Cisco Systems OL-27407-01 manuel d'utilisation

Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco we bsite at www.cisco.com/go/ offices. Cisco 80 0 S eries Integrated S ervices Router Hardw are Installation Guide Last R evised: April 8 , 20 1 4 Text Part Number: OL -27407-01[...]

THE SPECIFICATION S AND INFORMAT ION RE GARDIN G TH E PRODU CTS IN THIS MANU AL A RE SUBJ ECT T O CHAN GE W ITHOUT N OTICE. ALL STATEMENTS , INFORMATION , AND RECOMMEN DATIONS I N THIS MANUA L ARE BELIEVE D TO BE ACCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED. USER S MUST TAKE FULL RESPONSI BILITY FOR THEIR APPLICAT I[...]

Contents 1 Cisco 800 Series Integrated Services Router Hardware Installa tion Guide OL-27407-01 Preface vii Objective vii Audience vii Organization viii Conventi ons viii Related Documentation xvi Searching Cisco Documents xvi Obtaining Documentation and Submitting a Serv ice Request xvi Product Overview 1-1 Cisco 810 Series 1-1 Cisco 812 Series 1-[...]

Contents 2 Cisco 800 Series Integrated Services Router Hardware Installation Guide OL-27407-01 Cisco C886VA Router 1-59 Cisco C886 VA J Router 1-60 Cisco C887VA Router 1-61 Cisco C887VAM Router 1-62 Cisco 890 Series ISRs 1-63 Cisco 891, Cisco 892, and Cisco 892F 1-63 Cisco C891 Series ISR s 1-73 Cisco C891F Router 1-74 Cisco C891 F W Router 1-75 Ha[...]

Contents 3 Cisco 800 Series Integrated Services Router Hardware Installa tion Guide OL-27407-01 Installing on a Table 2-38 Mounting on a Wall 2-38 Installing the Router Ground Connection 2-41 Installing the FIPS Cover 2-41 Installing Antennas for Cisco 890 Series 2-45 Installing Cisco 890 Series in a Rack 2-49 Installing the C881G-B/S/V-K9 ISR 2-51[...]

Contents 4 Cisco 800 Series Integrated Services Router Hardware Installation Guide OL-27407-01 Connecting an xDSL Line 3-31 Connecting Power over Ethern et 3-34 Connecting the AC Adapte r 3-35 Connecting an FXS Line 3-39 Connecting an FXO Line 3-4 0 Connecting a Voice ISDN BRI Line 3-42 Verifying Connections 3-45 Initial Configuration 4-1 Cisco 810[...]

Contents 5 Cisco 800 Series Integrated Services Router Hardware Installa tion Guide OL-27407-01 Power Supply A-22 Wireless Access Poin t A-22 FE and GE Port Pinouts A-2 3 Console and Auxiliary Port Connector Pinouts A-24 FXS and FXO Port Connector Pinouts A-24 VDSL2 Port Connector Pinouts A-24 ADSL2+ Port Connector Pinouts A-25 V.92 Port Connector [...]

Contents 6 Cisco 800 Series Integrated Services Router Hardware Installation Guide OL-27407-01[...]

vii Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Preface This preface describes the objectiv es , audience, organizatio n, and con ventions of this guide and describes related docu ments that ha ve additional information. It contains the follo wing sections: • Objecti ve, page vii • Audience, pag e vii • Org anizat[...]

viii Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Organization This guide is or ganized into the follo wing chapters and appendi x. Conventions This section describes the con ventions used in this guide. Note Means reader take note . Notes contain helpful suggestions or referen ces to additional informat ion and materia[...]

ix Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 War ni n g IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means danger . Y ou are in a situation that could cause bodily inju ry . Before you work on any equipment, be aware of the haza rds involved with electrical circuitry and be fam iliar with standard practices for [...]

x Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Avvertenza IMPORT ANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qua lsiasi apparecchiatura, occorre essere al corrente dei pe ricoli relativi ai circuiti elet t[...]

xi Cisco Integrated Services Router Hardware Installation Guide OL-27407-01[...]

xii Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo. V ocê se encontra em uma situação em que há risco de lesõe s corporais. Antes de trabalhar com qualquer equipam ento, esteja ciente do s risc os que envolvem os circuitos elétric[...]

xiii Cisco Integrated Services Router Hardware Installation Guide OL-27407-01[...]

xiv Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 War ni n g When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using a ny other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-ce rtified [...]

xv Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 War ni n g If the symbol of suitabilit y with an overla id cro ss appe ars above a port, you must no t con nect the port to a public network tha t follows the European Uni on standards. Connecting the port to this type of public network can cause severe personal injury or c[...]

xvi Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 War ni n g Read the installation instruc tions before connecting the system to the power sou rce. Statement 1004 War ni n g Ultimate disposal of this product should be han dled according to al l national laws and regulations. Statement 1040 War ni n g The covers are an in[...]

xvii Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Subscribe to the What’ s New in Cisco Pr oduct Documentation as a Really Simple S yndication (RSS) feed and set content to be deliv ered directly to your deskto p using a reader applicatio n. The RSS feeds are a free service and Cisco currently supports RSS V ersion 2.0[...]

xviii Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01[...]

CH A P T E R 1-1 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 1 Product Overview This chapter provides an overview of the features a vailable for the Cisco 812, Ci sco 819, Cisco 860, 880, 890 Integ rated Services Router (ISR) and contains the follo wing sections: • Cisco 810 Series, page 1-1 • Cisco 860, 880, 890 Se[...]

1-2 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series The 3rd Generation (3G) is a generation of stand ards for mobile technology that f acilitates gro wth, increased in bandwidth, and supports more di verse application s. The Cisco 812 ISR can be po wered by an (includ ed) e x te[...]

1-3 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Figure 1-2 sho ws the 3G antenna and LEDs display . Figur e 1 -2 Cisco 812 ISR 3G and LEDs Displa y 1 2 4 3 344400 1 3G di versi ty antenna 3 Wi F i L E D 2 3G main an tenna 4 3G LED[...]

1-4 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Figure 1-3 sho ws the I/O side of the Cisco 812 ISR. Figur e 1 -3 Cisco 812 IS R I/O Side Hardware Features The Cisco 812 ISR supports the f ollow ing hardware features: • Platform Features, page 1-4 • Antenna, page 1-5 •[...]

1-5 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es • Ceiling and W all Mounting O ption • LED indicators for the platform Antenna The Cisco 812 ISR supports 3G e xternal antenna and W iFi embedded antenna. 3G External Antenna The Cisco 812 ISR pro vides two standard panel-m[...]

1-6 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series RSSI 1 White, Green, Light Blue, or Blue (solid) Signal > –60 dBm V ery strong signal White, Green, Light Bl ue, or Blue (three blinks and then a long pause ) Signal <= –60 to 74 dBm Strong signal. White, Green, Light[...]

1-7 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Ta b l e 1 - 2 describes the W iFi LED for the Cisco 812 ISR. T able 1 -2 Cisco 812 ISR WiFi LED De scr iptions Message T ype Color Description Boot loader status sequence Blinking Green DRAM memory test in prog ress. DRAM memo[...]

1-8 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Memory The Cisco 812 ISR supports 512 MB DRAM and 512 MB compact flash memory . The Host router software runs on the f irst core. The second core runs the WLAN Access Point software. If WLAN is not supported in an SK U, all 512[...]

1-9 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Figur e 1 -4 P oE+ Split ter I/O Side SKU Information Ta b l e 1 - 3 lists the dif ferent SKU s av ai lable for the Cisco 812 ISR. The AP 802-AGN -X-K9 (WLAN PID) is inte grated as part of the router for the SKUs th at support [...]

1-10 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Cisco 819 Series This section prov ides an o vervie w of the features av ail able for the Cisco 819 and Cisco 819H Inte grated Services Routers (ISRs) and con tains the follo w ing sections: • General Descript ion, page 1-10[...]

