use of the information contained herein. TOSHIBA POR T ÉGÉ M700/M710 P[...]

User ’s Manual vii PORTÉGÉ M700/M710 FCC information FCC notice "Declaration of Conform ity Information" This equipment has been tested and fo und to comply with th e limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide rea sonable prot ection again st harmful interference in [...]

User ’s Manual viii PORTÉGÉ M700/M710 EU Conformity S t atement This product and - if applicable - t he supplied accessories too are marke d with "CE" and comply therefore wit h th e appl icable harmonized Europe an standards listed under the Low V oltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TT E Di rective[...]

User ’s Manual ix PORTÉGÉ M700/M710 In the event of problems, you should contact your equipment supp lier in the first instance. Network Com p atibility S tatemen t This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the add iti onal requirements conditional in EG[...]

User ’s Manual x PORTÉGÉ M700/M710 This label is located on the module. Pursuant to FC C CFR 47 , P art 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the mode m ■ The registration number t hat is loca[...]

User ’s Manual xi PORTÉGÉ M700/M710 T elephone comp any p roced ures The goal of the telephone co mpany is to provide you with the best service it can. In order to do this, it may occasionally be ne cessary for them to make changes in their equipment, opera ti ons, or procedures. If these changes might affect your service or the operation of yo[...]

User ’s Manual xii PORTÉGÉ M700/M710 Instructions for IC CS -03 certified equipment 1. The Industry Canada label identi fies certified e quipment. This certification means that the equipment meets certain telecommunications network prot ective, operational and safety requirements as prescribed in the appropriate T erminal Equipment T echnical R[...]

User ’s Manual xiii PORTÉGÉ M700/M710 Notes for Users in Australia and New Zealand Modem w a rning notice for Australia Modems connected to the Australian te lecoms network must have a valid Austel permit. This modem has been desi gned to specifica lly configu re to ensure compliance with Austel stan dards when the country/region selection is s[...]

User ’s Manual xiv PORTÉGÉ M700/M710 ■ Some parameters required fo r compliance with T elecom’s P TC S pecifications are dependent on th e equipment (PC) associ ate d with this modem. The associated equipm en t shall be set to operate within the following limits for complianc e with T elecom S pecifications: a/ There shall be no more than 1[...]

User ’s Manual xv PORTÉGÉ M700/M710 ■ The transmit level from this device is set at a fixe d level and because o f this there may be circumstances where the performance is less than optimal. Before rep orting such occurrences a s faults, please check the line with a standard T elepermitted telephone, and only report a fault if the phone perfo[...]

User ’s Manual xvi PORTÉGÉ M700/M710 Following information is only for EU-memb er st ates: Description on Laser specification The optical disc dri ve such as DVD Super Mu lti drive th at is used in thi s computer is equipped with laser . The classification label with the following sentence is affixed to the surface of the dri ve. CLASS 1 LASER [...]

User ’s Manual xvii Preface Congratulations on your purchase of the PORTÉGÉ M700/M710 series computer . This powerfu l notebo ok computer provides excellent expansion capability , includes multimedia functionality , and is designed to provide years of reliable, high -performance computing. This manual tel ls how to set up and begin using your P[...]

User ’s Manual xviii PORTÉGÉ M700/M710 Icons Icons identify ports, dials, and other parts of your computer . The indicator pane l al so us es icons to iden ti fy th e co mponent s it is providi n g in formation on. Keys The keyboard keys are used in th e te xt to describe many computer operations. A distincti ve typeface ident ifies the key top[...]

User ’s Manual xix PORTÉGÉ M700/M710 T erminology This term is defined in this document as follows: Star t The word " Sta rt " refers to the " " button in Micros oft ® Windows Vista ® .[...]

User ’s Manual xx General Precautions TOSHIBA computers are designed to optimize safety , minimize strain and withstand the rigors of portability . Ho wever , certain precautions should be observed to further reduce the risk of personal injury or damag e to the computer . Be certain to read the general precau tions below and to note the cautions [...]

User ’s Manual xxi PORTÉGÉ M700/M710 Heat injury ■ Avoid prolonged physical contact with the computer . If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to th e touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on y[...]

User ’s Manual 1-1 Chapter 1 Getting S t arted This chapter provides an equipment checklist, and basic info rmation to start using your computer . Equipment checklist Carefully unpack your comp uter , taking care to save the box and packaging materials for future use. Hardware Check to make sure you have al l the following items: ■ PORTÉGÉ M7[...]

User ’s Manual 1-2 Getting S tarted Documentation ■ PORTÉGÉ M700/M710 Series User Information Guide ■ Instruction Manual for Safety and Comfort ■ End User License Agreement If any of the items are missing or damaged, contact your dealer immediately . Sof tware The following Wi ndo ws ® operating system and uti lity sof tware are pre- ins[...]

User ’s Manual 1-3 Getting S tarted Getting St arted This section provides basic information to start using your computer . It covers the following topics: ■ About the T ablet mode ■ Connecting the AC adaptor ■ Opening the display ■ T urning on the power ■ S tarting up for the first time ■ T urning off the power ■ Resta r ti n g th [...]

User ’s Manual 1-4 Getting S tarted Connecting the A C ada ptor Attach the AC adaptor when you need to cha rge the battery or you want to operate from AC power . It is also th e fastest way to get started, because the battery pack will need to be charged before you can operate from battery power . The AC adaptor can be connected to any po wer sou[...]

User ’s Manual 1-5 Getting S tarted 1. Connect the power cord to the AC adaptor . Figure 1-1 Connecting the power cord to the AC adap tor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adap tor (3-pin plug) 2. Connect the AC adaptor ’s DC output plug to the DC IN 15V jack on the back of the computer . Figure 1-3 Connecting the DC o[...]

User ’s Manual 1-6 Getting S tarted Opening the disp lay The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main b ody of the computer is not raised, slowly lift the display panel - this will allow the angle of the d isplay panel to be adjusted to provide opti [...]

User ’s Manual 1-7 Getting S tarted T urning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Powe r-Up Modes fo r more information. 1. Open the display panel. 2. Slide the Power Button Lock Switch to [...]

User ’s Manual 1-8 Getting S tarted 3. Click Star t . 4. Click the arrow button ( ) located in the p ower management buttons ( ) and select Shut Down from the menu. 5. T urn off any peripheral devices connected to your computer . Sleep Mode If you have to interrupt your work, you are a ble to turn off the power without exiting from your software [...]

User ’s Manual 1-9 Getting S tarted Benefits of Sleep Mode The Sleep Mode feature provide s the following benefits: ■ Restores the previous workin g environment more ra pidly than does the Hibernation Mode feature. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the S[...]

User ’s Manual 1-10 Getting S tarted When you turn the power back on, you can continue where you left when you shut down the computer . Sleep Mode limitations Sleep Mode will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to st atic electricity or electrica[...]

User ’s Manual 1-1 1 Getting S tarted S tarting Hibernation Mode T o enter Hibernation Mode, follow the steps below . 1. Click Start . 2. Click the arrow button ( ) in the power management buttons ( ) and select Hibernate from the menu. Automatic Hibernation Mode The computer can be configured to ent er Hibernation Mode auto matically when you pr[...]

User ’s Manual 1-12 Getting S tarted ■ Press the power button and hold it do wn fo r five seconds. Once the computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button. System Recovery Opti ons About 1.5GB hidden partition is alloca ted on the hard disk drive for the System[...]

User ’s Manual 1-13 Getting S tarted System Recovery This section describes the creation of Recovery Discs and their use. Creating Optical Reco very Discs This section describes how to create Recovery Discs. A recovery image of the software on your computer i s stored on the hard disk drive, and can be copied to ei ther CD or DVD media by using t[...]

User ’s Manual 1-14 Getting S tarted Restoring the pre-in st alled sof tw are from the Reco very hard disk drive A portion of the total hard disk dr ive space is configured as a hidden recovery partition. This p artition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your har[...]

User ’s Manual 1-15 Getting S tarted Restoring the pre-inst alled sof tw are from your crea ted Re covery Discs If the pre-installed files are damaged , you are able to either use the Recovery Discs you have created or the hard disk drive recovery proce ss to restore the computer to the state it was in when you originally received it. T o perform[...]

User ’s Manual 2-1 Chapter 2 The Grand T our This chapter identifies the various co mponen ts of the computer - it is recommended that you beco me famili ar with each before you opera te the computer . Front with the display closed The following fig ure shows the computer ’ s front with its display panel in the closed position. Figure 2-1 Front[...]

User ’s Manual 2-2 The Grand T our ■ Tu r n W i - F i ® , Bluetooth and Wireless WAN functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury . Follow the in struction of your medical devic[...]

User ’s Manual 2-3 The Grand T our Lef t side The following figure shows the comp uter ’s left side. Figure 2-2 The left side of the computer Cooling vents Universal Serial Bus (USB 2.0) ports PC Card slot (or Smart Card slot) PC Card eject button Security lock slot The computer is equipped with eithe r a PC Card slot or a Smar t Card slo t. Co[...]

User ’s Manual 2-4 The Grand T our Right side The following figure shows the computer ’ s right side. Figure 2-3 The right side of the computer Keep foreign metal objects, such as screws, staples and paper clips, out of the PC Card slot. Foreign metal objects can create a short circuit, which can cause damage a nd fire, possibl y resulting in s[...]

User ’s Manual 2-5 The Grand T our Back The following figure shows the comp uter ’s back. Figure 2-4 The back of the computer Ultra Slim Bay A DVD Super Multi drive or Ultra Slim Bay HDD Adaptor can be installed in the Ultra Slim Bay . Some models are equipped with a DVD Super Multi drive or U ltra Slim Bay HDD Ada ptor . Modem jack The modem j[...]

User ’s Manual 2-6 The Grand T our Keep foreign metal objects, such as scr ews, staples and paper clips, out of the USB connectors. Foreign metal ob jects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury . Please note that it is not possible to confir m the operation of all functi ons of all USB de[...]

