Chevrolet 2009 Traverse manuel d'utilisation

Seats and Restraint System ............................... 1 - 1 Head Restraints .............. 1 - 2 Front Seats .................... 1 - 3 Rear Seats .................... 1 - 9 Safety Belts .................. 1-14 Child Restraints ............. 1-27 Airbag System .............. 1-46 Restraint System Check ...................... 1-59 Features and Controls ...... 2 - 1 Keys ............................. 2 - 2 Doors and Locks ............ 2 - 8 Windows ...................... 2-14 Theft-Deterrent Systems ................... 2-16 Starting and Operating Your Vehicle ............. 2-20 Mirrors ......................... 2-31 Object Detection Systems ................... 2-36 OnStar ® System ......[...]

GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, are registered trademarks, and the name Traverse is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without further notice. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. This manual describes features that may or may not be on your specific vehicle. Read this owner manual from beginning to end to learn about the vehicle’s features and controls. Pictures, symbols, and words work together to e[...]

Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning. { CAUTION These mean there is something that could hurt you or other people. Cautions tell what the hazard is and what to do to avoid or reduce the hazard. Read these cautions. A notice tells about something that can damage the vehicle. Notice: These mean there is something that could damage your vehicle. Many times, this damage would not be covered by the vehicle’s warranty, and it could be costly. The notice te[...]

Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant Temperature O : Exterior Lamps # : Fog Lamps . : Fuel Gage + : Fuses i : Headlamp High/Low-Beam Changer j : LATCH System Child Restraints * : Malfunction Indicator Lamp : : Oil Pressure g : Outside Power Foldaway Mirrors } : Power / : Remote Vehicle Start > : Safety Belt Reminders 7 : Tire Pressure Monitor _ : T[...]

Seats and Restraint System Head Restraints Head Restraints ................... .1-2 Front Seats Manual Seats ...................... .1-3 Seat Height Adjuster ............. .1-3 Power Seats ........................ .1-4 Manual Lumbar .................... .1-4 Power Lumbar ..................... .1-5 Heated Seats ...................... .1-5 Heated and Cooled Seats ..... .1-5 Memory Seat and Mirrors ...... .1-6 Reclining Seatbacks ............. .1-8 Rear Seats Rear Seat Operation ............. .1-9 Third Row Seats ................ .1-12 Safety Belts Safety Belts: They Are for Everyone ......................... .1-14 How to Wear Safety Belts Properly ........................... .1-17 Lap-Shoulder[...]

Head Restraints The vehicle’s front seats have adjustable head restraints in all outboard seating positions. { CAUTION With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it. To lower the head restraint, press the release button, located on the head restraint post on the top of the seat[...]

Front Seats Manual Seats { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. A. Manual Seat Adjustment Bar B. Driver Seat Height Adjuster. See Seat Height Adjuster on page 1-3 . C. Manual Reclining Seatback Lever. See Reclining Seatbacks on page 1-8 . If the vehicle has a manual bucket seat you can adjust the seat forward or rearward with the bar located under the front of the seat cushion. Lift the bar to unlock the seat. Slide the seat to where you want it and[...]

Power Seats A. Power Seat Adjustment Control B. Reclining Seatbacks on page 1-8 . C. Power Lumbar on page 1-5 . If the vehicle has power seats, the controls are located on the outboard side of the seats. Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. The vehicle may have additional features to adjust the power seat: • Raise or lower the entire seat by moving the power seat adjustment control (A) up or down. • Raise or lower the front part of the seat cushion by moving the front of the control up or down. • Raise or lower the rear part of the seat cushion by moving the rear of the control up or down. The vehicle may have a memory [...]

Power Lumbar If the seats have power lumbar, the controls used to operate this feature are located on the outboard side of the seats. See “Power Lumbar” under Power Seats on page 1-4 for more information. To increase or decrease lumbar support, press and hold the front or rear of the control (C). Release the control when the seatback reaches the desired level of lumbar support. The lumbar support may need to be adjusted when changing the seating position. Heated Seats On vehicles with heated front seats, the controls are located on the center console. To operate the heated seats the engine must be running. I (Heated Seatback): Press to turn on the heated seatback. J (Heated Seat and Seat[...]

z (Heated Seat and Seatback): To heat the entire seat, press the button with the heated seat and seatback symbol. This symbol will appear on the climate control display to indicate that the feature is on. Press the button to cycle through the temperature settings of high, medium, and low and to turn the heated seat off. Indicator bars next to the symbol designate the level of heat selected: three for high, two for medium, and one for low. The heated and cooled seats will be canceled after the ignition is turned off. To use the heated and cooled seat feature after the vehicle is started, you will need to press the appropriate seat button again. Memory Seat and Mirrors On vehicles with the mem[...]

See “MEMORY SEAT RECALL” under DIC Vehicle Customization (With DIC Buttons) on page 3-65 for more information. To stop recall movement of the memory feature at any time, press one of the power seat controls, memory buttons, or power mirror buttons. If something has blocked the driver seat while recalling a memory position, the driver seat recall may stop working. If this happens, press the appropriate control for the area that is not recalling for two seconds, after the obstruction is removed. Then try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not being recalled, see your dealer/retailer for service. Easy Exit Seat The [...]

Reclining Seatbacks Manual Reclining Seatbacks { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. { CAUTION If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. In vehicles with seats that have manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat. To recline the sea[...]

{ CAUTION Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either. In a crash, the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly. Do no[...]

Entering and Exiting the Third Row { CAUTION Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. To access the third row: 1. Remove objects on the floor in front of or on the second row seat, or in the seat tracks on the floor. 2. Move the front center console a[...]

Returning the Seat to the Seating Position To return the second row seat to its normal seating position: 1. Remove objects on the floor behind the second row seat or in the seat tracks on the floor. 2. Pull the seatback rearward until it is locked in place. 3. Slide the seat rearward by pushing on the seatback until it is locked into place. 4. Push down on the rear of the seat cushion until it is locked in place. 5. Push and pull on the seatback and seat cushion to make sure they are locked in place. 6. Check that the safety belt is not under the seat cushion. Reclining the Seatbacks To recline the seatback: 1. Leaning forward in the seat, pull the reclining seatback strap (B). 2. Move the[...]

Third Row Seats { CAUTION Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. The third row seats can be folded forward or removed. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. To fold the seatback: 1. Remove anything on or under the seat. 2. Disconnect the rear safety belt mini-latch, usin[...]

2. The headrest must be locked into place before sitting in the seat. { CAUTION If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push and pull on the seatback to make sure it is locked in place. { CAUTION A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the (Continued) CAUTION (Continued) rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not [...]

Remove the bolts from the holes in the floor before installing the seats. 2. Place the seat on the vehicle floor so that the front seat hooks are on the vehicle bars. 3. Reinstall the bolts, and torque to 55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place. 4. Raise the seatback to its upright position. Push and pull on the seatback to make sure it is locked into place. 5. Push the headrest up into position. Push and pull on the headrest to make sure it is locked into place. 6. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist. Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts [...]

A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without safety belts they could have been badly hurt or killed. After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter... a lot! Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it is just a seat on wheels. Put someone on it. Seats and Restraint System 1-15[...]

Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... or the safety belts! 1-16 Seats and Restraint System[...]

With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down. Q: If my vehicle has airbags, why should I have to wear safety belts? A: Airbags are supplemental systems only; so [...]

Occupants who are not buckled up can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. First, before you or your passenger(s) wear a safety belt, there is important information you should know. Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder a[...]

Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injur[...]

Q: What is wrong with this? A: The belt is over an armrest. { CAUTION You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force (Continued) CAUTION (Continued) would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the[...]

Q: What is wrong with this? A: The belt is behind the body. { CAUTION You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread im[...]

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Third Row Seats on page 1-12 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unloc[...]

See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 6. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull the stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Slide the latch plate up the safety belt webbing when the safety belt is not in use. The latch plate should rest on the stitching on the safety belt, near the guide loop on the side wall. Before a door is closed, be sure the safety belt is out of the way. If a door is slammed agai[...]

You can move the height adjuster up by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without pushing the button to make sure it has locked into position. Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. And, for vehicles with side impact airbags, safety belt pretensioners can help tighten the s[...]

To access the comfort guide, you will first need to move the headrest forward by pulling on the handle behind the seatback. The comfort guide will now be accessible. Pull the comfort guide out of its storage location and then return the headrest to its upright position. The elastic cord on the comfort guide is adjustable. You can make it longer or shorter by squeezing both ends of the plastic adjuster. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. Third Row Center Position Seats and Restraint System 1-25[...]

{ CAUTION A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide into its storage location or on its storage clip. Safety Belt Use During Pregnancy Safety belts work for everyone, inc[...]

The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. To help avoid personal injury, do not let someone else use it, and use it only for the seat it is made to fit. The extender has been designed [...]

Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child’s pelvic bones in a crash. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash. Also see “Rear Safety Belt Comfort Guides” under Lap-Shoulder Belt on page 1-22 . According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint s[...]

{ CAUTION Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury. The child might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance trave[...]

{ CAUTION Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms. An infant should be secured in an appropriate restraint. { CAUTION Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child (Continued) CAUTION (Continued) restraint in a rear seat. It is also better to s[...]

Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufacturer’s ins[...]

Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child’s body with the harness. A booster seat (C) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. (A) Rear-Facing Infant Seat (B) Forward-Facing Child Seat (C) Booster Seats 1-32 Seats and Restraint System[...]

Securing an Add-On Child Restraint in the Vehicle { CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system. See Lower Anchors and Tethers for Children (LATCH) on page 1-35 for more information. A ch[...]

A label on the sun visor says, “Never put a rear-facing child restraint in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position. (Continued) CAUTION (Continued) Even if the passenger sensing system has turned off the right front passenger [...]

Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system. Make sure that a LATCH-compatible child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual. When installing a child restraint with a top tether, you must also use either the lower anchors or the safety belts to properly[...]

Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. Be sure to read and follow the instructions for your child restraint. If the child restraint does not have a top tether, one can be obtained, in kit form, for many child restraints. Ask the child restraint manufacturer whether or not a kit is available. Lower Anchor and[...]

i (Top Tether Anchor): Seating positions with top tether anchors. To assist you in locating the lower anchors, each second row anchor position has a label, near the crease between the seatback and the seat cushion. To assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover or near the anchor. The top tether anchors are located at the bottom rear of the seatback for each seating position in the second row. Open the cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. The third row has one top tether anchor located at the bottom rear of the cent[...]

Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. See Where to Put the Restraint on page 1-33 for additional information. Securing a Child Restraint Designed for the LATCH System { CAUTION If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-t[...]

{ CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return t[...]

2.3. Route, attach and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has a fixed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint. 1-40 Seats and Restraint System[...]

If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-35 for how and where to install the child restraint using LATCH. If a child restraint is secured in the vehicle using a safety belt[...]

3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the [...]

See Lower Anchors and Tethers for Children (LATCH) on page 1-35 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it. Securing a Child Restraint in the Right Front Seat Position The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-33 . In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag and seat-mounted side [...]

install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-35 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. You will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the[...]

5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure. If the airbags are off, the of f indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indi[...]

Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger. • A roof-rail airbag for the driver, passenger seated directly behind the driver, and the third row outboard passenger position. • A roof-rail airbag for the right front passenger, passenger seated directly behind the right front passenger, and the third row outboard passenger position. All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. For front[...]

{ CAUTION Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with airbags. The driver should sit as far back as possible while still maintaining control of the vehicle. Occupants should not lean on or sleep against the door or side windows in seating positions with seat-mounted side impact airbags and/or roof-rail airbags. { CAUTION Children wh[...]

Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side. The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door. Driver Side shown, Passenger Side similar 1-48 Seats and Restraint System[...]

The roof-rail airbags for the driver, right front passenger, passengers behind the driver and right front passenger, and the third row outboard passengers are in the ceiling above the side windows. { CAUTION If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat accessories that block the inflation path of a seat-mounted side impact airbag. Never secure [...]

Frontal airbags may inflate at different crash speeds. For example: • If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. • If the vehicle hits an object that deforms, the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform. • If the vehicle hits a narrow object (like a pole), the airbags could inflate at a different crash speed than if the vehicle hits a wide object (like a wall). • If the vehicle goes into an object at an angle, the airbags could inflate at a different crash speed than if the vehicle goes straight into the object. Thresholds [...]

What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy. The inflator, the airbag, and related hardware are all part of the airbag module. Frontal airbag modules are located inside the steering wheel and instrument panel. For vehicles with seat-mounted side impact airbags, there are airbag modules in the side of the front seatbacks closest to the door. For vehicles with roof-rail airbags, there are airbag modules in the ceiling of the vehicle, near the side windows that have occupant seating positions. How D[...]

The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { CAUTION When an airbag inflates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have (Continued) CAUTION (Continued) breathing problems but cannot get out of the vehicle a[...]

Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. The words ON and OFF, or the symbol for on and off, are visible during the system check. If you are using remote start, if equipped, to start the vehicle from a distance, you may not see the system check. When the system check is complete, either the word ON or OFF, or the symbol for on or off, will be visible. See Passenger Airbag Status Indicator on page 3-33 . The passenger sensing system turns off the right front passenger frontal airbag under certain conditions. The driver ai[...]

A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the right front passenger frontal airbag, no (Continued) CAUTIO[...]

For some children, including children in child restraints, and for very small adults, the passenger sensing system may or may not turn off the right front passenger frontal airbag, depending upon the person’s seating posture and body build. Everyone in the vehicle who has outgrown child restraints should wear a safety belt properly — whether or not there is an airbag for that person. { CAUTION If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-33 for more information, including important safety informati[...]

If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers. 3. Place the seatback in the fully upright position. 4. Have the person sit upright in the seat, centered on the seat cushion, with legs comfortably extended. 5. Restart the vehicle and have[...]

• Liquid pooled on the seat that has not soaked in may make it more likely that the passenger sensing system will enable (turn on) the passenger airbag while a child restraint or child occupant is on the seat. If the passenger airbag is turned on, the on indicator will be lit. If the passenger seat gets wet, dry the seat immediately. If the airbag readiness light is lit, do not install a child restraint or allow anyone to occupy the seat. See Airbag Readiness Light on page 3-33 for important safety information. The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat. If this is not desired remove t[...]

Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly. Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module, steering wheel, instrument panel, roof-rail airbag modules, ceiling headliner or pillar garnish trim, front sensors, side impact sensors, rollover sensor module, or airbag wiring can affect the operation of the airbag system. In addition, the vehicle has a pass[...]

Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will affect my airbag system? A: If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 7-1 . In addition, your dealer/retailer and the service manual have information about the location of the airbag sensors, sensing and diagnostic module and airbag wiring. Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, an[...]

Replacing Restraint System Parts After a Crash { CAUTION A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. If the vehicle has been in a crash, do you need new safety belts or LATCH system (if equipped) parts? After a very minor crash, nothing may be necessary. But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer/retailer to have the safety belt ass[...]

Features and Controls Keys Keys .................................. .2-2 Remote Keyless Entry (RKE) System .................... .2-3 Remote Keyless Entry (RKE) System Operation ...... .2-4 Remote Vehicle Start ............ .2-6 Doors and Locks Door Locks ......................... .2-8 Power Door Locks ................ .2-8 Delayed Locking .................. .2-8 Programmable Automatic Door Locks ........................ .2-9 Rear Door Security Locks ...... .2-9 Lockout Protection ................ .2-9 Liftgate .............................. .2-10 Power Liftgate .................... .2-11 Windows Windows ........................... .2-14 Power Windows ................. .2-14 Sun Visors .......[...]

Storage Areas Glove Box ......................... .2-52 Cupholders ........................ .2-52 Instrument Panel Storage ..... .2-52 Center Console Storage ...... .2-52 Second Row Center Console ........................... .2-53 Floor Mats ......................... .2-54 Luggage Carrier ................. .2-54 Convenience Net ................ .2-55 Cargo Cover ...................... .2-55 Cargo Tie Downs ............... .2-55 Cargo Management System ............................ .2-55 Sunroof Sunroof ............................. .2-56 Keys { CAUTION Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. T[...]