1-11 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es than replacing a wired LAN withi n a buildin g or campus. WLANs use radio frequen cy to tran smit and recei ve data o ver the air , minimizing the need for wired connections. Figu re 1-6 sho ws the Cisco 819HGW ISR. The WLAN f[...]

1-12 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Figur e 1 -6 Cisco 819HGW Int egrated Services Router Figure 1-7 sho ws the front panel details of the Cisco 819HG ISR. Figur e 1 -7 Cisco 819HG ISR F ront P anel 285479 245547 1 4 3 6 7 9 10 11 12 5 8 2 1 3G main an tenna 7 F[...]

1-13 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Figure 1-8 shows the front p anel details of the Cisco 819HGW ISR. Figur e 1 -8 Cisco 819HGW ISR Fr ont Panel 4 3G mini-USB diagno stic port 10 5 VDC mole x po wer input 5 Div ersity /GPS an tenna 11 Power switch 6 12-in-1 ser[...]

1-14 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Figure 1-9 sho ws the front panel details of the Cisco 819 4G L TE ISR. Figure 1 -9 Cisco 819 4G L TE ISR Fr ont P a nel SKU Information Ta b l e 1 - 4 lists the dif ferent 3G SKUs av ailable for the Cisco 819HG and Cisco 819G[...]

1-15 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es C819HG-B-K9 Compact Hardened 3G IOS Ro uter wit h Bharat generic EVDO Re v A based on MC5728V C819G+7-K9 Compact No n-hardened 3G IOS Rout er with Gl obal HSP A + Release 7 based on MC8705 C819G-U-K9 Compact Non-har dened 3G I[...]

1-16 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Ta b l e 1 - 5 lists the dif ferent SKUs a v ailable for the Ci sco 819HGW , Cisco 819H, and Cisco 819HWD ISRs. T able 1 -5 Support e d SKUs for Cisco 81 9HGW , Cisco 81 9 H, and Cisco 819HWD ISRs SKU ID WLAN ID WiFi External [...]

1-17 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Ta b l e 1 - 6 lists the dif ferent 4G L TE SKUs av ailable for the Cisco 819HG and Cisco 819G ISRs. T able 1 -6 Support e d 4G L TE SKUs for the Ci sco 81 9H G-4G and Cisco 819G-4G ISRs SKU ID Mode Operating Regions Frequency[...]

1-18 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Overvi ew Cisco 810 Series Rebranding of C8xx-B and EHWIC-3G-EVDO-B The C881G-B-K9, C819G-B-K9, and EHWIC-EVDO-B (B harat) SK Us are introduced as an umbrella SKU to cov er BSNL, T ata, and Reliance service pro viders in India. Software based mech anism[...]

1-19 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Hardware Features This section provides an overview of the follow ing hardware features fo r the Cisco 819 ISR . • Platform Features f or Cisco 819 ISRs, page 1-19 • Antennas, page 1-21 • Po wer Switch, page 1-21 • Res[...]

1-20 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series 1 GB Compact Flash support in IDE mode (internal) —Y e s Y e s Cisco EnergyW ise Y es Y es — Dual 802.11 a/ b/g/n Radios with Cisco DFS, CleanAir , and Client Link support —Y e s — Embedded 3G modem Ye s Ye s — Embed[...]

1-21 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Antennas The Cisco 819 3G routers pro vide two stand ard panel-mount TNC connectors to support the 3 G antenna and the di versity and GPS e xternal antenna. The main an tenna is used for the pri mary 3G antenna. The second can[...]

1-22 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series A C T Green Network acti vity on FE Switch ports, GE W AN port, 3G cellular interface, and serial interfaces. Off No network activity . WW AN Green Module is po wered on and co nnected but no t transmitting or receiv ing. Gree[...]

1-23 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Ta b l e 1 - 9 describes the WLAN LEDs for the C isc o 819HGW and Cisco 819HWD ISRs. 3G Green (one blink and then a pause ) For 1xR TT , EGPRS, or GPRS service. Green (two blinks and then a pause ) For EVDO, EVDO/1xR TT , or U[...]

1-24 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series Ta b l e 1 - 1 0 describes the 4G L TE LEDs for the Cisco 819 ISR. Boot loader errors Blinking Red and Blue FLASH f ile system f ailure. Blinking Red and Of f Env ironment v ariable failur e. Bad MA C address. Ethernet failure[...]

1-25 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Memory The Cisco 819HG and Cisco 819G ISRs uses non-up gradable flash memory and main memory . The onboard flash memory contains the Cisco IOS software image and th e boot flash contains the R OMMON boot code. Ta b l e 1 - 1 1[...]

1-26 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series Embedded 3G Modem The 3G cellular interf ace is the primary W AN data l ink , but it can also be used as a backup data link. The 3G technology is third-generat ion wid e-area cell ular tech nol ogy that is used in bro ad band [...]

1-27 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Supported Cisco Antennas an d Cables The Cisco 819 ISR pro vides two standard panel-mount TNC con nectors to support the 3G antenna and the di versity and GPS extern al antenna. The main antenn a is used for the primary 3G ant[...]

1-28 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series Ta b l e 1 - 1 4 lists the supported Cisco W iFi antenna for Cisco 819HGW and Cisco 819HWD ISRs. T able 1 -14 Supported Cisco WiFi Antenna Antenna Frequency band(s) Mounting Mechanical IP Rating Peak Gain 2.4 GHz (dBi) Peak Ga[...]

1-29 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Ta b l e 1 - 1 5 lists the Cisco 4G L TE antennas that are supported for use on Cisco 8 19 ISRs. T able 1-15 Supported 4G L T E Antennas Cisco Part Number Description Maximum Gain and Frequency Ranges Description 4G-L TE-ANTM-[...]

1-30 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series Ta b l e 1 - 1 6 to Ta b l e 1 - 1 8 li st the extension ca bles for use w ith 3G, W iFi, and 4G L TE antennas. The tables include the insertion loss information for the ultra-lo w-loss (ULL) LMR 400 exten sion cables. T abl e[...]

1-31 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Seri es Serial Port The Cisco standard High Speed Smart Seri al 12-in-1 connector all ows t he highest flexi bility of connections to various DTE/DC E de vices. The 12-in-1 serial interf ac e pins connect to the FPGA. The FPGA conf ig[...]

1-32 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 810 Series Figure 1 -1 0 12-in-1 Ser ial Por t Power Supply All SKUs requir e a 5 VDC po wer source. Cisco 819HG and Cisco 819G ISRs ha ve a self- locking Mole x mini-f it connector . Cisco 819HGW and Cisco 819HW D ISRs use a 5.5 mm barr[...]

1-33 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series The vehicle po wer adapters may be us ed for fix ed or mobi le installations. The y do not pro vide electri cal isolation; the inpu t nega tiv e is connected to the output neg ati ve (ch assis ground). Input cabl e i[...]

1-34 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Note Some illustrations in this do cument sho w a wirele ss router . Both wireless and nonwireless models are av ailabl e in the Cisco 860 series, Cisco 880 series, an d Cisco 890 series ISRs. Port and feature locati[...]

1-35 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-7 sho ws the front panel details of the Cisco 860 wireless router . Figure 1 -1 1 Fr ont P an el of the Cisco 860 Ser ies Wir eless ISR Figure 1-12 sho ws the back panel details of the Ci sco 861 wireless (8[...]

1-36 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Cisco 860VAE Series ISRs The Cisco 860V AE series ISR s are fi xed-conf iguration data routers. This section describes the features of the products in this seri es. Interfaces Ta b l e 1 - 2 0 describes the interface[...]

1-37 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-13 sho ws the front panel details of the Cisco 866V AE, Cisco 867V AE, Cisco 866V AE-K9, and Cisco 867V AE-K9 integrated services routers (I SRs). Figure 1 -13 Fr ont Panel of the Cisco 860V AE ser ies ISR F[...]

