ADTRAN 25 manuel d'utilisation

AT&T AT&T System 25 Installation and Maintenance Manual 555-540-103 B November 1995[...]

©1989 AT&T All Rights Reserved Printed in USA TO ORDER COPIES OF THIS DOCUMENT REFER TO DOCUMENT NUMBER 555-540-103 Contact: Your AT&T sales representative, or Call: 800-432-6600, Monday through Friday between 7:30 am and 6:00 pm EST, or In Canada call: 800-255-1242 Write: AT&T Customer Information 2855 North Franklin Road P.O. Box 199[...]

DANGER Do not open the fan assembly or remove rear cabinet cover before unplugging the cabinet from the electrical outlet. Wait at least five minutes after unplugging the power cord before removing the rear cover or power supply. The AT&T System 25 cabinets are not user serviceable. Some voltages inside the cabinets are hazardous. This equipmen[...]

THE FOLLOWING SYMBOLS AND PICTOGRAPHS APPEAR ON THE EQUIPMENT SYMBOL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions ELECTRICAL SHOCK Warns of the danger of electrical shoc k from hazardous voltages present within the control unit Warn[...]

FCC NOTIFICATION AND REPAIR INFORMATION AT&T SYSTEM 25 This telephone equipment is registered with the Federal Communications Commission (FCC) in accordance with Part 68 of its Rules. In compliance with the Rules, be advised of the following: MEANS OF CONNECTION Connection of this telephone equipment to the nationwide telecommunications network[...]

that certification in writing may be required when an existing multifunction system is being reconfigured as a Key system, if the customer desires the lower rate. — For Digital connections with D4 Framing Format provide the Facility interface code 041DU9-B, for digital connections with Extended Framing Format, provide the Facility interface code [...]

Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. HEARING AID COMPATIBILITY The voice terminals described in this manual are com[...]

FCC WARNING STATEMENT Federal Communicatlons Commission (FCC) Rules require that you be notified of the following: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply wit[...]

normally dialed from a telephone associated with the system. Such an off- premises network call is originated at, and will be billed from, the system location. The Remote Access feature, as designed, helps the customer, through proper administration, to minimize the ability of unauthorized persons to gain access to the network. Most commonly, phone[...]

● When possible, block out-of-hours calling. ● Frequently monitor system call detail reports for quicker detection of any unauthorized or abnormal calling patterns. ● Limit Remote Call Forward to persons on a “need-to-know” basis.[...]

Contents INTRODUCTION FCC PRECAUTIONS INSTALLATION TOOLS AND TEST EQUIPMENT CROSS-CONNECT EQUIPMENT DESCRIPTION Trunk Access Equipment 700A-110-BI -25 or 700A-66-B1-25 Cut-Down Jack 108 Emergency Transfer Unit (ETU) Station Interconnect Panel (SIP) 617A Panel Adapters Fanning Strip Cables Splitter Cables Octopus Cables 853B Adapter Cable DS1 Connec[...]

TDM Bus Connections. Ground Wire Connections. POWER UP AND INITIALIZE SYSTEM Connect Power Connect Administration Equipment Cold Start the System Check Performance of Cabinet Components Report Problems Initialize System INSTALL CROSS-CONNECT EQUIPMENT Install TAE, 617A Panels, and Fanning Strips Mount 858A orZ210A2 Adapters INSTALL MODULAR BULK POW[...]

Make SIP Connections for Data Terminals and Computers Make SIP Connections to Cabinet for ATL Cordless Telephones Perform SIP Housekeeping INSTALL EMERGENCY TRANSFER UNITS (ETUs) Make Emergency Transfer Connections Install Ground-Start Key INSTALL ATTENDANT CONSOLE INSTALL TERMINALS Label Terminals Stand-Alone Voice Terminals Stand-Alone Remotely P[...]

7300H Series Voice Terminals INSTALL MUSIC-ON-HOLD INTERFACE FCC-Registered Music Source Interface Non-FCC Registered Music Source Interface INSTALL EXTERNAL ALERTS INSTALL RECORDED DELAY ANNOUNCEMENT 2-115 2-117 2-117 2-119 2-120 2-121 2-121 2-121 2-122 2-124 2-128 INSTALL DICTATlON SYSTEM INTERFACE INSTALL PAGING SYSTEM INTERFACE Direct Connectio[...]

MAKE POOLED MODEM TEST CALL . . . . TEST TRANSFER TO DATA . . . . ... . . . TEST EXTERNAL ALERT (NIGHT SERVICE) TEST TEST TEST TEST TEST 3-11 3-11 3-12 DICTATION SYSTEM ACCESS 3-13 PAGING INTERFACE MUSIC-ON HOLD EMERGENCY TRANSFER TOUCH-TONE RECEIVERS 3-13 3-14 3-15 3-16 MAINTENANCE 4-1 EQUIPMENT NEEDED Precautions GENERAL INFORMATION System Errors[...]

ROUTINE MAINTENANCE Reseating and Replacing Circuit Packs Removing and Restoring Power Restarting the System ERROR LOG Accessing the Error Log From the SAT ERROR MESSAGES Clearing System-Detected Troubles Complete System Failure Common Control Trouble Circuit Pack Trouble Frontplane Ribbon Connector Trouble (Release 1 Only) Power Supply Trouble Pow[...]

REFERENCES ABBREVIATIONS AND ACRONYMS 5-1 6-1 A-1 APPENDIX A: System Wiring Connector Pin Assignments System 25 Building Wiring APPENDIX B: Parts Listing Tables A-1 A-1 B-1 APPENDIX C: System Additions or Changes Evaluate Cabinet Unit Power Load Add Circuit Pack Add Cabling Set Option Switches on TN760B CP Replace Circuit Pack Add Cabinet Add Termi[...]

APPENDIX F: Administration Error Messages GLOSSARY INDEX F- 1 G-1 I- 1 -viii-[...]

Figures Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-6a. Figure 2-7. Figure 2-8. Figure 2-9. Figure 2-10. Figure 2-11. Figure 2-12. Figure 2-13. Figure 2-14. Figure 2-15. Figure 2-16. Figure 2-17. Figure 2-18. Figure 2-19. Figure 2-20. Figure 2-21. Figure 2-22. Figure 2-23. Figure 2-24. Figure 2-25. Figure 2-26. [...]

Figure 2-37. Figure 2-38. Figure 2-39. Figure 2-40. Figure 2-41. Figure 2-42. Figure 2-43. Figure 2-44. Figure 2-45. Figure 2-46. Figure 2-47. Figure 2-48. Figure 2-49. Figure 2-50. Figure 2-51. Figure 2-52. Figure 2-53. Figure 2-53a. Figure 2-54. Figure 2-55. Figure 2-55a. Figure 2-56. Figure 2-57. Figure 2-58. Figure 2-59. Figure 4-1. Figure 4-2.[...]

Figure 4-8. Figure 4-9. Figure 4-10. Figure 4-11. Figure 4-11.a. Figure 4-12. Figure 4-13. Figure C-1. Figure C-2. Figure C-3. Table 2-A. Table 2-B. Table 2-C. Table 2-D. Table 2-E. Table 2-F. Table 4-A. Table 4-B. Table 4-C. Table 4-D. Table 4-E. Table 4-F. Table A-A. Table A-B. Table A-A. Table A-B. Table C-A. Table C-B. Table E-A. Table E-B. AC [...]

Table E-C. Table E-D. Table E-E. Table E-F. Table E-G. . . Table E-H. Table E-1. Table E-J. Table E-K. Table E-L. Table E-M. Table E-N. Table E-0. Table E-P. Table E-Q. Table E-R. Table E-S. Table E-T. Table E-U. Table E-V. Table E-W. Table E-X. Table E-Y. Table E-Z. Table E-AA. Table E-AB. Table E-AC. Table E-AD. Table E-AE. Table E-AF. Table E-AG[...]

INTRODUCTION INTRODUCTION This manual provides procedures and information for installing, and testing the AT&T System 25 Release 3 and associated equipment. The maintenance information contained in Section 4 pertains to the AT&T System 25 Release 1, Versions 1 and 2 (RI VI and R1V2), Release 2, Version 1 (R2V1 ), as well as to AT&T Syst[...]

INTRODUCTION ● ● ● ● ● ● ● ● Section 5 References-Lists and describes other related documentatio n Section 6 Abbreviations and Acronyms-Lists and describes abbreviations and acronyms frequently encountered in System 25 documentation Appendix A. System Wiring Table–Lists pinouts and wiring used with System 25 Appendix B. Parts List[...]

INSTALLATION INSTALLATION Installation of a System 25 requires the completion of a number of basic steps, similar to those required to install any customer switching system. Assuming that the building (station) wiring is already in place, the recommended sequence of steps for installation of the system is as follows: 1. Preinstallation Requirements[...]

INSTALLATION TOOLS AND TEST EQUIPMENT Table 2-A lists tools and test equipment required for installing a System 25. Table 2-A. Tools and Test Equipment Required for Installation Task s Tools Required Recommended Type Install Push Drill Cross-Connect Screwdriver 8-inch Flat Blade Field Carpenter’s Level 30-inch Rul e 30-inch Chalk Line 11 O-type P[...]

INSTALLATION CROSS-CONNECT EQUIPMENT DESCRIPTION This section provides a brief description of some of connect/interconnect equipment. More details on the can be found in the Reference Manual (555-540-200). the following: ● Trunk Access Equipment 700A Jacks Emergency Transfer Unit ● Station Interconnect Panel — 617A Panel Adapters Fanning Stri[...]

INSTALLATION Trunk Access Equipment The trunk access equipment (TAE) consists of 700A-I 10-61-25 or 700A-66- B1 -25 (157BF) cut-down jacks, or equivalent, and up to four 10B Emergency Transfer Units (ETUs). The 10B ETU is shown in Figure 2-1. 700A- 110-M-25 or 700A-66-B1-25 (157BF) Cut-Down Jack Trunk circuits that appear on the network interfaces [...]

INSTALLATION NOTE: 9“ WIDE, MOUNTING CENTERS ARE 8-1/2” APART, FLANGES OVERLAPPED Figure 2-1. 10B ETU 2-5[...]

INSTALLATION Station Interconnect Panel (SIP) The SIP is the station cross-connect field and consists of the following equipment: ● 617A Panels ● Adapter s ● 50A Fanning Strips. 617A Panel The 617A Panel is a metal plate with keyslot holes on each side for mounting on a backboard. (See Figure 2-2.) Each 617A Panel can hold eight 2210A2 or 858[...]

INSTALLATION MOUNTING CENTERS WHEN FLANGES ARE OVERLAPPED Figure 2-2. 617A Panel 2-7[...]

INSTALLATION Adapters The adapters shown in Figure 2-3 are used at the SIP. Z210A2 or 858A Adapters These adapters connect the building wiring (station runs) to the station port circuit packs (CPs) located in the system cabinets (through octopus cables). As many as 40 of these adapters may be required for a maximum size system, Any combination of t[...]

INSTALLATION Z21OA1 ADAPTER Y-ADAPTER WP90851,L1 858A ADAPTER Figure 2-3. SIP Adapters 2-9[...]

INSTALLATION Fanning Strip The 50A Fanning Strip (Figure 2-4) is a metal panel with positions to hold 16 octopus (switch) cables. The bundled portion of the octopus cable is anchored at the fanning strip. The eight octopus cable cords hang free. One fanning strip is required for 1-cabinet systems. Two fanning strips are required for 2- or 3-cabinet[...]

INSTALLATION Cables Splitter Cables The splitter cables (Figure 2-5) connect trunk circuits from the 700A jacks to the system cabinets or 10B ETU (3:1 only). 3:1 Splitter Cable (WP90929, L1) This cable connects the twenty-four 1-pair trunk circuits on a 700A jack to three 8-port trunk circuit packs (loop start, ground start, or DID). The connection[...]

INSTALLATION Octopus Cables Octopus cables (Figure 2-6) connect the station port and CPU/Memory circuit packs to the SIP adapters. Each cable consists of a 25-pair male connector that connects to the switch cabinet and eight modular plugs that connect to the SIP adapters. These cables are provided with all system cabinets. Figure 2-6. Octopus Cable[...]

INSTALLATION connector and a KS23146,L3 50-pin male connector. To connect a DS1 interface circuit pack to a 551-type Unit (CSU), field terminate the 15-pin plug. To connect DS1 tie trunks on co-located System 25s, 50-pin male connector (see Figure 2-1 9). Customer Service field terminate the ● C6E connector cable (comcode 104307 434)—1 00-foot [...]

INSTALLATION AT&T CAR 1 CABLE LABELS CAB1 SLOT1 CAB1 SLOT1 CAB1 SLOT2 CAB1 SLOT2 CABl SLOT3 CAB1 SLOT3 CAB1 SLOT4 CAB1 SLOT4 CAB1 SLOT5 CAB1 SLOT5 CAB1 SLOT6 CAB1 SLOT6 CAB1 SLOT7 CAB1 SLOT7 CAB1 SLOT8 CAB1 SLOT8 CABl SLOT9 CAB1 SLOT9 CAB1 SLOT10 CAB1 SLOT10 CAB1 SLOT11 CAB1 SLOT11 CAB1 SLOT12 CAB1 SLOT12 CAB1 SLOT CAB1 SLOT CAB1 SLOT CAB1 SLOT[...]

INSTALLATION Symbols Used in Figures Modular jacks are shown by the triangle symbol. The 25-pair connectors are indicated by shaded blocks. Generally, only one leg of an octopus cable is shown. Unterminated wiring requiring cut down or other termination does not show symbolic designations. The 103A Connecting Block is a typical modular wall jack th[...]

INSTALLATION PREINSTALLATION REQUIREMENTS The AT&T System 25 Reference Manual (555-540-200) provides a complete listing of System 25 equipment location requirements. Before installation begins, check the items described in this section. Caution: System 25 cross connect hardware must be located in a restricted access area only. Table and Backboa[...]

NOTES : 1. 2. 3. 4. 5. 115V AC, 60 Hz, 15 AMP OUTLETS (HUBBELL 5262 OR EQUIVALENT) MUST BE LOCATED WITHIN 4 FEET OF SYSTEM CABINETS. MULTIPLE CABINET SYSTEMS REQUIRE TWO QUAD OUTLETS, SINGLE CABINET SYSTEMS REQUIRE ONE QUAD OUTLET. ALLOW AT LEAST 24 INCHES OF SPACE IN FRONT OF CABINETS. TABLE MUST BE ABLE TO SUPPORT 250 POUNDS. BACKBOARD IS 3/4 INC[...]

INSTALLATION AC Power All cabinets and any locally-connected System 25 peripheral equipment (System Administration Terminal [SAT], Station Message Detail Recording [SMDR] device, Digital Tape Unit [DTU]), and Customer Service Unit (CSU) used for DS1 connections must be plugged into the common ac power outlet. This outlet must have an associated gro[...]

INSTALLATION 3. 4. metal frame of the building, a concrete encased ground, or a ground ring. If these grounds are not available, the water pipe ground can be supplemented by one of the following types of grounds. ● Metal underground gas piping system—an electrically continuous metal underground gas piping system that is uninterrupted with insul[...]

INSTALLATION ● A single-point ground (SPG) system in which the green wire ground (system ground) and the telephone company ground are connected to approved building ground. ● The coupled bonding conductor must be connected between the telephone company ground at the building entrance and System 25’s SPG. ● Surge protection on the ac power t[...]

INSTALLATION Secondary Protection External secondary protection, located at the trunk access area of the System 25 cross-connect field, is required for all trunks and off-premises lines. Refer to Table 2-B for approved trunk protectors. FROM AC LOAD CENTER (TWO SEPARATELY FUSED 15 AMP CIRCUITS ) SINGLE POINT GROUND H GROUND I LOAD CENTER II (GREEN)[...]

INSTALLATION Building Wiring Building (station) wiring (must be 24 AWG or heavier) from voice and data terminals to the equipment location should already be in place. System 25 wiring requires that 4-pair circuits be distributed from the equipment location to each station’s wall jack. The SIP hardware (Figures 2-2 through 2-6), designed specifica[...]

INSTALLATION INSTALL SYSTEM CABINETS Before beginning the cabinet installation, position the cabinet table within 2 feet of the ac power receptacle. Make sure that the cabinets are easily accessible from both the front and the back. Position Cabinet(s) Caution: A fully-equipped cabinet weighs 80 pounds . 1. 2. 3. 4. Check Unscrew and remove the upp[...]

INSTALLATION Table 2-B. Circuit Packs, Their Functions, and Protectors Approved Secondary Circuit Pack Function Wiring Protector N/A ZTN78 Supports single-line voice terminals. (Must not be used on out-of-building circuits, ) SCP-1 or 79A TN742 Supports off-premises, out-of- building, and bridged single-line voice terminals. lTW/LlNX343* I ROB ZTN7[...]

INSTALLATION Two fans are located on the left-hand front side of each cabinet. The cabinet’s power supply is located behind the fans; to the right of the power supply are up to 12 CPs in individual slots. Each CP is identified by a label on the front. See Figure 2-10. 1. Remove the front cover of each cabinet. 2. Note any obviously bent or otherw[...]

INSTALLATION Figure 2-10. Three-Cabinet System, Front View With Covers Removed 2-26[...]

INSTALLATION Figure 2-11. Position of Shorting Plugs on CPU/Memory Circuit Pack 2-27[...]

INSTALLATION Required Circuit Pack Positions The required CP positions for Cabinet 1 are: SLOT CP 1 ZTN129 or ZTN130 (R3) I 2 I ZTN85 or ZTN131 (R3) Also, all DID Trunk circuit packs should be installed in Cabinet 1. There are no other restrictions on CP position in a single-cabinet or multicabinet system; however, you should refer to the power sup[...]

INSTALLATION Install 4A Retainer Clips The 4A retainer clips must be installed on each of the 12 receptacles on the lower rear panel of the cabinets. To install a clip, position it and insert the legs in the cabinet as shown in Figure 2-12. Figure 2-12. 4A Retainer Clip Installation 2-29[...]

