Toshiba PROT130 manual

Satellite T130,Satellite Pro T130, and PORT EGE T130 Maintenance Manual (960-Q08) Toshiba Personal Computer Satellite T130/Satellite ProT130/PORTEGE T130 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Copyright © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite T130, Satellite Pro T130, and PORTEGE T130 Series. The procedures described in this manual are intended to help service technicians isola[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite T130, Satellite Pro T130, PORTEGE T130 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For exa[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... .......1 1.2 System Block Diagram ..........................................................[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Chapter 2 Troubleshooting Procedures 2.1 Troubleshooting ........................................................................................................... .1 2.2 Troubleshooting Flowchart .....................................................................[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Procedure 1 Diagnostic Test Program Execution Check .............................26 Procedure 2 Connector Check and Replacement Check ..............................26 2.10 Wireless LAN Troubleshooting ..................................................................[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Chapter 3 Diagnostic Programs 3.1 Tests and Diagnostics Software Overview ................................................................... 2 3.2 Executing the Diagnostic Test ...................................................................................... 3 [...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) 3.21.5 How to enter data…………………………………………………………………68[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Chapter 4 Replacement Procedures 4.1 Overview ................................................................................................................... .... 1 Safety Precautions ...............................................................................[...]

Satellite T130, Satellite Pro T130, and PO RTEGE T130 Maintenance Manual (960-Q08) Appendices Appendix A Handling the LCD Module ................................................................................1 Appendix B Board Layout .....................................................................................................1 Appendix C P[...]

Satellite T130 and Satellite ProT130, PORTEG E T130Main tena nce Manu a l (960-Q08) Chapter 1 Hardware Overview[...]

Chapter1 Hardware Overview Satellite T130 and Satellite Pro T130, and PORTEGET130Mainten an ce Manual (960-Q08) 1 Hardware Overview Chapter 1 Contents 1.1 Features ................................................................................................................... ...... 1 1.2 System Block Diagram ....................................[...]

Chapter1 Hardware Overview Satellite T130 and Satellite Pro T130, and PORTEGET130Mainten an ce Manual (960-Q08) Figures Figure 1-1-1 Left of the computer.......................................................................................... 4 Figure 1-2-1 System Block Diagram ......................................................................[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) Features 1.1 Features The Satellite T130, Satellite Pro T130, PORT EGE T130 (Intel Platform) features are listed below.  Microprocessor Microprocessor that is used will be d ifferent by the model. It supports processors as follows - Inte[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) Keyboard module has 85 or 86 keys. It s upports Windows key and Application key.  Battery The RTC battery is equipped inside the computer. The main battery is a detachable lithium ion battery. -6 cell 10.8V -12cell 10.8V  USB (Univers[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) Some computers in this series of fer Bl uetooth wireless communication functiona lity. This module is Version 2.1+EDR.  Wireless WAN Some models are equipped with a Wireless W AN module.  Security Kensington Lock,  Hard Disk Drive [...]

Chapter 1 Hardware Overview 11 10 9 5 6 7 12 8 13 1 4 2 3 1. External Monitor port 12.Power Button 2. HDMI out port 13. Security Lock 3. USB port (USB Sleep and Charge function is supp orted by this port only.) 4. FAN HOLE 5. Keyboard 6. Touch Pad 7. Touch Pad Control Right Button 8. Touch Pad Control Light Button 9. Display Screen 10. Web Camera 1[...]

Chapter 1 Hardware Overview 7 1 8 2 3 4 5 6 1. LAN jack 8. DC-IN jack 2. USB port 3. USB port 4. Microphone jack 5. Headphone Jack 6 Bridge Media Slot 7. Wireless LAN/Wirele ss WAN Antennas Figure 1-1-2 right of the computer Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)[...]

Chapter 1 Hardware Overview 1.2 System Block Diagram Figure 1-2-1 shows the system block diagram. Figure 1-2-1 System block diagram for Intel Platform Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) The PC contains the following components.  CPU - Intel ○ R CoreTM 2 Duo : SU7300 - Intel ○ R CoreTM 2 Solo : SU3500 - Intel ○ R Pentium ○ R : SU4100, SU2700 Additional processors may be introduced.  Memory Two memory slots cap[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)  RTC  GPIO  Enhanced Power Management  SMBus 2.0  High Definition Audio Controller  569-pin 16mmx16mm mBGA Package  Other main system chips Clock Generator (CULV Plat form: ICS9LPRS365BKLFT) EC–[WO/CIR WPCE775CA0DG)] [...]

Chapter 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3-1 shows a view of the 2.5-inch HDD and Tables 1-3-2 and 1-3-3 list the specifications. Figure 1-3-1 2.5-inch HDD Standard value Parameter TOSHIBA MK2555GSX TOSHIBA MK3255GSX T[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) Standard value Parameter WD2500BEVT-26ZCT 0 WD3200BEVT-26ZCT0 Width (mm) 100 Height (mm) 12.5 Depth (mm) 70.0 Outline dimensi ons Weight (g) 101(Max) Specification Parameter TOSHIBA MK2555GS X TOSHIBA MK3255GSX TOSHIBA MK4055GSX TOSHIBA MK5[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) bus transfer rate (MB/s) 3Gbps Average random seek time (read) (m s) 12.0ms/13.0ms Power-on-to-r eady (sec) 3.5 (typ.) Specification Parameter WD2500BEVT-26ZCT 0 WD3200BEVT-26ZCT0 Storage size (format ted) 250GB 320GB Speed (RPM) 5,400 Data[...]

Chapter 1 Hardware Overview 1.4 Keyboard The Satellite T130, Satellite Pro T130, and PORTEGE T130 keyboard is for US style Figure 1-4-1 is a view of the keyboard for US style Figure 1-4-1 Keyboard for US style See Appendix E for details of the keyboard layout Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08)[...]

Chapter 1 Hardware Overview 1.5 TFT Color Display The Satellite T130, Satellite Pro T130, and PO RTEGE T130 use LED to control backlight. 1.5.1 LCD Module Figure 1-5-1 shows a view of the LCD module and Table 1-5- 2 lists the specifications. Figure 1-5-1 SAMSUNG LCD Module Specifications(WXGA+) LG LP133WH1 T LA1 AUO B133XW02 V0 Item Number of Dots [...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 1.6 Power Rails Table 1-6-1 lists the power rail output specifications. Power supply （ Yes/No ） Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Main Battery (w ith RTC Battery) +5VPCU 5 Yes Yes No +5V 5 No No No +3VPCU 3.[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 1.7 Batteries The PC has the following two batteries.  Main battery  Real time clock (RTC) battery Table 1-7-1 lists the specification s f or these two batteries. Battery Name Batte ry Element Output Voltage 6 Cell Li-ion 10.8v Main B[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) Power ON Power OFF 6 cell 5 ~ 10 hours about 5 hours 12 cell 5 ~ 10 hours about 4 hours Table 1-7-2 Time required fo r charges of main battery Charge is stopped in the following cases. 1. The main battery is fully charged 2. The main batter[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 1.7.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-7-4 lists the Time required for charge s of RTC battery and data preservation tim e. Condition Time Char[...]