1-38 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Figure 1-15 sho ws t he back pa nel detai ls of the Cis co 867V AE-K9. Figure 1 -15 Back P a ne l of the Cisco 867V AE-K9 ISR Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs This section pr[...]

1-39 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Common Features The follo wing ke y features are common to each of these router models: • Dual W AN interface (Gigabit Ethernet [GE] and dual-mode ADSL2+ /VDSL2) • 2.4 GHz wireless LAN (WLAN) interface • Fi ve [...]

1-40 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Note For the Cisco C867V AE-POE-W -A-K9, Power -ov er-Ethernet (PoE) is a vail able using port FE0, with a 60-W po wer supply . USB Interface The USB 2.0 interface enables: • T ransferring data usin g a USB flash t[...]

1-41 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series LED Indicators on Front Panel The front panel includes seve ral LED indicators. Figure 1-17 shows the location of the LED indicators. Figure 1- 17 Fr ont P anel LED Indica tors 1 LED indicators 346497 Ci s co 8 60 Se[...]

1-42 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Ta b l e 1 - 2 5 describes the LED indicators. Cisco 880 Series ISRs The Cisco 880 series ISRs ha ve data and v oice capabilities . They hav e the follo wing features: T able 1 -25 Fr ont P anel LED Indicat ors LED L[...]

1-43 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series • Integrated 4- port 10/100 Ethe rnet switch for connecting to the LAN • 10/100 FE, VDSLoPO TS, ADSL over PO TS, ADSL ov er ISDN, DSL Multi-mode (VDSL/ADSLoPO TS, VDSL/ADSLoISDN Cisco V A models on ly), or G.SHDS[...]

1-44 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Figure 1 -18 Fr ont Panel of the Cisco 880 Ser ies Wir eless Data Router Figure 1-19 sh ow s the back panel details of the Cisco 886V A data router . Figure 1 -19 Back P ane l of the Cisco 886V A Router 1 LEDs 3 USB [...]

1-45 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-20 sh ows the b ack panel details of the Cisco 887V A and 886V A-M data router . Figure 1 -20 Back P anel of th e Cisco 887V A and 887V A -M Router Figure 1-21 sho ws the back panel details of the Cisco 888 [...]

1-46 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Cisco 880 Series Voice and Data Routers The Cisco 880 series voice and data routers pr ovide both voice and data ports. The voice ports ma naged voice services that interface with F oreign Exchange Station (FXS), F o[...]

1-47 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-22 sh ows the fr ont panel details of the Cisco 881 SRST and Cisco 888 SRST wireless v oice router . Figure 1 -22 Fr on t Panel of the Cisco 881 SRST and Cisco 888 SR ST Wir eless V oice Router 1 LEDs 2 USB [...]

1-48 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Figure 1-23 sho ws the back pa nel details of the Cisco 881SR ST -W voice router . Figur e 1 -23 Back P anel of the Cisco C881SRST -W V oice Router 1 Primary W AN port 1 —10/100 FE 1. Depending on the router model,[...]

1-49 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-24 sho ws the back pa nel details of the Cisco 888SR ST -W voice router . Figure 1 -24 Back P anel of th e Cisco C888SRS T -W V oice Router Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Figure 1-25 , Figu [...]

1-50 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Note Configuri ng the codec comple xity sett ing to support se cure calls uses DSP resources, but does not affect the maximum number of suppo rted calls. Figure 1-25 sh ow s the front panel details of the Cisco 881-V[...]

1-51 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-26 sho ws the back panel for the Cisco 887V A-V - W router . The Cisco 887V A-V (non-wireless) router does not ha ve th e antennas on the back panel. Figure 1 -26 Back P anel of the Cisco 887 V A -V Router F[...]

1-52 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Cisco 880 Series with Embedded WLAN Antennas Some Cisco 880W , 880WD, and 880-WD ISRs hav e three embedded WLAN antennas. These ISRs are fix ed-platform routers that: • Provide in te grated VPN, embedded W i-Fi CER[...]

1-53 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series Figure 1-29 sh ow s the back panel details of the C8 87V A-WD-A-K9 and C887V A-WD-E-K9 ISRs. Figure 1 -29 Back P ane l of the C887V A -WD-A-K9 and C887V A -WD-E-K9 ISRs C881WD Figure 1-30 sh ow s the front panel deta[...]

1-54 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 890 Series Figure 1-31 sho ws t he back pa nel details o f the C881W D-A-K9 and C8 81WD-E-K9 ISRs. Figure 1 -31 Back P ane l of the C 881WD-A -K9 and C881WD-E-K9 ISRs C881G-B/S/V-K9 ISRs The C881G-B-K9, C881G-S-K9, and C8 81G-V[...]

1-55 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco 860, 880, 89 0 Series C881G-U-K9 ISRs The C881G-U-K9 ISR is a member of the Cisco 880 seri es data routers. These routers provide inte grated V irtual Pri vate Network (VPN), embedded W i-Fi CER TIFIED™, 802.11b/g/n-compliant wireless A[...]

1-56 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Cisco C881, C886, and C887 Series ISRs Cisco C881, C886, and C887 Series ISRs of fer broa dban d speed and simplif ied management to small businesses, small enterprise branches, and telewo rkers. The Ci s[...]

1-57 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1 -32 Fr ont Panel of the Cisco C881 Router For detailed descriptio n about t he LEDs on the Cisco C880 Series Route rs, see the “LEDs” section on page 1-21 . Ci s co Ci s c o 8 00 Serie s OK OK[...]

1-58 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-33 sho ws the back pane l of the C isco C881 Router . Figure 1 -33 Back P anel of the Cisco C88 1 Router For info rmation on installing t he Cisco C880 Seri es Routers, see : http://www .cisco.co[...]

1-59 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-35 sho ws the back pane l of the C isco C886V A Router . Figure 1 -35 Back P anel of the Ci sco C886V A Router For info rmation on installing Cisco C88 0 Series Routers, see: http://www .cisco.com[...]

1-60 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-37 sho ws the back pane l of the Cisc o C886V AJ Router . Figure 1 -37 Back P anel of the Cisco C88 6V AJ Router For info rmation on installing Cisco C88 0 Series Routers, see: http://www .cisco.[...]

1-61 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-39 sho ws the back pane l of the C isco C887V A Router . Figure 1 -39 Back P anel of the Ci sco C887V A Router For informatio n on installing Cisco C88 0 series routers, see the follo wing link: h[...]

1-62 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-41 sho ws the back pane l of the C isco C887V AM router . Figure 1 -41 Back P anel of the Cisco C88 7V AM Router For info rmation on installing t he Cisco C880 Seri es Routers, see: http://www .c[...]

1-63 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs • DIMM expansi on socket that can accept up to 512 MB of additional memory , for a total of 768 MB system memory in Cisco 891 and 892 series IS Rs, and a t otal of 1 GB system memory in Cisco 892F series[...]

1-64 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-43 sh ow s the back panel details of t he Cisco 892-W rout er . Nonwireless router s do not ha ve RP-TNC antennas or connectors on th e back panel. Some of the features that are shown may not be [...]

1-65 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-44 sho ws the location of the SFP port in a Cisco 892F-W router . Figur e 1 -44 SFP Por t Location in a Cisco 892F -W Router Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA The Cisco 892FS[...]

1-66 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-45 sho ws the back panel of the Cisco 892FSP router . Figure 1 -45 Back P ane l of the Cisco 892FSP Router Figure 1-46 sho ws the front panel of the Cisco 892FSP router . Figure 1 -46 Fr on t Pan[...]

1-67 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-47 sho ws t he back pa nel of th e Cisco 896V A router . Figure 1 -47 Back P ane l of the Cisco 896V A Router Figure 1-48 sh ow s the front panel of the Cisco 896V A and the Cisco 897V A router . [...]

1-68 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-49 sho ws the back pane l of the Cisc o 897V A router . Figure 1 -49 Back P ane l of the Cisco 897V A Router Figure 1-50 sho ws t he back pa nel of th e Cisco 897V AM router . Figure 1 -50 Back P[...]

