D-Link xStackTM DGS/DXS-3300 Series manuel d'utilisation

©Copyright 2006. All rights reserved. CLI Manual Product Model : xStack TM DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet Switch Release 4.30[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual Table of Contents Introduc tion ................................................................................................................... ................................................ 1 Using the Co nsole CLI ...............................................[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual RIP Comma nds ................................................................................................................... .......................................289 DVMRP Co mmands ................................................................................[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 1 1 I NTRODUCTION The DGS/DXS-3300 Layer 3 stackable Gigabi t Ethernet switches are m embers of the D-Li nk xStack family . Ranging from 10/100Mbps edge switches to core gigabi t switches, the xStack switch fam ily has been future-proof designed t o provide a stacking [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 2 There is no initial username or passwo rd. Just press the Enter key twice to display the CLI input cursor − DGS-3324SRi:4# . This is the comm and line where all com mands are i nput. Setting the Switch’s IP Address Each switch must be assigned its own IP Address,[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 3 Figure 1-3. Assigning an IP Address In the above example, t he Switch was assigned an IP address of 10.53.13.144 with a subnet m ask of 255.0.0.0. The system message Success indicates that the command was execu ted successfully . The Switch can now be configured and [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 4 2 U SING THE C ONSOLE CLI The xStack DGS/DXS-3300 Series supports a console management interface that allows the user to connect to the Switch’s managem ent agent via a serial port and a t erminal or a com puter running a term inal em ulation program. The consol e [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 5 Figure 2-1. Initial Console Screen Comm ands are entered at the com mand prom pts, DGS-3324SRi:4#, DGS-3324SR:4#, DXS-3326GSR:4#, DXS-3350SR:4# . There are a number of helpful features included in the CLI. Entering the ? command will display a list of all of the top [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 6 Figure 2-3. Example Command Parameter Help In this case, the comma nd config account was entered with the parameter <username> . The CLI will then prompt to enter the <username> with th e message, Next possible completions: . Every com mand in the CLI has[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 7 If a comma nd is entered that is unrecognized by the CL I, the top-level comm ands will be displayed under the Available commands: prompt. Figure 2-5. The Available Commands Prompt The top-level com mands consist of comma nds such as show or config . Most of these co[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 8 3 C OMM AND S YNT AX The following sy mbols are used to describe how com mand ent ries are made and values and argum ents are specified in this manual. The online help contained in the CLI and available through the console interface uses the sam e syntax. Note : All [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 9 {braces} Purpose Encloses an optional value or set of optional arguments. Syntax reset {[config | sy stem]} Description In the above syntax example, the user has the option to specify config or sy stem . It is not necessary to specify either optional value, however t[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 10 4 B ASIC S WITCH C OMM ANDS The basic switch comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create account [admin | user] <username 15> config account <username 15&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 11 create account Purpose Used to create user accounts. Syntax create [admin | user] <username 15> Description The create account command is used to create user accounts that consist of a username of 1 to 15 characters and a password of 0 to 15 characters. Up to [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 12 DGS-3324SRi:4#config account dlink Command: config account dlink Enter a old passw ord:**** Enter a case-sensitive new passw ord:**** Enter the new passw ord again for confirmation:**** Success. DGS-3324SRi:4# show account Purpose Used to display user accounts. Synt[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 13 Are you sure to delete the last administrator account?(y /n)y Success. DGS-3324SRi:4# Example usage: To delete the user account “System 2”: DGS-3324SRi:4#delete account System2 Command: delete account System2 Success. DGS-3324SRi:4# show config Purpose Used to d[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 14 DGS-3324SRi:4# show config config_in_NVRAM Command: show config config_in_NVRAM #------------------------------------------------------------------------------------------------------ # DGS-3324SRi Configuration # # Firmw are: Build 4.20-B08 # Copyright(C) 2004- 200[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 15 show switch Purpose Used to display information about the Switch. Syntax show sw itch Description This command displays information about the Switch. Parameters None. Restrictions None. Example usage: To display the Switch information:[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 16 DGS-3324SRi:4#show sw itch Command: show sw itch Device Ty pe : DGS-3324SRi Stackable Ethernet Sw itch Unit ID : 1 MAC Address : DA-10-21-00-00-01 IP Address : 10.41.44.22 (Manual) VLAN Name : default Subnet Mask : 255.0.0.0 Default Gatew ay : 0.0.0.0 Boot PROM Vers[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 17 show switch_mode Purpose Used to display the current switch mode. Syntax show sw itch_mode Description This command displays t he current mode of operation of the Switch. Parameters None. Restrictions None. Example usage: To view the current switch m ode: DGS-3324SR[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 18 show module_info Description This command is used to view information about the DEM-420X and DEM-420CX uplink modules added to an xStack DGS/DXS-3300 series. Currently, only the DXS-3326GSR and the DXS-3350SR members of the xStack DGS/DXS-3300 series have the capabi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 19 show serial_port Parameters None. Restrictions None. Example usage: To display the serial por t setting: DGS-3324SRi:4#show serial_port Command: show serial_port Baud Rate : 115200 Data Bits : 8 P a r i t y B i t s : N o n e Stop Bits : 1 Auto-Logout : 10 mins DGS-3[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 20 DGS-3324SRi:4#config serial_port baud_rate 115200 Command: config serial_port baud_rate 115200 Success. DGS-3324SRi:4# enable clipaging Purpose Used to pause the scrolling of the console screen when the show command displays more than one page. Syntax enable clipagi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 21 Success. DGS-3324SRi:4# enable telnet Purpose Used to enable communication with and management of the Switch using the Telnet protocol. Syntax enable telnet <tcp_port_number 1-65535> Description This command is used to enable the Telnet protocol on the Switch.[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 22 DGS-3324SRi:4#disable telnet Command: disable telnet Success. DGS-3324SRi:4# enable web Purpose Used to enable the HTTP-based management software on the Switch. Syntax enable w eb <tcp_port_number 1-65535> Description This command is used to enable the Web-bas[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 23 To disable HTTP: DGS-3324SRi:4#disable w eb Command: disable w eb Success. DGS-3324SRi:4# save Purpose Used to save changes in the Sw itch’s configuration to non-volatile RAM. Syntax save {[log | all]| Description This command is used to enter the current switch c[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 24 reboot Parameters None. Restrictions None. Example usage: To restart the Switch: DGS-3324SRi:4#reboot Command: reboot Are you sure want to proceed w ith the system reboot? (y /n) Please w ait, the Sw itch is rebooting... reset Purpose Used to reset the Switch to the[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 25 login Description This command is used to initiate the login procedure. The user will be prompted for his Username and Password. Parameters None. Restrictions None. Example usage: To initiate the login p rocedure: DGS-3324SRi:4#login Command: login UserName: logout [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 26 5 S WITCH P OR T C OMM ANDS The switch port commands in the Com mand Line Interface (CLI) ar e listed (along with the appropriate param eters) in the following table. Command Parameters config ports [<portlist> | all] {speed [auto | 10_half | 10_full | 100_hal[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 27 config ports connection must be set for 1000 slave . Any other configuration will result in a link down status for both ports. flow_control [enable | disable] – Enable or disable flow control for the specified ports. learning [enable | disable] − Enables or disa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 28 DGS-3324SRi:4#show ports Command: show ports Port Port Settings Connection Address State Sp eed/Duplex/Flow Ctrl Speed/Duplex/Flow Ctrl Learning ------ -------- --------------------- --------------------- -------- 1:1 Enabled Auto/Enabled Link Dow n Enabled 1:2 Enab[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 29 6 P ORT S ECURITY C OMM ANDS The port security comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config port_security ports [<portlist> | all ] {admin_s tate [enable | di[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 30 To configur e the port security: DGS-3324SRi:4#config port_security ports 5:1-5:5 admin_state enable max_learning_addr 5 lock_address_mode DeleteOnReset Command: config port_security ports 5:1-5:5 admin_state enable max_learning_addr 5 lock_address_mode DeleteOnRese[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 31 delete port_security_entry _vlan_name Purpose Used to delete an entry from the Switch’s port security settings. Syntax delete port_security_entry _vlan_name <v lan_name 32> port <port> mac_address <macaddr> Description This command is used to rem[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 32 7 N ETWORK M ANAGEMENT (SNMP) C OM MANDS The network managem ent comm ands in the Comma nd Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. The xStack DGS/DXS-3300 series supports the Sim ple Network Ma nage ment Protoc[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 33 Command Parameters delete snmp host <ipaddr> show snmp host <ipaddr> create trusted_host <ipaddr> delete trusted_host <ipaddr> show trusted_host <ipaddr> enable snmp traps enable snmp authenticate_traps show snmp traps disable snmp trap[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 34 create snmp user Parameters <username 32> − An alphanumeric name of up to 32 characters that will identify the new SNMP user. <groupname 32> − An alphanumeric name of up to 32 characters that will identify the SNMP group the new SNMP user will be ass[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 35 DGS-3324SRi:4#create snmp user dlink default encrypted by_password auth md5 auth_passw ord priv none Command: create snmp user dlink default encrypted by_password auth md5 auth_passw ord priv none Success. DGS-3324SRi:4# delete snmp user Purpose Used to remove an SN[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 36 DGS-3324SRi:4#show snmp user Command: show snmp user Username Group Name VerAuthPriv --------------- -------------------- --------------------- initial initia l V3 None None Total Entries: 1 DGS-3324SRi:4# create snmp view Purpose Used to assign views to comm unity [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 37 delete snmp view <oid> − The object ID that identifies an object tree (MIB tree) that will be deleted from the Switch. Restrictions Only administrator-lev el users can issue this command. Example usage: To delete a previously configured SNMP view from t h e [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 38 create snmp community Purpose Used to create an SNMP communi ty string to define the relationship between the SNMP manager and an agent. The community string acts like a password to permit access to the agent on the Switch. One or more of the following characteristi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 39 delete snmp community Description The delete snmp community command is used to remove a previously defined SNMP communi ty string from the Switch. Parameters <community_string 32> − An alphanumeric string of up to 32 characters that is used to identify membe[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 40 config snmp engineID Purpose Used to configure a name for the SNMP engine on the Switch. Syntax config snmp engineID <snmp_engineID> Description The config snmp engineID command configures a name for the SNMP engine on the Switch. Parameters <snmp_engineID&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 41 create snmp group Purpose Used to create a new SNMP group, or a table that maps SNMP users to SNMP views. Syntax create snmp group <groupname 32> [v1 | v2c | v 3 [noauth_nopriv | auth_nopriv | auth_priv]] {read_v iew <view _name 32> | w rite_view <vie[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 42 Example usage: To create an SNMP group named “sg1: ” DGS-3324SRi:4#create snmp group sg1 v3 noauth_nopriv read_view v1 w rite_view v1 notify _view v1 Command: create snmp group sg1 v3 noauth_nopriv read_v iew v1 w rite_view v1 notify_view v1 Success. DGS-3324SRi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 43 DGS-3324SRi:4#show