Français dropdown-ico

Ariens 920021 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Ariens 920021. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Ariens 920021 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Ariens 920021 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Ariens 920021 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Ariens 920021
- nom du fabricant et année de fabrication Ariens 920021
- instructions d'utilisation, de réglage et d’entretien de l'équipement Ariens 920021
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Ariens 920021 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Ariens 920021 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Ariens en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Ariens 920021, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Ariens 920021, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Ariens 920021. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Owner/Operator Manual Manuel Du Propriétaire/Utilisateur 920 Series Sno-Thro ® 04335600I 1/13 Printed in USA Models 920013 – Comp act 22 LE (SN 075000 +) 920014 – Comp act 24 LE (SN 075000 +) 920020 – Compact 24 LET (SN 000101 +) 920021 – Comp act 24 LE (SN 000101 +) E10 The use of an y gasoline exceeding 10% ethanol (E10) or 10% MTBE wil[...]

  • Page 2

    EN - 2 SAFET Y . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASS EM BL Y . . . . . . . . . . . . . . . . . . . . . . . 8 CONTROLS and FEA TURES . . . . . . . . 14 OPERA TION . . . . . . . . . . . . . . . . . . . . . 17 MAINTENANCE . . . . . . . . . . . . . . . . . . 23 SERVICE AND ADJUSTMENTS . . . . . 28 STORAGE . . . . . . . . . . . . . .[...]

  • Page 3

    EN - 3 • Record Unit M odel and Serial numbers he re. • Record Engine Model and Serial numbers he re. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchas e. Registering the product will help the comp any process warranty claims or contact you with the latest service information. All c laims meeting requireme[...]

  • Page 4

    EN - 4 SAFETY ALERT S Look for these symbols to point out important safety precautions. They mean: Attention! Personal Safe ty Is Involved! Become Alert! Obey The Message! The safety alert symbols above an d signal words below are used on decals and in this manual. Read and understand all safet y messages. NOTATIONS NOTICE: General reference inform[...]

  • Page 5

    EN - 5 1. DANGER! Danger! ONL Y use clean-out tool to clear blockages. NE VER use your hand s. Never d irect discharge towards pers ons or property that may be injured or damaged by thrown objects. Keep people away from unit while operating. Keep children out of wor k area and under watchful care of a responsible adult. S top engine, remove key , r[...]

  • Page 6

    EN - 6 EMISSION CONTROL SYS TEM This equipment and/or its engine may include exhaust and evaporat ive emissions control system components required to meet U.S. Environmental Protection Agenc y (EP A) and/or California Air Resources Board (CARB) regulations. T am pering with emission controls and components by unauthorized personnel may result in se[...]

  • Page 7

    EN - 7 DO NOT overload th e machine cap acity by attempting to operate or to clear snow at too fast a rate. Slow down and tur n corners slowly . Do not opera te in reverse unl ess absolutely necessary . AL WA YS back up slowly . Always look down and behind before a nd while backing. Disengage att achment dri ve when traveling from one wo rk area to[...]

  • Page 8

    EN - 8 PACKAGE C ONTENT S ASSEMBL Y W ARNING: A VOID INJURY . Read and understand the entire Safety section before proceed ing. W ARNING: Dropping or tipping over boxed unit could result in personal injury or damage to unit. PACKAGE CONTENTS Check the contents of your packag e for the parts listed below (Figure 3): Item Part No. Qty Description 1. [...]

  • Page 9

    EN - 9 ASSEMBLY T ools Req uired: • Pliers • Open-End Wrenches: 3/8", 7/16", 1/ 2", 9/16" and/or Adjust able Wrench •T i r e G a u g e • T orque Wrench (Optional) Unfold Lower Hand lebar (Figure 4) 1. Remove wheel pins from eac h side of the unit and slide wheels away from frame (Figure 4). Do not remove wheels completel[...]

  • Page 10

    EN - 10 Unfold Upper Handleb ar Assembly (Figure 7) 1. Rotate the handlebar int o operating position. NOTICE: Be careful not to damage cable spring hooks when rotating handlebar upward. . 2. Install the remaining handlebar hardware attaching the upper handlebar assembly to t he lower handlebar (Figure 5). 3. Tighten all hardware. 4. Remove packagin[...]

  • Page 11

    EN - 11 INST ALL DISCHAR GE CHUTE AND DISCHARGE CHU TE CRANK (Figures 10 and 1 1) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge c hute over opening in the auger housing. Finger tighten the mounting hardware removed in step 2. NOTICE: Leave discharge chute p[...]