User ’s Manual 2-7 The Grand T our Underside The following figure shows the undersi de of the computer . Y ou should ensure that the disp lay is closed befo re the computer is turned over to avoid causing any damage. Figure 2-5 The underside of the computer Memory module slot Battery release latch Bat tery lock Notch Docking port Battery pack HDD[...]

User ’s Manual 2-8 The Grand T our Memory module slot The slot B m emory module is located here. The memory module slot allows for the installation, replacement and removal of additiona l me mory module. Refer to the Additional memory module section in Chapter 3, Hardware, Utilities and Op tions. HDD p ack cover screws The HDD pack cover screws a[...]

User ’s Manual 2-9 The Grand T our Front with the display op en This section shows the computer with the display panel open. In order to open the display , lift the display panel up and position it at a comfortable viewing angle for you. Figure 2-6 The front of the computer with th e display panel open Ultra Slim Bay lock screw (u nlock position)[...]

User ’s Manual 2-10 The Grand T our Web Camera Web Camera is a device that allows you to record video or take photographs with you r computer . Y ou can use it for video chatting or video conferences using a communication tool such as Windows Live Messenge r . Ca mera Assistant Sof t ware will help you to add variou s video effects to your video [...]

User ’s Manual 2-1 1 The Grand T our TOSHIBA Assist button Press this button to lau nch the program automatically . When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer and launch the program. TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connec t d isplay button [...]

User ’s Manual 2-12 The Grand T our Micropho ne A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 4, Operating Basics for more informatio n. LCD Sensor switch This switch senses when th e displ ay panel is either closed or opened and activates the Panel Power Of[...]

User ’s Manual 2-13 The Grand T our Indicators This section explains ind icator functions. System indica tors The LED system indicators for specif ic computer operations glow when those operations are in progress. Figure 2-7 System indicators DC IN The DC IN indicator n ormally glows green wh en power is being correctly supplied from the AC power[...]

User ’s Manual 2-14 The Grand T our Keyboard indicators The following figures show the position s of the CAPS LOCK indica tor and the keypad overlay indicators which show the following conditions: ■ When the CAPS LOCK indicator glows, the keyboard will prod uce capitals when any letter is typed. ■ When the Arrow Mode indicator glows, the keyp[...]

User ’s Manual 2-15 The Grand T our Optical disc drives The computer is configured with a DV D Super Multi d rive. Some models are equipped with an optical disc drive. An A T API interface controller is used for CD/DVD-ROM oper ation. When the co mputer is accessing a CD/DVD, an indicator on the drive glows. For information on loadin g and unload[...]

User ’s Manual 2-16 The Grand T our W r it able discs This section describes the types of writ able CD/DVD discs. Check the specifications of your d rive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics . CDs ■ CD-R discs can be written only once. The recorded data can[...]

User ’s Manual 2-17 The Grand T our DVD Supe r Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run ei ther 12 cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor . AC adaptor The AC adaptor can automa ti cally adjust to any voltage ranging from 100 to 240 volts and to a[...]

User ’s Manual 2-18 The Grand T our Figure 2-10 The AC adaptor (3-pin plug) ■ Depending on the model in questio n, either a 2-pin or 3-pin adaptor/power lead will be bund led wi th the computer. ■ Do not use a 3-pin to 2-pin conversion plug. ■ The supplied power co rd conforms to safety rules and regulations in the region the p roduct is bo[...]

User ’s Manual 3-1 Chapter 3 Hardware, Utilities and Options Hardware This section describes the hardware of your computer . The actual specifications ma y vary depending on the model you purchased. Processor CPU The computer is equipped with one of the following Intel ® processors. ■ Intel ® Core TM 2 Duo Processor , which incorporat es a 2M[...]

User ’s Manual 3-2 Hardware, Utilities and Options Memory Power Module s lot 512, 1,024 or 2,048MB memory module can be install e d in the co mp ut er 's memory module slot for a maximum of 4,096MB system memory . Vi de o RAM The amount of Video RAM available is dependent on the comput er's system memory . Star t -> Control Panel -&g[...]

User ’s Manual 3-3 Hardware, Utilities and Options Disks Optical disc drive RTC battery The internal RTC battery backs up the Real T ime Clock (RTC) and calendar . AC adaptor The AC adaptor provides power to the system and recharges the batteries whe n they are low . It comes with a detachable power cord which will either have a 2-pin or 3-pin pl[...]

User ’s Manual 3-4 Hardware, Utilities and Options Display The computer's internal disp lay panel supports high-resolution video graphics and can b e set to a wide range of viewing angl es for maximum comfort and readability . Sound Display panel 12.1" TFT LCD screen, 16 million colors, with a resolution of 1280 horizo ntal x 800 vertic[...]

User ’s Manual 3-5 Hardware, Utilities and Options Multimedia Communications Web Camera Web Camera is a device that allows you to record video or take photographs with your computer . Y ou can use it for video chatting or video conferences using a communicati on tool such as Windows Live Messenger . Camera Assist ant Software will help you to add[...]

User ’s Manual 3-6 Hardware, Utilities and Options Ultra Slim Bay Sp ecial features The following features are eithe r un ique to TOSHIBA computers or are advanced features which ma ke the computer more con venient to use. Access each function using the following proce dures. *1 T o access the Power Options, click Star t -> Control Panel ->[...]

User ’s Manual 3-7 Hardware, Utilities and Options Hot keys Hot keys are specific key combinations that let you quickly change the system configuration directly from the keyboard without running a system program. Display au tom a tic power off *1 This feature auto ma ti ca l l y cut s of f power to the computer's display panel when there is [...]

User ’s Manual 3-8 Hardware, Utilities and Options Low battery automatic Hibernation Mod e *1 When battery power is exhausted to the point th at computer operation cannot be continued, the system automatically ent ers Hibernation Mode and shuts itself down. This can be specified in the Power Options. Heat dispersal *1 T o protect against overheat[...]

User ’s Manual 3-9 Hardware, Utilities and Options T OSHIBA V alue Added Package This section describes the TOSHIBA Component features pre-installed on the computer . TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Button Support This utility controls t he following computer[...]

User ’s Manual 3-10 Hardware, Utilities and Options T OSHIBA T ablet PC Extension This section describe s the pre-insta lled TOSHIBA Component features that come with the computer . T o access th ese components, click Star t -> All Programs -> TOS HI BA . Utilities and Applications This section describes the pre-installed uti lities that co[...]

User ’s Manual 3-1 1 Hardware, Utilities and Options Fingerprint Utility This product ha s a finge rprint utility installed for the purpose of enrolling and recogn izing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard. Just by swiping an enrolled finger again st[...]

User ’s Manual 3-12 Hardware, Utilities and Options TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides access to specific tools, utiliti es and applications that make the use and con figuration of the computer easier . TOSHIBA ConfigFree TO SHIBA ConfigFree is a suite of utilities that improve the ease and control of commun[...]

User ’s Manual 3-13 Hardware, Utilities and Options Window s Mob ility Center This section describ es the Windows Mobility Center . Mobility Center is a utility for accessing several mobile PC settings quickly in one window . A default maximu m of eight tiles are provided by the ope rating system, and the additional three tiles are added to your [...]

User ’s Manual 3-14 Hardware, Utilities and Options Optional devices Optional devices can expand the computer's capabilities and its versatility . This section describes the connection or installation of the fo llowing devices: Cards/memory ■ PC Card ■ Smart Card ■ Bridge medi a slot ■ Secure Digital (SD) Card (SD memory card, SDHC m[...]

User ’s Manual 3-15 Hardware, Utilities and Options PC Card Some models are equipped with a PC Ca rd slot. The computer is equipped with a single PC Card slot that can accommodate a T ype II fo rmat card. Any PC Card that meets industry standards, either manufactured by TOSHIBA or another vendor , can be in stalled as the slot supports 16-bit PC [...]

User ’s Manual 3-16 Hardware, Utilities and Options Removing a PC Card T o remove a PC Card, follow th e step s as det ailed be low: 1. Open the Safely Remove Ha rdware icon on the Windows T askb ar . 2. Point to PC Card and click the left T ouch Pad control button. 3. Press the PC card eject button to extend i t. 4. Press the extended PC Card ej[...]

User ’s Manual 3-17 Hardware, Utilities and Options Inserting a Smart Card The Smart Card slot is located on th e left side of the computer . The Windows hot-install feature allows you to insert a Smart Card while the computer is turned o n. T o install a Smart Card, follow the steps as det ailed below: 1. Insert the Sma r t Card into the Smart C[...]

User ’s Manual 3-18 Hardware, Utilities and Options Removing a Smart Card T o remove a Smart Card, follow the steps as detailed below: 1. Open the Safely Remove Ha rdware icon on the Windows T askb ar . 2. Point to Smart Card and click the left T ouch Pad control bu tton. 3. Grasp the Smart Card and remove it. Figure 3-4 Removing a Smart Card Bri[...]

User ’s Manual 3-19 Hardware, Utilities and Options Figure 3-5 Examples of memory media Memory media This section provides the important safety precautions in order to handle your memory media. Points to note about the SD/SDHC memory card SD/SDHC memory cards compl y with SDMI (Secure Digital Music Initiative), which is a technology adopted to pr[...]

User ’s Manual 3-20 Hardware, Utilities and Options ■ The maximum capacity of SD memo ry cards is 2GB. The maximum capacity of SDHC memory cards is 8GB. Memory media format New medi a cards are f ormatted accordin g to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards. Formatting an S[...]

User ’s Manual 3-21 Hardware, Utilities and Options Memory card care ■ Set the write-protect switch to the lock position, if you do not want to record data. ■ Memory cards have a limited lifespan, so it is important to backup important data. ■ Do not write to a card if the battery p ower is low . Low power could affect writing accuracy . ?[...]

User ’s Manual 3-22 Hardware, Utilities and Options Remo vin g a me mor y med ia The following instru ctions apply to all types of supported media device s. T o remove a memory media, follow the steps as detailed below: 1. Open the Safely Remove Ha rdware icon on the Windows T askb ar . 2. Point to memory media and click the left T ouch Pad contr[...]

