Chrysler 2005 Pacifica Touring manuel d'utilisation

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 6 3 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ...................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations ........... 7 1[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

INTRODUCTION 5 1[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. VEHICLE IDE[...]

VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 7 1[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 1 ▫ Ignition Key Removal ................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 2 䡵 Sentry Key ............................ 1 2 ▫ Replacement Keys ...................... 1 4 ▫ Customer Key Programming .............. 1 4 [...]

▫ T o T urn Off “Flash Lights On Lock/Unlock” . . .22 ▫ General Information .................... 2 3 ▫ T ransmitter Battery Service ............... 2 3 䡵 V ehicle Theft Alarm ...................... 2 4 䡵 Liftgate ............................... 2 6 ▫ Power Liftgate — If Equipped ............. 2 7 䡵 W indows .....................[...]

A WORD ABOUT YOUR KEYS Y ou can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer . Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The sh[...]

NOTE: The power window switches, radio, power sunroof, and power outlets will r emain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this featur e. W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children [...]

chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regar dless of whether or not the vehicle is locked or unlocked. During normal operation, the Theft Ala[...]

All of the keys provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the origi[...]

4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. The Keyless Entry T ransmitter will also be programmed during this procedure. Rep[...]

DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door , the door will lock. Therefor e, make sure the keys ar e not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle door[...]

If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you fr om acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as[...]

Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled, 2. the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h), 3. the transmission is in NEUTRAL or P ARK, 4. the driver door is opened (excluding liftgate), 5. the doors wer e not previously unlocked and 6[...]

T o activate the system, open the rear door and move the child lock control, located near the door’s r ear latch, to the ON position. When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. REMOTE KEYLESS ENTR Y This system allows you to lock [...]

NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of P ARK, all the transmitter buttons are disabled for all keys. T o unlock the doors and liftgate: Press and r elease the UNLOCK button on the transmitter once to unlo[...]

T o lock the doors and liftgate: Press and r elease the LOCK button on the transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal. If desired, the “Sound Horn On Lock” feature can be turned on and of f by referring to the Customer Programmable Featur es of the “Electronic V e- hicle Information Center ([...]

T o Open/Close Power Liftgate — If Equipped Press the LIFTGA TE button twice within five seconds to open/close the power liftgate. The liftgate will beep for 2 seconds and then open/close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position. If the liftgate is locked and is not equ[...]

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration. If your Remote Keyless Entr[...]

2. Remove and r eplace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3. T o reassemble the transmitter case, snap the two halves together . Make sure ther e is an even “gap” be- tween the two halves. T est transmitter operation.[...]

T o disarm the system: Press the UNLOCK button on the keyless entry transmitter . Also, using a valid sentry key and moving the ignition switch to the ON/ST AR T posi- tion will disarm the system. If you disarm the system and access the liftgate area, the system must be r earmed, as described previously , when closing the liftgate. If some- thing h[...]

The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system. LIFTGA TE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches [...]

be used to open the liftgate. The emergency liftgate latch release can be accessed thr ough a snap-in cover located on the liftgate trim panel. • If the liftgate is locked and is not equipped with a powered liftgate, pr essing the button on the remote keyless entry transmitter will result in the liftgate becoming unlocked for 30 seconds allowing [...]

W ARNING! During power operation, personal injury or cargo damage may occur . Ensure the liftgate travel path is clear . Make sure the liftgate is closed and latched before driving away . NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, pr ovid[...]

• If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually . W ARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. Y ou and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you a[...]

The window controls will operate only when the ignition switch is in the ON or ACCESSOR Y position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed the window contr ols on the passenger doors will not illuminate and the passen- ger windows will be disabl[...]

belts, your seat belts or the LA TCH feature (r efer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have differ ent rates of inflation that are based on collision severity . Please pay close attention to the[...]

The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. W ARNING! • It is extremely dangerous t[...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the r ear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go a[...]

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt[...]

4. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! • A lap belt worn too high can increas[...]

6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , ch[...]

As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position. Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ sh[...]

2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upwar d over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears[...]

Seat Belt Pretensioners The seat belts for both front seating positions ar e equipped with pretensioning devices that ar e designed to remove slack fr om the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners ar e des[...]

The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or RUN position. DaimlerChrysler does not recommend deactivating the Enhanced W arning System (BeltAlert). 1. T ur[...]

Seat Belts and Pregnant Women W e recommend that pr egnant women use the seat belts throughout their pr egnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug acr oss the hips as possible. Keep the belt low so that it does not come across the abdome[...]

Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartm[...]

NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag[...]

Airbags inflate in moderate to high speed impacts. Along with seat belts, and pretensioners, fr ont airbags work with the instrument panel knee blockers to pr ovide improved pr otection for the driver and front passenger . Left and right side curtain airbags also work with seat belts to improve occupant pr otection. The seat belts are designed to p[...]

If a child from 1 to 12 years old must ride in the fr ont passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. Y ou should read the instructions pr ovided with your child restraint to make sur e that you are using it pr operly . 2. All occu[...]

“The Front Airbag System” consists of the following: • Airbag Control Module (with integrated impact sen- sor) • AIRBAG Readiness Light • Driver Airbag • Front Passenger Airbag • Seat Belt Pretensioners • Steering Wheel and Column • Instrument Panel • Seat Belt Readiness Light • Interconnecting W iring • Passenger Knee Impac[...]

The airbag control module sends a message to the instrument cluster to turn on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned ON, then turns the light off. If the airbag control module detects a malfunction in any part of the system, the airbag light will turn on either momen- tarily or continuo[...]

the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and inflates (in about the same time it takes to blink your eyes). A properly belted and seated occupant is less likely to be injured by the force of the[...]

• Airbag Control Module • Interconnecting W iring If An Airbag Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-sever e col- lision, to help restrain the driver and fr ont passenger , and then immediately deflate. NOTE: A collision that is not sever e enough to need airbag protecti[...]

W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an autho- rized dealer as soon as possible. Enhanced Accident Response If the airbags and seat belt pertensioners deploy after an impact and the electrical system remains functional, vehicles equip[...]

Airbag Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately . • The AIRBAG light does not come on or flickers during the 6 to 8 seconds when the ignition swit[...]

W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper [...]

The tether anchors are located on the r ear surface of the seat. Child restraint systems designed to be compatible with the vehicles LA TCH System are now available. LA TCH child restraints make installation into the vehicle simple and convenient. When using the LA TCH System, always follow the child restraint manufactur es installation instruction[...]

T ether Anchors There ar e tether strap anchorages behind all second row seating positions and the driver’s side third r ow seating position. The tether anchors are located in the r ear surface of the seat. When using the tether anchorages in the second row seating position, ensur e that the strap is routed over the top of the seatback and under [...]

Infants and Children There ar e differ ent sizes and types of restraints for children fr om newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is corr ect for your child: • Safety experts recommend that childr[...]

• The belt-positioning booster seat is for children weigh- ing more than 18 kg (40 lbs), but who ar e still too small to fit the vehicle’s seat belts properly . If the child can not sit with knees bent over the vehicles seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and[...]

that you can install the child restraint in the vehicle where you will use it, befor e you buy it. • The restraint must be appr opriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instr uctions that come with the restraint. If you install the r estraint improperly ,[...]

In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint r earward and downwar d into the seat. Child restraint systems having attachments designed to conn[...]

Children T oo Large For Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be lo[...]

The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur . The recommended viscosity and quality grades ar e shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NE[...]

W ARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. D[...]

Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tr ead wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tr ead and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for pr oper pressure. Lights Have som[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 6 7 ▫ Inside Day/Night Mirror ................. 6 7 ▫ Automatic Dimming Mirror — If Equipped .... 6 7 ▫ Driver’s Side Outside Mirror Auto Dimmer — If Equipped ............................ 6 8 ▫ Exterior Mirrors Folding Featur e ..........[...]

䡵 Seats ................................. 9 3 ▫ 10–W ay Driver’s Power Seat — If Equipped . . . 93 ▫ 8–W ay Driver’s Power Seat — If Equipped .... 9 3 ▫ 4–W ay Passenger’s Power Seat ............. 9 3 ▫ Adjustable Head Restraints ............... 9 4 ▫ Heated Seats — If Equipped .............. 9 4 ▫ Second Row Manual [...]

▫ T urn Signals ......................... 1 1 2 ▫ Highbeam/Lowbeam Select Switch ......... 1 1 3 ▫ Passing Light ........................ 1 1 3 䡵 W indshield W ipers And W ashers ........... 1 1 3 ▫ W indshield W ashers ................... 1 1 3 ▫ Mist Feature ......................... 1 1 4 ▫ W indshield W iper Operation ............[...]

▫ Erasing Homelink Buttons ............... 1 2 7 ▫ Reprogramming a Single Homelink Button . . . 128 ▫ Security ............................ 1 2 8 䡵 Power Sunroof — If Equipped ............. 1 2 9 ▫ Express Open Featur e .................. 1 2 9 ▫ W ind Buffeting ....................... 1 3 1 ▫ Sunroof Maintenance ...................[...]

MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be adjuste[...]

CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn this[...]

W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror . Power Remot[...]

Power mirror pr eselected positions can be controlled by the optional Memory Seat Feature. Refer to “Memory Seat” in section 3 of this manual. Heated Remote Control Mirrors These mirrors ar e heated to melt frost or ice. This featur e is activated whenever you turn on the Rear W indow Defrost. Illuminated V anity Mirrors An illuminated vanity m[...]

HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., ⬙ Call ѧ Mike ѧ W ork ⬙ or ⬙ Dial ѧ 248-555-1212 ⬙ ). Y our cellular phone’s audio is transm[...]

The rearview mirr or contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙ Operation ⬙ section. The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth[...]

UConnect™ system prompts. Y ou will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙ Ready ⬙ prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying ⬙ Setu[...]

Pair (Link) UConnect™ System to a Cellular Phone T o begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone (re- fer to ⬙ Introduction ⬙ section to learn about the phone type). T o complete the pairing process, you will need to refer ence your cellular phone owner’s manual. One of the followin[...]

only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority 3 and priority 5 phones are pr esent in the vehicle, the UConnect™ system will use the priority 3 cell[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a pr evi- ously stored name entry in the UConnect™ phone- book. Refer to section ⬙ Add Names to Y our UCon- nect™ Phonebook, ⬙ to learn how to store a name in the phonebook. •[...]

Edit Entries in the UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Edit. ⬙ • Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, cho[...]

• After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager . Say the designation you wish to delete. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Erase Al[...]

accessed through the UConnect™ system. Check with your cellular service provider for the featur es that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call[...]

T oggling Between Calls If two calls are in pr ogress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in pr ogress (one active and one on hold), press [...]

Call Continuation Call continuation is progr ession of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality can be of three types: • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condit[...]

Emergency Assistance If you are in an emer gency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emer gency number as follows: • Press the ’Phone’ button to begin. • After the ⬙ Ready ?[...]

V oice Mail Calling T o learn how to access your voice mail, refer to section ⬙ W orking with Automated Systems. ⬙ W orking with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated tele- phony system. Y ou can use your UConn[...]

• Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The UConnect™ system will play the current confirmation pr ompt status and you will be given the choice to change it. Phone and Network Status Indicators The UConnect™ system will provide notification to inform [...]

In order to un-mute the UConnect™ system: • Press the ’V oice Recognition’ button. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Mute-off. ⬙ Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stock[...]

• The UConnect™ system will play the phone names of all paired cellular phones in or der from the highest to the lowest priority . Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously pair ed to the UConnect™ system that you want to use i[...]

Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking. • Speak normally , without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Perform[...]

• Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero). ⬙ 800 ⬙ must be spoken ⬙ eight-zero-zer o. ⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far End Audio Performance: • Audio quality is maximized under: • low-to-medium [...]

Reset In rare instances, it may be necessary to r eset the UCon- nect™ system. The reset featur e is exercised by pr essing and holding the ’UConnect™ ’ and ’V oice Recognition’ buttons simultaneously for 15 seconds. Normally , you do not need to exercise this featur e. Power-Up After switching ignition key from of f to either On or ACC[...]

90 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 91 3[...]

92 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

SEA TS 10–W ay Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch con- trols up/down, forwar d/rearwar d, and tilt adjustment. The top switch controls the seatback r ecline adjustment and the middle switch controls the lumbar adjustment. W ARNING! Adjust [...]

CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjustable Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Pull [...]

Press the switch once to select a heat setting (high or low) and press the switch a second time in the same dir ection to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON. The controls for the second r ow heated seats are located on the center console between the seats. Press the switch once to select a heat setti[...]

heated seat is not functioning properly and that ser - vice is requir ed. See your authorized dealer for service. • Once a heat setting is selected, heat will be felt within 2 to 3 minutes. • The heated seats will turn off when the ignition switch is turned to the OFF position. Second Row Manual Seat Recliner The recliner mechanism contr ol is [...]

W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Second Row Manual Seat Adjuster The adjusting bar is located under the front of the seat. Pull t[...]

W ARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Fold & T umble Seats The second row seats can be folded and tumbled forwar d for easy access to the third seat or r ear cargo area. T o fold and [...]

5. Pull up on the r elease handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the fr ont seat, move the front seat forward. T o relatch the seat, tilt the seat r earward and push down firmly to engage the rear attachments. Then lift the seatback release lever labeled “1” and pull the seatba[...]

1. Pull up on the seatback r elease handle “1” located on the back of the seat to fold the seatback down. 2. Pull the r elease strap “2” located at the bottom of the seat to lift and tumble the seat forward. T o relatch the seat, tilt the seat r earward and push down firmly to engage the rear attachments. Then lift the seatback release leve[...]

Third Row Seating Flexibility The third r ow seats may be used with either or both seatbacks folded forward for additional storage space. T o fold the seat, remove any objects fr om in front of or on the seat. Then pull handle located on the seatback and push it forward. W ARNING! Do not sit in the 3rd row seat with the second row seatbacks folded [...]

W ARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat. • The cargo area in the rear of the vehicle should not be us[...]

NOTE: Be sure to r eattach the strap to secure the load floor panel when not in use. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all fr ont seats. The floor supports the partial weight of the bagged goods. UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 103 3[...]

DRIVER MEMOR Y SYSTEM — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions. The memory seat buttons located on [...]

Y our vehicle has been delivered with two r emote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any com[...]

Repeat the above steps for the second position using the other driver’s door numbered button and Remote Key- less Entry T ransmitter . Each time the SET (S) button and a numbered button ar e pressed, you erase the old memory and stor e a new one. T o Disable A T ransmitter Link, Follow These Steps: 1. Select “Remote Linked T o Memory” from th[...]

TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Next, push to the left the safety catch located under the front edge of the hood, near the center . Use the hood prop r od to secure the hood in the open position. T o prevent possible da[...]

W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by p[...]

Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. T urn the ignition switch ON to restor e the interior light operation. Multi-Function Lever The Multi-Function Lever controls the oper[...]