1-69 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-51 sh ow s the front panel of the Cisco 897V AM router . Figure 1 -51 Fr on t Panel of the Cisco 897V AM Router Figure 1-52 sho ws t he back pa nel of th e Cisco 897V A W router . Figure 1 -52 Bac[...]

1-70 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-53 sh ow s the front panel of the Cisco 8 97V A W and the Cisco 897V AMW router . Figur e 1 -53 Fr ont P anel of the Cisco 897V A W and the Cisco 897V AMW Router Figure 1-54 sho ws the back pane [...]

1-71 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C881, C886, and C887 Series ISRs Figure 1-55 sho ws the back pane l of the Cisc o 898EA rou ter . Figure 1- 55 Back P ane l of the Cisco 898EA Router Caution The primary W AN port is design ed for an RJ-45 connector only . Damage to th e [...]

1-72 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Cisco C891 Series ISRs Cisco C891 Series ISRs are designed to deli ver secure broadband, metro Ethernet, wi reless LAN (WLAN) connecti vity , and business co ntinuity . Cisco C891 Series ISRs also pr ovide a 1 -port Giga[...]

1-73 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Cisco C891F Router Figure 1-57 sh ow s the front panel of the Cisco C891 F Router: Figur e 1 -57 Fr ont P anel of the Cisco C891F Router For detailed descriptio n about t he LEDs on the Cisco C890 Series Route rs, see the[...]

1-74 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Figure 1-58 sho ws the back panel o f the Cisc o C891F Router . Figur e 1 -58 Back P anel of the Cisco C89 1F Router For info rmation on installing t he Cisco C890 Seri es Routers, see: http://www .cisco.com/en/US/docs/r[...]

1-75 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs For detailed descr iption about the LEDs on Cisco C890 Series Rout er , see “LEDs” section on page 1-21 .[...]

1-76 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Figure 1-60 sho ws the back pane l of the Cisc o C891FW Router . Figur e 1 -60 Back P anel of the Cisco C891FW Router For info rmation on installing t he Cisco C890 Seri es Routers, see: http://www .cisco.com/en/US/docs/[...]

1-77 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs • Feature Summary Kensington Lock A K ensingt on security slot i s located on the r outer back panel. T o secure the router to a desktop or other surface, use the K ensington lockdown equipment. Reset Button The Reset b[...]

1-78 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Step 2 Press and hold the Reset b utton until t he system status LED begi ns to flash. T ypically , this occurs within 5 seconds. The router reloads itself after the startup config uration ha s been repl aced with the ne[...]

1-79 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs T o reset the router to the factory def ault configurati on or to load a custom conf iguration f ile, follo w these steps: Step 1 T urn the po wer on. Step 2 Press and hold the Reset b utton until the system status LED b [...]

1-80 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs • For a descriptio n of LEDs for Cisco 860 V AE-W -A-K9, Cisco 860V AE-W -E-K9, and Cisco 860V AE -POE-W -A-K9 ISRs models, see the “Cisco 860V AE-W -A-K9, Cisco 860V AE-W -E-K9, and Cisco 86 0V AE-POE-W -A-K9 ISRs?[...]

1-81 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs WLAN (5 G Hz) Green On—Radio is connected , SSID is configured, and client is associated, but no data is being recei ved or being transmitt ed. Slo w blinking—Radio is con nected, SSID is conf igured, and beacons are [...]

1-82 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Data BRI B2 Green Blinking—B2 channel is recei ving or sending data, or data is passing through ISDN channel 2. — 887, 887V , 888 models 892 models 3G 8 WW AN 9 Green On—Service is established. Slo w Blinking—Sea[...]

1-83 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Ta b l e 1 - 3 0 describes the LEDs for the Cisco 866V AE, Cisco 867V AE, Cisco 866V AE-K9, and Cisco 867V AE-K9 ISRs. 2. LWAPP = Lightweight Acces s Point Protocol . 3. PPP = Point-to-Point Prot ocol. 4. xDSL = General t[...]

1-84 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs GE A CT G reen On —GE W AN interf ace is up. Blinking—GE W A N acti vity (traf f ic in either direction). Of f—De vice is po wered off or G E W AN interface is d own . GE Mode Green On—GE W A N Mode is selected. [...]

1-85 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Ta b l e 1 - 3 1 describes the LEDs for the Cisco 892FSP . T able 1 -31LED desciption for Cisco 892FSP ISR, 896V A, 897V A, and 898EA Routers Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Dat a Routers On the[...]

1-86 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Because the LED indicators are shar ed, the L ED illuminates (green) wh en either port is active. F or example, t he LED indicator labeled BRI 1 B1 illuminat es when either the BRI1 B1 channel is acti ve or when the FXS [...]

1-87 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Note Flash memory is not upgradable. An e xternal USB fl ash memo ry module may be used if additional flash memory is needed. Main Memory Ta b l e 1 - 3 3 describes the main onboard memory storag e for dif ferent router m[...]

1-88 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Fan Some router model s do not ha ve a f an, while other models ha ve either one or tw o fans. The fans spin at full sp eed, as a diagnostic aid, i mmediately after the router is po wered up. After the router has booted [...]

1-89 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs 3G Cellular Data WAN Connectivity The 3G (Evolution Data O nly [EVD O], Universal Mobile T elecomm unication s Systems [ UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a pr[...]

1-90 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Supported Cisco Radio Ante nnas The Cisco 891, Cisco 892, and Ci sco 892F come with three remo v able dipole antennas that can be replaced using the Cisco approved antenna e xtenders listed in Ta b l e 1 - 3 6 . Note Cis[...]

1-91 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Small Form-Factor Pluggable Port The SFP port supports auto-media-detection, auto-failo ver , and remote fault indication (RFI), as described in the IEEE 802.3ah specification. See the Cisco 892F data sheet for a list of [...]

1-92 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs Embedded wireless AP Provides W i-Fi CER TIFIED™ 802.11a/b/g/n compliance. The Cisco 860 series rout ers contain a single 802.11b/g /n radio. Some Cisco 880 series rou ters contain a single 802.11b/g /n radio while oth[...]

1-93 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs USB port, Supports USB 1.1. Provides connectio n for USB de vices such as security tokens and flash memory . The Cisco 880 series routers ha ve a si ngle USB port; the Cisco 890 series routers ha ve tw o USB ports. Cisco [...]

1-94 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 1 Product Ov erview Cisco C891 Series ISRs BRI voice port The ISDN BRI S/T voic e interf ace provides a client-side (TE) ISDN S/T physi cal interface for con nectio n t o an NT1 de vice that terminates an ISDN teleph one network . — 887V — SFP 21 port Support[...]

CH A P T E R 2-1 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 2 Installing the Router This chapter describes the equipment and the pr ocedures for successfully installing the Ci sco 860, 880, 890 ISRs, Cisco 819 ISRs, and t he Cisco 812 ISRs, and cont ains the follo wing section s: • Installing the Cisco 81 0 ISR, page[...]

2-2 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Items Shipped w ith your Router Unpack the bo x and verify tha t all item s listed o n the inv oice were ship ped with the Cis co 812 ISR. The follo wing items are ship ped with your router: • A C power adapt[...]

2-3 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-1 1 0-24 Screws Step 2 Install the PoE+ splitter into the moun ting plate with four 6-32 scre ws. (See Figure 2-2 .) 2 8 5667 1 1 3 2 1 10-24 scre ws 2 Box hanger 3 Shelf bracket (PID 700-39491-01)[...]

2-4 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Figur e 2-2 6-32 Scr ews Step 3 Connect the supplied plenum rated Cat5 cabl e to the GE0 port on the PoE+ spl itter . Step 4 Connect the Cat5 cable from your PoE+ source to the PoE+ in port on the PoE+ splitter[...]

