APC SYBT3 manuel d'utilisation
- Voir en ligne ou télécharger le manuel d’utilisation
- 64 pages
- 2.95 mb
Aller à la page of
Les manuels d’utilisation similaires
-
Battery Charger
APC SU700RM2U
1 pages 1.42 mb -
Battery Charger
APC RBC6
6 pages 1.56 mb -
Battery Charger
APC RBC28
2 pages 0.02 mb -
Battery Charger
APC RBC24I
2 pages 0.02 mb -
Battery Charger
APC SURT3000 VA 3U
3 pages 0.7 mb -
Battery Charger
APC su0663a
2 pages 0.11 mb -
Battery Charger
APC 500
1 pages 0.13 mb -
Battery Charger
APC 208V
2 pages 0.52 mb
Un bon manuel d’utilisation
Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation APC SYBT3. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel APC SYBT3 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.
Qu'est ce que le manuel d’utilisation?
Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation APC SYBT3 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.
Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.
Donc, ce qui devrait contenir le manuel parfait?
Tout d'abord, le manuel d’utilisation APC SYBT3 devrait contenir:
- informations sur les caractéristiques techniques du dispositif APC SYBT3
- nom du fabricant et année de fabrication APC SYBT3
- instructions d'utilisation, de réglage et d’entretien de l'équipement APC SYBT3
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes
Pourquoi nous ne lisons pas les manuels d’utilisation?
Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage APC SYBT3 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles APC SYBT3 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service APC en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées APC SYBT3, comme c’est le cas pour la version papier.
Pourquoi lire le manuel d’utilisation?
Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif APC SYBT3, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.
Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation APC SYBT3. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.
Table des matières du manuel d’utilisation
-
Page 1
990-7810B, August 2002 APC Symmetra RM 4–12 kV A UPS Installation Manual English[...]
-
Page 2
[...]
-
Page 3
T ABLE OF C ONTENTS Chapter 1: Safety and General Information........................................................ 1 Save These Instructions -------------------------------------------------------------------------------------------------------- --------------1 Conventions Used in this Manual -----------------------------------------------------[...]
-
Page 4
T ABLE OF C ONTENTS Chapter 4: Installation ..................................................................................... 17 Unpacking ---------------------------------------------------------------------------------------------------------------------- ---------------- 17 Inspection ---------------------------------------------------------[...]
-
Page 5
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 1 Save These Instructions This Safety section contains important instructions that must be follo w ed during installation and mainte nance of APC equipment. Conventions Used in this Manual The following symbols are use d throughout this manual. Carefully read all informatio n boxes and abide by the ins[...]
-
Page 6
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 2 Deener gizing Safety The UPS contains internal batteries a nd may present a shock hazard even when disconne cted from the branch circuit (mains). Before installing or serv icing the equipment, ensure that the system enable switch and input circuit breaker are set to stand- by (OFF), that internal bat[...]
-
Page 7
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 3 Battery Replacements Kits and Batter y Recycling See your dealer or visit the APC web site at http://www.apc.com for information on battery replacement kits and battery recycling. If returning used batteries to APC for recycling, ship used batteries in the battery replacement packing material. PowerS[...]
-
Page 8
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 4 Regulatory Agency Approvals Countries North America and 208V Countries LISTED 42C2 E96563 LR63938 Europe and 230V Countries N 394 Japan and 200 V Countries LISTED 42C2 E96563 Declaration of Conformity (Europe and 230 V Countries)[...]
-
Page 9
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 5 Life Support Policy As a general policy, American Pow er Conversion (APC) doe s not recommend the use of any of its products in life support applications w here failure or malfunction of the APC product can be reasonably expected to cause failure of the life support device or to significantl y affect[...]
-
Page 10
C HAPTER 1: S AFETY AND G ENERAL I NFORMA TION 6[...]
-
Page 11
C HAPTER 2: B ASICS 7 About Y our UPS The Symmetra RM is a high-performance, un interruptible power system (UPS) in a “power array” configuration. It is designed to power high availabilit y servers and other sensitive electronic equipment. T he UPS provides conditioned, reliable AC po w er to connected equipment, an d provides protection from p[...]