Chapter 1 Hardware Overview Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual (960-Q08) 1.8 AC Adapter Table 1-8-1 lists the AC adapter specifications. Parameter Specification With Led DELTA/ LITE-ON 3pin DELTA/ LITE-ON 2pin Power 65W 65W Input voltage AC 100V/240V Input frequency 50Hz/60Hz Input current ≦ 1.5A Output voltag[...]

Satellite T130, Satellite Pro T130 and PORTEGE T130 Maintenance Manual ( 960-Q08) Chapter 2 Troubleshooting Procedures[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 , and PORT EGE T130 Maintenan ce Manual (960-Q08) Chapter 2 Contents Chapter 2 Contents 2.1 Troubleshooting ........................................................................................................... .1 2.2 Troubleshooting Flowchart .............................[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 , and PORT EGE T130 Maintenan ce Manual (960-Q08) Procedure 3 Connector and Cable Check.................................................... 24 Procedure 4 Replacement Check ................................................................ 25 2.9 LAN Troubleshooting .............[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Power supply 6. Display 11. HDMI 2. Sy[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-2-1 as a guide for determining which troubleshooting procedures to execute. Before going through th e flowchart steps, verify the following:  Ask cust[...]

Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (1/2) Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08) [...]

Chapter 2 Troubleshooting Procedures Figure 2-2-1 Troubleshooting flowchart (2/2) If the diagnostics program cannot detect an e rror, the problem may be intermittent. The Test program should be executed several tim es to is olate the problem. Check the Log Utilities function to confirm which diagnostic test de tected an error(s), and then perform t[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  4. If an error is found on th e touch pad test, perform the Touch pad Troubleshooting Procedures in Section 2.7. 5. If an error is detected on the display test, perfor m the Display Troubleshooting Procedures in S[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other P[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  *1 When the power supply controller detects a malfunc and perform the following procedure. tion, the DC IN icon blinks orange 2. Re- e dapter. If the icon bove, check the followings : Check 1 o to Procedure 2. Che[...]

Chapter 2 Troubleshooting Procedures Procedure 2 Connection Check The wiring diagram related to th e power supply is shown below: An o Ch o the PCN1 connector and wall outlet. If thes e cables are connected firmly, go to Check Check 2 Replace the AC adapter and th e AC power cord with new ones.  If the DC IN icon does not light, go to Procedure [...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Check 5 Replace the battery pack with a new one . If the battery pack is still not ch arged, go to Procedure 4.[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Procedure 4 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follo[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.4 System Board Troublesho oting is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed. The procedures Procedure 1: Message Check stic Test Program Execution Check [...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Procedure 1 Message Check When the power is turned on, the system perfor ms the Power on Self Test (POST) installed shown on the display, perform Check 1.  If t r rocedure 2.  If Free-DOS or W . Check 1 If o[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Procedure 2 Diagnostic Test Program Execution Check erform these tests. 1. System test 7. Ma 8. BIO 9. Sys 10. Wi 11. LA 12. UUID test-DMI Information (Write DMI) If an error is det ected during these tests, go to[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.5 SATA Hard Disk Drive Troubleshooting To check if HDD is malfunctioning or not, fo llow the troubleshooting procedures below as instructed. e 1: Partition Check 2: Message Check 3: Format Check Diagnostic Te st[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed n. Make sure no floppy disk is in the FDD. Turn on the computer and check the m essage on t[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  Procedure 3 Format Check The computer’s HDD is formatted using the Free-DOS FORMAT program or the physical format program of the test program. To fo rmat the HDD, start with Check 1 below and perform the other s[...]

Chapter 2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check bout r code is not displayed but the problem still occurs, go to Procedure 5. The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information a th[...]

Chapter 2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check tive. Otherwise, they may be faulty. Disassemble the com puter following instructions in Chapter 4, Replacement Procedures and perform the following ly c onnected to the connector(s) on the system board. HDD(s) is/are connected to the connector(s) on the system b[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.6 Keyboard Troubleshooting Procedure 1: Diagnostic Te st Program Execution Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test in th[...]

Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 stem board. Make sure keyboard cable is firmly co[...]

Chapter 2 Troubleshooting Procedures Satellite T130, Satellite Pro T130 and P ORTEGE T130Maintenance Manual (960-Q08)  2.7 Touch pad Troubleshooting ting Procedure 1: Diagnostic Te st Program Execution Check Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test in the Diagnostic Program. Refer to Chapter 3[...]

Chapter 2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 oard. Make sure the cable is fi rmly connected to[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) 2.8 Display Troubleshooting T p P Procedure 3: Connector and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the compute r’s external monitor port, and then boot the computer. The co[...]

Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD cable. Their cables may be disconnected from system board. Disassemble th e computer following the steps described in Chapter 4, Replacement Procedures . If the conn the problem still occurs, go . ection is loose, reconnect f[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) Procedure 4 Replacement Check LCD module, LCD cable are connected to displa y circuits. Any of these com ponen faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the fol ts ma[...]

Chapter 2 Troubleshooting Procedures 2.9 LAN Troubleshooting Procedure 1: Diagnostic Te st Program Execution Check Procedur Execute LA for more information on how to perform the test program. If any error The LAN f defective o aulty. To check if the computer’s LAN is malfunc tioning or not, follow the troubleshooting procedures below as instructe[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) 2.10 Wireless LAN Troubleshooting hooting Procedure 3: Replacement Check tion is enabled in BIOS setup ck the transmitting -receiving function of wireless LAN. You will need a s econd computer that can communicate by escribed in Chapter 3. If th[...]

Chapter 2 Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Make sure the wireless communication is En[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disa ssemble the computer and then perform the following checks: Check 1 [...]

Chapter 2 Troubleshooting Procedures 2.11 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting proce below as instructed. dures The conne Procedure 1: Connector Check Procedure 2: Replacement Check Procedure 1 Connector Check ction of sound system is shown in the following figure. As the connecti[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) Procedure 2 Replacement Check  If External microphone/Headphone does not work properly, perform check 1.  If internal microphone /Speaker do no t work properly, perform check 2.  If HP o heck 3.  If Volume control does not wo rk prop[...]

Chapter 2 Troubleshooting Procedures 2.12 Bluetooth Troubleshooting ooting ent Check h B lue tooth module is connected to system board. If B lue tooth malfunctions, its onnection is defective or B lue tooth cable and system board may be faulty. Check 1 To check if the computer’s B lue tooth is malfunctioning or not, follow the troublesh procedure[...]

Chapter 2 Troubleshooting Procedures 2.13 HDMI Troubleshooting To check if the computer’s HDMI is malf unctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External HDMI Monitor Check Check 1 Make sure HDMI cable is firmly conn ected to the connector CN11 (system board). If the problem still occur s, perform [...]

Chapter 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check HDMI monitor connected to HDMI&USB board by an HDMI cable. If the connection is loose, reconnect firmly and restart the co mputer. If the problem still occurs, go to Procedure 4. Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08)[...]

Chapter 2 Troubleshooting Procedures Satellite T130 and Satellite Pro T130 Main tenance Manual (960-Q08) Procedure 4 Replacement Check HDMI signals are connected to display circ uits via HDMI cable and HDMI&USB board. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for If characters or graphics on the internal[...]