User ’s Manual 3-23 Hardware, Utilities and Options Additional mem ory modu le This computer is e quipped with two memory slots; Slot A is beneath the keyboard and Slot B i s in the underside of the computer . Y ou can instal l ad di ti o n al m em ory i nt o th e comput er in order to incr ea se the amount of system memory that is availabl e. Th[...]

User ’s Manual 3-24 Hardware, Utilities and Options Installing a memory module (Slot A) T o install a memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power of f - make sure the Power indicator is off (refer to the T urning off the powe r section in Chapter 1, Getting S t arted if required). 2. Remo[...]

User ’s Manual 3-25 Hardware, Utilities and Options 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. Figure 3-9 Rotate the keyboard 9. Remove the two screws and take off the memory module cover . Figure 3-10 Removing the memory module cover ■ Never allow metal objects, such as screws, staples and [...]

User ’s Manual 3-26 Hardware, Utilities and Options 10. Align the notch of the memory module with tha t of th e memo ry module slot and gently insert the module into the slot at about a 45 de gree angle before holding it down until th e latches on either side snap into place. Figure 3-1 1 Installing the memory module Slot A ■ Never allow metal [...]

User ’s Manual 3-27 Hardware, Utilities and Options 1 1. Screw in the two screws and replace the me mory module cover . Figure 3-12 Seating the memory module cover 12. Insert the tabs on the front of the keybo ard into the corresponding notches on th e computer and pl ace the keyboard d own. 13. Replace the keyboard and secure it using th e two s[...]

User ’s Manual 3-28 Hardware, Utilities and Options Removing a memory module (Slot A) T o remove the memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power of f - make sure the Power indicator is off (refer to the T urning off the powe r section in Chapter 1, Getting S t arted if required). 2. Remov[...]

User ’s Manual 3-29 Hardware, Utilities and Options Installing a memory module (Slot B) T o install a memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power of f - make sure the Power indicator is off (refer to the T urning off the powe r section in Chapter 1, Getting S t arted if required). 2. Remo[...]

User ’s Manual 3-30 Hardware, Utilities and Options 7. Align the notch of the memory modul e with tha t of th e memo ry module slot and gently insert the module into the slot at about a 45 de gree angle before holding it down until th e latches on either side snap into place. Figure 3-16 Seating the memory module Slot B ■ Never allow metal obje[...]

User ’s Manual 3-31 Hardware, Utilities and Options 8. Seat the memory module cover in place and secure it with one scre w . Figure 3-17 Seating the memory module cover 9. Install the battery pa ck - refer to Replacing the battery pack section in Chapter 6, Power and Powe r-Up Modes, if required. 10. Turn your co mp ut er ov er . 1 1. Turn the co[...]

User ’s Manual 3-32 Hardware, Utilities and Options 8. Grasp the memory module by its edges and remove it from the computer . Figure 3-18 Removing the memory module 9. Seat the memory module cover in place and secure it with one scre w . 10. Install the battery p ack - refer to Replacing the battery pack section in Chapter 6, Power and Powe r-Up [...]

User ’s Manual 3-33 Hardware, Utilities and Options HDD Kit (Serial- A T A) An extra hard disk drive expands the fl exibility of your system and allows you to carry your data separately without having to carry the computer . The HDD Kit (Serial-A T A) can either r eplace th e hard di sk drive installed inside the computer or be connected to the U[...]

User ’s Manual 3-34 Hardware, Utilities and Options 8. With the hard disk drive i n a vertical position, lift it straight up a nd away from the connector . Figure 3-20 Removing the hard disk drive pack Installing the hard disk drive pack T o install the hard disk drive pack, follow the steps as detailed below: 1. Move the connector until it is ve[...]

User ’s Manual 3-35 Hardware, Utilities and Options 4. With the connector connected, lower th e hard disk drive down to the storage position. Figure 3-21 Installing the hard disk drive pack 5. Seat the cover and press down until the latches click into pl ace. 6. Secure the cover with two scr ews. 7. T urn your computer over . Never allow metal ob[...]

User ’s Manual 3-36 Hardware, Utilities and Options Ultra Sl im Bay HDD Adaptor Y ou can increa se your comp uter’s data storage capacity by inst alling an additional 80GB hard disk drive in the Ultra Slim Bay . T o install a hard disk drive in the Ultra Slim Bay HDD Adaptor follow the steps below . 1. Slide the lock to the unlock position and [...]

User ’s Manual 3-37 Hardware, Utilities and Options 3. Close the lid and slide the lock to the lock position . Figure 3-24 Closing the lid For details on inserting the Ultra Slim Bay HDD Adaptor in the computer ’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics . External monitor An external analog monitor can be connected to the exte[...]

User ’s Manual 3-38 Hardware, Utilities and Options 4. T urn the computer's power on. When you turn on the power , the computer will automatically recognize the monitor and determine whether it is a color or monochrome device . In the event that you find that there are issues getting an image displayed on the correct monitor , you should con[...]

User ’s Manual 3-39 Hardware, Utilities and Options Connecting the USB floppy diskette drive T o connect the drive, plug the floppy diskette drive’s USB connector into a computer ’s USB port. Figure 3-27 Connecting the U SB floppy diske tte drive Disconnecting the USB floppy diskette drive When you have finished using the USB floppy diskette [...]

User ’s Manual 3-40 Hardware, Utilities and Options USB Sleep and Charge function Y our computer ca n supply USB bus power (DC 5V) to the USB port even when the power of the computer is turned OFF . "Power OFF" includes Sleep Mode, Hibernation Mode or shutdown state. This function can only be used for ports that support the USB Sleep an[...]

User ’s Manual 3-41 Hardware, Utilities and Options USB WakeUp function This function resto r es the comp ut er from Sleep Mode dependi ng on the external devices connected to the USB ports. The "USB W akeUp function" operates under Windows Vista ® OS and it works for all USB ports. i.LINK (I EEE1394) i.LINK (IEEE1394) is us e d for hi[...]

User ’s Manual 3-42 Hardware, Utilities and Options ■ If you connect/disconnect an i.LI NK device to/from another i.LINK device that is currently exchanging data with the computer , data frames might be dropped. ■ Make sure data transfer has ended o r turn off the computer , before you: ■ Connect/disconnect an i.LINK device to/from the co m[...]

User ’s Manual 3-43 Hardware, Utilities and Options TOSHIBA Express Port Replicator In addition to the ports available on the computer , the TOSHIBA Express Port Replicator . The T OSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TO SHIBA Express Port Replicato[...]

User ’s Manual 3-44 Hardware, Utilities and Options Security lock A security locks enable you to ancho r your computer a desk or other heavy object in order to help prevent unautho rized removal or theft. The computer has a security lock slot on its left side into which you can attach one end of the security cable, while the other end attaches to[...]

User ’s Manual 3-45 Hardware, Utilities and Options Optional accessories Y ou are able to add a number of opti ons and accessories in order to ma ke your computer even more powerful and convenient to use . For reference, the following list details some of the items that are avai labl e from your reseller or TOSHIBA dealer: DDR2-400/533 Memory Mod[...]

User ’s Manual 3-46 Hardware, Utilities and Options Ultra Slim B ay options The following module can be installed in the Ultra Slim Bay . All other module is option. TOSHIBA Express Port Replicator The TOSHIBA Express Port Replicator provides the ports available on the computer in a ddition to a digital visual interface (DVI) port, External monit[...]

User ’s Manual 4-1 Chapter 4 Operating Basics This chapter describes the basic operations of your computer , highlights the precautions that should be taken when using it. Pointing Devices The pointing devices of this computer vary from model to model. ■ Digitizer screen model: The T ouch Pad and the T ablet PC Pen which comes with the computer[...]

User ’s Manual 4-2 Operating Basics Using the T ouch Pad T o use the T ouch Pad, simply touch and move your finge rtip across it in the direction you want the on-screen pointer to go. Figure 4-1 T ouch Pad and T ouch Pad contr ol buttons The two butt on s be low the T ouch Pad are used like th e bu t tons on a standard mouse - press the left butt[...]

User ’s Manual 4-3 Operating Basics Using the T ablet PC Pen and Reserve Pe n Y ou can use the T ablet PC Pen to execute acti ons and enter data. Hold the T ablet PC Pen in a na tural positio n and tap, press or trace on the screen lightly . Some computers in the series are equipped with a T ablet PC Pen and a Reserve Pen. Figure 4-2 The T ablet [...]

User ’s Manual 4-4 Operating Basics Observe the following precautions on the hand ling of the T ablet PC Pen. ■ In order to avoid damages to the di splay screen, please refrain from doing anything other than the specif ie d operation methods. Fail ure to do so could cause a malfunction or characte ristic deteri oration. ■ Do not tap or press [...]

User ’s Manual 4-5 Operating Basics Removing the T ablet PC Pen T o remove the T ablet PC Pen, follow the steps as described below: 1. Push the T ablet PC Pen in the T ablet PC Pen slot, so that it protrudes slightly . 2. Pull the T ablet PC Pen to remove it from the T ablet PC Pen slot. Figure 4-3 Removing the T ablet PC Pen Inserting the T able[...]

User ’s Manual 4-6 Operating Basics Double tap Lightly tap the tip of the T a blet PC Pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left touch p ad control button. Press and hold T ouch the tip of the T ablet PC Pen to the d isplay screen and ho ld it there to display a pop-up [...]

User ’s Manual 4-7 Operating Basics Removing the Reserve Pen case T o remove the Reserve Pen case, follow the steps as detailed below: 1. Save your work. 2. T urn the computer ’s power off - ensure that the Power indicator is off. 3. Remove all cables and peri pherals that are connected to the computer . 4. Close the displ ay panel and turn the[...]

User ’s Manual 4-8 Operating Basics S toring and Removing the Reserve Pen from the Res erve Pen case Follow the procedures b elow to remove the Reserve Pen from the Rese rve Pen case. Removing the Reserve Pen from the Reserve Pen case 1. Lift the Reserve Pen up from the Reserve Pen case by its end. Figure 4-8 Removing the Reserve Pen from the Res[...]