  • Page 12

    EN - 12 Inst all Remote Deflector Cable (920014, 020, 021) (Figures 12 and 13) 1. Pull rubber seal cap away from snap fitting (Figure 12). . 2. Install snap fitting into cable bracket ’ s mounting hole located und er the control panel. 3. Position rubber seal cap over the top of snap fitting. 4. Move deflector cont rol lever to rear most position[...]

  • Page 13

    EN - 13 8. Install cable into clip on top of discharge chute pedestal (Figure 13). . 9. Make sure deflector cable loops above gear cover between cable clip and c able support bracket (Figure 13). 10. T est controls to be sure deflector works properly . NOTICE: If deflector does not follow f ull range of travel see Remote Discharge Deflector Control[...]

  • Page 14

    EN - 14 1. Attachment Clutch Le ver 2. Speed Selector 3. Traction Drive Clutch Lever 4. Discharge Chute Crank 5. Muffler Guard 6. Remot e Discharge Chute Deflector (920014, 021) 7. Discharge Chute 8. Impeller 9. Auger 10. Scraper Blade 1 1. A uger Gearcase 12. Clean-out T ool 13. Skid Shoe(s) 14. Axle Lock P in 15. Belt Cov er 16. Handlebar 17. Hea[...]

  • Page 15

    EN - 15 1. Attachment Clutch Le ver 2. Speed Selector 3. Traction Drive Clutch Lever 4. Discharge Chute Crank 5. Muffler Guard 6. Remot e Discharge Chute Deflector 7. Discharge Chute 8. Impeller 9. Auger 10. Scraper Blade 1 1. Auger Gearc ase 12. Clean-out T ool 13. Skid Shoe(s) 14. Belt Cov er 15. Handlebar 16. Headlight 17. Remote Deflector Contr[...]

  • Page 16

    EN - 16 1. Gas T ank an d Cap 2. Oil Fill and Dipstick 3. Fuel Shut-off V alve 4. Recoil Starter Handle 5. Elect ric S tarter 6. Throttle (920014, 020 ) 7. Choke 8. Ignition Switch 9. Primer B ulb 10. Oil Drain P lug 1 1. E ngine Shut Off Switch (920013, 021) Figure 16 2 1 4 9 1 3 8 6 920014, 020 – Brig gs & S tratton 4 920013, 02 1 – Arien[...]

  • Page 17

    EN - 17 CONTROLS AND FEA TURES See Figures 14, 15 and 16 for all Controls and Features locat ions. Dual Handle Interlock When Attachment Clutch and then T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released. T o stop attachment, release T raction Drive Clutch and both clutches will disengage. T r ac[...]

  • Page 18

    EN - 18 Forward: (6) Fastest (1) Slowest Reverse: (1) Slow (2) Fast IMPORT ANT : DO NOT change motion from forward to revers e with clutch engaged. Forward speed can be changed without declutching. Fuel Shut-Off V alve IMPORT ANT : The fuel shut-off valve M UST be in the closed position prior to transporting the unit. The fuel shut-off valve has t [...]

  • Page 19

    EN - 19 2. Wait for impeller blades t o stop rotating completely . 3. Remove the snow clean- out tool (1) from the auger housing and use it to remove the clog from the discharge chute. 4. Replace the snow clean-out tool on the auger housing. 5. Reconnect spark plug wire, and re start engine. Manual Dis charge Ch ute Deflector (920013) AL WA YS posi[...]

  • Page 20

    EN - 20 Scraper Blade The scraper blade allows the back of t he housing to keep better contact wit h the surface being c leared. It also prevents damage to the hous ing from wear . IMPORT ANT : DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged. Skid Shoes The skid sho es control the distance between the scrape[...]

  • Page 21

    EN - 21 IMPORT ANT : DO NOT OVERF ILL! This equipment and/or its engine may include evaporative emissions contro l system components, required to meet EP A and/or CARB regulations, that will only function properly when the fuel t ank has been filled to the recomm ended level. Overfilling may cause permanent damage to evaporative emissions control s[...]

  • Page 22

    EN - 22 6. 920014, 020 – Insert key into igniti on switch on engine and rotate int o "Run" position. 920013, 021 – Insert key into ignition switch on engine and push into "Run" position. DO NOT twist key aft er it is inserted. 7. Grasp recoil starter handle and pull rope out slowly until it pulls harder . Let rope rewind slo[...]

  • Page 23

    EN - 23 T RAVELIN G T o travel from one work area to another: 1. 920013, 014, 021 – Press down on handlebars enough to raise front of unit slightly off surface. 920020 – Place t he unit in the Up (Transport) position (see T rack Ang le on page 19). 2. Engage traction drive clutch without engaging attachment clutch. T RANSPORT AL WA YS s hut off[...]

