Dell C6220 II manuel d'utilisation

Dell PowerEdge C6220 II Systems Hardware Owner’ s Manual[...]

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better user of your computer . CAUTION: A CAUTION indicates pote ntial damage to hardware or loss of data if instructions are not foll owed. W ARNING: A WARNING indicates a potential for pr operty damage, personal injury , or death. Copyright © 2014 Dell[...]

Contents | 3 Contents 1 About Your System ...................................................................... 13 Accessing System Features during Startup .................................................. 13 Front-Panel Features and Indicators .............................................................. 14 Hard-Drive Indicator Patterns .......[...]

4 | Contents POST End Ev ent ......................................................................................... 44 POST Error Code Event ............................................................................ 45 BIOS Recovery Event ............................................................................... 45 ME Fail Event .........[...]

Contents | 5 SATA Configuration .................................................................................. 97 PCI Configuration ...................................................................................... 99 Embedded Network Devices ................................................................ . 102 ISCSI Remote Boot ..........[...]

6 | Contents Removing a 3.5-inch Hard-Drive Blank ................................................ 158 Installing a 3.5-inch Hard-Drive Blank ................................................. 158 Removing a 2.5-inch Hard-Drive Blank ................................................ 159 Installing a 2.5-inch Hard-Drive Blank .........................[...]

Contents | 7 Installing a Processor ............................................................................ 178 Interposer Extender for 2U Node ................................................................ .. 179 Removing the Interposer Extender for 2U Node ................................ . 179 Installing the Interposer Extender for 2U Nod[...]

8 | Contents Removing the LSI 9265-8i RAID Battery ............................................... 212 Installing the LSI 9265-8i RAID Battery ................................................ 213 Riser Card ......................................................................................................... 214 Optional Riser Cards ............[...]

Contents | 9 Removing the Memory Modules ........................................................... 240 Installing the Memory Modules ............................................................ 242 System Battery ................................................................................................ . 244 Replacing the System Battery ...[...]

10 | Contents Removing the 2.5-inch Hard Drive Backplane for Expander Configuration ................................ ........................................................... 287 Installing the 2.5-inch Hard Drive Backplane for Expander Configuration ................................ ................................................................[...]

Contents | 11 Troubleshooting a Wet System ..................................................................... 313 Troubleshooting a Damaged System ........................................................... 314 Troubleshooting the System Battery ............................................................ 315 Troubleshooting Power Supp lies ....[...]

12 | Contents Power Distribution Board 2 Connecto rs ................................ ...................... 339 Sensor Board Connectors .............................................................................. 339 Jumper Settings .............................................................................................. 340 System Configur[...]

1 About Y our System | 13 About Y our System Accessing System Fe atures during St artup The following keystrokes provide access to system features during startup. Note that the hot -keys of SAS/SA T A card or PXE support a re available in BIOS boot mode only . There is no hot - ke y to boot through the U EFI mode. Keystroke Description <F2> E[...]

14 | About Y our System Front-Panel Features an d Indicators This system is des igned with two types of system boa rds : C6220 II and C6220 . The system supports the following configurations : Figure 1-1. Front Panel − 3.5” x12 Hard Drives With Four System Boards (C6220/C6220 II R AID Card & Onboard SA T A Controller) Figure 1-2. Front Pane[...]

About Y our System | 15 Figure 1-3. Front Panel − 3 .5” x 6 Hard Drives With T wo System Board (C6220 Onboard SA T A Controller) Figure 1-4. Front Panel − 2 .5” x24 Hard Drives With Four System Boards (C6220/C6220 II RAID Card & Onboard SA T A Controller) Figure 1-5. Front Panel − 2.5” x16 Hard Drives With T wo System Boards (C6220/[...]

16 | About Y our System Figure 1-6. Front Panel − 2.5” x12 Hard Drives With two System Board (C6220/C6220 II Onboard SA T A Controller) Item Indicator , Button Or Connector Icon Description 1 P ower -on indicator/ system state indicator/ power button for system board 1 The power -o n indicator turns to gree n when the system power is on. The po[...]

About Y our System | 17 Item Indicator , Button Or Connector Icon Description 9 P ower -on indicator/ system state indicator/ power button for system board 3 NOTE: On ACPI-compliant operating systems, turning off the system using the power button causes the system to perform a graceful shutdown before power to the system is turned off. NOTE: T o fo[...]

18 | About Y our System Hard-Drive Indicat or Patterns Figure 1-7 . 3.5-inch Hard Drive Indicators 1 hard-drive activity indicator (green) 2 hard-drive status indicator (green and amber) Figure 1-8 . 2.5-inch Hard Drive Indicators 1 hard-drive status indicator (green and amber) 2 hard-drive activity indicator (green)[...]

About Y our System | 19 T able 1-1. Hard-Drive Status Ind icators − For 3.5" /2.5” Direct Hard- Drive Backplane Controller Hard Drive T ype Function Activity LED Status LED Green Green Amber Onboard Controller SA T A2 Drive on-line Off/ Blinking when active On Off F ail Off On Off LSI 9265 /LSI 2008 /LSI 9210 SAS /SA T A2 Slot Empty Off Of[...]

20 | About Y our System T able 1-2 . Hard-Drive Status Indicators − For 2.5” Hard-Drive Backplane for Expander Configuration Controller Hard Drive T y pe Function Activity LED Status LED Green Green Amber LSI 9265 /LSI 2008 /LSI 9210 SAS /SA T A2 Slot Empty Off Off Off Drive On-line Blinking when active On Off Drive Identify / Pr eparing for Re[...]

About Y our System | 21 Service Tag The Service T ag locations for 1U node, 2U node , a nd the cha ssis are as follows: Figure 1-9 Service T a g Location for 1U Node Figure 1- 10 Service T ag Location for 2U Node[...]

22 | About Y our System Figure 1- 11 Service T ag Location on the Left Front Panel Figure 1- 12 Service T ag Location on the Chassis[...]

About Y our System | 23 The linkage of 12 hard drives for four system boards is presented as below . Refer to Front-Panel Features an d Indicators on page 14 for other configuration s. Figure 1- 13 Service T ag Linkage NOTE: HDD’ s under warran ty would be linked to the appropriate service tag of the node.[...]

24 | About Y our System Back Panel Features and Indicators Figure 1- 14 Back Panel with Four System Boards Figure 1- 15 Back Panel with T wo System Boards Item Indicator , Button Or Connector Icon Description 1 P ower supply 2 12 00 W/1400 W 2 P ower supply 1 12 00 W/1400 W 3 dual USB port Connect USB devices to the system. The ports ar e USB 2.0 -[...]

About Y our System | 25 Item Indicator , Button Or Connector Icon Description and system board. Ligh ts amber when the system needs attention due to a problem. 5 LAN connector 1 Embedded 10/100/1000 NIC connectors. 6 LAN connector 2 Embedded 10/100/1000 NIC connectors. 7 Management port Dedicated management port. 8 Serial port Connects a serial dev[...]

26 | About Y our System Item Indicator , Button Or Connector Icon Description system using the power button causes the system to perform a graceful shutdown before power to the system is turned off. NOTE: T o force an ungraceful shutdown, press and hold the power button for five seconds. System-Board Assembly Confi gurations Figure 1- 16 . Enumerat[...]

About Y our System | 27 Figure 1- 19 . Enumeration One System Board for 1U Node Figure 1- 20 . Enumeration T w o System Boa rds for 2U No de Figure 1- 21 . Enumeration One System Board for 2U Node[...]