User ’s Manual 4-9 Operating Basics Using the T ablet mode This section explains T ablet mode functions and use. Operating the com puter in T ablet mode When operating the computer in T ablet mode, follow the instructions below . Figure 4-10 Operating the computer in T ablet mode (using a T ablet PC Pen) ■ Hold the computer firmly on your forea[...]

User ’s Manual 4-10 Operating Basics ■ The function of the display screen varies from model to model. ■ Digitizer screen model: Please use the T ablet PC Pen to operate, which comes with the computer . Please carefully observe the following items in order to avoid damaging the di splay screen. Incorrec t use could cause the screen to be scrat[...]

User ’s Manual 4-1 1 Operating Basics ■ The display panel works as a touch s ensitive digitizer screen. However , the outer edges of the screen may be le ss sensitive. Please keep the T ablet PC Pen or your fing er inside the display area when you use it near the edges of the display panel. The p osition of the pen may not be recognized if you [...]

User ’s Manual 4-12 Operating Basics Changing to the T ablet mode T o change from Laptop mode to the T a blet mode, follow the instruction s below . 1. Open the display panel to the upright position. Figure 4-12 Changing to the T ablet mode (1) When rotating the display panel, be sure to keep the display panel at a 90-degree angle to the keyboard[...]

User ’s Manual 4-13 Operating Basics 2. Rotate the display panel clockwise slowly . Figure 4-13 Changing to the T ablet mode (2) 3. Close the display panel slowly with display surface facing upwards. Figure 4-14 Changing to the T ablet mode (3) ■ When rotating display panel of your computer , be sure to slowly tu rn it in the proper direction, [...]

User ’s Manual 4-14 Operating Basics Changing to the Lapto p m ode T o change the operating mode to the Laptop mode, foll ow the steps as detailed below: 1. Raise the display to the upright position carefully . 2. Rotate the display counter-clockwise slowly . 3. Close the display . Changing the screen orient ation The orientation of the computer [...]

User ’s Manual 4-15 Operating Basics Method 1: Changing the screen orientation using T OSHIBA Accelerometer Utilities and TOSHIBA Rotation Utility When the TOSHIBA Accelerometer Utilities and TOSHIBA Rot ation Utility are running, changes in the orientati on of the top and bot tom of th e scre en is automatically recognized by pressi ng ESC/Rotat[...]

User ’s Manual 4-16 Operating Basics 5. Select a screen orientation from the Orientation pull down menu and change the screen. Using Acce lerometer Utilities It is safer if you hold the computer with both han ds horizontally as shown in the below example. Figure 4-16 Shake the computer Y ou can se t the orie ntation of the desktop screen just aft[...]

User ’s Manual 4-17 Operating Basics Using the Fingerprint Sensor This product has a fingerp rint uti lity installed for the purpose of en rolli ng and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authenticati on feature, it is no longer nece ssa ry to input the password from the keyboard. Fingerprint feature en[...]

User ’s Manual 4-18 Operating Basics The following illustration s show the recommended way to swipe your finger over the fingerprint sensor . Figure 4-17 Swipe the finger Sample. 2) When swiping th e thumb Sample. 1) When swiping the index finger Sensor Sensor ■ Avoid swiping with your finger stiff or pressed too hard onto the sensor , and take[...]

User ’s Manual 4-19 Operating Basics Point s to note abou t the Fingerprint Sensor Please be aware of the following consideratio ns when using the fingerprint sensor . A fail ure to follow these guidel i nes might result in damage to the sensor , se nsor fa ilure, fingerprint recogniti on problems or a lower fingerprint recognition success ra te.[...]

User ’s Manual 4-20 Operating Basics ■ Check the position and speed at which you swipe your fing er across the sensor - plea se refer to th e precedin g drawin g. ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However , there may be instances where certain users are unabl e to register thei r finge[...]

User ’s Manual 4-21 Operating Basics 6. Register your fingerprint on the Fingerprint Image Capture screen. Let the computer read the finger to be registered 3 ti me s. An image of your fingerprint will be shown on the screen each time the fingerprin t is successfully read. Once the fingerprint is successfu lly read for the third time, th e messag[...]

User ’s Manual 4-22 Operating Basics In use, please be aware of the follo win g limitations of the fingerprint sensor: ■ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration . ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However[...]

User ’s Manual 4-23 Operating Basics Fingerprint Pre-OS Au then tication General The fingerprint auth entication system can be used to replace the keyboard based password authentication system th at is used when the computer is turned on. If you do not want to use the fingerprint auth entication system for password authentication while bo oti ng [...]

User ’s Manual 4-24 Operating Basics Fingerprint Single-Swipe Sign On Feature General This is a feature that allow s the user to complete the authentica tion for both the User/BIOS Password (and, if ap plicable, the HDD(Hard Disk Drive) Password) and logging onto Windows using only one fingerprint authentication when booting up. It is necessary t[...]

User ’s Manual 4-25 Operating Basics We b C a m e r a Web Camera is a device that allows you to record video or take photographs with your compute r . Y ou can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger . Camera Assist ant Sof tware will help you to add variou s video effects to your v[...]

User ’s Manual 4-26 Operating Basics Changing Ultra Sli m Bay modules This section explains how to change modules in the Ultra Slim Bay . The illustrations show replacement of the opti cal disc drive with the Ultra Slim Bay HDD Adaptor . Removing a m odu le T o remove the optical disc drive, follow the steps as described below: 1. Save your work.[...]

User ’s Manual 4-27 Operating Basics 8. Slide the Ultra Slim Bay la tch to th e unlock position. 9. Grasp the optical disc drive and slide it ou t. Figure 4-19 Removing the optical disc drive Inserting a m odule T o insert the Ultra Slim Bay HDD Adaptor , follow the steps as described below: 1. Insert the Ultra Slim Bay HDD Adap tor in the comput[...]

User ’s Manual 4-28 Operating Basics Ultra Slim Bay Case The DVD Super Multi drive is equippe d with an Ultra Slim Ba y Case. This section explains how to remove and in stall the DVD Super Multi drive unit. Removing a unit T o remove the DVD Super Multi drive unit from the Ultra Slim Bay Case, follow the steps as described below: 1. Slide the Ult[...]

User ’s Manual 4-29 Operating Basics Using optical disc drives The full-si ze drive pr ovides high -performanc e execution of CD/DVD-R OM- based programs. Y ou can run eith er 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor . An A T API inte rface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/[...]

User ’s Manual 4-30 Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray . Figure 4-24 Inserting a CD/DVD 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD shou ld lie below the top of the spindl e, flush with the spindle base. Laser lens When the disc tray is ful ly opened, the edge of the [...]

User ’s Manual 4-31 Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. Figure 4-25 Closing the CD/DVD disc tray Removing discs T o remove the CD/DVD, follow the steps as detailed below: 1. T o pop the disc tray partially open, press the e ject button. Gently pull the disc tray out until it is[...]

User ’s Manual 4-32 Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. Optical Drive Auto Loc k This function automat ically locks the optical disc drive eject bu tton if the computer detects any vibration or other shocks while running on the battery . This function prevents the disc tray fro[...]

User ’s Manual 4-33 Operating Basics How to rem ove CD/D V D when the disc tray w ill n ot open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eje c t bu [...]

User ’s Manual 4-34 Operating Basics Import ant message Before you write or rewrite to an y of the media supported by the DVD Super Multi Drive, please read and follow all of the setup and opera ting instructions in this section. If you fail to do so, you may find that the DVD Super Multi drive may not function properly , and you may fai l to wri[...]

User ’s Manual 4-35 Operating Basics CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORA TION RICOH Co., Lt d. CD-RW : (Ultra-Speed) MITSUBISHI CHEMICAL CORPORA TION DVD-R: DVD Sp ec i fications for Re cordab le Disc fo r General V ersion 2.0 T AIYO YUDEN CO., L T D. Matsushita Electric Industrial Co., Ltd DVD-R (Dual Layer): MITSUBIS[...]

User ’s Manual 4-36 Operating Basics ■ If the disc is poor in quality , or is dirty or damaged, wr iting or rewriting errors may be noted - ensure that you check a ll discs for dirt or damage before you use them. ■ The actual number of rewrites to CD-RW , DVD-RW , DVD+RW or DVD- RAM media will be affected by the quality of the disc itself and[...]

User ’s Manual 4-37 Operating Basics ■ Before you enter e ither Sleep Mod e or Hibernation Mode, take care to ensure that any DVD -RAM writing has been completed. In this instance, writing is finished if you can eject the DVD-RAM media. ■ Be sure to close all other software programs except for the writing software itself. ■ Do not run softw[...]

User ’s Manual 4-38 Operating Basics ■ Make sure tha t the writ e/rewrit e operation is completed before going into either Sleep Mode or Hiber nation Mode (writing is completed if you can remove an optical media on the DVD Super Multi drive). ■ If the media is of poo r quality , or is dirty o r damaged, writing or rewriting errors may occur .[...]

User ’s Manual 4-39 Operating Basics ■ TOSHIBA Disc Creator does not supp ort recording to DVD-RAM discs - to achieve this you should use Windows Explorer or anoth er similar utility . ■ When you back up a DVD disc, be sure that the source drive supports recording to DVD-R, DVD-R (Dual Layer), DVD-RW , DVD+R, DVD+R (Double Layer) or D V D +R [...]

User ’s Manual 4-40 Operating Basics Media care This section provides tips on protecting data stored on your CD's, DVD's and floppy diskettes. Handle your media with care. Following th e simple precautions listed be low will increase th e lifetime of your media and protect the data stored on it. CD/DVDs 1. S tore your CD's and DVD&[...]

User ’s Manual 4-41 Operating Basics 8. Data may be lost if the floppy diskett e is twisted, bent, or exposed to direct sunlight , extreme hea t or co ld . 9. Do not place heavy objects on your floppy diskettes. 10. Do not eat, smoke, or use items such as erasers near your floppy diskettes as foreign particles inside the jacket of the floppy di s[...]