Satellite T130, Satellite Pr o T130, and PORTEGE T130 Maintenan ce Man ual ( 960-Q08) Chapter 3 Diagnostic Programs[...]

Chapter 3 T est Program for Field _____________ ____________ ____________ ____________ ____________ _______________ _______ Satellite T130, Satellite Pr o T130 and PORTEGE T130 Maintenance Manua l ( 960-Q08) Chapter 3 Contents 3.1 Tests and Diagnostics Software Overview ............................................................... 2 3.2 Executing[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Chapter 3 Diagnostic Programs[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.1 Tests and Diagnostics Software Overview This chapter explains how to use the Tests and Diagnostics Software for the Satellite T 130, Satellite Pro T130 and PORTEGE T130 computer systems. NOTES : Before starting the Tests and Diagn[...]

Chapter 3 Test Program for Field 3.2 Executing the Diagnostic Test Free-DOS is required to run the Diagnostics Program. To start the programs follow these steps: 1. Create a Free-DOS bootable disk and copy all the files from the Tests and Diagnostics software to the disk. 2. Insert the boot disk into the computer’s floppy disk drive and turn on t[...]

Chapter 3 Test Program for Field The following menu displays: :Select item Enter:Decision item Esc:Escape TOSHIBA Satellite(Pro) P500 Diagnostics Version V1.00 [DIAGNOSTICS MENU] 01. DIAGNOSTIC TEST 02. RUNNING TEST 03. DMI INFORMATION 04. LOG UTILITIES 05. SYSTEM CONFIGURATION ::Select item ESC :Escape 06. OPTION 99. EXIT [DIAGNOSTIC TEST MENU] 01[...]

Chapter 3 Test Program for Field 4. Select the subtest you want to execute and press Enter . The following menu displays: Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 5. Select the desired test from the subtest menu and press Enter . The following Test Parameter menu displays: [ DIAGNOSTICS MENU ] 01. DIAG STIC[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) NOTES : The Item2 and 3 of Test Parameter are not used by some tests. Go To Test Move the highlight bar to Go to Test and press Enter to start executing the test. Test Loop Select NO to return the screen to the subtest menu after the [...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.3 Subtest names Table 3-3-1 lists the subtest names for each test program in the Diagnostic Test m enu. No. Test Name No. Subtest Name 01 SYSTEM TEST 01 02 03 04 FAN ON/OFF check Battery TEST CPU Temperature 3D HDD Protection Test ([...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) No. Test Name No. Subtest Name 05 FLOPPY DISK TEST 01 02 03 04 05 Sequential Read Sequential W/R/C Random Address/Data Write Specified Address Read Specified Address 06 HARD DISK TEST 01 02 03 04 05 06 07 08 Sequential Read Address Un[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) No. Test Name No. Subtest Name 10 MULTIMEDIA TEST 01 02 03 04 Sequential Read Test Random Read Test Read Specified Address Test 1 point W/R/C Test 11 MEMORY2 01 02 03 04 All one/zero Test Walking 1/Walking 0 Test(Left) Walking 1/Walki[...]

Chapter 3 Test Program for Field 3.4 System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains three subtests. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 FAN ON/OFF Checking Select 1,2,3 to control FAN on/o[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 03 CPU Temperature This will display CPU Temperature for check; press [ESC] to exit. [CPU_TEMP.EXE] Program Version: 1.3 03-09-2009 CPU Temperature: XX GPU Temperature: XX NOTES : If no external Graphics, GPU not report temper[...]

Chapter 3 Test Program for Field The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC 3 Test1 Judgment If all data is less than ranges, it will be OK. X Z Upper Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual[...]

Chapter 3 Test Program for Field The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 4 Test2 Judgment If all data is less than ranges, it will be OK. U pp e r Rear Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08)[...]

Chapter 3 Test Program for Field The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 5 Test3 Judgment If all data is less than ranges, it will be OK. U pp e r Right[...]

Chapter 3 Test Program for Field The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 6 Test4 Judgment If all data is less than ranges, it will be OK. U pp e r Front[...]

Chapter 3 Test Program for Field The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 7 Test5 Judgment If all data is less than ranges, it will be OK. 8 Inspection Judgment If all data is less than ranges, it will be OK. 9 Setting Calibration data W hen an inspection result is O.K., cali[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.5 Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s mem ory. Move the highlight bar[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,...8000H, 8004H, through FFECH Subtest 02 Prote[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) with the original data patterns. Addresses are displayed in 64KB increments during the test. Test Process: 1. Byte Enable Test One bit write/ 8 bit read” is executed and the new data is compared with the original data. Test data = C[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Test Process: 1. Checks the memory size to determ ine the maximum size of installed memor y. 2. Tests memory addresses 0 to the m aximum installed. 3. Writes, reads, and compares test data after a m emory refresh cycle (16ms or more).[...]

Chapter 3 Test Program for Field 3.6 Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains five subtests that test the computer’s keyboard and mouse actions. Move the highlight bar to the subtest you want to execute and press Enter . NOTE[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 04 Hot Key Display [9 Key] This subtest is used for the 9 hot key and functions the same as Subtest 1. ECO MUTE MUSIC PLAY BACK NEXT VOL- VOL+ WLAN Subtest 05 Hot Key Display [1 Key] This subtest is used for the 1 hot key and [...]

Chapter 3 Test Program for Field LEFT PRESS RIGHT PRESS TOUCH_PAD TEST Please Do Not Press the Left and Right Button At The Same Time Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08)[...]

Chapter 3 Test Program for Field 3.7 Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01[...]

Chapter 3 Test Program for Field Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25). The screen below displays when this subtest is executed. CHA[...]

Chapter 3 Test Program for Field Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H - 7EH using Mode 03H (80*25). The data displayed is shifted 1 byte to the left for each line as shown below. 80*25 CHARACTER DISPLAY 012345678901234567890123456789012345678901234567890123456789012345678901234[...]

Chapter 3 Test Program for Field Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white. The screen below shows the displays when this subtest is executed. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 320 * 200 GRAP[...]

Chapter 3 Test Program for Field 320*200 GRAPHICS DISPLAY : [D] BLACK D GRAY BLUE L BLUE GREEN L GREEN CYAN L CYAN RED L RED MAGENTA L MAGENTA BROWN YELLOW WHITE I WHITE Press [Enter] KEY Press ENTER to display 64 gradations of red, green, blue and white on the screen 320*200 GRAPHICS DISPLAY : [13] Satellite T130, Satellite Pro T130, and PORTEGE T[...]

Chapter 3 Test Program for Field Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolutions to display three windows; each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ([...]

Chapter 3 Test Program for Field Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolutions to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is execut[...]

Chapter 3 Test Program for Field 640*480 GRAPHICS DISPLAY : [12 ] BLACK DARK GRAY BLUE LIGHT BLUE GREEN LIGHT GREEN CYAN LIGHT CYAN RED LIGHT RED MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Me[...]

Chapter 3 Test Program for Field Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 0............................................................0 0............................................................0 0.................................[...]

Chapter 3 Test Program for Field Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHH[...]

Chapter 3 Test Program for Field Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break[...]