INSTALLATION Connect Cabinets The Time Division Multiplex (TDM) bus extender cable and the intercabinet #6 AWG ground wire must be connected between cabinets. The TDM bus terminates on each side of the cabinet, and the intercabinet #6 AWG ground wire connects to the ground block at the rear of each cabinet. Note: Make certain that the address plug [...]

INSTALLATION side up). 3. Install the upper rear panels. Route the extender cable between the slots formed by the upper and lower rear panels. 2-31[...]

INSTALLATION TDM BUS TER M CARD ADDR PLUG TDM B EXTEN CABLE ADD PL U PLU G Figure ~CABINET 3 ON/OF F .SWITC H AC POWE R # 6 AWG BUILDING GROUND WIR E CABINET 2 AC POWER . #6 AW G 2-13. TDM Bus Terminations (Rear View of 3-Cabinet System) 2-32[...]

INSTALLATION Ground Wire Connections The cabinets are connected to the single-point ground with #6 AWG copper wires. (Building ground requirements are described in Preinstallation Requirements in this section.) Warning: The cabinet power switches must be set to off. 1. In 2- or 3-cabinet systems, connect a #6 AWG wire between the ground blocks of C[...]

INSTALLATION 5. Starting with Cabinet 2 or 3, turn on the power switch on each cabinet [Cabinet 1 must be last). IMPORTANT: If power to Cabinet 1 is not turned cold start initialization may not occur properly. 6. Check to be sure that the cabinet fans are rotating. Connect Administration Equipment on last, the Connect the SAT and DTU to their respe[...]

INSTALLATION Cold Start the System To ensure that the system recognizes the current position of the CPs, you must cold start the system before beginning initialization. A cold start causes the system to check all slots for valid CP types and assign default translations to ail ports (except auxiliary trunk ports). A limited cold start is available. [...]

INSTALLATION 7. The system will respond with: Action= 8. Enter 20 for a cold start. The system will respond with: Save/Restore: Action=20 Data= 9. Enter D. The system will complete the word Data followed by the = sign. 10. Enter 1 for a cold start or 2 for a limited cold start. The system will respond with: Save/Restore: Action=20 Data=1 (or You ar[...]

INSTALLATION Cold and warm starts both display the same type of information on the SAT. This consists of a listing of the version of the firmware loaded in the CPU/Memory CP, followed by a configuration listing of all CPs recognized by the system. The CPU/Memory CP is not in the configuration listing; however, it is located in slot 1 of Cabinet 1. [...]

INSTALLATION The SAT message for a cold or warm start appears after the system has performed all self-tests and reading of its configuration. Typical cold start SAT message is as follows. The example is for a 2-cabinet system. Typical Release 3 Version 3 Cold Start Message RESTART TS ROM pair 1:version 3.5 * FC ROM pair 1:version 3.13 ● FC ROM pa[...]

INSTALLATION Check Performance of Cabinet Components Each CP has three colored LEDs on the front panel that indicate whether it is functioning properly or not. When a cold start is performed, the system undergoes a series of self-tests and loads default translations. Upon initial power application, each CP tests itself. The red LED on the CP lights[...]

INSTALLATION Table 2-D. Circuit Pack LED Status Indications Circuit Pack Type LEDs if Normal LEDs if Failed Service Circuit (ZTN85 Steady Green and Steady Red or or ZTN131 [R3]) Flashing or Amber Off Steady Amber CPU/Memory (ZTN129 Flashing Green Steady Green or ZTN130 [R3]) or Off All Other Steady Green Steady Red (Amber Also lighted (see Note bel[...]

INSTALLATION If all the CPs are operating properly, only the green LED on the CPU/Memory CP and the amber LED on the Service Circuit should be flashing. If any other CP has a no-lighted LED, the CP may need to be reseated. All port CPs green LED remains dark until at least one port on the CP has been translated. Except for the CPU/Memory CP and Ser[...]

INSTALLATION Figure 2-15. Typical System 25 Port Circuit Pack Report Problems Follow local procedures to report faulty or damaged equipment. 2-42 November 1995[...]

INSTALLATION Initialize System Instructions for initializing the system (based on the completed implementation forms) are provided in the Administration Manual (555-540-500). Note: Before trunks using DS1 Signaling are administered, all link level parameters such as signaling and framing and all link level alarms must be cleared. If this is not pos[...]

INSTALLATION Install TAE, 617A Panels, and Fanning Strips To install this equipment, proceed as follows: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. For each RJ21X, RJ2GX, and RJ48X 700A Jack 1/2-inch from the edge of switch cabinet(s). Mount the first 617A Panel. network interface, install one the backboard closest to the Position and mount the first 50A F[...]

INSTALLATION FIRS T 108 ET U PLYWOO D BACKBOARD 1/2 " ADD'L 700A BLOCK ADD'L ET U ADD'L 700A BLOCK ADD'L 700A BLOC K ADD' L 617 A PANEL ADD'L 617 A PANEL ADD'L 617 A PANEL ADD'L 617 A PANEL ADD'L 700A BLOC K ADD'L ET U 700A BLOC K ADD' L ET U 700 A BLOCK TO SWITCH CABINET D-RINGS AS REQ&ap[...]

INSTALLATION NOTE: GREATER THAN 48" FO R 5-PANE L ARRANGEMEN T FIRS T 10 8 ET U Figure 2-17. Alternate SIP and TAE Backboard Layout 2-46[...]

INSTALLATION Mount 858A or 2210A2 Adapters To install these adapters, proceed as follows: 1. Using a wide blade screwdriver, pry off the upper adapter mounting clip on the 617A Panel (Figure 2-18). 2 . Fit the mounting clip on the top of the adapter. 3. Fit the adapter in the slot of the lower mounting clip. 4. Press the upper mounting clip back in[...]

INSTALLATION UPPER ADAPTER MOUNTING CLIP Figure 2-18. Mounting Adapters[...]

INSTALLATION INSTALL MODULAR BULK POWER SUPPLY (Optimal) The 346 Modular Bulk Power Supply (MBPS) is a cost-effective and flexible alternative to the KS-2291 1 power supply. The 346 MBPS can be used where the wall-mounted (outlet) KS-2291 1 power supply cannot be used or where multiple KS-2291 1 power supplies are required. The 346 MBPS consists of[...]

INSTALLATION Tie trunks must be segregated on a separate block because a different splitter cable is used. Also, off-premises stations must be segregated one 700A Jack. The first five trunks in each group of eight (loop start or ground start trunks only) can be connected through an ETU to five power failure transfer stations. However, all eight tru[...]

INSTALLATION Connect Cabinets to TAE Blocks The connections between the cabinets and the TAE blocks are made using connectorized splitter cables. Make sure that each trunk group on each connecting block is connected to the correct type of CP and protected with its approved secondary protector (as shown in Table 2-B). Central office trunks associate[...]

INSTALLATION Connect Tie Trunks A 2:1 connectorized splitter cable, WP90929, L3, is required to connect the 700A Jack to the cabinet for tie trunks. 1. 2. 3. 4. 5. 6. Install secondary protectors (see Table 2-B). Using the cable label sheets provided (Figure 2-7), label the back of the hood of each of the connectors (1 and 2) on the two legs of the[...]

INSTALLATION Install DS1 DS1 signaling allows a digital connection between the System 25 and other PBXs, Central Offices, Toll Offices, off premise stations, and data end points such as host computers. The TN767 emulates ground start, Ioopstart, tie and DID Trunks in addition to off premises stations. The ZTN131 circuit pack provides the required d[...]

INSTALLATION Figure 2-19. Direct Connection (Side by Side) NOTE: FOR DISTANCES OVER 50 FEET (15.2 M) USE C6E CONNECTOR CABLE(S) BETWEEN H600 307,G2 CONNECTOR CABLE AND DS1 TRUNK CIRCUIT PACK. Figure 2-20. Direction Connection (Side by Side) Connections Between 1311 and 4310 Feet For distances between 1311 and 4310 feet, CSUs equipped with Office re[...]

Figure 2-21. DS1 Connections—1311 to 4310 Feet DS1 Connections—4311 Feet or More For distances of more than 4311 feet, T1 line repeaters are required in addition to the CSUs. See the “Install CSU” section of this manual for installing the CSU. Figure 2-22 shows a functional diagram of this connection. If the connection is being made between[...]

INSTALLATION Off Premises Metallic (Cable) Connections The connection between the System 25 and another DS1 interface is in most cases a T1 line with repeaters. The proper lightning protection must be provided (as shown in Table 2-B). Figure 2-23 shows a diagram of the off premise cabling. See the “install CSU” section of this manual for the in[...]

INSTALLATION MICROWAVE INTERFACE MICROWAVE INTERFACE LIGHT-GUIDE INTERFAC E LIGHT-GUIDE INTERFAC E INFRARED INTERFACE INFRARE D INTERFACE 655 FEET MAXIMU M ANY DS 1 INTERFACE 655 FEET MAXIMUM ANY DS 1 INTERFACE Install *DSX-1 REFERS Figure 2-24. DS1 Customer Service TO A PHYSICAL CROSS-CONNECT FOR DS1 SIGNALS Connections—Non Metallic Connections [...]

INSTALLATION Connect the CSU The CSU can be powered by the line or from a locally provided -48 V dc power supply. Figure 2-25 shows the connections for connecting the CSU. The 48 V and GRD leads are optional according to how the CSU is powered. H600 307 ,0 2 CONNECTO R CABLE (NOTE) NOTE : FOR DISTANCES OVER 50 FEET ( 15.2 M) USE C6E CONNECTOR CABLE[...]

INSTALLATION Consideration should be given to installing secondary protection on each out-of-building facility connected to the TAE if any of the following conditions exist : ● The service entrance (protector block) ground is not properly installed (bonded to building ground, for example). ● The local telephone company does not permit access to[...]

INSTALLATION INSTALL EQUIPMENT ROOM STATION CABLING System 25 is connected to the building (station) wiring in two stages. First, the building wiring is connected to the Station Interconnect Panel (SIP). Then, the octopus cables from the back of the cabinets are connected to the SIP. Accurate documentation during installation is essential to the pe[...]

INSTALLATION . 2-61[...]

INSTALLATION Connect Building Wiring to SIP The type of building wiring termination determines what types of adapters are used. Two types are supported: 4-pair cable (cut down) and modular jack. Any combination of adapters may be mounted on a 617A Panel. Cluster the connection on the SIP by voice terminal type: single-line, 7300H Series*, Multibutt[...]

INSTALLATION Z21OA1 ADAPTER (MODULAR TO MODULAR) PURSE LOCK CLIP / ( TYPICAL) Figure 2-27. Modular Plug Terminations Connected to the SIP 2-63[...]

INSTALLATION 4-Pair Cable Terminations Each 4-pair cable supports one station (Figure 2-28). It connects to a wiring block on a 858A Adapter. 1. 2. 3. 4. 5. 6. Run the 4-pair cable through the rings at the top of the 617A Panels. Cut down the leads starting with Pin 1 of the wiring block located beside the modular jack (Figure 2-28). Wiring Block D[...]

INSTALLATION ZZ1OA1 ADAPTER (MODULAR TO MODULAR) PURSE LOCK CLIP (TYPICAL) Figure 2-28. Cut Down Terminations Connected to the SIP 2-65[...]

INSTALLATION Connect Cabinets to SIP Table 2-E shows the type of terminals that can be connected to each CP type and the maximum allowable cabling distances to the system cabinets. Refer to the Voice and Data Station Records Form for the terminal types assigned to each workstation. Caution : Connecting a terminal to the wrong type of CP can damage [...]

NSTALLATION Prepare Carrier Loading Labels As you connect the port CPs in each cabinet to the SIP, list the connections on the Carrier Loading label. This label is mounted on the inside of the front cover of the cabinet. (See Figure 2-29.) Keep track of –48 volt power usage so that the power supply is not overloaded. 1. 2. 3. 4. Enter, the CP typ[...]

INSTALLATION 2-68[...]

INSTALLATION Modify Octopus Cables if Required If flag--type cable ties are shipped loose, they must be installed on the early production octopus cables. The flag-type cable tie location depends on the type of SIP arrangement (Figures 2-16 and 2-17). Also, if the alternate SIP arrangement is used, later production octopus cables must be modified. 1[...]

INSTALLATION TO SWITCH TO SWITCH DISTRIBUTION RIN G FLATTEN OCTOPUS CABLE BEFORE FEEDING INTO TH E 50A FANNING STRIP ION THE FLAG MOD PLUG ENDS TO FAN OUT TO (D-RINGS) AS REQ’ D ADAPTERS ON SI P TIE WRAP IN FRON T OF THE WIRE FORM SI P FLAG TIE WRA P WITH OCTOPUS CABL E IDENTIFICATION LABE L Figure 2-30. Standard and Modified Octopus Cables 2-70[...]

INSTALLATION Make SIP Connection for CPU/Memory In all cases, the CPU/Memory is connected to the SIP via an octopus cable. Since there are four ports on the CPU/Memory (port 1 for the SAT, port 2 for SMDR, port 3 for the DTU, and port 4 [reserved]), plugs 1 through 3 on the octopus cable are used to connect the peripheral equipment. (Plugs 7 and 8 [...]

INSTALLATION FLAG-TYPE CABLE TIES STANDARD CABLE I MODIFIED CABLE FOR (FLAG TIE ALTERNATE SIP ARRANGEMENT AT 65” REMOVED) Figure 2-31. Mounting Octopus Cable on Fanning Strip 2-72[...]

INSTALLATION Make SIP Connections to Cabinet for 7300H Series Terminals 1. 2. 3. 4. 5. 6. 7. 8. 9. Select the cable label sheet (Figure 2-7) that identifies the cabinet (blue for #1, orange for #2, and green for #3). On an octopus cable, attach an appropriate label (CAB1 SLOT8, for example) on the last flag-type cable tie and on the back of the hoo[...]

INSTALLATION Make SIP Connections to Cabinet for MET Sets Follow the same procedure as for 7300H Series terminals to connect MET set SIP appearances to the appropriate CPs as outlined below: ● ● ● ● ● Note: Connect the 25-pair connector to a TN735 CP Attach a cable label to the octopus cable 25-pair connector and flag- type tie wrap Run t[...]

INSTALLATION ● Attach cable labels to the two octopus cable 25-pair connectors and flag-type tie wrap. ● Attach octopus cables to the 853B adapter ● Run the cables to the 50A Fanning Strip. ● Plug the cable ends into the appropriate adapters, and complete the Voice and Data Station Records Form. November 1995 2-74a[...]

INSTALLATION Make SIP Connections for Data Terminals and Computers Any RS-232C compatible data terminal, personal computer host computer, or a STAR LAN NETWORK workstation can be connected in one of four ways: ● If the terminal has a modem, it should be connected to a ZTN78 CP in the same way as a single-line voice terminal. ● The terminal’s [...]

INSTALLATION 4. Complete the Voice and Data Station Records Form (Figure 2-26). Make SIP Connections to Cabinet for ATL Cordless Telephones Follow the same procedure as for 7300H Series terminals to connect ATL Cordless Telephone SIP appearances to the appropriate CPs as outlined below: ● Connect the 25-pair connector to a ZTN79 CP ● Attach a c[...]

INSTALLATION 6. Check that all cables are labeled. INSTALL EMERGENCY TRANSFER UNITS (ETUs) The 106 Emergency Transfer Unit (ETU) (Figure 2-32) supports up to five Power Failure Transfer (PFT) sets and a DID make-busy function. Up to four ETUs can be supported for a maximum of 20 PFT sets. The sets can be connected to selected loop-start or ground s[...]

INSTALLATION Figure 2-32. 10B Emergency Transfer Unit 2-78[...]

INSTALLATION Figure 2-33. Emergency Transfer Unit Connections 2-79[...]

INSTALLATION Make Emergency Transfer Connections Note: The following procedure assumes that the network interfaces 1. 2. 3. 4. 5. 6. 7. are connected to the 700A jacks and connector 0 of the 3:1 splitter cables has been connected to the jack. See Install Equipment Room Trunk Cabling in this part. Connect Trunk Lines From Cabinet to ETU Using the ca[...]

INSTALLATION 8. 9. 10. 11. 12. 13. Connect a 25-pair plug on octopus cable to the SIP receptacle on the ETU. Mount the octopus cable on the 50A Fanning Strip (Figure 2-31). Connect all eight legs of the octopus cable to adapters (port side) at the SIP. The first five stations (legs 1 through 5) are the Power Failure Transfer stations. Document the [...]

INSTALLATION Install Ground-Start Key If trunks are ground start (ZTN76 used), a ground-start key must be installed on the Power Failure Transfer voice terminals. This key can only be installed on voice terminals that have modular jacks. 1. Unplug modular line cord from voice terminal. 2.Plug KS23566, L1 key into voice terminal line cord jack. 3. P[...]

INSTALLATION INSTALL ATTENDANT CONSOLE Most systems will have one or two attendant consoles. Release 2 Version 1 and Release 3 systems support direct trunk attendant consoles (DTAC) or switched loop attendant consoles (SLAC). The system can support either one or two of the DTAC or SLAC consoles but not a combination of DTACs and SLACs. The installa[...]

INSTALLATION Figure 2-35. Attendant Console With DXS Console 2-84[...]

INSTALLATION 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. lf a DXS is supplied, place it beside the attendant console. For locally powered DXS, do Steps 5 through 8. For remotely powered DXS, do Steps 9 through 13. Locally Powered DXS Plug the 400B2 Adapter into the wall jack. Plug one end of the D6AP-87 Cord into the 6-conductor modular jack of the 400B2 Ada[...]

INSTALLATION LEGEND : ZTN79 - B1 - cl - C2 - C7 - P2 - S1 - W1 - HYBRID LINE CP TYPICAL - 103A CONNECTING MODULAR CORD (D8W-87) OCTOPUS CABLE (WP90780) MODULAR CORD (D6AP-87) NODULAR BULK POWER SUPPLY POWER UNIT (346A) POWER PANEL (346A-1) BLOCK 23A1 SELECTOR CONSOLE-USED IN CONJUNCTION WITH EITHER SLAC OR DTAC INSIDE WIRING CABLE Figure 2-36. Remo[...]