snmp groups Command: show snmp groups Vacm Access Table Settings Group Name : Group3 ReadView Name : ReadView WriteView Name : WriteView Notify View Name : NotifyView Security Model : SNMPv 3 Security Lev el : NoAuthNoPriv Group Name : initial Rea[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 44 create snmp host Purpose Used to create a recipient of SNMP traps generated by the Switch’s SNMP agent. Syntax create snmp host <ipaddr> [v1 | v2c | v 3 [noauth_nopriv | auth_nopriv | auth_priv]] <auth_string 32> Description The create snmp host comman[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 45 delete snmp host Purpose Used to remove a recipient of SNMP traps generated by the Switch’s SNMP agent. Syntax delete snmp host <ipaddr> Description The delete snmp host command deletes a recipient of SNMP traps generated by the Switch’s SNMP agent. Parame[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 46 create trusted_host Purpose Used to create the trusted host. Syntax create trusted_host <ipaddr> Description The create trusted_host command creates the trusted host. The Switch allows specification up to four IP addresses that are allowed to manage the Switch[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 47 delete trusted_host Purpose Used to delete a trusted host entry made using the create trusted_host command above. Syntax delete trusted _host <ipaddr> Description This command is used to del ete a trusted host entry made using the create trusted_host command a[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 48 Example Usage: To turn on SNMP authenticati on trap support: DGS-3324SRi:4#enable snmp authenticate_traps Command: enable snmp authenticate_traps Success. DGS-3324SRi:4# show snmp traps Purpose Used to show SNMP trap support on the Switch. Syntax show snmp traps Des[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 49 DGS-3324SRi:4#disable snmp traps Command: disable snmp traps Success. DGS-3324SRi:4# disable snmp authenticate_traps Purpose Used to disable SN MP authentication trap support. Syntax disable snmp authenticate_traps Description This command is used to disable SNMP au[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 50 DGS-3324SRi:4#config snmp syst em_contact MIS Department II Command: config snmp system_contact MIS Department II Success. DGS-3324SRi:4# config snmp system_location Purpose Used to enter a description of the location of the Switch. Syntax config snmp system_locatio[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 51 enable rmon Purpose Used to enable RMON on the Switch. Syntax enable rmon Description This command is used, in conjunction with the disable rmon command below, to enable and disable remote monitoring (RMON) on the Switch. Parameters None. Restrictions Only administr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 52 8 S WITCH U TILITY C OMMANDS The switch utility commands in the Com mand Li ne Interface (CLI) are listed (along with the appropriate parameters) in the following table. Please note that commands concerning the CompactFlash card (cfg_fromC f, firm ware_to CF, etc.) [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 53 download  image_id <int 1-2>- This Switch holds two places for storing firmware so the user may store an extra firmware file on the Switch. image_id 1 will hold the current boot up firmware in use on the Switch, unless otherwise configured.  unit [all | [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 54 To download a PROM code file: DGS-3324SRi:4#dow nload prom_fromTFTP 10.48.74.121 c:pXprom_2.01-B01d1.had DGS-3324SRi:4# dow nload prom_fromTFTP 10.48.74.121 c:pXprom_2.01-B01d1.had Warning! Do not pow er off device before PROM upgrade process has completed! Pow er[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 55 upload Restrictions The TFTP server must be on the same IP subnet as the Switch. Only administrator-level users can issue this command. Example usage: To upload a configuration fil e: DGS-3324SRi:4#upload cfg_toTFTP 10.48.74.121 c:cfglog.txt Command: upload cfg_to[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 56 DGS-3324SRi:4#config firmw are image_id 2 boot_up Command: config firmw are image_id 2 boot_up Success. DGS-3324SRi:4# show firmware information Purpose Used to display the firmware section information. Syntax show firmw are information Description This command is u[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 57 Example usage: To ping the IP address 10.48.74.121 four tim es: DGS-3324SRi:4#ping 10.48.74.121 times 4 Command: ping 10.48.74.121 Reply from 10.48.74.121, time<10ms Reply from 10.48.74.121, time<10ms Reply from 10.48.74.121, time<10ms Reply from 10.48.74.1[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 58 9 N ETWORK M ONIT ORING C OMM ANDS The network monitoring commands in the Comm and Line Interface (C LI) are listed (along with the appropriate parameters) in the following table. Command Parameters show packet ports <portlist> show error ports <portlist>[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 59 show packet ports Purpose Used to display statistics about the packets sent and received by the Switch. Syntax show packet ports <portlist> Description This command is used to di splay statistics about packets sent and received by ports specified in the port l[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 60 show error ports Parameters <portlist> − Specifies a range of ports to be displayed. The port list is specified by listing t he lowest switch number and the beginning port number on that switch, separated by a colon. Then the highest switch number, and the h[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 61 DGS-3324SRi:4#show utilization ports Command: show utilization ports Port TX/sec RX/sec Util Port TX/sec RX/sec Util ---- ---------- ---------- ---- ---- ---------- ---------- ---- 1:1 0 0 0 1:22 0 0 0 1:2 0 0 0 1:23 0 0 0 1:3 0 0 0 1:24 0 0 0 1:4 0 0 0 2:1 0 0 0 1:[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 62 Example usage: To clear the counters: DGS-3324SRi:4#clear counters ports 2:7-2:9 Command: clear counters ports 2:7-2:9 Success. DGS-3324SRi:4# clear log Purpose Used to clear the Switch’s history log. Syntax clear log Description This command will clear the Switch[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 63 DGS-3324SRi:4#show log index 1-4 Command: show log index 1-4 Index Date Time Log Text ----- ---------- -------- ----------------------------------------------------- 4 2000-03-02 01:54:53 Port 1:13 link up, 100Mbps FULL duplex 3 2000-03-02 01:54:53 Spanning Tree Pro[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 64 DGS-3324SRi:4#disable syslog Command: disable syslog Success. DGS-3324SRi:4# show syslog Purpose Used to display the syslog protocol status as enabled or disabled. Syntax show syslog Description The show syslog command displays the syslog status as enabled or disabl[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 65 create syslog host Parameters <index 1-4> − Specifies that the command will be applied to an index of hosts. There are four available indexes, numbered 1 through 4. severity − Severity level indicator, as shown below: Bold font indicates that the correspon[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 66 create syslog host 8 UUCP subsystem 9 clock daemon 10 security/authorization messages 11 FTP daemon 12 NTP subsystem 13 log audit 14 log alert 15 clock daemon 16 local use 0 (local0) 17 local use 1 (local1) 18 local use 2 (local2) 19 local use 3 (local3) 20 local us[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 67 config syslog host Purpose Used to configure the syslog pr otocol to send system log data to a remote host. Syntax config syslog host <index 1-4> [sev erity [informational | w arning | all] | facility [local0 | local1 | local2 | local3 | local4 | local5 | loca[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 68 8 UUCP subsystem 9 clock daemon 10 security/authorization messages 11 FTP daemon 12 NTP subsystem 13 log audit 14 log alert 15 clock daemon 16 local use 0 (local0) 17 local use 1 (local1) 18 local use 2 (local2) 19 local use 3 (local3) 20 local use 4 (local4) 21 loc[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 69 DGS-3324SRi:4# config syslog host 1 udp_port 6000 Command: config syslog host 1 udp_port 6000 Success. DGS-3324SRi:4# config syslog host 1 ipaddress 10.44.67.8 Command: config syslog host 1 ipaddress 10.44.67.8 Success. DGS-3324SRi:4# config syslog host 1 state enab[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 70 config syslog host all facility − Some of the operating system daemons and processes have been assigned Facility values. Processes and daemons that have not been explicitly assigned a Fac ility may use any of the "local use" facilities or they may use th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 71 config syslog host all the remote host, specified above, to be enabled and disabled. Restrictions Only administrator-lev el users can issue this command. Example usage: To configure all syslog hosts : DGS-3324SRi:4#config syslog host all sev erity all Command: confi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 72 DGS-3324SRi:4#delete syslog host 4 Command: delete syslog host 4 Success. DGS-3324SRi:4# show syslog host Purpose Used to display the syslog hosts currently configured on the Switch. Syntax show syslog host {<index 1-4>} Description The show syslog host comman[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 73 config system_severity Purpose To configure when and wher e severity messages are to be recorded. Syntax config system_sev erity [trap | log | all] [critical | w arning | information] Description This command is used to confi gure the system severity levels on the S[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 74 DGS-3324SRi:4#config system_sev erity trap critical Command: config system_sev erity trap critical Success. DGS-3324SRi:4# show system_severity Purpose To display the current severity settings set on the Switch. Syntax show system_sev erity Description This command [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 75 10 M UL TIPLE S P ANNING T REE P ROT OCOL (MSTP) C OMM ANDS This switch supports three versions of the Spanning Tree Pr otocol; 802.1d STP, 802.1w Rapid STP and 802.1s MSTP. Multiple Spanning Tree Protocol, or MSTP, is a sta ndard defined by the IEEE comm unity that[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 76 Command Parameters config stp priority <value 0-61440> instance_id <value 0-15> config stp mst_config_id {revision_level <int 0-65535> | name <string>} config stp mst_ports <portlis t> instance_id <value 0-15> {i nternalCost [auto[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 77 DGS-3324SRi:4#disable stp Command: disable stp Success. DGS-3324SRi:4# config stp version Purpose Used to globally set the version of STP on the Switch. Syntax config stp version [mstp | rstp | stp] Description This command allows the us er to choose the version of [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 78 config stp Parameters maxage <value 6-40> − This value may be set to ensure that old information does not endlessly circulate through redundant paths in the network, preventing the effective propagation of the new information. Set by the Root Bridge, this va[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 79 config stp ports Purpose Used to setup STP on the port level. Syntax config stp ports <portlist> {externalCost [auto | <value 1- 200000000>] | hellotime <value 1-10> | migrate [y es | no] edge [true | false] | p2p [true | false | auto ] | state [en[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 80 config stp ports p2p [true | false | auto] – true indicates a point-to-point (P2P) shared link. P2P ports are similar to edge ports however they are restricted in that a P2P port must operate in full-duplex. Like edge ports, P2P ports transition to a forwarding st[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 81 config stp instance_id Purpose Used to add or delete an STP instance ID. Syntax config stp instance_id <value 1-15> [add_vl an | remove_vlan] <vidlist> Description This command is used to m ap VIDs (VLAN IDs) to previously configured STP instances on the[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 82 delete stp instance_id Purpose Used to delete a STP in stance ID from the Switch. Syntax delete stp instance_id <value 1-15> Description This command allows the user to delete a previously configured STP instance ID from the Switch. Parameters <value 1-15&g[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 83 config stp mst_config_id Purpose Used to update the MSTP configuration identification. Syntax config stp mst_config_id {revision_level <int 0-65535> | name <string> Description This command will uniquely identify the MSTP configuration currently configur[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 84 config stp mst_ports Parameters <portlist> - Specifies a port or range of ports to be configured. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highest switch number,[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 85 Example usage: To display the status of STP on t he Switch: Status 1: STP enabled with STP compatible version DGS-3324SRi:4#show stp Command: show stp STP Status : Enabled STP Version : STP Compatible Max Age : 20 Hello Time : 2 Forw ard Delay : 15 Max Age : 20 TX H[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 86 show stp ports Purpose Used to display the Switch’s current instance_id configuration. Syntax show stp ports <portlist> Description This command displays the STP Instance Settings and STP Instance Operational Status curr ently implemented on the Switch. Para[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 87 DGS-3324SRi:4#show stp instance 0 Command: show stp instance 0 STP Instance Settings --------------------------- Instance Type : CIST Instance Status : Enabled Instance Priority : 32768(bridge priority : 32768, sys ID ext : 0) STP Instance Operational Status -------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 88 11 F ORW ARDING D A T ABASE C OMM ANDS The forwarding database comma nds in the Comma nd Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create fdb <vlan_name 32> <macaddr> port <port&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 89 DGS-3324SRi:4#create fdb default 00-00-00-00-01-02 port 2:5 Command: create fdb default 00-00-00-00-01-02 port 2:5 Success. DGS-3324SRi:4# create multicast_fdb Purpose Used to create a static ent ry to the multicast MAC address forwarding table (database) Syntax cre[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 90 config multicast_fdb Parameters <vlan_name 32> − The name of the VLAN on which the MAC address resides. <macaddr> − The MAC address that will be added to the multicast forwarding table. [add | delete] − Add will add ports to the forwarding table. D[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 91 Example usage: To set the fdb aging time: DGS-3324SRi:4#config fdb aging_time 300 Command: config fdb aging_time 300 Success. DGS-3324SRi:4# delete fdb Purpose Used to delete an entry to the Switch’s forwarding database. Syntax delete fdb <vlan_name 32> <[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 92 clear fdb Purpose Used to clear the Switch’s forwarding database of all dynamically learned MAC addresses. Syntax clear fdb [vlan <vlan_name 32> | port <port> | all] Description This command is used to cl ear dynamically learned entries to the Switch?[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 93 DGS-3324SRi:4#show multicast_fdb Command: show multicast_fdb VLAN Name : default MAC Address : 01-00-5E-00-00-00 Egress Ports : 1:1-1:5,1:26,2:26 Mode : Static Total Entries : 1 DGS-3324SRi:4# show fdb Purpose Used to display the current unicast MAC address forwardi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 94 DGS-3324SRi:4#show fdb Command: show fdb Unicast MAC Address Aging Time = 300 VID VLAN Name MAC Address Port Type ---- ---------------- ----------------- ------ ---------------- 1 default 00-00-39- 34-66-9A 1:12 Dynamic 1 default 00-00-51- 43-70-00 1:12 Dynamic 1 de[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 95 DGS-3324SRi:4#show ipfdb Command: show ipfdb Interface IP Address Port Learned ------------ --------------- ------ ------------ System 10.0.0.1 1:13 Dy namic System 10.0.0.2 1:13 Dy namic System 10.0.0.3 1:13 Dy namic System 10.0.0.4 1:13 Dy namic System 10.0.0.7 1:[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 96 show fdb destination_hit Purpose To view the destination hit status of the Switch. Syntax show fdb destination_hit Description This command will allow users to view the destination hit status of the Switch. Parameters None. Restrictions None. Example usage: To view [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 97 12 B ROADCAST S TOR M C ONTROL C OM MANDS The broadcast storm control comm ands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following tab le. Command Parameters config traffic control [<stor m_grouplist> | all][...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 98 DGS-3324SRi:4#config traffic control all broadcast enable Command: config traffic control all broadcast enable Success. DGS-3324SRi:4# show traffic control Purpose Used to display current traffic control settings. Syntax show traffic control {group_list <storm_gr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 99 13 Q O S C OMM ANDS The xStack DGS/DXS-3300 series support 802.1p priority queuing. These switches has ei ght classes of service for each port on the Switch, one of which i s internal and unconfigurable to th e user. These hardware classes of service are numbered fr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 100 Command Parameters show bandwidth_control {<portlist>} config scheduling <class_id 0-6> {max_packet <value 0-15>} show scheduling config 802.1p user_priority {<pr iority 0-7> <class_id 0-6>} show 802.1p user_priority config 802.1p defa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 101 Example usage: To configure bandwidth control: DGS-3324SRi:4#config bandw idth_control 1:1-1:10 tx_rate 10 Command: config bandw idth_control 1:1-1:10 tx_rate 10 Success. DGS-3324SRi:4# show bandwidth_control Purpose Used to display the bandwidth control configurat[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 102 config scheduling Purpose Used to configure traffic schedu ling for each of the Switch’s hardware priority classes. Syntax config scheduling <class_id 0-6> {max_packet <value 0-15>} Description The Switch contains seven hardw are classes of service pe[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 103 NOTICE: The default QoS scheduling arrangement is a strict priority schedule. To customize scheduling to set up weighted or round-robin class clearing, the max_packets values need to be changed. Example usage: To configure traffic scheduling: DGS-3324SRi:4# config [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 104 DGS-3324SRi:4# show scheduling Command: show scheduling QOS Output Scheduling MAX. Packets ------------------- Class-0 1 Class-1 0 Class-2 3 Class-3 4 Class-4 5 Class-5 6 Class-6 7 DGS-3324SRi:4# config 802.1p user_priority Purpose Used to map the 802.1p user prior[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 105 show 802.1p user_priority Purpose Used to display the current 802.1p us er priority tags to hardware priority class of service mapping in use by the Switch. Syntax show 802.1p user_priority Description The show 802.1p user_priority command will display the current [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 106 Example usage: To configure 802.1p default priority on the Switch: DGS-3324SRi:4#config 802.1p default_priority all 5 Command: config 802.1p default_priority all 5 Success. DGS-3324SRi:4# show 802.1 default_priority Purpose Used to display the currently configured [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 107 1:18 0 1:19 0 1:20 0 1:21 0 1:22 0 1:23 0 1:24 0 DGS-3324SRi:4# config scheduling_mechanism Purpose Used to configure the schedu ling mechanism for the QoS function Syntax config scheduling_mechanism [strict | w eight_fair] Description The config scheduling_mechani[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 108 show scheduling_mechanism Purpose Used to display the current traffic scheduling mechanisms in use on the Switch. Syntax show scheduling_mechanism Description This command will display the current traffic scheduling mechanisms in use on the Switch. Parameters None.[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 109 disable hol_prevention Purpose Used to disable HOL prevention. Syntax disable hol_prevention Description The disable hol_prevention command disables Head of Line prevention. Parameters None. Restrictions Only administrator-lev el users can issue this command. Examp[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 110 14 P ORT M IRRORING C OMM ANDS The port mi rroring comm ands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config mirror port <port> [add | delete] s ource ports <portlist&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 111 To add the mirrori ng ports: DGS-3324SRi:4# config mirror port 1:10 add source ports 1:1-1:5 both Command: config mirror port 1:10 add source ports 1:1-1:5 both Success. DGS-3324SRi:4# config mirror port delete Purpose Used to delete a port mirroring configuration.[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 112 DGS-3324SRi:4#config mirror port 1:10 delete source port 1:1-1:5 both Command: config mirror 1:10 delete source 1:1-1:5 both Success. DGS-3324SRi:4# enable mirror Purpose Used to enable a previously entered port mirroring configuration. Syntax enable mirror Descrip[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 113 show mirror Purpose Used to show the current port mirroring configuration on the Switch. Syntax show mirror Description This command displays the current port mirroring configuration on the Switch. Parameters None. Restrictions None. Example usage: To display m irr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 114 15 VLAN C OMM ANDS The xStack DGS/DXS-3300 series now inco rporates protocol-based VLANs. This standard, defined by the IEEE 802.1v standard maps packets t o protocol-defined VLANs by exam ining th e type octet within the packet head er to discover the type of prot[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 115 create vlan Purpose Used to create a VLAN on the Switch. Syntax create vlan <v lan_name 32> {tag <vlanid 2-4094> | {ty pe {1q_vlan {adv ertisement} | [protocol-ip | protocol-ipx802dot3 | protocol-ipx802dot2 | protocol-ipxSnap | protocol-ipxEthernet2 | p[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 116 create vlan  protocol-ipxEthernet2 - Using this parameter will instruct the Switch to forward packets to this VLAN if the tag in the packet header is concurrent with this protocol. This packet header information is defined by Novell Ethernet II Protocol.  pro[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 117 create vlan  encap [ethernet | llc | snap | all] – Specifies that the Switch will examine the octet of the packet header referring to one of the protocols listed (Ethernet, LLC or SNAP), looking for a match of the hexadecimal value previously entered . all wil[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 118 To remove the VLAN “v1”: DGS-3324SRi:4#delete vlan v 1 Command: delete vlan v1 Success. DGS-3324SRi:4# config vlan add Purpose Used to add additional ports to a previously configured VLAN. Syntax config vlan <v lan_name 32> {[add [ tagged | untagged | for[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 119 config vlan delete Purpose Used to delete ports from a previously configured VLAN. Syntax config vlan <vlan_name 32> delete <portlist> Description This command is used to delete por ts from the port list of a previously configured VLAN. Parameters <v[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 120 config gvrp Parameters <portlist> − A range of ports for which to configure GVRP. The port list is specified by listing the lo west switch number and the beginning port number on that switch, separat ed by a colon. Then the highest switch number, and the hi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 121 DGS-3324SRi:4#enable gvrp Command: enable gvrp Success. DGS-3324SRi:4# disable gvrp Purpose Used to disable GVRP on the Switch. Syntax disable gvrp Description This command, along with enable gvrp below, is used to enable and disable GVRP on the Switch , without ch[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 122 DGS-3324SRi:4#show vlan Command: show vlan VID : 1 VLAN Name : default VLAN TYPE : 1QVLAN Protocol ID : UserDefinedPid : Advertisement : Enabled Encap : Member ports : 1:1-1:24,2:1-2:24 Static ports : 1:1-1:24,2:1-2:24 Untagged ports : 1:1-1:24,2:1-2:24 Forbidden p[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 123 DGS-3324SRi:4#show gvrp Command: show gvrp Global GVRP : Disabled Port PVID GVRP Ingress Checking Acceptable Frame Type ------ ---- -------- ---------------- --------------------------- 1:1 1 Disabled Enabled All Frames 1:2 1 Disabled Enabled All Frames 1:3 1 Disab[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 124 16 L INK A GGREGA TION C OMM ANDS The link aggregation comma nds in the Command Line Interface (CL I) are listed (along with the appropriate parameters) in the following table. Command Parameters create link_aggregation group_id <value 1-32> {type [lacp | sta[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 125 DGS-3324SRi:4#create link_aggregation group_id 1 Command: create link_aggregation group_id 1 Success. DGS-3324SRi:4# delete link_aggregation group_id Purpose Used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id <[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 126 config link_aggregation master_port <port> − Master port ID. Specif ies which port (by port number) of the link aggregation group will be the master port. All of the ports in a link aggregation group will share the port configuration with the master port. T[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 127 config link_aggregation algorithm ip_source − Indicates that the Switch should examine the IP source address. ip_destination − Indicates that the Swit ch should examine the IP destination address. ip_source_dest − Indicates that the Swit ch should examine the[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 128 config lacp_port Purpose Used to configure setti ngs for LACP compliant ports. Syntax config lacp_port <portlist> mode [active | passive] Description This command is used to conf igure ports that have been previously designated as LACP ports (see create link_[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 129 show lacp_port Purpose Used to display current LACP port mode settings. Syntax show lacp_port {<portlist>} Description This command will display the LACP mode settings as they are currently configured. Parameters <portlist> - Specifies a range of ports [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 130 17 IP C OMM ANDS (I NCLUDING IP M UL TINETTING ) IP Multinetting is a function that allows multiple IP interfaces to be assigned to the same VLAN. This is beneficial to the administrator when the number of IPs on the original interface is in sufficient and the netw[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 131 create ipif Purpose Used to create an IP interface on the Switch. Syntax create ipif <ipif_name 12> <netw ork_address> <vlan_name 32> {secondary | {state [enable | disable]} Description This command will create an IP interface. Parameters <ipif[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 132 config ipif Purpose Used to configure an IP interface set on the Switch. Syntax config ipif <ipif_name 12> [{ ipaddress <netw ork_address> | vlan <v lan_name 32> | state [enable | disable]} | bootp | dhcp] Description This command is used to conf [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 133 To enable the ipif fun ction on the Switch: DGS-3324SRi:4#enable ipif s2 Command: enable ipif s2 Success. DGS-3324SRi:4# disable ipif Purpose Used to disable the configurat ion of an IP interface on the Switch. Syntax disable ipif {<ipif_name 12> | all} Descr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 134 DGS-3324SRi:4#delete ipif s2 Command: delete ipif s2 Success. DGS-3324SRi:4# show ipif Purpose Used to display the configurat ion of an IP interface on the Switch. Syntax show ipif {<ipif_name 12>} Description This command will display the configuration of an[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 135 18 IGMP C OMM ANDS (I NCLUDING IGMP V 3) IGMP or Internet Group Management Protoc ol is a protocol implem ented by system s utilizing IPv4 to collect the membership informati on needed by the multicast routi ng protocol through various query messages sent out from [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 136 config igmp Purpose Used to configure IGMP on the Switch. Syntax config igmp [ipif <ipif_name 12> | all] {version <v alue 1-3> | query_interv al <sec 1-31744> | max_response_time <sec 1-25> | robustness_variable <value 1-255> | last_me[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 137 To display IGMP confi gurations: DGS-3324SRi:4#show igmp Command: show igmp IGMP Interface Configurations Interface IP Address/Netmask Ver- Query Maximum Robust- Last State sion Response ness Member Time Value Query Interval ------------ --------------- ---- ------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 138 DGS-3324SRi:4#show igmp group group 224.0.1.1 ipif System Command: show igmp group group 224.0.1.1 ipif System IGMP Group Detail Information Interface : System Multicast Group : 224.0.1.1 Last Reporter : 10.50.77.16 IP Querier : 10.9.68.96 IP Expire : 217 Filter Mo[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 139 19 IGMP S NOOPING C OM MANDS The IGMP Snooping comma nds in the Comma nd Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config igmp_snooping [<vlan_name 32> | a ll] {host_timeout <sec 1-16[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 140 config igmp_snooping host_timeout <sec 1-16711450> − Specifies the maximum amount of time a host can be a member of a multicas t group without the Switch receiving a host membership report. The default is 260 seconds. router_timeout <sec 1-16711450> ?[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 141 config igmp_snooping querier between general query transmissions. The default setting is 125 seconds. max_response_time <sec 1-25> − Specifies the maximum time in seconds to wait for reports from members. The default setting is 10 seconds. robustness_variab[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 142 enable igmp_snooping Purpose Used to enable IGMP snooping on the Switch. Syntax enable igmp_snooping {forward_mcrouter_only} Description This command allows the user to enable IGMP snooping on the Switch. If forw ard_mcrouter_only is specified, the Swit ch will onl[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 143 config router_ports Purpose Used to configure ports as router ports. Syntax config router_ports <vlan_name 32> [add | delete] <portlist> Description This command allows desi gnation of a range of ports as being connected to multicast-enabled router s. T[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 144 config router_ports_forbidden Parameters <vlan_name 32> − The name of the VLAN on which the router port resides. [add | delete] - Specifies whether to add or delete forbidden ports of the specified VLAN. <portlist> − Specifies a range of ports that [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 145 DGS-3324SRi:4#show router_ports Command: show router_ports VLAN Name : default Static router port : 2:1-2:10 Dynamic router port : Forbidden Router Port: VLAN Name : vlan2 Static router port : Dynamic router port : Forbidden Router Port: Total Entries: 2 DGS-3324SR[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 146 DGS-3324SRi:4#show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State : Disabled Multicast router Only : Disabled VLAN Name : default Query Interv al : 125 Max Response Time : 10 Robustness Value : 2 Last Member Query Interv al : 1 Host Timeout : [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 147 DGS-3324SRi:4#show igmp_snooping group Command: show igmp_snooping group VLAN Name : default Multicast group: 224.0.0.2 MAC address : 01-00-5E-00-00-02 Reports : 1 Port Member : 1:26,2:7 VLAN Name : default Multicast group: 224.0.0.9 MAC address : 01-00-5E-00-00-09[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 148 To view the IGMP snooping forwarding t able for VLAN “Trinity”: DGS-3324SRi:4#show igmp_snooping forw arding vlan Trinity Command: show igmp_snooping forw arding vlan Trinity VLAN Name : Trinity Multicast group : 224.0.0.2 MAC address : 01-00-5E-00-00-02 Port M[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 149 20 MAC N OTIFICA TION C OMM ANDS The MAC notification commands in the Co mm and Line Interface (CLI) are listed, in the following table, along with their appropriate param eters. Command Parameters enable mac_notification disable mac_notification config mac_notific[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 150 Example Usage: To disable MAC noti fication without changi ng basic configuration: DGS-3324SRi:4#disable mac_notification Command: disable mac_notification Success. DGS-3324SRi:4# config mac_notification Purpose Used to configure MAC address notification. Syntax co[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 151 config mac_notification ports [enable | disable] – These commands will enable or disable MAC address table notification on the Switch. Restrictions Only administrator-lev el users can issue this command. Example usage: To enable port 7 for MAC address ta ble noti[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 152 show mac_notification ports Purpose Used to display the Switch’s MAC address table not ification status settings. Syntax show mac_notification ports <portlist> Description This command is used to display the Switch’s MAC address table notification status [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 153 21 A CCESS A UTHENTICA TION C ONTROL C OMM ANDS The Access Authentication Control comma nds allows secure access to the Switch us ing the TACACS / XTACACS / TACACS+ and RADIUS protocols. When a user logs in to the Switch or tries to access the administrator level p[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 154 The Access Authentication Control comma nds in the Command Line Interface (CLI) ar e listed (along with the appropriate parameters) in the following table. Command Parameters enable authen_policy disable authen_policy show authen_policy create authen_login method_l[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 155 Command Parameters enable admin config admin local_enable <password 15> Each command is listed, in detail, in the followin g sections. enable authen_policy Purpose Used to enable system access authentication policy. Syntax enable authen_policy Description Thi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 156 show authen_policy Purpose Used to display the system access authentication policy status on the Switch. Syntax show authen_policy Description This command will show t he current status of the access authentication policy on the Switch. Parameters None. Restriction[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 157 config authen_login Purpose Used to configure a user-defined or default method list of authentication methods for user login. Syntax config authen_login [default | method_list_name <string 15>] method {tacacs | xtacacs | tacacs+ | radius | server_group <st[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 158 config authen_login method_list_name – Enter a previously implemented method list name defined by the user. The user may add one, or a combination of up to four (4) of the following authenticat ion methods to this method list:  tacacs – Adding this parameter[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 159 delete authen_login method_list_name Purpose Used to delete a previously configured user defined method list of authentication methods for users logging on to the Switch. Syntax delete authen_login method_list_name <string 15> Description This command is used[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 160 show authen_login Parameters default – Entering this parameter will display the default method list for users logging on to the Switch. method_list_name <string 15> – Enter an alphanumeric string of up to 15 characters to define the given method list to v[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 161 config authen_enable Purpose Used to configure a user- defined method list of authentication methods for promoting normal user level privileges to Administrator level privileges on the Switch. Syntax config authen_enable [default | method_list_name <string 15>[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 162 config authen_enable method_list_name – Enter a previously implemented method list name defined by the user ( create authen_enable ). The user may add one, or a combination of up to four (4) of the following authentication methods to this method list:  tacacs [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 163 delete authen_enable method_list_name Purpose Used to delete a user-defined method list of authentication methods for promoting normal user level pr ivileges to Administrator level privileges on the Switch. Syntax delete authen_enable method_list_name <string 15[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 164 show authen_enable Parameters default – Entering this parameter will display the default method list for users attempting to gain access to Administrator level privileges on the Switch. method_list_name <string 15> – Enter an alphanumeric string of up to [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 165 config authen application login – Use this parameter to configure an application for normal login on the user level, using a pr eviously configured method list. enable - Use this parameter to configure an application for upgrading a normal user level to administr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 166 create authen server_host Purpose Used to create an authentication server host. Syntax create authen server_host <ipaddr> protocol [tacacs | xtacacs | tacacs+ | radius] {port <int 1-65535> | key [<key _string 254> | none] | timeout <int 1-255&g[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 167 DGS-3324SRi:4#create authen server_host 10.1.1.121 protocol tacacs+ port 1234 timeout 10 retransmit 5 Command: create authen server_host 10.1.1.121 protocol tacacs+ port 1234 timeout 10 retransmit 5 Success. DGS-3324SRi:4# config authen server_host Purpose Used to [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 168 config authen server_host timeout <int 1-255> - Enter the time in seconds the Switch will wait for the server host to reply to an authentication request. The default value is 5 seconds. retransmit <int 1-255> - Enter the value in the retransmit field to[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 169 DGS-3324SRi:4#delete authen server_host 10.1.1.121 protocol tacacs+ Command: delete authen server_host 10.1.1.121 protocol tacacs+ Success. DGS-3324SRi:4# show authen server_host Purpose Used to view a user- defined authentication server host. Syntax show authen se[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 170 create authen server_group Purpose Used to create a user-def ined authentication server group. Syntax create authen server_group <string 15> Description This command will create an aut hentication server group. A server group is a technique used to gr oup TAC[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 171 config authen server_group  tacacs – Use this parameter to utilize the built-in TACACS server protocol on the Switch . Only server hosts utilizing the TACACS protocol may be added to this group.  