Chapter 3 Test Program for Field Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed. 640*480 COLOR ATTRIBUTE DISPLAY [...]

Chapter 3 Test Program for Field NOTE: The following screen does not display correctly. It will be amended in the next version. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [E[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Press [Enter] Key To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES were selected for Test Loop on the Test Parameter Menu.[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display. Black Red Green Blue Gray Red Gradation Green Gradation Blue Gradation White Red Gradation G[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.8 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Flopp[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 04 Write Specified Address NOTE : The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicate the head, and the last two digits indicate the sector. This subtest allows you to verify [...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.9 Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive. [...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, and then reads the data while moving from cylinder to cylinder. Data Pattern B5ADADH 4A525[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD. The following message displays on the screen to enter the test data. TEST DATA ????(=37b3H) Subtest 08 W -R-C Specified Address This subtest w[...]

Chapter 3 Test Program for Field 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions. Move the highlight bar to the subtest you want to execute and pr[...]

Chapter 3 Test Program for Field Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14 th address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION : When this subtest is executed, the current date and time are reset. This subtest checks the clock?[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cach e Memory Test contains eight subtests that test the computer's cache m[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes ), reads the new data and compares the result wi[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The High Resolution Display Test contains six subtests that te[...]

Chapter 3 Test Program for Field Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolutions to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) [ 640*480 256 ] Pres[...]

Chapter 3 Test Program for Field Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) [ 800*600 256 ] Pr[...]

Chapter 3 Test Program for Field Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolutions to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) [ 1024*768 256 ] [...]

Chapter 3 Test Program for Field Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH[...]

Chapter 3 Test Program for Field Subtest 06 Focus Test (“E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame. To exit this subtest and return to the High Resolution Display Test menu: Press Enter if NO was selected for Test Loop on t[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.13 Multimedia Test To execute the Multimedia Test select 10 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Multimedia Test contains four subtests that test the computer's m ultimedia fun[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and Follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's. Move the highlight ba[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) Tee test method is the same as Subtest2. However, the data to be used differs. 7FFF7FFF7FFF7FFF8000800080008000 BFFFBFFFBFFFBFFF4000400040004000 DFFFDFFFDFFFDFFF2000200020002000 FFFBFFFBFFFBFFFB0004000400040004 FFFDFFFDFFFDFFFD0002000[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests. Device Name Error Code Error Status Name (Common) FF Data Compare Error Memory 02 Protected Mode Not Ch[...]

Chapter 3 Test Program for Field Table 3-15-1 Error codes and error status names (2/2) Device Name Error Code Error Status Name HDD BB Undefined Error CC Write Fault E0 Status Error F0 No Sense Error ?? Other Error Cache Memory 02 Protect Mode Error 03 Caching Error ?? Other Error Multimedia 01 Write Error 0F Invalid Drive 15 Drive Not Ready ?? Oth[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.16 Running Test NOTES : 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated duri[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 3.17 DMI INFOEMATION Select 03 from the Diagnostics Menu and press Enter to Check or W rite DMI Information Data: 3.17.1 Check DMI Information The Check DMI Configuration program contains the following configuration information for th[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) c. AC Adapter Select [1]65W [2]75W [3]95W [4]120W Select 1 ~ c to key in new data , select 0 to exit program , program will com pare input data length with the max length , if over will retry key in Note: Please Check New DMI Informat[...]

Chapter 3 Test Program for Field 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log: 500 tim es). This function can store data on a floppy disk. If the power switch is turned off, the erro r inform ation will be lost. Error information is displayed in the fo[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostics M[...]

Chapter 3 Test Program for Field 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * - BIOS VER = VX.XX KBC VER = XXXX * - MAC ADDRESS : XXXXXXXXXXXX * - 0 ASYNC ADAPTER * - 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.:XXXXXXXX CUR LBA:XXXXXXXX OR[...]

Chapter 3 Test Program for Field 3.20 Running Test Edit Item 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test. KEY OPERATION  Cursor Down  Cursor Up PgDn Page Down PgUp Page Up Home[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08) 1. Enter a number or 0 for Loop Count and press Enter . Select a number from 1 to 65535 to define the num ber of times the Running Test executes. Select 0 to run the test continuously until halted by the user. 2. Select the NO or YES [...]

Chapter 3 Test Program for Field 3.21 Common Tests and Operation 3.21.1 How to operate a window To input parameters, or open a window use the following keys. key : to move a highlight bar [Enter] key : to select an item at the highlight bar [Esc] key : to close the current window and go back to the previous window 3.21.2 How to Stop the Test Progra[...]

Chapter 3 Test Program for Field Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test. Read Data Displays test data that has failed to com[...]

Chapter 3 Test Program for Field Satellite T130, Satellite Pro T130, and PORTEGE T130 Maintenance Manual ( 960-Q08)[...]

Satellite T130, Satellite Pro T130 ,an d PORT EGE T130Maintenance Manual (960-Q0 8) Chapter 4 Replacement Procedures[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) Chapter 4 Contents 4.1 Overview ................................................................................................................... .... 1 Safety Precautions ..........................................................[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) Figures Figure 4-2-1 Remove the battery pack................................................................................. 9 Figure 4-2-2 Install the battery pack ..................................................................[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) Figure 4-10-3 Remove the touchpad and touchpad board…………………………………41 Figure 4-11-1 Remove the I/O Board .................................................................................. 43 Figure 4-12-1 Rem[...]

Chapter 4 Replacement Procedures 4 2 4.1 Overview This chapter describes the procedure for rem oving and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the F RUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particular FRU can be removed. The[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1. In the case of the battery, always use authentic parts[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section ?[...]

Chapter 4 Replacement Procedures Disassembly Procedure Three main types of cable connector are used.  Pressure plate connector  Spring connector  Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cab le out from the connect or. W hen r[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the compute[...]

Chapter 4 Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage. NOTE : To tighten screws quickly and accu rately, an electric screwdriver is recom[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) Screw Notation To make maintenance of the co mputer easier, markings of the kinds of the screws including the types and lengths are i ndicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw [...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) 4.2 Battery pack Removing the battery pack The following describes the procedure for rem o ving the battery pack (See Figure 4-2-1). CAUTION: Take care not to short circuit the te rminals when removing the battery pack. Similarly, [...]

Chapter 4 Replacement Procedures LATCH 2 LATCH 1 Figure 4-2-1 Remove the battery pack NOTE : Dispose of the used battery pack in a ccordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for inst alling the battery pack (See Figure 4-2-2). CAUTION: There is a danger that the [...]

Chapter 4 Replacement Procedures 3. Attach the battery cover to the battery pack . 4. Insert the battery pack 5. Ensure the battery releas e latch (2) is moved into its locked position LATCH 2 Figure 4-2-2 Install the battery pack Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures 4.3 HDD Removing a HDD-H9.5mm The following describes the procedure for re moving the HDD (See Figure 4-3-1 to 4-3-3). CAUTION: Take care not to press on the top or bottom of a HDD. Press ure may cause data loss or damage to the device. 1. Turn the computer upside down. 2. Remove the following screws with a T6-bit T[...]