INSTALLATION INSTALL TERMINALS When installing terminals at workstations, consult the Voice and Data Station Records Form to make sure that you are connecting the right terminal type at each workstation. In a replacement installation, single-line and MET voice terminals already in place may not need to be replaced, although the MET labels change. I[...]

INSTALLATION Label Terminals Be sure to label the feature buttons of 7300H Series voice terminals replace labels on MET sets per Table 2-F. Table 2-F. Feature Button Abbreviations and Labels Feature Name Administration Button Button Code Label [ ]* Account Code Entry 15 ACCT ENTRY Agent Status for CMS 42 MONITOR [PDC]* Agent Status for CMS 42 AVAIL[...]

INSTALLATION Table 2-F. Feature Button Abbreviations and Labels (Contd.) * [ ] Indicates that a meaningful value for this item should be substituted. † These features cannot be changed or reassigned. Att.-Attendant Console November 1995 2-89[...]

INSTALLATION Stand-Alone Voice Terminals See Figure 2-37. 1. Unpack each terminal and examine it for damage. On Model 420 voice terminals, set the TONE/PULSE switch to TONE. 2. At the workstation, connect one end of the terminal line cord to the terminal and the other end to the modular wall jack. LEGEND: B1 C1 C2 C 9 MET SETS MET SETS W 1 248B ADA[...]

INSTALLATION Stand-Alone Remotely Powered Voice Terminals See Figure 2-38. 1. Unpack each terminal and examine it for damage. 2. At the workstation, connect one end of the terminal line cord to the terminal and the other end to the modular wall jack. LEGEND : ZTN79 - B1 - cl - C2 - C7 - P2 - P1 - W1 - HYBRID LINE CP TYPICAL - 103A CONNECTING BLOCK [...]

INSTALLATION Single-Line and 7300H Series Voice Terminals With Associated ADUs See Figures 2-39 and 2-40. 1. 2. 3. 4. 5. 6. Unpack each voice terminal and ADU and examine them for damage. Arrange 7300H Series terminals and single-line terminals with appropriate ADUs (see Note). Note: The Z3A1 ADU is equipped with a male RS-232C connector, and the Z[...]

INSTALLATION B1 - TYPICAL - 103A CONNECTING BLOCK Cl - MODULAR CORD (D8W-8T) C2 - OCTOPUS CABLE (WP90780) C5 - MODULAR CORD (D4BU-87) - FURNISHED WITH SET “ WI - INSIDE WIRING CABLE WP90851-L1 - MODULAR Y ADAPTER Z3A1 ADU - EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA CORD NOTES : 1. IF RANGE IS GREATER THAN 2000 FT FROM SYSTEM CABINET, TERMINAL DATA RA[...]

LEGEND: ZTN79 - TN726 - WP90851-L1 - B1 - C1 - C2 - P1 - W1 - Z3A5 ADU - HYBRID LINE CP Figure DATA LINE C P MODULAR Y ADAPTER TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D8W-87) OCTOPUS CABLE (WP90780) KS22911 POWER SUPPLY INSIDE WIRING CABLE EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA CORD 7300H SERIES VOICE TERMINAL 2-40. 7300HSeriesTerminal/ADU Con[...]

INSTALLATION Off-Premises Stations (TN742, TN746B in R3V2) An FCC-registered single-line terminal may Station (OPS). Note: Only the local telephone interconnections for the OPS. be installed as an Off-Premises company can install the The connections between the network interface and the 700A Jacks are described under “Connect Network Interfaces t[...]

INSTALLATION 4. Connect the cable to a protection device at the System 25 location. 5. Connect the second protection device to an 858A Adapter on the617A Panel, using 4-pair inside wiring cable. 6. Connect the 858A Adapter to a port on a TN742 circuit pack using an octopus cable. Out-of-Building Voice Terminals (ZTN79) Transmission facilities (voic[...]

INSTALLATION H600 307 .G 2 CONNECTO R CABLE (NOTE ) TO D4 CHANNE L BAN K NOTE; FOR DISTANCES OVER 50 FEET (15.2 M) USE C6E CONNECTOR CABLE(S) BETWEEN H600 307 .G2 CONNECTOR CABLE AND DS1 TRUNK CIRCUIT PACK . TO LOCALL Y PROVIDED -48 V POWER SUPPL Y Figure 2-41. DS1 to D4 Connections for Off-Premises Stations 2-97[...]

INSTALLATION Stand-Alone Data Terminals Data terminals and computers may be connected to the system through ADUs or a Multiple Asynchronous Data Unit (MADU) without being linked to a voice terminal. Depending on the data terminal that they connect to, some ADUs may need supplementary power for proper operation. See Figures 2-42 and 2-43. ADU Connec[...]

INSTALLATION LEGEND : . B1 - TYPICAL - 103A CONNECTING BLOCK C1 –MODULAR CORD (D8W-87) C7–MODULAR POWER CORD (D6AP-87) W 1 -4-PAIR INSIDE BUILDING WIRING CABLE 248B ADAPTER-ALLOWS MODULAR JACK CONNECTION FROM 2012D TRANSFORMER 400B2 ADAPTER-POWER ADAPTER 2012D TRANSFORMER - 15-18V AC TRANSFORMER Z3A1 ADU -EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA C[...]

INSTALLATION LEGEND : TN726 -DATA LINE CP B1 - TYPICAL - 103A CONNECTING BLOCK Cl -MODULAR CORD (D8W-87) C7-MODULAR CORD (D6AP-87) P2-MODULAR BULK POWER SUPPLY POWER UNIT (346A) POWER PANEL (346A-1) W1 -4-PAIR INSIDE WIRING CABLE Z3A1 ADU -EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA CORD Z3A4 ADU -EQUIPPED WITH A 3 FOOT RECEPTACLE-ENDED EIA CORD Figure 2[...]

INSTALLATION MADU Connections The MADU provides a direct connection to a host computer or a large group of data terminals (64 maximum). See Figure 2-44. The MADU has eight port connectors; each port is equivalent to a single ADU. Complete installation instructions for the MADU are contained in the MADU Product Guide (999- 700-525). SYSTEM 25 CABINE[...]

INSTALLATION INSTALL CUSTOMER’S SAT The SAT can be connected through the SIP to the CPU/Memory CP by any one of the following methods: l On-premises nonswitched connection (no ADU required if the SAT is plugged into the system AC outlet) l On-premises switched connection l Off-premises nonswitched connection l Off-premises switched connection. SM[...]

INSTALLATION LEGEND : ZTN129-CPU/MEMORY CP C1 -MODULAR CORD (D8W-87) C2 -OCTOPUS CABLE (WP90780) 355A ADAPTER -RS-232 PLUG TO MODULAR JACK 355AF ADAPTER -RS-232 RECEPTACLE TO MODULAR JACK * PERIPHERAL EQUIPMENT ● SYSTEM ADMINISTRATION TERMINAL (LEG 1 OF OCTOPUS CABLE) ● DIGITAL TAPE UNIT (LEG 3 OF OCTOPUS CABLE) ● SMDR OUTPUT DEVICE (LEG 2 OF[...]

Nonswitched See Figure 2-46. Connection of Equipment Note: Figure 2-46 shows an Z210A1 SIP Adapter to provide the building wiring termination. An 858A Adapter can also be 1. 2. 3. 4. 5 . 6 . 7 . 8. 9 . 10. used. Connect the RS-232C plug on the peripheral 232C port on a Z3A1 or Z3A4 ADU. Alway s other fasteners on this connection. equipment to the R[...]

INSTALLATION LEGEND : B1 –TYPICAL - 103A CONNECTING BLOCK C1 -MODULAR CORD (D8W-87) C2 -OCTOPUS CABLE (WP90780) C3-EIA CROSSOVER CABLE (P17U-87) C4 -MODULAR RECEPTACLE TO MODULAR PLUG ADU CROSSOVER (D8AM-87) C7-MODULAR POWER CORD (D6AP-87) W1 -INSIDE BUILDING WIRING CABLE 248B ADAPTER-ALLOWS MODULAR JACK CONNECTION FROM 2012D TRANSFORMER 355AF AD[...]

INSTALLATION On-Premises Digital Switched Connection To access a CPU/Memory port through a switched connection, the port is connected to a port on a TN726 CP and assigned a Data Dial Code (DDC). See Figure 2-47. The peripheral equipment can be either stand-alone or associated with a voice terminal. The peripheral equipment is connected to another p[...]

INSTALLATION 11. Connect the other end of the modular cord to a 355AF Adapter. 12. Connect an M7U-87 Cord to the 355AF Adapter. 13. Connect the other end of the M7U-87 Cord to the RS-232C jack on a Z3A4 ADU . 14. Connect the ADU to a 400B2 Adapter with a D8W-87 cord. 15. Connect the 400B2 Adapter to a 2012D Supplementary Power Unit as shown in Figu[...]

INSTALLATION LEGEND: B1 - TYPICAL - 103A CONNECTING BLOCK cl - MODULAR CORD (D8U-87) C2 - OCTOPUS CABLE (UP80780) C3 - EIA CROSSOVER CABLE (M7U-87) C7 - MODULAR POUER CORD (D8AP-87) W1 - INSIDE 8UILDING WIRING CABLE 2488 ADAPTER - ALLOW MODULAR JACK CONNECTION FROM 20120 TRANSFORMER 355AF - ADAPTER (RS-232 RECEPTACLE TO MODULAR JACK) 40082 ADAPTER [...]

INSTALLATION Off-Premises Nonswitched Connection Off-premises peripheral equipment must be equipped with an originating modem (see Figure 2-48). The connection is made from the CO through the TAE to a dedicated modem (optioned for autoanswer) connected to the appropriate Call Processor port. 1. 2. 3. 4. Following the instructions for connecting off[...]

INSTALLATION SYSTEM 2 5 CABINE T PART O F OCTOPU S CABL E CO OR PROVATE LINE CIRCUIT PART OF SI P CONNEC T VIA TA E ZTN12 8 OR ZTN13 0 Z210A 2 ADAPT. TYPICAL MODE M TELC O CENTRA L OFFIC E 355A F *PERPPHERAL EQUIPMEN T TYPICA L MODE M LEGEND: ZTN129/130 - CPU/MEMORY CP C1 - MODULAR CORD (D8W-87) C2 - OCTOPUS CABLE (WP90780) C3 - EIA CROSSOVER CORD [...]

INSTALLATION INSTALL CUSTOMER’S DTU The DTU must be directly connected to Port #3 on the CPU/Memory CP (Figures 2-45 and 2-46). Remote and switched connections are not supported. Follow the procedures provided for installing the SAT. INSTALL STATION MESSAGE DIGITAL RECORDING (SMDR) EQUIPMENT The SMDR equipment connects to Port #2 on the CPU/Memor[...]

INSTALLATION INSTALL STARLAN NETWORK INTERFACE Note: Support for the STARLAN Interface has been discontinued. The ZTN84 STARLAN Interface CP provides an interface between the System 25 TDM bus and a STARLAN NETWORK local area network (LAN). An octopus cable connects the ZTN84 CP to a Network on the STARLAN NETWORK (Figure 2-49). 1. 2. 3. 4. Select [...]

INSTALLATIO N Shared System 25 Voice/STARLAN NETWORK Data Connections STARLAN NETWORK workstations can share the 4-pair System 25 wiring to the SIP with an analog or 7300H Series voice terminal. The STARLAN NETWORK data is transmitted over pairs two and three. At the SIP, the data pairs and voice pair(s) are separated by the standard Y-adapter (WP9[...]

INSTALLATION STARLAN NETWORK NEU PART OF SI P SYSTEM 25 CABINE T Y ADAPT (WP90851- L1 ) SI P ADAP T (TYP ) ZTN7 8 O R TN74 2 PART OF OCTOPUS CABL E PERSONA L COMPUTER STARLAN NETWORK WORKSTATIO N LEGEND : ZTN78 - TN742 - 699Y - B1 - C1 - C2 - C5 - W1 - MP90851-L1 - NOTES : 1. 2. IF RANGE IS TIP RING LINE CP ANALOG LINE CP ATL ADAPTER TYPICAL - 103A[...]

INSTALLATION 73001H Series Voice Terminals See Figure 2-51. 1. 2. 3. 4. 5. 6. 7. Unpack each terminal and examine it for damage. At the workstation, use a D8W-87 modular cord to connect the NAU jack on the KS-23475, L1 Adapter to the OUT jack on the NAU. Using a D8W-87 modular cord, connect the PHONE jack on the KS- , 23475, L1 Adapter to the voice[...]

INSTALLATION LEGEND: ZTN79 - WP90851-L1 - A2 - B1 - C1 - C2 - C3 AND C4 - P1 - W1 - Figure 2-51. HYBRID LINE CP MODULAR Y ADAPTER KS-23475 ADAPTER TYPICAL - 103A CONNECTING MODULAR CORD (D8W-87) OCTOPUS CABLE (WP90780) MODULAR CORDS BUILT INTO KS-23475 ADAPTER KS-22911 POWER SUPPLY INSIDE WIRING CABLE I PERSONAL COMPUTER STARLAN NETWORK WORKSTATION[...]

INSTALLATION INSTALL MUSIC-ON-HOLD INTERFACE Note: Use of equipment that rebroadcasts copyrighted music or other material may be required to obtain a license from a third party such as ASCAP or BMI. FCC-Registered Music Source Interface The music source is connected to a ZTN78 CP through the SIP (see Figure 2-52). 1. 2. 3. 4. Using an octopus cable[...]

INSTALLATION LEGEND : TN742 – ZTN78 – B1 - C2 - C5 - W1 – MOH - ANALOG LINE CP TIP RING CP TYPICAL - 103A CONNECTING BLOCK OCTOPUS CABLE (WP90780) PEC 2720-05P MODULAR CORD (D4BU-87) INSIDE WIRING CABLE KS-23395 INTERFACE Figure 2-52. Music Source, FCC Registered 2-118[...]

INSTALLATION Non-FCC Registered Music Source Interface The music source is connected to a ZTN78 CP (see Figure 2-53). Connect the CP to a 858A Adapter at the SIP. Follow the instructions for installing FCC-registered equipment. You must also install a kit-of-parts (D-181575; includes 36A Voice Coupler, 201213 transformer, and KS-23395 MOH interface[...]

INSTALLATION Music Source (Customer supplied) Music-on-Hold interfac e (KS-23395 ) G R GR GR MSH I ❑ ❑ ❑ (Optional) DW8A-SE 909A/ B Univversal Coupler (Replaces 36A Voice Coupler) MSHI CT CT J 2 MSLO MSLO CR C R Twisted Pair 26AWG Min. PR R J 1 PT T T System 25 DW8A-SE J 3 ZTN78 Circuit Pac k 858 A Adapter -48V GRD -48d c Power Source WP-9078[...]

INSTALLATION 2-119b This page intentionally left blank. November 1995[...]

INSTALLATION INSTALL EXTERNAL ALERTS External 54). 1. 2. 3. alerts are connected to the system through a ZTN78 CP (Figure 2- Connect the CP to a 858A Adapter at the SIP. Connect the other side of the adapter to a 103A Connecting Block using building wiring. Connect the block and alerting device with a D4BU cord. LEGEND : TN742 - ANALOG LINE CP ZTN7[...]

INSTALLATION INSTALL RECORDED DELAY ANNOUNCEMENT Dela y announcements are installed the same way as external alerts. INSTALL DICTATION SYSTEM INTERFACE If the equipment does not require a contact closure, follow the instructions for installing external alerts. If the equipment requires a contact closure, follow the instructions below for connecting[...]

INSTALLATION Direct Connection to TN763 Auxiliary Trunk CP Paging (Figur e ● ● equipment can be connected directly to a TN763 Auxiliary Trunk CP 2-55) when the following conditions exist: Paging equipment is FCC registered. Paging equipment requires a contact closure Connect as shown in Figure 2-55, following the steps 1. Connect the CP to a 66[...]

INSTALLATION SYSTEM 2 5 CABINE T PART O F 25 PAIR CABL E PART O F 66-BLOC K A W 1 C 5 TN76 3 B 1 < PAGING O R DICTATION SYSTE M LEGEND : TN763– AUXILIARY TRUNK CP A – SINGLE-ENDED 25 PAIR CONNECTOR CABLE (A25D) B1 - TYPICAL - 103A CONNECTING BLOCK C5 -MODULAR CORD (D4BU-87) W1 - INSIDE WIRING CABLE (4-PAIR) NOTE : Figure APPARATUS CODE D-181[...]

INSTALLATION Connection to TN763 Auxiliary Trunk CP (278A Adapter Required) A 278A Adapter is required to connect paging equipment to a TN763 Auxiliary Trunk CP (Figure 2-56) when the following conditions l Paging equipment is not FCC registered. l Paging equipment requires a contact closure Connect as shown in Figure 2-56, following the steps 1. 2[...]

INSTALLATION Loudspeaker Syste m Cros s Connect Fiel d Red 103A o r Wal l Jack Green Line Cord B25 A o r A25 D Auxiliary Cabinet or Wall Field T 25-Pair F Conn. on ED- 1E443- 1 0 Pane l T R 909A/B Universal Coupler 25-Pair F Conn. on ED- 1E443- 1 0 Pane l PG1/BZ 1 BSY1/BY1 BSY2/BY2 PG2/BZ 2 CMS2/M2 CMS1/M1 Musi c Source -48 V D C Power Supply PWR G[...]

INSTALLATION This page intentionally left blank. 2-124b November 1995[...]

INSTALLATION 5. 6. 7. 8. 9. 10. 11. Set switch to NORMAL position. Using a D4BY (single-ended) modular cord, connect D-181321 kit of parts (Figure 2-56) to a KS-22911, L2 power supply (-48V dc). Connect terminals -V and GRD on 278A adapter to D-kit. If background music is desired, connect terminals Ml and M2 on the 278A Adapter to the customer-prov[...]