-
Page 12
C HAPTER 2: B ASICS 8 Table 3: Optional Accessories Model Number Description North America and 208/240V (Ø- Ø -G) Europe and 230V (Ø- N -G) Japan and 200 V (Ø- Ø -G) SYTF2 208 Vac to 120 Vac, 5 kVA step-down transformer with (2) 15-amp circuits and (4) 5-20R T-slots Yes SYTF2J 200 Vac to 100 Vac, 3.5 kVA step-down transformer with (2) 15-amp c[...]
-
Page 13
C HAPTER 2: B ASICS 9 Pr oduct Overview Front View Component Identification Figure 1: UPS – Front View PowerView and Bezels Removed Figure 2: UPS – Front and Side View Power Module(s) : Each module can provide up to 4 kVA/2.8 KW power. The UPS frame can support up to four power modules. Main Intelligenc e Module : The Main Intelligence [...]
-
Page 14
C HAPTER 2: B ASICS 10 Rear View Component Identification Figure 3: UPS- Rear View (SYPD3 installed) Figure 4: UPS- Rear View (SYPD4 installed) System Fan : The system fan provides cooling for frame components. Communications Card : Provides serial interface port for remote management and communicatio ns to extended run battery cabinets. Ac[...]
-
Page 15
C HAPTER 2: B ASICS 11 System Block Diagram MIM RIM COM Card Accessory Cards Po werV iew D isp la y DB9 COM Port Battery Monitor Bus External Battery Power Input Circu it Break er Backfeed Rela y Automatic By pa ss Manual By pass External Battery Frame COM Pow er Module Pow er Module Pow er Module Battery Module 120 VDC AC in 155 to 276 VAC Battery[...]
-
Page 16
C HAPTER 2: B ASICS 12[...]
-
Page 17
C HAPTER 3: S ITE P REP ARA TION 13 Reminder Checklist Purchase of System Have you ... 1. determined your load po w er and runtime requirements? 2. purchased redundant po w er and battery modul e if desired? 3. evaluated and selected a serv ice plan? Refer to http://www.apc.com/products/symmetra_ rm for answers to these and other questions. Site Pr[...]
-
Page 18
C HAPTER 3: S ITE P REP ARA TION 14 Shipping & Receiving The UPS and modular components are shi pped on one or more pallets, depending on t he configuration. The frame is installed first and then modular compo nents are installed within the frame. Weights and Measurements Length Inches (cm) Width Inches (cm) Height Inches (cm) Weight lbs (kg) U[...]
-
Page 19
C HAPTER 3: S ITE P REP ARA TION 15 Installation Requir ements When selecting a location for the UPS, consider the fol lowing: Physical Requirements Standard Installation (4-post rack) • Standard 19 in. (46.5 cm) rack • At least 800 mm deep • 15U rack space • Recommended installation is in the bottom of the rack, due to its weight of up to [...]
-
Page 20
C HAPTER 3: S ITE P REP ARA TION 16 Electrical Requir ements The following provides gui dance for planning the electrical installation. Check loca l and national codes. A qualified electrician may be required. Input Connection Method Maximum Load Voltage (Vac) Current Full Load Connection Hardwired 16 kVA 200, 208, 220, 230, or 240 100 A • Extern[...]
-
Page 21
C HAPTER 4: I NST ALLA TION 17 Unpacking The UPS and accompanying components is packaged in a robust shipping carton. Carefully remove the package contents. The UPS and modular components are ship ped on one or more pallets, depending on the configuration. The packaging is rec y cl able; save it for reuse or dispose of it properly. Inspection Inspe[...]
-
Page 22
C HAPTER 4: I NST ALLA TION 18 1. Remove the bolts securing the shipping brackets to the pallet. 2. Use the metal brackets (contained in the mounting rail kit) to attach the cart to the pallet. Front[...]
-
Page 23
C HAPTER 4: I NST ALLA TION 19 3. Transfer the UPS to the cart. Two people are required to lift, move, or install the UPS due to its weight. • Slide the UPS onto the cart. • Once the UPS is on the cart, pull the cart away from the pallet. • Remove the metal brackets from the cart and pallet. 4. Move the UPS on its cart to the front of the equ[...]
-
Page 24
C HAPTER 4: I NST ALLA TION 20 2. Assemble the rails as shown. 3. Install the rails in the rack. Left side facing front Right side facing front Bottom U-Space[...]