28 | About Y our System LAN Indicator Codes Figure 1- 22 . LAN Indicators 1 speed indicator 2 link/activity indicator C om p on e n t I nd i ca t o r C on d it i o n Speed indicator Solid amber Linking at 100Mbps speed Solid green Li nking at 1Gbps speed (maximum) Blinking gree n Linking at 1Gbps speed. Activity is presen t: - Pr e OS POST - OS wit[...]

About Y our System | 29 Figure 1- 23 . LAN Indicators (Manage ment Port) 1 speed indicator 2 link/activity indicator C om p on e n t I nd i ca t o r C on d it i o n Speed indicator Blinking gree n Linking at 100Mbps speed (maximum) Blinking amber Linking at 10Mbps speed Link/activity indicator Solid gree n No access Blinking gree n LAN accessing / [...]

30 | About Y our System Power and System Board In dicat or Codes The LEDs on the system front panel and back panel display status codes during system startu p. F or location of the LEDs on th e front panel, see F igure 1-1 for 3.5” hard drive and F igure 1-4 for 2.5” hard drive systems. F or location of the LEDs on the back panel, see F igure 1[...]

About Y our System | 31 Power Supply Indicator C odes 1400W Power Supp ly Figure 1- 24 . Power Supply Status Indicator 1 power supply 2 AC power indicator C om p on e n t I nd i ca t o r C on d it i o n AC power indicator Solid gree n System is on. Blinking gree n System is off. Off AC off.[...]

32 | About Y our System 1200W Power Supp ly Figure 1- 25 . Power Supply Status Indicator 1 power supply 2 AC power Indicator C om p on e n t I nd i ca t o r C on d it i o n AC power indicator Solid gree n AC on. Y ellow F ault. Off AC off.[...]

About Y our System | 33 BMC Heart Beat L ED The system board provides BMC heart beat LED ( LED17 ) for BMC debugs. The BMC heart beat L ED is green. When the system AC power i s connected , th e LE D lights . When B MC firmware is ready , the BMC heart beat LED blinks. Figure 1- 26 . BMC Heart Beat LED on the System Board C6220 II Figure 1- 27 . BM[...]

34 | About Y our System Post Error Code Collecting System Event Log (SEL) for Investigation Whenever possible, th e BIOS will output the current boot progress codes on the video screen. Progress codes are 3 2- bit quantities plus optional da ta. The 32 -bit numbers include clas s, subclass, and operation inf ormation. The class and subclass fields [...]

About Y our System | 35 Er r or C o d e Er r or M e s s ag e Er r or C a us e R ec o v er y M e t h o d 00 12h Local Console Output Error Video device initialization failed Make sure video device is well 00 13h ISA IO Controller Error ISA device's IO initialization failed Make sure ISA device is well 0014h ISA IO Resource Confli ct ISA device&[...]

36 | About Y our System Er r or C o d e Er r or M e s s ag e Er r or C a us e R ec o v er y M e t h o d Error KB device is well 0023h Memory Correctable Error Memory correctable error be detected Reset power or change new memory 0024h Memory Uncorrectable Error Memory un correctable error be detected Reset power or change new memory 0025h Memory No[...]

About Y our System | 37 Er r or C o d e Er r or M e s s ag e Er r or C a us e R ec o v er y M e t h o d 002Fh No Microcode be Updated Pro ces sor microcode load failed Check pr oc essor stepping and microcode are match 8018h Sparing Mode is not be Configured!! Please check Memory Configuration!! Memory sparing mode failed Change memory configuratio[...]

38 | About Y our System System Event Log Processor Erro r Message: “P rocessor Senso r , IERR erro r , Processor 1” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification 5 Sensor[...]

About Y our System | 39 Memory ECC Message: “M emory Sensor , Correctable ECC error , SBE warn ing threshold, CPU1 DIMM_A1” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification [...]

40 | About Y our System B yt e Fi e l d V al ue D es c ri p t i on 10 Event Data3 XXh DIMM bit-map locatation of bits Bit 0=1: DIMM1 error event Bit 1=1: DIMM2 error event … Bit7=1: DIMM8 error event PCI -E Error Message: “Cri tical Interrupt Sensor , PCI PERR, Device#, F unction#, Bus# “ B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLu[...]

About Y our System | 41 IOH Core Error Message: “Cri tical Interrup t Sens or , Fatal E rror , xx xx bit, QPI[0] Error ” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification. 5 [...]

42 | About Y our System SB Error Message: “Cri tical Interrupt Sensor , Correctable, MCU P a rity Error ” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification. 5 Sensor T ype 13[...]

About Y our System | 43 POST Start Even t Message: “System Even t, POST starts with BIOS xx .xx.xx” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 0 2h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification. 5 Sensor T ype 12h Sys[...]

44 | About Y our System POST End Event B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification. 5 Sensor T ype 12h System Event 6 Sensor Number 85h POST End (depend on platform) 7 Even[...]

About Y our System | 45 POST Error Code Event Message: “System Firmware P rogress, POST error code: UBLBh.” B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h 3 Generator ID 01h Generated by BIOS 4 Event Message F ormat V ersion 04h Event Message F ormat Revision. 04h for this specification. 5 Sensor T ype [...]

46 | About Y our System B yt e Fi e l d V al ue D es c ri p t i on 8 Event Data1 AXh 01h: OEM BIOS recovery Event 9 Event Data2 XXh 01h:Start Recovery 02h:Recovery Success 03h:Load I mage F ail 04h:Signed F ail 10 Event Data3 FFh FFh: Not Pr esent ME Fail Event B yt e Fi e l d V al ue D es c ri p t i on 1 NetF unLun 10h 2 Platform Event Command 02h[...]

About Y our System | 47 Sensor Data Record Event Log Onl y : the sensor w ill be only used to explain eve nt log, and will show disable about sensor state. R ec o rd ID S en s or Nu m b e r S en s or Na m e S en s or Ty p e Ev e nt / R e a di n g Ty p e O ff s et 0004h 0x01 SEL F ullness Event Logging Disabled (10h) Sensor -specific (6Fh) SI: 67h S[...]

48 | About Y our System R ec o rd ID S en s or Nu m b e r S en s or Na m e S en s or Ty p e Ev e nt / R e a di n g Ty p e O ff s et 0007h 0x06 5V V oltage (02h) Thre shold (01h) SI: 7Fh SC: 59h AM: 7A95h DM: 7A95h TM: 3F3Fh 0006h 0x07 5V Standby V oltage (02h) Thre shold (01h) SI: 7Fh SC: 59h AM: 7A95h DM: 7A95h TM: 3F3Fh 0009h 0x08 3.3V V oltage ([...]

About Y our System | 49 R ec o rd ID S en s or Nu m b e r S en s or Na m e S en s or Ty p e Ev e nt / R e a di n g Ty p e O ff s et 000Dh 0x42 CPU2 T emp T emperature (01h) Thre shold (01h) SI: 7Fh SC: 68h AM: 0A95h DM: 7A95h TM: 3838h 000Eh 0x43 DIMM ZONE 1 T emp T emperature (01h) Thre shold (01h) SI: 7Fh SC: 68h AM: 0A95h DM: 7A95h TM: 3838h 000[...]

50 | About Y our System R ec o rd ID S en s or Nu m b e r S en s or Na m e S en s or Ty p e Ev e nt / R e a di n g Ty p e O ff s et N/A 0x2F Session Audit (Event Log Only) Session A udit (2Ah) N/A N/A 0019h 0xA3 Sys Pwr Monitor System ACPI P ower State (22h) Sensor -specific (6 Fh) SI: 01h SC: 40h AM: 0021h DM: 0000h RM: 0021h Dynamic 0xB6 PSU1 Sta[...]