Headlights, Parking Lights, Instrument Panel Lights T urn the end of the Multi-Function Lever to the first detent for parking light and instrument panel light operation. T urn to the second detent for headlight, park light and instrument panel light operation. T o change the brightness of the instrument panel lights, rotate the center portion of th[...]

Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upwar d to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels. T o turn the syst[...]

T o activate the delay feature, turn of f the ignition switch while the headlights are still on. Then turn of f the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. If the head[...]

Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light Y ou can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you. This will cause the headlights to turn on at hig[...]

If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF . Mist Feature Push down on the wiper lever to activate a single wipe to clear off r oad mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Windshield Wiper Operation Rotate the end [...]

Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper . Push the lever forward to initiate the r ear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed. Upon release, the r ear wiper will cycle two times before r eturn- ing [...]

TIL T STEERING COLUMN T o tilt the column, pull the lever , located behind the turn signal control, towar d you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you co[...]

T o turn the system back ON, press the switch a second time until the traction control Indicator turns OFF . NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF . • The T raction Control system will make buzzing or clicking sounds when in [...]

ADJUST ABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away fr om the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the driver[...]

CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater[...]

W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidently set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you aren’t using it. T o Set At A Desired Speed: When the vehicle has reached the desir ed speed, press a[...]

is tapped, speed increases so that tapping the button three times will incr ease speed by 6 mph (10 km/h), etc. T o decrease speed while speed contr ol is set, press and hold the “COAST” button. Release the button when the desired speed is r eached, and the new speed will be set. T apping the “COAST” button once will result i na1m p h (2 km[...]

OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/r eading lights, an optional universal garage door opener (HomeLink 威 ), storage for sunglasses, optional power sunroof switches and an optional power liftgate switch. Courtesy/Reading Lights At the forward end of the console ar e two courtesy/ reading lights. Press the le[...]

GARAGE DOOR OPENER — IF EQUIPPED The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal T ransceiver operates off your vehicle’s battery and char[...]

Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. Some vehicles may requir e the ignition switch to be turned to the second (or ⬙ accessories ⬙ ) position for programming and/or opera- tion of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of [...]

W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inch[...]

If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with ⴖ Program- ming ⴖ steps 6-8 to complete the programming of a r olling code equipped device (most commonly a garage door opener). 6. At the garage door opener r eceiver (motor-head unit) in the garage, locate the ⬙ learn ⬙ or ⬙ smart ⬙ [...]

If you live in Canada or you are having dif ficulties programming a gate operator by using the ⬙ Pr ogram- ming ⬙ procedur es (regardless of wher e you live), replace ⴖ Programming HomeLink ⴖ step 3 with the following: NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the ⬙ cycling ⬙ [...]

Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Pr ess and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink button, proceed with ⬙ Programming ⬙ step [...]

POWER SUNROOF — IF EQUIPPED The power sunroof switches ar e located between the sun visors on the overhead console. Press and hold the switch r earward to fully open the sunroof. The sunr oof can be stopped at any position between closed and full open. Momentarily pressing the switch rearwar d will activate the Express Open Featur e, causing the [...]

and the glass will automatically stop at the comfort stop position. Pressing the switch r earward again will fully open the sunroof. During the Express Open operation, any movement of the switch will stop the sunroof and it will r emain in a partial open position. Again, momentarily pressing the switch rearwar d will activate the Express Open Featu[...]

Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with[...]

A thir d outlet is located on the back of the front center console near the floor , and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo ar ea and is also controlled by the ignition switch. The outlets include tethered caps labeled with a key or battery symbol indicating the power sourc[...]

CUPHOLDERS Front Seat Cupholders The cupholders are located in the forwar d edge of the center console. Push down on the forward edge of the console to release the cupholders. Pr ess the cover up when the cupholders are no longer needed. Second Row Seat Cupholders The second row seat cupholders ar e located in the forward edge of the center console[...]

Rear Cargo Storage Bin The storage bin is located in the floor of the rear car go area. T o open lift up on the handle. Retractable Cargo Area Cover — If Equipped T o cover the cargo ar ea: 1. Fold down the thir d row seatbacks. 2. Unfold the car go cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots l[...]

W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. Stowed Position 1. Fold[...]

W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center[...]

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails ar e designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the r oof rack crossbars. The roof rack does not incr ease the tota[...]

CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appro- priately . • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be sec[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Contr ols ................. 1 4 2 䡵 Instrument Cluster ...................... 1 4 3 䡵 Instrument Cluster Descriptions ............ 1 4 4 䡵 Electronic V ehicle Information Center (EVIC) . . . 151 ▫ Customer Programmable Featur es — If Equipped ......................... 1 5 [...]

▫ Radio Operation ...................... 1 6 6 ▫ T ape Player Operation .................. 1 7 0 ▫ CD Player Operation ................... 1 7 2 ▫ CD/DVD Changer Operation — If Equipped . 173 䡵 6 Disc CD/DVD Changer (Rdv) — If Equipped . 175 ▫ Operating Instructions — CD/DVD Changer . . 175 ▫ Eject (EJT) Button .................[...]

▫ Satellite Antenna ...................... 1 8 9 ▫ Reception Quality ..................... 1 8 9 䡵 Remote Sound System Controls ............. 1 9 0 ▫ Radio Operation ...................... 1 9 0 ▫ T ape Player ......................... 1 9 0 ▫ CD Player .......................... 1 9 1 䡵 Radio General Information ................ 1 9 [...]

INSTRUMENTS AND CONTROLS 142 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 143 4[...]

INSTRUMENT CLUSTER DESCRIPTIONS 1. V oltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the char ging system. Immediate service should be obtained. 2. T emperature Gauge The temperature gauge shows[...]

W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 3. Fuel Gauge The po[...]

is not functioning and that service is requir ed. However , the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restor e the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is [...]

V ehicles equipped with Anti-Lock brakes (ABS), ar e also equipped with Electronic Brake For ce Distribution (EBD). In the event of an EBD failure, the Brake W arning Light will turn on along with the ABS Light. Immediate repair to the ABS system is requir ed. The operation of the Brake W arning Light can be checked by turning the ignition switch f[...]

disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the T raction Contr ol Light. 9. T achometer The red segments indicate the maximum permissible engine revolutions-per -minute (r .p.m. x 1000) for each gear range. Before r eaching the red ar ea, ease up on the accelerator . 10. T rip Od[...]

release the T rip Odometer button. T o reset a trip odom- eter , display the desired trip odometer to be r eset then push and hold the button until the display resets (ap- proximately 2 seconds). 14. Cruise Indicator This display indicator shows that the Speed Control System is ON. 15. Malfunction Indicator Light This light is part of an onboard di[...]

18. Fr ont Fog Light Indicator — If Equipped This light shows the front fog lights ar e ON. 19. Oil Pr essure W arning Light This light shows low engine oil pressur e. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A continuous chi[...]

Driving on a significantly underinflated tire causes the tire to over heat and can lead to tire failur e. Underinfla- tion also reduces fuel ef ficiency and tire tr ead life, and may affect the vehicle’s handling and stopping ability . Each tire, including the spar e, should be checked monthly when cold and set to the recommended inflation pressu[...]

• Compass display — If Equipped • Mini-T rip functions — If Equipped Pressing the MENU button will change the displayed programming featur es. Pressing the STEP button will display the available choices. Pressing the MENU button a second time accepts a selected choice. When the appropriate conditions exist, the Electr onic V ehicle Informat[...]

• UNLOCK TO OPEN LIFTGA TE (with a single chime) • PUT IN P ARK FOR LIFTGA TE (with a single chime) • TOO COLD FOR PWR LIFTGA TE (with a single chime) • TOO HOT FOR PWR LIFTGA TE (with a single chime) • PERFORM SER VICE (with a single chime) • LEFT/RIGHT FRONT DOOR AJAR (one or mor e, with a single chime if speed is above 1 mph) • LEF[...]