-
Page 25
C HAPTER 4: I NST ALLA TION 21 4. Slide the UPS frame into the rack. Two people are required to lift, move, and install the UPS due to its weight. 5. Secure the UPS frame in the rack.[...]
-
Page 26
C HAPTER 4: I NST ALLA TION 22 Wiring the UPS • Verify that all branch circuit (mains) and lo w voltage (control) circuits are de-energized, and locked out before install ing cables or making connections, whether in the junction box or to the UPS. • Verify that the battery modules are not installed in the UP S. Do not install battery modules un[...]
-
Page 27
C HAPTER 4: I NST ALLA TION 23 3. Remove the input-wiring acce ss panels . 4. Remove the input and output (if appl icable) knockouts . 5. Ensure that the battery jumper is installed betwee n the terminal blocks . The battery jumper is used to disconnect batteries during shipm ent, if the battery modules are shipped i nstalled. 6. Attach[...]
-
Page 28
C HAPTER 4: I NST ALLA TION 24 Option 1: Internally Powered (with Jumper Cable) Option 2: Externally Powered (no Jumper Cable) 12. If required, connect the Remote Emergency Po w er Off (REPO) circuit. Check national and local codes before w iring. The output power can be dis abled in an emergency by closing a switch connected to the REPO. You m[...]
-
Page 29
C HAPTER 4: I NST ALLA TION 25 Completing the Installation 1. Install all power modules. Power modules can be installed in any slot on the left side of the UPS. • Slide the power module into the frame. • Slide the latch up and tight en the captive screw . Two people are required to lift, move, install, or remove battery modules due to i[...]
-
Page 30
C HAPTER 4: I NST ALLA TION 26 Blank cover plates must be installed over slots that do not contain battery or power modules. 3. Install the bezels . 4. Install the PowerView Display . • Connect the cable to the Main Intelligence Module (MIM). • Align the tabs on the sides of the bezel with the slots on the front of the UPS frame and[...]
-
Page 31
C HAPTER 4: I NST ALLA TION 27 Connecting Load Equipment to the UPS 1. Plug all load equipment int o PDU receptacles . 2. Ensure that all PDU circuit breakers are turne d ON. Refer to Table 2 on page 8 for additional information. SYPD3 (200/208/240 V) SYPD4 (220/230/240 V)[...]
-
Page 32
C HAPTER 4: I NST ALLA TION 28 Final Installation Checklist Turn OFF or disconnect the load equi pment. Verify the Input Voltage Selection s witch setting. Ensure that the system is securely mounted in rack. Ensure that all modules (power, batter y , and intelligence) are full y installed. Check that the PowerView is connected t[...]
-
Page 33
C HAPTER 4: I NST ALLA TION 29 Post Installation Pr ocedures This section contains information on ho w to replace battery, po we r, and intelligence mo dules. Replacing Battery Modules Two people are required to lift, move, install, or remove battery modules due to its weight. 1. Loosen the captive screw and slide th e latch down. 2. Slide [...]
-
Page 34
C HAPTER 4: I NST ALLA TION 30 Replacing Intelligence Modules 1. Loosen captive retaining scre w s . 2. While holding retaining l atch, remove the Main Intelligence Module (MIM) or Redundant Intelligence Modu le (RIM) 3. Slide new MIM or RIM module into the frame. 4. Tighten the captive retaining screws .[...]
-
Page 35
C HAPTER 5: S PECIF ICA TIONS 31 T echnical Refer ence This section contains operation, input, outp ut, phy sical, and complianc e specifications for the UPS. Operational Specifications System Power Array with hot-swappable modules that are redundant, scalable, self-diagnosing, and fault-tolera nt Topology On-line, double conversion with input powe[...]
-
Page 36
C HAPTER 5: S PECIF ICA TIONS 32 Output Specifications Nominal Output Voltage 200, 208, 220, 230, 240 Vac; 50 or 60 Hz, 1 phase, 3 wire Output Power kVA 4 – 16 kVA Output Power kW 2.8 – 11.2 kW Load Power Factor 0 – 1 Output Frequency 60 or 50 Hz nominal Output Voltage Regulation Steady State < ± 3% for no load to full load, min ac input [...]
-
Page 37
990-7810B, August 2002 APC Symmetra RM 2–6 and 4–12 kV A UPS Operation Manual English[...]
-
Page 38
[...]