About Y our System | 51 R ec o rd ID S en s or Nu m b e r S en s or Na m e S en s or Ty p e Ev e nt / R e a di n g Ty p e O ff s et Dynamic 0x64 12V V oltage(02h) Thre shold(01h) V ariable Dynamic 0xB1 Inlet T emp T emperature (01h) Thre shold(01h) V ariable Dynamic 0xB3 Input V oltage V oltage(02h) Thre shold(01h) V ariable Dynamic 0xB4 Input Curr[...]

52 | About Y our System Other Information You M ay Need W ARNING: See the safety and regulatory inf ormation that shipped with your system. Warranty information may be included within t his document or as a separate document. The Getting Started Guide provides an over view of rack install ation, system features, setting up your system, a nd technic[...]

About Y our System | 53  1U node can’t support PCI-E and Mezzanine card at the same time.  2U node only can be install ed one PCI-E and Mezzanine card by each MB. Matrix of Fresh Air Support of 1U node with 3.5 ” HDD configuration 1 0 ~ 30 °C 3 5 °C 40 °C 45 °C 60W 1 2* HD D Fu ll c o nf ig ur ati o n 1 0* HD D Fu ll c o nf ig ur ati [...]

54 | About Y our System 115W 1 2* HD D Fu ll c o nf ig ur ati o n 1 2* HD D Fu ll c o nf ig ur ati o n 8 *H DD Fu ll c o nf ig ur ati o n 4* HD D 1 6* DI MM, w/ o P CI - E ca rd , w/ o me zz an in e c ar d 130W (8 c or e) 1 2* HD D Fu ll c o nf ig ur ati o n 1 0 * HD D Fu ll c o nf ig ur ati o n 4 *H DD Fu ll c o nf ig ur ati o n 4* HD D 1 6* DI MM[...]

About Y our System | 55 Matrix of Fresh Air Support of 1U node with 2.5 ” HDD configuration 1 0 ~ 30 °C 3 5 °C 40 °C 45 °C 60W 2 4* HD D Fu ll c o nf ig ur ati o n 2 4* HD D Fu ll c o nf ig ur ati o n 8 *H DD Fu ll c o nf ig ur ati o n 4* HD D 1 6* DI MM, w/ o PC I- E c ar d, w/ o me zz an in e c ar d 70W 2 4* HD D Fu ll c o nf ig ur ati o n [...]

56 | About Y our System w/ o me zz an in e c ar d 130W (4 c or e) 16 * HD D Fu ll c o nf ig ur ati o n 4 *H DD 1 6* DI MM, w/ o PC I -E c ar d, w/ 1* m ez za ni ne c ar d no t su pp or t no t su pp or t 135W 8 *H DD Fu ll c o nf ig ur ati o n 4 *H DD 1 6* DI MM, w/ o PC I- E c ar d, w/ o m ez za ni ne c ar d no t su pp or t no t su pp or t[...]

About Y our System | 57 Matrix of Fresh Air Support of 2U node with 3.5 ” HDD configuration 1 0 ~ 30 °C 3 5 °C 40 °C 45 °C 60W 1 2* HD D Fu ll c o nf ig ur ati o n 1 2* HD D Fu ll c o nf ig ur ati o n 1 0* HD D Fu ll c o nf ig ur ati o n 4 * HD D 1 6* DI MM, w/ 2* PC I- E ca rd , w/ o me zz an in e c ar d 70W 1 2* HD D Fu ll c o nf ig ur ati [...]

58 | About Y our System 135W 1 2* HD D Fu ll c o nf ig ur ati o n 8 *H DD Fu ll c o nf ig ur ati o n 4 * HD D 1 6* DI MM, w/ 2* P CI -E c ar d, w/ o me zz an in e c ar d no t su pp or t Matrix of Fresh Air Support of 2U node with 2.5 ” HDD configuration 1 0 ~ 30 °C 3 5 °C 40 °C 45 °C 60W 2 4* HD D Fu ll c o nf ig ur ati o n 2 4* HD D Fu ll c [...]

About Y our System | 59 w/ o me zz an in e c ar d 130W (4 c or e) 2 4* HD D Fu ll c o nf ig ur ati o n 2 4* HD D Fu ll c o nf ig ur ati o n 1 6* HD D Fu ll c o nf ig ur ati o n 8* HD D 1 6* DI MM, w/ 1 *P CI -E c ar d, w/ o me zz an in e 135W 8 *H DD Fu ll c o nf ig ur ati o n 1 6* HD D Fu ll c o nf ig ur ati o n 4 *H DD 1 6* DI MM, w/ 2* P CI -E c[...]

60 | About Y our System C6220 II System Conf iguration Limi tations by Intel Xeon Process or E5-2600 v2 produc t family System Configuration Limitations by Intel Xeon Processor E5-2600 v2 product family Processor Bin 1U (1-4 Node) 3.5” HDDs 2U (1-2 N ode) 3.5” HDDs 1U (1-4 Node) 2.5” HDDs 2U (1-2 Node) 2.5” HDDs 6 0W E5 -2 63 0L v2 1 0* HDD[...]

About Y our System | 61 System Configuration Limitations by Intel Xeon Processor E5-2600 v2 product family Processor Bin 1U (1-4 Node) 3.5” HDDs 2U (1-2 N ode) 3.5” HDDs 1U (1-4 Node) 2.5” HDDs 2U (1-2 Node) 2.5” HDDs 9 5W E5 - 26 60 v2 E5 -2 65 0v 2 E5 -2 64 0 v2 1 2* HDD s Fu ll c on f i gu ra t io n 1 2* HDD s Fu ll c on f i gu ra t io n[...]

62 | About Y our System C6220 II Fresh Ai r Support Matrix of Fresh Air Support of 1U node with 3.5” HDD configuration C PU Po we r 1 0 ~ 3 0 ° C 3 5 ° C 4 0 ° C 4 5 ° C 6 0W 12 * HD Ds Fu ll c o nf ig ur ati o n 1 0* H DD s Fu ll c o nf ig ur ati o n 4 * HD Ds 1 6 D IM Ms w/ o m ez za ni ne c ar d no t su pp or t 7 0W 12 * HD Ds Fu ll c o nf[...]

About Y our System | 63 Matrix of Fresh Air Support of 1U node with 3.5” HDD configuration C PU Po we r 1 0 ~ 3 0 ° C 3 5 ° C 4 0 ° C 4 5 ° C E5 -2 60 0 13 0W ( 8 co re ) E5 -2 60 0 v2 1 30W ( 12 /1 0 c o r e) 12 * HD Ds Fu ll c o nf ig ur ati o n 8 * HD Ds Fu ll c o nf ig ur ati o n 4 * HD Ds 16 D I MM s w/ o m ez za ni ne or PC I- E ca rd n[...]

64 | About Y our System Matrix of Fresh Air Support of 1U node with 2 .5” HDD configuration CPU P owe r 10 ~ 30 ° C 35 ° C 40 ° C 45 ° C 8 0W 24 * HD Ds Fu ll c o nf ig ur ati o n 24 * HD Ds Fu ll c o nf ig ur ati o n 20 * HD Ds Fu ll c o nf ig ur ati o n 12 * HD Ds 16 D IM Ms w/ o m ez za ni ne or PC I- E c ar d 9 5W 24 * HD Ds Fu ll c o nf [...]