INSTALLATION LEGEND : TN763 - AUXILIARY A - B1 - C5 - C6 - P1 - W1 - 278A SINGLE-ENDED TRUNK C P 25 PAIR CONNECTOR CABLE (A25D) TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D4BU-87) SINGLE-ENDED MODULAR CORD KS-22911, L2, POWER SUPPLY, -48 VOLT DC INSIDE WIRING CABLE (4-PAIR) ADAPTER -REQUIRES –24 VOLT ZENER DIODE KIT OF PARTS NOTES : 1. APPARAT[...]

Figure 2-57. 278A Adaptor Plug Positions for Connecting TN763 Circuit Pack to Paging System 2-127[...]

INSTALLATION Connection to ZTN76 or ZTN77 CP PagePac 20 system with ZoneMate 9/39 and Common Control Unit (CCU) provides up to nine/thirty-nine paging zones and multizone groups. To connect a PagePac 20 system, make connections using the following steps (Figure 2-58): 1. 2. 3. 4. 5. 6. 7. Place the PagePac amplifier on the ZoneMate and the CCU. Con[...]

INSTALLATION LEGEND : ZTN76 - ZTN77 - A - B1 - C5 - W1 - GROUND START C’ LOOP START C’ 3 TO 1 SPLITTER CABLE (WP-90929,L1) TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D4BU-87) INSIDE WIRING CABLE (4-PAIR) Figure 2-58. PagePac 20 System Connection to ZTN76 or ZTN77 Circuit Pack 2-129[...]

INSTALLATION Customer-provided paging equipment can also be connected to ZTN76 or ZTlN77 CO trunk CPs. Connection to the system is made through the TAE appearance of the Tip/Ring pair of the CO trunk CP (See Appendix A for connection details). A paging equipment interface kit D-181900 consisting of a Universal Telephone Access Module (UPAM) and a -[...]

INSTALLATION LEGEND : ZTN76 - GROUND START CP ZTN77 - LOOP START CP A - 3 TO 1 SPLITTER CABLE (WP-90929,L1) UPAM - UNIVERSAL TELEPHONE (PAGING) ACCESS MODULE P 1 - PRS-48 POWER SUPPLY W1 - INSIDE WIRING CABLE (4-PAIR) NOTES : 1. APPARATUS CODE D-181523 INCLUDES 66E3-25 BLOCK CONNECTOR AND CABLE B25A 15/DE. 2. APPARATUS CODE 0-181900 INCLUDES UPAM A[...]

SYSTEM TESTS SYSTEM TESTS Once installation is completed, the system must be initialized, following the procedures in the AT&T System 25 Administration Manual (555-540-500). When this has been done, the system is ready for acceptance testing. You should test all trunks, voice terminals, data terminals, and features. If any equipment does not pe[...]

SYSTEM TESTS TEST INCOMING DID TRUNKS You can test DID trunks by establishing a connection on each DID trunk and then busying it out so that all DID trunks can be tested. 1. 2. 3. 4. 5. 6. 7. At a working voice terminal, go off-hook, dial the CO trunk access code, and then dial a DID number. You should hear ringback at the calling terminal and ring[...]

SYSTEM TESTS 4. Repeat Steps 1 through 3 for all incoming tie trunks, and make sure each tie trunk is tested. TEST 7300H SERIES VOICE TERMINALS Test each 7300H Series terminal using the terminal’s test switch, by placing both station-to-station and external calls, and by using the feature buttons. 1. 2. 3. 4. 5. 6. 7. Push the T/P switch on the l[...]

SYSTEM TESTS 8. 9. 10. 11. 12. 13. 14. Dial the Dial the central office (CO) trunk access code. You should hear the CO dial tone. listed directory number for the system you are installing. You should hear ringback at the calling terminal and ringing at the attendant console. Go off-hook at the attendant position, and verify transmission. At the cal[...]

SYSTEM TESTS TEST SINGLE-LINE VOICE TERMINALS Test each single-line voice terminal by placing station-to-station and external calls. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. At the test terminal, go off-hook. — You should hear system dial tone. Dial the PDC of another working terminal. A t A t A t You should hear ringback at the calling terminal and ri[...]

SYSTEM TESTS TEST ATL CORDLESS TELEPHONE The ATL Cordless Telephone must be tested to see The transmission quality must be verified when the separated by the maximum operating distance. if it functions properly. base and handset are Use the documentation provided with the ATL Cordless Telephone to perform the required tests. TEST DIAL ACCESS CODES [...]

SYSTEM TESTS 2. 3. 4. 5. 6. At any multiline voice terminal, go off-hook, dial the ARS access code, and dial one of the long-distance numbers. Make sure that the call is completed before going on-hook. Repeat Step 2 if additional long-distance numbers must be called. At the SMDR printer (or SAT), verify that the call was placed over the correct tru[...]

1. 2. 3. 4. Test PDC Login At a voice terminal, go off-hook and dial * * PDC PDC, where PDC is a PDC other than that of the test terminal. — You should hear a confirmation tone. At another voice terminal, go off-hook and dial the PDC that was logged into the first terminal. You should hear ringing at the first terminal. At the home voice terminal[...]

SYSTEM TESTS TEST ATTENDANT CONSOLE Testing the attendant console is the same as testing a multiline voice terminal, except for testing the console’s unique feature buttons. 1. Perform all the steps in “Test 7300H Series Voice Terminal” in this section. 2. Verify that all attendant features are 3. If any features are not working or translatio[...]

SYSTEM TESTS TEST DATA TERMINAL DIALING FEATURE Perform this test on all data terminals and personal computers connected to the system through ADUs. 1. 2. 3. 4. 5. 6. 7. Make sure the test terminal is on. Press <BREAK> <RETURN>. The command mode menu is displayed. (The command mode menu may be displayed before you press <RETURN>.)[...]

SYSTEM TESTS MAKE POOLED MODEM TEST CALL Skip this test if the system does not include a TN758 Pooled Modem CP. This test involves placing a data call from a data terminal connected through an ADU from a data terminal or personal computer connected via a modem (the modem may be part of a terminal connected to System 25 or off premises). Place the c[...]

SYSTEM TESTS TEST EXTERNAL ALERT (NIGHT SERVICE) Place a sounds alerting alerting 1. 2. 3. 4. 5. 6. 7. 8. test call to the attendant console to verify that the alerting device when device device At the the attendant console is in the Night Service mode. If an has not yet been installed, connect a spare voice terminal or to the modular jack reserved[...]

SYSTEM TESTS TEST DICTATION SYSTEM ACCESS Place a call to verify that dictation equipment can be accessed. If dictation equipment has not been installed, this feature cannot be tested. 1. 2. 3. 4. 5. Use a working voice terminal as the test terminal, and go off-hook. Dial the access code or PDC, and the number associated with the dictation equipmen[...]

SYSTEM TEST TESTS MUSIC-ON-HOLD Verify that music is provided to outside callers placed on hold. (Inside callers do not receive Music-on-Hold [MOH].) 1. 2. 3. 4. 5. At any working voice terminal, go off-hook. Dial the CO trunk access code and the system’s listed directory number, or if DID, dial any station. At the called At the called The statio[...]

SYSTEM TESTS TEST EMERGENCY TRANSFER Place the system in emergency transfer mode by turning power off (or remove the modular connector from the ETU). Place an outside call from each emergency transfer station. 1. 2. 3. 4. 5. 6. 7. 8. At Cabinet 1, turn the power off using the rocker switch on the back or remove the modular connector from the ETU. F[...]

SYSTEM TESTS TEST TOUCH-TONE RECEIVERS 1. 2. 3. At a single-line voice terminal, go off-hook. Dial *3 and the 2-digit number (01 through 12) of the touch-tone receiver to be tested. Receivers 01 through 04 are on the ZTN85 or ZTN131 (R3) CP. Receivers 05 through 12 are only present if your system has two TN748 CPs (05 through 08 receivers on one, a[...]

MAINTENANCE MAINTENANCE The primary maintenance objective is to detect, report, and clear troubles as quickly as possible with minimum disruption to normal service. Periodic system self-tests, automatic software diagnostic programs, and fault detection hardware are several of the maintenance tools used to achieve this objective. Most troubles in Sy[...]

MAINTENANCE EQUIPMENT NEEDED The any maintenance technician System 25 service call: should take the following tools and equipment on EIA breakout box Digital voltmeter (KS-20599 or equivalent) 11 O/66-type punchdown tool (AT 8762D or equivalent) Dracon TS21 or equivalent touch-tone test set Assorted flat-head screwdrivers Assorted Phillips-head scr[...]

MAINTENANCE Precautions Electromagnetic fields radiating from the system cabinets may generate noise in other communications equipment. The technician must be sure that all cabinet panels and covers are securely in place after performing maintenance. Caution: Electrostatic discharge can destroy or severely damage integrated circuits on CPs. The mai[...]

MAINTENANCE GENERAL MAINTENANCE INFORMATION System Errors and Alarms During periodic testing, a maintenance audit could detect a system error that automatically generates an error record. Depending on severity, the error record is stored in one of following three tables in the Error Log: ● Permanent System Alarms ● Transient System Errors ● M[...]

MAINTENANCE Memory (ZTN81 [RIV7] or ZTN127 [RI V2]J: The red LED on this CP lights when power is applied and goes dark upon successful completion of the ROM checksum test initiated by the Call Processor CP. Failure is indicated by a steadily lighted red LED. Call Processor [ZTN82 (R1V1) or ZTN128 (R1V2)]: The green LED on this CP lights when power [...]

MAINTENANCE Attendant Console LED A lighted green Alarm LED on the console indicates the presence of a Permanent System Alarm. The LED flashes with each new alarm. The attendant can press the associated button to cause the LED to light steadily. A lighted red Alarm LED indicates a barrier code violation. Power Supply LED A lighted green LED on the [...]

MAINTENANCE Using RIMS, the remote administrator can initialize translations after the switch itself is installed. As long as there is no hardware change, the remote administrator can do ongoing administration without having to visit the customer’s site. Similarly, to trouble-shoot a problem, a technician can call the RIMS port and check the Erro[...]

MAINTENANCE Administration Requirements For a RIMS call to be made during initialization, at least one voice station and one trunk must be translated. A cold start with defaults provides these translations. The RIMS transfer code (*1 00) can be assigned to a Repertory Dialing feature button on a multiline voice terminal. If the Remote Access featur[...]

MAINTENANCE MAINTENANCE STRATEGY Fault isolation is the cornerstone of the System 25 maintenance strategy. Maintenance activity isolates faults to one (or more) repairable or replaceable maintenance units. Equipment should be tested in the following order: 1. 2. 3. 4. 5. 6. Terminal equipment Station wiring Port circuit packs (CPs) Common control c[...]

MAINTENANCE SYSTE M TROUBL E REPORTED USER-REPORTED DISCUSS THE TROUBLE WITH SYSTEM USERS CAP ALARM REPORTED CAP ALARMED READ PERMANENT SYSTEM ALARMS TABLE IN ERROR LOG : AND CHEC K CIRCUIT BOARDS AND POWER LED STATUS SYSTEM OR CANNOT ACCESS ERROR LOG DEFECTIVE POWE R SUPPL Y CHECK POWE R LED AND FAN S READ (1) PERMANENT SYSTEM ALARMS, (2) TRANSIEN[...]

MAINTENANCE Sometimes, faults recorded in the error log and user-reported troubles will exist at the same time. The logged faults should always be cleared first, if possible. This procedure often clears the user-reported troubles without any additional maintenance. Clearing the most serious logged fault may clear some or all of the other faults. De[...]

MAINTENANCE Common Control Problems Common Control circuitry is difficult to troubleshoot. The system must be powered down before any of these CPs are replaced. Before powering the system down, save translations to tape (see “Using the Digital Tape Unit”). Other repair procedures may also require the system to be powered down. After removing a [...]

MAINTENANCE Station, Wiring, and Trunk Problems If the system indicates that a fault is with a station, or if a user complaint indicates a station problem, the trouble must be isolated to the station itself or to the wiring between the cabinet or station interconnect panel and the station. The station wiring, particularly the mounting cord, should [...]

MAINTENANCE USING THE DIGITAL TAPE UNIT The Model DC4 Digital Tape Unit (DTU) or equivalent is extremely important in system maintenance. System Translations are stored in the DTU and can be accessed in the unlikely event that translations are lost during a system failure . This section covers the following: ● Setting Up the DTU ● Saving Transl[...]

4. Press the REWIND button, and wait for the unit to tape. This step ensures that the tape is played from Note: The system automatically compensates for “leader” material at the beginning and end of the Saving Translations Follow these steps to save 1. 2. 3. 4. 5. 6. 7. 8. translations on tape: MAINTENANCE fully rewind the the beginning. the cl[...]

MAINTENANCE 9. 10. Press c to continue, and the tape unit is automatically started by the system. Saving translations on tape takes about 5 minutes and does not affect switch performance. When the save is complete, the unit stops automatically. If the save is successful, the SAT displays: SAVE COMPLETED SUCCESSFULLY. Press the REWIND button and rew[...]

MAINTENANCE 5. 6. 7. . 8. 9. 10. Enter 2. The system responds with: Save/Restore: Action=2 Data=. Enter D. The system completes the word Data followed by the = sign. Enter 1. The system responds with the complete line: Save/Restore: Action=2 Data=1 W25: YOU ARE ABOUT TO START A TAPE VERIFY c for continue, any other key for abort Press c to continue[...]

MAINTENANCE Restoring Translations Note : Restoring translations from tape removes the system from operation for about 5 minutes. When it is necessary to restore system translations from tape, follow these steps: 1. 2. 3. 4. 5. 6. 7. Complete the steps under “Setting up the DTU,” using the cassette on which translations were saved. Press the PL[...]

MAINTENANCE 8. 9. 10. 11. Press c for continue, and the tape unit is automatically started by the system. Restoring translations takes about 5 minutes. When restoration is complete, the unit stops automatically. If restoration is successful, the SAT displays: (feature code issue, date, time, size) followed by: RESTORE COMPLETED SUCCESSFULLY Initiat[...]

MAINTENANCE ROUTINE MAINTENANCE The following are general trouble-clearing techniques usually required to resolve system-detected and/or user-detected troubles. ● Reseating and Replacing Circuit Packs ● Removing and Restoring Power ● Restarting the System. Reseating and Replacing Circuit Packs Except for the CPU/Memory and Service CPs, power [...]

MAINTENANCE 6. Inspect the cabinet backplane and the connectors at the back of the CP. It may be possible to clean dirty connectors per prescribed procedures and return the CP to service. However, if any connectors are damaged or corroded the CP should be replaced. 7. Rest the CP on a firm nonconducting surface, and press in all socketed devices on[...]

MAINTENANCE Removing and Restoring Power When the following procedures are performed, the system must be unplugged from the ac power source: ● ● ● ● Reseating or replacing the Service Circuit or CPU/Memory CPs Replacing the frontplane ribbon connector between the Call Processor and Memory CPs (Release 1 only) Replacing the power supply Repl[...]

MAINTENANCE Restarting the System The system automatically warm starts after power is restored. (The system’s maintenance software may restart the system under certain self-detected error conditions. ) There are two types of restart: cold and warm. A Cold Start and limited cold start (which takes about 4 to 5 minutes) causes the system to check a[...]

MAINTENANCE 6. 7. 8. 9. Enter 9 (for the SAVE/RESTORE selection) and press <RETURN>. The system responds with: Action = Enter 10 for a warm restart. The system responds with: Save/Restore: Action=10 Data=. Enter D. The system responds with: Data = 10. Enter 1. The system responds with: Save/Restore: Action=10 Data=1 YOU ARE ABOUT TO FORCE A W[...]

MAINTENANCE Messages displayed on the SAT indicate which restart is being performed. The same type of information is displayed for a cold and a warm restart. This information consists of a listing of the version of the firmware loaded in the CPU/Memory CP and a configuration The CPU/Memory CP is not listed in be located in slot 1 of Cabinet 1. Tabl[...]

MAINTENANCE The SAT message for a cold restart appears after the system has performed all self-tests and reading of its configuration. The time required for a cold start depends on the number of CPs in the system but is generally several minutes. A typical Release 2 cold restart SAT message is as follows: RESTART TS ROM pair FC ROM pair FC ROM pair[...]

MAINTENANCE ERROR LOG When a system maintenance object fails periodic testing, the system automatically generates an error record. Depending on severity, the record is stored in one of three tables in the Error Log. The Error Log contains the following three error tables: ● Permanent System Alarms : These are failures that cause degradation of se[...]

MAINTENANCE A typical error record from the Permanent System Alarms and Transient System Errors table is as follows: PERMANENT SYSTEM ALARMS PORT BOARD FIRST LAS T COUNT NAME NUMBER CODE OCCURRED OCCURRED 10400 ZTN130 23/12:30 Interpret this record as follows: ● “Port Number” 10400 specifying the location 30/01:5 6 1 Port Board missing But Ad[...]

MAINTENANCE Error records in the Most Recent System Errors table have a slightly different format. A typical error record from the Most Recent System Errors table is MOST RECENT SYSTEM ERRORS POR T BOARD DATE TIME NAM E NUMBER CODE OCCURRED OCCURRED 30300 ZTN131 03/12/85 2:01:56 Port Board Missing But Administered Interpret this record as follows: [...]

MAINTENANCE The Error Log is under the control of internal background maintenance software that automatically escalates an error to a more serious category or retires it. The system tests itself after a repair has been made. If the error condition is corrected, the error may be removed from the Error Log. Although some errors are automatically reti[...]

MAINTENANCE 9. 10. 11. 12. . If you Enter 1 and press <RETURN>. The SAT displays: SEARCHES: ACTlON=1 DATA= Enter D. The system completes the word Data followed by the = sign. After Data= enter one of the following numbers, depending on which error table you wish to see: ● 30 to see Permanent System Alarms ● 31 to see Transient System Erro[...]