If you are locked out of the vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-6 . Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This de[...]

Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3 . / (Remote Vehicle Start): For vehicles with this feature, see Remote Vehicle Start on page 2-6 for additional information. Q (Lock): Press to lock all the doors. If enabled through the Driver Information Center (DIC), the parking lamps flash once to indicate locking has occurred. If enabled through the DIC, the horn sounds when Q is pressed again within five seconds. See DIC Vehicle Customization (With DIC Buttons) [...]

L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate the panic alarm. The parking lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns off when the ignition is moved to ON/RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work. Programming Transmitters to the Vehicle Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/ retailer. When the replacement transmitter is programmed to this vehicle using [...]

Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. If the vehicle has an automatic climate control system, the climate control system defaults to a heating or cooling mode depending on the outside temperatures. If the vehicle does not have an automatic climate control system, the system turns on at the setting the vehicle was set to when the vehicle was last turned off. If the vehicle has an automatic climate control system and heated seats, the heated seats turn on during colder outside temperatures and shut off when the key is turned to ON/RUN. See Heated Seats on page 1-5 or Heated and Cooled Seats on page 1-5 for more [...]

3. If it is the first remote start since the vehicle has been driven, repeat these steps while the engine is still running, to extend the time by 10 minutes for the engine to continue to run. Remote start can be extended one time. After entering the vehicle during a remote start, insert and turn the key to the ON/RUN position to drive the vehicle. If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done. To manually shut off a remote start: • Aim the RKE transmitter at the vehicle and press / until the parking lamps turn off. • Turn on the hazard warning flashers. • Turn the ignition switch on and then off. The vehicle can be st[...]

Doors and Locks Door Locks { CAUTION Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven. (Continued) CAUTION (Continued) • Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever leaving it. • Out[...]

This feature will not operate if the key is in the ignition. This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under DIC Vehicle Customization (With DIC Buttons) on page 3-65 . Programmable Automatic Door Locks Vehicles with an automatic lock/unlock feature enable you to program the vehicle’s power door locks. This feature can be programmed through the Driver Information Center (DIC). See DIC Vehicle Customization (With DIC Buttons) on page 3-65 for more information. Rear Door Security Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside. Open the rear doors to access the securi[...]

Liftgate { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open: • Close all of the windows. • Fully open the air outlets on or under the instrument panel. (Continued) CAUTION (Continued) • Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. • I[...]

Power Liftgate Power Liftgate Operation { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open: • Close all of the windows. • Fully open the air outlets on or under the instrument panel. (Continued) CAUTION (Continued) • Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Con[...]

• Press the liftgate button on the center console. • Press the touchpad switch on the outside liftgate handle. Pressing the buttons or touchpad switch a second time while the liftgate is moving reverses the direction. The liftgate can also be closed by pressing the power liftgate button next to the liftgate latch. Press the button a second time during liftgate operation to reverse the operation. The power liftgate may be temporarily disabled under extreme temperatures or under low battery conditions. If this occurs, the liftgate can still be operated manually. If the vehicle is shifted out of P (Park) while the power function is in progress, the liftgate power function will continue to c[...]

After removing the obstruction, the power liftgate operation can be used again. If the liftgate comes across more obstacles on the same power cycle, the power function deactivates, and you must manually open or close the liftgate. A message displays, LIFTGATE OPEN, to indicate that the liftgate is open. See Driver Information Center (DIC) on page 3-44 for more information. After removing the obstructions, manually open the liftgate to the full open position or close the liftgate to the fully closed and latched position. The liftgate resumes normal power operation. Pinch sensors are located on the side edges of the liftgate. If an object is caught between the liftgate and the vehicle and pres[...]

Windows { CAUTION Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. Power Windows { CAUTION Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. [...]

The power window controls are located on each of the side doors. The driver door also has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ACCESSORY, ON/RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-22 . Press the switch to lower the window. Pull up on the front edge of the switch to raise the window. Express-Down Windows The express-down feature allows the windows to be lowered without holding the switch. Press the window switch fully and release it to activate the express-down feature. The express mode can be canceled by pressing or pulling the switch. Express-Up Window The express-up [...]

Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed. Window Lockout o (Window Lockout): The window lockout switch is located with the power window switches on the driver door armrest. This feature prevents the rear passenger windows from operating the windows, except from the driver position. Press the switch to turn the lockout feature on or off. An indicator light will come on to show the lockout feature is on. Sun Visor[...]

When the door is closed, the security light stops flashing and stays on solid for approximately 30 seconds. The content theft deterrent alarm is not armed until the security light goes off. If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off. • Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off. The content theft deterrent alarm is not armed until the security light goes off. The theft-deterrent system will not activate if the doors are locked with the vehicle’s key or the manual door lock. If a locked door is opened without using the RKE tran[...]

PASS-Key ® III+ Electronic Immobilizer The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired[...]

When the PASS-Key ® III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key and check the fuses. See Fuses and Circuit Breakers on page 5-86 for additional information. If the engine still does not start with the other key, the vehicle needs servic[...]

If the PASS-Key ® III+ key is lost or damaged, see your dealer/retailer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See DIC Warnings and Messages on page 3-56 for additional information. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • If you have all-wheel drive, keep your speed at 55 mph (88 km/h) or less f[...]

Ignition Positions The ignition switch has four different positions. In order to shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. ( (LOCK/OFF): This position locks the ignition and transmission. The key can be removed in LOCK/OFF. The shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF. The steering can bind with the wheels turned off center. If this happen[...]

Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the ignition key is turned off: • Audio System • Power Windows • Sunroof (if equipped) Power to the windows and sunroof will work up to 10 minutes or until a door is opened. The radio continues to work for 10 minutes or until the driver’s door is opened. For an additional 10 minutes of operation, close all the doors and turn the key to ON/RUN and then back to LOCK/OFF. All these features will work when the key is in the ON/RUN or ACC/ACCESSORY positions. Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the engi[...]

Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go o[...]

3. Plug the cord into a normal, grounded 110-volt AC outlet. { CAUTION Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. The length of time the heater should remain plugged in depends on several factors. Ask a dealer/retailer in the a[...]

press the shift lever button before shifting from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever, then push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 2-29 . R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. To rock the vehicle back and forth to get out of snow, ice or sand without da[...]

Electronic Range Select (ERS) Mode ERS mode allows you to choose the top-gear limit of the transmission and the vehicle’s speed while driving down hill or towing a trailer. The vehicle has an electronic shift position indicator within the instrument panel cluster. When using the ERS Mode a number will display next to the L, indicating the current gear that has been selected. To use this feature: 1. Move the shift lever to L (Low). 2. Press the plus/minus button located on the shift lever, to increase or decrease the gear range available. When you shift from D (Drive) to L (Low), the transmission will shift to a pre-determined lower gear range. The highest gear available for this pre-determ[...]

When Tow/Haul is activated the Tow/Haul symbol will come on the instrument panel cluster. See “Tow/Haul Mode” under Towing a Trailer on page 4-25 for more information. Automatic Engine Grade Braking Automatic Engine Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle. The system will automatically command downshifts to reduce vehicle speed, until the brake pedal is no longer being pressed. While in the Electronic Range Select (ERS) mode, grade braking is deactivated, allowing the driver to select a range and limiting the highest gear available. Grade[...]

Shifting Into Park { CAUTION It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-25 . 1. Hold the brake pedal down and set the parking brake. See Parking Brake on page 2-27 for more information. 2. Move the shift lever into P (Park) by holding in the button on the shift lever and pushing the shift lever all the way toward the front of[...]

If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park). Shifting Out of Park The vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and • Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/ACCESSORY and the regular brake pedal is applied. The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If the vehicle has an [...]

Engine Exhaust { CAUTION Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). • The exhaust smells or sounds strange or different. • The exhaust system leaks due to corrosion or damage. • The vehicle’s exhaust system has been modified, damaged or improperly repaired. (Continued) CAUTION (Continued) • There are holes or openings in the vehicle body from damage or after-market modifications that are not completely sealed. If unusu[...]

{ CAUTION It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). Follow the proper steps to be sure the vehicle will not move. See Shifting Into Park on page 2-28 . If parking on a hill and pulling a trailer, see Towing a Trailer on page 4-25 . Mirrors Manual Rearv[...]

Automatic Dimming Mirror Operation Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water. Outside Power Mirrors Controls for the outside power mirrors are located on the driver door armrest. To adjust each mirror: 1. Press (A) or (B) to select the driver or passenger side mirror. 2. Press one of the four arrows located on the control pad to adjust the mirror. 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be se[...]

Outside Power Foldaway Mirrors Vehicles with outside power foldaway mirrors, have the controls located on the driver door armrest. Mirror Adjustment 1. Press (C) to fold the mirrors out to the driving position. 2. Press (D) to fold the mirrors in to the folded position. Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if: • The mirrors are accidentally obstructed while folding. • They are accidentally manually folded/unfolded. • The mirrors vibrate at normal driving speeds. Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power foldaway mirrors. This sound[...]

Blind Spot Mirrors The blind spot mirror is a small convex mirror built into the upper and outer corner of both outside mirrors. It is designed to increase driver visibility and show objects that may be in the vehicle’s blind zone. Driving with the Blind Spot Mirror The illustration represents how a vehicle appears in the blind spot mirror when a vehicle is approaching the blind zone. 1. When the approaching vehicle is a long distance away, the image in the main mirror is small and near the inboard edge of the mirror. 2. As the vehicle gets closer, the image in the main mirror gets larger and moves outboard. 3. As the vehicle enters the blind zone, the image transitions from the main mirro[...]

Using the Outside Mirror with the Blind Spot Mirror 1. Set the main mirror so that the side of your vehicle can just be seen and your blind spot mirror has an unobstructed view. 2. When checking for traff ic or before changing a lane, look at the main driver/passenger side mirror to observe traff ic in the adjacent lane, behind your vehicle. Check the blind spot mirror for a vehicle in the blind zone. Then, glance over your shoulder to double check before moving slowly into the adjacent lane. Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse)[...]

Object Detection Systems Ultrasonic Rear Parking Assist (URPA) For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 5 mph (8 km/h), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 8 feet (2.5 m) behind the vehicle, and at least 10 inches (25.4 cm) off the ground. { CAUTION The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: • objects that are below the bumper, underneath the vehicle, or if they are too close or far from the vehicle • children, pedestrians, bicyclists, or pets. If you [...]

How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). The rear display briefly illuminates to indicate the system is working. URPA operates only at speeds less than 5 mph (8 km/h). If the vehicle is above this speed, the red light on the rear display flashes. To be detected, objects must be at least 10 inches (25.4 cm) off the ground and below liftgate level. Objects must also be within 8 feet (2.5 m) from the rear bumper. This distance may be less during warmer or humid weather. A single beep sounds the first time an object is detected. Beeping may occur beginning at 23 inches (0.6 m). Beeping occurs for a short time when the vehicle is closer t[...]

When the System Does Not Seem to Work Properly If the URPA system does not activate due to a temporary condition, the message PARK ASSIST OFF displays on the DIC and a red light will be shown on the rear URPA display when the shift lever is moved into R (Reverse). This may occur under the following conditions: • The driver disables the system. • The ultrasonic sensors are not clean. Keep the vehicle’s rear bumper free of mud, dirt, snow, ice and slush. For cleaning instructions, see Washing Your Vehicle on page 5-81 . • A trailer was attached to the vehicle, or a bicycle or an object was hanging out of the liftgate during the last drive cycle, the red light may illuminate in the rear[...]

CAUTION (Continued) So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the RVC system, always check carefully before backing up by checking behind and around the vehicle. Vehicles Without Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the key is in the ON/RUN position and the driver shifts the vehicle into R (Reverse), the video image automatically appears on the inside rear view mirror. Once the driver shifts out of R (Reverse), the video image autom[...]

3. Select the Rear Camera Options screen button. The Rear Camera Options screen displays. 4. Select the Video screen button. When the Video screen button is highlighted the RVC system is on. The delay that is received after shifting out of R (Reverse) is approximately 10 seconds. The delay can be cancelled by performing one of the following: • Pressing a hard key on the navigation system. • Shifting in to P (Park). • Reach a vehicle speed of 5 mph (8 km/h). There is a message on the rear vision camera screen that states “Check Surroundings for Safety”. Adjusting the Brightness and Contrast of the Screen To adjust the brightness and contrast of the screen, press the MENU button whil[...]

Symbols The navigation system may have a feature that lets the driver view symbols on the navigation screen while using the rear vision camera. The Ultrasonic Rear Park Assist (URPA) system must not be disabled to use the caution symbols. If URPA has been disabled and the symbols have been turned on, the Rear Parking Assist Symbols Unavailable error message may display. See Ultrasonic Rear Parking Assist (URPA) on page 2-36 . The symbols appear when an object has been detected by the URPA system. The symbol may cover the object when viewing the navigation screen. To turn the symbols on or off: 1. Make sure that URPA has not been disabled. 2. Shift into P (Park). 3. Press the MENU hard key to[...]

The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance. The following illustration shows the field of view that the camera provides. A. View displayed by the camera. B. Corner of the rear bumper. When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: • The RVC is turned off. See “Turning the Rear Camera System On or Off” earlier in this section. • It is dark. • The sun or t[...]

• The back of the vehicle is in an accident, the position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your dealer/retailer. • There are extreme temperature changes. The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will flash. • A slow flash may indicate a loss of video signal, or no video signal present during the reverse cycle. • A fast flash may indicate that the display has been on for the maximum allowable time during a reverse cyc[...]

OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the first prepaid year, contact OnStar to select a monthly or annual subscription payment plan. If a payment plan is not selected, the OnStar system and all services, including airbag notification and emergency services, may be deactivated and no longer available. For more information visit onstar.com (U.S.) or onstar.ca (Canada), or press the OnStar button to speak with an advisor. Not all OnStar services ar[...]

OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days. Hands-Free Calling can also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit onstar.com or onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Turn-by-Turn N[...]

How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy. This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicle’s GPS location so they can provide services where it is located. OnStar service cannot work unless the[...]

Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference [...]

Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Eras[...]

2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later[...]

7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Progr[...]

accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds. 2.[...]

Storage Areas Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box. Cupholders There are two cupholders, with removable liners, located in front of the center console. There may be cupholders located in the second row seat armrest. To access, pull the armrest down. There are additional cupholders located on each side of the third row seat and in each door. There may be cupholders located at the rear of the center console. To access, pull the handle down. Instrument Panel Storage This vehicle has an instrument panel storage area located above the radio. To open the cover, press the button. Center Console Storage Pull up on the lever, located on the f[...]

Second Row Center Console For vehicles with a second row center console, open each area to access the storage compartment inside. To access the upper storage area, press the upper button (B) and lift up. To access the lower storage area, press the lower button (C) and lift up. The top of the console can be folded forward for increased storage area. Lift up on handle on the rear of the console (A) and pull forward. { CAUTION Never open more than one of the three latches at a time to help avoid personal injury and damage to the console. Notice: Slide the front console as far forward as it will go before folding the second row console forward to help prevent damage to the consoles. Features and[...]

Floor Mats If the floor mat has a snap retainer, a grommet in the driver side floor mat attaches to a hook on the floor of the vehicle to secure the floor mat. To remove the floor mat, pull the mat towards the rear of the vehicle until the grommet can be removed from the hook. If the floor mat has a knob retainer, a grommet in the floor mat attaches to a knob on the floor of the vehicle to secure the floor mat. To remove the floor mat, turn the knob till it is aligned with the slot in the floor mat grommet and pull the floor mat up. To reinstall, center the slot in the floor mat grommet with the knob on the floor and set the mat in place. Then turn the knob until it is perpendi[...]

Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Cover For vehicles with a cargo cover, it can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use. Cargo Tie Downs Four cargo tie-downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads. Cargo Management System This vehicle has a cargo management system located in the rear of the vehicle. To remove the cargo management [...]