User ’s Manual 4-42 Operating Basics Audio Enhancement s In order to apply the soun d effects for your current speaker , follow the steps below . 1. Right click on the speaker icon on the T askbar , and select Playback Devices from the sub menu. 2. Select Speakers , and click Properties . 3. On the Enhancement s tab select the sound effect s you [...]

User ’s Manual 4-43 Operating Basics TO SHIBA M ic Effect TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual commu nication via the Internet Protocol or Local Area Network. If you wish to communicat e with someone on your computer , you can use a messenger application. However , with such an application, you would he[...]

User ’s Manual 4-44 Operating Basics Region selectio n T elecommunication regulations vary from one regio n to another , so you will need to make sure the internal modem’s settings are correct fo r the region in which it will be used. T o select a region, follow the steps as detailed below: 1. Click Start -> All Programs -> TO SH IB A -&g[...]

User ’s Manual 4-45 Operating Basics Location list for region selection. Displays a sub-menu appears which details location information. Open dialog box, if the modem and T elephony Current Location region code do not match. Displays a warning if the current settings for both region cod e and telephony location are di fferent. Modem Sele ction If[...]

User ’s Manual 4-46 Operating Basics 2. Plug the other end of the modular cable into a te lephone jack. Figure 4-28 Connecting the internal modem Disconnecting the m odular cable T o disconnect the modular cable, follow the steps as detailed below: 1. Pinch the lever on the plug in the telepho ne ja ck and pull it out from within the co nne ctor [...]

User ’s Manual 4-47 Operating Basics Wireless com munications The computer ’s wireless communication function supports both Wireless LAN and Bluetooth devices. Only some models are equipped wit h both Wireless LAN and Bluetooth functions. Wireless LAN The Wireless LAN is compatible wit h other LAN systems based on Direct Sequence S pread S pect[...]

User ’s Manual 4-48 Operating Basics ■ Wired Equivalent Privacy (WEP) data encryption based on an 128-bit encryption algorithm ■ Wi-Fi Protected Access (WP A) Setting 1. Please make sure that the Wireless Communication S witch is turned on. 2. Click Star t and then click Connect T o to display Connect to a network window . 3. Click Set up a c[...]

User ’s Manual 4-49 Operating Basics Radio links Y ou can easily establish links between two or more devices, with these links being maintained even if the devi ces are not within a line-of-sight of each othe r . Security T wo advanced security mechan is ms ensure a high le vel of security: ■ Authentication prevents access to critical data and [...]

User ’s Manual 4-50 Operating Basics Wireless com munication Indicator The wireless communication indicator shows the status of the computer's wireless com mun ication func tions. If you used the T askba r to disable the wireless LAN, restar t the computer o r perform the following procedure to re-enab le it: Star t -> Control Panel ->[...]

User ’s Manual 4-51 Operating Basics Connecting the LAN cable T o connect the LAN cable, foll ow the steps as detailed below: 1. T urn off the power to the computer and to all external devices connected to the computer . 2. Plug one end of the cable into t he LAN jack. Press gently until yo u hear the latch click into place. Figure 4-29 Connectin[...]

User ’s Manual 4-52 Operating Basics Disconnecting the LAN cab le T o disconnect the LAN cable, follow the steps as det ailed below: 1. Pinch the lever on the connector in the computer ’s LAN jack and pull out the connector . 2. Disconnect th e cable from the L AN hub or router in the same manner. Check with your LAN administrator and hardware [...]

User ’s Manual 4-53 Operating Basics ■ Disconnect the AC adaptor and all peripherals before moving the computer . ■ Close the display panel. ■ Do not pick up the comput er by its displ ay p anel. ■ Before carrying your computer , shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may r[...]

User ’s Manual 4-54 Operating Basics T askbar icon TOSHIBA HDD Protection Properties Y ou can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window . T o open the window , click Star t -> All Programs -> TOS HI BA -> Utilities -> HDD Protection Settings . The window can also be started from t[...]

User ’s Manual 4-55 Operating Basics Det ails T o open the Details window , clic k the Setup Detail button in the TOSHIBA HDD Protection Properties window . Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Dete ction assumes that the computer will be carried and sets the detection level to the maximum fo[...]

User ’s Manual 5-1 Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhance d keyboard functions can be performed on the computer . The number of keys available on your keyboard wil l depend on which country/region your co[...]

User ’s Manual 5-2 The Keyboard Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your key board - these keys function differentl y from other keys. F1 through F12 are called functi on keys because they execute programmed functions when pr essed and , when used in combinatio[...]

User ’s Manual 5-3 The Keyboard Press FN + F10 or FN + F1 1 to access the computer's integrated keypad. When activated, the keys with grey ma rkings on their bottom e dge become either numeric keypad keys ( FN + F1 1 ) or cursor control keys ( FN + F10 ). Please refer to the Keypad overlay section in this chapter for more information on how [...]

User ’s Manual 5-4 The Keyboard Sleep : Pressing FN + F3 switches the system to Sleep Mode. Hibernate : Pressing FN + F4 switches the system to Hibernation Mode. Output : Pressing FN + F5 changes the active display device. Brightness Down : Pressing FN + F6 decreases the computer's display panel brightness in individual steps. Brightness Up [...]

User ’s Manual 5-5 The Keyboard ODD: Pressing FN + Ta b turns the power of the optical disc drive on/off or ejects the disc tray . TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes wi thin one of the supported applica tion windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges t[...]

User ’s Manual 5-6 The Keyboard Keyp ad overlay Y our computer's keyboa rd does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyb oard with the relevant keys havi ng grey letters at their front edge. The overlay provides the same functions as the nume[...]

User ’s Manual 5-7 The Keyboard T emporarily using normal keyboard (ove rlay on) While using the overlay , yo u can te mporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold down FN key and press any other key - this key will operate as if the overlay were off. 2. T ype upp er-case characters by holding dow[...]

User ’s Manual 6-1 Chapter 6 Power and Power-Up Modes The computer's p ower resources in clude the AC ad aptor , battery pack and any internal batteries. This chapter provides details on making the most effective use of the se resources , and includ es informati on on charging and changing batteri es, tips for saving ba ttery power , and inf[...]

User ’s Manual 6-2 Power and Power-Up Modes T a ble 6-1 Power conditions continued Power on Power off (no operation) AC adaptor connected 2nd battery fully charged • Operates • No charge • LED: 2nd battery green DC IN green • No charge • LED: 2nd battery green DC IN green 2nd battery par ti al ly charged or no charge • Operates • Ch[...]

User ’s Manual 6-3 Power and Power-Up Modes T a ble 6-1 Power conditions continued 1 Wh en the Slice Expansion Battery is not charging. * 2 W hen the main battery is not charging. * 3 For the computer to shut down in Hibernation Mode, the Hib ernation feature must be enabled in Power Op tions. If a ma in ba ttery and a Slice Expans ion Battery ar[...]

User ’s Manual 6-4 Power and Power-Up Modes Monitoring of power condition As shown in the below table, the Battery , 2nd battery , DC IN and Power indicators on the system indicator al ert you to the computer’s operating capability and battery charge status. Battery indicator Check the Batte ry indicator to determine the st atus of the main bat[...]

User ’s Manual 6-5 Power and Power-Up Modes Power i ndica tor Check the Power indicator to determine the pow er status of the computer - the following indicator conditions shou ld be no ted: Battery This section explai ns battery types, use, recharging me thods and handling. Battery types The computer has three diff erent types of batteries. Batt[...]

User ’s Manual 6-6 Power and Power-Up Modes Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provid es power for the inte rnal real time clock and calendar functi on and also maintains the system configuration while the computer is turned off. If the RTC battery becomes completely discharged, the syst em will lose this in formation[...]

User ’s Manual 6-7 Power and Power-Up Modes Charging the batte ries When the power in the battery pack becomes low , the Battery indicator will flash orange to indicate that only a fe w minutes of batte ry power remain. If you continue to u se the computer w hile the Ba ttery indicator flashes, the computer will enable Hibernation Mode so that yo[...]

User ’s Manual 6-8 Power and Power-Up Modes Battery charging notice The battery may not begin charging immediately under the following conditions: ■ The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). T o ensure the battery charges to its full capacity , you should charge it at room temperatur e o[...]

User ’s Manual 6-9 Power and Power-Up Modes Maximizing battery op erating time A battery's usefulness depends on how long it can su pply power on a single charge, while how long the c harg e lasts in a battery depends on: ■ Processor speed ■ Screen bright ness ■ System Sleep Mode ■ System Hibernation Mode ■ Display power off period[...]

User ’s Manual 6-10 Power and Power-Up Modes Extending battery life T o maximize the life of your battery packs: ■ At least once a month, disconnect t he computer from a power source and operate it on battery power unt il the battery pack fully discharges. Before doing so, fo llow the steps as detailed below . ■ If you have extra battery p ac[...]

User ’s Manual 6-1 1 Power and Power-Up Modes Removing the battery pa ck T o remove a discharged battery , follow the steps as detailed below: 1. Save your work. 2. T urn the computer's power off - ensure that the Power indicator is off. 3. Remove all cables and peri pherals that are connected to the computer . 4. Close the displ ay panel an[...]

User ’s Manual 6-12 Power and Power-Up Modes Installing the battery pack T o install a battery p ack, follow the steps as detailed below: 1. Insert the battery pack as far as it will go into the computer (1). 2. Ensure that the battery pack is secu rely in place and the battery lock (2) is in its ( ) position. Figure 6-3 Securing the battery pack[...]

User ’s Manual 6-13 Power and Power-Up Modes 3. Remove the pr otective cap from the Slice Expansion Battery . 4. Open latches on the Slice Expansio n Battery and fit a tab on the battery into the docking port on the und erside of the computer . Figure 6-4 Seating the Slice Expansion Battery 5. Close the latches to secure the Slice Expansion Batte[...]

User ’s Manual 6-14 Power and Power-Up Modes 5. Open the release latches in the di rection of the arrows. Figure 6-6 Releasing the latches 6. Lift off the Slice Exp ansion Battery . Figure 6-7 Removing the Slice Expansion Battery 7. Be sure to replace the protective cap befo re storing the Sli ce Expansion Battery . T O SHIBA Passwo rd Utility Th[...]