About Y our System | 65 Matrix of Fresh Air Support of 2 U node with 3.5” HDD configu ration CPU P owe r 10 ~ 30 ° C 35 ° C 40 ° C 45 ° C 6 0W 12 * HD Ds Fu ll c o nf ig ur ati o n 8 * HD Ds 1 6 D IM Ms wi tho ut m ez za ni ne c ar d 4* HD Ds 8 DI MM s 1 PC I- E ca r d 7 0W 12 * HD Ds Fu ll c o nf ig ur ati o n 8 * HD Ds Fu ll c o nf ig ur at[...]

66 | About Y our System Matrix of Fresh Air Support of 1U node with 2 .5” HDD configuration CPU P owe r 10 ~ 30 ° C 35 ° C 40 ° C 45 ° C E5 -2 60 0 13 5W 8 * HD Ds Fu ll c o nf ig ur ati o n 8 * HD Ds 8 DI MM s w/ o PC I -E c ar d , w/ o m ez za ni ne c ar d no t su pp or t no t su pp or t Matrix of Fresh Air Support of 2U node with 2 .5” H[...]

About Y our System | 67 Matrix of Fresh Air Support of 2U node with 2 .5” HDD configuration CPU P ower 10 ~ 30 ° C 35 ° C 40 ° C 45 ° C E5 -2 60 0 13 0W ( 8 co re ) E5 -2 60 0 v2 1 30W ( 12 /1 0 c o r e) 24 * HD Ds Fu ll c o nf ig ur ati o n 24 * HD Ds Fu ll c o nf ig ur ati o n 8 * HD Ds 1 6 D IM Ms wi tho ut m ez za ni ne o r P CI -E c ar d[...]

2 68 | Using the System Setup Program Using the System Setup Program Start Menu The system employs the l atest Ins yde BIOS, which is s tored in Flash memory . The Flas h memory supports the Plug a nd Play specifica tion, and contains a System Setup program, the P ower On Self T est (POST) routine, and the PCI auto-confi guration utility . This sys[...]

Using the System Setup Program | 69 Boot Manager During BIOS POST , press F11 can enter Boot Manager to select boot device.[...]

70 | Using the System Setup Program If UEFI OS was installed, the UEFI OS partition will be present on the boot option.  Boot Manager – UEFI Mode[...]

Using the System Setup Program | 71  Boot Manager – Legacy Mode Console Redirection The console redirection allows a remote user to diagnose a nd fix problems on a server , which has not succes sfully booted the operatin g system. The centerpiece of the cons ole redirection is the BIOS Console. The BIOS Console is a F lash ROM-resident utility[...]

72 | Using the System Setup Program After reconnecting the consol e, if the display is a bnormal it is recommended that you reflash the screen by pressing the <Ctrl><R>. The following are different modes for Console Redirection: 1 External serial port . 2 Internal serial connector as Serial Over LAN ( SOL). 3 BMC SOL. Enabling and Con f[...]

Using the System Setup Program | 73  Remote Access: enabled  Serial port number: COM2 as SOL  Serial P ort Mode: 11 5200 8, n, 1  Flow Control: None  Redirection After BIOS POST : Always  Te rminal T yp e: VT1 00 T o do thi s, see “ Remote Acce ss Configuration ” on page 114 . Note that the host and client need to ha ve the sa[...]

74 | Using the System Setup Program  IP Address: 192.168.001.003  Subnet Mask: 255. 255.255.000  Gateway Address: 000.000.000.0 00 T o do thi s, see “ Set B MC LAN Configura tion ” on page 113 . Note that the host and client need to ha ve the same network s ection. T o ena ble SOL feature in the mode of Sha red-NIC, perform the foll ow[...]

Using the System Setup Program | 75 Serial P ort Connection List Signal T ype Setup Option OS Setting Output Remote Access Serial Port Number Serial Port Address Serial Console Redirec tion Enabled COM1 3F8h/2F8h ttyS0 Serial P ort Enabled COM1 2F8h/3F8h ttyS1 BMC Serial Over LAN Enabled COM2 as SOL 3F8h/2F8h ttyS1 Management P ort Enabled COM2 as [...]

76 | Using the System Setup Program Main Menu The main menu dis plays information about your system boards and BIOS. Main Screen NOTE: The options for the System Setup program change based on the system configuration. NOTE: The System Setup program defaults are listed under their respective options in the following sections, where applicable . Opti[...]

Using the System Setup Program | 77 Option Description Service T ag Displays the service tag of the product. T he service tag field should match what is physically on the service t ag of the node. Asset T ag Displays the asset tag of the product. BIOS V ersion Displays the BIOS version. MRC V ersion Displays the version of MR C. ME V ersion Display[...]

78 | Using the System Setup Program Advanced Menu This option displays a table o f items that defines a dvanced information about your system. CAUTION: Making incorrect settings to items on these pages may cause the system to malfunction. Unless you h ave experience adjusting these items, we recommend that you leave these settin gs at the default v[...]

Using the System Setup Program | 79 Power Managem ent Scroll to this item and press Enter to view the follo wing screen: O pt i o n D es c ri p t i o n P ower Management ( OS Control default) This field sets the System P ower Management to Maximum P erformance mode, OS Control mode, or Node Manager mode. CP U P ower Capping ( P -state 0 default) Th[...]

80 | Using the System Setup Program O pt i o n D es c ri p t i o n ( Balanced default) mode. This option works while the OS is not supported power management control of processor only . Chassis Power Ma nagement O pt i o n D es c ri p t i on Chassis PSU Configuration The option provides management an d monitoring of PSUs and the minimum set of r eq[...]

Using the System Setup Program | 81 Chassis PSU Configur ation 1 Enter the server BIOS setu p screen. 2 Enter Advanced/Power M anagement /Chassis Power Management / Chassis PSU Configuration, and the following options are for Chassis PSU Configuration functio ns :  Required P ower Su pplies - Sets the number of po wer supplies that is required t[...]

82 | Using the System Setup Program O pt i o n D es c ri p t i on Requir ed P ower Supplies This is the number of power supplied that is re quired to run the servers in the chassis. (The default is refe rring from FCB F/W thru BMC by IPMI command) Redundant P ower Supplies This is the number of power supplied that is redun dant. (The default is ref[...]

Using the System Setup Program | 83 PSU’s capacity . (i .e. based on the number of PSUs and the ma x capacity of each PSU) The m ax capaci ty of each PSU is 1100 W att or 140 0W att supportable. Therefore P ower B udget will not ex ceed 2660 W att in this system. (1 400 * 2(max number of PSUs in chassis ) * 0.95 = 2660 W att)  Chassis L evel C[...]

84 | Using the System Setup Program[...]

Using the System Setup Program | 85 O pt i o n D es c ri p t i on P ower Budget Shows this chassis available power wattage. Chassis Level Capping ( Disabled default) Enables or disables the Chassis Level Capping. (The default is refe rring from BMC) Chassis P ower Capping The capping value range limits at power budget of PSU design. (These is no de[...]

86 | Using the System Setup Program Emergen cy Throttling When the power emergency process starts, an event will be genera ted by FCB. And there is a record on the SELs. FCB monitors the error cond itions such as "PSU l ost over than the number of Redunda nt PSU " , "PSU fail event (OC, UV , OT , …) " , "F an fa il" [...]

Using the System Setup Program | 87 O pt i on D es c ri p t i o n Sled Level P olicy ( Chassis Level default) Sets the sled level policy when emer gency throttling event trigger .  Chassis Level: The option allows overriding the chassis level policy for a specifi c server .  Throttling: The compute sled throttling when emer gency throttling e[...]