• 1,2,3 OR 4 TIRE(S) HIGH PRESSURE (Refer to “Start- ing And Operating, T ire Section”) • SER VICE TIRE SYSTEM SOON (Refer to “Starting And Operating, T ire Section”) • TIRE PRESSURE UNA V AILABLE (Refer to “Starting And Operating, T ire Section”) • TCS SUSPENDED (T raction Control System, with a graphic and single chime) • TC[...]

Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Y es” or “No.” Auto Unlock On Exit? When this feature is selected all the vehicle’s doors will unlock when the driver’s door is o[...]

flash lights on lock/unlock feature. Pr essing the STEP button when in this display will select “Y es” or “No.” Flash Lights On Lock/Unlock? When this feature is selected, the fr ont and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter . This feature may be selected with or withou[...]

Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the curr ent accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Y es” or “No.” Power Accessory Delay? When this feature is selected, the power window s[...]

Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new , the compass may appear erratic and the EVIC will display “COMP ASS CALIBRA TING” until the compass is calibrated. The compass will calibrate automatically after approximately 40 seconds if no buttons ar[...]

T o set the variance: T urn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no mor e than 10 seconds. The “COMP ASS V ARIANCE” message and the last vari- ance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET [...]

• Of f Mode Shows a blank display . • Step Button Push this button to cycle through all the Mini-trip functions. T o Reset The Display Pressing and r eleasing the Reset button once will clear the resettable function curr ently being displayed. The resettable function is average fuel economy . Reset will only occur if the resettable function is [...]

SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLA YER AND CD/DVD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to opera[...]

top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it. T uning Press the TUNE contr ol up or down to increase or decrease the fr equency . If you press and hold the button, the radio[...]

both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory . Y ou can recall the stations stored in SET 2 memory by pr essing the push- button twice. T o Change From Clock T o Radio Mode Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of[...]

If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If you insert a disc with the ignition OFF , the display will show the time of day for about 5 seconds, then go out. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show th[...]

Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forwar d through the tracks. Pr ess the FF button a second time to stop the fast forward feature. If TUNE R W is pressed, the current track will reverse to the beginning of the track and begin playing. Press the RND button a second time to stop Random Play . CD[...]

Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control to the right to incr ease the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program T ype) Button Pressing this button once will turn on the[...]

Program T ype Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in th[...]

Scan Press and r elease the SCAN button to search for the next station in either the AM or FM mode. The radio will pause for 5 seconds at each listenable station before continuing to the next. T o stop the search, pr ess the SCAN button a second time. T une Press the TUNE contr ol up or down to increase or decrease the fr equency . If you press and[...]

SET 1 will now show in the display window . Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory . Y ou may add a second station to each push-butt[...]

T ape Player Operation Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatur es, the tape mechanism may requir e a few minutes to warm up for proper operation. Sometimes poor playback may be exper[...]

Rewind — R W Press the R W button down momentarily to reverse the tape direction. The tape will r ewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction. EJT T ape Press the EJT T APE button and the cassette will disen- gage and eject from t[...]

CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON befor e the CD player will operate. Inserting The Compact Disc Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio off, the display will show CD and the time of day will be display[...]

FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W (Reverse) button works in a similar manner . Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to [...]

Disc Up/Program Button 1 Press the DISC (button 1) button to play the next avail- able disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play . This feature plays the selections on the currently playing compact disc in random or der to provide an inter esting change of pace. Press [...]

6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED The Rear Seat Audio/V ideo System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through wir eless headphones, while the front seat pas- sengers listen to either AM/FM, Cassette or CDs from the radio speakers. A remote contr ol is provided for func- tions such as changing tracks[...]

T o insert disc(s) into the changer , follow the instructions shown: 1. On vehicles equipped with the pr emium version, select and press any number ed button without an illumi- nated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated. On vehicles equipped with the premium version[...]

• If you insert a disc with the ignition ON and the radio OFF , the DVD will automatically be pulled into the DVD changer and the display will show the time of day . • It is recommended to label home made burned discs with a permanent marker instead of adhesive labels. These types of labels may become loose and cause the disc to be stuck in the[...]

Operating Instructions — Remote Control NOTE: Aim the remote contr ol at the DVD changer located on the center of the instrument panel and pr ess the desired button. Dir ect sunlight or objects blocking the line of sight may affect the function of the r emote control. 178 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

1. Headphone T ransmitter 2. Menu Up/Next T rack/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Pr evious Disc 1 1. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous T rack/Chapter 16. Menu Right/Fast Forward 17. Enter 18. Light Headphone T ransmitter Button (1)[...]

SETUP Button (5) This button only functions in DVD video mode. Press the button after pressing the ST OP button to access the DVD changer set up menu. Use the right and left arrows to move between tabs for language, rating, mark, audio and aspect. Use the up and down arrows to move between options within each tab. T o change an item highlighted in [...]

STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD. MENU Button (14) This button only functions in DVD video mode. Press this button to select the DVD disc menu. NEXT/PREV Buttons (2, 15) Press the up arr ow or the NEXT button for the next chapter or track on the disc. Press the down arr ow or PREV butt[...]

Operating Instructions — Video Screen Push up on the release button to lower the video scr een. 1. Screen W idth Button Changes the width of the screen pictur e. 2. Enter Button This button will enter the selection from the on-screen menu. 182 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

3. Brightness Button Changes the brightness of the screen pictur e. Operating Instructions — Headphones 1. Power Button 2. V olume Control 3. Power Indicator UNDERST ANDING YOUR INSTRUMENT P ANEL 183 4[...]

Power Button Pressing the power button will turn the headphones ON/OFF . An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in ap- proximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned of[...]

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference r eceived, including interference that may cause undesired operation. If you do not hear soun[...]

NOTE: MP3 player’s, video game systems, camcorders connected to the RCA jacks and CD’s or DVD’s inserted into the CD/DVD changer can be heard thr ough the headphones. SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to r eceiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription se[...]

ESN/SID mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed since any button was pushed. ESN/SID Access W ith RBP , RBU, RAZ, and RBQ Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers wi[...]

Selecting a Channel Press and r elease the SEEK or TUNE buttons to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and r elease the SCAN button (if equipped) to automatically change chan[...]

NOTE: Pressing the ⬙ SEEK ⬙ or ⬙ SCAN ⬙ button while performing a music type scan will change the channel by one and stop the search. Pr essing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button wi[...]

REMOTE SOUND SYSTEM CONTROLS The remote sound system contr ols are located on the r ear surface of the steering wheel at the 3 and 9 o’clock positions. The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system. Pressing the top of the r ocker switch will increase the volume and pressing the [...]

CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play . If you press the switch up or down twice it plays the second track, thre[...]

AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the r eception relatively clear , which is the major feat[...]

Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition is low or “muddy” sound from one or both chann[...]

RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your radio performance does not satisfactorily “cle[...]

T o replace the navigation map DVD lift the storage bin cover and liner in the rear car go area, pr ess the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit. CLIMA TE CONTROLS The Air Conditioning and Heating System is designed to mak[...]

regulates the heating and air conditioning system includ- ing blower speed, outlet air temperature, and airflow distribution through the various outlets within the in- strument panel. Using the ⬙ TEMP ⬙ buttons, adjust the temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to cha[...]

• The “DELA Y” symbol will flash to indicate that the feature as been disabled. This feature may be enabled using the following pr oce- dure: • Press and hold the Heated Rear W indow and Auto HI buttons for 5 seconds. • The “DELA Y” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the enti[...]

