Français dropdown-ico

Bixolon SRP-270C manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Bixolon SRP-270C. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Bixolon SRP-270C ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Bixolon SRP-270C décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Bixolon SRP-270C devrait contenir:
- informations sur les caractéristiques techniques du dispositif Bixolon SRP-270C
- nom du fabricant et année de fabrication Bixolon SRP-270C
- instructions d'utilisation, de réglage et d’entretien de l'équipement Bixolon SRP-270C
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Bixolon SRP-270C ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Bixolon SRP-270C et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Bixolon en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Bixolon SRP-270C, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Bixolon SRP-270C, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Bixolon SRP-270C. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    User ’ s Manual SRP-270 Imp act Printer Rev . 1.05 http://www .bixolon.com[...]

  • Page 2

    Rev . 1.05 - 2 - SRP-270 ■ T able of Content s ※ Manual Information & Usage Pr ecautions ................................................................ 3 1. Content C onfirmation .................................................................................................. 7 2. Product Pa rt Names......................................[...]

  • Page 3

    Rev . 1.05 - 3 - SRP-270 ■ Manual Information ※ Manual Information & Usage Precautions This user manual contains basic information for product usage as well as for emergency measures that may be required. ※ The following separate manuals provide more detailed content on various technological issues and areas. 1. Windows Driver Manual This[...]

  • Page 4

    Rev . 1.05 - 4 - SRP-270 ■ Safety Precautions In using the present appliance, please keep the following safety regul ations in order to prevent any hazard or material damage. W ARNING Violating following instructions c an cause serious injury or death. Do not bend the cable b y force or leave it under any heavy objec t. • A damaged ca ble can c[...]

  • Page 5

    Rev . 1.05 - 5 - SRP-270 CAUTION Violatin g following instructions c an cause sligh t wound or damage t he appliance . Do not use the printer when it is out of order . This can cause a fire or an electro cution. • Switch off and unplug the printer before calling your dealer . Do not let water or othe r foreign object s in the printer . • If thi[...]

  • Page 6

    Rev . 1.05 - 6 - SRP-270 ■ Other Precautions The copyright for this user manual and various other manuals is pr operty of the BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permi ssion of BIXOLON Co., Ltd. is strictly prohibited. Use of the information contained in this man[...]

  • Page 7

    Rev . 1.05 - 7 - SRP-270 1. Content Confirmation The following items should all be c ontained in the printer p ackage. Contact the dealer from which the purchas e was made if any it em is damaged and/or missing. SRP-270A SRP-270C SRP-270D Power Cord AC Adapter Paper Roll Ribbon Cartridge Installation Guide CD SRP-270D Exclusive Sp o o l[...]

  • Page 8

    Rev . 1.05 - 8 - SRP-270 2. Product Part Names Cartridge Knob Printer Cover S pool Ribbon Cartridge Auto Cutter Paper Feed Button Power Switch[...]

  • Page 9

    Rev . 1.05 - 9 - SRP-270 3. Installation & Usage 3-1 Power Connection Connect power to the prin ter as shown below . 1) T urn off the printer power switch. 2) Check to see that the AC adapter voltage matches that of the power source. 3) Connect the AC adapter jack to the printer power connector . 4) Connect the power cord to the AC adapter . 5)[...]

  • Page 10

    Rev . 1.05 - 10 - SRP-270 3-2 Interface Cable Connection Connect the printer with a POS system (PC, E CR, etc.) via an interface cable as shown below . This printer supports the following communications interface st andards. - RS-232C (Serial) - RS-485 (Serial) - IEEE1284 (Parallel) - USB 1) T urn off the power switch on both the printer and the PO[...]

  • Page 11

    Rev . 1.05 - 1 1 - SRP-270 3-3 Cash Drawer Connection Connect the printer and cash drawer via the interface cable as shown below . 1) T urn off the power switch on both the printer and the POS system (PC, ECR, etc.). 2) Connect the cash drawer cable to the printer cash drawer connector . ※ CAUTION Do not connect a telephone line to the printer ca[...]