  • Page 24

    EN - 24 MAINTENANC E SCHEDULE The chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent service may be required. CHECK DUAL HANDLE IN TERLO CK Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch should remain engaged until[...]

  • Page 25

    EN - 25 T o ensure adequate lubricant level: 1. Remove oil fill plug and seal w asher (Figure 21). Lubricant must be 1.63 – 1.88" (4.14 – 4.78 cm) from the flat surface of the gear case cover . IMPORT ANT : DO NOT remove the gear case cover . 2. Check oil level with suitable dip stick device. Ad d lubricant if required. NOTICE: Inspect sea[...]

  • Page 26

    EN - 26 GENERAL LUBRICATION (Figures 23 and 24) IMPORT ANT : Wipe each fitting clean before and after lubrication. IMPORT ANT : DO NOT allow grease or oil to get on friction disc, f riction plate or belts. NOTICE: Apply Ariens Hi-T emp Grease or equivalent to the lubrication f ittings. See SERVICE P ARTS on page 38 . Sno-Thro should be lubricated a[...]

  • Page 27

    EN - 27 Figure 24 Grease Oil 92002 0 2x[...]

  • Page 28

    EN - 28 SCRAPER BLADE IMPORT ANT : Damage to housing will result if blade wears down t oo far . Scraper blade is adjustable to compensate for wear . T o adjust scraper blade: 1. Tip unit back onto handlebar , support housing and loosen nuts ret aining blade. 2. Lower s craper blade to com pensate for wear then tighten nuts. 3. Adj ust skid sho es. [...]

  • Page 29

    EN - 29 REMOTE DI SCHARGE DEFLECTOR CONTROL ADJUSTMENT (920014, 020, 021) (Figures 28 and 29) Deflector must stay in selected position while th rowi ng s n ow . If deflector does not stay in set position: 1. Tighten nut beneath control panel to increase press ure on deflector co ntrol (Figure 28). . If deflector does not follow full range of travel[...]

  • Page 30

    EN - 30 DISCHARGE CHUTE (Figure 30) If discharge chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring. SP EED SELECT OR ADJUSTMENT (Figure 31) T o adjust: 1. Disconnect adjustment pivot pin from speed select or arm. Save ha rdware for reinstallati on. 2. Place the speed selector [...]

  • Page 31

    EN - 31 2. Loosen hardware securing belt cover to unit. NOTICE: DO NOT completely remove t he hardware from unit. 3. Remove belt cover . 4. Loosen jam nut on cable adjustment barrel, and then turn the adjustment barrel down to shorten cable and remove all c able slack (Figure 32). 5. With t he attachment clutch disengaged, check that the attachment[...]

  • Page 32

    EN - 32 • If roller is more than 7/8" ( 22.2 mm) from frame, loosen idler adjustment nut and move idler away from the belt. T ighten adjustment n ut and recheck roller clearance (Figure 35) . Check At t achme nt Brake (Figure 36) 1. With t he attachment clutch lever disengaged, brake pad must contact attachment belt. With att achment clutch [...]

  • Page 33

    EN - 33 T RACTION DRIVE CLUTCH ADJUSTMENT If drive slip s, adjust traction clutch to compensate for friction disc wear . 1. Loosen jam nut on traction ca ble adjustment barrel. Turn adjustment barrel down to shorten cable and remove all c able slack. 2. With t raction clutch disengaged, c heck that swing gat e finger touches the s ide of stop hole [...]

  • Page 34

    EN - 34 8. Run in the attachment belt. See Run-in Attac hmen t Be lt on page 13. 9. Replace belt c over and tighten hardware. T RACTION DRIVE BELT REPLA CEMENT (Figure 41) NOTICE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to change traction drive belt. 1. Rem ove attachment drive belt (See [...]

  • Page 35

    EN - 35 6. Install new traction drive belt. 7. Swing dr ive plate toward friction disc until finger lines up w ith stop hole in frame. Slide the drive plate over , inserting the finger into the stop hole. 8. Reinstall swing gate spacer . 9. Reinstall traction idler spring. NOTICE: Make sure dr ive plate return spring remains connected t o the frame[...]

  • Page 36

    EN - 36 1 1. R emove old friction disc . Put the new friction disc in place, cup side to carrier bearing. 12. R einstall three screws into new friction disc and car rier bearing. T orque to 5 – 6 lbf-ft. (6.8 – 8.1 N •m). 13. Insert new friction disc assembly into frame. Install washers onto carrier bearing and slide into speed selector arm. [...]