The front blower contr ol can be set to any fixed blower speed by pressing the r ocker switch up or down. This allows the front occupants to contr ol the volume of air circulated in the vehicle and cancel the auto mode. The fan will now operate at a fixed speed until additional speeds are selected or until either the ⬙ AUT O HI ⬙ or ⬙ AUTO LO[...]

Bi-Level Mode Air comes from both the instr ument panel outlets and floor outlets. A slight amount of air is also dir ected through the defr ost and side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Air com[...]

Mix Mode Air comes from the floor , defrost and side window demist outlets. This mode is not used when operating in either ⬙ AUTO HI ⬙ or ⬙ AUT O LO ⬙ . This mode should be used when airflow to the floor and windshield is desired. Defrost Mode Air comes from the windshield and side window demist outlets. Use this setting when necessary to d[...]

NOTE: While operating in ⬙ AUTO HI ⬙ or ⬙ AUT O LO ⬙ , the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Depress the “A/C” button to turn on and of f the air conditioning during manual operation only . Cool dehumidified air[...]

key is turned “ON”. The frequent use of outside air will help keep odors from building up within the air conditioner-heater housing. It is r ecommended that the recir culation mode be used as little as possible, especially in humid climates. For hot and dry climates, or people who are aller gic to pollen and find frequent use of the r ecirculat[...]

When the A TC display reads ⬙ REAR AUTO ⬙ or when the rear fan is of f, the switch located in the center console between the second row seats is not functional. When the A TC display reads ⬙ REAR ⬙ , only the r ear seat occupants can control the r ear fan speed from the rear switch. When in the “REAR” mode, the rear occupants can set th[...]

W indow Fogging V ehicle windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C button to reduce the humidity inside the vehicle. Fogging on the inside of the windshield can be quickly removed by pr essing the defrost button and incr easing the blower speed. Do not use the Recirculation mode without th[...]

Electric Rear Window Defroster Press this button to turn on the r ear window defroster and the heated side mirr ors. A light in the button will illuminate to indicate the rear window defroster is ON. The defr oster automatically turns off after about 10 minutes of operation. CAUTION! T o avoid damaging the electrical conductors of the rear window d[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 1 0 ▫ Normal Starting ...................... 2 1 0 䡵 Engine Block Heater — If Equipped ......... 2 1 2 䡵 Automatic T ransmission .................. 2 1 3 ▫ Brake/T ransmission Interlock System ....... 2 1 3 ▫ Automatic T ransmission Ignition Interlock Sys[...]

▫ T ire Markings ........................ 2 2 4 ▫ T ire Identification Number (TIN) .......... 2 2 8 ▫ T ire Loading And T ire Pressur e ........... 2 2 9 䡵 T ires—General Information ................ 2 3 3 ▫ T ire Pressur e ......................... 2 3 3 ▫ T ire Inflation Pressur es ................. 2 3 4 ▫ Radial-Ply T ires ....[...]

▫ Gasoline/Oxygenate Blends .............. 2 4 9 ▫ MMT In Gasoline ..................... 2 4 9 ▫ Sulfur In Gasoline ..................... 2 5 0 ▫ Materials Added T o Fuel ................ 2 5 0 ▫ Fuel System Cautions .................. 2 5 1 ▫ Carbon Monoxide W arnings .............. 2 5 1 䡵 Adding Fuel .......................... 2 5 [...]

ST ARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. W ARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause seri[...]

W ARNING! • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transmission cannot be started this way . Un- burned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a dis- charged battery , booster cables may be[...]

If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor , the “NORMAL ST ARTING” pr ocedure should be repeated. After Starting The idle speed will automatically decrease as the engine warms up. ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms engine coolant a[...]

AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, P ARK, or [...]

Automatic T ransmission Ignition Interlock System This system prevents the key fr om being removed unless the shift lever is in P ARK. It also prevents shifting out of P ARK unless the key is in the ACCESSOR Y or ON position. NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is[...]

NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Y our dealer has diagnostic equip- ment to determine if the problem could r ecur . If the transmission cannot be reset, dealer service is requir ed. Gear Ranges DO NOT race the engine when shifting from P ARK or NEUTRAL posi[...]

AUTOSTICK Autostick is a driver-interactive transmission that of fers manual gear shifting capability to provide you with mor e control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with mor e control during passing, city d[...]

• Y ou can start out in first, second, or third gear . Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions. • While in the Autostick mode, Speed Control wi[...]

CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. P ARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on. NOTE: This light only shows[...]

The parking brake should always be applied when the driver is not in the vehicle. W ARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever . Don’t leave the keys in the ignition[...]

Anti-Lock Brake System The Anti-Lock Brake System pr ovides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to pr event wheel lock-up. W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accide[...]

The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light r emains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed. However , t[...]

• and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. W ARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interfer- ence can cause [...]

CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the power steering pump may occur . TRACTION CONTROL — IF EQUIPPED The T raction Control System r educes wheel slip and maintains traction at the driving (front) whee[...]

NOTE: • The T raction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of T raction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster . This is to prevent over heating of the brake system and is a normal condition. The system will re[...]

NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the sidewall[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards L T = Light T ruck tire based on U.S. design standards T = T emporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = Aspe[...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your [...]

4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size and cold tire inflation pressur es specified on[...]

passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400–750 (5 x 150) = 650 lb.) 5. Determine the combined weight of luggage and car go being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a [...]

232 ST ARTING AND OPERA TING[...]

W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory ope[...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption. 3. Ride Comfort and V ehicle Stability?[...]

check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which coul[...]

T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important. Increased tir e pressur e and reduced vehicle loading may be requir ed for [...]

Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial [...]

Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spar e tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car[...]

W ARNING! The limited use spare tires are for emergency use only . Installation of this limited use spare tire affects vehicle handling. W ith this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly . Replace (or repair) th[...]

T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent gr ooves, the ti[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredict- able handling and stress to steeri[...]

Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . ALL WHEEL DRIVE (A WD) — IF EQUIPPED CAUTION! All Wheel Drive (A WD) vehicles must have the same size and type tires on all wheel positions. Unequal tir[...]

1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pr essure levels of 25 psi [1.72 bars] (172 kPa) or less detected in one or more tir es. Inspect all tires for pr oper inflation pressur e, once the proper tir e pressur e has been set, the TPM system warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 20 mph[...]

CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sen- sor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sen[...]

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration. The tire pr essure sensors [...]

CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain br[...]

Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving, and braking functions. For the[...]

FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sions regulations and pr ovide satisfactory fuel economy and performance when us- ing high quality unleaded gasoline having an octane range of 87 to 89 or higher . The manufacturer r ecommends the use of 89 octane for optimum performance. Light spark knock at low engine speeds is not har[...]

Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are r equired in some ar eas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing [...]

MMT is prohibited in Federal and California r eformu- lated gasolines. Sulfur In Gasoline Y our vehicle may have been designed to meet California low emission standards when using cleaner burning California reformulated gasoline with low sulfur . This vehicle may be sold nationwide. Y our vehicle will oper- ate satisfactorily on fuels meeting Feder[...]

Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law . Using leaded gasoline can impair engine performance, damage the emission control system, and could r esult in loss of warranty coverage. • An out-of-tune engine, or certain fuel or ignition malfu[...]

• Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed ar ea, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine r unning for more than a short period, adjus[...]

CAUTION! T o avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: • T ighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. If the gas cap is not secured pr operly the Mal[...]

VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow . This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying car go, do not exceed the specified GVWR and GA WR. V ehicle Certification Label Y our vehicle has a certification label attached to [...]

W ARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of y[...]

A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GA WR capacities have been exceeded. Example Only Front Axle Rear Axle Empty W eight 2538 lbs (1 151 kg) 2076 lbs (942 kg ) Load (Including driver , pass- sengers and cargo) 223 lbs (101 kg) 890 lbs (404 kg) T otal 2762 lbs (1253 kg) 2968 lbs (1346 kg) GA WR 2826 lbs ([...]

Perform maintenance services as prescribed in the main- tenance schedules manual. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GA WR) by the addition of: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. • Remember that everything pu[...]

• The automatic transmission fluid and filter should be changed if you REGULARL Y tow a trailer for mor e than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transmission fluid change intervals. NOTE: • Check the automatic transmission fluid level before towing. Fluid discoloration, or a burnt odor , sh[...]

A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg) and requir ed for weights above 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , hi[...]

[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 2 6 2 䡵 If Y our Engine Overheats ................. 2 6 3 䡵 Jacking And T ire Changing ................ 2 6 4 ▫ Jack Location ........................ 2 6 5 ▫ Spare T ire Stowage .................... 2 6 5 ▫ Preparations For Jacking ................ 2 6 6 [...]

HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel. When the Hazar d W arn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traf fic of an emer[...]

IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appr opriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed. NOTE: There ar e steps that you can take to slow down an impendi[...]

W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKIN[...]

Jack Location The jack and jack-handle are stowed in the r ear storage bin located in the rear car go floor . Pull up on the storage bin cover and liner to access the jack and jack tools. Spare Tire Stowage The spare tir e is stowed under the rear of the vehicle by means of a cable winch mechanism. T o remove or stow the spare, use the jack handle [...]

Spare T ire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the gr ound with enough slack cable to allow you to pull the tire out fr om under the vehicle. CAUTION! The winch mechanism is designed for use with the jack handle only . Use of an air wrench or other power tools is not recommended and can [...]

• Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove the spar e wheel, scissors jack and jack-handle from stowage. 2. Car efully pry off the wheel center cap using the tip of the jack handle. 3. Loosen (but do not r emove) the wheel lug nuts by turning them to the left one turn while the w[...]

location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack scr ew to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tir [...]

W ARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. 12. Secur e the flat or spare tire as follows: • The center cap of a cast aluminum wheel must be removed prior to flat tir e stowage. Store the center cap i[...]

JUMP-ST ARTING PROCEDURES IF BA TTER Y IS LOW W ARNING! T ake care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. Y ou can be hurt by the fan. 270 WHA T TO DO IN EMERGENCIES[...]

W ARNING! • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be u[...]

5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery . Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery , let the engine idle a few minutes, then start the engine in the vehicle with the dis[...]

2. Slow down if r oad has standing water or puddles. 3. Replace tir es when tread wear indicators first become visible. 4. Keep tir es properly inflated. 5. Maintain suf ficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow , i[...]

TOWING A DISABLED VEHICLE With Ignition Key Front Wheel Drive Y our vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and r ear wheels must be on the ground. Exceeding these tow[...]

All T ransmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck. • Do not tow the vehicle from the rear . Damage to the rear s[...]

TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Flat towing of vehicles equipped with an automatic transmission, is only permitted within the limitations described in this section. TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A T OW DOLLEY The manufacturer does not recommend that you tow an All-Wheel D[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 3.5L Engine ........................... 2 8 0 䡵 Onboard Diagnostic System — OBD II ........ 2 8 1 䡵 Emissions Inspection And Maintenance Programs ............................ 2 8 2 䡵 Replacement Parts ...................... 2 8 3 䡵 Dealer Service ......................... 2 8 3 䡵 Maintenance Proced[...]

▫ Steering Shaft Seal .................... 2 9 5 ▫ Steering Linkage ...................... 2 9 5 ▫ Drive Shaft Universal Joints .............. 2 9 5 ▫ Body Lubrication ..................... 2 9 6 ▫ W indshield W iper Blades ................ 2 9 6 ▫ W indshield And Rear W indow W ashers ..... 2 9 7 ▫ Exhaust System ....................[...]

▫ Front Park/T urn Signal And Sidemarker Lights ............................. 3 2 2 ▫ Front Fog Light ...................... 3 2 3 ▫ Rear T ail, Stop, T urn Signal, Side Marker And Back-Up Lights ....................... 3 2 4 ▫ License Light ........................ 3 2 4 䡵 Fluids And Capacities ................... 3 2 5 䡵 Recommended F[...]

3.5L ENGINE 280 MAINT AINING YOUR VEHICLE[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system. Failure to pass could pr event vehicle registration. For states which have an I/M (Inspection and Maintenance) requir ement, this check verifies the following: the MIL (Malfunction Indi[...]

ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M stat[...]

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take yo[...]

The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or befor e starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding [...]

Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures ar e below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles [...]

American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only r ecommends API Certified engine oils. Engine Oil V iscosity Chart The proper SAE viscosity grade of engine oil should be selected based on the following recommendatio[...]

Synthetic Engine Oils Y ou may use synthetic engine oils provided that the recommended oil quality r equirements ar e met and the recommended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacture str ongly recommends against the addi- tion of any additives (other than leak detection dyes) to th[...]

Also check belt routing to make sur e there is no interfer - ence between the belts and other engine components. Spark Plugs Spark plugs must fire pr operly to assure engine perfor - mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if ther e is any malfunction due to a faulty sp[...]

Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assur e prope[...]

W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual situations involving grossly malfunctioning engine o[...]

W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water . • Battery gas is flammable and explosive. Ke[...]

Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. W ARNING! • Use only refrigerant[...]

Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and r ecycling equ[...]

W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid f[...]

Continued operation could result in failur e of the univer- sal joint due to water and dirt contamination of the grease. This would r equire complete r eplacement of the joint assembly . Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure[...]

Windshield and Rear Window W ashers The fluid reservoir for the windshield washers and the rear window washer is shar ed. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the r eservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush o[...]

damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for br oken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil[...]

Coolant Checks Coolant protection checks should be made every 12 months (prior to the onset of freezing weather , where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fr esh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty , clean by g[...]

CAUTION! • Mixing of coolants other than the specified HOA T coolant may result in decreased corrosion protec- tion and engine damage that may not be covered under the new vehicle warranty . If a non-HOA T coolant is introduced into the cooling system in an emergency , it should be replaced with the speci- fied coolant as soon as possible. • Do[...]

Coolant Pressure Cap The coolant pressur e cap must be fully tightened to prevent loss of coolant, and to insur e that coolant will return to the coolant bottle fr om the overflow tank. The coolant pressur e cap should be inspected and cleaned if there is any accumulation of for eign material on the sealing surfaces. W ARNING! • The warning words[...]

community . T o prevent ingestion by animals or childr en do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately . Clean up any ground spills immediately . Coolant Level The coolant bottle provides a quick visual method for determin[...]

• Maintain coolant concentration at 50% ethylene glycol antifreeze (minimum) in water for pr oper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant bottle hoses are not kinked or obstr ucted. • Keep the front of the radiator and the fr ont of the A/C condenser clean. • Do not c[...]

Brakes In order to assur e brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Schedules. W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnorma[...]

NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and at every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots. If ther e is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take pl[...]

Use only manufacturers r ecommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. W ARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of brake fluid that may have a lower initial boiling point or unident[...]

Care should be taken in installing quick connect fittings to insure they ar e properly installed and fully connected. See your authorized dealer for service. Automatic T ransmission The automatic transmission and differ ential assembly are contained within a single housing. All automatic transmissions are equipped with a conven- tional filler tube [...]