Chapter 4 Replacement Procedures Figure 4-3-1 Turn the computer upside down CAUTION: When a HDD is installed, they are inst alled in the position as the following figure. Figure 4-3-2 Remove HDD assembly Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder .  M3.0  3.0B FLAT BIND screw x4 M3*3 4pcs Figure 4-3-3 Remove HDD Installing HDD-H9.5mm The following describes the procedure for installing the main HDD. 1. Install a HDD to the HDD holder and secure it with the fo llo wing scre[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) 4.4 Memory Module CAUTION: The power of the computer must be turned off when you remove a memory module. Remove a memory module with the power on risks damaging the module or the computer itself. Do not touch memory module terminal[...]

Chapter 4 Replacement Procedures Figure 4-4-1 Remove memory slot cover Figure 4-4-2 Remove a memory module Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures Installing a memory module To install a memory module, confirm that the com puter is in boot mode. Then perform the following procedure (See Figure 4-4-3). 1. Insert a memory module into the connector of the com puter slantwise (term i nal side first) and press it to connect firmly. CAUTION: The power must be turned[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) 4.5 Keyboard Removing the keyboard The following describes the procedure for rem ovi ng the keyboard (See Fi gure 4-5-1 to 4-5-2). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do n[...]

Chapter 4 Replacement Procedures Figure 4-5-1 Remove 2 screws for KB Holder Figure 4-5-2 Remove 2 screws for Keyboard Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 ) Installing the keyboard The following describes the procedure for installing the keyboard. 1. Connect the keyboard flexible cable to the connector on the system board. 2. Slide and set the keyboard then secure it with the following[...]

Chapter 4 Replacement Procedures 4.6 Wireless LAN card and BT Module Removing a Wireless LAN card The following describes the procedure for re m oving a Wireless LAN card (See Figure 4-6-1 to 4-6-2). 1. Remove the screw of wireless LAN card.  M2x 2.5 BIND screw x2 2. Disconnect the wireless LAN antenna cable from the connectors on a wireless LAN[...]

Chapter 4 Replacement Procedures Figure 4-6-2 Remove a wireless LAN card Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures Installing a Wireless LAN card The following describes the procedure for installing a W ireless LAN card. 1. Insert a wireless LAN card terminals slantwise into the connector on the com puter and press a wireless LAN card and lock the secure screws. 2. Connect the wireless LAN antenna cable to the terminals on a wir[...]

Chapter 4 Replacement Procedures 4.7 3G module card Removing 3G module card The following describes the procedure for rem oving a 3G module card (See Figure 4-7-1 to 4-7-3). 1. Remove screw of 3G module board.  M2x 3.0 BIND screw x2 2. Disconnect the 3G module antenna cable from the connectors on a 3G module card 3. Remove a 3G module card from [...]

Chapter 4 Replacement Procedures Figure 4-7-2 Remove a 3G module card Satellite T130, Satellite Pro T130 , and PO RTEGE T1 30Maintenan ce Manual (960-Q08 )[...]

Chapter 4 Replacement Procedures Installing a 3G module card The following describes the procedure for installing a 3G m odule card. (See Figure 4- 7-3) 4. Insert a 3G module card terminals slantwise into the connector on the system board and press a 3G module card and lock the secure screws. 5. Connect the 3G module antenna cable to the terminals [...]

Chapter 4 Replacement Procedures 4 4.8 Display Assembly Removing the display assembly The following describes the procedure for rem o ving the display assembly (See Figure 4-8-1 to 4-8-5). 1. Close the display and turn the computer upside down. 2. Remove the battery pack (See Figure 4-2-1) 3. Open HDD Door Figure 4-8-1 Remove the screws (securing d[...]

Chapter 4 Replacement Procedures Figure 4-8-2 Remove the screws (from bottom side) 5. Disassemble KB Holder and KB screw (See Figure 4-5-1) 6. Remove the screws from the top side and remove the cover. Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-27[...]

Chapter 4 Replacement Procedures M2*5 7pcs Figure 4-8-3 Remove the screws (from top side) 7. Disconnect the FFC and cables. 8. Disassembly TOP ASSY 9. Pull out the wireless LAN antenna from the guide with two hands. Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-28[...]

Chapter 4 Replacement Procedures Figure 4-8-4 Remove the Wireless Antenna and LCD cable 10. Pull out the LCD cables from the guide of system board. Figure 4-8-5 Remove the LCD cable from system board Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-29[...]

Chapter 4 Replacement Procedures 11. Pull out the LCD cables from the guide of LCD panel. Figure 4-8-6 Remove the LCD cable from LCD panel Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-30[...]

Chapter 4 Replacement Procedures Opening the display to 135degree, keeping disp lay side by hand and remove the hinge screw. ‧ M2.5  4 FLAT BIND screw x4(Lock tight) ‧ M2.0  5 FLAT BIND screw x2(Lock tight) M2.5*4 4pcs M2*5 2pcs Figure 4-8-7 Remove the hinge screws 12. Re move the display assembly with two hands holding from the base asse[...]

Chapter 4 Replacement Procedures Installing the display assembly The following describes the procedure for installing the display assembly. 1. Inserting the pole of hin ge to the hole of hinge assembly, set the display assembly with hands on the base assembly. 2. Secure the hinges with the following screws secure the display mask with the following[...]

Chapter 4 Replacement Procedures 3. Connect the LCD harness to the connector on the system board. Figure 4-8-9 Connecting LCD harness to the system board 4. Arrange the wireless antenna cables along th e guide (front) and secure them with guide . 5. Pass the cables to the back of computer through the slot . 6. Arrange the Wireless LAN antenna along[...]

Chapter 4 Replacement Procedures Figure 4-8-10 Arrange and connect Wireless LAN cable 7. Install the LAN board and cover ASSY of the system. NOTE : If Fingerprint or Dust left on LCD screen during disassembly and assembly LCD units, please follow Appendix A to clean it. Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-[...]

Chapter 4 Replacement Procedures 4.9 Cover Assembly Removing the cover assembly The following describes the procedure for removing the cover assembly (See Figure 4-9-1 to 4-9-3). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer.  M2-0.4  2 FLAT BIND screw Back x6  M2[...]

Chapter 4 Replacement Procedures 3. Remove the following screws securing the cover assembly from the front of computer. Pull up and remove the cover assembly from the base assembly . M2.0  5.0 FLAT BIND screw Back x11 M2*5 7pcs Figure 4-9-2 Remove the screws (front) and cover assembly 4. Disconnect the touch pad flat cable/LAN cable/Power cable [...]

Chapter 4 Replacement Procedures Figure 4-9-3 Disconnect the touch pad flat cable/LAN cable Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-37[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-38 Installing the cover assembly The following describes the procedure for installing the cover assembly. 1. Install the cover assembly to the base assem bly. NOTE : Be careful not to catch the cables be tween cover assembly and b[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-39 4.10 Touch Pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-10-1 to 4- 10-3). 1. Peel off the glass tape and disconnect the touch pad flat cable, Fingerprint cable from t[...]

Chapter 4 Replacement Procedures Figure 4-10-1 Remove the touch FFC cable Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-40[...]