88 | Using the System Setup Program CPU Configuration Scroll to this item and press Enter to view the follo wing screen:[...]

Using the System Setup Program | 89[...]

90 | Using the System Setup Program O pt i o n D es c ri p t i on Active P rocessor Cores ( All Cores default) This field controls the number of enabled core in each processor . F reque ncy Ratio ( Auto defau lt) Sets fre quency multiplier as maximum level. Downgrade- set multiplier 1~3 levels. Max CPUID V alue Limit ( Disabled default) Some OS, wh[...]

Using the System Setup Program | 91 O pt i o n D es c ri p t i on C-States ( Enabled default) Enabled - The processor can operate in all available P ower C States. Disabled - There are no C States available for the processor . C1E State ( Enabled default) Enabled - The C1-E is enabled by default. Disabled - The C1-E is disabled by us er s in their [...]

92 | Using the System Setup Program O pt i o n D es c ri p t i on (Scorpion, Nemo only) ( Off default) Dial. CPU R APL Small Dial (Scorpion, Nemo only) ( 0 default) P ower Limit (W att#) = CPU RA PL Big Dial – CPU RA PL Small Dial. Pr efetch Configuration Configur es Pre fetch. (Invisible if CPU do not support.)[...]

Using the System Setup Program | 93 Prefetc h Configuratio n O pt i o n D es c ri p t i on Adjacent Cache P refetch ( Enabled default) Includes MLC Spatial P refet cher . Disabled - The processor will only fetch the ca che line that contains the data curr ently requir ed by processor . Enabled - Enables the processor to fetch the adjacent cache lin[...]

94 | Using the System Setup Program Memory Configur ation Scroll to this item and press Enter to view the follo wing scree n: O pt i o n D es c r ip t i o n Memory F requency ( Auto defau lt) Memory fre quency selections in MHz. Memory Throttling Mode ( Enabled default) Enables or disables the memory to run in clos ed-loop thermal throttling mode. [...]

Using the System Setup Program | 95 O pt i o n D es c r ip t i o n copied to the spar e rank and the failed rank is disabled . W ith memory sparing en abled, the system memory available to the operating system is reduce d by one rank per channel. F or example, in a dual-processor configuration with sixteen 32 GB quad-rank DIMMs, the available syste[...]

96 | Using the System Setup Program O pt i o n D es c r ip t i o n NOTE: BIOS will auto restrict selection if DIMM does not support low voltage. NUMA Support ( Enabled default) Disabled – for BIOS setup to allow users en able the node interleave option. This is for NUMA systems that allow memory interleaving across all processor nodes. Enabled ?[...]

Using the System Setup Program | 97 SA T A Configuration Scroll to this item and press Enter to view the follo wing screen:[...]

98 | Using the System Setup Program O pt i o n D es c ri p t i on Embedded SA T A Controller ( AHCI default) Off – Disables the SA T A controller . The token applies to the first on-board SA T A controll er . IDE – Enables the SA T A controller . Sets the device class code as IDE and uses PCI IRQ (referr ed as Native mode). This tok en applies [...]

Using the System Setup Program | 99 O pt i o n D es c ri p t i on Embedded SA T A Link Rate ( A uto default) Aut o – Sets the SA T A link rate at maximum as 6.0 Gbps. 1.5 Gbps – Sets the SA T A link r ate at minimum as 1.5 Gbps. F or power consumption. 3.0 Gpbs – Sets the SA T A link rate at minimum as 3.0 Gbps. SA T A P ort 0 ( Auto defau lt[...]

100 | Using the System Setup Prog ram NOTE: The PCI-E Gen2 x16 slot 1 and slot 2 are supported up to Gen2 5.0 Gigabits bandwidth. If user inserts Gen3 .0 devices into the 2 slots that will only train at Gen 2.0 speed, not Gen 3.0. O pt i o n D es c ri p t i on Embedded Network Devices Configur e embedded network devices. NIC Enumeration ( Onboard d[...]

Using the System Setup Program | 101 O pt i o n D es c ri p t i on PCIe Generation ( Gen3 default) Sets the PCI signaling rate at Gen3 8.0/Gen2 5.0/Gen1 2.5 Gigabits bandwidth. VT for Dir ect I/O ( Disabled default) Enables/Disables I/O VTd Error . SR -IO V G lobal Enable ( Disabled default) Enables/Disables BIOS support for SRIO V devices. I/O A T[...]

102 | Using the System Setup Prog ram O pt i o n D es c ri p t i on ( Disabled default) network controller re ceives a magic packet. Note: Reboot on WOL featur e i s opened by customized, need EEPORM supported. Embedded Networ k Devices O pt i o n D es c ri p t i on Embedded NIC1 ( Enabled with PXE default) Disabled – Disables the system’s prim[...]

Using the System Setup Program | 103 O pt i o n D es c ri p t i on iSCSI Remote Boot – Enables NIC1 with iSCSI Remote Boot. Embedded NIC2 ( Enabled without PXE default) Disabled – Disables the system’s secondary embedded network interface controller . Enabled with PXE – Enables the system’s secondary embedded network interface controller [...]

104 | Using the System Setup Prog ram ISCSI Remote Boot O pt i o n D es c ri p t i on iSCSI Initiator Name Th e worldwide unique name if the initiator . Only iqn. F ormat is accepted. Enable DHCP ( Disabled default) Disables/Enables DHCP . Initiator IP Address Initiator Subnet Mask Gateway Enters IP address in dotted-decimal notati on. T arget IP T[...]

Using the System Setup Program | 105 Active State Powe r Management Configuration O pt i o n D es c ri p t i on PCIe Slot ASPM ( Disabled default) Disabled - Controls the level of ASPM supported on the PCI-E Link of port 2. All entry is disabled. L1 - Controls the level of ASPM supported on the given PCI-E Link of port 2. L1 entry is enabled. Onboa[...]

106 | Using the System Setup Prog ram O pt i o n D es c ri p t i on L1 - Controls the level of ASPM supported on the given PCI-E Link of port11. L1 entry is enabled. NB -SB Link ASPM ( L1 default) Disabled - Controls the level of ASPM supported on the NB-SB. All entry is disabled. L1 - Controls the level of ASPM supported on the NB- SB. L1 entry is[...]

Using the System Setup Program | 107 USB Configura tion Scroll to this item and press Enter to view the follo wing screen: O pt i o n D es c ri p t i on Embedded USB Controller ( Enabled default) Causes the BIOS to e nable/disable the built-in USB controller at system startup. USB P ort with BMC ( Enabled default) This feature allows the users to e[...]

108 | Using the System Setup Prog ram Security Menu This page enables you to set the security parame ters. Scroll to this item and press Enter to view the follo wing screen: NOTE: A warning message popps up, which needs users to confirm the requirement before enabling “ Prevent Back-flash ” .[...]

Using the System Setup Program | 109 O pt i o n D es c ri p t i on Supervisor P as sword Indicates whether a supervisor password has been set. If the password has been installed, Installed is displayed. If not, Not Installed is displayed. User P assword Indicates whether a supervisor password has been set . If the password has been installed, Insta[...]

110 | Using the System Setup Prog ram O pt i o n D es c ri p t i on retype d it correctly . If the password confirmation is incorrec t, an error message appears. The password is stored in NVRAM after ezPOR T completes. The password is r equire d at boot time, or when the user enters the Setup utility . Change User P as swor d Installs or changes th[...]