Sunroof The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open. The switches to operate the front sunroof and rear sunshade are located on the headliner above the rearview mirror. The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof. See Ignition Positions on page 2-21 . Vent: From the closed position, press and hold the front of the driver side switch to vent the sunroof. Press and hold the rear of the driver side switch to close the sunroof. Express-open/Express-close: From the closed position, press and release the rear of the driver side switch to express-open the sunroof. Press and release the fr[...]

Instrument Panel Instrument Panel Overview Instrument Panel Overview .... .3-4 Hazard Warning Flashers ...... .3-5 Horn ................................... .3-5 Tilt and Telescopic Steering Wheel ............................... .3-6 Turn Signal/Multifunction Lever ................................ .3-6 Turn and Lane-Change Signals .............................. .3-6 Headlamp High/Low-Beam Changer ............................ .3-7 Flash-to-Pass ....................... .3-7 Windshield Wipers ................ .3-7 Windshield Washer ............... .3-8 Rear Window Wiper/Washer . . .3-9 Cruise Control ..................... .3-9 Exterior Lamps ................... .3-11 Delayed Headlamps ..........[...]

Cruise Control Light ............ .3-43 Highbeam On Light ............. .3-43 Tow/Haul Mode Light .......... .3-43 Fuel Gage ......................... .3-43 Driver Information Center (DIC) Driver Information Center (DIC) .................... .3-44 DIC Operation and Displays (With DIC Buttons) ............ .3-45 DIC Operation and Displays (Without DIC Buttons) ........ .3-51 DIC Compass .................... .3-54 DIC Warnings and Messages ........................ .3-56 DIC Vehicle Customization (With DIC Buttons) ............ .3-65 Audio System(s) Audio System(s) ................. .3-73 Setting the Clock ................ .3-74 Radio(s) ............................ .3-75 Using an MP3 (Radio wi[...]

✍ NOTES Instrument Panel 3-3[...]

Instrument Panel Overview 3-4 Instrument Panel[...]

The main components of the instrument panel are listed here: A. Turn Signal/Multifunction Lever on page 3-6 . Windshield Wipers on page 3-7 . B. Instrument Panel Cluster on page 3-31 . C. Audio Steering Wheel Controls on page 3-125 . D. Instrument Panel Storage on page 2-52 . E. Audio System(s) on page 3-73 or Navigation/Radio System on page 3-103 (If Equipped). F. Outlet Adjustment on page 3-27 . G. Exterior Lamps on page 3-11 . Fog Lamps on page 3-13 (If Equipped). H. Dome Lamp Override on page 3-14 . Instrument Panel Brightness on page 3-13 . Heated Windshield Washer Button. See Windshield Washer on page 3-8 . I. Cruise Control on page 3-9 . J. Tilt and Telescopic Steering Wheel on page 3[...]

Tilt and Telescopic Steering Wheel The steering wheel can be adjusted. The adjustment lever is located on the left side of the steering column. Pull the lever down to move the steering wheel up or down and in or out. Pull the lever up to lock the steering wheel in place. Do not adjust the steering wheel while driving. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals 3 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield Washer Flash-to-Pass Feature. Information for these features is on the pages following. For information on the headlamps, see Exterior Lamps on page 3-11 . Turn and Lane[...]

Turn Signal On Chime If either one of the turn signals are left on and the vehicle has been driven more than 3/4 mile (1.2 km), a chime will sound. Headlamp High/ Low-Beam Changer 23 Headlamp High/Low Beam Changer: Push the turn signal/ multifunction lever away from you to turn the high beams on. Pull the lever towards you to return to low beams. This indicator light turns on in the instrument panel cluster when the high beam headlamps are on. Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low-beam position, pull the turn signal lever toward you to momentarily switch to high-beams. Release the lever to turn the high[...]

Windshield Washer J (Washer Fluid): Press the button located at the end of the turn signal/multifunction lever, to spray washer fluid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACC/ACCESSORY or ON/RUN for this to work. See Windshield Washer Fluid on page 5-24 Windshield Washer Fluid. { CAUTION In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. WASHER FLUID LOW ADD FLUID is displayed on the Driver Information Center (DIC) when the washer fluid is low. See DIC Warnings and Messages on page 3-56 . Heated W[...]

Rear Window Wiper/Washer The rear wiper and rear wash button is located on the instrument panel below the climate control system. Z (Rear Wiper): Press to turn the rear wiper on and off. The wiper speed cannot be changed. Y (Wash): Press to spray washer fluid on the rear window. The window wiper will also come on. Release the button when enough fluid has been sprayed on the window. The rear wiper will run a few more cycles after it is released. If the rear wiper function was already on, prior to pressing the wash button, it stays on until the wiper button is pressed again. The rear window washer uses the same fluid that is in the windshield washer reservoir. See Windshield Washer Fluid on[...]

Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed. { CAUTION If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the I button. 2. Get up to the speed desired. 3. Press and release the SET– button located on the steering wheel. 4. Take your foot off the accelerator. Resuming a Set[...]

Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. When the brakes are applied the cruise control is disengaged. Ending Cruise Control There are three ways to end cruise control: • Step lightly on the brake pedal. • Press the [ button. • Press the T button. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Exterior L[...]

2 (Headlamps): Turns on the headlamps together with the following lamps listed below. A warning chime sounds if the driver door is opened when the ignition switch is off and the headlamps are on. • Parking Lamps • Taillamps • License Plate Lamps • Instrument Panel Lights # (Fog Lamps) (If Equipped): Turns on the fog lamps. See Fog Lamps on page 3-13 . Delayed Headlamps Delayed headlamps provide a period of exterior lighting as you leave the area around your vehicle. This feature is activated when the headlamps are on due to the automatic headlamps control feature, and when the ignition is turned off. The headlamps remain on until the exterior lamps control is moved to the parking lam[...]

When the DRL are on, the regular headlamps, taillamps, sidemarker, and other lamps are not on. The instrument panel and cluster are also not on. The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps go off and the DRL come on. The regular headlamp system should be turned on when needed. Do not cover the light sensor on top of the instrument panel because it works with the DRL. Fog Lamps # (Fog Lamps): For vehicles with fog lamps, the button is located on the exterior lamps control. The exterior lamps control is locate[...]

Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easier when entering and exiting the vehicle. The lamps can also be turned on manually by fully turning the instrument panel brightness control clockwise. The reading lamps, located on the headliner above the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed. Dome Lamps The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on and off by turning the instrument panel brightness control clockwise to the farthest position. Dome Lamp Override The dome lamp ov[...]

Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs: • The ignition is in ON/RUN. • The doors are locked. • An illumination period of about 25 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period is canceled and the interior lamps remain on. Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. T[...]

When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occur[...]

Accessory Power Outlet(s) Accessory power outlets let you plug in auxiliary electrical equipment, such as a cellular phone. The vehicle may have four accessory power outlets. They are located on the instrument panel below the climate controls, under the front center console cupholders, at the rear of the center console, and in the rear cargo area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. Certain electrical acce[...]

Power Outlet 115 Volt Alternating Current For vehicles with this power outlet, it can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located on the rear of the center console. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected. The indicator light does not come on when the ignition is in LOCK/OFF or if no equipment is plugged into the outlet. If equipment is connected using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and [...]

Climate Controls Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. Temperature Control C. Air Delivery Mode Control D. Air Conditioning E. REAR (Rear Climate Control) F. Recirculation G. Rear Window Defogger 9 (Off): Turn the fan control all the way counterclockwise to turn the front climate control system off. 9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system. Air Delivery Mode Control: Turn clockwise or counterclockwise to change the current[...]

6 (Floor): Air is directed to the floor outlets, with some of the air directed to the windshield, side window, and second row floor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected while in floor mode. - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning unless the outside temperature is less than 40°F (4°C). Recirculation cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0 (Defrost): This mode quickly clears the[...]

The air conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re-selected when the engine is turned on again. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. The recirculation mode cannot be used with floor, defrost, or defogging modes. If recirculation is selected in [...]

Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. AUTO C. Defrost D. Recirculation E. REAR (Rear Climate Control) F. Air Delivery Mode Control G. Driver Side Temperature Control H. Display I. Power (On/Off) J. Rear Window Defogger K. Air Conditioning L. PASS (Passenger) M. Passenger Side Temperature Control Display Function Each time the temperature, mode, or fan control buttons are pressed, the climate control display shows that function along with the inside temperature setting. The outside temperature is displayed on the instrument panel cluster. O (On/Off): Press to turn the climate control sys[...]

Automatic Operation AUTO (Automatic): The system automatically controls the inside temperature, the air delivery, and the fan speed. To use automatic mode: 1. Press the AUTO button. When AUTO is selected, the current temperature(s) selected and AUTO is shown on the display. The current air delivery mode and fan speed also appear for approximately five seconds. When AUTO is selected, the air conditioning and air inlet are automatically controlled. The air conditioning runs when the outside temperature is over 40°F (4°C). The system is automatically set to outside air, unless it is hot outside and then the air inlet changes to recirculation mode to help quickly cool the vehicle. The recircu[...]

PASS (Passenger): Press to set the passenger temperature to match the driver temperature setting. The PASS indicator will turn off. When the passenger temperature setting is different than the driver setting, the PASS indicator comes on. Manual Operation The air delivery mode or fan speed can be manually adjusted. D / C (Fan Control): Press to increase or decrease the fan speed. Pressing D or C while in automatic control places the fan speed under manual control. The air delivery mode remains in automatic control. The fan setting still displays, but the word AUTO no longer displays, and the AUTO button indicator light turns off. H / G (Air Delivery Mode Control): Press to change the directio[...]

- (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is less than 40°F (4°C). Do not drive the vehicle until all the windows are clear. 0 (Defrost): Press to turn the defrost on or off. This mode quickly clears the windshield of fog or frost. Air is directed to the windshield, side window, and floor vents. In this mode, outside air is pulled inside the vehicle. The air conditioning system runs automatically in this setting, unless the outside temperature is less than 40°F (4?[...]

This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. The recirculation mode cannot be used with floor, defog, or defrosting modes. If recirculation is selected in these modes, the indicator flashes three times and turns off. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows can fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. REAR: Press to turn the rear heating and air conditioning on or off. See Rear Air Conditioning and Heating System on page 3-28 or [...]

The interior temperature sensor located on the instrument panel to the right of the steering column, measures the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature. The climate control system uses the information from these sensors to maintain comfort settings by adjusting the temperature, fan speed, and the air delivery mode. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode [...]

Rear Air Conditioning and Heating System A. Fan Control B. Temperature Control C. Air Delivery Mode Control For vehicles with the rear climate control system, the controls are located on the rear of the center console. The system can also be controlled with the front controls. Press the REAR button on the front climate control system to turn the rear climate control system on or off. An indicator comes on when the rear system is on. The system also turns on if any of the rear controls are adjusted. Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Independent Mode: This mode directs rear seating airflow according [...]

Rear Air Conditioning and Heating System and Electronic Climate Controls A. Fan Control B. Air Delivery Mode Control C. Temperature Control For vehicles with the rear climate control system, the controls are located on the rear of the center console. Press the REAR button on the front climate control system to turn the rear climate control system on or off. The system also turns on if any of the rear controls, except for the C are pressed. An indicator comes on when the rear system is on. The system can also be turned off, by pressing and holding the C button. Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Indep[...]

N (Air Delivery Mode Control): Press to manually change the direction of the airflow. Repeatedly press the button until the desired mode appears on the display. H (Vent): Air is directed through the overhead outlets. ) (Bi-Level): Air is directed through the rear floor outlets, as well as the overhead outlets. 6 (Floor): Air is directed through the floor outlets. The rear system floor outlets are located under the third row seats. Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could prevent injury. Warning lights[...]

Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel is being used, and many other things needed to drive safely and economically. United States Uplevel version shown, Canada similar Instrument Panel 3-31[...]

Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles or kilometers. This vehicle has a tamper-resistant odometer. If the vehicle needs a new odometer installed, the new one is set to the mileage total of the old odometer. If this is not possible, it is set at zero and a label is put on the driver’s door to show the old mileage reading when the new odometer was installed. If the mileage is unknown, the label should then indicate “previous mileage unknown”. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). [...]

Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-46 . This light will come on and stay on for several seconds when the vehicle is started. Then the light should go out. If the airbag readiness light stays on after the vehicle has been started or comes on when while driving, the airbag system may not work properly. Have the vehicle serviced right away. { CAUTION If the airbag readiness light stays on after the vehicle is started or comes on while driving, it m[...]

Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing sy[...]

When this light comes on, the Driver Information Center (DIC) also displays the SERVICE BATTERY CHARGING SYSTEM message. See DIC Warnings and Messages on page 3-56 for more information. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner. Voltmeter Gage When the engine is not running, but the ignition is on, this gage displays the battery voltage in DC volts. When the engine is running, the gage shows the condition of the charging system. The gage can transition from a higher to lower or a lower to higher reading. This is normal. Readings between the low and high warning zones indicate the normal operating range. Th[...]

Brake System Warning Light This vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away. { CAUTION The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. This light should come on briefly when the ignition key is turned to ON/RUN. If[...]

Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If[...]

This light flashes when the StabiliTrak system is active. If the StabiliTrak system warning light comes on and stays on for an extended period of time when the system is turned on, the vehicle needs service. See StabiliTrak ® System on page 4-5 for more information. Engine Coolant Temperature Warning Light The engine coolant temperature warning light comes on when the engine has overheated. If this happens pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-22 for more information. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 5-22 . The vehicle’s engine could be[...]

Tire Pressure Light If the vehicle has a tire pressure monitoring system, the tire pressure light provides information about tire pressures and the Tire Pressure Monitoring System. The light should come on briefly as the engine is started. If it does not, have the vehicle serviced by your dealer/ retailer. When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See DIC Warnings and Messages on page 3-56 for more information. Stop and check the tires as soon as it is safe to do so. If underinflated, inflate to the proper pressure. See Tires on page 5-[...]

If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Mo[...]

Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by checking the following items: • Make sure the fuel cap is fully installed. See Filling the Tank on page 5-7 . The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. • If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when t[...]

Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on. • The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered [...]

Security Light This light flashes when the security system is activated. For more information, see Theft-Deterrent Systems on page 2-16 . Cruise Control Light This light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 3-9 for more information. Highbeam On Light The highbeam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-7 for more information. Tow/Haul Mode Light This light comes on when the Tow/Haul mode has been activated. For more information, see Tow/Haul Mode on page 2-26 . Fuel Gage When the ignition is on, the fuel gage indicates about how much fu[...]

An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these show a problem with the fuel gage: • At the gas station, the gas pump shuts off before the gage reads full. • It takes a little more or less fuel to fill up than the gage indicated. For example, the gage might have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to fill the tank. • The gage moves a little while turning a corner or speeding up. • The gage does not go back to empty when the ignition is turned off. Driver Information Center (DIC) Your vehicle has a Driver Information[...]

DIC Operation and Displays (With DIC Buttons) If your vehicle has DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel. See Instrument Panel Overview on page 3-4 for more information. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The DIC also allows some features to be customized. See DIC Vehicle Customization (With DIC Buttons) on page 3-65 for more information. If your vehicle has DIC buttons, you can also use the trip odometer reset stem to view the odometer and trip odometers. DIC Buttons[...]

Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items: OIL LIFE Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 3-56 . You should change the oil as soon as you[...]

FRONT TIRES or REAR TIRES On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##. If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a specific tire will appear in the display. See Inflation - Tire Pressure on page 5-42 and DIC Warnings and Messages on page 3-56 for[...]

COMPASS ZONE SETTING This display will be available if the vehicle has a compass. See DIC Compass on page 3-54 for more information. COMPASS RECALIBRATION This display will be available if the vehicle has a compass. See DIC Compass on page 3-54 for more information. Blank Display This display shows no information. Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items: ODOMETER Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see[...]

The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retro-active reset feature, press and hold the set/reset button for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 5 miles (8 km) before it is started again, and then the retro-active[...]