-
Page 39
T ABLE OF C ONTENTS APC Contact Numbers and Support Visit the APC Web site for contact numbers and support at http://www.apc.com/suppor t . Battery Replacements Kits and Battery Recycling See your dealer or visit the APC web site at http://www.apc.com for information on battery replacement kits and battery recycling. If returning used batteries to [...]
-
Page 40
T ABLE OF C ONTENTS[...]
-
Page 41
C HAPTER 1: O VERVIEW 1 PowerView Figure 1: Typical PowerView Display This manual contains information on ho w to operate the UPS using the Po w erView user interface. PowerView provides the ability to contro l, configure, and monitor the UPS. Navigation Eight (8) PowerView menus allo w you to perform functions and commands. Menu Description Contro[...]
-
Page 42
C HAPTER 1: O VERVIEW 2 Functions Figure 2: Display Panel PowerView includes an alphanumeric display, navigation keys, status indicators and an audi ble alarm. The tables belo w descr ibe the status indicators and ho w to navigate bet w e en Po werV ie w menu s. Status Indicator Color Status LOAD ON Green The UPS is supplying pow er to the load. It[...]
-
Page 43
C HAPTER 2: G ETTING S TA R T E D 3 T urning on the UPS Follow the steps below to turn ON the UPS. • The factory default Monitoring screen is sho w n. Your actual screen may vary. • After the PowerView has been inactive for 10 minutes (user settable), the display will revert to the Monitoring screen. Po werV iew RM Rev: A English Pl[...]
-
Page 44
C HAPTER 2: G ETTING S TA R T E D 4 Powering Up the Load Equipment Follow the steps below to turn ON the output of the UPS and po w er the load equipment. >Control Logging Status Display Setup Diags Accessories Help >Turn Load On Do Self Test Simulate Power Fail Graceful Reboot Confirm: Turn UPS ON NO, ABORT > YES, Turn[...]
-
Page 45
C HAPTER 2: G ETTING S TA R T E D 5 Powering Down the Load Equipment Follow the steps below to turn OFF the output of the UPS an d power down the load equipment. >Control Logging Status Display Setup Diags Accessories Help >Turn Load Off Do Self Test Simulate Power Fail Graceful Reboot Confirm: Turn UPS OFF NO, ABORT > [...]
-
Page 46
C HAPTER 2: G ETTING S TA R T E D 6 Bypass Operation In addition to the automatic bypass, a maintena nce bypass switch is provided with the UPS. Placing this switch in bypass mode connects the load equipme nt to the branch circuit, even if the UPS is turned OFF. When using the maintenance bypass, the input circuit breaker must be ON, or power will [...]
-
Page 47
C HAPTER 2: G ETTING S TA R T E D 7 Language Setting The factory default language of the user interface is Engl ish. You can change the language by do w nloading ne w firmware into the PowerView. French, German, Italian, and Spanis h are available on the enclosed CD. Visit the APC web site at http://www .apc.com for multilingual product doc umentat[...]
-
Page 48
C HAPTER 2: G ETTING S TA R T E D 8 Figure 4: Typical Programming Cable 3. Connect the programming cable (i ncluded, APC part number 940-0082) bet ween the PowerView and the UPS cable. • Attach the RJ-45 connector to the port on the rear of the PowerView. • Connect the female DB-9 connector of the programming cable to a serial port on the compu[...]
-
Page 49
C HAPTER 2: G ETTING S TA R T E D 9 Figure 5: Show n connecte d to Symmetra RM 2-6 kV A 6. Start HyperTerminal or another terminal emulation program on the computer. • Set the communication parameters to 8 bits, no parity, no flow control, 1 stop bit, and 19,200 bps. • After establishing a connection, use the Xmodem protocol to transfer the lan[...]
-
Page 50
C HAPTER 2: G ETTING S TA R T E D 10[...]
-
Page 51
C HAPTER 3: M ENU C OMMANDS 11 Command Refer ence The following sections describe the details of each comm and. Commands are organized according to the menu hierarchy in the Po w erView. Accessories Menu The Accessories menu allows y ou to monitor APC accessories if they are installed. Note t hat the PowerView must be connected to the computer inte[...]