Using the System Setup Program | 111 Server Menu This page enables you to configure Server parameters. Scroll to this item and press Enter to view the follo wing screen: O pt i o n D es c ri p t i on Status of BMC Displays the BMC status. IPMI Specification V ersion Displays the IPMI specification version. BMC F irmware V ersion Displays the BMC fi[...]

112 | Using the System Setup Prog ram O pt i o n D es c ri p t i on driver installation. Set BMC LAN Configuration Inputs for Set LAN Configuration comman d. Each item in this group may tak e considerable amount of time. Remote Access Configuration Configur es Remote Access. Restore on AC P ower Loss ( P ower On default) P ower Off - After an AC po[...]

Using the System Setup Program | 113 Set BMC LAN Conf iguration Select Set BMC LAN Confi guration to view the fol lowing s ubmenu: O pt i o n D es c ri p t i on Channel Number Displays the channel number . Channel Number Status Displays the channel number status. BMC LAN P ort Configuration ( Shared-NIC default) Sets BMC LAN P ort to dedicated-NIC [...]

114 | Using the System Setup Prog ram Remote Access C onfiguration Select Remote Access Configuration t o view the follo wing submenu:[...]

Using the System Setup Program | 115 O pt i o n D es c ri p t i on Remote Access ( Enabled default) Disabled - Serial Console Redir ection Off. Enabled - Enables Serial Console Redir ection. Serial P ort Number ( COM2 as SOL default) COM1- serial Console Redirection On, output to COM1. See also token D7h. COM2 as SOL-serial Console redir ection On,[...]

116 | Using the System Setup Prog ram Boot Menu This page enables you to set POST boot para meters. Scroll to this item and press Enter to view the follo wing screen: O pt i o n D es c ri p t i on Quiet Boot ( Enabled default) Enabled – Enables the display of the splash or summary scree n, rather than the detail of the POST flow . Disabled- Disab[...]

Using the System Setup Program | 117 O pt i o n D es c ri p t i on ( BIOS default) F irmware Interface (UEFI). Legacy – Enables booting to Legacy mode, ensures compatibility with operating systems that do not support UEFI. Boot T ype Or der Configur es Boot T ype Order , N etwork/ Hard Disk/ RA ID/ USB Storage/ CD/ DVD ROM. Exit Menu Scroll to th[...]

118 | Using the System Setup Prog ram O pt i o n D es c ri p t i on Save Changes and Exit Exits system setup after saving the changes. F10 key can be used for this operation. Discard Chan ges and Exit Exits system setup without saving any changes. ESC key can be used for this operation. Save Changes Save your changes and without exi ting system. Di[...]

Using the System Setup Program | 119 of BMC LAN port as 10.106.42.120) T able 2-1. The D4 T oken T a b le T o k en S e tu p o pt i o n D es c r i pt i o n 002D Em b ed d e d NI C 1 En a bl e s t he s ys t e m ’s p r im a r y e m b ed d e d n e tw o r k in t er f a c e c o n tr o l le r ( f ul l -f u nc t i on ) , in c l ud i n g i t s P XE b oo t[...]

120 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 008C Embedde d US B Con t ro ll er Cau se s the BI OS t o enab le the b u il t- in USB cont ro ll e r a t sy st em st artup. 008 D Embedde d USB Con t ro ll er Cau se s the BI OS t o di s ab le th e bu il t- in USB cont ro ll e r a t sy st em st artup. 00 A1 Re s[...]

Using the System Setup Program | 121 T o k en S e tu p o pt i o n D es c r i pt i o n 00D8 Load Optimal De f au lts Reque st s a opt imal de f au lt o f SETUP va lu e s o n the ne xt boot. 00 FE Legac y USB Support Sy st e m do es no t provide le ga c y US B suppor t fo r operat ing sy st e m. 00 FF Legac y US B Support Sy st e m prov id es le ga c[...]

122 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 0139 Embedded SA T A Co nt ro ll er Enables the SA T A con t ro ll er . Sets the devi ce class c od e as RA ID and e x ecute s the R AID Option ROM. This tok e n app li e s to the f ir st on-boar d S A TA c on t ro ll er . 013E Mem or y Re mapp ing (3 GB~4GB) Mem[...]

Using the System Setup Program | 123 T o k en S e tu p o pt i o n D es c r i pt i o n 0170 Embed ded SAS Contro ller Enable s the SA S contr oller . Set s the device class co de as AHCI/R AID an d ex ecute s the R AID Option ROM. Thi s toke n app lies to on-board SAS c ontrol ler . 0171 Ad ja cent Ca che L ine P re fe tc h The pro cesso r will on l[...]

124 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 01DB Embedde d NIC2 Enables NIC 2 w it h iSCS I Remote B oo t. 01 EA Tu rb o M od e Dis ab les Intel' s pro ces so r a ll ow s th e proc es sor c or e to in c re as e it s frequen cy . 01 EB Tu rb o M od e Enables Intel' s p ro ce sso r a ll ow s the pr[...]

Using the System Setup Program | 125 T o k en S e tu p o pt i o n D es c r i pt i o n 022E B oo t M od e Enables boot ing to lega cy m od e, ensure s c ompatibi lit y wi th operat ing s ys te ms t hat d o no t support UE FI. 0231 Active P ro c es sor Core s A ll f ou r cor es o f th e pro cess o r ar e en ab le d. This i s app li c ab le for Q ua d[...]

126 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 025F M ir ror M od e Mem or y Operatin g M od e se t to supp ort Mem or y mirror in g. 0260 Advance d ECC M od e Mem or y Operatin g M od e se t to supp ort Advanced E CC , i.e. Lock st ep, Ch ip kill. 026A Coher ent HT L ink Speed S et s to support HyperT ranspo[...]

Using the System Setup Program | 127 T o k en S e tu p o pt i o n D es c r i pt i o n 02 A9 DR A M P re f et c he r Dis ab les DR AM re fere nce s f rom tr ig gering DR AM pref et c h requests. 02 AA DR A M P re f et c he r Tu rn s on th e DR AM pr efetc h unit i n th e N orthbr id ge . 02 AB HW P re fe tc h T ra ini n g o n SW Dis ab les har dw ar[...]

128 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 02C8 Da t a Reuse Optimization S et s t o dis ab le fo r ener g y e ff ic ie n cy . 02C9 QPI Bandwidth Pr io rit y S et s t o Com pu te (Def au lt) for co mp ut at io n-inten siv e applicat io ns. 02CA QPI Bandwidth Pr io rit y S et s t o I/O for I/ O-in t en siv[...]

Using the System Setup Program | 129 T o k en S e tu p o pt i o n D es c r i pt i o n 4027 Manu fa ct ur ing M od e Dis ab le t he m an uf ac t ur ing m od e t o bypas s POST tasks/me m or y t es t s an d F1/F2 pro m pt s o n s pe cifi c error messages . Used b y Manu fa ct ur in g; no t fo r general c us tome r use. 4033 S er ial P or t M od e Con[...]

130 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 480A Cr 6 St ate The C 6 is dis ab led by user in t heir own li ab ility . Th ere will be w arning me ss ag e in bo th the BIO S Setu p he lp te xt an d the pop up me ss ag e w hen th e op tion i s ch ang in g . 480B C6 St ate The C 6 is enabled b y de f au lt. 4[...]

Using the System Setup Program | 131 T o k en S e tu p o pt i o n D es c r i pt i o n 4823 Mem or y F re quency De tect s the mem or y runn ing spee d fr om H/ W d es igne d ( SP D, mem or y populatio n) . 4824 Mem or y F re quency S et s me mo ry runni ng speed up s t o 800 M Hz . 4825 Mem or y F re quency S et s me mo r y runn ing speed up s t o [...]