User ’s Manual 6-15 Power and Power-Up Modes User Password T o start the utility , point to or click the following items: St art -> All Programs -> TOSHIBA -> Utilities ->Password Utility The User Password dialog box contains two main fields: User Password and User Token . User authentication may be required to valid ate user rights w[...]

User ’s Manual 6-16 Power and Power-Up Modes User T oken field ■ Create (button) Y ou can use an SD Card token, inst ead of entering the password. After you have registered a password, insert an SD Card in SD Card slot and click Create . Y ou can use an SD Card of any capacity , but it must be formatted correctly . If an unformat te d ca rd or [...]

User ’s Manual 6-17 Power and Power-Up Modes Supervisor Password If you set a Supervisor Password, so me functions might be restricted when a user logs on wit h the U s er Pa ssw or d. T o set a Supervisor Passwo r d , execute the file TO SPU.EXE. The file is located at: C:Program FilesToshibaPas swordUtilityTOSPU.exe This utility lets you do[...]

User ’s Manual 6-18 Power and Power-Up Modes T ablet mode Enter your password by tapping the on-screen keyboard using the T ablet PC Pen or your finger . On-screen keyboard can not be used in Display screen model. Figure 6-8 On-screen keyboard ■ The beep sounds when tapping the on -screen keyboard with the T ablet PC Pen or your finger . An * ([...]

User ’s Manual 6-19 Power and Power-Up Modes Hot keys Y ou can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter Hibernation Mode - please refer to Chapter 5, The Keyboard for further details. Panel power on/off Y ou can set up your computer so that power is turned off automatically when you close the display panel, and turned on ag[...]

User ’s Manual 7-1 Chapter 7 HW Setup & BIOS Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer , and provides information on settings for various functions. Accessing HW Set u p T o run the HW Setup prog ram, click Start -> All Programs -> TO SH IB A -> Utilities -> HWSetup . HW Setup w[...]

User ’s Manual 7-2 HW Setup & BIOS Setup General This window displays the BIOS version and contains two buttons : Default and About . Setup This field displays the installed BIOS version and date. Display This tab lets you customize your computer’s display settings for either the internal display or an external monitor . Power On Display Th[...]

User ’s Manual 7-3 HW Setup & BIOS Setup Boot Priority Boot Priority O ptions This tab allows you to select the pr iority for booting the computer - the following settings are available: Y ou can ov erride the settings and manually select a bo ot device by pressing one of the following keys while the compute r is booting: * 1 The floppy diske[...]

User ’s Manual 7-4 HW Setup & BIOS Setup T o change the boot drive, follow the steps below . 1. Hold down F12 and boot the computer . 2. The following menu will be displaye d with th e following icons: Built-in hard disk drive, Ultra Slim Bay hard disk drive, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. 3. Use the left/rig[...]

User ’s Manual 7-5 HW Setup & BIOS Setup USB Memory BIOS Support T yp e This option allows you to set the type of the USB memory to be used as a startup device. Keyboard Wa ke -up on Keyb oard When this feature is enabl ed, and the co mputer is in Slee p Mode, you can turn on the system by pressing any ke y . Howe ver , please be awa re that [...]

User ’s Manual 7-6 HW Setup & BIOS Setup CPU This function allows yo u to set the processor's operating mode. Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor - the following settings are availabl e: LAN Wake-up on LAN This feature lets the computer ’s power be turned o[...]

User ’s Manual 7-7 HW Setup & BIOS Setup Built-in LA N This feature enables or disables th e Built-in LAN. Device Config Device Configuratio n This option allows you to set how th e computer's hardware devic es will be configured. USB USB KB/Mouse Legacy Emulat ion Y ou can u se this option to enable or disab le USB keyboard/mouse l egac[...]

User ’s Manual 7-8 HW Setup & BIOS Setup BIOS Setup Program Settings for some features are carried out in the BIOS setup program. St arting and Ending the BIOS Setup Program S tarting the BIOS Setup Program 1. T urn on the computer while pressing the ESC key - if the Password = prompt is di splayed, en ter either the Supervisor Password, if o[...]

User ’s Manual 7-9 HW Setup & BIOS Setup Ending the BIOS Setup Program Halfway The configuration settings ca n be terminated hal fway without saving any of the changes made by following the steps detailed below: 1. Press the ESC key - the Exit without saving? (Y/N) prompt to be displayed at the bo ttom of the screen. 2. Press the Y key - the [...]

User ’s Manual 7-10 HW Setup & BIOS Setup Virtua liza tio n T ec hnol ogy Virtualization T echnology sets enable or disable of the Intel ® Virtualization T echnology installed in the CPU. Intel ® Virtualization T echnology is the technique that allows one machine to operate as multiple virtual machines. The Disabled command does not allow u[...]

User ’s Manual 7-1 1 HW Setup & BIOS Setup Auto Power On This is a functi on for automati cal l y tur ning on the compu ter . This item shows the current Auto Power On setting. When Alarm Time, W ake-u p on LAN, or Critic al Battery W ake-up are Enabled, Auto Power On is al so Enabled. Alarm T ime, W ake-up on LAN, on Batt ery and Critical Ba[...]

User ’s Manual 7-12 HW Setup & BIOS Setup Security controller Please note that the security controller se ttings are available on the second page of the BIOS setup application. TPM This setting enables or disab les th e computer's T rusted Platform Module (TPM) security controller . Clear TPM Owner This setting is used to erase th e data[...]

User ’s Manual 7-13 HW Setup & BIOS Setup SA T A Controller M ode This feature sets the SA T A Controller Mode. USB Sleep and Charge functi on This section describes the settings for "USB Sleep and Charge function". For more inform ation, plea se refer to the USB Sleep and Charge function section in Chapter 3, Hard ware, Utilities a[...]

User ’s Manual 8-1 Chapter 8 T roubleshooting TOSHIBA have designed this computer for durability , however , should problems occur you are able to use the procedures detailed in this chapter to help determi ne the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems fr om occurring in [...]

User ’s Manual 8-2 T roubleshooting Preliminary c hecklist Y ou should always consider the simplest solution first - the items de tailed in this checklist are easy to fix and yet can cause what appears to be a serious problem : ■ Make sure you turn on all peripheral devices before you turn on the computer - this i ncludes your printer and any o[...]

User ’s Manual 8-3 T roubleshooting ■ Do you hear any beeps, if so how many , are they long or short and are they high pitched or low pitched? In addition, is the computer making any unusual noise s? Write down what you hear. Record your observations so you can describe them in detail to your reseller , dealer or service provider . Hardware and[...]

User ’s Manual 8-4 T roubleshooting System start- up When the computer does not start pr op erly , check the following items: ■ Self T est ■ Power Sources ■ Power-on Password Self test While booting up the computer , self te st is executed aut omatically and the TOSHIBA logo is displayed on the screen. This message remains on the screen for[...]

User ’s Manual 8-5 T roubleshooting AC power If you have trouble turning on the comp u ter with the AC adaptor connected you should check the status of the DC IN indicator . Please refer to Chapter 6, Power and Power-Up Modes for further information. Battery If you suspect a problem with the battery , you should check the status of the DC IN indi[...]

User ’s Manual 8-6 T roubleshooting Battery doesn’t charge when the AC adaptor is attached ( Battery indicator does not glow orange). If the battery is completely di scharged, it will no t begin charging immediately , in these insta nces you should wait a few minutes befor e trying agai n. If the battery still does not cha rge, you should check[...]

User ’s Manual 8-7 T roubleshooting Real Time Clock Password Keyboard Keyboard problems can be caused by the setup and conf iguratio n of the computer - please refer to Chapter 5, The Keyboard for further information. Problem Pro cedure The following message is Displayed on the screen: RTC battery is low or CMOS checksum is inconsistent. Press [F[...]

User ’s Manual 8-8 T roubleshooting Internal display p anel Apparent computer's display pane l problems may be related to the computer's setup and config uration - please refe r to Chapter 7, HW Setup & BIOS Setup , for further information. Hard disk drive Problem Pro cedure No display Press the FN + F5 hot keys to adjust the displa[...]

User ’s Manual 8-9 T roubleshooting DVD Supe r Multi drive For more inform ation, refer to Chapter 4, Operating Basics . Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utili ty to check the condition of your files and the hard disk drive. Please refer to the operating[...]

User ’s Manual 8-10 T roubleshooting USB floppy diskette drive For further information, please refer to Chapter 3, Hardware, Utilities and Options . Check the type of CD/D VD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD - RO M : CD-DA, CD-T ext, Photo CD TM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form[...]

User ’s Manual 8-1 1 T roubleshooting PC Card For further information, please refer to Chapter 3, Hardware, Utilities and Options . Smart Card For further information, please refer to Chapter 3, Hardware, Utilities and Options . SD/SDHC Card For further information, please refer to Chapter 3, Hardware, Utilities and Options . Problem Pro cedure P[...]

User ’s Manual 8-12 T roubleshooting Memory S t ick For further information, please refer to Chapter 3, Hardware, Utilities and Options . xD picture card For further information, please refer to Chapter 3, Hardware, Utilities and Options . Y ou cannot rea d a file Check to ensure the req uired file is actually on the SD/SDHC Card that is inserted[...]

User ’s Manual 8-13 T roubleshooting MultiMediaC ard For further information, please refer to Chapter 3, Hardware, Utilities and Options . Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter , and the documentation supplied with your mouse. T ouch Pad Y ou cannot rea d a file Check to[...]

User ’s Manual 8-14 T roubleshooting Double-tapping does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility . 1. T o access this utility , click Start -> Control Panel -> Hardware and Sou nd -> Mouse icon. 2. Withi n th e Mo us e Properties wi n do w , click the Bu[...]

User ’s Manual 8-15 T roubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation In this inst ance the system might be busy - T ry moving the mouse again after waiting a short while. Remove the mouse from the comp uter and then reconnect it to a free USB port it in order to ensure it is firmly attached. Doubl[...]