MAINTENANCE ERROR MESSAGES Error messages, along with the alarm indicators, are the most likely indicators that an error has occurred in the system. When a maintenance object fails periodic testing, the system automatically generates an error record. The error record (log) is accessible through the SAT. The following table lists and describes error[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTIO N AC Power Failure: An indication Check plug at wall receptacle. If that ac power has been lost (for this error occurs more often than example, plug removed from a the building power outages, check wall receptacle, building power connection to wall. down for more than a quarter of a second,[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Bad Port: (STARLAN Interface Recoverable; no action required. CP) This error is an isolated transient condition. Bad Ringing Supply: Problems Check ring voltage on associated detected with ringing portion of power supply (see Figure 4-2). power supply. Belated External Release: Se e Normal[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION D C Fai l Transien t Record : No action required; this error Indicates a dc power failure. display is a record of the start time of the failure. DC Power Failed: Indicates the Check the +5 V dc voltage level absence of +5 V dc on a cabinet. on the power supply (see Figure Each cabinet has [...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION DXS Reset; The DXS console has Recoverable; no action required. been reset. Electronic Powe r Feed Off , Check the wiring for shorts from Overcurrent: A Hybrid Line the backplane/SIP up to the (ZTN79) port EPF chip shut down. phone jack. Check the ATL set at Two ports are effected, for the[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION External Stack Full: (STARLAN If the reset is not successful Interface CP) This error resets the reseat board. If the reseat fails, CP . replace the board. Fault o n Outgoing Seizure: Check trunk for slow dial tone; ZTN76/TN747 CO ground was not more than 10 seconds. Perform detected withi[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Illegal Instruction: This error is The Problem could be with the logged when an illegal instruction ROM on the CPU/Memory CP. If is encountered by the CPU. the problem persists, check or replace CP. Illegal Interrupt: CPU/Memory CP The CP may still pass the power- problem. up test for the [...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Invalid Message Length: The port If the problem persists, check or CP sent an up-link message that replace the port CP. is not in the expected message set. Invalid Port Board: (Other than Remove or replace CP with a CPU or Memory) Port CP not board that is supported by System supported by [...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Memory Management Error: Bu s Possible softwar e error. If error that occurs while accessing problem persists, check o r the “other than protected” RAM. replace CPU/Memory CP. A A warm start is logged after this warm start or retranslation of the error . system could be a possible fix [...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION On-HookBeforeReady To Receive Digits: For a tie trunk with delay dial or wink start—after the handshake is complete, a 50-ms guard time must pass before digits are received. If the far-end goes on-hook before guard time elapses, this message is logged. On-Hook Before Wink: For a tie trun[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Port CP Missing Bu t Check CP slot; reseat CP; change “Administered: (Other tha n CP; or remov e C P fro m CPU/Memory) Translated port CP translations. If CP does not pass that CPU cannot access. power-up, replace CP. Port CP Out Of Service: (Other If the CP has not been removed than CPU[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Received Incorrect Number of DID Digits: This error indicates that the CO is set up to send a number of DID digits different from what the switch has been administered to receive. Ensure that trunks are properly translated. Notify local CO to verify the correct number of digits to be sent.[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Servic e Circuit Test Failed: Check TDM bus terminator and Service Circuit demand test failed cabinet interconnect cables. If the on the DTMF receivers. problem persists, replace ZTN85 or ZTN131 (R3). Signaling Lead Fault: Auxiliary Chec k wiring of externa l Trunk CP is expecting a ground[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Trunk Call Dropped: A call that Normally, no action required; had been up on a trunk for more however, if problem persists, than 9 hours has been detected perform trunk test call per Trunk by an audit and dropped. The Troubles procedure in this Part. port associated with the error Also, ch[...]

MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Unrecognized Command: Recoverable; no action required. (STARLAN Interface CP) This error is an isolated transient condition. User Forced Warm Start: System Recoverable; no action required. was warm started through the SAT. Warm Start: Power supply may be out of System was restarted for som[...]

MAINTENANCE . . Figure 4-2. Clearing Supply Troubles (Sheet 1 of 2) 4-47[...]

MAINTENANCE Figure 4-2. Clearing Power Supply Troubles (Sheet 2 of 2)[...]

MAINTENANCE Figure 4-3. Clearing CO Trunk Troubles 4-49[...]

MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 1 of 4) 4-50[...]

MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 2 of 4) 4-51[...]

MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 3 of 4) 4-52[...]

MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 4 of 4) 4-53[...]

MAINTENANCE NOTES : 1. PC should be running NAUCOM, Session, CAM and/or any STARLAN NETWORK compatible emulating program . 2. The green LED lights when the STARLAN CP passes power up. Figure 4-5. Clearing STARLAN Interface Troubles[...]

Figure 4-6. Clearing Tie Trunk Troubles (Sheet 1 of 5) 4-55[...]

MAINTENANCE [6] [7] [8] [9] [10] Figure 4-6. Clearing Tie Trunk Troubles (Sheet 2 of 5) 4-56[...]

MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 3 of 5) 4-57[...]

MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 4 of 5) 4-58[...]

MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 5 of 5) 4-59[...]

MAINTENANCE Figure 4-7. Clearing Paging Equipment Troubles[...]

MAINTENANCE Clearing System-Detected Troubles Most troubles are detected through the Alarm LED located on the Attendant Console, the Error Log, and, in some cases, the LEDs on the circuit packs (CPs). The following is a list of system troubles. Each item in the list is described in this section. Complete System Failure Common Control Trouble Circui[...]

MAINTENANCE Failure of the CPU/Memory CP at power-up generates the following type of error message: FAIL: <CARD>: <TEST>: <DETAIL>: The bracketed fields contain the following information: ● <CARD> is CPU/Memory ● <TEST> is one of the following: RAM TEST ROM TEST AA INTERFACE DUART TEST REAL-TIME-CLOCK TEST BUS ERRO[...]

MAINTENANCE After total failure, the system ceases to operate and the green LED on the CPU/Memory CP may not flash. Failure can also be verified by checking the LEDS on each CP. If either a partial or total Common Control failure is detected, remove and then restore system power. This procedure forces the system to perform a warm restart. If the fa[...]

MAINTENANCE Once a faulty CP is identified, it can be replaced using the procedures in “Reseating and Replacing Circuit Packs” under “Routine Maintenance. ” Refer to the information in “Circuit Pack LEDs” under the “General Maintenance Information” to understand the meaning of the CP LEDs. . If the Error Log notes an error related t[...]

MAINTENANCE Table 4-B lists the test points (-5 V, +5 V, -48 V, and GND) for the power supply. The test points are located on the upper-right corner at the front of the cabinet. Table 4-C lists the voltages used by the CPs and symptoms voltages are missing. This information is useful in diagnosing power distribution problems. Table 4-B. Power Suppl[...]

MAINTENANCE Table 4-C. Circuit Pack Voltage–Symptoms Voltage/ +5 volts -5 volts -48 Volts Circuit Pack (Notes) No+5 V No-5 V No-48 V Call Proc. (ZTN82, x System Failure x EIA Failure x ETU Activated ZTN1 28) for RI Memory (ZTN81, x System Failure - - - - ZTN1 27) for RI CPU/Memory (ZTN129, x System Failure x EIA Failure x ETU Activated for R2, ZT[...]

MAINTENANCE Each power supply has one green LED on its front that can be seen through the fan assembly. The LED is visible through the ventilation slots on the front cover, but the cover must be removed for diagnostic and service purposes. This LED is always lighted when the system is receiving 5.1 volts power. The LED is dark when there is a failu[...]

MAINTENANCE AC DISTRIBUTION UNIT AC CIR D VARISTOR PWB ASSY CM 538A1 S1 SW TO 15 A 120 VAC OUTLE T GROUND BLOC K Figure 4-8. AC Power Schematic 4-68[...]

MAINTENANCE Power Supply Protection Power supply outputs are protected from damage when they are subjected to either momentary or sustained short circuits. “Shutdown” current protection is provided at 125 percent (plus or minus 5 percent) of full load for each dc output. Current foldback is provided for the 90 V ac output. Output power is remov[...]

MAINTENANCE Power Supply Replacement To replace the power supply, follow these steps: Danger: Hazardous voltages are present on some backplane 1. 2. 3. 4. 5. 6. 7. 8. pins. Unplug power cord from the outlet, and wait at least 5 minutes before removing rear cover or power supply. Remove the front cover of the cabinet. Remove the four No. 6-32 screws[...]

MAINTENANCE Fan Assembly Trouble The fans should always be operating when the system is receiving ac power and the cabinet switch is turned on. If the fans are not operating, be sure that the system is receiving ac power. if the system is receiving power and the fans are still not operating, the ac power connection to the fan assembly is faulty or [...]

MAINTENANCE Overheating Trouble A clogged or dirty air filter can cause the cabinet to overheat. The cabinet air filter rests on the floor of the cabinet under the CP carrier. The air filter should be inspected on any service call and replaced as needed (with air filter comcode 845948348). Caution: To replace the Warning: Check underneath cabinet f[...]

MAINTENANCE TEST POINT CABLE CONNECTS I HERE. ACCESS VOLTAGE TEST ADDRESS PLUG POSITION POINTS FROM FRONT OF (SLOT 08 NOT USED) CABINET. Figure 4-9. System Cabinet Backplane Wiring Side (Sheet 1 of 2) 4-73[...]

MAINTENANCE Figure 4-9. System Cabinet Backplane Wiring Side (Sheet 2 of 2) 4-74[...]

MAINTENANCE Figure 4-10. TDM Signal Designations on Cabinet Backplane 4-75[...]

MAINTENANCE Figure 4-11. Power Designations on Cabinet Backplane 4-76[...]

_ MAINTENANC E Each of the 12 universal carrier slots has 48 pins on the backplane for connection to station and trunk ports. The 48 pins are divided into eight groups of 6 pins each, one group for each port circuit. Lead designations consist of the lead name suffixed by the group number (for example, TA.2, RA.2). Specific functions depend on the t[...]

MAINTENANCE Table 4-D. 25-Pair Connector to Backplane Designations 25-Pin-Conn . Cal l Pro c Pin No. Wir e Colo r G S Trun k ZTN7 6 L S Trun k ZTN7 7 Tip Ring Lin e ZTN7 8 AT L Lin e ZTN7 9 ME T Lin e TN73 5 Backplan e Pin No . (Slots 1-12) 2 6 1 2 7 2 2 8 3 2 9 4 3 0 5 3 1 6 3 2 7 3 3 8 3 4 9 3 5 1 0 3 6 1 1 3 7 1 2 3 8 1 3 3 9 1 4 4 0 1 5 4 1 1 6[...]

MAINTENANCE Table 4-D. 25-Pair Connector to Backplane Designations Contd) 25-Pin-Conn. . Pin No. Wir e Colo r DI D Trun k TN753 Ti e Trun k TN760B Aux . Trun k TN763 Dat a Lin e TN72 6 Analog Lin e TN74 2 Analo g Lin e TN746 B DS 1 Interfac e TN76 7 Backplan e Pin No . (Slots 1-12) 2 6 1 2 7 2 2 8 3 2 9 4 3 0 5 3 1 6 3 2 7 3 3 8 3 4 9 3 5 1 0 3 6 1[...]

MAINTENANCE 8' CABLE LENGTH CONNECTOR 1 CONNECTOR 0 CONNECTOR 2 STOCKLIST DESCRIPTION 25-PR PLU G 8-FT, 8-PR, 24-GC, CABLE 25-PR RECEPTACLE SPACER (NOTE 1) NOTES: 1. 2. 3. INSTALL SPACER AT CONNECTOR CABLE CLAMP TO ENSURE PROPER CABLE RETENTION. ITEMS 1 AND 3 SHALL BE EQUIPPED WITH SCREWS TO FACILITATE ASSEMBLY TO B25A CABLES. LABEL CONNECTORS[...]

MAINTENANCE Emergency Transfer Unit Troubl e If the Emergency Transfer Unit (ETU) will not enter the power failure mode, do the following steps: 1. 2. 3. Unplug the cable bringing the control signal from port 7 or 8 on the CPU/Memory CP to the ETU. This cable terminates in a modular jack that is inserted in a modular plug labeled CPU on the left-ha[...]

MAINTENANCE CLEARING USER-DETECTED TROUBLES User-reported troubles are usually associated with voice or data terminal equipment or trunks. They can result from system-detected errors and are often solved by clearing system error conditions or alarms. This section presents trouble-clearing techniques and procedures for user- reported troubles. Maint[...]

MAINTENANCE Note : For problems with administration equipment that is not connected on a dedicated basis, refer to the Terminal Operations Manual, 555-540-710. Time-Keeping Troubles Symptoms: Clock Procedures: 1. Reset doesn’t reflect current time or date. clock from SAT (see the Administration Manual). Clock has tolerance of plus or minus 3 minu[...]

6. 7. 8. 9. Voice Check CP translations from the SAT to be sure that this CP has Check LEDs on CP. The red LED will be lighted if a fault on the CP affects all ports. Also, the red LED may be lighted if one or a few ports are faulty. Check Error Log for relevant messages. Reseat the CP even if the red LED is dark. (See “Reseating and Replacing Ci[...]

MAINTENANCE 2. 3. 4. If you hear dial tone, continue with this test. Dial the digits 1234567890 *#. Y OU should hear a DTMF signal as each key is pressed. If the test passes, you will hear dial tone within 1 to 3 seconds after you enter #. Repeat the test for each touch-tone receiver. Replace the Service Circuit CP if this test fails. 7300H Series [...]

MAINTENANCE Procedures : 1. Make sure that the appropriate ZTN79 CP is translated. 2. Check for the presence of -48 volts at test point on front of cabinet. Symptoms: Inoperative used. Procedures : 1. If LOCAL display-equipped voice terminal when LOCAL button is button/lamp activate LOCAL button. is off, and voice terminal is inoperative, 2. If ter[...]

MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 1 of 3)[...]

MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 2 of 3) 4-87[...]

MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 3 of 3) 4-8 8[...]

MAINTENANCE Trunk Troubles Many trunk troubles originate in the central office (CO) facilities. The first step in identifying trunk troubles should be to check for presence of dial tone at the Trunk Access Equipment (TAE). If required, check the Error Log records, and make a trunk test call. Note that it is sometimes difficult for the user to detec[...]

MAINTENANCE 5. Listen for dial tone from the accessed trunk. If dial tone is not present, isolate the fault to a trunk port CP or location in the trunk access equipment, etc., using a test set. 6. If dial tone is present, dial a working outside number. Verify that the call is complete. 7. If trunk is busy, fast busy tone is heard. If a nonport trun[...]

MAINTENANCE 6. If “no loop current on outgoing call” is displayed, either of the above conditions could be true. It is more likely, however, that the facility is down . 7. Place an outside call on the line using the trunk test call procedures listed in outgoing Trunk Problems. If you get fast busy tone, switch trunk ports and try again. 8. If t[...]

MAINTENANCE 8. 9. 10. 11. 12. If the problem does not move, replace the Ground Start CP. If the problem moves, the fault is with the CO. Notify CO personnel through the proper channels. If “Ringing no ground” is displayed, the T and R leads may be reversed in the trunk access wiring. The T lead should have ground, and the R lead should have –[...]

MAINTENANCE 3. 4. 5. 6. 7. 8. 9. ● CO failure to release after PBX disconnect ● CO belated release. These messages indicate CO problems. The first three errors are very common when DID trunks are installed. The CO should be notified through the proper channels about any of these problems. The CO failure to release after PBX disconnect can frequ[...]

MAINTENANCE Figure 4-13. Clearing Switched Loop Attendant Console Troubles (Sheet 1 of 5)[...]

MAINTENANCE 4-13. Clearing Switched Loop 2 of 5) Console Troubles (Sheet 4-95[...]

MAINTENANCE Figure 4-13. Clearing Switched 3 of 5) Loop Attendant Console Troubles (Sheet 4-96[...]

MAINTENANCE 4-13. Clearing Switched 4 of 5) Console Troubles 4-97[...]

MAINTENANCE NOTES : 1. (a) System defaults to a DTAC when first powered up. (b) You have to remove the DTAC before you can administer the SLAC . (c) System 25 can support 1 or 2 DTAC or 1 or 2 SLAC but not a combination of both. 2. ID names can be assigned for PDCs, Trunks, FPDCs, and DGC groups. (a) (b) (c) (d) 3. You Under Menu = 1 or 2 (Port/PDC[...]

MAINTENANCE Special Port Circuit Options for Stations and Trunks Tables 4-E and 4-F provide the special port circuit options that are administered in the system. System defaults and associated action codes applicable to the various port CPS are also shown. Procedures are available in the Administration Manual for logging onto the system and accessi[...]

MAINTENANCE Table 4-F. Applicable Actions for Circuit Pack Options ACTIONS FOR CIRCUIT PACK OPTIONS (See Circuit Pack Options—Table 4-E) CIRCUIT CP ACTIONS PACK TYPE 32 33 34 35 36 37 38 , ZTN76 GS Board ● ● ● ● ZTN77 LS Trunk ● ● ● ● ZTN78 Tip/Ring Line ● ● TN742 Analog Line ● ● ● ● TN753 DID Trunk ● ● ● ● TN7[...]

6. 7. 8. 9. 10. 11. 12. 13. 14. If +7 volts are not present, the ADU is not receiving enough power from the data terminal and must be locally powered. If the ADU is powered from a local transformer, make sure that a 3- pair or 2-pair modular cord is connected between the transformer and the ADU. Using a 4-pair modular jack breakout ac voltage betwe[...]

MAINTENANCE Multiple Troubles or Trouble That Cannot Be Diagnosed Symptoms: Red LED is lighted on all port CPs. SAT displays this message: “FAIL : CPU : ARC H ANGEL INSANE: CHECK ZTN85: TERMINATOR?”. Procedures : 1. 2. 3. 4. 5. Check that the TDM bus terminator card(s) is installed in the rear pin field(s) . Note: The CPU/Memory CP provides bui[...]