132 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 4830 HD D Sec ur ity E ra se S et s th e HD D Sec ur ity F reez e Loc k t o a ll o f HDDs. 4831 HD D Sec ur ity E ra se Un lo ck s t h e HD D Sec ur ity F reeze Lo c k to a ll of HDD s. 4832 A HC I-AMD Support s AM D in bo x A HC I dr iver . 4833 A HC I- MS Suppo[...]

Using the System Setup Program | 133 T o k en S e tu p o pt i o n D es c r i pt i o n 4846 Onboar d LAN ASPM Con t ro ls the le ve l o f ASPM supp orte d t o on-boar d LAN . A ll en tr y disa bled. 4847 Onboar d LAN ASPM Con t ro ls the le ve l o f ASPM supp orte d t o on-boar d LAN . L0 s entr y en ab le d. 4848 Onboar d LAN ASPM Con t ro ls the l[...]

134 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 4851 Mezz an ine Slot ASPM Con t ro ls the le ve l o f ASPM suppor te d o n Mez zan ine S lo t. L0s en tr y do w n st re am an d L1 enab le d. 4852 NB-SB L ink ASPM Con t ro ls the le ve l o f ASPM supp orte d on th e NB-SB . A ll ent r y dis ab l ed . 4853 NB-SB[...]

Using the System Setup Program | 135 T o k en S e tu p o pt i o n D es c r i pt i o n 485E Reboot on W OL (R O W ) Dis ab les the RO W in de f au l t, Re b oo t on WOL(RO W) is a f ea t ur e wh ic h repurpose s the tradit iona l W ak e on LAN (WOL) sign al t o reboo t the motherboar d. D ur ing s ys te m is in S 0/ S3 st ate, w he n a W OL packet i[...]

136 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 4880 Mezz an ine Slot This f ea t ur e will allow th e user s to e le ct ri cally enab le Mezz an ine Slot. 4881 1s t B oo t Device S et s Har d Di s k a s f ir st boo t device . 4882 1s t B oo t Device S et s RAI D a s f ir st bo ot device . 4883 1s t B oo t Dev[...]

Using the System Setup Program | 137 T o k en S e tu p o pt i o n D es c r i pt i o n 48 A3 BM C LAN P or t Con f ig uration S et s BM C LAN P or t to Shar ed-NIC. 48 A4 BM C NI C IP Source S et s BM C LAN t o ge t LAN IP fro m St ati c mo de . 48 A5 BM C NI C I P Source S et s BM C LAN t o ge t LAN IP fro m DHCP m od e. 48 A6 IP v 6 M od e Dis ab [...]

138 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 48 B4 NMI o n Error Enables BI OS to gene rat e NMI w hen PCI-E un correct ab le errors occu r . 48 B5 Mem or y Operat ing V olt ag e I nd icate s a ll DI MM s in the s ys te m ar e oper ating at 1.2 5 vo l ts . 48C0 F re quenc y Ra t io S et s fre quency multipl[...]

Using the System Setup Program | 139 T o k en S e tu p o pt i o n D es c r i pt i o n 48D A S av e Cu st o mi ze d De f au lts Save s curr en t s et t in g s to cu st omize d de f au lts o f SE TU P on ne xt bo ot. 48DB N/A Reque st s max imum performanc e s et t in gs of SE TUP va lu e s on the ne x t boot. 48DC N/A Reque st s a ene rg y ef fi c i[...]

140 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 48 E9 N/A The HDD4 is used fo r 1st device of PXE boo t on th e ne xt boot. 48 EA N/A The HDD5 is used fo r 1st devic e of PXE boo t on th e ne xt boot. 48 EB N/A The HDD6 is used fo r 1st device of PXE boo t on th e ne xt boot. 48 EC N/A The R AI D HDD 1 is use [...]

Using the System Setup Program | 141 T o k en S e tu p o pt i o n D es c r i pt i o n 48 F9 N/A The R AI D HDD1 4 i s use d for 1s t d ev ic e o f PXE boot on the ne xt boot. 48 FA N/A The R AI D HDD1 5 i s use d for 1s t d ev ic e o f PXE boot on the ne xt boot. 48 FB N/A The R AI D HDD1 6 i s use d for 1s t d ev ic e o f PXE boot on the ne xt boo[...]

142 | Using the System Setup Prog ram T o k en S e tu p o pt i o n D es c r i pt i o n 4916 Chassi s Level P olicy Default, set chassis level policy as thrott ling when Emergenc y Throttling event trigger . 4917 Chassis Level P olicy Set chassis level policy as power off when Emer gency Throttling event trigger . 4918 N/ A Default, disables clock s[...]

Using the System Setup Program | 143 Broadcast Get Device ID App (0x06) 0x01 M Y Cold Reset App (0x06) 0x02 O Y W arm Reset App (0x06) 0x03 O Get Self T est Results App (0x06) 0x04 M Y Manufacturing T est On App (0x06) 0x05 O Y Set A CPI P ower State App (0x06) 0x06 O Y Get ACPI P ower State App (0x06) 0x07 O Y Get Device GUID App (0x06) 0x08 O Y G[...]

144 | Using the System Setup Prog ram Set System Info P arameters App (0x06) 0x58 O Y Get System Info P arameters App (0x06) 0x59 O Y Get Channel A uthentication Capabilities App (0x06) 0x38 O Y Get Session Challenge App (0x06) 0x39 O Y Active Session App (0x06) 0x3A O Y Set Session P rivilege Level App (0x06) 0x3B O Y Close Session App (0x06) 0x3C[...]

Using the System Setup Program | 145 Chassis Control Chassis (0x00) 0x02 O Y Chassis Reset Chassis (0x00) 0x03 O Chassis Identify Chassis (0x00) 0x04 O Set F ront P anel Button Chassis (0x00) 0x0A O Set Chassis Capabilities Chassis (0x00) 0x05 O Y Set P ower Restore P olicy Chassis (0x00) 0x06 O Set P ower Cycle Interval Chassis (0x00) 0x0B O Get S[...]

146 | Using the System Setup Prog ram Get Sensor Event Enable S/E (0x04) 0x29 O Y Re -arm Sensor Events S/E (0x04) 0x2A O Y Get Sensor Event Status S/E (0x04) 0x2B O Y Get Sensor Reading S/E (0x04) 0x2D M Y Set Sensor T ype S/E (0x04) 0x2E O Get Sensor T yp e S/E (0x04) 0x2F O Set Sensor Reading And Event Statu s S/E (0x04) 0x30 O Y FRU Device Comm[...]

Using the System Setup Program | 147 Get SEL T ime Storage (0x0A) 0x48 M Y Set SEL Ti me Storage (0x0A) 0x49 M Y Get Au xiliary Log Status Storage (0x0A) 0x5A O Set Auxi liary Log Status Storage (0x0A) 0x5B O Get SEL T ime UTC Offset Storage (0x0A) 0x5C O Set SEL Ti me UTC Offset Storage (0x0A) 0x5D O LAN Device Commands Set LAN Configuration P ara[...]

148 | Using the System Setup Prog ram F irmware Update Phase 1 F irmware (0x08) 0x10 O Y F irmware Update Phase 2 F irmware (0x08) 0x11 O Y F irmware Update Phase 3 F irmware (0x08) 0x21 O Y Get F irmware Update Status F irmware (0x08) 0x12 O Y Get F irmware V ersion F irmware (0x08) 0x13 O Y Set F irmware Update Status F irmware (0x08) 0x16 O Y T [...]