2-5 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 6 Install the power cord with po wer cord lock to the po wer jack of the PoE+ splitter while mak ing sure that the two a rms of th e power cord lock sli de in to the cor res pond ing slo ts on th e PoE + spl[...]

2-6 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Figur e 2-5 T -Rail Installing the SIM Card This section describes how to install and replace the SIM card. Ensure that the router is not mounted to a wall, rack, or DIN rail . Caution Do not touch an y part of[...]

2-7 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-6 A ccessing the SIM Card Step 4 Remove the SIM card and install the ne w cards. Step 5 Reinstall the same 6-32 flat head screws using a sc rew dri ver to secure the access panel back in place. Figure 2[...]

2-8 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Figure 2-7 SIM A ccess P anel Installing the 3G Antenna Note Install the antenna before you mount the Cisco 812 ISR. War ni n g Do not locate the antenna near overhead power lines or other electric light or pow[...]

2-9 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-8 Installi ng the 3G Antenna Step 2 Orient the antenna pe rpendicular with respect to the floor . Figure 2-9 shows the 3G antenna installed. Figur e 2-9 3G Ant enna Installed Mounting the Cisco 812 ISR T[...]

2-10 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR • Mounting Bracket , page 2-10 • Ceiling Grip Clips, p age 2-11 • Mounting the Cisco 812 ISR Belo w a Suspended Ceiling, page 2-13 • Mounting the Cisco 812 ISR on a Hard Ceiling or a W all, page 2-15 ?[...]

2-11 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-1 0 Universal Brac k e t In stalled on the Cisco 812 ISR Ceiling Grip Clips Use a ceiling grid clip to mo unt th e router on a suspended ceiling. Th e ceiling grid clip that you need depends on the ceil[...]

2-12 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Figure 2-11 sh ow s a ceiling grid clip. Figur e 2-1 1 Ceiling Gr id Clip Additional Adapters for Ch annel and Bea m Ceiling Rails The most common type of suspen ded ceiling support rail (the support for the c[...]

2-13 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-12 T -Rail, Channe l, an d Beam Ceiling Rail T ypes Figur e 2-13 Adapter Clips Installed with Ceilin g Gr id Clips Mounting the Cisco 812 ISR Below a Suspended Ceiling The recommended po wer option for [...]

2-14 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Step 7 Hold the mounting bracket and insert a 6-32 x 0.1 8-inch scre w into each of the four correspondi ng holes (A, B, or C) and tighten. Step 8 If necessary , drill or cut a cable access hole in the ceiling[...]

2-15 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-14 Suspended Cei ling Mounting Details Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall This procedure describes th e steps required to mount the Cisco 812 ISR on a cei ling constructed of 3/4-inc[...]

2-16 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Note W all mounting is only supported wi th the I/O (antenna) side f acing up. Step 1 Use the mounting bracket as a template t o mark the locations of the mounti ng holes on the brack et. Figure 2-15 sh ow s d[...]

2-17 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 3 (Opt ional) D rill or cut a cable access hole n ear and below the locatio n of the mo unting br acket cable access cov er lar ge enough for the Et hernet cable, buildi ng ground wire, and po wer cables. S[...]

2-18 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Step 4 Route the cables through the bracket before you attach the bracket t o the ceiling. Step 5 Route the cables through the main ca ble access hole an d then through the smalle r access hole as shown in Fig[...]

2-19 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-1 7 Connecting the Ring Lug ont o the Gr ounding P oint Step 7 Connect the ring lug to the router groun ding point and reinstall the same 6-3 2 screw . Installing the Cisco 819 ISR This section describ[...]

2-20 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR War ni n g This equipment must be grounded. Never de feat the ground conductor or operate the eq uipment in the absence of a suita bly installed ground conductor . Contact the approp riate electrical inspectio[...]

2-21 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Items Shipped with your Router Unpack the bo x and verify tha t all item s listed o n the inv oice were ship ped with the Cis co 819 ISR . The follo wing items are ship ped with your router: • A C power supply[...]

2-22 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR If you plan to conf igure the software using Ci sco IOS commands through the consol e port, prov ide an ASCII terminal or a PC that is run ning terminal emulation softw are to conn ect to the console port. If [...]

2-23 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR War ni n g Do not cover or obstru ct the router vents located on both sides of the rout er; otherwise, overheating could occur and cause d amage to the router . War ni n g Do not place anything on top of the rou[...]

2-24 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Installing Antennas Note Before you install the Cisco 819 ISR on a table, wa ll, or DIN rail, i nstall the antennas on the fron t panel. It is dif f icult to install th e antennas after the router is installed[...]

2-25 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-20 Cisco WiFi Antenna Assembly Installing on a Table T o install the router on a table or other flat hor izontal surf ace, f irmly place the router on a table or other horizontal surface. K eep at le a[...]

2-26 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR T o mount the router on a wall, follow these steps: Step 1 Remove the scre ws on the sides of the routers. Step 2 Attach the standard brackets to the chassis using the three screws provided for each bracket. ([...]

2-27 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-22 Installing the Router t o the W all Note For hollo w-wall mounting, each bracket requires two w all anchors with washers. W all anchors and washers must be size number 10. Step 4 Route the cables so[...]

2-28 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR T o attach the Cisco 819 ISR to a 35-mm wi de DIN rail, follo w these steps. Step 1 Attach the DIN ra il to the back of the ro uter using the three screws provided. (See Figure 2-23 .) Figure 2-23 Attac hing t[...]

2-29 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Figur e 2-25 Cisco 819 ISR Installed with the DIN Rail 282626[...]

2-30 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Installing the Router Using the Co nfigurable Low Profile DIN Mount If space is limited between the DIN rail and th e enclosure co ver , the Conf igurable Low Prof ile DIN Mount can be utilized to moun t the r[...]

2-31 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Configuring the Mount Figur e 2-27 Low Pr ofile DIN Mount Configuration The mount comes conf igured in a bottom cable ex it pos ition, with the rail latches in the slots marked Bottom . T o reconfigure the mount[...]

2-32 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Attaching the mount to the router Figure 2-28 Cisco ISR 81 9 mo unted in a Configurable Low Pr ofile DIN moun t T o attach the router to the mount: 1. Remov e the bottom scre w of the 3 scre ws on the sides of[...]

2-33 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing the Router Ground Connectio n The router must be conn ected to a reliable earth ground . Install the ground wire in accordance with local electrical safety standards. • For NEC-compliant grounding, [...]

2-34 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR After you install and properly ground the rout er , yo u can connect the po wer wiring, the LAN cables, and the cables for administrati ve access as required for your inst allation. Installing the Power Cord R[...]

2-35 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 3 Install the power cord with po wer cord lock and the pre-installed o-ring to mate with the power jack on the router while making sure th at the tw o arms of the po wer cord lock slide into the correspond [...]

2-36 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 810 ISR Figure 2-34 Installing P o wer S w itch Loc k Figur e 2-35 Po w e r S witch Loc k Instal led 344033 1 2 3 4 5 1 Ring terminal 4 Power switch lock 2 Pow er switch lock washer 5 Pan- he ad sc r ew 3 Power swit c[...]

2-37 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 810 ISR Mounting the DC Power Supply War ni n g Read the wall-mounting in structions carefully before beginnin g installation. Failure to use the correct hardware or to follow the correct p rocedures could result in a h[...]

2-38 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Note The DC supply is IP 41 compliant in all six or thogonal directions. The mounting o rientation will not affect IP 41 compliance. Installing the Cisco 860, 880, 890 ISR This section descri bes the[...]

2-39 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Equipment, Tools, and Connections This section descri bes the equipment, tools, and conn ections necessary for instal ling your Cisco 860 series, 880 series, and 890 series ISRs. It contains the fo llo[...]

2-40 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR – T wo number -10 wall an chors with washers, for m ounting the router on a hol low -wall. • W ire crimper for chassis grounding. • W ire for connecting the chassis to an earth ground: – AW G[...]