  • Page 37

    EN - 37 T RACTION T ENSION ADJUSTMENT (920020) (Figures 45 and 46) Check the track tension by applying pressure on the track mi dway between the upper and rear track rollers. Deflection should be approximately 3/8" (9.5 mm) (Figure 45). If deflection is excessive, tighten the track tension. If unit pulls to the lef t or right when a straight p[...]

  • Page 38

    EN - 38 SHORT T ERM IMPORT ANT : NEVER spray unit with high pressure wa ter or store unit outdoors. Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Close fuel shut-off valve. Inspect unit for v isible signs of wear , breakage or damag e. Keep all nuts, bolts and screws properly tightened [...]

  • Page 39

    EN - 39 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ start. 1. F uel tank is empty . 2. F uel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Switch not in run position. 5. Electric starter not functioning. 1. F ill fuel tank. DO NO T OVERFILL! (s ee FIL LING FUEL T ANK on page[...]

  • Page 40

    EN - 40 Unit throws snow poo rly or does not throw snow . 1. Shea r bolts broken. 2. Attachment clutch/brake not adjusted properly . 3. Im peller is frozen in place. 4. Ic e or debris is obstructing auger . 5. Attachment drive belt slipping, worn or damaged. 1. Replace s hear bolts (see Shear Bolts on page 28). 2. Adjust attachment clutch/brake (se[...]

  • Page 41

    EN - 41 SPECIFICA TIONS Model N umber 920013 Description Compact 22 Engine Arien s OHV Gross T or que* – lbf-ft (N•m) 9.5 (12.9) *Engine output stated i n gross torque per SAE J 1940 as rated by engine manufacturer . Displacement – in. ( cc) 12.7 (208) High Idle – RPM (min) 3600 ± 50 Electric S tart 120V Fuel T ank Capacity – qt (Liters)[...]

  • Page 42

    EN - 42 SPECIFICA TIONS Model N umber 920014 Description Compact 24 Engine Briggs & S tratton Polar Force Gross T orque* – lbf-ft (N•m) 9.5 (12.9) *Engine output stated i n gross torque per SAE J1940 as rated by engine manufacturer . Displacement – in. ( cc) 12.7 (208) High Idle – RPM (min) 3600 ± 100 S tart 120 V Fuel T ank Capacity ?[...]

  • Page 43

    EN - 43 SPECIFICA TIONS Model N umber 920020 Description Compact 24 Track Engine Briggs & S tratton Polar Force Gross T orque* – lbf-ft (N•m) 9.5 (12.9) *Engine output stated i n gross torque per SAE J1940 as rated by engine manufacturer . Displacement – in. ( cc) 12.7 (208) High Idle – RPM (min) 3600 ± 100 S tart 120 V Fuel T ank Capa[...]

  • Page 44

    EN - 44 SPECIFICA TIONS Model N umber 920021 Description Compact 24 Engine Arien s OHV Gross T or que* – lbf-ft (N•m) 9.5 (12.9) *Engine output stated i n gross torque per SAE J 1940 as rated by engine manufacturer . Displacement – in. ( cc) 12.7 (208) High Idle – RPM (min) 3600 ± 50 Electric S tart 120V Fuel T ank Capacity – qt (Liters)[...]

  • Page 45

    Sno-Chore _2012_Rev . A 45 Sno-Thro ® , Sno- T ek ® an d Chore Perform ing Equipment Limited W arranty Ariens C ompany (Arie ns) warran ts to the ori ginal pu rchaser that Arien s, Grav ely , P arker , and C ountax brand cho re perfor ming equip ment (i ncluding S no-Thro ® and Sno-T e k ® equipme nt) purcha sed on or after 1/1/2012 will be fre[...]

  • Page 46

    Sno-Chore _2012_Rev . A 46 Exceptions and Limitations The chart below details special e xceptions to this warranty: Custome r R e s pons i bili ti es Regist er the pr oduct i mmediate ly at the time of sale. If the deale r does no t register t he produc t, the customer m ust comple te the pro duct registr ation card i n the literat ure package a nd[...]

  • Page 47

    Sno-Chore _2012_Rev . A 47 Exclusions – Items Not Covered by This W arranty • Parts that a re not genui ne Ariens, Gravely , Parke r or Countax s ervice parts are n ot covered by this warranty an d may void the warran ty . • Damages resulting from the installation or use of any part, accessory , or attachment which is not approved by the Arie[...]

  • Page 48

    Ariens 655 West Ryan St reet Brillion, WI 541 10 920-756-4688 www .ariens.com[...]