  • Page 12

    Rev . 1.05 - 12 - SRP-270 3-4 Ribbon Cartridge Installation Install the ribbon cartridge as shown below . 1) T urn off the printer power switch. 2) Open the printer cover . 3) Before inserting the ribbon cartridge, turn the cartridge knob clockw ise in order prevent the ribbon from tangling. 4) Insert the ribbon cartridge as shown in t he image abo[...]

  • Page 13

    Rev . 1.05 - 13 - SRP-270 3-5 Paper Installation The paper used varies by printer model. - SRP-270 A/C: 1-layer paper - SRP-270 D: 2-layer paper 3-5-1 SRP-270 A/C Model 1) T urn on the printer power . 2) Open the printer cover . (Remove any core of a fully used paper roll if present.) 3) Undo the paper roll, and make sure that the lower edge is cle[...]

  • Page 14

    Rev . 1.05 - 14 - SRP-270 5) Insert the end of t he paper roll into the p aper slot as shown below . The paper then feeds automatically . Automatic cutting is available for printer models equipped with auto cutters. (SRP-270C) - For printer models without auto cutters, tear of f the paper as shown below . (SRP-270A)[...]

  • Page 15

    Rev . 1.05 - 15 - SRP-270 3-5-2 SRP-270 D Model 1) T urn on the printer power . 2) Open the printer cover . (Remove any core of a fully used paper roll if present.) 3) Undo the paper roll, and make sure that the lower edge is cleanly cut. 4) Insert the paper roll as s hown below . (Exercise special care to align the paper direction correctly .)[...]

  • Page 16

    Rev . 1.05 - 16 - SRP-270 5) Insert the end of t he paper roll into the p aper slot as shown below . The paper then feeds automatically . 6) T urn the spool and insert the p aper into the groove. Wrap the p aper around the spool several times, and then affix into the spool slot. Sp o o l[...]

  • Page 17

    Rev . 1.05 - 17 - SRP-270 7) T ear of f any extruding paper . 8) Close the auto cutter , and then close the printer cover . ( C o r r e c t P a p e r I n s t a l l a t i o n ) ( I n c o r r e c t P a p e r I n s t a l l a t i o n ) Auto Cutter Paper Roll Sp o o l Auto Cutter Paper Roll Sp o o l[...]

  • Page 18

    Rev . 1.05 - 18 - SRP-270 3-6 Control Panel Usage O Feed Press this button to feed paper . This button is also used for self-tests and hexa-printing. - Refer to “4. Self-Test” for details related to self-tests. - Refer to the service manual for information on hexa-printing. O Power This lamp turns green when the printer power is on. O Error Thi[...]

  • Page 19

    Rev . 1.05 - 19 - SRP-270 4. Self-Test Run the self-test when first setting the prin ter or when encountering a problem. The following printer attributes can be assessed. - Control Circuits, Mechanisms, Print Quality , and ROM V ersion If no issue is found with the printer after running the self-test, examine the other devices or peripherals and so[...]

  • Page 20

    Rev . 1.05 - 20 - SRP-270 5. Fine Tuning 5-1 Dip Switch Adjustment The dip switches can be used to select the following printer functions. - Emulation - Auto Cutter, Font In terval, Auto Line Feed - Serial Communications Settings, Hexa-Printing The dip switches are located on the under side of the printer. Dip switch adjustment instructions are as [...]

  • Page 21

    Rev . 1.05 - 21 - SRP-270 [Diagram 1] Switch Functions When Us ing a Serial Interface (RS232C & RS485) [Dip Switch 1 Settings] Switch Function On Off Default SW1-1 Off SW1-2 Emulation Selection Refe r to Chart (1) below . Off SW1-3 Auto Cutter Selection Enable Disable On SW1-4 Font Interval Selection 2 3 Off SW1-5 - SW1-6 - SW1-7 Service T echn[...]