2-41 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR War ni n g This equipment must be grounde d. Never defeat the ground conductor or ope rate the equipment in the absence of a suita bly installed ground conductor . Contact the appropriate e lectrical i[...]

2-42 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR The mounting holes are bidi rectional. Y ou can hang the r outer with the front bezel f acing upw ard or downw ard. K eep at least 1 inch (2.5 cm) of clear sp ace beside the cooling in let a nd exhau[...]

2-43 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 3 Hang the router on the scre w without forcibly pushing to wards the wall side. The scre w head may damage the protection wa ll inside. Place the po we r adapter on a nearby horizo ntal surf ace.[...]

2-44 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Installing the Router Ground Connection The router must be connected to a reliable earth gro und. Install the ground wire in accordance wi th local electrical safety standards. • For NEC-comp li an[...]

2-45 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 1 Remove th e four mounting scre ws of the top co ver . 284921[...]

2-46 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Step 2 Install the left-side FIPS cov er , as shown in detail A. Step 3 Rotate and bring into the close posit ion to hinge to the correct he xagon. Step 4 Place the adapte r plate before clos ing by [...]

2-47 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 5 Secure the FIPS cov er with two moun ting scre ws. Step 6 Install the right-side FIPS cov er the same way as the left- side FIPS cov er . Step 7 V iew after both cov ers are installed. 284923 28[...]

2-48 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Step 8 If the FIPS cove rs are installed with t he rack mount brackets, the adapter plates are n ot required in the installati on. Installing Antennas for Cisco 890 Series The Cisco 890 series wirele[...]

2-49 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR T o attach the radio antennas to yo ur wireless router , follow these steps: Step 1 Manually screw the an tennas tight to the RP-TNC connecto rs on the back of the rout er . Figure 2-40 Attac h ing An [...]

2-50 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Figure 2-41 Ante nnas Or iented V ertically Up 274774[...]

2-51 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Figure 2-42 Ante nnas Or iented V ertically Down 274775[...]

2-52 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Installing Cisco 890 Series in a Rack The Cisco 890 series ISRs can be mounted i n a rack. T o install a Cisco 890 series ISR in a rack, follo w these steps: Step 1 Remove the scre ws, as shown in Fi[...]

2-53 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Figure 2-44 Attac hing the Rack-mount Br ac k ets to the Cisco 890 Series ISR Caution Chassis installation mu st allo w unrestricted airflo w for chassis cooling. Step 3 Usin g two screws for each side[...]

2-54 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR Step 5 Connect the chassis to a re liable earth ground. Fo r the chassis ground connection pro cedures, see the “Installing Cisco 890 Series i n a Rack” section on page 2-52 . Installing the C881[...]

2-55 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Figure 45 SIM Card Installation 282 3 16 1 2 3 A B 4 A B[...]

2-56 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Chapter 2 In stalling the Router Installing the Cisco 860, 880, 890 ISR T o install the SIM cards, follow these steps: Step 1 Open the door cov ering the SIM card slots. a. Insert the tip of the scre w driver in to the upper latch and gently d isengage it as sho wn in th[...]

CH A P T E R 3-1 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 3 Connecting the Router This chapter describes how to install the Cisc o 860, 880, 890 ISRs and the Cisco 819 ISR. • Cisco 810 Series, page 3-1 • Cisco 860, 880, 890 Series, p age 3-8 Cisco 810 Series Cisco 819 Series This section descri bes ho w to connec[...]

3-2 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Series Preventing D amage to the Route r T o prev ent damage to your router , follow these gu idelines when connecting de v ices to your rout er: • T urn off po wer to the device s and to the router until a ll connections are co[...]

3-3 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Seri es Step 3 (Optional) Connect additional servers, PCs, or w orkstations to t he other Ethernet switch ports. Note Use the Cisco Configurat ion Express to conf igure the Internet connection sett ings. See Cisco Conf iguration Pr[...]

3-4 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Series Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console port either to configure the software by using t he CLI or to troubleshoot problems with t he router . T o connect a terminal or PC to [...]

3-5 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Seri es Connecting a Modem to the Console Port T o connect a modem to the router , follo w these steps: Step 1 Connect the RJ-45 end of the adapter cable to the Console port on the router as sho wn in Figure 3-4 . Figure 3-4 Connec[...]

3-6 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Series T o connect your Cisco 81 9 ISR to an A C power outlet, follow these steps: Step 1 Connect the A C adapter to an A C po wer outlet. Step 2 Plug the adapter cord into the router . Connecting the DC Adapter War ni n g This pr[...]

3-7 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 810 Seri es Figure 3-6 DC P ow er Supply PWR2-20W -12VDC and PWR2-20W -24VDC Step 2 Plug the adapter cord into the router . Note The power ad apters hav e 18 A WG wires for the input connection. T inned bar e wires are used for the inp[...]

3-8 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Cisco 860, 880, 890 Series This section describes how to connect C isco 860 seri es, Cisco 880 series, and Cisco 890 series ISRs to Ethernet devices, Power ov er Ethernet (PoE), and a n etwork. Note Depending on t[...]

3-9 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Note The illustrations i n this chapter sho w a wireless router with antennas attach ed. Non-wireless routers d o not ha ve antennas or ante nna connectors on the ba ck panel. Ho wev er , the procedures for connec[...]

3-10 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series War ni n g Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 War ni n g Never touch uninsulated telephone wires or terminals unless the tele[...]

3-11 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Preventing Damage to the Router T o prev ent damage to your router , follow these gu idelines when connecting de vi ces to your router: • T urn off power to the devices and to the router until all connections a[...]

3-12 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a PC, Server, or Workstation T o connect a PC (or other Et hernet de vices) to an Ethernet switch po rt, follow these steps: Step 1 Connect one end of the yello w Ethernet cable to an Ethernet switch p[...]

3-13 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Connecting a Phone T o connect an 802.3af-compliant ph one to an Ethernet switch port, foll ow these steps: Note A powe r source must be pro vided for the phone to fun ction. This can be done in two ways: the pho[...]

3-14 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 2 Connect the other end of the cable to the RJ-45 port on the phone. Connecting an External Ethernet Switch If more than four PCs in an of f ice must be connecte d to each other , you can ad d Ethernet conne[...]

3-15 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Connecting the V.92 modem Port War ni n g Hazardous network voltages are present in W AN ports regardless of whether power to the unit is OFF or ON. T o avoid electric shock, use caution when working near W AN po[...]

3-16 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Auxiliary (A ux) port either t o conf igure the software by usin g the CLI or to troublesh oot problems with the router . T [...]

3-17 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series When the termi nal emulat or establis hes commu nicatio ns, the rout er prompt is di splayed. For more in formati on on terminal em ulati on settings, see Ap plyin g Corr ect T erminal Emulator Sett ings for Cons[...]

3-18 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting the 3G Card Note For information on embedded multiband, multiservice W AN modems, see Configuring C isco EHWIC and 880G for 3 G (EV -DO Rev A) and Conf iguring Cisco EHWIC and 880G for 3.7G ( HSP A+)/3[...]

3-19 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figure 3-13 Insert ing the 3G Car d Step 2 Open the top of the anti-theft locking brack et, as shown in Figure 3-14 . Figure 3-14 Open ing the Anti-theft Locking Brac k et 1 3G card with the Ci sco logo faci ng u[...]

3-20 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 3 Slide the opened locking brack et under the 3G card. The locking brack et should align with the notches on either side of the 3G card, as sho wn in Figure 3-15 , and the pins on t he lockin g bracket shoul[...]

3-21 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Step 4 Close the locking bracket, as shown in Figure 3-16 . Figur e 3-16 Closing the Locking Br a ck et Step 5 Insert the screws, as sho wn in Figure 3-17 , and tigh ten with a number 2 Philli ps scre wdri ver . [...]