Procedure For Checking Fluid Level The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will gr eatly reduce the life of the transmission and of the fluid. T o properly check the automatic transmission fluid level, the following procedur e must be used: 1. The vehic[...]

b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD”. If the fluid level indicates low , add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage. T o prevent dirt and water from entering the transmission after che[...]

All Wheel Drive (A WD) — If Equipped Under normal operating conditions, periodic fluid level checks and lubricant changes for the Power T ransfer Unit, Overrunning Clutch and Rear Carrier , are not requir ed. However when the vehicle is serviced for other reasons, the exterior surface of these components should be inspected for evidence of fluid [...]

Fluid Changes The fluid should be changed as follows: Normal Usage No Service Requir ed Severe Usage Power T ransfer Unit 15,000 miles (24 000 km) Overrunning Clutch 22,500 miles (36 000 km) Rear Carrier 22,500 miles (36 000 km) Severe Usage is defined as: 1. Mor e than 50% of vehicle operation in stop and go traffic wher e vehicle is driven regula[...]

The following maintenance recommendations will enable you to obtain maximum benefit from the corr osion resistance built into your vehicle. What Causes Corrosion? Corrosion is the r esult of deterioration or removal of paint and protective coatings fr om your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • St[...]

CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the under carriage at least once a month. • It is important that the drain holes in the lower edges of the [...]

• If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Y our dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar V inyl Cleaner to clean vinyl [...]

Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning the inside rear window equipped with electric defrosters or the right r ear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instru[...]

Cleaning The Center Console Cup Holders Removal Grab the center of the rubber portion of the cupholder and lift upward. Cleaning Soak the rubber cupholder liner in a mixtur e of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour . After one hour pull the liner from the water and dip it back into the [...]

Cavity Maxi Fuse Description 1 40 Amp Green Anti-Lock Brake System (ABS) Pump 2 Spare 3 30 Amp Pink Ignition Off Draw (IOD) 4 40 Amp Green Body Control Module (BCM) Feed 1 5 40 Amp Green Electronic Back Light (EBL) 6 30 Amp Pink Fr ont W ipers 7 40 Amp Gr een Starter 8 40 Amp Green Power Seat C/B 9 40 Amp Gr een Power Sunr oof Cavity Maxi Fuse Desc[...]

Cavity Mini Fuse Description 24 20 Amp Y ellow Power Outlet (Selectable) 25 15 Amp Blue Radio, Amplifier , Navi- gation, Hands-Free Phone (HFM), Electronic V ehicle Information Cen- ter (EVIC), EC, SNRF , Mirror 26 20 Amp Y ellow Power Outlet 27 Spare 28 25 Amp Clear Horn 29 20 Amp Y ellow Cluster , CHMSL, Stop Lights, Anti-Lock Brake System (ABS) [...]

CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the [...]

REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Reading Lights ............... 5 7 8 Front Door Courtesy Light .................. 5 7 8 Liftgate Light(s) .......................... 5 7 8 Overhead Console Reading Lights ........... 212–2 V isor V anity Lights ..................... V26377 NOTE: For lighted switches, s[...]

BULB REPLACEMENT Standard Quad Headlights 1. Remove the two scr ews securing the headlight mod- ule to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly fr om the lower attachment clip. 2. Remove the rubber boot seals. 3. Disconnect the electrical connector . 4. Rotate the bulb to the left and r eplac[...]

High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage dischar ge tube. High voltage can remain in the cir cuit even with the headlight switch off and the key r emoved. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authori[...]

2. T wist the bulb socket to remove fr om the headlight module and pull the bulb from socket. 3. Replace the bulb, r einstall the socket and then reinstall the headlight module. Front Fog Light 1. Remove the scr ew from the front of the fog light and pull out from the fr ont of the fascia. 2. T wist the front fog light bulb to r emove from the fog [...]

Rear T ail, Stop, T urn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly scr ews and rotate the assembly outward to r emove the ball stud form the attaching grommet. 3. T wist the socket assembly to remove it fr om the housing. 4. Pull the bulb out of the socket. 5. Replace the bulb, r einstall the[...]

FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 89 Octane 23 gallons 87 liters Engine Oil-W ith Filter 3.5 Liter Engines (SAE 10W -30, API Certified) 5.5 qts 5.2 liters Cooling System * 3.5 Liter Engines (Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula) 10.5 qts 9.9 liters * Includes heater and coolant recovery bottle filled to MAX [...]

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil Use API Certified. SAE 10W -30 is preferred, r efer to oil viscosity chart for correct SAE grade meeting DaimlerChrysl[...]

Chassis Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid. A WD Power T ransfer Unit Mopar 威 Gear Lubricant 75W -90. A WD Overrunning Clutch Mopar 威 A TF+4 Automatic T ransmission Fluid. A WD Rear Carrier Mopar 威 Gear Lubricant 75W -90. Brake Master Cylinder Mopar 威 DOT 3 a[...]

[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 3 0 䡵 Maintenance Schedules ................... 3 3 0 ▫ Schedule “B” ........................ 3 3 3 ▫ Schedule “A” ........................ 3 4 4 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliab[...]

• T axi, police, or delivery service (commercial ser - vice). 〫 • Off-r oad or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙ Maintenance Schedules ⬙ section of this manual. NOTE: Most vehicles are operate[...]

Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. • Check all lights and all other electrical items for correct operation. At Each Oil Change • Ch[...]

SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 . • Day or night temperatures ar e below 32° F (0°[...]

Miles 3, 000 6, 000 9, 000 12, 000 15, 000 18, 000 (Kilometers) (5 000 ) (10 000 ) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * XXXX X Replace the engine air cleaner filter . *X Change the All [...]

Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * XXX X X Replace the engine air cleaner filter . X Inspect the t[...]

Miles 39, 000 42, 000 45, 000 48, 000 51, 000 54, 000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * XX XX X Replace the engine air cleaner filter . *X Change the A[...]

Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * X XXX X Replace the engine air cleaner filter . X Inspect[...]

Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change the All Wheel Drive (A WD) power transfer unit fluid. (See note at the end of this chart) XX Change the All Wheel Drive (A WD) overrun- ning clutch and rear carrier fluid. (See note at the end of this chart) X Replac[...]

Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * XXXX Replace the engine air cleaner filter XX Replace the[...]

Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change the All Wheel Drive (A WD) overrun- ning clutch and rear carrier fluid. (See note at the end of this chart) X Replace the air conditioning filter . X 340 SCHEDULE “B” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter . X X X X X Rotate T ires X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary . * XXXXX Replace the engine air cleaner filter *X Replace e[...]

Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Flush and replace the engine coolant at 60 months or 100,000 miles. X Replace the air conditioning filter . X Miles 108, 000 1 1 1, 000 1 14, 000 1 17, 000 120, 000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (1[...]

Miles 108, 000 1 1 1, 000 1 14, 000 1 17, 000 120, 000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Inspect the serpentine drive belt, replace if neces- sary . ‡ X Change the automatic transmission fluid and filter . X Change the All Wheel Drive (A WD) power transfer unit fluid. (See note at the end of this chart) X Replace the [...]

SCHEDULE “A” Miles 6, 000 12, 000 18, 000 24, 000 30, 000 36, 000 (Kilometers) (10 000) (19 000) (29 000) (38 000 ) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate T ires X XXXXX Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * X XXX [...]

Miles 42, 000 48, 000 54, 000 60, 000 66, 000 72, 000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (115 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X XXXX Rotate T ires X X XXXX Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary . * XX X X X Replace t[...]