FUEL ECONOMY Press the trip/fuel button until FUEL ECONOMY displays. The FUEL ECONOMY display shows an estimate of the vehicle fuel economy under a given driving condition at a specific moment. For example, if the vehicle is accelerating and achieving low fuel eff iciency this display will show fewer bars, but if the vehicle is cruising on a flat freeway and getting high fuel eff iciency, the display will show more bars. Fuel economy cannot be reset. TIMER Press the trip/fuel button until TIMER displays. This display can be used as a timer. To start the timer, press the set/reset button while TIMER is displayed. The display will show the amount of time that has passed since the timer was l[...]

DIC Operation and Displays (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster. Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages. The DIC displays trip and vehicle system information, and warning messages if a system problem is detected. If your vehicle does not have DIC buttons, you can use the trip odometer reset stem to view the following displays: odometer, trip odometers, oil life, park assist menu for vehicles with the Ultrasonic Rear Parking A[...]

To use the retro-active reset feature, press and hold the trip odometer reset stem for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 5 miles (8 km) before it is started again, and then the retro-active reset feature is activated, the display will show 5 miles (8 km). As the vehicle begins moving, the display will then increase to 5.1 miles (8.2 km), 5.2 miles (8.4 km), etc. If the retro-active reset feature is activated after the vehicle is started, but bef[...]

PARK ASSIST To access this display, the vehicle must be in P (Park). If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, press the trip odometer reset stem until PARK ASSIST displays. This display allows the system to be turned on or off. Once in this display, press and hold the trip odometer reset stem to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. The URPA system automatically turns back on after each vehicle start. When the URPA system is turned off and the vehicle is shifted out of P (Park), the DIC will display the PARK ASSIST OFF message as a reminder that the system has been turned off. S[...]

DISPLAY LANGUAGE To access this display, the vehicle must be in P (Park). This display allows you to select the language in which the DIC messages will appear. To select a language: 1. Press the trip odometer reset stem until DISPLAY LANGUAGE displays. 2. Continue to press and hold the trip odometer reset stem to scroll through all of the available languages. The available languages are ENGLISH (default), FRANCAIS (French), ESPANOL (Spanish), and NO CHANGE. 3. Once the desired language is displayed, release the trip odometer reset stem to set your choice. DIC Compass Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leavin[...]

3. Press the set/reset button to scroll through and select the appropriate variance zone. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following. Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible. If CAL should ever appear in the DIC display, the co[...]

DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons on the instrument panel or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the displ[...]

BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping below expected levels. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off all unnecessary accessories to allow the battery to recharge. The normal battery voltage range is 11.5 to 15.5 volts. CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System [...]

DRIVER DOOR OPEN This message displays and a chime sounds if the driver door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gage on page 3-38 . To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehi[...]

ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 5-22 for further information. This message also displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehi[...]

LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. LIFTGATE OPEN This message displays and a chime sounds if the liftgate is open while the ignition is in ON/RUN. Turn off the vehicle and check the liftgate. Restart the vehicle and check for the message on the DIC display. OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the D[...]

REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle” under Remote Keyless Entry (RKE) System Operation on page 2-4 and DIC Operation and Displays (With DIC Buttons) on page 3-45 or DIC Operation and Displays (Without DIC Buttons) on page 3-51 for more information. REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-4 . RIGHT REAR DOOR OPEN This message displays and a [...]

SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 3-34 . Driving with this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer/retailer. SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 3-36 . If this message appears, stop as soon as possible and turn off the vehicle. Restar[...]

SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-39 . Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-45 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust yo[...]

TIGHTEN GAS CAP This message may display along with the check engine light on the instrument panel cluster if the vehicle’s fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 3-39 . Reinstall the fuel cap fully. See Filling the Tank on page 5-7 . The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off. TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. [...]

TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 3/4 of a mile (1.2 km). Move the turn signal/multifunction lever to the off position. WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer fluid reservoir as soon as possible. See Engine Compartment Overview on page 5-10 for the location of the windshield washer fluid reservoir. Also, see Windshield Washer Fluid on page 5-24 for more information. DIC Vehicle Customization (With DIC Buttons) Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only b[...]

Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle: DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English. Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English. DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/res[...]

To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-9 for more information. Press the customization button until AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER AT KEY OUT: Only the driver’s door[...]

HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. HORN & LIGHTS (default): The exterior lamps will flash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback whe[...]

Then press the customization button to scroll through the following settings: OFF: There will be no delayed locking of the vehicle’s doors. ON (default): The doors will not lock until five seconds after the last door or the liftgate is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DI[...]

The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-4 for more information. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following sett[...]

EASY EXIT SEAT If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat and Mirrors on page 1-6 for more information. Press the customization button until EASY EXIT SEAT appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No automatic seat exit recall will occur. ON: The driver’s seat will move back when the key is removed from the ignition. The automatic easy exit seat movement will only occur one time after the key is removed from the ignition. If the automatic movement has [...]

REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-6 for more information. Press the customization button until REMOTE START appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. NO CHANGE: No change will be made to this feature. The current setting will r[...]

Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: • The vehicle is shifted out of P (Park). • The vehicle is no longer in ON/RUN. • The trip/fuel or vehicle information DIC buttons are pressed. • The end of the feature settings menu is reached and exited. • A 40 second time period has elapsed with no selection made. Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driv[...]

Setting the Clock To adjust the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN, then press O , to turn the radio on. 2. Press G to display HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year). 3. Press the pushbutton located under any one of the labels to be changed. 4. To increase the time or date, do one of the following: • Press the pushbutton below the selected label. • Press ¨ SEEK. • Press FWD. • Turn f clockwise. 5. To decrease the time or date, do one of the following: • Press © SEEK. • Press s REV. • Turn f counter-clockwise. To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/yea[...]

Radio(s) Radio with CD Instrument Panel 3-75[...]

The vehicle may have one of these radios as its audio system. Radios with CD and DVD Radios with CD and DVD have a Bose ® Surround Sound System. Some of its features are explained later in this section under, “Adjusting the Speakers (Balance/Fade)”. If the vehicle has a Rear Seat Entertainment (RSE) system, it has a CD/DVD radio. See Rear Seat Entertainment (RSE) System on page 3-114 for more information on the vehicle’s RSE system. The DVD player is the top slot on the radio faceplate. The player is capable of reading the DTS programmed DVD Audio or DVD Video media. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. Manufactured under license from[...]

Playing the Radio O (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. For vehicles with a Rear Entertainment System (RSE), press and hold for more than two seconds to turn off the entire radio and RSE system and to start the parental control feature. Parental control prevents the rear seat occupant from operating the Rear Seat Audio (RSA) system or remote control. A lock symbol displays next to the clock display while the parental control feature is being used. The feature remains on until O is pressed and held for more than two seconds, or the driver turns the ignition off and exits the vehicle. 4 (Information): Press to switch the display between[...]

Finding a Station BAND: Press to switch between AM, FM, or XM. The selection displays. f (Tune): Turn to select radio stations. © SEEK ¨ : Press to go to the previous or to the next station and stay there. To scan stations, press and hold © or ¨ until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band. Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is in P (Park). Tune to favorite stations using the presets, favorites button, and steerin[...]

To setup the number of favorites pages: 1. Press MENU to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 4. Press FAV, or let the menu time out, to return to the original main radio screen showing the radio station frequency labels and to begin the process of programming favorites for the chosen amount of numbered pages. Auto Text (Satellite Radio Service, CD, MP3, and WMA features): If additional information is available for the current song being played, Auto Text will automatically page/scroll the information every five seconds above [...]

To quickly adjust bass, midrange, or treble to the middle position, press the pushbutton positioned under the BASS, MID, or TREB label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all tone and speaker controls to the middle position, press f for more than two seconds until a beep sounds. EQ (Equalization): Press to choose bass and treble equalization settings designed for different types of music. The choices are pop, rock, country, talk, jazz, and classical. Selecting MANUAL or changing bass or treble, returns the EQ to the manual bass and treble settings. Unique EQ settings can be saved for each source. If the radio has a Bose ® [...]

Finding a Category (CAT) Station CAT (Category): The CAT button is used to find XM™ stations when the radio is in the XM mode. To find XM channels within a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category labels. 3. Continue pressing CAT until the desired category name displays. • Radios with CD and DVD can also navigate the category list by pressing s REV or FWD. 4. Press either of the two buttons below the desired category label to immediately tune to the first XM station associated with that category. 5. To go to the next or previous XM station within the selected category, do one of the following: • Turn f . • Press the bu[...]

Radio Messages Calibration Error: The audio system has been calibrated for the vehicle from the factory. If Calibration Error displays, it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer/retailer for service. Locked: This message displays when the THEFTLOCK ® system has locked up the radio. Take the vehicle to your dealer/retailer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and[...]

See Rear Seat Audio (RSA) on page 3-123 for more information. The DVD/CD decks, (upper slot is the DVD deck and the lower slot is the CD deck) of the radio are compatible with most audio CDs, CD-R, CD-RW, and MP3/WMAs. When a CD is inserted, the text label DVD or CD symbol displays on the left side of the radio display. As each new track starts to play, the track number displays. Care of CDs and DVDs If playing a CD-R, the sound quality can be reduced due to CD-R or CD-RW quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R or CD-RW has been handled. Handle them carefully. Store CD-R(s) or CD-RW(s) in their original cases or other protective[...]

Z EJECT or CD (Eject): Press and release to eject the disc that is currently playing. A CD ejecting from a radio with CD and DVD, ejects from the bottom slot. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The disc can be removed. If the disc is not removed, after several seconds, the disc automatically pulls back into the player. Z DVD (Eject): Press and release to eject the disc that is currently playing in the top slot. A beep sounds and Ejecting Disc displays. If loading and reading of a disc cannot be completed, and the disc fails to eject, press and hold Z DVD for more than five seconds to force the disc to eject. f (Tune): Turn to select tra[...]

CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary. • When a CD is in the player the CD icon and a message showing the disc and/or track number displays. • If an auxiliary input device is not connected, “No Input Device Found” displays. DVD/CD AUX (Auxiliary): Press to select between DVD, CD, or Auxiliary. • If an auxiliary input device is not connected, “No Aux Input Device” displays. • When a disc is in either slot, the DVD/CD text label and a message showing the track or chapter number displays. • If an auxiliary input device is not connected, and a disc is in both the DVD slot and the CD slot the DVD/CD AUX button only cycles between the two sources and doe[...]

See “Using the Auxiliary Input Jack(s)” later in this section, or “Audio/Video (A/V) Jacks” under, Rear Seat Entertainment (RSE) System on page 3-114 for more information. In some vehicles, depending on audio options, the rear speakers can be muted when the RSA power is turned on. See Rear Seat Audio (RSA) on page 3-123 for more information. Playing an MP3/WMA CD-R or CD-RW Disc The radio has the capability of playing an MP3/WMA CD-R or CD-RW disc. For more information on how to play an MP3/WMA CD-R or CD-RW disc, see “Using an MP3” in the index. CD Messages CHECK DISC: Radios with a Single CD player display CHECK DISC and/or ejects the CD if an error occurs. Radios with a CD and[...]

Using the DVD Player The DVD player can be controlled by the buttons on the remote control, the RSA system, or by the buttons on the radio faceplate. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 and Rear Seat Audio (RSA) on page 3-123 for more information. The DVD player is only compatible with DVDs of the appropriate region code that is printed on the jacket of most DVDs. The DVD slot of the radio is compatible with most audio CDs, CD-R, CD-RW, DVD-Video, DVD-Audio, DVD-R/RW, DVD+R/ RW media along with MP3 and WMA formats. If an error message displays on the video screen or the radio, see “DVD Display Error Messages” under, Rear Seat Entertainment ([...]

DVD-V (Video) Display Buttons Once a DVD-V is inserted, the radio display menu shows several icons. Press the pushbuttons located under any desired icon during DVD playback. See the icon list below for more information. The rear seat passenger can navigate the DVD-V menus and controls through the remote control. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 for more information. The Video Screen automatically turns on when the DVD-V is inserted into the DVD slot. r / j (Play/Pause): Press either the play or pause icon displayed on the radio system, to toggle between pausing or restarting playback of a DVD. • If the forward arrow is showing on display, t[...]

DVD-A (Audio) Display Buttons Once a DVD-A is inserted, the radio display menu shows several icons. Press the pushbuttons located under any desired icon during DVD playback. See the icon list below for more information. The rear seat operator can navigate the DVD-A menus and controls through the remote control. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 for more information. The Video Screen does not automatically power on when the DVD-A is inserted into the DVD slot. It must be manually turned on by the rear seat occupant through the remote control power button. r / j (Play/Pause): Press either the play or pause icon displayed on the radio system, to [...]

Stopping and Resuming Playback To stop playing a DVD without turning off the system, do one of the following: • Press c on the remote control. • Press the pushbutton located under the stop or the play/pause icons displayed on the radio. • If the radio head is sourced to something other than DVD-V, press the DVD/CD AUX button to make DVD-V the active source. To resume DVD playback, do one of the following: • Press r / j on the remote control. • Press the pushbutton located under the play/pause icon displayed on the radio. The DVD should resume play from where it last stopped if the disc has not been ejected and the stop button has not been pressed twice on the remote control. If the[...]

Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug a headphone set into the front auxiliary input jack. Connect an auxiliary input device such as an iPod, laptop computer, MP3 player, CD player, or cassette tape player, etc. to the auxiliary input jack for use as another source for audio listening. Drivers are encouraged to set up any auxiliary device while the vehicle is in P (Park). See Defensive Driving on page 4-2 for more information on driver distraction. To use an auxiliary input device, connect a 3.5 mm (1/8 inch) cable to the radio’s front auxiliary input jack. O (Po[...]

If a disc is inserted into top DVD slot, the rear seat operator can turn on the video screen and use the remote control to only navigate the CD tracks through the remote control. See “Using the Auxiliary Input Jack(s)” later in this section, or “Audio/Video (A/V) Jacks” under, Rear Seat Entertainment (RSE) System on page 3-114 for more information. Using an MP3 (Radio with CD) MP3/WMA CD-R or CD-RW Disc The radio plays MP3/WMA files that were recorded on a CD-R or CD-RW disc. The files can be recorded with the following fixed bit rates: 32 kbps, 40 kbps, 56 kbps, 64 kbps, 80 kbps, 96 kbps, 112 kbps, 128 kbps, 160 kbps, 192 kbps, 224 kbps, 256 kbps, and 320 kbps or a variable bit r[...]

• The CD player is able to read and play a maximum of 50 folders, 15 playlists, and a combined total of 512 folders and files. • Create a folder structure that makes it easy to find songs while driving. Organize songs by albums using one folder for each album. Each folder or album should contain 18 songs or less. • Avoid subfolders. The system can support up to eight subfolders deep, however, keep the total number of folders to a minimum in order to reduce the complexity and confusion in trying to locate a particular folder during playback. • Make sure playlists have a .mp3 or .wpl extension (other file extensions might not work). • Minimize the length of the file, folder, or p[...]

Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that contains only folders/subfolders and no compressed files directly beneath them, the player advances to the next folder in the file structure that contains compressed audio files. The empty folder does not display. No Folder When the CD-R or CD-RW disc contains only compressed files, the files are located under the root folder. The next and previous folder function does not display on a CD-R or CD-RW disc that was recorded without folders or playlists. When the CD-R or CD-RW disc contains only playlists and compressed audio files, but no folders, all files are located under the root f[...]

Playing an MP3/WMA Insert a CD-R or CD-RW disc partway into the slot label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. Z EJECT: Press to eject the disc. f (Tune): Turn to select MP3/WMA files on the CD-R or CD-RW currently playing. © SEEK ¨ : Press the left SEEK arrow to go to the start of the current MP3/WMA file, if more than ten seconds have played. Press the right SEEK arrow to go to the next MP3/WMA file. If either SEEK arrow is held or pressed multiple times, the player continues moving backward or forward through MP3/WMA files on the CD. S c (Previous Folder): Press the pushbutton positioned under the Folder label to go to the first track in the[...]

h (Music Navigator): Use the music navigator feature to play MP3/WMA files on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator label. The player scans the disc to sort the files by artist and album ID3 tag information. It could take several minutes to scan the disc depending on the number of MP3/WMA files recorded to the CD-R or CD-RW disc. The radio can begin playing while it is scanning the disc in the background. When the scan is finished, the CD-R or CD-RW begins playing again. Once the disc has scanned, the player defaults to playing MP3/WMA files in order by artist. The current artist playing is shown on the second line of the d[...]