Chapter 4 Replacement Procedures M2-0.4*2 2pcs M2.0*3.0 2p cs M2*2-I 5pcs Figure 4-10-2 Loose the screws Figure 4-10-3 Remove the touchpad and touchpad board Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-41[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-42 Installing the touch pad The following describes the procedure for installing the touch pad. 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE : Do not reuse the touch pad so that it c an not be [...]

Chapter 4 Replacement Procedures 4.11 I/O Board The following describes for removing th e cover assembly (See Figure 4-11-1). Removing the I/O Board 1. Pull out the I/O Board FFC, LAN FFC, Speaker cable from I/O board connector. 2. Loose the below screws and then incline pull out I/O Board.  M2.0x3.0 FLAT BIND screw x2 Figure 4-11-1 Remove the I[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130Maintenan ce Manual (960-Q08 ) 4-44 Installing the I/O Board 1. Insert the I/O Board FFC, LAN FFC, Speaker cable into base case and connect I/O board cable and speaker cable 2. Fix the below screws then incline insert in I/O Board M2.0x3.0 FLAT BIND screw x2 NOTE[...]

Chapter 4 Replacement Procedures 4.12 System board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. if replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configu ration”. Removing the system board The following desc[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 46 Installing the system board The following describes the procedur e for installing the system board. 1. Secure the system board with the following screws . M2.0  3 screw x2 2. Connect the LAN FFC, LCD CABLE, ANTENNA, I/O board [...]

Chapter 4 Replacement Procedures Removing RTC battery The following describes the procedure for rem o ving the RTC battery unit (See Figure 4-12-2 to 4-12-3). 1. Pull the away the socket of RTC battery a nd use a clam p to hold RTC battery tightly. 2. Rotate battery through the way then remove it. Figure 4-12-2 Remove the RTC battery-step_1 Satelli[...]

Chapter 4 Replacement Procedures Figure 4-12-3 Remove the RTC battery-step_2 Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 48[...]

Chapter 4 Replacement Procedures Installing RTC battery The following describes the procedure for installing the RTC battery unit (See Figure 4-12-4). 1. Press the force vertically then lock the RTC battery tigh tly. Figure 4-12-4 Install the RTC battery Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 49[...]

Chapter 4 Replacement Procedures 4.13 CPU Removing the CPU heat sink The following describes the procedure for re m oving the CPU heat sink (See Figure 4-13-1). 1. Disconnect the Heat sink cable from the connector on the system board 2. Remove the following screws securing the heat sink holder along 1 to 3.  M2.0  3.0 screw x3 NOTE: When remo[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 51 Installing the CPU heat sink The following describes the procedure for installing the CPU heat sink 1. Secure the following screws securing the heat sink holder along 1 to 3.  M2.0  3.0 screw x3  Disconnect the Heat sink[...]

Chapter 4 Replacement Procedures 4.14 LCD unit Removing the LCD unit The following describes the procedure for re m oving the LCD unit (See Figure 4-14-1 to 4- 14-3). 1. Remove Screw MYLAR cover x4 2. Remove the following screws securing the display mask M2.0  5 screw x4 3. Insert your finger between the edge of the display mask and the LCD, and[...]

Chapter 4 Replacement Procedures Figure 4-14-2 Remove the LCD unit Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 53[...]

Chapter 4 Replacement Procedures 7. Remove the following screws securing the LCD support (LCD unit side) and rem ove the hinge from the LCD unit.  M2.0x2.5 screw x4 Figure 4-14-3 Remove the LCD hinge Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 54[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 55 Installing the LCD unit The following describes the procedure for installing the LCD unit. Install the LCD supports (LCD unit side) and hi nge to the LCD and secure them with the following screws .  M2.0  2.5 BINK screw x4 [...]

Chapter 4 Replacement Procedures 4.15 Web Camera module Removing Web Camera module The following describes the procedure for removing the Web Camera m odule. (See Figure 4-15-1 to 4-15-2). 1. Pull off the connect or of Web Cam era module. 2. Peel off the glue of Web Camera m odule. Figure 4-15-1 Remove the connector of Web Camera module Satellite T[...]

Chapter 4 Replacement Procedures Figure 4-15-2 Peel off the glue of Web Camera module Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 57[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 58 Installing Web Camera module The following describes the procedure for removing the Web Camera m odule. 1. Connect the connector of Web Camera module. 2. Pull in the glue of Web Camera Module.[...]

Chapter 4 Replacement Procedures 4.16 Application for Thermal grease on CPU and North Bridge (See Figure 4-16-1) I. For Flatiron thermal grease on North Bridge and CPU Figure 4-16-1 Intel &AMD Thermal grease on North Bridge and CPU A000018310 THERMAL GREASE FCR-AS A000062500 THERMAL GREASE 7762 Satellite T130, Satellite Pro T130 , and PORTEG E [...]

Chapter 4 Replacement Procedures II. Use grease on North Bridge and CPU 0.15cc for one repair. Figure 4-16-2 Apply silicon gr ease for North Bridge and CPU Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 60[...]

Chapter 4 Replacement Procedures 4.17 Speaker Box Removing Speaker Box The following describes the procedure for re moving Speaker Box. (See Figure 4-17-1 to 4- 17-3). 1. Remove the following screws securing Speaker Box.  M2.0  2.5 screw x 4 2. Removing the Speaker Box. Figure 4-17-1 Removing the secu ring screws at left side. Satellite T130,[...]

Chapter 4 Replacement Procedures Figure 4-17-2 Removing the secu ring screws at right side Figure 4-17-3 Removing the Speaker Box. Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 62[...]

Chapter 4 Replacement Procedures Satellite T130, Satellite Pro T130 , and PORTEG E T130 Maintenance Man ual (960-Q08) 63 Installing Speaker Box The following describes the procedure for removing Speaker Box. 1. Installing the Speaker Box. 2. Securing Speaker Box of following screws .  M2.0  2.5 screw x 4[...]

Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manual (960 -Q 08) Appendices[...]

Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manual (960 -Q 08) Appendix Contents Appendix A Handling the LCD Module ............................................................................. 1 Appendix B Board Layout ................................................................................................... 1 B.1 Sy[...]

Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manual (960 -Q 08) C.16 CN22 WLAN Connectors ............................................................................... 9 C.17 CN19 DDR Connectors………………...………………….………………10 C.18 CN20 DDR2 Connectors……………………………………?[...]

Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manual (960 -Q 08) Appendix F Wiring Diagrams .......................................................................................... F-1 F.1 RGB Monitor ID Wrapar ound Connector .................................................... F-1 F.2 LAN Loopbak Connector ...................[...]

Handling the LCD Module Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it is properly aligned and[...]

Handling the LCD Module 3. If the panel’s surface gets fingerprint or dus t, put on gloves and wipe it with static electricity cloth. If it is still d irty, drop some cleaning alcoho l on the surface and wipe it again. If the surface is much more fingerprint or dust, w e recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the[...]

Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite T130, Satellite Pro [...]

Handling the LCD Module Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manua l (960-Q08)[...]

Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause m alfunctions[...]

Handling the LCD Module 10. If you transport the module, do not use p acking material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). Thes e materials can release gas that can dam age the panel’s polarization. Satellite T130, Satellite Pro T130 , and PORTEGE T130 Maintenance Manua l (960-Q08)[...]