xtacacs – Use this parameter to utilize the built-in XTACAC[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 172 Example usage: To delete the server group “group_1”: DGS-3324SRi:4#delete server_group group_1 Command: delete server_group group_1 Success. DGS-3324SRi:4# show authen server_group Purpose Used to view authenticati on server groups on the Switch. Syntax show au[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 173 config authen parameter response_timeout Parameters response_timeout <int 0-255> - Set the time, in seconds, the Switch will wait for a response of authenticat ion from the user attempting to log in from the command line interface or telnet interface. An entr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 174 To set the maximum number of authentication attempts at 5: DGS-3324SRi:4#config authen parameter attempt 5 Command: config authen parameter attempt 5 Success. DGS-3324SRi:4# show authen parameter Purpose Used to display the authenticat ion parameters currently conf[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 175 enable admin Parameters None. Restrictions Only administrator-lev el users can issue this command. Example usage: To enable administrator privileges o n the Switch: DGS-3324SRi:4#enable admin Passw ord: ****** DGS-3324SRi:4# config admin local_enable Purpose Used t[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 176 22 SSH C OMM ANDS The steps required to use the SSH protocol for secure com munica tion between a remote PC (the SSH Client ) and the Switch (the SSH Server), are as follows:  Create a user account with admin-level access using the create account admin <usern[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 177 enable shh Purpose Used to enable SSH. Syntax enable ssh Description This command will enable SSH on the Switch. Parameters None. Restrictions Only administrator-lev el users can issue this command. Usage Example: To enable SSH: DGS-3324SRi:4#enable ssh Command: en[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 178 config ssh authmode Parameters password – This parameter may be c hosen if the administrator wishes to use a locally configured password for authentication on the Switch. publickey - This parameter may be chosen if the administrator wishes to use a publickey conf[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 179 config ssh server Purpose Used to configure the SSH server. Syntax config ssh server {maxsession <int 1-3> | contimeout <sec 120- 600> | authfail <int 2-20> | rekey [10min | 30min | 60min | nev er]} Description This command will configure the SSH [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 180 DGS-3324SRi:4# show ssh server Command: show ssh server SSH Server Status : Disabled SSH Max Session : 3 Connection timeout : 120 (sec) Authenticate failed attempts : 2 Rekey timeout : Nev er Listened Port Number : 22 DGS-3324SRi:4# config ssh user Purpose Used to [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 181 show ssh user authmode Purpose Used to display the SSH user setting. Syntax show ssh user authmode Description This command will displa y the current SSH user setting. Parameters None. Restrictions None. Example usage: To display the SSH user: DGS-3324SRi:4#show ss[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 182 config ssh algorithm twofish128 - This parameter will enable or disable the twofish128 encryption algorithm. twofish192 - This parameter will enable or disable the twofish192 encryption algorithm. MD5 - This parameter will enable or disable the MD5 Message Digest e[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 183 DGS-3324SRi:4#show ssh algorithm Command: show ssh algorithm Encryption Algorithm -------------------------------------- 3DES :Enabled AES128 :Enabled AES192 :Enabled AES256 :Enabled ARC4 :Enabled Blow fish :Enabled Cast128 :Enabled Tw ofish128 :Enabled Tw ofish192[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 184 23 SSL C OMM ANDS Secure Sockets Layer or SSL is a security feature that will prov ide a secure communication path between a host and client through the use of authentication, digital si gnatures and encryption. These security functions are im plemented t hrough th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 185 enable ssl Purpose To enable the SSL function on the Switch. Syntax enable ssl {ciphersuite {RSA_w ith_RC4_128_MD5 | RSA_w ith_3DES_EDE_CBC_SHA | DHE_DSS_w ith_3DES_EDE_CBC_SHA | RSA_EXPORT_w ith_RC4_40_MD5}} Description This command will enable SSL on the Switch b[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 186 NOTE: Enabling the SSL function on the Sw itch will disable the port for the web manager (port 80). To log on to the web based manager, the entry of your URL must begin with https:// . (ex. https://10.90.90.90) disable ssl Purpose To disable the SSL function on the[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 187 config ssl cachetimeout Purpose Used to configure the SSL cache timeout. Syntax config ssl cachetimeout <value 60-86400> Description This command will set the time between a new key exchange between a client and a host using the SSL function. A new SSL sessio[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 188 show ssl Purpose Used to view the SSL status and the certificate file status on the Switch. Syntax show ssl {certificate} Description This command is used to view the SSL status on the Switch. Adding the certificate parameter will allow the user to view the certifi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 189 download certificate_fromTFTP certfilename <path_filename 64> - Enter the path and the filename of the certificate file to download. keyfilename <path_filename 64> - Enter the path and the filename of the key exchange file to download. Restrictions Only[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 190 24 802.1X C OMM ANDS The xStack DGS/DXS-3300 series implem ent the server-side of the IEEE 802.1x Port-based and MAC-based Network Access Control. This mechanism is intended to a llow only authorized users, or other netw ork devices, access to network resources by [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 191 Each command is listed, in detail, in the followin g sections. enable 802.1x Purpose Used to enable the 802.1x server on the Switch. Syntax enable 802.1x Description The enable 802.1x command enables the 802.1x Network Access control server applicati on on the Swit[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 192 create 802.1x user Purpose Used to create a new 802.1x user. Syntax create 802.1x user <username 15> Description The create 802.1x user command is used to create new 802.1x users. Parameters <username 15> − A username of up to 15 alphanumeric characte[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 193 delete 802.1x user Purpose Used to delete an 802.1x user account on the Switch. Syntax delete 802.1x user <username 15> Description The delete 802.1x user command is used to delete the 802.1x Port- based or MAC-based Network Access control local users current[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 194 show 802.1x auth_configuration Port Control: ForceAuth/ForceUnauth/Auto − Shows the administrative control over the port’s authorization status. ForceAuth forces the Authenticator of the port to become Authorized. ForceUnauth forces the port to become Unauthori[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 195 show 802.1x auth_state Purpose Used to display the current authent ication state of t he 802.1x server on the Switch. Syntax show 802.1x auth_state {ports [<portlist> | all]} Description The show 802.1x auth_state command is used to display the current authen[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 196 DGS-3324SRi:4#show 802.1x auth_state Command: show 802.1x auth_state Port Auth PAE State Backend State Port Status ------ ----------------------- --------------------- ----------------- 1:1 ForceAuth Success Authorized 1:2 ForceAuth Success Authorized 1:3 ForceAuth[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 197 config 802.1x auth_mode Purpose Used to configure the 802.1x authentication mode on the Switch. Syntax config 802.1x auth_mode {port_based | mac_based] Description The config 802.1x authentication mode command is used to enable either the port-based or MAC-based 80[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 198 DGS-3324SRi:4#config 802.1x capability ports 1:1 – 1:10 authenticator Command: config 802.1x capability ports 1:1 – 1:10 authenticator Success. DGS-3324SRi:4# config 802.1x auth_parameter Purpose Used to configure the 802. 1x Authentication parameters on a rang[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 199 config 802.1x auth_parameter tx_period <sec 1-65535> - Configures the time to wait for a response from a supplicant (u ser) to send EAP Request/Identity packets. supp_timeout <sec 1-65535> - Configures the time to wait for a response from a supplicant ([...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 200 DGS-3324SRi:4# config 802.1x auth_protocol local Command: config 802.1x auth_protocol local Success. DGS-3324SRi:4# config 802.1x init Purpose Used to initialize the 802. 1x function on a range of ports. Syntax config 802.1x init [port_based ports [<portlist>[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 201 DGS-3324SRi:4# config 802.1x init port_based ports all Command: config 802.1x init port_based ports all Success. DGS-3324SRi:4# config 802.1x reauth ports Purpose Used to configure the 802.1x re-authentication feature of the Switch. Syntax config 802.1x reauth [por[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 202 To configure 802.1x reauthenticati on for ports 1-18 on switch 1: DGS-3324SRi:4#config 802.1x reauth port_based ports 1:1-1:18 Command: config 802.1x reauth port_based ports 1:1-1:18 Success. DGS-3324SRi:4# config radius add Purpose Used to add a new RADIUS server.[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 203 config radius delete Purpose Used to delete a previously entered RADIUS server configuration. Syntax config radius delete <server_index 1-3> Description The config radius delete command is used to delete a previously entered RADIUS server configuration. Param[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 204 DGS-3324SRi:4# config radius 1 ipaddress 10.48.74.121 key dlink Command: config radius 1 ipaddress 10.48.74.121 key dlink Success. DGS-3324SRi:4# show radius Purpose Used to display the current RA DIUS configurations on the Switch. Syntax show radius Description Th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 205 DGS-3324SRi:4#show acct_client Command: show acct_client radiusAcctClient --------------------------------------------------------------------------------------- radiusAcctClientInvalidServerAddresses 0 radiusAcctClientIdentifier D-Link radiusAuthServerEntry 0 ----[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 206 DGS-3324SRi:4#show auth_client Command: show auth_client radiusAuthClient ---------------------------------------------------------------------------------------- radiusAuthClientInvalidServerAddresses 0 radiusAuthClientIdentifier D-Link radiusAuthServerEntry 0 ---[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 207 DGS-3324SRi:4#show auth_diagnostics ports 1:16 Command: show auth_diagnostics ports 1:16 Port number : 1:16 EntersConnecting 0 EapLogoffsWhileConnecting 0 EntersAuthenticating 0 SuccessWhileAuthenticating 0 TimeoutsWhileAuthenticating 0 FailWhileAuthenticating 0 Re[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 208 DGS-3324SRi:4#show auth_session_statistics ports 1:16 Command: show auth_session_statistics ports 1:16 Port number : 1:16 SessionOctetsRx 0 SessionOctetsTx 0 SessionFramesRx 0 SessionFramesTx 0 SessionId SessionAuthenticMethod Remote Authentication Server SessionTi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 209 DGS-3324SRi:4#show auth_statistics ports 1:16 Command: show auth_statistics ports 1:16 Port number : 1:16 EapolFramesRx 0 EapolFramesTx 0 EapolStartFramesRx 0 EapolReqIdFramesTx 0 EapolLogoffFramesRx 0 EapolReqFramesTx 0 EapolRespIdFramesRx 0 EapolRespFramesRx 0 In[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 210 25 A CCESS C ONTROL L IST (ACL) C OMM ANDS The xStack DGS/DXS-3300 series implement Access Control Lists that enable the Sw itch to deny network access to specific devices or device groups based on IP settings, MAC address, packet content, IPv6 settings or CPU. Com[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 211 Command Parameters 0xffffffff> <hex 0x0-0xffffffff> | {offset 64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>}] |ipv6 {class | flowlabel | source ipv6mask <ipv6mask> | destination_ipv6[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 212 access_id gives the rule a higher priority. In case of a conflict in the rules entered for an access profile, the rule with the highest priority (lowest access_id ) will take precedence. The ip parameter instructs the Switch that this new rule will be applied to th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 213 Command Parameters create access_profile [ethernet {vl an | source_mac <macmask 000000000000- ffffffffffff> | destination_mac <mac mask 000000000000- ffffffffffff> | 802.1p | ethernet_type} profile_id <value 1-8>} config access_profile profile_id [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 214 create access_profile (for Ethernet) Purpose Used to create an access profile on the Switch by examining the Ethernet part of the packet header. Masks entered can be combined with the values the Switch finds in the specified frame header fields. Specific values for[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 215 config access_profile profile_id (for Ethernet) Syntax config access_profile profile_id <value 1-8> [add access_id [auto assign | <value 1-65535>] [ethernet {vlan <v lan_name 32> | source_mac <macaddr 000000000000-ffffffffffff> | destination[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 216 config access_profile profile_id (for Ethernet) permit – Specifies that packets that match the access profile are permitted to be forwarded by the Switch. • priority <value 0-7> − This parameter is specified to re-write the 802.1p default priority previ[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 217 create access_profile (IP) Purpose Used to create an access profile on the Switch by examining the IP part of the packet header. Masks entered can be combined with the values the Switch finds in the s pecified frame header fields. Specific values for the rules are [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 218 create access_profile (IP) • flag_mask [all | {urg | ack | psh | rst | syn | fin}] – Enter the appropriate flag_mask parameter. All incoming packets have TCP port numbers contained in them as the forwarding criterion. These numbers have fl ag bits associated wi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 219 config access_profile profile_id (IP) Description This command is used to define the ru les used by the Switch to either filter or forward packets based on t he IP part of each packet header. Parameters profile_id <value 1-8> - Enter an integer between 1 and [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 220 config access_profile profile_id (IP) • flag_mask – Enter the type of TCP flag to be masked. The choices are: • urg : TCP control flag (urgent) • ack : TCP control flag (acknowledgement) • psh : TCP control flag (push) • rst : TCP control flag (reset) ?