MP3/WMA Format To create an MP3/WMA disc on a personal computer: • Make sure the MP3/WMA files are recorded on a CD-R or CD-RW disc. • Do not mix standard audio and MP3/WMA files on one disc. • The CD player (lower slot) is able to read and play a maximum combination of 512 files and folders. The DVD player (upper slot) is able to read 255 folders, 15 playlists and 40 sessions. • Create a folder structure that makes it easy to find songs while driving. Organize songs by albums using one folder for each album. Each folder or album should contain 18 songs or less. • Avoid subfolders. The system can support up to eight subfolders deep, however, keep the total number of folders to [...]

No Folder When the CD-R or CD-RW disc contains only compressed files, the files are located under the root folder. The next and previous folder function does not function on a CD-R or CD-RW that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT. When the CD-R or CD-RW disc contains only playlists and compressed audio files, but no folders, all files are located under the root folder. The folder down and the folder up buttons search playlists (Px) first and then goes to the root folder. When the radio displays the name of the folder the radio displays ROOT. Order of Play Tracks recorded to the CD-R or CD-RW disc are played in the fo[...]

Playing an MP3/WMA (In Either the DVD or CD Slot) Insert a CD-R or CD-RW disc partway into either the top or bottom slot, label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. Depending on the format of the disc, a softkey menu appears and allows navigation of the disc. The menu reads left to right as RDM (Randomize song play order), a Folder icon with left and right arrows (to move up or down through available folders), a PL tag if the disc has a Playlist available, and a Music Navigator tag. If a Playlist tag is shown, toggling this key brings up a Folder softkey only or the menu as previously described. If the ignition or radio is turned off with a CD-R or CD-[...]

© SEEK ¨ : Press the left SEEK arrow to go to the start of the current MP3/WMA file, if more than five seconds have played. If less than five seconds have played, the previous MP3/WMA file plays. Press the right SEEK arrow to go to the next MP3/WMA file. If either SEEK arrow is held, or pressed multiple times, the player continues moving backward or forward through the MP3/WMA files on the CD. S c (Previous Folder): Press the pushbutton positioned under the Folder label to go to the first track in the previous folder. c T (Next Folder): Press the pushbutton positioned under the Folder label to go to the first track in the next folder. s REV (Reverse): Press and hold this button to [...]

Once the disc has been scanned, the player defaults to playing MP3/WMA files in order by artist. The current artist playing is shown on the second line of the display between the arrows. To listen to MP3/WMA files by another artist, press the pushbutton located below either arrow button. The disc goes to the next or previous artist in alphabetical order. Continue pressing either button until the desired artist is displayed. To change from playback by artist to playback by album, press the pushbutton located below the Sort By label. From the sort screen, push one of the buttons below the album button. Press the pushbutton below the back label to return to the main music navigator screen. No[...]

XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. Channel Off Air: This channel is not currently in service. Tune in t[...]

Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Bluetooth ® Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The system can be[...]

Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-125 for more information. b g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start speech recognition. c x (Phone On Hook): Press to end a call, reject a call, or to cancel an operation. Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnSt[...]

5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “<Phone name> has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices. If a phone is connecte[...]

Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: • Store • Digit Store • Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please” followed by a tone. 3. Say the complete phone number to be stored at once with no pauses. • If the system recognizes the number it responds with “OK, Storin[...]

Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Store”. The system responds with “Please say the first digit to store” followed by a tone. 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. • To hear all of the numbers recognized by the system, say “Verify” at any t[...]

Using the Delete Command The delete command allows specific name tags to be deleted. To use the delete command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag” followed by a tone. 3. Say the name tag to be deleted. The system responds with “Would you like to delete, <name tag>? Please say yes or no”. • If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting <name tag>, returning to the main menu.” • If the name tag is incorrect, say “No”. The system responds with “No. OK, let’s try[...]

3. Say the entire number without pausing. • If the system recognizes the number, it responds with “OK, Dialing” and dials the number. • If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number to be re-entered. Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Dial”. The system responds with “Digit dial using <phone name>, please say the first digit to dial” followed [...]

Using the Call Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using <phone name>. Please say the name tag” followed by a tone. 3. Say the name tag of the person to call. • If the system clearly recognizes the name tag it responds with “OK, calling, <name tag>” and dials the number. • If the system is unsure it recognizes the right name tag, it confirms the name tag followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, calling, <name tag>” and dials the number. If the name tag is not correct, say “No”. The syst[...]

Three-Way Calling Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press b g . The system responds with “Ready” followed by a tone. 2. Say “Three-way call”. The system responds with “Three-way call, please say dial or call”. 3. Use the dial or call command to dial the number of the third party to be called. 4. Once the call is connected, press b g to link all the callers together. Ending a Call Press c x to end a call. Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press b g . The system[...]

Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Voice”. The system responds with “OK, accessing <phone name>”. • The cell phone’s normal prompt messages will go through its cycle according to the phone’s operating instructions. Dual Tone Multi-Frequency (DTMF) To[...]

Sending a Stored Name Tag During a Call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. 3. Say the name tag to send. • If the system clearly recognizes the name tag it responds with “OK, Sending <name tag>” and the dial tones are sent and the call continues. • If the system is not sure it recognized the name tag properly, it responds “Dial <name tag>, Please say yes or no?” followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, Sending <name tag>” and the dial tones are sent and the call con[...]

Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle’s audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control. See Radio(s) on page 3-75 for more information on the vehicle’s audio/DVD system. Before Driving The RSE is designed for rear seat passengers only. The driver cannot safely view the video screen while driving and should not try to do so. In severe or extreme weather conditions the RSE system might or might not work until the temperature is within the ope[...]

The wireless headphones have an On/Off button, channel 1/2 switch, and a volume control. Switch the headphones to Off when not in use. Push the power button to turn on the headphones. An indicator light located on the headphones comes on. If the light does not come on, the batteries might need to be replaced. Intermittent sound or static on the headphones can also be an indication of weak batteries. See “Battery Replacement” later in this section for more information. The headphones automatically turn off after four hours of continuous use. To adjust the volume on the headphones, use the volume control located on the right side. Infrared transmitters are located at the rear of the RSE ov[...]

Battery Replacement To change the batteries on the headphones: 1. Turn the screw to loosen the battery door located on the left side of the headphones. Slide the battery door open. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment. 3. Replace the battery door and tighten the door screw. If the headphones are to be stored for a long period of time, remove the batteries and keep them in a cool, dry place. Audio/Video (A/V) Jacks The A/V jacks, located on the rear of the floor console, allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game un[...]

How to Change the RSE Video Screen Settings The screen display mode (normal, full, and zoom), screen brightness, and setup menu language can be changed from the on screen setup menu by using the remote control. To change a setting: 1. Press z . 2. Use n , q , p , o and r to navigate and use the setup menu. 3. Press z again to remove the setup menu from the screen. Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following sources: • Wireless Headphones • Vehicle Speakers • Vehicle wired headphone jacks on the rear seat audio system, if the vehicle has this feature. The RSE system always transmits the audio signal to the wireless headphones, if there i[...]

Remote Control To use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control. If the remote control does not seem to be working, the batteries might need to be replaced. See “Battery Replacement” later in this section. Objects blocking the line of sight could also affect the function of the remote control. If a CD or DVD is in the Radio DVD slot, the remote control O button can be used to turn on the video screen display and start the disc. The radio can also turn on the video screen display. See Ra[...]

O (Power): Press to turn the video screen on and off. P (Illumination): Press to turn the remote control backlight on. The backlight automatically times out after seven to ten seconds if no other button is pressed while the backlight is on. v (Title): Press to return the DVD to the main menu of the DVD. This function could vary for each disc. y (Main Menu): Press to access the DVD menu. The DVD menu is different on every DVD. Use the navigation arrows to move the cursor around the DVD menu. After making a selection press the enter button. This button only operates when using a DVD. n , q , p , o (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu. r (Enter): Press to s[...]

r (Fast Reverse): Press to quickly reverse the DVD or CD. To stop fast reversing a DVD video, press s . To stop fast reversing a DVD audio or CD, release r . This button might not work when the DVD is playing the copyright information or the previews. [ (Fast Forward): Press to fast forward the DVD or CD. To stop fast forwarding a DVD video, press s . To stop fast forwarding a DVD audio or CD, release [ . This button might not work when the DVD is playing the copyright information or the previews. e (Audio): Press to change audio tracks on DVDs that have this feature when the DVD is playing. The format and content of this function vary for each disc. { (Subtitles): Press to turn ON/OFF subti[...]

Problem Recommended Action No power. The ignition might not be turned ON/RUN or in ACC/ACCESSORY. The picture does not fill the screen. There are black borders on the top and bottom or on both sides or it looks stretched out. Check the display mode settings in the setup menu by pressing the display menu button on the remote control. In auxiliary mode, the picture moves or scrolls. Check the auxiliary input connections at both devices. The remote control does not work. Check to make sure there is no obstruction between the remote control and the transmitter window. Check the batteries to make sure they are not dead or installed incorrectly. After stopping the player, I push Play but sometime[...]

Problem Recommended Action Sometimes the wireless headphone audio cuts out or buzzes. Check for obstructions, low batteries, reception range, and interference from cellular telephone towers or by using a cellular telephone in the vehicle. Check that the headphones are on correctly using the L (left) and R (right) on the headphones. I lost the remote and/or the headphones. See your dealer/retailer for assistance. The DVD is playing, but there is no picture or sound. Check that the RSE video screen is sourced to the DVD player. DVD Display Error Messages The DVD display error message depends on which radio the vehicle has. The video screen might display one of the following: Disc Load/Eject Er[...]

Rear Seat Audio (RSA) For vehicles with Rear Seat Audio (RSA), rear seat passengers can listen to and control any of the music sources: radio, CDs, DVDs, or other auxiliary sources. The rear seat passengers can only control the music sources the front seat passengers are not listening to (except on some radios where dual control is allowed). For example, rear seat passengers can control a CD and listen to it through the headphones, while the driver listens to the radio through the front speakers. The rear seat passengers have control of the volume for each set of headphones. The RSA functions operate even when the main radio is off. The front audio system displays X when the RSA is on, and d[...]

P (Power): Press to turn the RSA on or off. Volume: Turn to increase or to decrease the volume of the wired headphones. The left knob controls the left headphones and the right knob controls the right headphones. SRCE (Source): Press to select between the radio (AM/FM/XM™), CD, and if the vehicle has these features, DVD, front auxiliary, and rear auxiliary. ©¨ (Seek): Press to go to the previous or to the next station and stay there. This function is inactive, with some radios, if the front seat passengers are listening to the radio. Press and hold © or ¨ until the display flashes to tune to an individual station. The display stops flashing after the buttons have not been pushed for [...]

When a disc is playing in the CD or DVD changer, press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a DVD video menu is being displayed, press PROG to perform the ENTER menu function. Theft-Deterrent Feature THEFTLOCK ® is designed to discourage theft of the vehicle’s radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle. Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjust[...]

SRCE (Source): Press to switch between the radio (AM, FM, XM), CD, and for vehicles with, DVD, front auxiliary, and rear auxiliary. For vehicles with the navigation system, press and hold this button for longer than one second to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information. + e − e (Volume): Press to increase or to decrease the radio volume. ¨ (Seek): Press to go to the next radio station while in AM, FM, or XM™. Press ¨ to go to the next track or chapter while sourced to the CD or DVD slot. Press the ¨ if multiple discs are loaded to go to the next disc while sourced to a CD player. Radio Reception Frequency interferenc[...]

Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off. Multi-Band Antenna The multi-band antenna is located on the roof of the vehicle. This type of antenna is used with the AM/FM radio, as well as OnStar ® and the XM™ Satellite Radio Service System, if the vehicle has these features. Keep this antenna clear of snow and ice build up for clear radio [...]

✍ NOTES 3-128 Instrument Panel[...]

Driving Your Vehicle Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy ........................... .4-1 Defensive Driving ................. .4-2 Drunk Driving ...................... .4-2 Control of a Vehicle .............. .4-3 Braking ............................... .4-3 Antilock Brake System (ABS) .................... .4-4 Braking in Emergencies ......... .4-5 StabiliTrak ® System .............. .4-5 All-Wheel Drive (AWD) System ............................. .4-7 Steering .............................. .4-8 Off-Road Recovery ............... .4-9 Passing .............................. .4-9 Loss of Control .................. .4-10 Driving at Night .................. .4[...]

• Keep vehicle tires properly inflated. • Combine several trips into a single trip. • Replace the vehicle’s tires with the same TPC Spec number molded into the tire’s sidewall near the size. • Follow recommended scheduled maintenance. Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-14 . { CAUTION Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: • Allow enough following distance between you and the driver [...]

Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person’s system can make crash injuries worse,[...]

And, of course, actual stopping distances vary greatly with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the vehicle; and the amount of brake force applied. Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traff ic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking. Keeping pace with the traff ic and allowing realistic following distances eliminates a lot of unnecessary braking. That [...]

As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let antilock work. The antilock pump or motor operating might be heard and the brake pedal might be felt to pulsate, but this is normal. Braking in Emergencies ABS allows the driv[...]

The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. The system should initialize before the vehicle reaches 20 mph (32 km/h). In some cases, it may take approximately two miles (3.2 km) of driving before the system initializes. If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, SERVICE STABILITRAK. If these conditions are observed, turn the vehicle off, wait 15 seconds, and then turn it back on again to reset the system. If any of these messages still appear on t[...]

It may also be necessary to turn off the system when driving in extreme off-road conditions where high wheel spin is required. See If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-16 . Traction Control Operation The traction control system is part of the StabiliTrak system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The traction control system is enabled automatically when the vehicle is started. It will activate and the StabiliTrak light will flash if it senses that any of the wheels are spinning or beginning to lose traction while dri[...]

When using a compact spare tire on the AWD equipped vehicle, the AWD system automatically detects the presence of the compact spare and the AWD is disabled. To restore the AWD operation and prevent excessive wear on the AWD system, replace the compact spare with a full-size tire as soon as possible. See Compact Spare Tire on page 5-77 for more information. Steering Power Steering If power steering assist is lost because the engine stops or the system is not functioning, the vehicle can be steered but it will take more effort. Variable Effort Steering If the vehicle has this steering system, the system continuously adjusts the effort felt when steering at all vehicle speeds. It provides ease [...]

An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object. The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly. Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly [...]

Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger. Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems. In the braking skid, the wheels are not ro[...]

• Watch for animals. • When tired, pull off the road. • Do not wear sunglasses. • Avoid staring directly into approaching headlamps. • Keep the windshield and all glass on your vehicle clean — inside and out. • Keep your eyes moving, especially during turns or curves. No one can see as well at night as in the daytime. But, as we get older, these differences increase. A 50-year-old driver might need at least twice as much light to see the same thing at night as a 20-year-old. Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving thr[...]

Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. There is no hard and fast rule about hydroplaning. The best advice is to slow down when the road is wet. Other Rainy Weather Tips Besides slowing down, other wet weather driving tips include: • Allow extra following distance. • Pass with caution. • Keep windshield wiping equipment in good shape. • Keep the windshield washer fluid reservoir filled. • Have good tires with proper tread depth. See Tires on page 5-[...]

Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Other driving tips include: • Keep the vehicle well ventilated. • Keep interior temperature cool. • Keep your eyes moving — scan the road ahead and to the sides. • Check the rearview mirror and vehicle instruments often. Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission. ?[...]

Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive with caution, whatever the condition. Accelerate gently so traction is not lost. Accelerating too quickly causes the wheels to spin and makes the surface under the tires slick, so there is even less traction. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more[...]