Board Layout Appendix B Appendix B Board Layout B.1 System Board 0 1 0 2 0 3 0 4 0 5 0 6 11 8 09 17 23 17 07 1 2 Figure B-1-1 System board layout (front) Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout 17 15 14 13 20 10 23 27 24 24 22 18 21 19 Figure B-1-2 System board layout (Back) NUM Location Function (01) CN 1 LVDS CONN (02) CN2 POWER BOARD CONN (03) CN3 KB CONN (04) CN4 LAN CONN Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08) (05) CN5 11” HDD CONN (06) CN6 TP CONN (07) CN7 ODD CONN (08) CN8 3G CONN (09) CN9 AUDIO&LAN&USB*2 CONN (10) CN10 RTC CONN (11) CN11 HDMI&USB*1 CONN (12) CN12 BT CONN (13) PCN1 AC-IN CONN (14) CN14 BATTERY CONN (15) CN15 FAN CONN (16) CN16 CT[...]

Board Layout B.2 Touch Pad Board <Front layout> SW02 SW01 Figure B-2-1 Touch Pad board layout (Front) NUM Location Function (01) SW1 Mouse Button Left key (02) SW2 Mouse Button Right key Table B-2-2 Touch Pad board connectors <Back layout> Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout 01 02 Figure B-2-3 Touch P ad board layout (Back) NUM Location Function (01) CN2 TP Board to TP Module CONN (02) CN3 TP Board to M/B CONN Table B-2-4 Touch Pad board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout B.3 CRT Board <Front layout> 01 Figure B-3-1 CRT Board layout (Front) Location Function (01) CN3 CRT CONN Table B-3-1 CRT Board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout B.4 HDMI Board <Front layout> 02 03 01 Figure B-4-1 HDMI Board layout (Front) Location Function (01) CN5 HDMI & USB PIN 37 CONN (02) CN1 HDMI CONN (03) CN4 USB CONN Table B-4-2 HDMI Board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout <Back layout> 02 01 03 Figure B-4-3 HDMI Board layout (Front) Location Function (01) U17 HDMI LEVEL SHIFT IC (02) CN1 HDMI CONN (03) CN4 USB CONN Table B-4-4 HDMI Board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout B.5 ADUIO & LAN & CARD READER & USB BOARD <Front layout> 07 02 03 05 06 04 01 Figure B-5-1 Audio&Lan&Usb&Card Reader Board layout (Front) Location Function (01) CN450 1 HDMI & USB PIN 37 CONN (02) CN1 USB CONN (03) CN4 USB CONN (04) CN9 Card read er CONN (05) CN8 External MIC CONN (06) CN6 Earphone CON[...]

Board Layout B.6 ADUIO & LAN & CARD READER & USB BOARD <Back layout> 01 04 05 08 07 06 Figure B-6-1 Audio&Lan&Usb&Card Reader Board layout (BACK) Location Function (01) CN1 USB CONN (02) CN4 USB CONN (03) U5 CARD READER IC (04) U5 CARD READER IC (05) U5 CARD READER IC (06) U5 CARD READER IC 02 03 Satellite T130, Satell[...]

Board Layout Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08) (07) CN8 External MIC CONN (08) CN6 Earphone CONN Table B-6-2 Audio&Lan&Usb&Card Reader Board IC[...]