[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 221 config access_profile profile_id (IP) mirror - Selecting mi rror specifies that packets that match the access profile are mirrored to a port defined in the config mirror port command. Port Mirroring must be enabled and a target port must be set. Remember, Port Mirr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 222 create access_profile (packet content mask) Description This command is used to ident ify packets by examining the Ethernet packet header, by byte and then decide w hether to filter or forward it, based on the user’s configuration. The user will specify which byt[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 223 config access_profile profile_id (packet content mask) 0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex0x0-0xffffffff>} port <port> [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 224 config access_profile profile_id (packet content mask) permit – Specifies that packets that match the access profile are permitted to be forwarded by the Switch. • priority <value 0-7> − This parameter is specified to re-write the 802.1p default priorit[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 225 create access_profile (ipv6) Purpose Used to create an access profile on the Switch by examining the IPv6 part of the packet header. Masks can be entered that will be combined with the values the Switch finds in the specified frame header fields. Specific values fo[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 226 config access_profile profile_id (ipv6) Syntax config access_profile profile_id <value 1-8> add access_id {auto_assign | <value 1-165535>] ipv6 {class <v alue 0-255> | flow label <hex 0x0-0xfffff> | source_ipv6 <ipv6addr> | destionatio[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 227 config access_profile profile_id (ipv6) • priority <value 0-7> − This parameter is specified to re-write the 802.1p default priority previously set in the Switch, which is used to determine the CoS queue to which packets are forwarded to. Once this field [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 228 delete access_profile Parameters profile_id <value 1-8> − Enter an integer between 1 and 8 that is used to identify the access profile that will be deleted with this command. This value is assigned to the access profile when it is created with the create ac[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 229 ====================================================================== Access Profile ID: 2 TYPE : IP ====================================================================== MASK Option : Protocol ID -------------------- Access ID : 2 Mode: Deny Ports: 1:2 ---------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 230 create cpu access_profile Syntax create cpu access_profile [ethernet {vlan | source_mac <macaddr 000000000000-ffffffffffff>| destinati on_mac <macaddr 000000000000- ffffffffffff> | 802.1p | ethernet_type} | ip {v lan | source_ip_mask <netmask> | d[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 231 create cpu access_profile • igmp − Specifies that the Switch w ill examine each frame’s Internet Group Management Protocol (IGMP) field. • type − Specifies that the Switch will examine each frame’s IGMP Type field. • tcp − Specifies that the Switch [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 232 create cpu access_profile • class – Entering this parameter will instruct the Switch to examine the class field of the IPv6 header. This class field is a part of the packet header that is similar to the Type of Service (ToS) or Precedence bits field in IPv4. ?[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 233 config cpu access_profile Purpose Used to configure a CPU access prof ile used for CPU Interface Filtering and to define specific values that will be used to by the Switch to determine if a given packet should be forwarded or filtered. Masks entered using the creat[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 234 config cpu access_profile • ethernet_type <hex 0x0-0x ffff> − Specifies that the access profile will apply only to packets with this hexadecimal 802.1Q Ethernet type value in the packet header. ip − Specifies that the Switch will look into the IP fields[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 235 config cpu access_profile • packet_content_mask – Specifies that the Switch will mask the packet header beginning with the offset value specified as follows: • offset_0-15 - Enter a value in hex form to mask the packet from byte 0 to byte 15. • offset_16-31[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 236 enable cpu_interface_filtering Purpose Used to enable CPU interface filtering on the Switch. Syntax enable cpu_interface_filtering Description This command is used, in conjunction with the disable cpu_interface_filtering command below, to enable and disable CPU int[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 237 To show the CPU filtering state o n the Switch: DGS-3324SRi:4#show cpu access_profile Command: show cpu access_profile CPU Interface Filtering state: Disabled CPU Interface Filtering Access Profile Table Access Profile ID: 1 TYPE: Ethernet Mask Option: VLAN -------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 238 26 T RAFFIC S EGMENT A TION C OMM ANDS Traffic segmentation allows furt her sub-division of VLANs into sm aller groups of ports that w ill help to reduce traffic on the VLAN. The VLAN rules take precedence, a nd then the traffic segmentation rules are applied. The [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 239 show traffic_segmentation Purpose Used to display the current tr affic segmentation configuration on the Switch. Syntax show traffic_segmentation <portlist> Description The show traffic_segmentation command is used to display the current traffic segmentation [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 240 27 S T ACKING C OMMANDS The stacking configuration comma nds in th e Comm and Line Interface (CLI) are listed (a long with the appropriate parameters) in the following tab le. Command Parameters config box_priority current_box_id <value 1-12> priority <val[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 241 config box_id Purpose Used to configure box ID. Us ers can use this command to reassign box IDs. Syntax config box_id {current_box_id <value 1-12> new_box_id [AUTO | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12]} Description This command will assign box I[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 242 Usage Example: To configure box type: DGS-3324SRi:4#config box_type current_box_id 3 ty pe BOX_NOTEXIST Command: config box_type current_box_id 3 ty pe BOX_NOTEXIST Success. DGS-3324SRi:4# config all_boxes_id Purpose Used to configure box IDs for switches in a stac[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 243 DGS-3324SRi:4#show stack_information Command: show stack_information Box User Prio- Prom Runtime H/W ID Set Type Exist rity version version version --- ---- ----------- ----- ----- -------- -------- -------- 1 AUTO DGS-3324SRi exi st 16 2.01-B01 4.30-B08 2A1 2 - US[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 244 28 D-L INK S INGLE IP M ANAGEM ENT C OMMANDS Simply put, D-Link Single IP Management is a con cept that will stack switches together over Ethernet in stead of usin g stacking ports or m odules. Switches using Single IP M anagement (labeled here as SIM) must conform[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 245 b. If report packets from the CS to the MS time out. 5. The user can manually configure a CaS to becom e a CS 6. The CaS can be configured through the CS t o become a MS. After configuring one switch to operate as the CS of a SIM group, additional switches may join[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 246 Command Parameters config sim [{[commander {group_nam e <groupname 64> | candidate] | dp_interval <sec 30-90> | hold_time <sec 100-255>} download sim_ms [firmware_from_tftp | configuration_from_tftp] <ipaddr> <path_filename> {[members [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 247 show sim Purpose Used to view the current information regarding the SIM group on the Switch. Syntax show sim {[candidates {<candidate_id 1-100>} | members {<member_id 1-32>} | group {commander_mac <macaddr>} neighbor]} Description This command wil[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 248 DGS-3324SRi:4#show sim Command: show sim Group Name : default SIM Version : VER-1.61 Firmw are Version : Build 4.30-B08 Device Name : MAC Address : 00-35-26-11-11-00 Capabilities : L3 Platform : DGS-3324SRi L3 Sw itch SIM State : Enabled Role State : Commander Disc[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 249 ID MAC Address Platform / Hold Firmw a re Device Name Capability Time Version --- ----------------- ------------------------ ----- --------- ---------------- 2 00-55-55-00-55-00 DXS-3350 L3 Sw itch 140 4.30-B08 Enrico SIM Group Name : SIM2 ID MAC Address Platform /[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 250 DGS-3324SRi:4#reconfig member_id 2 Command: reconfig member_id 2 DGS-3324SRi:4# config sim_group Purpose Used to add candidates and delete members from the SIM group. Syntax config sim_group [add <candidate_id 1-100> {<passw ord>} | delete <member_id[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 251 config sim Purpose Used to configure role param eters for the SIM protocol on the Switch. Syntax config sim [{[commander {group_name <groupname 64> | candidate] | dp_interval <30-90> | hold_time <sec 100-255>}] Description This command is used to [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 252 DGS-3324SRi:4#config sim candidate Command: config sim candidate Success. DGS-3324SRi:4# To transfer the Switch to be a comma nder: DGS-3324SRi:4#config sim commander Command: config sim commander Success. DGS-3324SRi:4# To update the name of a group: DGS-3324SRi:4[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 253 Example usage: To download firmware: DGS-3324SRi:4# dow nload sim_ms firm w are 10.53.13.94 c:/dgssri.had all Command: dow nload sim_ms firmw are 10.53.13.94 c:/dgssri.had all This device is updating firmware. Please w ait... Dow nload Status : ID MAC Address Resul[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 254 upload sim_ms configuration Parameters configuration_to_tftp – Choose this parameter to upload configuration files from SIM members to a TFTP server. log_to_tftp - Choose this parameter to upload log files from SIM members to a TFTP server. <ipaddr> - Enter[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 255 DGS-3324SRi:4#upload sim_ms log_ to_tftp 10.55.47.1 D:log.txt all Command: upload sim_ms log_to_tftp 10.55.47.1 D:log.txt all This device is uploading log file. Please wait several minutes… Upload Status : ID MAC Address Result --- ----------------- -----------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 256 29 T IME AND SNTP C OMM ANDS The Simple Net work Time Protocol (SNTP) {an adapt ation of the Network Time Protocol (NTP)} commands in the Comm and Line Interface (CLI) are listed (along with the a ppropriate parameters) in the following table. Command Parameters co[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 257 disable sntp Purpose Disables SNTP server support. Syntax disable sntp Description This will disable SNTP s upport. SNTP service must be separately configured (see config sntp). Parameters None. Restrictions Only administrator-lev el users can issue this command. E[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 258 DGS-3324SRi:4#config sntp primary 10.1. 1.1 secondary 10.1.1.2 poll-interval 30 Command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Success. DGS-3324SRi:4# show sntp Purpose Used to display the SNTP information. Syntax show sntp Description Th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 259 To manually set system time and date settings: DGS-3324SRi:4#config time 30jun2003 16:30:30 Command: config time 30jun2003 16:30:30 Success. DGS-3324SRi:4# config time zone Purpose Used to determine the time zone used in order to adjust the system clock. Syntax con[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 260 config dst Description DST can be enabled and configured using this command. When enabled this will adjust the system clock to comply with any DST requirement. DST adjustment effects system time for both manually configured time and time set using SNTP service. Par[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 261 config dst subtract during the summertime. The possible offset times are 30, 60, 90, 120. The default value is 60. Restrictions Only administrator-lev el users can issue this command. Example usage: To configure daylight savings t ime on the Switch: DGS-3324SRi:4#c[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 262 30 ARP C OM MANDS The ARP comma nds in the Command Line Inte rface (CLI) are listed (along with the a ppropriate parameters) in the following table. Command Parameters create arpentry <ipaddr> <macaddr> delete arpentry [<ipaddr> | all] show arpent[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 263 Example Usage: To delete an entry of IP address 10.48.74.121 from the ARP table: DGS-3324SRi:4#delete arpentry 10.48.74.121 Command: delete arpentry 10.48.74.121 Success. DGS-3324SRi:4# config arp_aging time Purpose Used to configure the age-out timer for ARP table[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 264 To display the ARP table : DGS-3324SRi:4#show arpentry Command: show arpentry ARP Aging Time : 30 Interface IP Address MAC Address Type ------------- --------------- ----------------- --------------- System 10.0.0.0 FF-FF-FF-FF-FF-FF Local/Broadcast System 10.1.1.1[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 265 31 VRRP C OM MANDS VRRP or Virtual Routing Redundancy Prot ocol is a function on the Switch that dynami cally assigns responsibility for a virtual router to one of the VRRP routers on a LAN. The VRR P router that controls the IP address associated with a virtual ro[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 266 Example Usage: To enable VRRP globally on the Switch: DGS-3324SRi:4#enable vrrp Command: enable vrrp