Chamberlain 3585-100 3/4 HP manuel d'utilisation
- Voir en ligne ou télécharger le manuel d’utilisation
- 36 pages
- 3.22 mb
Aller à la page of
Les manuels d’utilisation similaires
-
Garage Door Opener
Chamberlain 2280C 1/2 HP
72 pages 4.86 mb -
Garage Door Opener
Chamberlain 450
10 pages 1.37 mb -
Garage Door Opener
Chamberlain 801CB
8 pages 0.17 mb -
Garage Door Opener
Chamberlain PD758S 3/4 HP
40 pages 2.59 mb -
Garage Door Opener
Chamberlain 4200C
80 pages 2.55 mb -
Garage Door Opener
Chamberlain 600A
9 pages 2.02 mb -
Garage Door Opener
Chamberlain 1140
32 pages 2.49 mb -
Garage Door Opener
Chamberlain 985
36 pages 0.88 mb
Un bon manuel d’utilisation
Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Chamberlain 3585-100 3/4 HP. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Chamberlain 3585-100 3/4 HP ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.
Qu'est ce que le manuel d’utilisation?
Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Chamberlain 3585-100 3/4 HP décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.
Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.
Donc, ce qui devrait contenir le manuel parfait?
Tout d'abord, le manuel d’utilisation Chamberlain 3585-100 3/4 HP devrait contenir:
- informations sur les caractéristiques techniques du dispositif Chamberlain 3585-100 3/4 HP
- nom du fabricant et année de fabrication Chamberlain 3585-100 3/4 HP
- instructions d'utilisation, de réglage et d’entretien de l'équipement Chamberlain 3585-100 3/4 HP
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes
Pourquoi nous ne lisons pas les manuels d’utilisation?
Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Chamberlain 3585-100 3/4 HP ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Chamberlain 3585-100 3/4 HP et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Chamberlain en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Chamberlain 3585-100 3/4 HP, comme c’est le cas pour la version papier.
Pourquoi lire le manuel d’utilisation?
Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Chamberlain 3585-100 3/4 HP, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.
Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Chamberlain 3585-100 3/4 HP. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.
Table des matières du manuel d’utilisation
-
Page 1
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Models 3585 3/4 HP 3585-100 3/4 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT[...]
-
Page 2
2 Introduction 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .....................................................................4 Carton inventory .......................[...]
-
Page 3
3 T o prevent damage to garage door and opener: • AL WA YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJURY OR DEA TH: • AL WA YS call a trained door systems technician if garage door binds, sticks, or is out of ba[...]
-
Page 4
FI N ISHED CEILI N G S u pport b racket & fastening hard w are is re qu ired. See page 12. Safety Re v ersing Sensor Header W all Access Door Safety Re v ersing Sensor Gap b et w een floor and b ottom of door m u st not exceed 1/4" (6 mm) W all- mo u nted Door Control Motor Unit ONE-PIECE DOOR WITHOUT TRACK 4 Planning Identify the type and[...]
-
Page 5
5 Y our garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below . Carton Inventor y Straight Door Arm Sectio[...]
-
Page 6
T o avoid SERIOUS damage to opener , ONL Y use bolts/fasteners mounted in top of motor unit. WARN ING CAUTION WARN ING WARN ING ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the bolt and lock nut from the top of the motor unit. • Plac[...]
-
Page 7
7 INST ALLA TION IMPORT ANT INST ALLA TION INSTRUCTIONS T o reduce the risk of SEVERE INJUR Y or DEA TH: WARN ING WARN ING WARN ING 1. READ AND FOLLOW ALL INST ALLA TION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener only on properly balanced and lubricated garage door . An improperly balanced door may not reverse when required and could [...]
-
Page 8
8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket withi[...]
-
Page 9
9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HEA[...]
-
Page 10
Header Bracket Belt P u lley Bracket T emporary S u pport Header W all Garage Door Cle v is Pin 5/16"x2-3/4" Ring Fastener Header Bracket Belt P u lley Bracket Rail 10 Clevis Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bra[...]
-
Page 11
11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail.[...]