  • Page 22

    Rev . 1.05 - 22 - SRP-270 [Diagram 2] Switch Functions When Using a Parallel or USB Interface [Dip Switch 1 Settings] Switch Function On Off Default SW1-1 Off SW1-2 Emulation Selection Refe r to Chart (1) below . Off SW1-3 Auto Cutter Selection Enable Disable On SW1-4 Font Interval Selection 2 3 Off SW1-5 - SW1-6 - SW1-7 Service T echnician Mode Of[...]

  • Page 23

    Rev . 1.05 - 23 - SRP-270 5-2 Paper Jam Removal Remove jammed paper as shown below . 1) Open the printer cover . 2) Lift the lock mechanism handle and raise the auto cutter . 3) Remove the ribbon cartridge. 4) Use a screwdriver or coin to l oosen the manual screw as shown above. 5) Remove the head cover . Ribbon Cartridge Lock Mechanism Handle Auto[...]

  • Page 24

    Rev . 1.05 - 24 - SRP-270 6) Push the head to the left and fix in place. 7) T urn the paper feed knob and remove the jammed p aper . 8) Replace the head cover and fasten the screw . 9) Place the ribbon cartridge and paper back in their original positions and close the printer cover . ※ WARNING The printer head can get hot during printing. Af ter [...]

  • Page 25

    Rev . 1.05 - 25 - SRP-270 ※ CAUTION If the cutting edge of the auto cutter is not in it s normal posit ion, p aper cannot be inserted properly . Insert a screwdriver into the hole near the bottom of the auto cutter as shown below , and turn the gear within the auto cutter to adj ust the cutting edge to its normal position. Cutting Edge Normal Pos[...]

  • Page 26

    Rev . 1.05 - 26 - SRP-270 6. Appendix 6-1 Specifications Item Description Printing Method Serial Imp a ct Dot Head Pin Number 9 Print Direction T wo-way Print S peed 4.6 LPS (lines per second) Printer Characters Per Line Font A 33 (9*9), Font B 40 (7*9), Korean 20 (17*9) T ype Cartridge type (RRC-201 B/R) Color Black/Red Ribbon Life Black: 1,500,00[...]

  • Page 27

    Rev . 1.05 - 27 - SRP-270 6-2 RS-232C (Serial Interf ace) Cable Specifications 1) Printer Rear Image ※ Turning the dip switch on the Serial inte rface to the ON position connects DTR and R TS signals together . 2) Cable S pecifications (Shield.G) (S.GND) (S.GND) (S.GND) (S.GND) (Shield.G) (Shield.G) (Shield.G) Pin No. Signal Direction Function 1 [...]

  • Page 28

    Rev . 1.05 - 28 - SRP-270 6-3 RS-485 (Serial Interf ace) Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Signal Direction Function 1 FGND - Frame Ground 2 SD2 Output Send Data 3 SD1 Output 4 RD2 Input Receive Data 5 RD1 Input 7 SGND - Signal Ground 8 9 DR2 DR1 Output Same as DTR (RS-232) 10 11 CS2 CS1 Input Same as DSR ([...]

  • Page 29

    Rev . 1.05 - 29 - SRP-270 6-4 IEEE1284 (Parallel Interf ace) Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1 4 Host / Printer Data 2 - Data 2 5 Host / Printer Data 3[...]

  • Page 30

    Rev . 1.05 - 30 - SRP-270 6-5 USB Interface Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Signal Wire Color Function 1 VBUS Red Host Power 2 D- White Data (D-) 3 D+ Green Data (D+) 4 GND Black Signal Ground Shell Shield Drain Wire Frame Ground 6-6 Cash Drawer Cable Specifications Pin No. Signal Direction 1 Frame Ground[...]

  • Page 31

    Rev . 1.05 - 31 - SRP-270 6-7 Certification 1) EMC & Safety S tandards • Europe: CE EMC,CB-Scheme:IE C60950-1, GS: EN60950-1: 2001 • North America: FCC rules parts 15B WARNING Use of an unprotected interface cable with th is printer conflicts with EMC st andards. Users should only use cables approved by BIXOLON. 2) CE Mark • EMC Directive[...]