Miles 78, 000 84, 000 90, 000 96, 000 100, 000 (Kilometers) (125 000) (134 000) (144 000) (154 000) (160 000) [Months] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X Rotate T ires X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary . * XX X X Replace the engine air cleaner filter [...]

Miles 102, 000 108, 000 1 14, 000 120, 000 (Kilometers) (163 000) (173 000) (182 000) (192 000) [Months] [102] [108] [114] [120] Change engine oil and engine oil filter . X X X X Rotate T ires X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary . * X X X Replace the engine air cleaner filter . X Replace[...]

* This maintenance is recommended by the manufactur e to the owner but is not requir ed to maintain the emis- sions warranty . ‡ This maintenance is not requir ed if previously r eplaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. W ARNING! Y ou can be badly injured worki[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 5 0 ▫ Prepar e For The Appointment ............ 3 5 0 ▫ Prepar e A List ........................ 3 5 0 ▫ Be Reasonable W ith Requests ............. 3 5 0 䡵 If Y ou Need Assistance ................... 3 5 0 䡵 [...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

The manufacturer has empower ed its dealers to make warranty and repair decisions that ensur e you are not inconvenienced. There is no need for you to wait for a decision from the manufactur er . If a special circumstance occurs that requir es information from the manufactur er , we have asked the dealer’s service management to make the contact o[...]

Mexico, D. F . In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any heari[...]

W e appreciate that you have made a major investment when you purchased your new vehicle. Y our dealer has also made a major investment in facilities, tools, and training to assure that you ar e absolutely delighted with your ownership experience. Y ou’ll be pleased with their sincere ef forts to resolve any warranty issues or r elated concerns. [...]

354 IF YOU NEED CONSUMER ASSIST ANCE[...]

MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immedi[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A str eet address is requir ed when ordering manuals. (No P .O. Boxes). •[...]

Call T oll Free at 1–800–890–4038 (U.S.) or 1–800–387–1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .daimlerchrysler .com or www .daimlerchrysler .ca/manuals DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway [...]

W ARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. T emperature Grades The temperature grades ar e A (highest), B, and C, repre- senting the tire’s r esistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on [...]

INDEX 10[...]

Adding Fuel ........................... 2 5 2 Adding W asher Fluid .................. 1 15,297 Additives, Fuel ......................... 2 5 0 Adjustable Pedals ........................ 1 1 8 Air Conditioner Maintenance ............... 2 9 3 Air Conditioning Filter ................. 204,294 Air Conditioning Refrigerant ............... 2 9 3 Air Con[...]

Selection Of Lubricant ................ 307,327 Shifting ............................. 2 1 5 Special Additives ...................... 3 0 9 Autostick ........................ 120,215,216 Ball Joints ............................. 2 9 5 Battery ............................... 2 9 1 Jump Starting ......................... 2 7 0 Keyless T ransmitter Re[...]

Catalytic Converter ...................... 2 9 0 Caution, Exhaust Gas ................... 60,297 CD Changer ...................... 165,173,175 CD Player .................. 161,163,165,172,175 CD Player Maintenance ................... 1 9 3 Cellular Phone ........................ 71,194 Chains, T ire ............................ 2 4 5 Changing A Fla[...]

Cruise Contr ol .......................... 1 1 9 Cruise Light ........................... 1 4 9 Cup Holder ......................... 133,316 Customer Assistance ..................... 3 5 0 Dealer Service .......................... 2 8 3 Defroster , Rear W indow ................... 2 0 5 Defroster , W indshield ................... 61,200 Delay W ipe[...]

Block Heater ......................... 2 1 2 Break-In Recommendations ................ 5 9 Checking Oil Level ..................... 2 8 4 Compartment ......................... 2 8 0 Coolant ............................. 3 2 6 Cooling ............................. 2 9 8 Exhaust Gas Caution .................. 29,251 Fails to Start ...................[...]

Fog Light Service ........................ 3 2 3 Fog Lights ....................... 1 12,150,323 Folding Rear Seat ........................ 1 0 1 Freeing A Stuck V ehicle ................... 2 7 3 Fuel ................................. 2 4 8 Adding ............................. 2 5 2 Additives ............................ 2 5 0 Clean Air ..........[...]

Head Phones ........................... 1 8 3 Head Restraints .......................... 9 4 Headlights ............................ 3 2 2 Bulb Replacement ...................... 3 2 1 High Beam ........................... 1 1 3 High Beam/Low Beam Select Switch ........ 1 1 3 Passing ............................. 1 1 3 Replacing ...................[...]

Key , Programming ........................ 1 4 Key , Replacement ........................ 1 4 Key , Sentry ............................. 1 2 Key-In Reminder ......................... 1 2 Keyless Entry System ...................... 1 9 Keys .................................. 1 1 Knee Bolster .......................... 46,48 Lap/Shoulder Belts ......[...]

Oil Pressur e .......................... 1 5 0 Park ............................... 3 2 2 Reading ............................. 1 2 2 Rear Servicing ........................ 3 2 4 Rear T ail ............................ 3 2 4 Seat Belt Reminder ..................... 1 5 0 Service ........................... 320,321 Service Engine Soon .............[...]

Mini-T rip Computer ...................... 1 5 9 Mirrors ................................ 6 7 Automatic Dimming ..................... 6 7 Electric Remote ........................ 6 9 Exterior Folding ........................ 6 8 Heated .............................. 7 0 Memory ............................. 1 0 4 Outside ............................[...]

Overhead T ravel Information Center .......... 1 2 2 Overheating, Engine ................... 144,263 Owner’s Manual ....................... 4,356 Panic Alarm ............................ 2 1 Parking Brake .......................... 2 1 8 Parking On Hill ......................... 2 1 8 Passing Light ........................... 1 1 3 Pedals, Adjust[...]

Radio, Satellite .......................... 1 8 6 Rear Liftgate ............................ 2 6 Rear Seating Flexibility .................... 1 0 1 Rear W indow Defroster ................... 2 0 5 Rear W indow Features .................... 1 1 4 Rear W iper/W asher ...................... 1 1 4 Rearview Mirrors ........................ 6 7 Reclinin[...]

Adjustable Upper Shoulder Anchorage ........ 3 6 And Pregnant W omen ................... 4 1 Child Restraint ......................... 5 1 Extender ............................. 4 1 Front Seat ............................ 3 1 Pretensioners .......................... 3 9 Rear Seat ............................. 3 1 Reminder ..........................[...]

Starting and Operating .................... 2 1 0 Starting Procedur es ...................... 2 1 0 Steering Linkage ............................. 2 9 5 Power ........................... 222,294 Shaft Seal ............................ 2 9 5 T ilt Column .......................... 1 1 6 Steering Wheel Mounted Sound System Controls ..................[...]

Changing ............................ 2 6 4 Compact Spare ........................ 2 3 7 General Information .................... 2 3 3 High Speed .......................... 2 3 6 Inflation Pressur es ..................... 2 3 4 Jacking ............................. 2 6 4 Load Capacity ..................... 229,230 Pressur e Monitor System ........[...]

T ransporting Pets ........................ 5 9 T read W ear Indicators .................... 2 4 0 T rip Odometer .......................... 1 4 8 T rip Odometer Reset Button ................ 1 4 8 T urn Signals ................... 1 12,145,322,324 Uniform T ire Quality Grades ................ 3 5 7 Universal Joints ......................... 2 9 5 [...]

W indshield W ipers ....................... 1 1 3 W iper Blade Replacement .................. 2 9 6 W iper , Rear ............................ 1 1 4 W ipers, Intermittent ...................... 1 1 4 376 INDEX[...]