Français dropdown-ico

American Water Heater 40-42K BTU manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation American Water Heater 40-42K BTU. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel American Water Heater 40-42K BTU ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation American Water Heater 40-42K BTU décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation American Water Heater 40-42K BTU devrait contenir:
- informations sur les caractéristiques techniques du dispositif American Water Heater 40-42K BTU
- nom du fabricant et année de fabrication American Water Heater 40-42K BTU
- instructions d'utilisation, de réglage et d’entretien de l'équipement American Water Heater 40-42K BTU
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage American Water Heater 40-42K BTU ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles American Water Heater 40-42K BTU et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service American Water Heater en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées American Water Heater 40-42K BTU, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif American Water Heater 40-42K BTU, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation American Water Heater 40-42K BTU. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    1 Power Direct V ent Gas W ater Heater Installation Instructions and Use & Care Guide 6510418 September 2007 Flammable V apor Ignition Resistant Compliant Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do n[...]

  • Page 2

    2 T able Of Contents W ater Heater Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installing Y our Gas Water Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Unpacking the W ater Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Location Requirements . . . . . . . . . .[...]

  • Page 3

    3 INST ALLING YOUR GAS W A TER HEA TER Consumer Information This water heater is design-certified by CSA International as a Category I, direct vented water heater which takes its combustion air from the outside of the structure and exhausts all products of combustion to the outside of the structure. This water heater must be installed according to [...]

  • Page 4

    4 Location Requirements FIRE AND EXPLOSION HAZARD Can result in serious injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Storage of or use of gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance can result in serious injury or d[...]

  • Page 5

    5 • The water heater should be located in an area not subject to freezing temperatures. W ater heaters located in unconditioned spaces (i.e., attics, basements, etc.) may require insulation of the water piping and drain piping to protect against freezing. The drain and controls must be easily accessible for operation and service. Maintain proper [...]

  • Page 6

    6 Gas Requirements Read the data plate to be sure the water heater is made for the type of gas you will be using in your home. This information will be found on the data plate located near the gas control valve/thermostat. If the information does not agree with the type of gas available, do not install or light. Call your dealer . NOTE: An odorant [...]

  • Page 7

    7 V enting This water heater has a direct vent system in which all air for combustion is taken from the outside atmosphere and all combustion products are discharged to the outdoors. This water heater must be properly vented for removal of exhaust gases to the outside atmosphere. Correct installation of the vent pipe system is mandatory for the saf[...]

  • Page 8

    8 V ent Pipe Installation The following guidelines should be followed when installing the air inlet and exhaust outlet piping: • V enting should be as direct as possible with a minimum number of pipe fittings. • V ent diameter must not be reduced unless specifically noted in the installation instructions. • Support all horizontal pipe runs ev[...]

  • Page 9

    9 V ent T ermination Locations The air inlet and exhaust outlet must be installed with the following minimum clearances (see figure 4): • T welve inches above grade or maximum anticipated snow level. • T welve inch minimum clearance on top or four foot clearance below or to the side of door or window that may be open. • Four feet horizontally[...]

  • Page 10

    10 V ertical T ermination The vertical inlet and exhaust outlet require a return bend or two medium or long sweep radius 90° elbows to keep the air inlet and exhaust outlet downward and prevent entry of rain. Do not include these elbows when calculat- ing the maximum allowable vent pipe because they have already been considered in the vent tables.[...]

  • Page 11

    11 W A TER SYSTEM PIPING FIGURE 8 T ypical W ater Piping Installation FIGURE 9 T ypical T empering V alve Installation Tempered Water to fixtures Cold Water Inlet Tempering Valve (set to 120°F or lower) Piping Installation Piping, fittings, and valves should be installed according to the installation drawing (Figure 8). If the indoor installation [...]

  • Page 12

    12 FIGURE 10A T emperature and Pressure Relief V alve Installation T&P V alve and Pipe Insulation (Some Models) 1. Locate the T&P V alve on the water heater . 2. Locate the slit running the length of the insulation. 3 Spread this slit open and slip it over the T&P V alve. See Figure 10B. Apply gentle pressure to the insulation to ensure[...]

