Français dropdown-ico

Bretford LAP30EULBA manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Bretford LAP30EULBA. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Bretford LAP30EULBA ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Bretford LAP30EULBA décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Bretford LAP30EULBA devrait contenir:
- informations sur les caractéristiques techniques du dispositif Bretford LAP30EULBA
- nom du fabricant et année de fabrication Bretford LAP30EULBA
- instructions d'utilisation, de réglage et d’entretien de l'équipement Bretford LAP30EULBA
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Bretford LAP30EULBA ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Bretford LAP30EULBA et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Bretford en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Bretford LAP30EULBA, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Bretford LAP30EULBA, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Bretford LAP30EULBA. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    LAP30EULBA LAP30EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Qt y . Part No. Description 1 LAP30EULBA Cart Assembly , e-units at back LAP30EULFR Cart Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of cart[...]

  • Page 2

    clip DET AIL 'A' DET AIL 'B' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly[...]

  • Page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 18 screws (2 per shelf) from r[...]

  • Page 4

    DET AIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab[...]

  • Page 5

    Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the rear of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window . 4. Grip the top and tilt to the upright position, underneath top panel bracket. When repositi[...]

  • Page 6

    Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 7 Reinstall 18 scre[...]

  • Page 7

    Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET AIL 'A' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'B' mounting tab[...]

  • Page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the[...]

  • Page 9

    DET AIL 'C' DET AIL 'D' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. re[...]

  • Page 10

    Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'F' Step 5 Reinstall 18 screw[...]

  • Page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit power switch shou[...]

  • Page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET AIL 'A' DET AIL 'B' mounting tab[...]

  • Page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip[...]

  • Page 14

    DET AIL 'C' DET AIL 'D' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left[...]

  • Page 15

    Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window . Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the br[...]

  • Page 16

    notch tab Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 6 Reinsta[...]

  • Page 17

    Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be repl[...]

  • Page 18

    Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET AIL 'A' DET AIL 'B' bracket assembly bracket assembly front-right front-left[...]

  • Page 19

    Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tigh[...]

  • Page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab[...]

  • Page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View).[...]

  • Page 22

    Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . The E-Unit bracket assembly shown above, will need to be removed (with a philips screwdriver) to allow the E- Unit to swing back. This will allow the timer cord plug to pass between the E-Unit and rear panel. bottom flange- timer/brack[...]

  • Page 23

    Step 5 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located abo[...]

  • Page 24

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET AIL 'C' Step 8 Reinstall [...]

  • Page 25

    TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 E-Unit power cord timer assembly bottom shelf Front View Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power cords of the E-Units from the timer assembly[...]

  • Page 26

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET AIL 'A' DET AIL 'B&a[...]

  • Page 27

    DET AIL 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab[...]

  • Page 28

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b[...]

  • Page 29

    Step 6 Remove 2 screws that secure timer to bracket. Step 7 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Timer vents & bracket must be attached as shown.[...]

  • Page 30

    Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf wit[...]

  • Page 31

    DET AIL 'C' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When repositioned[...]

  • Page 32

    1 1 2 2 1 1 1 1 1 1 22 15 19 11 7 16 20 8 12 AUX. 1 3 AUX. 2 4 17 21 13 9 18 22 10 14 AUX. 3 1 5 AUX. 4 2 6 23 27 24 28 25 29 26 30 AUX. 5 AUX . 6 LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation of labels peel off and attach corresponding labels to shelves and E-Units. shelf E-Unit E-Unit E-Unit at rear[...]

  • Page 33

    Part #031-6567 Rev . 12.22.08 CZ P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert “reset” tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e[...]