MAINTENANCE Symptoms : Red LED is lighted cm several port CPs. Procedures: 1. 2. 3. 4. . Check the power supply to be sure that it is providing correct voltages (see “Power Supply Trouble’ ‘). Check the frontplane connector and the CPU/Memory CP, and replace any faulty unit(s). Reseat any CPs where the red LED is still lighted. After reseatin[...]

REFERENCES The following System 25 documents are available for reference. A brief description of each manual is provided. ● Administration Manual ● Advanced Admin User Guide (MS-DOS) ● Advanced Admin User Guide (UNIX) ● An Introduction to AT&T System 25 ● Implementation Manual ● Installation and Maintenance Manual ● Reference Manu[...]

REFERENCES An Introduction to AT&T System 25 Provides an introduction to System 25 features and services. The emphasis is on how System 25 helps solve information management, productivity, and cost control problems. Implementation Manual Describes how to plan the system’s operating configuration. Explains how to determine customer needs and h[...]

REFERENCES Reference Manual This document is the system’s principal technical reference. It provides reference material for sales support, system configuration and operation, and for the system technician. It contains a comprehensive description of the system, emphasizing features, components and overall capabilities and capacities. Integrated So[...]

REFERENCES Call Management System—System Manual Provides information necessary to install CMS software, administer, use, and troubleshoot CMS. Call Management System—lnstallation Guide Provides instructions for inserting the CMS interface card into the PC. Call Management System—Planning Guide Provides detailed information necessary to make d[...]

ABBREVIATIONS AND ACRONYMS ABBREVIATIONS AND ACRONYMS ADU AE ARS ASCII BPS CCS CCSA COS CSU DCE DDC DDD DID DGC DS1 DTAC DTE DTMF DXS EIA ETU FNPA FRL FX HNPA Asynchronous Data Unit Account Executive Automatic Route Selection American Standard Code for Information Interchange Bits Per Second Hundred Call Seconds Common Control Switching Arrangement[...]

ABBREVIATIONS AND ACRONYMS LD N Listed Directory Number LE D Light-Emitting Diode MET Multibutton Electronic Telephone MO H Music-on-Hold NA U Network Access Unit NE U Network Extension Unit NP A Number Plan Area OP S Off-Premises Station PD C Personal Dial Code PD S Premises Distribution System RA M Random Access Memory RN X Private Network Office[...]

APPENDIX A: APPENDIX A: System Wiring Tables Connector Pin Assignments Table A-A lists the lead designations and pin assignments at the 25-pair connectors on the system cabinets. System 25 Building Wiring Table A-B lists the 25-pair and 4-pair cable color codes, voice and data terminal lead designations, and connecting block terminal punch-down inf[...]

APPENDIX A: System Wiring Tables Table A-A. 25-Pair Connector Pin Assignments 25-Pin Corm. Cal l G S L S Tlp Ring ATL MET Backplane Pin No. Wir e Proc. Trunk Trunk Line Line Line Pin No. Color ZTN8 2 N76 ZTN77 ZTN78 ZTN79 TN735 (Slots 1-12) . 26 W-BL RDA T1 T1 T1 T1 T1 102 1 BL-W SGA RI RI RI R1 R1 002 27 w- o CT1 BTI 103 2 o- w DCDA CR1 BR1 003 28[...]

APPENDIX A: System Wiring Tables Table A-A. 25-Pair Connector Pin Assignments (Contd) 25-Pin Conn. DlD Tie Aux. Data Analog Analog TN767 Backplane Pin No. ‘ Wir e Trunk Trunk Trunk Lin e Line Line DS 1 Pin No. Color 3 TN760B TN763_ TN72 6 TM74 2 TN746B Interface (Slots 1-12) . 26 W-BL T1 T1 T-O T1 T1 102 1 BL-W RI RI R-O RI R1 27 w- o T11 SZ-O TX[...]

APPENDIX A: System Wiring Tables Table A-B. Building Wiring 25-Pair Cable 4-Pair Cable Term. Lead Functions 50 0 ATL 7101 A Cordless D-Inside D-Inside Cable Conn. Cable Conn. Ckt. 250 0 7300H RS-232C Color Pi n Color Block No. Series Series Term , code Num. code Term. 1 T T W-BL 26 W-BL 1 R R BL-W 1 BL-W 2 CT w-o 27 w-o 3 CR TXR o-w 2 o-w 4 P- PXT [...]

APPENDIX A: System Wiring Tables Table A-B. Building Wiring (Contd) 25-Pair Cable 4-Pair Cable Term. Lead Functions 50 0 ATL 7101A Cordless D-inside D-lnside Cable Conn. Cable Conn. Ckt. 250 0 7300 H RS-232C Colo r Pin Color Block No . Series Series Term . Code Num. code Term. 6 T T V-BL 46 W-BL 1 R R BL-V 21 BL-W 2 CT TXT v-o 47 w-o 3 CR TXR o-v 2[...]

APPENDIX B: APPENDIX B: Parts Listing The following information may assist you in cross-referencing Apparatus Codes, Comcodes and Price Element Codes (PECs). DESCRlPTI0 N PEC APPARATUS CODE COMCODE Cabinets System 25 Control Unit (R3V2) 6250-031 includes Carrier J58901 A2 L-1 5 (e/w) Power Supply WP90510, L2 40552847 2 Fans Ass’y WP90677, L2 4056[...]

APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE System 25 Control Unit (R1V2) 6250-012 include s Carrie r J58901A1 , L1 (e/w) Power Supply WP90510, L1 40395476 1 Fan Assembly WP90677, L2 84541637 9 Air Filter ------- 84541875 5 Address Plug ------- 84541663 5 TDM Bus Term, AH F-1 10381058 6 Memory CP ZTN12 7 10521217 9 Processor CP[...]

APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Upgrade Kit (R3V1/V2 to R3V3) R3V1/V2 Upgrade Kit 62527N * * CPU/MEM CP ZTN142 107057754 Circuit Packs GS Trunk CP LS Trunk CP TR Line CP ATL Line CP STARLAN Interface CP Analog Line CP MET Line CP DID Trunk CP Tie Trunk CP Aux Trunk CP Pooled Modern CP Tone Detector Data Line CP DS1 [...]

APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Peripheral Equipment Digital Tape Unit 62507 TS-555A 404079436 System Admin. 62508 TI-703 404079428 Terminal (SAT) Voice Terminals and Accessories Direct Extension 62509 23A1-003 e/w 103969424 Selector Console D6AP Cord 102937620 D8W-87 Cord (14ft) 103786802 KS-22911, L1 Power 4032426[...]

APPENDIX B: Parts Listing DESCRIPTION PEC MET Set-BIS Transformer Kit-of-Parts 12-button MET Set MET Adapter Cord 5-Button 7300H Ser VT 10-Button 7300H Ser VT 7300H Ser. HFAI VT 7300H Ser BIS VT With Display 34 But Dlx 7300H Ser VT 7300H Ser BIS VT 7300H Ser Speaker Mod 7300H Ser Headset Adapte r 7300H Ser VT local power 10-Button BIS VT 22-Button [...]

APPENDIX B: Parts Listing DESCRIPTION Acoustic Coupler Single-Line VT w/Message Light & Recall button Ground Start Key Mounting Bracket Ground Start Key External Alert Message Adjunct lROB Unit Mod. Bulk Pwr. Supply Power Unit Power Panel PEC 31710 3170-OOM 31017 31019 31032 32918 31760 31761 APPARATUS CODE 349A Adapter 7101A01A-003 55A1 77A KS[...]

APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Asynchronous Data Units ATL ADU 62506 D181521 includes 105105506 D8W-87 Cord (14ft) 103786802 Z3A5 ATL ADU 103975349 Mod/RS-232C(M) ADU 2169-001 Z3A1 103963963 Mod/RS-232C (F) ADU 2169-004 Z3A4 103964185 ADU Aux Power 21691 2012D 102600517 248B 102802103 400B2 103848859 D6AP-87 102937[...]

APPENDIX B: Parts Listing DESCRIPTION PEC APPARATUS CODE COMCODE MOH Interface (Reg) 62517 KS-23395 10B ETU 62514 Emergency Trans Unit (2) B25A Cables DE D8W-87 Cord (7ft) Peripherals 62515 248B Adapter Interface for 355AF Adapter Remote Access 400B2 Adapter D6AP-87 Cord D8AM-87 Cord D8W-87 Cord M7U-87 Cord Z3A4 ADU 201 2D Transformer 405193186 103[...]

APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Cross-Connect Hardware Station interface Panel 2750-D28 617A 103982658 Mod/Mod Adapter 2750-D27 Z210A2 106308869 Mod/l 10 Adapter 2750-D29 858A 405177791 Voice/Data (Y) Adapter 2750-T05 WP90851 , L1 405010620 Fanning Strip 2750-D30 50A 105196604 Connector Blocks Block, Connector No PE[...]

APPENDIX B: Parts Listing DESCRIPTlON Cables Octopus Cable (15 ft) Splitter Cable, Tie-Trk Splitter Cable, CO Trk Adapter (TN746) RS-232C X-Over Cable Cable Corm (15’ DE) CPU/MEM interconnect cable Cable, Adapter Cable, Connector Cable, Connector PEC 2720-OSP 2720-05X 2720-06X 2724-30C No PEC No PEC No PEC No PEC No PEC APPARATUS CODE WP90780, L1[...]

APPENDIX C: APPENDIX C: System Additions or Changes Additions and changes can be made to the system to support growth or changing needs of the customer. These system changes include: adding voice or data terminals, changing a voice-only connection to a voice/data connection, adding trunks, adding modems, and adding auxiliary equipment. To handle su[...]

APPENDIX C: System Additions or Changes Table C-A. Unit Loads Port Type I Unit Load ZTN178 port I 0.5 TN742, TN746 1.0 port ETU 2.0 TN760B Port 2.0 TN753B Port 0.5 502-type Headset .75 Adapter 5-Button 1.0 Terminals Port Type Unit Load 10- and 34-Button 1.25 Terminals HFAI Terminals 1.5 MET Terminals 1.0 BIS Terminals 1.5 34-Button Deluxe 2.0 Termi[...]

APPENDIX C: System Additions or Changes 5. Insert the CP into the slot with the latch lever opened. Push it in firmly until you feel resistance and the latch lever moves toward its vertical position, flush with the edge of the CP. Push the lever all the vvay to vertical until the latch pin engages. (See figure C-1.) Add Cabling If the CP added is a[...]

APPENDIX C: System Additions or Changes Figure C-1. Typical System 25 Port Circuit Pack C- 4 November 1995[...]

APPENDIX C: System Additions or Changes Set Option Switches on TN760B CP If the CP being added is a TN760B, use Figure C-2 and Table C-B to choose Figure C-2. Tie Trunk (TN760B) Circuit Pack Option Switches C-5[...]

APPENDIX C: System Additions or Changes Table C-B. TN760B Option Switch Settings and Administration System 25 Installation Situation Circumstance Co-Located Inter-Bldg. . Co-Located Inter-Bldg. Co-Located Inter-Bldg. Co-Located To Sys25 DEFINITY Sys75/75XE Sys85 Sys25 DEFINITY sys75/75xE Sys85 DIMENSION PBX DIMENSION PBX Other Other Net Int. Prefer[...]

APPENDIX C: System Additions or Changes Replace Circuit Pack Replace a CP if it fails or becomes damaged. 1. 2. 3. 4. 5. 6. Make sure that your hands are clean and dry. Put on a wrist grounding strap, and clip it to the grounding block at the back of the cabinet. With your thumb, pull up on the latch pin. When the latch is up, pull down on the latc[...]

APPENDIX C: System Additions or Changes Add Cabinet Add a cabinet if all the slots in the existing cabinets are full and you need to add a CP. Also, if the addition of a CP to a cabinet will cause the unit load to exceed 80, a cabinet must be added. The system can support a maximum of three cabinets. Perform this task outside normal business interf[...]

APPENDIX C: System Additions or Changes 6. 7. 8. 9. 10. 11. 12. 13. 14. Power down the system —all cabinets (Cabinet 1 last). Connect the cabinets, following the instructions under “Install System Cabinets” in Section 2. Connect a #6 AWG copper wire between the ground block of the new cabinet and the ground block of Cabinet 1. See Note. Make [...]

APPENDIX C: System Additions or Changes Add Terminal 1. 2. 3. 4. 5. 6. Evaluate the cabinet unit power load using the procedures under “Evaluate cabinet unit Power Load” in this appendix. Check for available ports on checking the octopus cables the back of the cabinet. a compatible CP using the SAT or by attached to the 25-pair receptacles on t[...]

APPENDIX C: System Additions or Changes Add Trunk 1. 2. 3. 4. 5. 6. If you are adding a DID or tie trunk, evaluate the cabinet unit power load using the procedures under Evaluate Cabinet Unit Power Load in this appendix. Check to see that the trunk has been connected to an RJ21X (for a DID trunk) or RJ2GX (for a tie trunk) network interface by the [...]

Figure C-3. DS1 Network Interface Connections Replace Voice-Only Terminal With Terminal 1. 2. 3. 4. 5. 6. 7. 8. Using the Voice and Data Station Records Voice/Data Form (see “INSTALL EQUIPMENT ROOM STATION CABLING” in section 2), find the jack in the SIP adapter associated with the voice terminal that is to share a cable with. a data terminal o[...]

APPENDIX C: System Additions or Changes 9. When the terminal is initialized, test it following the appropriate procedures in Section 3, “System Tests. ” Add Pooled Modem Circuit Pack 1. 2. 3. 4. Select a cabinet in which to add the TN758 Pooled Modem CP. Only two Pooled Modem CPs per cabinet are allowed. Add the Pooled Modem CP following the pr[...]

APPENDIX D: APPENDIX D: System Upgrades A D-kit-of-parts (PEC 62526N) k required to upgrade a Release 1 or a Release 2 system to a Release 3 V3 system. The kit contains the following: ● ZTN142 CPU/Memory Circuit Pack(1) ● ZTN131 Service Circuit Pack (1) ● Switched Loop Attendant Console (SLAC) Face Plates (2) ● Cassette Tapes (2) ● Releas[...]

APPENDIX D: System Upgrades 8. 9. 10. 11. 12. 13. 14. Remove the ZTN82 or ZTN128 Call Processor CP from slot 2 and discard (R1 only). Remove ZTN85 Service CP from slot 3 (R1 only) or slot 2 (R2 only) and replace with ZTN131 Service CP. (Put in slot 2.) If ZTN85 is not replaced, move ZTN85 to slot 2. Power up the system-Cabinet 1 last. Cold start th[...]

APPENDIX D: System Upgrades 16. 17. 18. 19. Save the translations, and verify the accuracy of the backup tape. Refer to the Administration Manual for R3V1 (555-540-500) for these procedures. Install the front cover on Cabinet 1. Overlay the existing face plates on each switched loop console with the plates provided in the D-kit. Familiarize the cus[...]

APPENDIX E: APPENDIX E: Administration Codes and Data The tables in this appendix are intended to help those familiar with system administration locate specific information without having to refer to the full text in the Administration Manual. Default values, if applicable, are indicated in bold print in these tables. Default Dial Code Assignments [...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTlON DATA 0 Physical port number CSSPP** 1 Enter terminal type code [See Table E-C] 2 Enter PD. [1 -9999] 3 Restrict dial access to CC) trunk pool [1=Y/0=N] 4 Restrict dial access to all other trunk [1=Y/0=N] pools 5 Assign ringing[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd ) Administering the TN746B with Basic Administration Plug the TN746B into an unadministered carrier/slot location and warm start the System 25 . Note: The TN746B circuit pack is not interchangeable with either the ZTN78 or TN742 circuit p[...]

APPENDIX E: Administration Codes and Data This page is intentionally blank E-2-b[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTlON DATA 17 Send ringing to bridged appearances [1=Y/0=N] when principal doesn’t answer? 18 Send ringing to bridged appearances [1=Y/0=N] when principal is busy? 19 Is this a display station?‡ [1=Y/0=N] 20 Enable autom[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 46 51 52 53 60 90 10 0 10 1 Enable call waiting* [1=Y/0=N] Display the number of any trunks assigned to this station for night service Assign a trunk to this station for night [4-digit trunk number] service Delete[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 101 PERSONAL LINE [3] If type 310 or 311: NOT ADMINISTRABLE 10 2 4-digit "Listed Directory Number” for [trunk #] this trunk 103 Is this the " Principal" statio[...]

APPENDIX E: Table E-B. Administration Codes and Data PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 AUTOMATIC INTERCOM [8 ] 10 2 PDC of paired station [PDC ] 10 3 Button number of the AUTO ICOM [button #] button on the paired station 10 0 Button to be assigned [button #[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 SEND ALL CALLS [11] I f typ e 310 or 311: NO T ADMINISTRABLE 10 2 Enable single-ring reminder? [1=Y/0=N] 10 3 Send ring to bridged stations or to [0-2; 2] coverage statio[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 ALARM [16 ] For types 309, 310, 311 ONLY (read- only ) 10 0 Button to be assigned [button #] 10 1 NIGHT SERVICE [17 ] For types 309, 310, 311 ONLY 10 2 Night Service access code [...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/POC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 101 STAR T [24 ] For types 309, 310, 311 ONLY (read- onlv) 100 Button to be assigned [button #] 10 1 CANCEL [25 ] For types 309, 310, 311 ONLY (read- onlv ) 10 0 Button to be a[...]

APPENDIX E: Table E-B. Administration Codes and Data PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 JOIN [31 ] For type 310 or 311 ONLY (read-only) 10 0 Button to be assigned [button #] 10 1 DESTINATION [32 ] For type 310 or 311 ONLY (read-only) 10 0 Button to be assign[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 BRIDGED ACCESS [37 ] If type 309, 310, or 311: NOT ADMINISTRABLE 102 PDC of Principal station [PDC ] NOTES: Cannot have a BA for a DTAC’s SA. Also, cannot have a BA for your ow[...]

APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 10 1 NEXT [41 ] Note: this feature requires the use of a DISPLAY voice terminal. 10 0 Button to be assigned [button #] 10 1 AGENT STATUS FOR CMS [42 ] 10 2 Assign button subtyp[...]

APPENDIX E: Administration Codes and Data Table E-C. Voice Terminal Type Codes If the Terminal Type is: Code: SINGLE-LINE VOICE TERMINALS: Without message waiting indicator 20 1 With message waiting indicator 20 2 MERLIN CS (ATL) VOICE TERMINALS: 5-Button, Z7302H01 30 2 10-Button Hands-Free Answer on Intercom, Z7309H01 30 3 10-Button Built-in-Speak[...]

APPENDIX E: Administration Codes and Data Table E-D. Feature Button Translation (Menu=1/2) “Action=100” is required before action(s) 101-104 listed in this table are administered. ACTION NOTES BUTTON TYPE ACTION ACTION 101 102 103 1 (1) SYS ACCESS- OR G 2 FACILITY Facility Access Cod e 3 (1, 11, & 15) PERS LINE Trunk Number Owner? 4 EXCLUSI[...]

APPENDIX E: Administration Codes and Data Table E-D. Feature Button Translation (Menu=1/2) (Contd) "Action=100" is required before action(s) 101-104 listed in this table are administered ‘ Refer to page 10-6 of the Administration Manual. November 1995 E-15[...]

APPENDIX E: Administration Codes and Data NOTES: A ? mark indicates that a yes/no If a (No) or (Yes) is present, response. 1) 2) 3) 4) 5) 6) 7) 8) 9) 1 0) 11) 12) 13) 14) 15) If Switched Loop Attendant Switched L OO p Attendant (1/0) response is required. this indicates a strongly suggested Console: NOT ADMINISTRABLE Console cannot be specified as [...]

APPENDIX E: Administration Codes and Data Table E-E. Multiline Voice Terminal Button Defaults 7- SYS ACCESS 12- FLEX DSS 17- FLEX DSS 29- FLEX DSS 8- SYS ACCESS 13- ACCT ENTRY 18- FLEX DSS 30- FLEX DSS 9- REP DIAL 14- SEND ALL CALLS 19- FLEX DSS 31- FLEX DSS 10- REP DIAL 1 5- FLEX DSS 20- FLEX DSS 32- FLEX DSS 11- LAST # DIALED 16- FLEX DSS ! 21- F[...]

APPENDIX E: Administration Codes and Data Table E-F. Switched Loop Attendant Console Button Defaults (Type 310) 7- LOOP† 8- LOOP† 9- LOOP† 10- LOOP† 11- LOOP† 12- ALARM† 17- LOCAL† 29- SCROLL† 13- POS BUSY 18- FLEX DSS 30- FORCED RELEASE† 14- FLEX DSS 19- FLEX DSS 31- LAST # DIALED 15- SOURCE† 20- FLEX DSS 32- FLEX DSS 16- DESTI[...]

APPENDIX E: Administration Codes and Data Table E-G. Switched Loop Attendant Console Button Defaults (Type 311 ) 7- LOOP† 12- ALARM† 17- lNSPECT† 29- SCROLL† 8- LOOP† 13- POS BUSY 18 - LOCAL† 30- FORCED RELEASE† 9- LOOP† 14- FLEX DSS 19- FLEX DSS 31- LAST # DIALED 10- LOOP† 15- SOURCE† 20- FLEX DSS 32- FLEX DSS 11- LOOP† 16- D[...]

APPENDIX E: Administration Codes and Data Table E-H. Direct Trunk Attendant Console Button Defaults (Cold-Start Defaults) 7- SYS ACCESS 8- SYS ACCESS 9- REP DIAL 10- REP DIAL 11- LAST # DIALED 12- FLEX DSS 17- Trunk 0001 29- Trunk 0009 13- ACCT ENTRY 18- Trunk 0002 30- Trunk 0010 14- ATT MSG 19- Trunk 0003 31- Trunk 0011 15- NIGHT 20- Trunk 0004 32[...]

APPENDIX E: Administration Table E-1. Direct Trunk Attendant Console Defaults Installed Defaults) Codes and Data (Administration- 7- SYS ACCESS 12- FLEX DSS 17- 0 29- 0 8- SYS ACCESS 13- ACCT ENTRY 18- 0 30- 0 9- REP DIAL 14- ATT MSG 19- 0 31- 0 10- REP DIAL 15- 0 20- 0 32- 0 11- LAST # DIALED 16- ALARM† 21- 0 33- 0 25- COVER GRP 37-0 †Cannot b[...]

APPENDIX E: Administration Codes and Data Table E-J. MET Set Button Defaults †Cannot be changed. E-22[...]

APPENDIX E: Administration Codes and Data Table E-K. PORT/PDC Administration, Data Terminals (Menu=12) ACTION DESCRIPTlON DATA 0 Physical port number CSSP P 1 Enter data type code [See Table E-K] 2 Enter DD C [1 -9999; 600-704] 3 Restrict dial access to CO trunk pool† [1=Y/0=N] 4 Restrict dial access to all other trunk [1=Y/0=N] pools† 12 DDC o[...]

APPENDIX E: Administration Codes and Data Table E-K. PORT/PDC Administration, Data Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 67 Allow terminal to operate at a baud rate [1=Y/0=N] of 9600 bps† 68 Allow terminal to operate at a baud rate [1=Y/0=N] of 19200 bps† 69 Assign this parity setting to correspond [0-3; 2] with terminal’s pari[...]

APPENDIX E: Administration Codes and Data Table E-L. Data Port Type Codes IF THE DATA PORT TYPE IS CODE: I ( Dat a Lin e Card (DLC) 1801 functionality for ZTN126 or TN72 6 STAR LAN Interface Circuit 1802 Pack (STARLAN CP) in DLC-compatibility mode Disable this individual port (for 0 any of the above data port types) E-25[...]

APPENDIX E: Administration Codes and Data Table E-M. Port Administration, Trunks (Menu=1) ACTION DESCRIPTION DATA 0 Physical port number CSSPP 1 Enter trunk port type code [See Table E-N] 2 Enter trunk number [0001 -9999; 0001-0104] 3 Assign class-of-service code [(DID–1-4; 3) (All other— See Table E-O; 8)] 4 Assign pooled facility access code.[...]

APPENDIX E: Administration Codes and Data Table E-M. PORT Administration, Trunks (Menu=1) (Contd) ACTION DESCRIPTlON DATA 12 For Switched Loop Attendant Systems [0-2; 0=either Att./ ONLY; Which attendant should receive 1=1st At. ONLY/ calls from this trunk?† 2=2nd Att. ONLY] 13 Specify Remote Access usage type‡ [0-2; 0=name, 1=shared, 2-dedicat[...]

APPENDIX E: Administration Codes and Data Table E-N. Trunk Type Codes If the Trunk Type is: Code: Ground Start, CO 701† Ground Start, WATS, FX 702 Ground Start, WPBX/Centrex 705 Loop Start, CO 801† Loop Start, WATS, FX 802 PBX/Centrex 805’ DID Immediate Dial 901 DID Wink Start 902† Auto-in/Auto out 1001 Auto-in/Immediate Dial-out 1002 Immed[...]

APPENDIX E: Administration Codes and Data Table E-O. Trunk Class-of-Service (for all trunks except DID) TRUNK CLASS-OF-SERVICE (FOR ALL TRUNKS EXCEPT DID) CO S NIGHT OUTWARD I N SHORT CODE SERVICE SIGNALING ONLY DISCONNECT 0 TT 1 TT ● 2 TT ● 3 TT ● ● 4 DP 5 D P ● 6 DP ● 7 DP ● ● 8 ● TT 9 ● TT ● 10 ● TT ● 11 ● TT ● ● [...]

APPENDIX E: Administration Codes and Data Table E-P. Port Administration, Auxiliary Equipment (Menu=1) ACTlON DESCRIPTlON DATA 0 Display physical port number, in the form CSSPP 1 Enter special feature port type code (see Table E-Q). 1 Assign external alerts [253] 2 Assign associated station number [PDC of associated station; 0 if night service aler[...]

APPENDIX E: Administration Codes and Data Table E-P. Port Administration, Auxiliary Equipment (Menu-1 ) (Contd) ACTION DESCRIPTlON DATA 1 Assign voice Messaging Service port [260 - 263] type: 260 = standard voice mail services 261 = call coverage/auto-attendant 262 = message drop 263 = bulletin board 2 Assign PD for this VMS port [PD.] 3 Restrict d[...]

APPENDIX E: Administration Codes and Data Table E-Q. Special Feature Port Type Codes This table shows data values associated with Action=1 on Table E-P. Featur e TN742, ZTN7 8 TN763 ZTN7 6 ZTN77 TN748 TN758 ZTN7 9 Tone Detector External Alert 1st Page Zone 2nd Page Zone 3rd Page Zone nth Page Zone DGC Delay Ann. Dial Dictation Music-On-Hold 210 1 2[...]

APPENDIX E: Administration Codes and Data Table E-R. Port Options PORTS, Station/Trunk/Special Port Circuit Board Options FOR QUALIFIED SYSTEMS TECHNICIANS ONLY (See Table E-S, " Applicable Options " ) ACTION DESCRIPTION DATA 32 Set CO disconnect time (in 20 msec [0-2540 msec; 500] increments) 33 Set end-to-end signaling tone timing (in 2[...]

APPENDIX E: Administration Codes and Data Table E-S. Applicable Options See WARNING for Table E-R. Also note that a bullet in a box on this table indicates that the default value for that action (shown in Table E-R) is applicable for this circuit board. No bullet indicates that the option is ● Timing adjustable for internal calls only. † ACTION[...]

APPENDIX E: Administration Table E-T. PDC Administration (Menu=2) Codes and Data ACTION DESCRIPTION DATA 0 Move this station to a new port [CSSPP (new port assignment)] (moved-to port must be vacant) 1 Display terminal type code [See Table E-C] 2-53 All other See note below. 90 Assign/remove PD. Display ID ["11 characters or less,” or ** to [...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) ACTION DESCRIPTlON DATA 3 Assign the number of rings before [Number of rings; 5] unanswered calls extended by Attendant return to the console (1 -31) 4 Force DID calls to unassigned DID [1=Y/0=N] numbers to ring at Attendant Console 5 Force calls to FPDCs that are n[...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTION DATA 37 Specify type of dialing plan for Home [0=7-digit dialing; Area Code calls 1 = 10-digit dialing] 38 Specify the number of digits used for [0=13digits,1=1 5 international dialing digits] 40 Provide call coverage ringing on internal [[...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTlON DATA 75 Change administration password (up to 8 ["8 characters or less”] printable characters, no spaces allowed, display always shows “?????????”) 76 Change display ID for “PDC 0“ (up to 11 [“ATTENDANT’] printable ASCII[...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTION DATA 89 Should this SLAC attendant (specified in [1=Y/0=N ] Action 88) receive a single-ring reminder whenever a new call enters the queue? 90 Dual-position Switched Loop Attendant [0=neither, system: Which attendant should take on 1=1st A[...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTlON DATA 103 For Callback Queuing: Enter the [0-1 20; 30] minimum time (in seconds) between callback retries for outgoing facilities 110 For Remote Access: Enable barrier [1=Y/1=N] codes? 111 Assign DID remote access digits [PD.; 0] 113 Assign[...]

APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTIO N DESCRIPTlON DAT A I 130 Assign RIMS barrier code digits (5 [5 through 15 digits or 0 through 15 digits; 0-9, *, # to remove; 98765] 140 Sync. source” [0= Internal] [CSS of TN767=External 142 Enable automatic sync. Source switching [1=enable/0=disab[...]

APPENDIX E: Administration Codes and Data Table E-W. Standard Call Type Defaults FOR SWITCHED LOOP SYSTEMS ONLY DEFAULT DEFAULT CALL TYPE CODE PRIORITY ATTENDANT (Action 91) (Action 92) (Action 93) Dial Attendant (0) Call Following - Logged to SLAC Non logged in FPDC Unassigned DID Attendant DID access code PD. of Attendant Coverage Returning 1 2 3[...]

APPENDIX E: Administration Codes and Data Table E-X. Message-Center-Like Call-Type Defaults (effect of Action 90) FOR SWITCHED LOOP SYSTEMS ONLY DEFAULT DEFAULT CALL TYPE C0DE PRlORITY ATTENDANT (Action 91) (Action 92) (Action 93) non-logged in FPDC Unassigned DID Coverag e Returning Dial Attendant (0) Attendant DID Access Code Call following – L[...]

Table E-Z. Direct Group Calling (DGC) Administration (Menu=6) ACTION DESCRIPTlON DATA 1 2 3 11 12 13 14 20 21 51 52 53 Assign a DGC access code (0 to delete an existing DGC access code) For data DGC groups only; Disable DGC queuing? Designate the VMS Message Waiting indication receiver List members of a DGC group Add a member to a DGC group Delete [...]

APPENDIX E: Administration Codes and Data Table E-AB. DGC Announcement Administration ACTION DESCRIPTION DATA 1 DGC Announcement 25 5 2 PD C [Unique PDC] 3 Dial Restricted [1=yes, 0=no (default)] 90 Assign Announcement Port Display ID 11 characters or less E-45[...]

APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) ACTION DESCRIPTION DATA 1 Search for PDCs of call coverage [1] sender s 2 Call coverage receiver group [1-32 or 101-132 if DGC coverag e group] 1 Search for stations covering a specified [2 ] grou p 2 Call coverage group [1 -32] 1 Search for PDC of call coverage [[...]

APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 Search for PDC of pickup grou p [9 ] member s 2 Pickup group number [1-16] 1 Search for assigned PDCs [11 ] 1 Search for stations associated with [12 ] directed night service 2 Trunk number for directed night service [trunk number[...]

APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 Search for button location on a station [20 ] 2 PDC of station with buttons [PDC ] 3 Button function code (see II Action [1-42 ] 10111 column of Table E-D) 1 Search for Area Codes assigned to [21 ] specified ARS pattern 2 Pattern [...]

APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 “Given number, get Display ID” search [40 ] (PDC, DDC, FPDC, or DGC access ,code ONLY) 2 Enter existing PDC, DDC, FPDC, or [PDC / DDC / DGC access code: FPDC / DGC] 1 “Given number, get Display ID" search [41 ] (trunk L[...]

APPENDIX E: Administration Codes and Data Table E-AD. Board Type—Wildcard Representation CATEGORY: BOARD DESCRIPTION: DATA: Empty Empty Slot (Searches 15 & 17 only) 0 Station Single-line Voice Terminal or Special Port 2 . . MERLIN CS Voice Terminal or Attendant 3. . MET Voice Terminal 4 ● ✎ Trunk Ground Start or Paging 7 . . Loop Start or[...]

APPENDIX E: Administration Codes and Data Table E-AE. Port/Board Type—Specific Representation CATEGORY: DESCRIPTION: DATA: Voice Station SINGLE-LINE VOICE TERMINALS: Without message waiting indicator 20 1 With message waiting indicator 20 2 MERLIN CS (ATL) VOICE TERMINALS: 5-Button, Z7302H01 30 2 10-Button, Z7303H01 30 4 10-Button Hands-Free Answ[...]

APPENDIX E: Administration Codes and Data Table E-AE. Pod/Board Type—Specific Representation (Contd) CATEGORY: DESCRIPTION: DATA: Voice Station (Contd) ATTENDANT VOICE TERMINALS: Direct Trunk Attendant Console (34-Button Deluxe o r 34-Button Deluxe Built-in-Speakerphone) 30 9 Switched Loop Attendant Console (34-Button Built-in-Speakerphone with 1[...]

APPENDIX E: Administration Codes and Data Table E-AE. Port/Board Type—Specific Representation (Contd) CATEGORY: DESCRIPTION: DATA: Trunk (Contd) Delay Dial-in/Auto-out 100 7 Delay Dial-in/Delay Dial-out 100 8 Special Service Circuit ZTN85 (R1V1, R2V2) 110 1 Service Circuit Pack ZTN131 (R3) 1102 External Alerts 25 3 First Paging Zone 1301 Second P[...]

APPENDIX E: Table For Action=1, Administration Codes and Data E-K Save/Restore and System Restarts (Menu=9) you need to press the PLAY and RECORD buttons. For Action=2 and Action=3, you need to press the PLAY button. ACTION DESCRIPTION DATA 1 Save (Backup) translations [1 to run] 2 Verify translations [1 to run] 3 Restore translations [1 to run] 10[...]

APPENDIX E: Administration Codes and Data Table E-AG. RS232 Port Administration (Menu=10) In response to "RS232=", enter the RS232 connector (1-5*) to be administered. ACTION DESCRIPTION DATA 1 Reassign RS232 connector capability [0 to disconnect port or see footnote † for options and defaults] 2 For Ports 1-4 ONLY*: Change the [0-2;0] [...]

APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=1) ACTION DESCRIPTION DATA 10 0 Assign a pattern number [1-8 ] 10 1 Assign a start time for subpattern 1 A in [HHMM] the form HOUR, MINUTES (HHMM) 10 2 Assign a stop time for subpattern 1A [HHMM] 11 0 Assign Route 1 for subpattern 1A (a [FAC or VFC][...]

APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd ) ACTION DESCRIPTION DATA 23 0 Assign Route 3 for subpattern 1 B (a [FAC or VFC] facility access code [FAC] or virtual facility code [VFC]) 23 1 Assign facility restriction level (FRL 0-3) [FRL] for subpattern 1 B, route 3 24 0 Allow subp[...]

APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd ) ACTION DESCRIPTlON DATA 60 1 Assign a 7-digit emergency telephone [7-digit number] numbe r 60 2 Assign a 7-digit emergency telephone [7-digit number] number 60 3 Assign a 7-digit emergency telephone [7-digit number] numbe r 70 0 Enter f[...]

APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd) ACTION DESCRIPTlON DATA 900 N11 CO exchange for which a pattern [N11 code] is being assigned (where N=2-8) 901 ARS pattern number to route these [1-8 or O if this N11 calls N11 Code must be followed by 4 other digits (N11 -XXXX)] E-59[...]

APPENDIX F: Administration Error Messages APPENDIX F shows Basic Administration error codes and descriptions. The Advanced Administration system uses different terminology. For additional details about an error message in Basic Administration, press the “?” key. The following table lists and describes error messages that can be displayed at the[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1006 : incorrect entry Cabinet-Slot-Port (CSSPP) PP must port-on-board number out be a number from 1 to 8 (varies on of range different circuit packs) 1007 : incorrect action number Must administer ACTION = 1 before can ‘t exceed 1 with proceeding. unequippe[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTlON POSSIBLE SOLUTION 1017 : inappropriate request Cap already installed system already has Direct CA P ACTION = 1 (Cap) Go to MENU 8 (Searches) ACTION = 1 DATA = 18 ACTION = 2 DATA = 309 or 310 ACTION = 3 DATA = 0 1018 : inappropriate request Must remove secondary CAP before must [...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTlON 1031 : at installed max At system maximum of 12 touch- -12 Touch-Tone tone receivers. Receiver s 1032 : at installed max At system maximum of 8 external -8 external alert alert s 1033 : at installed max At system maximum of 3 paging -3 paging zones zones . 103[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1044: inappropriate request Neither primary nor secondary CAP primary or secondary CAP universal port number agrees with the unavailable one stored by admin. on the stack. 1045 : at installed max At system maximum of 104 data -104 data port ports . 1046: incor[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1056 : inappropriate request Trying to administer something other must be virtual facility than a Virtual digit. [0-9, *, #] Must be a Virtual Facility. 1057 : at installed max Group or button maximum reached. System btn or station Station is sender in group. [...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION 1069 : incorrect facility type incompatible with board typ e 1070 : facility type out of range must be 3-4 digits POSSIBLE SOLUTION Board and features do not mix. Check slot location for correct board or not compatible with the already entered types on the board. Must be 3 or 4[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1083 : inappropriate request Recheck translations to see if TT TT generator not installed generator was installed. 1084: inappropriate request Trying to administer a third CAP system already has two when you are only allowed two. CAPS 1085 : incorrect entry Da[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1094: inappropriate request Display attendant position only DISPLAY of SLC- DTAC/SLAC. See: CAP status allowed MENU = 1 (Port) ACTION = 60 for more information. 1095 : action number Check MENU 4 (System out of sequence Administration) for administering must en[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2003 : incorrect button number Check button range for station type. out of range for ATL set 2004 : inappropriate request Cannot administer button features EMT can’t have button on an EMT station or not allowed for particular type of service. 2007: incorrect[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2026 : incorrect entry Check to see if trunk is trunk does not exist administered. No such trunk ID. 2027 : inappropriate request Cannot assign night service to a not optioned for night DID trunk. Trunk not optioned for service night service. 2029 : inappropri[...]

APPENDIX F: Administration Error Messages ERROR MESSAG E AND DESCRIPTION POSSIBLE SOLUTION 2039 : inappropriate request Cannot assign buttons that are buttons fixed- can’t already fixed on the CAP. assig n 2040 : incorrect PDC Has to be an ATL station to assign must be station for prime prime line preference. line pref 2041 : inappropriate reques[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2053 : incorrect entry Area Code = NPA incorrect area code office where N=2-9, P=0-l ,and A=l -9. cod e Office Code = NXX where N=2-9, X=0- 9 Invalid area code or office code for Toll Calls Allowed. 2054 : incorrect entry Data entry must be 0-2. data must be 0[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2074: inappropriate request Check Home Area Code/Toll Call office code exists-list 1 Allowed list to see if office code exists in list 1. Added office code to pattern already . 2075 : inappropriate request Check Home Area Code/Toll Call office code exists-list[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2082 : inappropriate request See: MENU = 7 (TCA) superset exists-list 1 ACTION = 2 Trying to add a number to a TCA list that already exists in another list. In this case, the superset is used in conjunction with wild card characters . 2083 : inappropriate requ[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 208 9 entry out of range ARS Facility Level = O-3. facility restriction level exceeded 2090 : inappropriate request Single line stations are defaulted station not allowed speed personal speed dialing. ATL numbe r stations must be administered personal speed di[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE I AND DESCRIPTION POSSIBLE SOLUTION 3015 : at installed max Can install 16 trunk group -pool groups maximum . 3016 : entry out of range Only 1 digit can be entered for the access code must be 1 trunk pool dial access information. digi t 3017 : entry out of range The maximum value that can be a[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 4001 : entry out of range Maximum FPDCs = 300 FPDC max reached 4002 : incorrect entry Specified FPDC not found. does not exist or used improperly 4003 : action number out of Must do action 1 before removing sequence FPDC . do action 1 display before FPDC remov[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 5013 : incorrect entry Da y = HHMM where HH=00-23 incorrect hours data 5014 : incorrect entry Day = HHMM where MM= 00-59 incorrect minutes data 6000 : incorrect entry Check search type in admin. manual search type does not to see if it exists. exis t 6001 : in[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 6016 : incorrect facility type The subtype number is the entered subfacility type out of type is too large for the facility rang e specified. 6017 : incorrect entry Traffic register number given is out number out of range of range . 6018 : incorrect action num[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7005 : incorrect entry Entered data not valid for restricting incorrect data to restrict PBX calls. PBX call s 7006 : incorrect entry Number of seconds before a data can’t exceed 120 camped on call returns to the attendant console [1-1 20]. 7007 : inappropri[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7023 : incorrect entr y Data value cannot exceed 1. data can’t exceed 1 7026 : incorrect PDC Must be station or data port. must be station or data port 7027 : incorrect entry Entry cannot be 0 or exceed 5 can’t be 0 or exceed 5 digits. digits 7030 : incorr[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7037 : inappropriate request Direct Group Calling Delay announcement group Announcement (1 per system). already exists (Need a ZTN78 or TN742 CP port) Go to MENU = 8 Search ACTION = 1 DATA = 16 ACTION = 2 DATA = 255 ACTION = 3 DATA = 0 (hit c to continue) Dire[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7047 : incorrect PD C Can verify that the PDC is not in a not in any DGC group DGC group by : Go to MENU = 8 Search ACTION = 1 DATA = 6 ACTION = 2 DATA = PDC (hit c to continue) 7048 : incorrect PD C Do a Search to find the DGC group not in this DGC group the [...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7054 : out of space System speed digit pool is full. no more room in digit poo l 7200 : entry out of range Invalid TARGET value specification. RS232 value out of range Target value should be 1-4. See: MENU = 10 (RS232) 7202 : inappropriate request ACTION = 0 u[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7401 : incorrec t MENU = 10 (RS-232) TARGET = 1 entr y ACTION = 1 DATA = 1 or 4 data must be 2 or 3 (Reassign RS232 connector) NOTE: Above statement is wrong. data must be 1 or 4 only 8000 : incorrect action number A blank space is not acceptable. can’t cont[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8111: incorrect entry trunk pool does not exist Check the original trunk pool entered against the ARS trunk pool you are trying administer . 8112: action number out of rang e number must be 0-1 Only 1 and 0 are valid entries for DDD overflow in ARS. 8113: inap[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8402 : entry out of range The list number range is between list reference can’t 1-4 . exceed 4 8403 : entry out of range The pattern range is 1-8 or 0 for must be 0-8 for removal removal. 8404 : incorrect entry The list cannot exceed 4. list reference can’[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8418 : entry out of range MENU = 11 (ARS) ACTlON = 501 list member must be 1 DATA = 1 digit value, 1-8 range. digit; value 1-8 8419 : inappropriate request All members of the list have already all members of list were been displayed. displayed 8420 : incorrect[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8429 : inappropriate request The telephone number cannot be phone number exists-list removed because it’s installed in list 3 3 . 8430 : inappropriate request The telephone number cannot be phone number exists-list removed because it’s installed in list 4 [...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8700 : action number out of Must enter pattern number first. sequenc e must enter pattern number first 8701: incorrect action number Go back and verify the action item does not exist or used taken . improperly 8702: incorrect entry Pattern number for other are[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 9003: inappropriate request MENU = 1 (Port) under Special station to be linked not Feature port. installed ACTION = 1 DATA = 253 ACTION = 2 DATA = PDC or 0 In this case, the PDC is invalid or does not exist. 9004 : inappropriate request Trying to administer an[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION I 9025 : inappropriate request Removal of a station is disallowed if sole member of queued for the station happens to be the only DGC group member of a DGC group that is being queued for. 9026 : inappropriate request Removal of a trunk port is disallowed sole [...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 9035 : inappropriate request All Agent buttons that are in the same Agent buttons must be on linked-list must be on the same same station station . 9036 : inappropriate request Not allowed to administer more than can’t have identical list one Agent button of[...]

APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 904 7 Incorrect entry. Must be CSS or 0. 9048 Cannot change board type Untranslated or (and) remove board via the HI D CKT menu. first . 904 9 Invalid TN or ZTN code for Use correct code to set board options the HI D CKT menu. for board type. 9050 At installed[...]

GLOSSARY GLOSSARY The following is a list of definitions of terms used in System 25 documentation. Administe r To access and change the parameters associated with the services or features of the system. Analog Data Endpoint Data endpoints connected to the system by (built-in or stand-alone) modems. They do not require the use of data modules (Async[...]

Attendant The operator of the attendant console. Attendant Console ● Direct Trunk Console: An electronic call-handling position with pushbutton control. Used by attendants to answer and place calls and to manage and monitor some system operations. ● Direct Extension Selector (DXS) Console: Provides the attendant with a visual indication of the [...]

GLOSSARY Buffe r A circuit or component that isolates one electrical circuit from another. Typically, a buffer holds data from one circuit or process until another circuit or process is ready to accept the data. Bu s A multiconductor electrical path used to transfer information over a common connection from any of several sources to any of several [...]

GLOSSARY Central Office Codes The first three digits of a 7-digit public network telephone number. These codes are numbered from 200 through 999 and are sometimes referred to as NNXS. Central Office Trunk A telecommunications channel that provides access from the system to the public network through the local central office (CO). Channe l A communi[...]

GLOSSARY Covering User The person at an alternate answering position who answers a redirected call. Data Channel A communications path between two points used to transmit digital signals. Data Communications Equipment (DCE) Refers to a specific RS-232C interface connector configuration. The DCE devices are designed to interface directly (pin-for-pi[...]

GLOSSARY Delay-Dial Tie Trunk Digital Digital After a request for service (called a seizure) is detected on an incoming trunk, the system sends a momentary signal followed by a steady tone over the trunk. This informs the calling party that dialing can start. This type of trunk allows dialing directly into the system; that is, the digits are receiv[...]

GLOSSARY Dual-Tone Multifrequency (DTMF) Industry terminology for touch-tone calling. Emergency Transfer Unit (ETU) Provides direct connection of designated Power Failure Transfer (PFT) registered voice terminals to the CO during a power failure or other service interruption. Erlan g A traffic measuring unit that expresses the load of one or more t[...]

GLOSSARY Facility By technical type these include loop-start, ground-start, DID, data, and automatic ringdown trunks. These facilities may be accessed by their facility access codes (FACS). Restriction Level (FRL) A restriction parameter associated with the Automatic Route Selection (ARS) feature. Determines whether a particular station can access [...]

GLOSSARY Ground-Start Trunk On outgoing calls, System 25 transmits a request for service to the distant switching system by grounding the trunk ring lead. When the distant system is ready to receive the digits of the called number, that system grounds the trunk tip lead. When System 25 detects this ground, it removes the ground from the ring lead a[...]

Loop-Start Trunk Modem Modem Simplest type of central office (CO) trunk. Calls are originated by providing a dc path between the tip and ring leads. The CO detects the loop current thus drawn and returns dial tone. Incoming calls are signaled by the CO placing an ac ringing voltage between the tip and ring leads. (The port circuit pack detects this[...]

GLOSSARY Number Plan Area (NPA) The area code. Off-Premises Station (OPS) An arrangement provided by the local telephone company permitting remote terminal equipment to operate as though it were directly connected to the system. This tariffed service can be provided only for FCC-registered single-line voice terminals. Out-of-Building Station Termin[...]

GLOSSARY ● Floating— Assigned to visitors who will be moving about the premises. Floating PDCs may be associated with the attendant position or may be “logged in” by the user at any voice terminal. Calls to the floating PDC will ring at the terminal where “logged in. ” Pickup Group A group of individuals who can answer any incoming call[...]

Protocol A set of conventions or rules governing the format and timing of message exchanges to errors . Public Network The network that can be or long-distance calling. Queu e control data movement and correction of openly accessed by all customers for local An ordered sequence of tasks to be processed. Queuin g . The process of holding calls in or[...]

GLOSSARY Reorder Ton e Atone repeated 120 times a minute; indicates that at least one of the facilities, such as a trunk or a digit transmitter, required for the call is not available. Also called Fast Busy Tone. Single-Line Voice Terminals Single-line voice terminals served by a Tip Ring Line or Analog Line circuit pack (2500 series and 7101 A voi[...]

GLOSSARY Switch The software-controlled communications processor complex that interprets dialing pulses/tones/keyboard characters and makes the proper interconnections both within the system and outside the system. The switch itself consists of a digital computer, software, storage device (memory), and associated circuit packs hardware necessary to[...]

GLOSSARY Terminal Equipment Equipment used to change information (sound, keystrokes) into an electrical signal compatible with System 25’s port circuits. (Voice and data terminals are the two primary types.) Tie Trunk A telecommunications channel that directly connects two private switching systems. Time-Division Multiplex Bus A special bus that [...]

GLOSSARY Trunk Group Telecommunications channels assigned as a group for certain Trunk Port The hardware (circuit pack) providing an interface between the system and central office (CO)/network trunks. Unit Load A measurement used to evaluate a System 25 cabinet’s power load capacity. Each System 25 cabinet can handle 80 unit loads of 48- volt po[...]

INDEX INDEX 617A Panels 2-6 617A Panels Install 2-44 7300H Series Terminals 2-73 Voice Terminal Tests 3-3 7300H Series Voice Terminal Tests 3-3 A Abbreviations 6-1 Acronyms 6-1 Adapters Description 2-8 Install 2-47 RS-232C B-9 Add Auxiliary Equipment C-13 Cabinet C-8 DS1 Trunk C-11 Pooled Modem C-13 Terminals C-10 Trunk C-11 Add Cabling C-3 Add Cir[...]

INDEX Cables B-10 C-Type Connector 2-12 Description 2-11 octopus 2-72 Splitter 2-11 Cabling Add C-3 Call Coverage Test 3-8 Call Management System—installation Guide 5 4 Call Management System—Planning Guide 5-4 Call Management System—Startup Guide 5-4 Carrier Loading Label 2-67 Changes System C-1 Check Performance of Cabinet Components 2-39 C[...]

INDEX DTU (Continued) Operation 4-14 DTU Troubles 4-81 E Emergency Transfer 2-77, 4-4 Install 2-77 Test 3-15 Unit Trouble 4-80 Equipment Auxiliary B-7 Peripheral B-4 Test 4-2 Equipment Room 2-16 Station Cabling 2-60 Trunk Cabling 249 Error 4-32 Error Log 4-27 Access 4-30 Errors 4-4 ETU Trouble 4-80 Evaluate Cabinet Unit Power Load C-1 External Aler[...]

INDEX Install (Continued) SIP 2-4 4 SMDR 2-111 TAE 2-44 Terminals 2-87 Install STARLAN NETWORK Interface 2-112 Installation 2-1 system 2-1 Installation and Maintenance Manual 5-2 Integrated Solution User Guide 5-3 Introduction to AT&T System 25 5-2 L Labels Cable 2-13 Description 2-13 Voice Terminals 2-88 LEDs 4-4 Lightning Protection 2-19 Log [...]

INDEX Panels (Continued) 617A 2-6 Parts B-1 ADUs B-7 Auxiliary Equipment B-7 Cabinets B-1 Cables B-10 Circuit Packs B-3 Connector Blocks B-9 Cords B-10 Cross-Connect Hardware B-9 Peripheral Equipment B-4 RS-232C Adapters B-9 Software B-6 STARLAN NETWORK Equipment B-6 Surge Suppressor B-2 Telephones B-4 Upgrade Kit (R1 or R2 to R3) B-2 Voice Termina[...]

INDEX S SAT 4-6 Connection 2-102, 2-104, 2-706, 2-109 Install 2-102 SAT Troubles 4-81 Selector Console Test 3-9 Service Telephone Number 4-9 Single-Line Voice Terminal Tests 3-5 Single-Line Sets 2-74 SIP 2-6 Adapters 2-8 Cables 2-11 Connections, 7300H Series Terminals 2-73 Connections, Computers 2-75 Connections, CPU/Memory 2-71 Housekeeping 2-76 I[...]

INDEX Terminal (Continued) System Administration 4-6 Terminal Operations Manual 5-3 Terminals Add C-10 Install 2-87 Voice B-4 Test Equipment 2-2 Test Equipment 4-2 Test Points 4-6 Tests 7300H Series Voice Terminal 3-3 ARS 3-6 ATL Cordless Telephone 3-6 Attendant Console 3-9 Call Coverage 3-8 Data Terminal Dialing Feature 3-10 DGC 3-7 Dial Access Co[...]

INDEX U Undiagnosable Troubles 4-102 Upgrade Kit (Rl or R2 to R3) B-2 Upgrade Kit (Rl to R2 to R3] Parts B-2 Upgrades System D-1 User Guides (700 Series) V Voice Terminal Labels 2-88 Tests 3-5 Voice Terminal Troubles Voice Terminals B-4 7300H Series 2-92 Out-of-Building 2-95 Single-Line 2-92 Stand-Alone 2-90 5-3 4-82 Stand-Alone—Remotely Powered [...]