Board Layout B.7 POWER BOARD <Front layout> 01 Figure B-7-1 Power Board layout (F ront) Location Function (01) CN1 POWER CONN Table B-7-2 Power Board connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout B.8 SIM CARD BOARD <Front layout> 01 Figure B-8-1 SIM Card Board layout (Front) Location Function (01) CN1 SIM CARD CONN Table B-8-2 SIM Card connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Board Layout B.9 SIM CARD BOARD <Back layout> 01 Figure B-9-1 SIM Card Board layout (Back) Location Function (01) JSIM1 SIM CARD MAOUBLE CONN Table B-9-2 SIM Card connectors Satellite T130, Satellite ProT130, and PORTEGE T130Maintenance Ma nual (960-Q08)[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) Appendix C Pin Assignment CN1 LCD Panel Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 VIN --- 2 VIN --- 3 LCDVCC --- 4 LCDVCC --- 5 +3V --- 6 CDD_POWE R I 7 MIC_GND --- 8 IN_MIC_R I 9 GND --- 10 GND --- 11 USBP3-_LCD --- 12 USBP3+_LCD[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 5 GND --- 6 CRT_DDCDAT I/O 7 CRT_VSYNC I 8 CRT_DDCCLK I/O 9 CRT_HSYNC I 10 GND --- 11 GND --- 12 CRT_RED I 13 CRT_GREEN I 14 GND --- 15 GND --- 16 CRT_BLUE I CN 2 LAN Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 AVDD_CEN --- 2 TX1P -[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) CN 6 Power Board Connectors PIN No. Signal name I/O PIN No. Sig na l name I/O 1 +5VPCU I 2 NBSWON# I 3 PWRLED# I 4 GND --- CN3 Keyboard Connectors PIN No. Signal name I/O PIN No. Sig na l name I/O 1 K_LED_P --- 2 MY16 O 3 --- --- 4 MX17 O 5 --- --- [...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 33 FN_F10 O 34 NUMLED O CN6 Touchpad Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 GND --- 3 GND --- 4 LID591# O 5 TPCLK I 6 TPDATA I 7 MMC)LED# --- 8 3G_WIMAX_LED# --- 9 RF_LED I 10 SATA_LED#_C --- 11 BAT_SAT1 I 12 BAT_SAT0[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 15 GND --- 16 USBP0+ I/O 17 USBP0- I/O 18 GND --- 19 USBP1+ I/O 20 USBP1- I/O 21 GND --- 22 USB_EN#0_1 I 23 +3V --- 24 +1.5V --- 25 +5V --- 26 +5V --- 27 +5V --- 28 +5VPCU --- 29 +5VPCU --- 30 +5VPCU --- 31 +5VPCU --- 32 +5VPCU --- 33 MMC_LED# --- 3[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 1 RTC_NO2 I 2 GND --- CN 18 SATA HDD Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 SATA_TXP0_R I/O 3 SATA_TXN0_R I/O 4 GND --- 5 SATA_RXN0_R I/O 6 SATA_RXN0_R I/O 7 GND --- 8 +3V --- 9 +3V --- 10 +3V --- 11 GND --- 12 GND --[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 11 NC --- 12 BUSBP9- I/O 13 BUSBP9+ I/O 14 GND --- 15 USBOC9# O 16 USB_SLEEP_EN# I 17 BOARD_ID4 O 18 PORT-B_HPD# --- 19 SDVO_CTRLDATA O 2 0 SDVO_CTRLCLK O 21 GND I 22 TMDSB_ CLK# I 23 TMDSB_CLK I 24 GND --- 25 TMDSB_DATA0# I 26 TMDSB_ DATA0 I 27 GND[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 9 MBAT+ --- 10 GND --- 11 GND --- CN21 3G Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 3G_WAKE# O 2 +3V --- 3 NC --- 4 GND --- 5 NC --- 6 +1.5V_3G --- 7 --- --- 8 UIM_PWR I/O 9 GND --- 10 UIM_DATA I/O 11 CLK_PCIE_3G# I 12 UIM_CLK I/O[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 41 +3V_3G --- 42 3G_LED# --- 43 NC --- 44 NC --- 45 NC --- 46 NC --- 47 NC --- 48 +1.5V_3G --- 49 NC --- 50 GND --- 51 NC O 52 +3V_3G --- CN22 WLAN Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 WLAN_WAKE# O 2 +3V --- 3 WCS_DATR --- 4 [...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 33 PCIE_TXP6 I 34 GND --- 35 GND --- 36 USBP10- I/O 37 GND --- 38 USBP10+ I/O 39 NC --- 40 GND --- 41 NC --- 42 WIMAX_LED# --- 43 GND --- 44 NC --- 45 CL_CLK1_WLAN --- 46 NC --- 47 PLTRST#_PCIE --- 48 +1.5V --- 49 CL_RST#1_WLAN --- 50 GND --- 51 NC [...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 25 GND --- 26 GND --- 27 M_B_DQS#1 I/O 28 M_B_DM1 I/O 29 M_B_DQS1 I/O 30 DDR3_DRAMRS T# I 31 GND --- 32 GND --- 33 M_B_DQ11 I/O 34 M_B_DQ14 I/O 35 M_B_DQ10 I/O 36 M_B_DQ15 I/O 37 GND --- 38 GND --- 39 M_B_DQ16 I/O 40 M_B_DQ20 I/O 41 M_B_DQ21 I/O 42 [...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 77 NC --- 78 NC --- 79 M_B_BS#2 I 80 M_B_A14 I 81 +1.5VSUS --- 82 +1.5VSUS --- 83 M_B_A12 I 84 M_B_A11 I 85 M_B_A9 I 86 M_B_A7 --- 87 +1.5VSUS --- 88 +1.5VSUS --- 89 M_B_A8 I/O 90 M_B_A6 I/O 91 M_B_A5 I/O 92 M_B_A4 I/O 93 +1.5VSUS --- 94 +1.5VSUS --[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 129 M_B_DQ32 I/O 130 M_B_DQ36 I 131 M_B_DQ37 I/O 132 M_B_DQ33 I/O 133 GND --- 134 GND --- 135 M_B_DQS#4 I/O 136 M_B_DM4 I/O 137 M_B_DQS4 I/O 138 GND --- 139 GND --- 140 M_B_DQ38 I/O 141 M_B_DQ34 I/O 142 M_B_DQ39 I/O 143 M_B_DQ35 I/O 144 GND --- 145 [...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 181 M_B_DQ56 I/O 182 M_B_D Q61 I/O 183 M_B_DQ57 I/O 184 GND --- 185 GND --- 186 M_B_DQS#7 I/O 187 M_B_DM7 I/O 188 M_B_DQS7 I/O 189 GND --- 190 GND --- 191 M_B_DQ60 I/O 192 M_B_DQ58 I/O 193 M_B_DQ62 I/O 194 M_B_DQ63 I/O 195 GND --- 196 GND --- 197 SA[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 23 M_A_DQ8 I/O 24 M_A_DQ13 I/O 25 GND --- 26 GND --- 27 M_A_DQS#1 I/O 28 M_A_DM1 I/O 29 M_A_DQS1 I/O 30 DDR3_DRAMRS T# I 31 GND --- 32 GND --- 33 M_A_DQ9 I/O 34 M_A_DQ14 I/O 35 M_A_DQ10 I/O 36 M_A_DQ11 I/O 37 GND --- 38 GND --- 39 M_A_DQ23 I/O 40 M_[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 75 +1.5VSUS --- 76 +1.5VSUS --- 77 NC --- 78 NC --- 79 M_A_BS#2 I 80 M_A_A14 I 81 +1.5VSUS --- 82 +1.5VSUS --- 83 M_A_A12 I 84 M_A_A11 I 85 M_A_A9 I 86 M_A_A7 --- 87 +1.5VSUS --- 88 +1.5VSUS --- 89 M_A_A8 I/O 90 M_A_A6 I/O 91 M_A_A5 I/O 92 M_A_A4 I/[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 127 GND --- 128 GND --- 129 M_A_DQ32 I/O 130 M_A_DQ34 I 131 M_A_DQ37 I/O 132 M_A_DQ39 I/O 133 GND --- 134 GND --- 135 M_A_DQS#4 I/O 136 M_A_DM4 I/O 137 M_A_DQS4 I/O 138 GND --- 139 GND --- 140 M_A_DQ33 I/O 141 M_A_DQ36 I/O 142 M_A_DQ38 I/O 143 M_A_D[...]

Pin Assignment Satellite T130, Satellite Pro T130 , and PO RTEGE T130 Main tenan ce Manual (960-Q08) 179 GND --- 180 M_A_DQ57 I/O 181 M_A_DQ63 I/O 182 M_A_D Q60 I/O 183 M_A_DQ56 I/O 184 GND --- 185 GND --- 186 M_A_DQS#7 I/O 187 M_A_DM7 I/O 188 M_A_DQS7 I/O 189 GND --- 190 GND --- 191 M_A_DQ59 I/O 192 M_A_DQ62 I/O 193 M_A_DQ61 I/O 194 M_A_DQ58 I/O 1[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Appendix. D Appendix D Display Codes D.1 Display Codes Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06 86 2E F0 2[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34 36 H 23 A3 33 F0 33 37 J 24 A4 3B [...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *1 76 Del E0 53 E0 D3 E0 71 E0 F0 71[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79  [...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79  E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 80 Ho[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 6[...]

Display Codes Satellite T130, Satellite Pro T130 , and PORT EGE T130Mainten ance Manual (960-Q0 8) Code set 1 Code set 2 Key top Shift Make Make Pause Co m mo n* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E Table D-1-7 No.126 key scan code *: This key generates only make codes.[...]

Keyboard Layout Appendix E Keyboard Layout 1. United Status (US) K eyboard Figure E-1-1 US keyboard 2. United Kingdom (UK) K eyboard Figure E-2-1 UK keyboard _____________ ____________ ____________ ____________ ____________ _______________ ____________ ____________ ____ Satellite T130, Satellite Pr o T130, and PORT EGE T1 30Maintenan ce Manua l (96[...]

Keyboard Layout 3. Japan K eyboard Figure E-3-1 Japan keyboard _____________ ____________ ____________ ____________ ____________ _______________ ____________ ____________ ____ Satellite T130, Satellite Pr o T130, and PORT EGE T1 30Maintenan ce Manua l (960 -Q08)[...]

Wiring Diagrams Satellite T130, Satellite Pro T13 ,a nd PORTEG E T130Maintenance Ma nual (960-Q0 8) Appendix F Appendix F Wiring Diagrams F.1 RGB Monitor ID Wraparound connector Figure F-1-1 RGB Monitor ID Wraparound connector (15PIN to 15PIN) F.2 LAN Loopback Connector (1) BIBAP ‘ (TX + ) ( 2 ) BIDA N (TX-) (3) BIDBP (RX+) (4) BIDBN (RX-) Figure[...]