{ CAUTION Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: • Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. • Check again from time to time to be sure snow does not collect there. • Open a window about two inches (5 cm) on the side of the vehicle that is away from the wind to bring in fresh air. (Continued) CAUTION (Continued) • Fully open the air outlets on or under the instrument panel. • Adjust the Climate Control system to[...]

If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 4-16 . If the vehicle has a traction system, it can often help to free a stuck vehicle. Refer to the vehicle’s traction system in the Index. If stuck too severely for the traction system to free the vehicle, turn the traction system off and use the rocking method. { CAUTION If you let your vehicle’s tires spin at high speed, they can explode, and you or others could be injured. The vehicle can overheat, causing an engine compartment fire or other damage. Spin the wheels as little as possible an[...]

{ CAUTION Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle. Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will find the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), an[...]

Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs). 5. Determine the combined weigh[...]

A. Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 150 lbs (68 kg) × 5 = 750 lbs (340 kg). C. Available Cargo Weight = 250 lbs (113 kg). A. Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg). C. Available Cargo Weight = 0 lbs (0 kg). Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. Example 2 Example 3 Driving Your Vehicle 4-19[...]

Certification/Tire Label A vehicle specific Certification/ Tire label is attached to the rear edge of the driver’s door. The label shows the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer/retailer can help you with this. Be sure to spread out your load equally on both sides of the centerline. Never ex[...]

{ CAUTION Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in the cargo area of your vehicle. Try to spread the weight evenly. • Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. • Do not leave an unsecured child restraint in your vehicle. • When you carry something inside the vehicle, secure it whenever you can. • Do not leave a seat folded down unless you need to. Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if th[...]

Dinghy Towing If the vehicle is front-wheel-drive, it can be dinghy towed from the front. These vehicles may also be towed by putting the front wheels on a dolly. See “Dolly Towing” later in this section. If the vehicle is all-wheel-drive, it can be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. These vehicles cannot be towed using a dolly. For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Re-install the fuse to start the vehicle. To tow the vehic[...]

Notice: If the vehicle is towed without performing each of the steps listed under “Dinghy Towing,” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle. Notice: If 65 mph (105 km/h) is exceeded while towing the vehicle, it could be damaged. Never exceed 65 mph (105 km/h) while towing the vehicle. Once the destination is reached: 1. Set the parking brake. 2. Reinstall the 50 amp BATT1 fuse to the underhood fuse block. 3. Shift the transmission to P (Park), turn the ignition to LOCK/OFF and remove the key from the ignition. 4. Disconnect the vehicle from the towing vehicle. Notice: Do not tow a vehicle[...]

Dolly Towing (Front-Wheel-Drive Vehicles Only) To tow a front-wheel-drive vehicle from the front with two wheels on the ground: 1. Put the front wheels on a dolly. 2. Move the shift lever to P (Park). 3. Set the parking brake. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Remove the key from the ignition. 6. Secure the vehicle to the dolly. 7. Release the parking brake. Towing the Vehicle From the Rear Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear. Do not tow the vehicle from the rear. 4-24 Driving Your Vehicle[...]

Towing a Trailer { CAUTION The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the vehicle warranty. Pull a trailer only if all the steps in this section have been followed. Ask your dealer/ retailer for advice and information about towing a trailer with the vehicle. To identify the trailering capacity of the vehicle, read the information in “Weight of the Trailer” that appears later in this se[...]

Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police. • Consider using a sway control. See “Hitches” later in this section. • Do not tow a trailer at all during the first 500 miles (800 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (800 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the e[...]

Vehicle Maximum Trailer Weight *GCWR Front-Wheel Drive 2,000 lbs (907 kg) 7,500 lbs (3 402 kg) Front-Wheel Drive, V92 Trailer Towing Package 5,200 lbs (2 359 kg) 10,250 lbs (4 649 kg) All-Wheel Drive 2,000 lbs (907 kg) 7,700 lbs (3 493 kg) All-Wheel Drive, V92 Trailer Towing Package 5,200 lbs (2 359 kg) 10,450 lbs (4 740 kg) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for the vehicle should not be exceeded. Ask your dealer/retailer for our trailering information or advice, or write us at our Customer Assistance Off ices. See Customer Assistance Off i[...]

After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren’t, adjustments might be made by moving some items around in the trailer. Trailering may also be limited by the vehicle’s ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the total of the additional weight. Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It h[...]

You may go further and think the tongue weight should be limited to less than 1,000 lbs (454 kg) to avoid exceeding GVWR. But the effect on the rear axle must still be considered. Because the rear axle now weighs 3,100 lbs (1 406 kg), 900 lbs (408 kg) can be put on the rear axle without exceeding RGAWR. The effect of tongue weight is about 1.5 times the actual weight. Dividing the 900 lbs (408 kg) by 1.5 leaves only 600 lbs (272 kg) of tongue weight that can be handled. Since tongue weight is usually at least 10 percent of total loaded trailer weight, expect that the largest trailer the vehicle can properly handle is 6,000 lbs (2 721 kg). It is important that the vehicle does not exceed any [...]

Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. Follow the manufacturer’s recommendation for attaching safety chains and do not attach them to the bumper. Always leave just enough slack so the rig can turn. Never allow safety chains to drag on the ground. Trailer Brakes A loaded trailer that weighs more than 1,000 lbs (450 kg) needs to have its own brake system that is adequate for the weight of the trailer. Be sure[...]

Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go much farther beyond the passed vehicle before returning to the lane. Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making Turns Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. The vehicle could be damaged. Avoid making very sharp turns while trailering. When turning with a trailer, make wider turns than normal. D[...]

Tow/Haul Mode Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. The purpose of the Tow/Haul mode is to: • Reduce the frequency and improve the predictability of transmission shifts when pulling a heavy trailer or a large or heavy load. • Provide the same solid shift feel when pulling a heavy trailer or a large or heavy load as when the vehicle is unloaded. • Improve control of vehicle speed while requiring less throttle pedal activity when pulling a heavy trailer or a large or heavy load. • Increase the charging system voltage to assist in recharging a battery installed in a trailer. Press this button located on the console to turn on and turn [...]

Parking on Hills { CAUTION Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface. If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traff ic if facing uphill. 2. Have someone place chocks under the trailer wheels. 3. When the wheel chocks are in place, release the brake pedal until the chocks absorb the load. 4. Reapply the brake pedal. Then apply the parking brake and shift the transmission in[...]

Basic Trailer Wiring The trailer wiring harness, with a seven-pin connector, is located at the rear of the vehicle and is tied to the vehicle’s frame. The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer/retailer. The seven-wire harness contains the following trailer circuits: • Yellow: Left Stop/Turn Signal • Dark Green: Right Stop/Turn Signal • Brown: Taillamps • Black: Ground • Light Green: Back-up Lamps • Red/Black: Battery Feed • Dark Blue: Trailer Brake* *The fuse for this circuit is installed in the underhood electrical center, but the wires are not connected. They should be connected by your dealer/[...]

Service and Appearance Care Service Service ............................... .5-3 Accessories and Modifications ...................... .5-3 California Proposition 65 Warning ............................ .5-4 California Perchlorate Materials Requirements ....... .5-4 Doing Your Own Service Work ..................... .5-4 Adding Equipment to the Outside of the Vehicle .......... .5-4 Fuel Fuel ................................... .5-5 Gasoline Octane .................. .5-5 Gasoline Specifications ......... .5-5 California Fuel ..................... .5-5 Additives ............................. .5-5 Fuels in Foreign Countries ..... .5-6 Filling the Tank .................... .5-7 Filling a Porta[...]

Different Size Tires and Wheels ............................ .5-52 Uniform Tire Quality Grading ........................... .5-52 Wheel Alignment and Tire Balance ........................... .5-54 Wheel Replacement ............ .5-54 Tire Chains ........................ .5-55 If a Tire Goes Flat .............. .5-56 Tire Sealant and Compressor Kit ................. .5-57 Tire Sealant and Compressor Kit Storage ..... .5-64 Changing a Flat Tire ........... .5-65 Removing the Spare Tire and Tools ........................ .5-66 Removing the Flat Tire and Installing the Spare Tire ....................... .5-68 Secondary Latch System ..... .5-72 Storing a Flat or Spare Tire and Tools .............[...]

Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. Some of these accessories could even cause malfunction or damage not covered by the vehicle warranty. Damage to vehicle components resulting from the installation o[...]

California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many fluids, and some component wear by-products contain and/or emit these chemicals. California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/[...]

Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. If you are using gasoline rated at 87 octane or higher and you hear heavy knocking, the engine needs service. Gasoline Specifications At a minimum, [...]

For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors. Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containin[...]

Filling the Tank { CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel. The tethered fuel cap is located behind a hinged fuel door on the driver side of the vehicl[...]

The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-39 . If the vehicle has a Driver Information Center (DIC), the TIGHTEN GAS CAP message displays if the fuel cap is not properly installed. { CAUTION If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately. Notice: If you need a new fuel cap, be sure to get the right type. Your dealer/retailer can get one for you. If you get the wrong type, it might not fit properly. This ca[...]

Checking Things Under the Hood { CAUTION An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine. Hood Release To open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver’s side of the vehicle. 2. At the[...]

Engine Compartment Overview When you lift the hood, here is what you will see: 5-10 Service and Appearance Care[...]

A. Radiator Pressure Cap. See Cooling System on page 5-17 . B. Engine Coolant Recovery Cap. See Cooling System on page 5-17 . C. Remote Negative ( − ) Terminal. See Jump Starting on page 5-29 . D. Underhood Fuse Block on page 5-88 . E. Remote Positive (+) Terminal. See Jump Starting on page 5-29 . F. Power Steering Fluid on page 5-24 . G. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-11 . H. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 5-11 . I. Automatic Transmission Fluid Dipstick. See “Checking the Fluid Level” under Automatic Transmission Fluid on page 5-16 . J. Brake Master Cylinder Reservoir. See “Brake Fluid” [...]

When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-92 . Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. See Engine Compartment Overview on page 5-10 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range in the cross-hatched area. Push the dipstick all the way back in when thro[...]

• GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. • American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not c[...]

When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on. Change the oil as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the oil life system might not indicate that an oil change is necessary for over a year. However, the engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service people who will perform this work using genuine parts and reset the system. It is also important to check the oil regularly and keep it at the proper level. If the syst[...]

If the vehicle has Driver Information Center (DIC) buttons: 1. Turn the ignition to ON/RUN, with the engine off. 2. Press the vehicle information button until OIL LIFE REMAINING displays. 3. Press and hold the set/reset button until 100% is displayed. Three chimes sound and the CHANGE ENGINE OIL SOON message goes off. 4. Turn the key to LOCK/OFF. If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and n[...]

To inspect or replace the engine air cleaner/filter: 1. Loosen the screws that hold the cover on. 2. Disconnect the electrical connector. 3. Lift off the cover. 4. Remove the engine air cleaner/ filter element and any loose debris that may be found in the air cleaner base. 5. Inspect or replace the air filter element. 6. Reverse Steps 1 through 3 to reinstall the cover and reconnect the electrical connector. { CAUTION Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. If it is not there and the engine backfires, you could be burned. Do not drive with it off[...]

The transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature. If you need to check the transmission fluid level, please take the vehicle to your dealer/retailer. Cooling System The cooling system allows the engine to maintain the correct working temperature. A. Engine Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Cooling Fans { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, y[...]

What to Use { CAUTION Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant. Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: • Gives freezing protection down to − 34°F ( ?[...]

Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant recovery tank, but be sure the cooling system is cool before this is done. See Engine Coolant on page 5-17 for more information. The coolant recovery tank cap has this symbol on it. When the engine is cold, the coolant level should be at or above the FULL COLD line marked on [...]

How to Add Coolant to the Radiator { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. (Continued) CAUTION (Continued) Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap. If coolant is need[...]

6. Fill the coolant recovery tank to the FULL COLD mark. 7. Reinstall the cap on the coolant recovery tank but leave the radiator pressure cap off. 8. Start the engine and let it run until the upper radiator hose feels warm. Any time during this procedure, watch out for the engine cooling fan(s). 9. If the coolant level inside the radiator filler neck is low, add more of the proper DEX-COOL coolant mixture through the filler neck until the level is back up to the base of the filler neck. Replace the pressure cap. Be sure to secure it tightly. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly sec[...]

Engine Overheating The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperature gage on the instrument panel cluster. See Engine Coolant Temperature Gage on page 3-38 . The vehicle may also display an ENGINE OVERHEATED IDLE ENGINE and ENGINE OVERHEATED STOP ENGINE message in the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-56 . You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 7-6 . If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If [...]

If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • Climbs a long hill on a hot day. • Stops after high-speed driving. • Idles for long periods in traff ic. • Tows a trailer. If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary. 3. If in a traff ic jam, shift to N (Neutral), otherwise, shift to the highest gear while driving —D (Drive) or L (Low). If the tempe[...]

Power Steering Fluid The power steering fluid reservoir is located toward the front of the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 5-10 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering fluid: 1. Turn the key off and let the engine compartment cool down. 2. Remove engine oil fill cap. 3. Slide engine cover rearward and lift to remov[...]

Adding Washer Fluid When the windshield washer fluid reservoir is low, a WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-56 for more information. Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 5-10 for reservoir location. Notice: • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water does not clean as well as [...]

There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up. • A fluid leak in the brake hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system. {[...]

Notice: • Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. • If brake fluid is spilled on the vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately. See Washing Your Vehicle on page 5-81 . Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads ar[...]

Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts. If this is not done, the brakes might not work properly. For example, if someone puts in brake linings that are wrong for the vehicle, the balance between the f[...]

Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you. Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Ch[...]

Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio! 4. Open the hoods and locate the positive (+) and negative ( − ) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative ( − ) ju[...]

Do not connect positive (+) to negative ( − ) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative ( − ) cable to the negative ( − ) terminal on the dead battery because this can cause sparks. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery. Use a remote negative ( − ) t[...]

10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. A. Heavy, Unpainted Metal Engine Part or Remote Negative ( − ) Terminal B. Good Battery or Remote Positive (+) and Remote Negative ( − ) Terminals C. Dead Battery or Remote [...]

Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-aimed, it is recommended that you take the vehicle to your dealer/retailer for service. Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-34 . For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs { CAUTION Halogen bulbs have pressurized gas inside and can bu[...]

3. Remove the two taillamp nut covers. 4. Remove the two nuts holding the taillamp assembly in place. 5. Pull out the taillamp assembly. 6. Turn the bulb socket counterclockwise and pull it straight out to remove it from the taillamp assembly. 7. Pull the old bulb straight out of the bulb socket. 8. Push the new bulb straight into the bulb socket until it connects. 9. Push the taillamp assembly back into its original location. When reinstalling the taillamp assembly, make sure the pin on the taillamp assembly lines up and is inserted correctly into the opening of the vehicle. 10. Reinstall the two nuts that hold the taillamp assembly in place. 11. Reinstall the two taillamp nut covers. Repla[...]

Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-3 for more information. Replacement blades come in different types and are removed in different ways. To replace the wiper blade assembly: 1. Pull the windshield wiper arm away from the windshield. 2. Press the button in the middle of the wiper arm connector and pull the wiper blade away from the arm connector. 3. Install the new wiper blade and make sure the wiper blade locks into place. For the proper size and type see Maintenance Replacement Parts on page 6-14 . Backglass Wiper Blade To replace the backglass wiper blade: 1. Pull the wiper blade assembly [...]

Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. { CAUTION Poorly maintained and improperly used tires are dangerous. • Overloading your vehicle’s tires can cause overheating as a result of too much flexing. You could have an air-out and a serious accident. See Loading the Vehicle on page 4-16 . • Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. (Continued) CAUTION (Continued) Check all tires freq[...]

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM’s specific tire performance criteria have a TPC specification code molded onto the sidewall. GM’s TPC specifications meet or exceed all federal safety guidelines.[...]

(A) Temporary Use Only : The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If your vehicle has a compact spare tire, see Compact Spare Tire on page 5-77 and If a Tire Goes Flat on page 5-56 . (B) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant [...]

Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width : The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as [...]