  • Page 13

    13 ELECTRICAL CONNECTIONS Before plugging in the water heater , always make sure: • The voltage and frequency correspond to that specified on the water heater wiring diagram. • The electrical outlet has the proper overload fuse or breaker protection. WIRING DIAGRAM The T emperature and Pressure Relief V alve: • Must not be in contact with any[...]

  • Page 14

    14 INST ALLA TION CHECKLIST W ater Heater Location • Centrally located with the water piping system. Located as close to the gas piping and vent pipe system as possible. • Located indoors and in a vertical position. Protected from freezing temperatures. • Proper clearances from combustible surfaces maintained and not installed directly on a c[...]

  • Page 15

    15 OPERA TING YOUR W A TER HEA TER Lighting Instructions Read and understand these directions thoroughly before attempting to operate the water heater . Make sure the tank is completely filled with water before operating the water heater . Check the data plate near the gas control valve/thermostat for the correct gas. Do not use this water heater w[...]

  • Page 16

    16 W ater temperature over 125°F can cause severe burns instantly or death from scalds. Children, disabled and elderly are at highest risk of being scalded. Feel water before bathing or showering. T emperature limiting valves are available. W ARNING L.P .G. (Bottled Propane) Models Lique fi ed petroleum gas is over 50% heavier than air and in the[...]

  • Page 17

    17 Operational Conditions Condensation Moisture from the products of combustion condenses on the tank surface and the outside jacket of the water heater and forms drops of water which may fall onto the burner or other hot surfaces. This will produce a “sizzling” or “frying” noise. This condensation is normal and should not be confused with [...]

  • Page 18

    18 MAINTENANCE OF YOUR W A TER HEA TER Draining and Flushing It is recommended that the tank be drained and flushed every 6 months to remove sediment which may build up during operation. The water heater should be drained if being shut down during freezing temperatures. T o drain the tank, perform the following steps: 1. Turn of f the gas to the wa[...]

  • Page 19

    19 Replacement Parts Replacement parts may be ordered through your plumber or the local distributor . Parts will be shipped at prevailing prices and billed accordingly . When ordering replacement parts, always have the following information ready: 1. model, serial, and product number 2. type of gas 3. item number 4. parts description See “Repair [...]

  • Page 20

    20 Replacing the Manifold Assembly 1. Check the door gasket for damage or embedded debris prior to installation. 2. Inspect the viewport for damage and replace as required. 3. Insert the manifold assembly into the burner compartment making sure that the manifold tab engages the slot inside the combustion chamber . See Figure 18. 4. Inspect the door[...]

  • Page 21

    21 TROUBLESHOOTING LED ST A TUS PROBLEM SOLUTION An open earth ground circuit to the ignition system. 1. Check that the earth ground connection is properly connected. 2. Check that the earth ground conductor on the water heater is properly connected. Wiring error or a high resistance to earth ground. 1. Check for proper connection of line neutral a[...]

  • Page 22

    22 TROUBLESHOOTING cont. PROBLEM CAUSE SOLUTION NO HOT W A TER Blower will not run. A) Blower unplugged. Plug blower back into 1 15 V AC. outlet. B) No power at outlet. Repair service to outlet. C) Thermostat defective. Replace thermostat. D) High limit control circuit open. Replace ECO. E) Blower motor defective. Replace Blower Assembly . F) Press[...]

  • Page 23

    23 REP AIR P ARTS ILLUSTRA TION Item No. Parts Description 1 Blower 2 Pressure Switch (Not Pictured) 3 Flue Baffle 4 Heat T rap (Cold) 5 Heat T rap (Hot) 6 Cold W ater Dip T ube 7 Anode Rod* 8 T emperature and Pressure V alve 9 Drain V alve 10 Gas Control V alve/Thermostat 1 1 Hot Surface Igniter (HSI)** 12 Natural Gas Burner 13 L.P . Gas Burner** [...]

  • Page 24

    24 Listed Parts Kits and Illustrations Item 1 1: Flame Sense/Hot Surface Igniter Assembly . Item 12: Burner (Natural Gas) Item 13: Burner (L.P . Gas) Item 14: Manifold door assembly which contains the manifold tube, gasket, manifold door , two piece wire connector with retainer clip, and flame sense/hot surface igniter assembly . (Natural Gas) Item[...]