User ’s Manual 8-16 T roubleshooting Fingerprint Sensor Problem Pro cedure Readin g of the fingerprint was not successful. In this instance you should try the fingerprint reading operation agai n using the correct finger position - plea se refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics for further information. Alternativ el [...]

User ’s Manual 8-17 T roubleshooting USB device In addition to the information in this section, p lease also refer to the documentation supplied with yo ur USB device. USB Sleep and Charge function Problem Procedure USB device does not work Remove the USB device from the computer and then reconnect it to a free port it in order to ensure it is fi[...]

User ’s Manual 8-18 T roubleshooting Problem Pro cedure Some external devices may not be able to use the "USB Sleep and Charge function". In this case, please try one or more of the following methods. ■ Change a mode setting of [Enabled ] by the BIOS Setup. ■ T urn OFF the computer while external devices are connected. ■ Connect e[...]

User ’s Manual 8-19 T roubleshooting Additional mem ory modu le Please also refer to Chapter 3, Hardware, Utilities and Options , for further information on installing and removing memory modules. Problem Pro cedure The "USB W akeUp function" does not work. When "USB Sleep and C harge function" is set to [Enabled] in the BIOS [...]

User ’s Manual 8-20 T roubleshooting Sound system In addition to the information in this section, p lease also refer to the documentation supplied with your a udio device. Problem Pro cedure No sound is heard Adjust the volume contro l dial. Check the software volume settings. Please check to see if Mute is turned to Of f Check to make sure the h[...]

User ’s Manual 8-21 T roubleshooting External monitor Please also refer to Chapter 3, Hardware, Utilities and Options , and to the documentation supplied with your monitor for further information. Problem Pro cedure Monitor does not turn on After co nfirming that the monitor's power switch is on, you should check the conn ections to make sur[...]

User ’s Manual 8-22 T roubleshooting i.LINK (IEEE1394) devi ce Modem For additional informati on, please also refer to Append ix C, A T Commands and Appendix D, S-registers . Problem Pro cedure i.LINK device does n ot function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on.[...]

User ’s Manual 8-23 T roubleshooting LAN Communication is cut off unexpectedly The computer will automa tically cut off communication when co nnection with the carrier is not successful for a set time interval - try lengthening this time inte rval within your communication application. A CONNECT display is quickly replaced by NO CARRIER Ensure th[...]

User ’s Manual 8-24 T roubleshooting Wireless LAN If the following procedures do not re store LAN access, consult your LAN administrator . For more information on wireless communication, refer to Chapter 4, Operating Basics . Bluetooth For further information on Bluetooth wire less commu nication, please refer to Chapter 4, Operating Basics . Pro[...]

User ’s Manual 8-25 T roubleshooting Recover y Discs Disposing of the com puter and the co mp uter's batteries ■ Discard this compu ter in acco rdance with appli cable laws and regulations. For further information, cont act y our local government. ■ This computer contains rechargeable batteries. After repeated use, the batteries will fin[...]

User ’s Manual 8-26 T roubleshooting ■ Use a proven specia lized utility to overwri te all data ■ T ake the hard disk drive to a professional deletion service All data deletion costs will be b orne by you. T OSHIBA sup port If you require any additional help using your compu te r or if you are having problems operating the computer, you may n[...]

User ’s Manual 8-27 T roubleshooting Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra T echnopark Singapore 1 19968 Spai n TOSHIBA Information Systems, ESP AÑA Parque Empresa ri a l Sa n Fe rn an d o Edificio Europa, l a Planta, Escalera A 28830 Madrid United S t ates o f America TOSHIBA America Information Systems, Inc[...]

User ’s Manual A-1 Appendix A S pecifications This appendix summarizes the computer ’s technical specifications. Physical Dimensions This section summarizes th e computer ’s technical specifications. Physical Dimensions Environmental Requirements Weight (typical)* 2.0 kilograms, configured with: 12.1"WXGA, 1,024 MB RAM, 80GB HDD, DVD Sup[...]

User ’s Manual A-2 S pecifications Power Requirements Built-in Mod em Wet-bulb temperature 26°C maximum Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 V DC 5.0 amperes This information is appl icable to the mo[...]

User ’s Manual A-3 S pecifications Communication speed Data transmission and rece ption 300/1200/2400/4800/7200 /9 600/12000/14400 /16 800/19200/21600/24000 /26400/28800/3 1200/33 600 bps Data reception only with V .90 28000/29333/30666/320 00/33333/34666/36000/ 37333/38666/40000/413 33/42666/44000/45333/ 46666/48000/49333/506 66/52000/53333/5466[...]

User ’s Manual B-1 Appendix B Display Controller and V ideo mode Display controller The display controller in te rprets software commands into hardware commands that turn particular parts on the screen on or of f. The display controller al so controls the video mode and uses industry standard rules to govern the screen resolution and the maximum [...]

User ’s Manual C-1 Appendix C A T Commands In most cases, you will not need to type A T commands manua lly . However , there might be some occasions when you will need to do so . This chapter describes A T comman ds for da ta mode. Fax and voice commands are taken care of by application software. The format for entering A T command s is: AT X n w[...]

User ’s Manual C-2 A T Commands A/ Repeat last command This command repeats the last comm and strin g entered . Do not precede this command with an A T prefix or conclude it by pressing ENTER . AA n s w e r c o m m a n d This command instructs the modem to go off-hook and answer an incoming call. Bn Communication st andard setting This command de[...]

User ’s Manual C-3 A T Commands En Echo com m an d This command controls whether or no t the chara cters entered from your computer keyboard are disp layed on your monitor (echoed) wh ile the modem is in command mode. E0 Disables echo to the computer . E1 Enables echo to the computer (default). Result Codes: OK n=0,1 ERROR Otherwise Hn Hook cont [...]

User ’s Manual C-4 A T Commands M2 The speaker is always on when mod em is off-hook. M3 S peaker is on until the carrier is detected, excep t when dialing. Result Codes: OK n=0,1,2,3 ERROR Otherwise Nn Modulation handshak e This command controls whether or not the loca l modem performs a negotiated handshake at co nnection time with the remote mo[...]

User ’s Manual C-5 A T Commands Q1 Disables modem from sending result codes to the computer . Result Codes: OK n=0,1 ERROR Otherwise T Select tone dialin g This command instructs the modem to send DTMF ton es whil e dialing. Dialed digi t s are tone dial ed until a P command or dial mo difier is receiv ed. This is the defa ult setting. Vn DCE res[...]

User ’s Manual C-6 A T Commands Dial tone detect Disabled: The modem dia ls a call regardless of whether it detects a dial tone. Enabled: The modem dial s only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. Busy tone detect Disabled: The modem ign ores any busy to nes it receives. Enabl[...]

User ’s Manual C-7 A T Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: OK n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuratio n stored and programmed at the factory . This o peration r[...]

User ’s Manual C-8 A T Commands &Tn Self-test comma nds These tests can help to isolate problems i f you experience periodic data loss or random errors. &T0 Abort. S tops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection be tween the mode m and computer . Any data entered at the[...]

User ’s Manual C-9 A T Commands N3 V .42, MNP , or buffered (default). The modem attempts to connect in V .4 2 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V .42/MNP auto rel iable mode (same as &Q5 ). N4 V .42 or disconnect. T[...]

User ’s Manual D-1 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answer s and how long to wait before it hangs up if a connection fails. Y ou can also customize certain A T commands such as the e[...]

User ’s Manual D-2 S-registers S0 Auto answer ring n umb er This register determi nes the nu mber of ring s the modem will count before automatically answ ering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When di sable d, the modem can only answer with an A T A command. Range:0-255 Default:0 Units:rings S1 [...]

User ’s Manual D-3 S-registers S5 Command line editing characte r (user defined) This register sets the character recogniz ed as a backspace and pertains to asynchronous only . The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII. This char acter can be used to ed i t a com mand line. Whe n th[...]

User ’s Manual D-4 S-registers S8 Comma p ause time This register sets the time , in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set bo th wait before dialing and comma pause time. Range:0-255 Default:2 Units:seconds S1 1 DTM F dia ling speed This register determ[...]

User ’s Manual D-5 S-registers A T comm a nd set result codes The following table shows the result codes. The result code summar y S37 = 10 12000 bps S37 = 1 1 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps Result Code Numeric Descri[...]

User ’s Manual D-6 S-registers *1: EC on ly appears when the Extended Re sult Codes configuration option is enabled. EC is replaced by one of the followi ng symbols, depending upon the error control meth od used: V .42bis - V .42 error co ntrol and V . 42bis data compression. V .42 - V .42 error control only . MNP 5 - MNP class 4 error control an[...]

User ’s Manual E-1 Appendix E V. 9 0 The TOSHIBA internal modem uses V .90 technology . The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service prov ider that su pports V .90. As with a ny modem, the actual through put (speed of data transfer) de pends on analog telephone line con ditions, w[...]

User ’s Manual E-2 V. 9 0 T able E-1 Result codes for a V .90 connection No. Result code Description 70 CONNECT 32000 EC* Connection at 32000 bps 72 CONNECT 36000 EC* Connection at 36000 bps 74 CONNECT 40000 EC* Connection at 40000 bps 76 CONNECT 44000 EC* Connection at 44000 bps 78 CONNECT 48000 EC* Connection at 48000 bps 80 CONNECT 52000 EC* C[...]

User ’s Manual E-3 V. 9 0 * EC stands for the Error Control method, which appears onl y when the extended result codes conf iguration option is ena bled. EC is replaced by one of the following symbols, dep endi ng on the error control method used. A T Command V42bis V .42 error control and V .42bis data compression V42 V .42 error control only No[...]

User ’s Manual F-1 Appendix F Wireless LAN This appendix is intended to hel p you get your Wirel ess LAN netw ork up and running, with a mi nimum of parameters. Card S pecifications Form Factor PCI Express Mini Card Compati bility ■ IEEE 802.1 1 S tandard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi[...]

User ’s Manual F-2 Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purcha sed ■ T ype of pro duct Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been design ed for operation [...]