3-22 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Note The antenna c onnector rece ptacle ma y be located on the left, ri ght, or front of t he 3G card , depending on your card. Figure 3-18 an d Figure 3-19 show the antenna connected to the 3G card with an SSMB [...]

3-23 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figur e 3-19 Ant enna with the SMK-TS- 9 Connect or If you are u sing an e xtension c able, you must at tach the 3G a dapter for e xtended cable antenna t o the body of the rout er . Depe nding on t he SKU ord er[...]

3-24 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 8 Remove th e protecti ve tape from the adh esi ve on the bottom of the an tenna cradl e, then f irmly press the cradle to the flat surface. Installing the 3G Adapter for Extended Cable/Antenna For better si[...]

3-25 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Step 2 Locate the hooks on the adapte r as shown in Figure 3-21 . Figur e 3-21 Locating the Hooks on the A dapt er Step 3 Align and insert the hooks of the adapter into the air vent holes on t he left side router[...]

3-26 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 4 Align the circular adapter hole wi th the hol e on the router ch assis from wh ere yo u remo v ed the scre w in Step 1 and use the scre w to attach the adapter to the router as sho wn in Figure 3-23 . Figu[...]

3-27 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Step 5 Connect the extension cable to th e 3G card, as described in the “Connect ing the 3G Card” section o n page 3-18 . The complete assembly is sho wn in Figure 3-24 . Figure 3-24 Adapt er Connected to 3G [...]

3-28 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Note Antenna orientation can increase or decrease signal reception due to polarization . T ypically , an SP’ s transmitting antenn a on the BTS is a v ertically p o larized omnidirection al antenna, which means[...]

3-29 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series T o connect the Data BRI port to the ISDN service pr ovider , follo w these steps: Note Although the follo wing procedure sho ws a Cisco 888W data rout er , this procedure applies to all Cisco 880 series router w[...]

3-30 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 4 Connect the second unshielded Category 5 cable fr om the telecommunication service port on the splitter to the wal l jack to allo w a link to the netw ork service pro vider . Connecting an FE Line to an FE[...]

3-31 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Connecting a GE Line to an GE WAN Port T o connect the Gigabit Ethernet (GE) W AN por t on the router , follow t hese steps: Step 1 Connect one end of the yello w cable to the GE W AN po rt as sho wn in Figure 3-[...]

3-32 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Caution Cisco Systems D SL W AN Interf aces are t ested for compli ance with re gulatory st andards such as FCC Part 6 8, ITU-T K.21, IEC 61000-4- 5, and CSA/EN/IEC/UL 60950-1. These standards assum e Primary Pro[...]

3-33 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figur e 3-28 Pr im ary Pr otection Device Location T o connect the router to a global industry stan dard symmetrical high-speed DSL (G.SHDSL) line, very- high-speed digital subscriber l ine 2 (VDSL2) port, or an [...]

3-34 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Caution The primary W AN po rt is designed fo r an RJ-45 connecto r only . Damage to the primary W AN port may occur if a non-RJ-45 co nnector is inserted. Note The DSL line must be pro v isioned by your service [...]

3-35 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figur e 3-30 Connecting P oE for the Cisco 880 an d th e Cisco 890 Ser ies Routers The Cisco 880 series ISRs with embedded WLAN an tennas r equire a single ex ternal po wer supply: a 30-W power supply for non-POE[...]

3-36 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series T o connect your Cisco 860 series, Cisco 880 series, or the Cisco 890F SP ISR to an A C power outlet, follo w these steps: Step 1 Connect the router to an A C power outlet as sho wn in Figure 3-31 . T o connect t[...]

3-37 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figur e 3-32 Connecting the AC A dapter f or the Cisco 892FSP Figure 3-33 Cisco 892FSP , 896V A, 897V A, and 898EA P ow e r Adapt er Connector Pin Assignment 7 6 GE LAN 5 4 9 GE WAN 8 GE WAN SFP 8 12VDC 2.5A CONS[...]

3-38 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 2 T o secure the power cord to the router , attach the powe r lock clip to the power co rd, sl ide the clip to the end of the DC plug, and secu re the retaining clip i nto the rout er chassis. See Figure 3-3[...]

3-39 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Step 3 Snap the latches into the holes on eith er side of the po wer connec tor . See Figure 3-35 . Figur e 3-35 P ow e r Lo ck Clip La t che d Int o the Holes on Either Side of th e P ower Conn ect o r Connectin[...]

3-40 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series T o conne ct the FXS line, follow these steps: Step 1 Connect one end of the straight-through RJ- 11 cable to the FXS port. Figure 3-36 sho ws an FXS line connection. Figur e 3-36 Connecting an FXS Line Step 2 Co[...]

3-41 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series War ni n g Hazardous network voltages are present in W AN ports regardless of whether power to the unit is OFF or ON. T o avoid electric shock, use caution when working near W AN ports. When detaching cables, det[...]

3-42 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series This option allo ws a stepped offhoo k resistance duri ng seizure, which a voids o verloading the circu it during of fhook in the e vent that ringing v oltage is present on the circuit at the same time as the tru[...]

3-43 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Figure 3-38 sh o ws a v oice BRI line connec tion. Figur e 3-38 Connecting a V o ice BRI Line Step 2 Connect the other end of the cable to the RJ-45 t elephone outlet or othe r de vice. War ni n g Invisible laser[...]

3-44 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series War ni n g Ultimate disposal of this product should be han dled according to al l national laws and regulations. Statement 1040 War ni n g Invisible laser radiation may be emitted from the end of the unterminated[...]

3-45 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series Verifying Connections T o verify that all de vices are prop erly connected to the router , first turn o n all the connected de vices, then check the LEDs. T o verify router operation, refer to Ta b l e 3 - 1 . Fo[...]

3-46 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series T o wireless LAN WLAN LINK W ireless LAN link status: • Green if at least one clie nt is associated. • Off if no client is associated. WLAN 2.4 GHz W ireless LAN 2.4-GH z status: • Green when radio is conne[...]

3-47 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 89 0 Series To W A N G E l i n e (860V AE models only) GE Mode On when GE W AN mode is se lected. Off when the de vice is po wered off or when D SL W AN mode is selected. GE A CT On when the GE W AN interfa ce is up. Blinkin[...]

3-48 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 3 Connecting the Router Cisco 860, 880, 890 Series[...]

CH A P T E R 4-1 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 4 Initial Configuration This chapter pro vides instructions for initial conf iguration of the Cisco 819, 860, 880, 890 Series Integrated Services Routers (ISRs), and contains the follo wing sections: • Cisco 810 Series, page 4-1 • Cisco 860, 880, 890 Serie[...]

4-2 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Verifying the Initial Configuration For more information, r efer to the “V erifying the Initial Con figur ation” section o n page 4-6 . Cisco 860, 880, 890 Series This section pro vides instructions for in iti[...]

4-3 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 89 0 Series Please change these publicly known initial c redentials using Cisco CP Express or the Cisco IOS CLI. Here are the Cisco IOS commands. username <myuser> privilege 15 secret 0 <mypassword> no username us[...]

4-4 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Setup Command Facility The setup command facility guides you through the conf iguration process by prompting you fo r the specific information that is need ed to conf igure your system. Use the setup co mmand faci[...]

4-5 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 89 0 Series Step 5 Enter a hostname for the router (this example uses Router). Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable sec ret password. This password is encrypted (more secure) [...]

4-6 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 890 Series The confi guration is displayed: The following configuration command script was created: hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-serv[...]

4-7 Cisco Integrated Services Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 89 0 Series Initial Configuration of the Wireless Access Point The embedded wireless access point (AP) runs its own I OS. Y ou can initially conf igure the embedded wireless AP by using one of the follo wing methods: • Cisc[...]

4-8 Cisco Integrated Servic es Router Hardware Installation Guide OL-23125-02 Chapter 4 Initial Configuration Cisco 860, 880, 890 Series[...]