Success. DGS-3324SRi:4# Example usage: To enable the virtual IP address to be pi nged: DGS-3324SRi:4#enable vrrp ping Command: enable vrrp ping Success. DGS-3324SRi[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 267 create vrrp vrid Purpose To create a VRRP router on the Switch. Syntax create vrrp vrid <v rid 1-255> ipif <ipif_name 12> ipaddress <ipaddr> {state [enable | disable] | priority <int 1-254> | advertisement_interval <int 1-255> | preemp[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 268 create vrrp vrid critical_ip <ipaddr> - Enter the IP address of the physical device that will provide the most direct route to t he Internet or other critical network connections from this virt ual router. This must be a real IP address of a real device on th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 269 config vrrp vrid highest physical IP address as the Master router. The default value is 100. (The value of 255 is reserved for the router that owns the IP address associated with the virtual router and is therefore set automatically.) ipaddress <ipaddr> - Ent[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 270 config vrrp ipif Purpose To configure the authentication type for the VRRP routers of an IP interface. Syntax config vrrp ipif <ipif_name 12> [authtype [none | simple authdata <string 8> | ip authdata <string 16>] Description This command is used [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 271 Example Usage: To v iew the global VRRP settings currently implemented on the Switch (VRRP En abled): DGS-3324SRi:4#show vrrp Command: show vrrp Global VRRP :Enabled Non-ow ner response PING : Disabled Interface Name : System Authentication type : No Authentication[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 272 32 R OUTING T ABLE C OMMANDS The routing table comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create iproute <network_address> <i paddr> {<metric 1-65535>[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 273 create iproute default Purpose Used to create IP route entries to the Switch’s IP routing table. Syntax create iproute default <ipaddr> {<metric>} Description This command is used to create a default static IP route entry to the Switch’s IP routing [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 274 delete iproute default Purpose Used to delete a default IP route entry from the Switch’s IP routing table. Syntax delete iproute default <ipaddr> Description This command will delete an exis ting default entry from the Switch’s IP routing table. Parameter[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 275 33 R OUTE R EDISTRIBUTION C OMM ANDS The route redistribution comma nds in the Comma nd Line Interface (CLI) are listed (al ong with the appropriate parameters) in the following table. Command Parameters create route redistribute dst ospf src [static | rip | local][...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 276 Route Source Metric Metric Type RIP 0 to 16777214 mettype 1 mettype 2 Static 0 to 16777214 mettype 1 mettype 2 Local 0 to 16777214 mettype 1 mettype 2 Allowed Metric Type combinations are mettype 1 or mettype 2 . The metric value 0 above will be redistributed in OS[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 277 Routing inform ation source − OSPF and the Static Route table. Routing information will be redi stributed to RIP. The following table lists the allowed values for the ro uting metrics and the types (or forms) of the routin g information that will be redistr ibute[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 278 config route redistribute dst ospf src Parameters src [static | rip | local] − Allows the selection of the protocol of the source device. mettype − allows the selection of one of the methods for calculating the metric value. • Type-1 calculates the metric (fo[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 279 config route redistribute dst rip src information is then exchanged among the various routers according to the individual router s current routing protocol. The Switch can redistribute routing information between the OSPF and RIP routing protocols to all rout ers o[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 280 delete route redistribute Parameters dst [rip | ospf] − Allows the selection of the protocol on the destination device. The user may choose between RIP and OSPF. src [rip | static | local | ospf] − Allows the selection of the protocol on the source device. The [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 281 34 BOOTP R ELA Y C OM MANDS The BOOTP relay comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config bootp_relay {hops <val ue 1-16> | time <sec 0-65535>} config b[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 282 config bootp_relay add Purpose Used to add an IP destination address to the Switch’s BOOTP relay table. Syntax config bootp_relay add ipif <ipif_name 12> <ipaddr> Description This command adds an IP address as a destination to forward (relay) BOOTP pa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 283 enable bootp_relay Purpose Used to enable the BOOTP relay function on the Switch. Syntax enable bootp_relay Description This command, in combination with the disable bootp_relay command below, is used to enable and disable the BOOTP relay function on the Switch. Pa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 284 show bootp_relay Purpose Used to display the current BOOTP relay configuration. Syntax show bootp_relay {ipif <ipif_name 12>} Description This command will display the current BOOTP relay configuration for the Switch, or if an IP interf ace name is specified,[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 285 35 DNS R ELA Y C OMM ANDS The DNS relay comma nds in the Comm and Line Interface (CLI) ar e listed (along with the appropriate parameters) in the following table. Command Parameters config dnsr {[primary | secondary] nameserver <ipaddr> | [add | delete] stati[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 286 To add an entry domai n name dns1, IP address 10.43.21.12 to DNS stat ic table: DGS-3324SRi:4#config dnsr add static dns1 10.43.21.12 Command: config dnsr add static dns1 10.43.21.12 Success. DGS-3324SRi:4# Example Usage: To delete an entry dom ain name dns1, IP ad[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 287 DGS-3324SRi:4#enable dnsr cache Command: enable dnsr cache Success. DGS-3324SRi:4# Example Usage: To enable static ta ble lookup for DNS relay. DGS-3324SRi:4#enable dnsr static Command: enable dnsr static Success. DGS-3324SRi:4# disable dnsr Purpose Used to disable[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 288 DGS-3324SRi:4#disable dnsr cache Command: disable dnsr cache Success. DGS-3324SRi:4# Example Usage: To disable static t able lookup for DNS relay. DGS-3324SRi:4#disable dnsr static Command: disable dnsr static Success. DGS-3324SRi:4# show dnsr Purpose Used to displ[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 289 36 RIP C OM MANDS The RIP comma nds in the Command Line Inte rface (CLI) are listed (along with the a ppropriate param eters) in the following table. Command Parameters config rip [ipif <ipif_name 12> | a ll] {authentication [enable <password 16> | disa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 290 config rip rx_mode − Determines how received RIP packets will be interpreted – as RIP version V1 only, V2 Only , or V1 or V2 . This entry specifies which vers ion of the RIP protocol will be used to receive RIP packets. T he Disabled entry prevents the receptio[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 291 config rip timer Restrictions Only administrator-lev el users can issue this command. Example usage: To configure th e RIP timers for the switch: DGS-3324SRi:4#config rip timer update_interval 60 timeout_interval 60 garbage_collect_interval 60 Command: config rip t[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 292 DGS-3324SRi:4#disable rip Command: disable rip Success. DGS-3324SRi:4# show rip Purpose Used to display the RIP c onfiguration and statistics for the Switch. Syntax show rip {ipif <ipif_name 12>} Description This command will display the RIP configuration and[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 293 37 DVMRP C OM MANDS The DVMRP comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config dvmrp [ipif <ipif_name 12> | a ll] {metric <value 1-31> | probe <sec 1- 6[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 294 config dvmrp neighbor_timeout <second 1-65535> − The time period for which DVMRP will hold Neighbor R outer reports before issuing poison route messages. The default value is 35 seconds. state [enable | disable] − Allows DVMRP to be enabled or disabled. R[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 295 DGS-3324SRi:4#disable dvmrp Command: disable dvmrp Success. DGS-3324SRi:4# show dvmrp routing_table Purpose Used to display the current DVMRP routing table. Syntax show dvmrp routing table [ipaddress <netw ork_address>] Description The command is used to disp[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 296 Example Usage: To display DVMR P neighbor table: DGS-3324SRi:4#show dvmrp neighbor Command: show dvmrp neighbor DVMRP Neighbor Address Table Interface Neighbor Address Generation ID Expire Time --------------- ----------------------- ------------------- --------- S[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 297 show dvmrp Purpose Used to display the curr ent DVMRP settings on the Switch. Syntax show dvmrp {<ipif_name 12>} Description The command will display the current DVMRP routing table. Parameters <ipif_name 12> − This parameter will display DVMRP settin[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 298 38 PIM C OMM ANDS PIM or Protocol Indep endent Multicast is a method of forwarding traffic to m ulti cast groups over the network using any pre- existing unicast routing protocol, such as RIP or OSPF, set on routers within a multicast network. The xStack DGS/DXS-33[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 299 Register and Register Suppression Messages Multicast sources do not always join the intended receiver group. The first hop router (DR) can send multicast data without being the mem ber of a group or having a designated source, whic h essentially means it has no inf[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 300 Command Parameters config pim crp {holdtime <value 0-255> | priority <value 0-255> | wildcard_prefix_cnt [0 | 1]} create pim static_rp group <network address> rp <ipaddr> delete pim static_rp group <network address> show pim static_rp [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 301 DGS-3324SRi:4# disable pim Purpose Used to disable PIM function on the Switch. Syntax disable pim Description This command will disable PI M for the Switch. Any previously configured PIM settings will remain unchanged and may be enabled at a later time with the ena[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 302 config pim mode [dm | sm] - Used to select the type of PIM protocol to use, Sparse Mode (SM) or Dense Mode (DM). The default setting is DM. dr_priority <unsigned_int 0 – 4294967294> - Enter the priority of this IP interface to become the Designat ed Router [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 303 config pim register_suppression_time Purpose Used to configure the interval between the sending of register packets for the PIM protocol. Syntax config pim register_suppression_time <value 3-255> Description This command is to be confi gured for the first hop[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 304 DGS-3324SRi:4#create pim crp group 231.0.0.1/32 rp Trinity Command: create pim crp group 231.0.0.1/32 rp Trinity Success. DGS-3324SRi:4# delete pim crp Purpose To disable the Switch in becoming a possible candidate to be the Rendezvous Point (RP). Syntax delete pim[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 305 config pim crp the router having the higher IP address will become the RP. The user may set a priority between 0 – 255 with a default setting of 0. wildcard_prefix_cnt [0 | 1] - The user may set the Prefix Count value of the wildcard group address here by choosin[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 306 delete pim static_rp Purpose To remove the multicast gr oup IP address used in identifying the Rendezvous Point (RP). Syntax delete pim static_rp group <netw ork address> Description This command will remove t he multicast group IP address used in identifying[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 307 config pim rp_spt_threshold Purpose Used to configure the thre shold of register packets needed to enable the Shortest Path Tree (SPT). Syntax config pim rp_spt_threshold [<value 0-65535> | infinity] Description This command will set the threshold of register[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 308 DGS-3324SRi:4#config last_hop_spt_threshold 0 Command: config last_hop_spt_threshold 0 Success. DGS-3324SRi:4# show pim rpset Purpose Used to display the RP Set of the Switch. Syntax show pim rpset Description This command will display the information regarding the[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 309 C-RP Holdtime : 150 C-RP Priority : 2 C-RP w ildcard prefix count : 0 Group Interface --------------------- --------------------- 224.0.0.1/4 Trinity DGS-3324SRi:4# config pim cbsr Purpose Used to configure the settings for the Candidate Bootstrap Router and the pr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 310 DGS-3324SRi:4#config pim cbsr ipif Trinity priority 4 Command: config pim cbsr ipif Trinity priority 4 Success. DGS-3324SRi:4# Usage Example: To configure the hash mask l ength for the CBSR: DGS-3324SRi:4#config pim cbsr hash_masklen 30 Command: config pim cbsr has[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 311 DGS-3324SRi:4# show pim cbsr Command: show pim cbsr PIM Candidate-BSR Table C-BSR Hash Mask Len : 30 C-BSR Bootstrap Period : 2 Interface IP Address Priority --------------------- --------------------- ------------ Trinity 11.1.1.1/8 4 System 10.53.13.30/8 -1 (disa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 312 show pim neighbor Purpose Used to display PIM neighbors of the Switch. Syntax show pim neighbor {ipif <ipif_name12> | ipaddress <netw ork_address>} Description This command will display the PIM neighbor table for the Switch. Parameters <ipif_name 12&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 313 DGS-3324SRi:4# show pim ipmroute Command: show pim ipmroute PIM IP Multicast Route Table UA = Upstream AssertTimer AM = Assert Metric AMPref = Assert MetricPref ARB = Assert RPTBit Group Address Source Address UA AM AMPref ARB Flag Type ------------------ ---------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 314 DGS-3324SRi:4# create pim register_checksum_include_data rp_ address 11.1.1.1 Command: create pim register_checksum_include_data rp_ address 11.1.1.1 Success. DGS-3324SRi:4# delete pim register_checksum_include_data Purpose Used to disable the RPs that the Switch w[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 315 DGS-3324SRi:4# show pim register_checksum_include_data_rp_ list Command: show pim register_checksum_include_data_rp_ list RP Address ------------------------------------------- 11.1.1.1 Total Entries: 1 DGS-3324SRi:4#[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 316 39 IP M UL TICASTING C OMMANDS The IP multicasting comm ands in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters show ipmc cache {group <group>} {ipaddress <network_address>}[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 317 show ipmc Purpose Used to display the IP multicast interface table. Syntax show ipmc {ipif <ipif_name 12> | protocol [inactive | dvmrp | pim} Description This command will display the cu rrent IP multicast interface table. Parameters <ipif_name 12> − [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 318 40 MD5 C ONFIGURA TION C OMM ANDS The MD5 configuration comm ands in the Command Line Interface (C LI) are listed (along with the appropriate param eters) in the following table. Command Parameters create md5 key <key_id 1-255> <password 16> config md5 [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 319 To configure an MD5 Key password: DGS-3324SRi:4#config md5 key 1 taboo Command: config md5 key 1 taboo Success. DGS-3324SRi:4# delete md5 key Purpose Used to delete an entry in the MD5 key table. Syntax delete md5 key <key _id 1-255> Description This command [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 320 DGS-3324SRi:4#show md5 Command: show md5 MD5 Key Table Configurations Key-ID Key ------ ---------- 1 dlink 2 develop 3 fireball 4 intelligent Total Entries: 4 DGS-3324SRi:4#[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 321 41 OSPF C ONFIGURA TION C OMM ANDS The OSPF configuration comma nds in the Comma nd Line Interface (C LI) are listed (along with the appropriate parameters) in the following table. Command Parameters config ospf router_id <ipaddr> enable ospf disable ospf sho[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 322 Command Parameters show ospf all create ospf virtual_link <area_id> <nei ghbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none | simple <password 8> | md5 <key_id 1-255>]} config ospf virtua[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 323 DGS-3324SRi:4#enable ospf Command: enable ospf Success. DGS-3324SRi:4# disable ospf Purpose Used to disable OSPF on the Switch. Syntax disable ospf Description This command, in combination with the enable ospf command above, is used to enable and disable OSPF on th[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 324 To show OSPF state: DGS-3324SRi:4#show ospf Command: show ospf OSPF Router ID : 10.1.1.2 State : Enabled OSPF Interface Settings Interface IP Address Area ID State Link Metric Status ------------ ------------------ --------- -------- --------- --------- System 10.9[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 325 create ospf area Purpose Used to configure OSPF area settings. Syntax create ospf area <area_id> type [normal | stub {stub_summary [enable | disable] | metric <v alue 0-65535>}] Description This command is used to create an OSPF area and configure its s[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 326 DGS-3324SRi:4#delete ospf area 10.48.74.122 Command: delete ospf area 10.48.74.122 Success. DGS-3324SRi:4# config ospf area Purpose Used to configure an OSPF area’s settings. Syntax config ospf area <area_id> type [normal | stub {stub_summary [enable | disa[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 327 DGS-3324SRi:4#show ospf area Command: show ospf area Area ID Type Stub Import Summary LSA Stub Default Cost -------------- ------------- ------------------------------------ ------------------- 0.0.0.0 Normal None None 10.48.74.122 Stub Enabled Enabled Total Entrie[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 328 To delete an OSPF host route: DGS-3324SRi:4#delete ospf host_route 10.48.74.122 Command: delete ospf host_route 10.48.74.122 Success. DGS-3324SRi:4# config ospf host_route Purpose Used to configure OSPF host route settings. Syntax config ospf host_route <ipaddr&[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 329 Host Address Metric Area_ID --------------- --------------- ----------- 10.48.73.21 2 10.1.1.1 10.48.74.122 1 10.1.1.1 Total Entries: 2 DGS-3324SRi:4# create ospf aggregation Purpose Used to configure OSPF area aggregation settings. Syntax create ospf aggregation &[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 330 delete ospf aggregation Parameters <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <network_address> − The 32-bit number in the form of an IP address that uniquely[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 331 show ospf aggregation Purpose Used to display the curr ent OSPF area aggregation settings. Syntax show ospf aggregation {<area_id>} Description This command will display the current OSPF area aggregation settings. Parameters <area_id> − Enter this par[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 332 NOTE: When this command displays a “ * ” (a star symbol) in the OSPF LSDB table for the area_id or the Cost , this is interpreted as “no area ID” for external LSAs, and as “no cost given” for the advertised link. Usage Example: To display the link state[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 333 show ospf virtual_neighbor Purpose Used to display the current OSPF virtual neighbor router table. Syntax show ospf virtual_neighbor {<area_id> <neighbor id>} Description This command will display the current OSPF virtual neighbor router table. Paramete[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 334 config ospf ipif Parameters <ipif_name 12> − The name of the IP interface. area <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. priority <value> − The prio[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 335 config ospf all Purpose Used to configure all of the OSPF interfaces on the Switch at one time. Syntax config ospf all {area <area_id> | priority <value> | hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none | s[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 336 DGS-3324SRi:4#config ospf all state enable Command: config ospf all state enable Success. DGS-3324SRi:4# show ospf ipif Purpose Used to display the current OSPF interface settings for the specified interface name. Syntax show ospf ipif {<ipif_name 12>} Descri[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 337 show ospf all Parameters None. Restrictions None. Usage Example: To display the current OSPF interface setti ngs, for all OSPF interfaces on the Switch: DGS-3324SRi:4#show ospf all Command: show ospf all Interface Name: System IP Address: 10.42.73.10/8 (Link Up) Ne[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 338 create ospf virtual_link Parameters <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 339 config ospf virtual_link Parameters <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 340 delete ospf virtual_link Parameters <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 341 DGS-3324SRi:4#show ospf virtual_link Command: show ospf virtual_link Virtual Interface Configuration Transit Virtual Hello Dead Authentication Link Area ID Neighbor Router Interval Interval Status --------------- ---------------------- ------------ ----------- ----[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 342 42 R OUTE P REFERENCE C OMM ANDS Route Preference is a way for routers to se lect the best path when there are two or more different routes to the sam e destination from two different routing protocols. The m ajority of routing protocols are not compatible when use[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 343 config route preference Purpose Used to configure the rout e preference of each route type. Syntax config route preference [static | rip | ospfIntra | ospfInter | ospfExt1 | ospfExt2] <value 1-999> Description This command is used to se t the route preference[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 344 show route preference Parameters local – Enter this parameter to view the route preference settings for the local route. static - Enter this parameter to view the route preference settings for the static route. rip - Enter this parameter to view the route prefere[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 345 43 J UMBO F RAM E C OMMANDS Certain switches can support jum bo frames (frames larger than the standard Et hernet frame size of 1518 by tes). To transmit frames of up to 9K (and 9004 byt es tagged), the user can increase the m aximum transmission unit (MTU) size fr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 346 Example usage: To enable the jumbo fram e function on the Switch: DGS-3324SRi:4#disable jumbo_frame Command: disable jumbo_frame Success. DGS-3324SRi:4# show jumbo_frame Purpose Used to show the status of the jumbo frame function on the Switch. Syntax show jumbo_fr[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 347 44 F ILE S YSTEM C OM MANDS File System comm ands are used to configure files stored on a storage accessory located in the Switch, such as a CompactFlash card that can be used with the DGS-3324SRi only . These commands are based on DOS comm ands, cannot be used wit[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 348 Example usage: To view the storage media accessory information: DGS-3324SRi:4#show storage_media_info Command: show storage_media_info ------------------------------------------------ Drive Media_Ty pe Size Label FS_Type C: CF Card 30MB TEST FAT16 -----------------[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 349 Example usage: To copy a file: DGS-3324SRi:4#copy c:/abc.cfg c:/def.txt Command: copy c:/abc.cfg c:/def.txt processing...100 % Done!! DGS-3324SRi:4# dir Purpose Used to list the files and dire ctories on the storage media accessory. Syntax dir {<pathname 64>}[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 350 To delete a file: DGS-3324SRi:4#erase c:/aaa.cfg Command: erase c:/aaa.cfg processing...100 % Done!! DGS-3324SRi:4# format Purpose To format the storage media accessory Syntax format <drive> [FAT16] [fast | full | full_with_MBR] {<label_name 8>} Descrip[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 351 md Purpose To create a directory. Syntax md <pathname 64> Description This command is used to make a new directory on the storage media accessory. Parameters <pathname 64> - Enter the path and name of the file to be created. This entry cannot exceed 64 [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 352 rd Purpose Used to delete a directory from the storage media accessory. Syntax rd {<pathname 64>} Description This command is used to delete a directory listed on the storage media accessory. Parameters <pathname 64> - Enter the path and name of the dir[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 353 rename Purpose To rename a file. Syntax rename <source_path_filename 64> <target_path_filename 64> Description This command is used to rename a filename located on the storage media accessory. Parameters <source_path_filename 64> - Enter the path [...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 354 45 C OMM AND H ISTORY L IST The command history list com mands in the Co mmand Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters ? {<command>} show command_history config command_history <val[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 355 To display the parameters for a specific comm and: DGS-3324SRi:4#? config stp Command:? config stp Command: config stp Usage: {maxage <value 6-40> | maxhops <value1-20> | hellotime <v alue 1- 10> | forw arddelay <v alue 4-30> | txholdcount &[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 356 config command_history Purpose Used to configure the command history. Syntax config command_history <v alue 1-40> Description This command is used to configure the command history. Parameters <value 1-40> − The number of previously executed commands m[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 357 A T ECHNICAL S PECIFICA TIONS Physical and Environmental AC Input & External Redundant Power Supply: 100 – 120; 200 - 240 VAC, 50/60 Hz (internal universal power supply) Power Consumption: DGS-3324SR/ DGS-3324SRi - 90 watts maximum DXS-3326GSR – 88.09 watts[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 358 General Standards: IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.1D Spanning Tree IEEE 802.1w Rapid Spanning Tree IEEE 802.1s Multiple Spanning Tree IEEE 802.1 P/Q VLAN IEEE 802.1p Priority Queues IEEE 802.1x Port and MAC Ba[...]

xStack DGS/DXS-3300 Series Layer 3 Stackable Gigabit Ethernet S witch CLI Manual 359 Performance Transmission Method: Store-and-forward RAM Buffer: DGS-3324SR / DGS-3324SRi / DXS- 3326GSR – 2 MB per device DXS-3350SR – 4 MB per device Filtering Address Table: 16 K MAC addresses per device 3K IP addresses per device Packet Filtering/Forwarding R[...]