-
Page 52
C HAPTER 3: M ENU C OMMANDS 12 Display Menu The Display menu lets the us er customize the PowerView display. Display Function Options Date/Time Sets the correct date and time. dd:mmm:yyyy Password Protects against unauthorized configuration changes. Password Sets a password. Valid characters include: A–Z, or 0–9; type ‘_’ to complete. Timeo[...]
-
Page 53
C HAPTER 3: M ENU C OMMANDS 13 Diagnostics Menu The Diagnostics menu prov ides information for use in troubleshooting. Menu Item Function Fault and Diagnostics Displays current system fault and diagnostic inf ormation of that fault. (Main) Intelligence Module Displays detailed intellige nce module status and information. Redundant Intelligence Modu[...]
-
Page 54
C HAPTER 3: M ENU C OMMANDS 14 Logging Menu (continued) Menu Item Function List Event Groups Lists the specific events in each group. Power Events UPS Control Events User Activities UPS Fault Event s MeasureUPS Events Clear Log Clears the view log. Does not clear the active event lists. Status Menu The Status menu displays information regardin g lo[...]
-
Page 55
C HAPTER 3: M ENU C OMMANDS 15 Setup Menu The Setup menu lets the user customize the UPS functionality. Menu Item Function Options Shutdown Sets the shutdown par ameters in the event of a utility power failure. None Low Batt(ery) Dur(ation) Sets the number of minutes an audible alarm sounds before the UPS shuts down due to battery exhaustion. 2(def[...]
-
Page 56
C HAPTER 3: M ENU C OMMANDS 16 Setup Menu (continued) Menu Item Function Options Alarms Sets the alarm thresholds. None Redundancy An audible a larm sounds if the redundancy falls below this level. 0(default), 1, or 2 Load An audible alarm sounds w hen the load exceeds this limit. (Upper value is limited by the maximum power of the UPS.) Never(defa[...]
-
Page 57
C HAPTER 4: M ESSAGES 17 T r oubleshooting The PowerView reports various messages on the displa y, including alarm status and changes in system configuration. This section lists all the Po werView display messages, what each means, and an appropriate corrective action. Contact APC Technical Support Staff for assistance with complex UPS pr oblems. R[...]
-
Page 58
C HAPTER 4: M ESSAGES 18 PowerView Mess age Meaning Corrective Action AC adequate for UPS but not for bypass. The UPS will funct ion on-line with the input voltage, but in the event that bypass is required, the input voltage is not adequate to power the load equipment. Option 1: Improve the incoming voltage. Option 2: Proceed with startup. Normal b[...]
-
Page 59
C HAPTER 4: M ESSAGES 19 PowerView Mess age Meaning Corrective Action Redundancy Restored. Power module redundancy loss occurred and was restored. Either additional modules have been installed or the load has been reduced. Load is No Longer above Alarm Threshold. The load exceeded the load alarm threshold. The situation has been corrected because e[...]
-
Page 60
C HAPTER 4: M ESSAGES 20 PowerView Mess age Meaning Corre ctive A c tion Redundancy is below alarm threshold. Actual power module redundancy has fallen below the user specified redundancy alarm threshold. Either power module(s) failed or the load has increased. Option 1: If possible, install additional power modules. Option 2: Decrease the load. Op[...]
-
Page 61
C HAPTER 4: M ESSAGES 21 PowerView Mess age Meaning Corrective Action On Battery. The UPS is in the on-battery mode. The battery modules are being discharged. No corrective action is necessary. Note: Runtime i s limited in duration. Prepare to shutdown the UPS and the load equipment, or restore incoming voltage. Need Bat Replacement. One or more ba[...]
-
Page 62
C HAPTER 4: M ESSAGES 22 PowerView Mess age Meaning Corrective Action Input circuit breaker tripped open. The input circuit breaker on the UPS tripped open. Input voltage is disconnected to the UPS. Option 1: If this occurs in conjunction with an overload condition, decrease the load and reset the breaker. Option 2: If no overload condition exists,[...]
-
Page 63
C HAPTER 5: M AINTENANCE 23 Service If the UPS requires service, do not return it to the dealer ! Follow these steps: 1. Review the problems discussed in the Mess ages chapter to eliminate common problems. 2. Verify that no circuit breakers are tripped. A tripped circuit breaker is the m ost common UPS problem! 3. If the problem persists, call cust[...]
-
Page 64
C HAPTER 5: M AINTENANCE 24[...]