Bead : The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire : A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure : The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 5-42 . Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire [...]

Maximum Loaded Vehicle Weight : The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight : The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-16 . Occupant Distribution : Designated seating positions. Outward Facing Sidewall : The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire[...]

Vehicle Capacity Weight : The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading the Vehicle on page 4-16 . Vehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard : A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Loading the Vehicle on page 4-16 . Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that und[...]

When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. It should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 5-77 . How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated. Check the tire’s inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve st[...]

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel eff iciency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is[...]

Vehicles with TPMS operate on a radio frequency and comply with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, ex[...]

A Tire and Loading Information label, attached to your vehicle, shows the size of your vehicle’s original equipment tires and the correct inflation pressure for your vehicle’s tires when they are cold. See Loading the Vehicle on page 4-16 , for an example of the Tire and Loading Information label and its location on your vehicle. Also see Inflation - Tire Pressure on page 5-42 . Your vehicle’s TPMS can warn you about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection and Rotation on page 5-48 and Tires on page 5-36 . Notice: Using non-approved tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors. TPMS sensor damage[...]

• One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/ retailer for service. • Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Buying New Tires on page 5-50 . • Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction. If the TPMS is not functioning it cannot detect or si[...]

The TPMS sensor matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Press the Remote Keyless Entry (RKE) transmitter’s LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen. 4. Start with the driver side front tire. 5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor ident[...]

Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-50 and Wheel Replacement on page 5-54 . When rotating the vehicle’s tires, always use the correct rotation pattern shown here. If the vehicle has a compact spare tire, do not include it in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Inflation - Tire Pressure on page 5-42 and Loading the Vehicle on page 4-16 . Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-45 . [...]

When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when the tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. • The tire has a bump, bulge, or split. • The tire has a [...]

GM’s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 5-37 for additional information. GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less t[...]

Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 5-43 . Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. See Loading the Vehicle on page 4-16 , for more information about the Tire and Loading Information Label and its location on your vehicle. Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance[...]

The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specifi[...]

Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment might need to be checked. If you notice your vehicle vibrating when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer/retailer for pr[...]

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 5-65 for more information. Used Replacement Wheels { CAUTION Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains { CAUTION Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearan[...]

If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain the tires properly. See Tires on page 5-36 . If air goes out of a tire, It is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traff ic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would us[...]

Tire Sealant and Compressor Kit { CAUTION Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 2-30 . { CAUTION Over-inflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure. { CAUTION Storing the ti[...]

This vehicle may have one of the following tire sealant and compressor kits. The kit includes: A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer. See “Removal and Installation of the Sealant Canister” following. There i[...]

Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster. Always do a safety check first. See If a Tire Goes Flat on page 5-56 .D o not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-64 . Service and Appearance Care 5-59[...]

2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the sealant/air hose (F) onto the tire valve stem. Turn it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-17 . If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch t[...]

Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 7-6 . 11. Press the on/off button (B) to turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire, therefore, Steps 12 through 18 must be done immediately after Step 11. Be careful while handling the tire sealant [...]

20. Wipe off any sealant from the wheel, tire, and vehicle. 21. Dispose of the used sealant canister (E) and sealant/air hose (F) assembly at a local dealer/retailer or in accordance with local state codes and practices. 22. Replace it with a new canister available from your dealer/retailer. 23. After temporarily sealing a tire using the tire sealant and compressor kit, take the vehicle to an authorized dealer/retailer within a 100 miles (161 km) of driving to have the tire repaired or replaced. Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant: Always do a safety check firs[...]

4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-17 . If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window. 7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Turn the selector switch (A) clockwise to the Ai[...]

14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. 15. Place the equipment in the original storage location in the vehicle. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release button. 3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer/retailer. 5. Push the new canister into place. Tire Sealant and Compressor Kit Storage The tire sealant and [...]

Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-5 . { CAUTION Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake firmly. 2. Put the shift lever in P (Park). (Continued) CAUTION (Continued) 3. Turn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. To be even more certai[...]

Removing the Spare Tire and Tools The tools needed to remove the spare tire are located in the storage compartment on the driver side, at the rear of the vehicle. 1. Open the jack storage compartment by pulling on the latch tab, located toward the rear of the vehicle, and pulling the cover off. A. Tool Bag B. Wing Bolt C. Jack 2. Remove the wing bolt (B) by turning it counterclockwise 3. Push the jack (C) up out of the holding bracket. 4. Turn the jack on its side, with the bottom facing toward you. 5. Pull the jack straight out, bottom first. The tools you will be using include the jack (A) and lug wrench (B). Removing the Spare Tire The compact spare tire is located under the vehicle, in [...]

1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 2. Open the carpet cutout that is located through the hole of the storage compartment. 3. Attach the lug wrench into the hoist shaft. 4. Turn the lug wrench counterclockwise to lower the spare tire to the ground. Continue turning the wrench until the spare tire can be pulled out from under the vehicle. 5. Tilt the retainer and slip it through the wheel opening to remove the spare tire from the cable. 6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a flat road tire under the [...]

Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it is not visible, see Secondary Latch System on page 5-72 . If it is visible, first try to tighten the cable by turning the lug wrench clockwise until you hear two clicks or feel it skip twice. You cannot over-tighten the cable. 3. Loosen the cable by turning the wrench counterclockwise three or four turns. 4. If the spare tire has not lowered, tighten the cable all the way and then loosen it at least two times. If the spare tire did lower to the ground, continue with Step 5 under “Removing the Spare Tire (Vehicles with the Rear Convenience Center)” listed previously. 5. If you still c[...]

4. To identify the appropriate jacking location, find the triangle (A) about 12 inches (30.5 cm) from the front tire or (B) about 10.5 inches (27 cm) from the rear tire. The triangle is located near each wheel on the vehicle’s exterior. Notice: If a jack is used to raise the vehicle without positioning it correctly, the vehicle could be damaged. When raising the vehicle on a jack, avoid contact with the rear axle control arms. 5. Do not raise the vehicle yet. Put the compact spare tire near you. { CAUTION Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by[...]

9. Remove the plastic spare tire heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See Storing a Flat or Spare Tire and Tools on page 5-74 for more information. { CAUTION Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 5-65 . { CAUTION Never use oil or grease on bolts or[...]

12. Put the nuts on by hand by turning the clockwise until the wheel is held against the mounting surface. Make sure the rounded end is toward the wheel. 13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. { CAUTION Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque (Continued) CAUTION (Continued) specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 5[...]

Secondary Latch System This vehicle has an underbody mounted tire hoist assembly that has a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down. See Storing a Flat or Spare Tire and Tools on page 5-74 for instructions on storing the spare tire correctly. { CAUTION Before beginning this procedure read all the instructions. Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt. Read and follow the instructions listed next. To release the spare tir[...]

5. Turn the lug wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released and the spare tire is balancing on the jack. 7. Lower the jack by turning the lug wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack. 8. Disconnect the lug wrench from the jack and carefully remove the jack. Use one hand to push against the spare tire while firmly pulling the jack out from under the spare tire with the other hand. 9. Tilt the retainer and slip it through the wheel opening when the spare tire ha[...]

Storing a Flat or Spare Tire and Tools Storing the Spare Tire { CAUTION The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle. If this happened when the vehicle was being driven, the tire might contact a person or another vehicle, causing injury and damage to itself. Be sure the underbody-mounted spare tire is stored with the valve stem pointing down. { CAUTION Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or [...]

6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the lug wrench to tighten the cable. Storing the Flat Tire 1. Remove the cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 3. Put the flat tire in the rear storage area with the valve stem pointing toward the rear of the vehicle. 4. Pull the cable (A) through the door striker (E), the center of the wheel (D), and the plastic spare tire heat shield (C), as shown. 5. Hook the cable onto the outside portion of the liftgate hinges (B). 6. Hook the other end of[...]

8. Make sure the metal tube is centered at the striker. Push the tube toward the front of the vehicle. 9. Close the liftgate and make sure it is latched properly. Storing the Tools A. Tool Bag B. Wing Bolt C. Jack Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. 1. Ensure that the bottom of the jack is facing toward you. 2. Turn the jack (C) on its side and place down on the holding bracket. 3. Reinstall the wing bolt (B) by turning clockwise. 4. To replace the cover, line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the[...]

Compact Spare Tire { CAUTION Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. The compact spare tire, if the vehicle has one, was fully inflated when the vehicle was new, however, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you ca[...]

Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery. It is important to keep the upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. The vehicle’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to home furnishings m[...]

Do not clean the vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. • A stiff brush. It can cause damage to the vehicle’s interior surfaces. • Heavy pressure or aggressive rubbing with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectiveness of soil removal. • Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps. • Too much cleaner that saturates the upholstery. • Organic solvents such as naptha, alcohol, etc. that can damage[...]

Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of the leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean the vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Ne[...]

Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-12 . Washing Your Vehicle The best way to preserve the vehicle’s finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty. Do not wash the vehicle i[...]

If the vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon[...]

Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the vehicle’s chrome with soap and water after exposure. Notice: Using strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that con[...]

Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty. Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer/retailer. Larger areas of finish damage can be corrected in your dealer’s/retailer’s [...]

Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in the VIN is the engine code. This code helps identify the vehicle’s engine, specifications, and replacement parts. See “Engine Specifications” under Capacities and Specifications on page 5-92 for the vehicle’s engine code. Service Parts Identification Label [...]

Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle’s battery, even if the vehicle is not operating. The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-57 . Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due[...]

Fuses Usage AIRBAG Airbag AMP Amplifier BCK/UP/ STOP Back-up Lamp/Stoplamp BCM Body Control Module CNSTR/ VENT Canister Vent CTSY Courtesy DR/LCK Door Locks DRL Daytime Running Lamps DRL 2 GMC HID Only/Rear Fog Lamps-China Only DSPLY Display FRT/WSW Front Windshield Washer HTD/COOL SEAT Heated/Cooling Seats HVAC Heating, Ventilation and Air Conditioning Fuses Usage IADV/ PWR/LED Inadvertent Power LED INFOTMNT Infotainment LT/TRN/SIG Driver Side Turn Signal MSM Memory Seat Module PDM Power Mirrors, Liftgate Release PWR MODE Power Mode PWR/MIR Power Mirrors RDO Radio REAR WPR Rear Wiper RT/TRN/SIG Passenger Side Turn Signal SPARE Spare SPARE Spare STR/WHL/ ILLUM Steering Wheel Illumination Fu[...]

Relays Usage LT/PWR/ SEAT Driver Side Power Seat Relay RT/PWR/ SEAT Passenger Side Power Seat Relay Relays Usage PWR/ WNDW Power Windows Relay PWR/ COLUMN Power Steering Column Relay L/GATE Liftgate Relay LCK Power Lock Relay REAR/WSW Rear Window Washer Relay UNLCK Power Unlock Relay DRL2 Daytime Running Lamps 2 Relay LT/UNLCK Driver Side Unlock Relay DRL Daytime Running Lamps Relay SPARE Spare FRT/WSW Front Windshield Washer Relay Underhood Fuse Block The underhood fuse block is located in the engine compartment, on the passenger side of the vehicle. Lift the cover for access to the fuse/relay block. Notice: Spilling liquid on any electrical components on the vehicle may damage it. Always k[...]

Fuses Usage A/C CLUTCH Air Conditioning Clutch ABS MTR Antilock Braking System (ABS) Motor AFS Adaptive Forward Lighting System Fuses Usage AIRBAG Airbag System AUX POWER Auxiliary Power AUX VAC PUMP Auxiliary Vacuum Pump Fuses Usage AWD All-Wheel-Drive System BATT 1 Battery 1 BATT 2 Battery 2 BATT 3 Battery 3 ECM Engine Control Module ECM 1 Engine Control Module 1 EMISSION 1 Emission 1 EMISSION 2 Emission 2 EVEN COILS Even Injector Coils FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FOG LAMP Fog Lamps Service and Appearance Care 5-89[...]

Fuses Usage FSCM Fuel System Control Module HORN Horn HTD WASH Heated Windshield Washer Fluid HTD MIR Heated Outside Rearview Mirror HVAC BLWR Heating, Ventilation and Air Conditioning Blower LT HI BEAM Left High-Beam Headlamp LT LO BEAM Left Low-Beam Headlamp LT PRK Left Parking Lamp LT TRLR STOP/TRN Trailer Left Stoplamp and Turn Signal Fuses Usage ODD COILS Odd Injector Coils PCM IGN Powertrain Control Module Ignition PWR L/GATE Power Liftgate PWR OUTLET Power Outlet REAR CAMERA Rear Camera RR APO Rear Accessory Power Outlet RR DEFOG Rear Defogger RR HVAC Rear Climate Control System RT HI BEAM Right High-Beam Headlamp RT LO BEAM Right Low-Beam Headlamp Fuses Usage RT PRK Right Parking Lam[...]

Fuses Usage TRLR BRK Trailer Brake TRLR PRK LAMP Trailer Parking Lamps TRLR PWR Trailer Power WPR/WSW Windshield Wiper/Washer Relays Usage A/C CMPRSR CLTCH Air Conditioning Compressor Clutch AUX VAC PUMP Auxiliary Vacuum Pump CRNK Switched Power FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FAN 3 Cooling Fan 3 FOG LAMP Fog Lamps HI BEAM High-Beam Headlamps Relays Usage HID/LO BEAM High Intensity Discharge (HID) Low-Beam Headlamps HORN Horn IGN Ignition Main LT TRLR STOP/TRN Trailer Left Stoplamp and Turn Signal Lamp PRK LAMP Park Lamp PWR/TRN Powertrain RR DEFOG Rear Window Defogger RT TRLR STOP/TRN Trailer Right Stoplamp and Turn Signal Lamp Stop Lamps (China Only) Stop Lamps (China Only) TRLR BC[...]

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information. Cooling System 11.4 qt 10.8 L Engine Oil with Filter 5.5 qt 5.2 L Fuel Tank 22.0 gal 83.3 L Transmission Fluid* 5.3 qt 5.0 L Wheel Nut Torque 140 lb ft 190 Y *See Automatic Transmission Fluid on page 5-16 for information on checking fluid level. All capacities are approximate[...]

Maintenance Schedule Maintenance Schedule Introduction ......................... .6-1 Maintenance Requirements .... .6-1 Your Vehicle and the Environment ....................... .6-1 Using the Maintenance Schedule ........................... .6-2 Scheduled Maintenance ........ .6-3 Additional Required Services . . .6-6 Maintenance Footnotes ......... .6-7 Owner Checks and Services . . .6-9 At Each Fuel Fill .................. .6-9 At Least Once a Month ......... .6-9 At Least Once a Year ......... .6-10 Recommended Fluids and Lubricants ........................ .6-12 Maintenance Replacement Parts ............................... .6-14 Engine Drive Belt Routing .... .6-15 Maintenance Record ..[...]

Improper fluid levels or the wrong tire inflation can increase the level of emissions from the vehicle. To help protect the environment, and to keep the vehicle in good condition, be sure to maintain the vehicle properly. Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather. You might use the vehicle in making deliveries. Or you might drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs v[...]

To purchase service information, see Service Publications Ordering Information on page 7-15 . Owner Checks and Services on page 6-9 tells what should be checked, when to check it, and what can easily be done to help keep the vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-14 . When the vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine parts from your dealer/retailer. Scheduled Maintenance When the CHANGE ENGINE OIL S[...]

Maintenance I —U s e Maintenance I if the CHANGE ENGINE OIL SOON message displays within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II —U s e Maintenance II if the previous service performed was Maintenance I . Always use Maintenance II whenever the message displays 10 months or more since the last service or if the message has not come on at all for one year. Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-11 . Reset oil life system. See Engine Oil Life System on page 5-13 . An Emission Control Service. •• Visually check for any leaks or damage. See footnote (g). •• Ins[...]