A-1 Cisco Integrated Services Router Hardware Installa tion Guide OL-27407-01 APPENDIX A Technical Specifications This appendix pro vides specif ications for the Cisco 860, 880 , 890 Series ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs: • Cisco 810 Series, page A-1 • Cisco 860, 880, 890 Series, p age A-11 Cisco 810 Series This section contains t[...]

A-2 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 810 Series T able A -1 Cisco 812 ISR Specifications Description C812G+7-K9 (3G only) C812G-CIFI+7-E-K9 C812G-CIFI+7-N-K9 C812G-CIFI-V-A-K9 C812G-CIFI-S-A-K9 (3G + WiFi) Physical Characteristics Dimensions (H x W x D) 2.01 x 8.9[...]

A-3 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 810 Seri es Radio Immunity EN301 489-1, EN 301 48 9-7, and EN301 489 -24 T ransportation/Storage Conditions T emperature –40 to158 °F (–40 to 7 0°C) Humidity 5–95 % Altitude 4570 m (15,000 ft ) AC Power Adapter Pow e[...]

A-4 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 810 Series Mean Time Between Failur e Ground Benign Environment Ta b l e A - 2 lists the Mean T ime Between Failure (MTBF) values for Cisco 812 ISRs. The MTBF is calculated based on the Ground Benign condition. Th e v alues may[...]

A-5 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 810 Seri es T able A -3 Cisco 819 IS R Specifications Description Hardened Design Specification (Cisco 819HG and Cisco 819HG-4G ISRs) Non-Hardened Design Specifications (Cisco 819G and Cisco 819G-4G ISRs) Hardened Design Spe[...]

A-6 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 810 Series Standard Safety Certif ications UL 6095 0-1, 2nd edition; CA N/CSA C22.2 No. 60950-1, 2nd edition, EN 60950- 1, 2nd edition; CB to IEC 60950-1, 2nd edit ion with all group d if ferences and national de viations UL 60[...]

A-7 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 810 Seri es Altitude Operating: –500 to 10,000 ft, de-rat ing operating temperature 1°C per 1,000 f eet Non-operating: –1,000 to 30,000 ft Cable Lengt h Input cable: 1 m Output cable: 1.3 m Inrush Current 50 A @ 25°C T[...]

A-8 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 810 Series Mean Time Between Failur e Ground Benign Environment Ta b l e A - 4 lists the Mean T ime Between Failure (MTBF) values for Cisco 819 ISRs. The MTBF is calculated based on the Ground Benign condition. Th e v alues may[...]

A-9 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 810 Seri es Supported Power Adapters Ta b l e A - 5 and Ta b l e A - 6 list the supported po wer adapters for Cisco 819 ISRs. The PWR1 A C and DC adapters uses molex connector while PWR2 uses ba rrel-type connector . C819HGW[...]

A-10 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 810 Series Martek MBRH 0500-D/2 Q21 24 VDC Y es Y es Martek MBRH 0500-D/2 Q21 52 VDC Y es Y es Martek MBRH 0500-D/2 Q21 72 VDC Y es Y es Martek MBRH 0500-D/2 Q21 110 VDC Y es Y es Martek MBRH 0500- B/Q22 24 VDC Y es — Martek[...]

A-11 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Cisco 860, 880, 890 Series This section pro vides router , port, an d cabling speci f ications for the Cisco 860 series, Cisco 880 series, and Cisco 890 seri es ISRs. It cont ains the follo wing topics[...]

A-12 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series • G.SHDSL Port Connec tor Pinouts, pa ge A-25 • Data BRI Port Connecto r Pinouts, page A-26 • V oice ISDN BRI Interf ace Pin Nu mbers and Functions, page A-27 • SFP Port Connector Pinouts, page A-2[...]

A-13 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series T able A -7 Router Specifications Description Design Specification (all models except Cisco 860V AE series) Physical Dimensions Dimensions w ith ante nna and rub ber feet (H x W x D) 1.9 x 12.8 x 10.4 [...]

A-14 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Cisco 860VAE Series Ta b l e A - 8 lists the system specifications fo r the Cisco 860V AE series routers. T able A -8 Router Specifications Description Design Specification Cisco 860V AE series Physical Di[...]

A-15 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E -K9, and Cisco 860VAE-POE-W-A-K9 Series Ta b l e A - 9 lists the system specificati ons for the Cisco 860V AE-W -A-K9, Cisco 860V AE-W -E-K9, and Cisco 860V AE-POE[...]

A-16 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Cisco 870 Series Ta b l e A - 1 2 lists the system specifications for the Cisco 870 series routers. Radio technology IEEE 802.11n draft 2.0 standard compliant. Backward compatibl e with 802.11b/g. Operatin[...]

A-17 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Cisco 880 Series Ta b l e A - 1 2 lists the system specifications for the Cisco 880 series routers. Nonoperating altitude 0 to 15,000 ft (0 to 4 570m) Operating temperature 32 to 104°F (0 to 40°C) Op[...]

A-18 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series T able A -1 1 Rout er Specifications Description Design Specification Physical Dimensions Nonwireless models (H x W x D): • 1.9 x 12.8 x 9.8 in. ( 48 x 325 x 249 mm) (includes rubb er feet) • 1.75 x 12[...]

A-19 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Cisco 880G Series 3G Wirele ss Integrated Services Router Ta b l e A - 1 2 lists the system specifications for the Cisco 880G ser ies 3G W ireless Integrated Services routers. Cisco 880VA Series Ta b l[...]

A-20 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series T able A -13 Rout er Specification s Description Design Specification Physical Dimensions Nonwireless models: • H x W x D = 1.9 x 12.8 x 9. 8 in. (48 x 325 x 249 mm) (includes rub ber feet) • H x W x D[...]

A-21 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Cisco 890 Series Ta b l e A - 1 2 lists the system specifications for the Cisco 890 series routers. T able A -14 Rout er Specification s Description D esign Specification Physical Dimensions Cisco 891,[...]

A-22 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Power Supply Ta b l e A - 1 5 lists the maximum input v alues for the po wer su pply used with the Cisco 860, 880, 890 series ISRs. Wireless Access Point Ta b l e A - 1 6 lists the specifications for the w[...]

A-23 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series FE and GE Port Pinouts Ta b l e A - 1 7 describes the RJ-45 connector pinouts for F ast Ethernet (FE) ports with Po wer o ver Ethernet (PoE). Some models support PoE using an optional module, an d some[...]

A-24 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Console and Auxiliary Port Connector Pinouts T able A-19 lists the pinouts for the console and auxi liary port connectors. FXS and FXO Port Connector Pinouts Ta b l e A - 2 0 lists the FXS and FXO connecto[...]

A-25 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series ADSL2+ Port Connector Pinouts Ta b l e A - 2 2 lists the ADSL2+ connector pinouts. V.92 Port Connector Pinouts Ta b l e A - 2 3 lists the V .92 connect or pinouts. G.SHDSL Port Connector Pinouts Ta b l[...]

A-26 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Ta b l e A - 2 5 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) W AN port for four-pair products, includi ng the follo wing router models: • C888E • C888EW • C888EA Data BRI Port Conn[...]

A-27 Cisco Integr ated Service s Router Ha rdware Insta llat ion Gu ide OL-27407-01 Appendix A T echnical Specifications Cisco 860, 880, 89 0 Series Voice ISDN BRI Interface Pin Numbers and Functions Ta b l e A - 2 7 lists the interface pin numbers and fu nctions fo r the voic e ISDN BRI port. SFP Port Connector Pinouts Ta b l e A - 2 8 lists the p[...]

A-28 Cisco Integrated Servic es Router Hardware Installation Guide OL-27407-01 Appendix A Tec hnica l Specificatio ns Cisco 860, 880, 890 Series Cable Specifications This section provides specifications for the following Ethernet cables: • Straight-throu gh cable • Cr o ss ove r c a b le Because of the autocrossover (autos ensing) fun ction , b[...]