User ’s Manual F-3 Wireless LAN Supported Freque ncy Sub-bands Subject to the radio regulatio ns that apply in the countries/regions, your Wireless LAN card may sup port a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations th at apply in the countries/r[...]

User ’s Manual F-4 Wireless LAN ■ In a Wireless LAN Access Point, th e Wireless LAN card will use the factory-set default channel (p ri nted in bold), unless the LAN Administrator selecte d a different channel when co nfiguring the Wireless LAN Access Point device. Wireless IEEE 802.1 1 Channels Sets (Revision A and n Draft 2.0) Frequency Range[...]

User ’s Manual F-5 Wireless LAN *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in whi ch these channels can be used. When installing Wireless LAN cards, the channel configuration is ma naged as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, [...]

User ’s Manual G-1 Appendix G Intel ® Matrix S torage Manager If you are installing the operating syst em on a computer system which is configured for AHCI mode, you must pre-install the Intel ® Matrix Storage Manager driver using the F6 installation method de scribed in the Man ually Setting up Windows (Windows Vist a ® ) or Manually Setting [...]

User ’s Manual G-2 Intel ® Matrix S torage Manager Windows Setup Procedure 1. Connect the USB floppy diskette drive and in sert the above disk. 2. Insert the Windows Setup DVD into the optical disc drive and boo t the computer from the DVD. The Windows Setup program will start. 3. Carry out the setup process by follo wing the instructions disp l[...]

User ’s Manual G-3 Intel ® Matrix S torage Manager 3. When the message " Press F6 if you need to install a third party SCSI or RAID driver " appears on the screen, press the F6 key . 4. When the message " Setup will load support for the following mass storage device(s): " appears on the screen, press the S key . 5. Select &qu[...]

User ’s Manual H-1 Appendix H Bluetooth wireless technology Interoperability Bluetooth ™ Adapto r from TOSHIBA are designed to b e interoperable with any product with Bluetooth wireless te chnology that is based on F requency Hopping S pread S pectrum (FHSS) radio technology , a nd is compliant to: ■ Bluetooth S pecification V er . 2.0+EDR, a[...]

User ’s Manual H-2 Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technolog y , and TOSHIBA has not confirmed compatibility of its Bluetooth ™ products with all computers and/or equi pment using Bluetooth wirel ess technology other than TO SHIBA portable computers. Always use Bluetooth ™ A[...]

User ’s Manual H-3 Bluetooth wireless technology Interoperability Bluetooth w ireless techno logy and your Health The products with Bluetooth wireless te chnology , like other radio devices, emit radio frequency electromagnetic energy . The level of energy emitted by devices with Blu etooth wireless technology howeve r is far much less than the e[...]

User ’s Manual H-4 Bluetooth wireless technology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisa teur du dispositif doit étre prét à accepter tout brouillag e radioélectrique reçu, même si ce brouillage est susceptible de com[...]

User ’s Manual H-5 Bluetooth wireless technology Interoperability Caution: Exposure to Rad io Frequency Radiation The radiated output pow er of the Bluetoo th ™ Adaptor from TOSHIBA is far below the FCC radio frequen cy exposure limi ts. Nevertheless, the Bluetooth ™ Adaptor from T OSHIBA shall be used in such a manner that the potential for [...]

User ’s Manual H-6 Bluetooth wireless technology Interoperability Using Bluetooth ™ Adaptor from TOSHIBA equipment in Jap an In Japan, the frequency bandwidth of 2,400 - 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification syste m s (premises radio station an[...]

User ’s Manual H-7 Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Device Auth orization This device obtains the T echnical Conditions Compliance App r oval, and it belongs to the device class of radio equipment of low-power da ta communication system radio station st ipulated in the T elecommunications Business Law . The Name[...]

User ’s Manual I-1 Appendix I AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Certification agencies Length: Minimum 1.7 meters Wire siz[...]

User ’s Manual I-2 AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV - F . For the United S tates and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration mu st be 6- 15P (250V[...]

User ’s Manual J-1 Appendix J T OSHIB A Anti-thef t Protection T imer This feature al l ows yo u to set up a ti mer -activated BIOS p assword that will prevent unauthorised system a ccess in the event of theft. When the time limit is exceeded, you a re required to provi de the Password or fingerprint authentication for t he BIOS and Ha rd Disk Dr[...]

User ’s Manual K-1 Appendix K Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manu al, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) rel a te d to th is co mp ut er ar e marked with a blue *XX in thi s manual. Clicking [...]

User ’s Manual K-2 Legal Footnotes ■ use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high alti tude (all temperature references are approxi mate and may vary depending on the sp ecific computer model - plea s e re fe r to your com puter documen t ation or visit the T oshiba website at [...]

User ’s Manual K-3 Legal Footnotes Battery Life *4 Battery life may vary considerably depend ing on product model, configuration, applications, power ma nagement settings and features utilized, as well as the natural perf ormance variations produced by the design of indi vidual compone nts. Pu blished battery life numbers are achieved on select m[...]

User ’s Manual K-4 Legal Footnotes Wireless LAN *8 The transmission speed over th e wireless LAN and th e distance over which wireless LAN can re ach may vary depen ding on surro unding electromagnetic environment, obstacles, access po int design and configuration, and client design and software/hardware configurati ons. The actual transmission s[...]

User ’s Manual Glossa ry-1 Glossary The terms in this glossary cover topi cs related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating curre nt ANSI: American National S tandards Institute ASCII: American S tandard Code for Information Interchange BIOS: basic input output system bps: bits per second CD: com[...]

User ’s Manual Glossa ry-2 Glossary IDE: integr ated driv e electro nics IEEE: Institute of Electrical and Electronics Engineers I/O: input/ output IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte PC: personal computer PCI: peripheral co mponent inte rconnect RAM: [...]

User ’s Manual Glossa ry-3 Glossary ANSI: American National S tandards Instit ute. An organization established to adopt and define standards for a variety of technical discipl ines. For example, ANSI defined the ASCII standard and other information processing requirements. antist atic: A material used to prevent th e buildup of static electricity[...]

User ’s Manual Glossa ry-4 Glossary byte: The representation of a single cha racter . A sequence o f eight bits treated as a single unit; also the smallest addressa ble unit within the system. C cache memor y: High speed memory which stores da ta that increases processor speed and data transfer rate. When the CPU reads data from main memory , it [...]

User ’s Manual Glossa ry-5 Glossary comp at ibility: 1) The ability of one computer to accept and process data in the same manner as another com puter wi thout modifying the data or the media upon which it is b eing transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or par[...]

User ’s Manual Glossa ry-6 Glossary delete: T o remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication betwee n a specific peripheral device and the computer . dialog box: A window that accepts user input to make system settings or record other information. disk drive: The[...]

User ’s Manual Glossa ry-7 Glossary E echo: T o send ba ck a reflection of the transmitted data to the sending device. Y ou can display the information on the screen, or output it to the printer , or both. When a computer rece ives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer , th e print[...]

User ’s Manual Glossa ry-8 Glossary graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromech[...]

User ’s Manual Glossa ry-9 Glossary I/O devices: Equipment used to communicate with the compu ter and transfer data to and from it. J jumper: A small clip or wire that allows you to change the hardwa re characteristics by electrically connecting two points of a circuit. K K: T aken from the Greek word kilo, meaning 1000; often used as equivalent [...]

User ’s Manual Glossary-10 Glossary microprocessor: A hardware compon ent contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer . mode: A method of operation, for exa mple, the Boot Mode, Sl eep Mode or the Hibernation Mode. modem: Derived from [...]

User ’s Manual Glossary-1 1 Glossary P pa r it y: 1) The symmetrical relationship between two parameter values (integers) both of which are either o n or off; odd or even; 0 or 1. 2) In serial co mmun ica tions, an e rror detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or[...]

User ’s Manual Glossary-12 Glossary RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT . RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information th[...]

User ’s Manual Glossary-13 Glossary T ouch Pad: A pointing device inte grated into the TOSHIBA computer palm rest. TTL: T ransistor-tra nsistor logi c. A logic circuit design that uses switching transistors for gates and storage. U Universal Serial Bus: This serial interface le ts you communicate with several devices connected in a cha in to a si[...]

User ’s Manual Index-1 Index A AC adaptor 3-3 additional 3-45 connecting 1-4 ASCII characters 5-7 B Battery charging 6-7 extendin g l if e 6-10 indicator 2-13, 6-4 monitoring capacity 6-8 real time clock 3-3, 6-6 save mode 3-7 types 6-5 Battery pack 2-8, 3-2 additional 3-45 replacing 6-10 BIOS Setup 7-8 Bluetooth 3-5, 4-48 Bluetooth Stack for Win[...]

User ’s Manual Index-2 Index FN + F4 (Hibernate) 5-4 FN + F5 (Output) 5-4 FN + F6 (Brightness Down) 5-4 FN + F7 (Brightness Up) 5-4 FN + F8 (Wireless) 5-4 FN + F9 (Touch Pad) 5-4 FN + space (Zoom) 5-4 FN + Tab (ODD) 5-5 Function keys 5-2 G Graphics controller 3-4 H Hard disk drive 3-3 automatic power off 3-7 installing 3-34 removing 3-33 Hard Dis[...]

User ’s Manual Index-3 Index additional 3-45 installing 3-24, 3-29 problems 8-19 removing 3-28, 3-31 Memory Stick 3-19 problems 8-12 Modem 3-5, 4-43 connecting 4-45 disconnecting 4-46 jack 2-5 problems 8-22 properties menu 4-44 region selection 4-44 Moving the compu t er 4- 52 MultiMediaCard 3-19 problems 8-13 P Password power on 3-7 problems 8-7[...]

User ’s Manual Index-4 Index location 2-3 Sleep Mode 1-8 System automati c 3-7 Slice Expansion Battery 3-45, 6-5 Slice Expansion Battery adaptor 3-4 5 Smart Card 3-16 inserting 3-17 problems 8-11 removing 3-18 Soft keys enhanced keyboard 5-2 ENTER 5-3 ScrLock 5-3 Sound system headphone jack 2 -2 microphone 2-12 microphone jack 2-2 problems 8-20 S[...]