-
Page 12
Measure Distance Lag Screws 5/16"-18x1-7/8" Structural Supports Bracket (Not Provided) Lag Screws 5/16"-18x1-7/8" (Not Provided) Bolt 5/16"-18x7/8" Lock W asher 5/16" Nut 5/16"-18 FINISHED CEILING Hidden Support Bolt 5/16"-18x7/8" Lock W asher 5/16" Nut 5/16"-18 Bolt 5/16"-18x7/8"[...]
-
Page 13
13 To release wire, push in tab with screwdriver tip Door Control Connections 7/16" (11 mm) Strip wire 7/16" (11 mm) Red Grey White INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and [...]
-
Page 14
Lens Hinge 100 Watt (Max) Standard Light Bulb Release Tab 100 Watt (Max) Standard Light Bulb 14 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in [...]
-
Page 15
15 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, conta[...]
-
Page 16
16 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct[...]
-
Page 17
17 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 WALL MOUNT (RIGHT SI[...]
-
Page 18
In v isi b le Light Beam Sensor Connect W ire to Opener Q u ick-Connect T erminals Bell W ire Bell W ire Finished Ceilin g Q u ick-Connect T erminals 3. Insert into appropriate terminals 1. Strip w ire 7/16" (1 1 mm) 2. T w ist like colored w ires together 7/16" (1 1 mm) Red Grey W hite 18 Carriage Bolt 1/4"-20x1/2" Lens W ing N[...]
-
Page 19
19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following p[...]
-
Page 20
20 Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. MET AL DOOR Top of Door (Inside Garage) Door Bracket Optional[...]
-
Page 21
21 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t[...]
-
Page 22
22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adj[...]
-
Page 23
23 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev[...]
-
Page 24
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather [...]
-
Page 25
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t[...]
-
Page 26
OPERA TION 26 IMPORT ANT SAFETY INSTRUCTIONS T o reduce the risk of SEVERE INJUR Y or DEA TH: Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Securit[...]
-
Page 27
Using the W all-Mounted Door Control THE MOTION DETECTING DOOR CONTROL Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening. This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garag[...]
-
Page 28
CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse tes[...]
-
Page 29
29 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins[...]
-
Page 30
Bell W ire Safety Sensor "Learn" Button LED or Diagnostic LED Diagnostics Located On Motor Unit 30 Installed Safety Sensor Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Cha[...]
-
Page 31
*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er[...]
-
Page 32
32 T o Add, Reprogram or Change a Keyless Entry PIN NOTE: Y our new Keyless Entry must be programmed to operate your garage door opener . USING THE “LEARN” BUTTON USING THE MOTION DETECTING DOOR CONTROL 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER [...]
-
Page 33
2 5 6 1 3 7 8 4 33 REP AIR P ARTS Rail Assembly Parts KEY P ART NO . NO . DESCRIPTION 1 4A1008 Master link kit 2 41B5424 Belt pulley bracket 3 41B3869-1 Complete trolley assembly 4 109B33 T rolley clip 5 2777BD One-piece T -rail 6 41A5434-1 1 Full belt assembly 7 41B4103 T ensioner assembly 8 83A1 1-2 Rail grease 7 10 11 5 N O TIC E U P C E I L I N[...]
-
Page 34
Motor Unit Assembly Parts 34 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 1 15 19 8A 17 5 18 9 10 16 14 13 12 6 6 11 8B 8C 7 7 KEY P ART NO . NO . DESCRIPTION 1 41A4371 Belt Cap 2 41A4885-5 Gear and sprocket assembly Complete with: Spring washer , thrust washer , retaini[...]
-
Page 35
35 ACCESSORIES 370LM 2778BD 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.4 m) Complete Rail: T o allow an 8 foot (2.4 m) door to open fully . 10 Foot (3 m) Complete Rail: T o allow a 10 foot (3 m) door to open fully . [...]
-
Page 36
© 2006, The Chamberlain Group, Inc. 1 14A3087E All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SER VICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS Y OUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Std. Time) 6:00 A.M. T O 7:00 P .M. - Monda[...]