Scheduled Maintenance (cont’d) Service Maintenance I Maintenance II Inspect brake system. See footnote (a). •• Check engine coolant and windshield washer fluid levels and add fluid as needed. •• Perform any needed additional services. See “Additional Required Services” in this section. •• Inspect suspension and steering components. See footnote (b). • Inspect engine cooling system. See footnote (c). • Inspect wiper blades. See footnote (d). • Inspect restraint system components. See footnote (e). • Lubricate body components. See footnote (f). • Inspect throttle system. See footnote (j). • Maintenance Schedule 6-5[...]

Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect fuel system for damage or leaks. • • ••• • Inspect exhaust system for loose or damaged components. • • ••• • Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-15 . •• • Change automatic transmission fluid (severe service). See footnote (h). ••• Change automatic transmission fluid (norma[...]

Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). • Inspect engine accessory drive belt. An Emission Control Service. See footnote (k). • Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. Check parking brake adjustment. (b) Visually inspe[...]

(e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also see Checking the Restraint Systems on page 1-59 . (f) Lubricate all key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats, and liftgate hinges. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last [...]

Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety, dependability, and emission control performance. Your dealer/ retailer can assist with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to the vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12 . At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Notice: It is important to check the engine oil regularly and keep it at the proper level. Failure to keep the engine oil at th[...]

At Least Once a Year Starter Switch Check { CAUTION When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 2-27 . Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts. 3. Try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer/ retailer for service. Automatic Transmission Shift Lock Control System Check { CAUTION Wh[...]

Parking Brake and Automatic Transmission P (Park) Mechanism Check { CAUTION When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking[...]

Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-11 . Engine Coolant 50/50 mixture of clean, drinkable water and use only DEX-COOL ® Coolant. See Engine Coolant on page 5-17 . Hydraulic Brake System DOT 3 Hydraulic Brake Fluid (GM Part No. U.S. 88862806, in Canada 88862807). Windshield Washer Optikleen ® Washer Solvent. Power St[...]

Usage Fluid/Lubricant Automatic Transmission DEXRON ® -VI Automatic Transmission Fluid. Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Carrier Assembly — Differential (Rear Drive Module) and Transfer Case (Power Transfer Unit) SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677 in Canada 89021678) meeting GM Specification 9986115. Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and Release Pawl Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Hood and Door Hinges and Rear Folding Seat Multi-Purpose Lubricant, Superlu[...]

Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15278634 — Engine Oil Filter 89017524 PF48 Spark Plugs 12611882 41-107 Wiper Blades Front Driver – 24.6 in (62.5 cm) 15254805 — Front Passenger – 20.8 in (53.0 cm) 15254804 — Rear – 11.6 in (30.0 cm) 25920067 — 6-14 Maintenance Schedule[...]

Engine Drive Belt Routing 3.6L V6 Engine Maintenance Schedule 6-15[...]

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-1 . Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts. Maintenance Record Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-16 Maintenance Schedule[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed Maintenance Schedule 6-17[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18 Maintenance Schedule[...]

Customer Assistance Information Customer Assistance and Information Customer Satisfaction Procedure .......................... .7-1 Online Owner Center ............ .7-3 Customer Assistance for Text Telephone (TTY) Users ................................ .7-4 Customer Assistance Off ices . . .7-5 GM Mobility Reimbursement Program ............................ .7-6 Roadside Assistance Program ............................ .7-6 Scheduling Service Appointments ..................... .7-8 Courtesy Transportation ........ .7-9 Collision Damage Repair ..... .7-10 Reporting Safety Defects Reporting Safety Defects to the United States Government ..................... .7-14 Reporting Safety Defects to th[...]

STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call the Chevrolet Customer Assistance Center at 1-800-222-1020. In Canada, call General Motors of Canada Customer Communication Centre at 1-800-263-3777 (English), or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention. Have the following information available to give the Customer Assistance Representative: • Vehicle Identification Number (VIN). This is available from the vehicle registration or title, or the plate at the top left of the instrument panel and visibl[...]

STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims. The program provides for the review of the facts involved by an impartial third party arbiter, and may include an informal hearing before the arbiter. The program is designed so that the entire dispute settlement process, from the time you file your complaint to the final decision[...]

Other Helpful Links: Chevrolet — www.chevrolet.com Chevrolet Merchandise — www.chevymall.com Help Center — www.chevrolet.com/ helpcenter • FAQ • Contact Us My GM Canada (Canada) — www.gm.ca My GM Canada is a password-protected section of www.gm.ca where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. Here are a few of the valuable tools and services you will have access to: • My Showroom: Find and save information on vehicles and current offers in your area. • My Dealers/Retailers: Save details such as address and phone number for each of your preferred GM dealers/retailers. • My Driveway: Access quick links[...]

Customer Assistance Of fices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 Chevrolet.com 1-800-222-1020 1-800-833-2438 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-CHEV-USA (243-8872) From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) From U.S. Virgin Islands: 1-800-496-9994 Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Dr[...]

GM Mobility Reimbursement Program This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/ scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease. For more details, or to determine your vehicle’s eligibility, visit gmmobility.com or call the GM Mobility Assistance Center at 1-800-323-9935. Text telephone (TTY) users, call 1-800-833-9935. General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. Roadside Assistance Program [...]

Coverage Services are provided up to 5 years/ 100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification. Chevrolet and General Motors of Canada Limited reserve the right to limit services or payment to an owner or driver if they decide the claims are made too often, or the same type of claim is made many times. Services Provi[...]

Services Not Included in Roadside Assistance • Impound towing caused by violation of any laws. • Legal fines. • Mounting, dismounting or changing of snow tires, chains, or other traction devices. • Towing or services for vehicles driven on a non-public road or highway. Services Specific to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. • Lock-Out Service: Vehicle registration is required. • Trip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route. Ther[...]

If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership/retailer, let them know this, and ask for instructions. If the dealer/retailer requests you to bring the vehicle for service, you are urged to do so as early in the work day as possible to allow for the same day repair. Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended [...]

Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts. This requires that you sign and complete a rental agreement and meet state/provincial, local, and rental vehicle provider requirements. Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc. You are responsible for fuel usage charges and may also be responsible for taxes, levies, usage fees, excessive mileage, or rental usage beyond the completion of the repair. It ma[...]

Recycled original equipment parts may also be used for repair. These parts are typically removed from vehicles that were total losses in prior crashes. In most cases, the parts being recycled are from undamaged sections of the vehicle. A recycled original equipment GM part, may be an acceptable choice to maintain your vehicle’s originally designed appearance and safety performance, however, the history of these parts is not known. Such parts are not covered by your GM New Vehicle Limited Warranty, and any related failures are not covered by that warranty. Aftermarket collision parts are also available. These are made by companies other than GM and may not have been tested for your vehicle.[...]

If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help. Do not leave the scene of a crash until all matters have been taken care of. Move your vehicle only if its position puts you in danger or you are instructed to move it by a police off icer. • Give only the necessary and requested information to police and other parties involved in the crash. Do not discuss your personal condition, mental frame of mind, or anything unrelated to the crash. This will help guard aga[...]

• Choose a reputable collision repair facility for your vehicle. Whether you select a dealer/ retailer or a private collision repair facility to fix the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time. • Once you have an estimate, read it carefully and make sure you understand what work will be performed on your vehicle. If you have a question, ask for an explanation. Reputable shops welcome this opportunity. Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of [...]

Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA) in addition to notifying General Motors. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer/retailer, or General Motors. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (T[...]

Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual[...]

Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle. These modules may store data to help your dealer/retailer technician service your vehicle. Some modules may also store data about how you operate the vehicle, such as rate of fuel consumption or average speed. These modules may also retain the owner’s [...]

GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an off icial request of police or similar government off ice; as part of GM’s defense of litigation through the discovery process; or, as required by law. Data that GM collects or receives may also be used for GM research needs or may be made available to others for research purposes, where a need is shown and the data is not tied to a specific vehicle or vehicle owner. OnStar ® If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on da[...]

✍ NOTES 7-18 Customer Assistance Information[...]

A Accessories and Modifications ...................... 5 - 3 Accessory Power ................. 2-22 Accessory Power Outlets ...... 3-17 Adding Equipment to Y our Airbag-Equipped V ehicle .... 1-58 Additional Required Services, Scheduled Maintenance ....... 6 - 6 Additives, Fuel ...................... 5 - 5 Add-On Electrical Equipment ....................... 5-86 Air Cleaner/Filter , Engine ....... 5-15 Air Conditioning ................... 3-19 Airbag Readiness Light ................ 3-33 Airbag System ..................... 1-46 Adding Equipment to Y our Airbag-Equipped V ehicle ........................ 1-58 How Does an Airbag Restrain? ..................... 1-51 Passenger Sensing System ...[...]

B Battery ............................... 5-28 Electric Power Management ................. 3-15 Run-Down Protection ......... 3-16 Belt Routing, Engine ............. 6-15 Blind Spot Mirrors ................ 2-34 Bluetooth ® ......................... 3-103 Brake Emergencies ...................... 4 - 5 Brake Fluid ......................... 5-25 Brakes ............................... 5-25 Antilock ............................. 4 - 4 Parking ........................... 2-27 System W arning Light ....... 3-36 Braking ................................ 4 - 3 Braking in Emergencies .......... 4 - 5 Break-In, New V ehicle .......... 2-20 Bulb Replacement ................ 5-34 F o g L a m p .........[...]

Cleaning (cont.) Instrument Panel, Vinyl, and Other Plastic Surfaces ...................... 5-80 Interior ............................ 5-78 Leather ........................... 5-80 T ires ............................... 5-83 Underbody Maintenance .... 5-84 W ashing Y our Vehicle ........ 5-81 Weatherstrips ................... 5-81 Windshield, Backglass, and Wiper Blades .......... 5-82 Climate Control System ......... 3-19 Outlet Adjustment ............. 3-27 Rear Air Conditioning and Heating System ............. 3-28 Rear Air Conditioning and Heating System, Electronic ..................... 3-29 Climate Control Systems Dual Automatic ................. 3-22 Clock, Setting ...................[...]

Driver Seat Height Adjuster ........... 1 - 3 Driver Information Center (DIC) .................... 3-44 DIC Operation and Displays ............... 3-45, 3-51 DIC V ehicle Customization ............... 3-65 DIC W arnings and Messages .................... 3-56 Driving At Night .......................... 4-10 Before a Long T rip ............ 4-12 Defensive .......................... 4 - 2 Drunk ............................... 4 - 2 Highway Hypnosis ............ 4-13 Hill and Mountain Roads .... 4-13 In Rain and on Wet Roads ................... 4-11 Loss of Control ................ 4-10 Off-Road Recovery ............. 4 - 9 Rocking Y our V ehicle to G e t i t O u t .................... 4-16 Wint[...]

F Filter Engine Air Cleaner ............ 5-15 Finish Damage .................... 5-84 Flashers, Hazard W arning ....... 3 - 5 Flash-to-Pass ........................ 3 - 7 Flat Tire .............................. 5-56 Flat Tire, Changing ............... 5-65 Flat T ire, Storing .................. 5-74 Floor Mats .......................... 2-54 Fluid Automatic T ransmission ..... 5-16 Power Steering ................. 5-24 Windshield W asher ........... 5-24 Fog Lamp F o g ................................ 3-13 Fuel ..................................... 5 - 5 Additives ........................... 5 - 5 California Fuel ................... 5 - 5 Economy Driving ................ 4 - 1 Filling a Por[...]

Hood Checking Things Under ....... 5 - 9 Release ............................ 5 - 9 H o r n .................................... 3 - 5 How to Wear Safety Belts Properly .......................... 1-17 I Ignition Positions .................. 2-21 Infants and Y oung Children, Restraints ........................ 1-29 Inflation - T ire Pressure ......... 5-42 Instrument Panel Brightness ....................... 3-13 Cluster ............................ 3-31 Overview ........................... 3 - 4 Storage Area .................... 2-52 Introduction ........................... 6 - 1 J Jump Starting ...................... 5-29 K Keyless Entry , Remote Operation .......................... 2 - 4 K[...]

Locks (cont.) P o w e r D o o r ....................... 2 - 8 Programmable Automatic Door Locks .................... 2 - 9 Rear Door Security Locks .... 2 - 9 Loss of Control .................... 4-10 Lower Anchors and T ethers for Children ...................... 1-35 Luggage Carrier ................... 2-54 Lumbar Manual Controls ................. 1 - 4 Power Controls .................. 1 - 5 M Maintenance Footnotes .......................... 6 - 7 Maintenance Schedule Additional Required Services ........................ 6 - 6 At Each Fuel Fill ................ 6 - 9 At Least Once a Month ....... 6 - 9 At Least Once a Y ear ....... 6-10 Maintenance Record ......... 6-16 Maintenance Replace[...]

Outside Convex Mirror .................. 2-35 Heated Mirrors ................. 2-35 Power Foldaway Mirrors .... 2-33 Power Mirrors .................. 2-32 Overheated Engine Protection Operating Mode ................ 5-23 Owner Checks and Services .... 6 - 9 Owners, Canadian .................... i i P Paint, Damage ..................... 5-84 Parade Dimming .................. 3-15 Park Shifting Into ..................... 2-28 Shifting Out of .................. 2-29 Park Aid ............................. 2-36 Park T ilt Mirrors ................... 2-35 Parking Assist ............................. 2-36 Over Things That Burn ...... 2-29 Parking Brake ...................... 2-27 Passenger Airbag S[...]

Rearview Mirror , Automatic D i m m i n g .......................... 2-31 Rearview Mirrors .................. 2-31 Reclining Seatbacks ............... 1 - 8 Recommended Fluids and Lubricants ........................ 6-12 Recreational V ehicle T owing . . . 4-21 Reimbursement Program, GM Mobility ....................... 7 - 6 Remote Keyless Entry (RKE) System ............................. 2 - 3 Remote Keyless Entry (RKE) System, Operation .............. 2 - 4 Remote V ehicle Start ............. 2 - 6 Removing the Flat T ire and Installing the Spare T ire ..... 5-68 Removing the Spare T ire and T ools ........................ 5-66 Replacement Bulbs .............. 5-34 Replacement Parts, Mainte[...]

Secondary Latch System ....... 5-72 Securing a Child Restraint Rear Seat Position ............ 1-41 Right Front Seat Position . . . 1-43 Security Light ...................... 3-43 Service ................................ 5 - 3 Accessories and Modifications .................. 5 - 3 Adding Equipment to the Outside of the V ehicle ..... 5 - 4 Doing Y our Own Work ........ 5 - 4 Engine Soon Lamp ........... 3-39 Publications Ordering Information ................... 7-15 Scheduling Appointments ..... 7 - 8 Service Parts Identification Label .............................. 5-85 Servicing Y our Airbag-Equipped V ehicle .... 1-57 Setting the Clock ................. 3-74 Sheet Metal Damage .........[...]

T ire Sealant and Compressor Kit ................ 5-64 T ires .................................. 5-36 Aluminum or Chrome-Plated Wheels, Cleaning ...................... 5-83 Buying New Tires ............. 5-50 Chains ............................ 5-55 Changing a Flat T ire ......... 5-65 Cleaning .......................... 5-83 Compact Spare ................ 5-77 Different Size ................... 5-52 If a T ire Goes Flat ............ 5-56 Inflation - T ire Pressure ..... 5-42 Inspection and Rotation ..... 5-48 Installing the Spare T ire ..... 5-68 Pressure Monitor Operation ..................... 5-45 Pressure Monitor System . . . 5-43 Removing the Flat T ire ...... 5-68 Removing the Spare T[...]

V entilation Adjustment ........... 3-27 Visors ................................. 2-16 V oltage Devices, and Wiring . . . 5-85 V oltmeter Gage .................... 3-35 W W arning Lights, Gages, and Indicators ........................ 3-30 W arnings DIC W arnings and Messages .................... 3-56 Hazard W arning Flashers .... 3 - 5 Safety and Symbols .............. i i i Wheels Alignment and T ire Balance ................. 5-54 Different Size ................... 5-52 Replacement .................... 5-54 When It Is T ime for New Tires ........................ 5-50 Where to Put the Child Restraint ................. 1-33 Windows ............................. 2-14 P o w e r ...............[...]