Using the System Setup Program | 149 S et u p M e n u Se t t in g Ma x i mu m P er f or m a n c e ( 4 8D B ) En e rg y E ff i c i e nc y ( 48 D C) S et u p P a g e S et t i ng O pt i o n D 4 T o k en O pt i o n D 4 T o k en Memory Operating V oltage 1.5 V 02B6 1.35V /1.25V 02B7 /48B5 SA T A Configuration Embedded SA T A Link State Aut o 4834 1.5 Gb[...]

3 150 | Removing and Installing System Components Re mo ving and Inst alling System Components Safety Instructions W ARNING: Whenever you need to lift the system, get others to assist you. T o avoid injury , do not attempt to lift the system by yourself. W ARNING: Working on systems that are still connected to a power supply can be extremely danger[...]

Removing and Installing System Componen ts | 151 T o a void injury to yourself or da mage to the s ystem, follow these gui delines:  Always dis connect the system from the po wer outlet whenever y ou are working inside the system.  If possible, wear a grounded wrist strap as you work inside the system. Or discharge any static electricity by t[...]

152 | Removing and Installing System Components 4 Grasp cover on both the si des with your palm on the tracti on pad, slide out and lift the cover a way from the system. See Figure 3-1 . Figure 3-1. Opening and Closing the Syste m 1 traction pad 2 system cover 3 securing screw 4 cover release latch lock Closing the System 1 Place the cover on the c[...]

Removing and Installing System Componen ts | 153 Inside the System CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product document ation, or as directed by the online or telephone service and support team. Damage due to servi cing that is [...]

154 | Removing and Installing System Components Figure 3-3. Inside the System with 2U Node 1 system board assembly (2) 2 power supply (2) 3 power distribution board (2) 4 cooling fan (4) 5 hard-drive bay 6 hard drive (12) Cooling Fans Removing a Coo ling Fan W ARNING: Do not attempt to op erate the system without the cooling fans. W ARNING: The coo[...]

Removing and Installing System Componen ts | 155 1 It is recommended to turn off the system, i ncluding any attached peripherals, and dis connect the s ystem from its electrical outlet. 2 Open the system. See “ Opening the System ” on page 151 . 3 Disconnect the fan’s pow er cable from the power distribut ion board 1 . Note the routing of th [...]

156 | Removing and Installing System Components 5 Disconnect the fan cable fro m the fan connect or on the cooling -fa n cage. See Figure 3 -5 . 6 Lift the cooling fan with the sponge out of the co oling -fan cage. See Figure 3-5 . Figure 3-5. Removing and Installing a Coo ling Fan 1 cooling-fan cage 2 cooling fan 1 3 cooling fan 2 4 sponge 5 cooli[...]

Removing and Installing System Componen ts | 157 Installing a Cooli ng Fan CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform tro ubleshooting and simple repairs as authorized i n your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cing[...]

158 | Removing and Installing System Components Hard Drives Removing a 3.5-inch Ha rd-Drive Blank CAUTION: T o maintain pr oper system cooling, all empty hard- drive bays must have drive blanks installed. NOTE: This section is applicable to systems with hot -swa ppable hard drives only . 1 Pull the hard-drive blan k out of the hard -drive bay. See [...]

Removing and Installing System Componen ts | 159 Removing a 2.5-inch Ha rd-Drive Blank CAUTION: T o maintain pr oper system cooling, all empty hard- drive bays must have drive blanks installed. NOTE: This section is applicable to systems with hot -swa ppable hard drives only . 1 Pull the handle to remov e the 2 .5-inch ha rd-drive blank out of the [...]

160 | Removing and Installing System Components Removing a Hard-Drive Ca rrier The installation a nd removal procedures for the 3.5 -inch hard drive and the 2.5-inch hard drive are similar . F ollowing is an example s howing the replacement procedure of a 3.5 -inch hard drive. CAUTION: Many repairs may only be do ne by a certified service technicia[...]

Removing and Installing System Componen ts | 161 Installing a Hard-Dri ve Carrier CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to serv[...]

162 | Removing and Installing System Components 1 Remove the four s crews. See Fi gure 3-9. 2 Lift the hard drive out of th e hard -drive carrier. Figure 3-9. Removing and Installing a Hard Drive from the Hard -Drive Carrier 1 hard drive 2 screw (4) 3 hard-drive carrier CAUTION: When installing a hard -drive carrier , ensure that the adjacent driv [...]

Removing and Installing System Componen ts | 163 Installing a Hard D rive into a Hard-Drive Carrier 1 Place the hard drive into the har d-drive carrier. S ee Figure 3-9 . 2 Secure the hard drive to the hard -drive carrier with four screws. See Figure 3-9 . Installing a 2.5” SS D into a 3.5” Hard-Dri ve Carrier 1 Place the 2.5” SSD into the 2.[...]

164 | Removing and Installing System Components 3 Place the adapter as sembly into the 3 .5” hard -drive carrier. See Fi gure 3- 11 . 4 Secure the adapter assembly to the 3 .5” hard- drive carrier with three mach screws. S ee Figure 3 - 11 Figure 3- 11 . Removing and Installing a adapter asse mbly from the Hard -Drive Carrier 1 adapter assembly[...]

Removing and Installing System Componen ts | 165 5 Do not install screws in the two screw holes on the side of S SD, which are occupied by the ligh t pipe. S ee Figure 3- 12 . Figure 3- 12 . Screw Holes on the side of SSD and occupied by the Light Pipe NOTE: 1 This operation is only for 2 .5” SSD. Don’t install any 2 .5” HDD into the adapter;[...]

166 | Removing and Installing System Components Power Supplies T able 3-1. PSU and Sys tem Board Support Matrix PSU T w o S y st em B o a r ds Fo u r S y s te m B oa r d s 1400 W Up to two 130W processors / MB three h ard drives / MB eight memory modules / MB Up to one 130W processor / MB, two hard drives / MB two memory modules / MB 12 00 W Up to [...]

Removing and Installing System Componen ts | 167 3 Press the release lever and us ing the handle, slide the p ower supply out of the system. See Fi gure 3- 13 . NOTE: Removing the power supply may require considerable force. Figure 3- 13 . Removing and Installing a Power Supp ly 1 power supply 2 release lever 3 handle Installing a Powe r Supply CAU[...]

168 | Removing and Installing System Components 2 Slide the new power supply i nto the chassis until the power supply is fully seated and the relea se lever snaps into place. See Figure 3 - 13 . 3 Connect the power cabl e to the power supply a nd plug the cable i nto a power outlet. NOTE: When installing a new power supply in a sys tem with two pow[...]

Removing and Installing System Componen ts | 169 System-Board Assembly Removing a Dummy Sys t em-Board T ray CAUTION: Many re pairs may only be done by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and suppo[...]

170 | Removing and Installing System Components Installing a Dum my System-Board T ray 1 Slide the dummy syst em-board tra y into the chassis until it snaps into place. See Figure 3- 14 . 2 Replace the screw that secure s the retaining latch. See Figure 3- 14 . Removing a System-B oard Assembly 1 It is recommended to turn off the system board by pr[...]

Removing and Installing System Componen ts | 171 Figure 3- 15 . Removing and Installing a System-Board Assembly 1 retaining latch 2 screw 3 handle 4 system-board assembly Installing a System -Board Assembly CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as auth[...]

172 | Removing and Installing System Components Air Baffle Removing the Air Ba ffle CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authoriz ed in your product documentation, or as directe d by the online or telephone service and support team. Damage due to s[...]

Removing and Installing System Componen ts | 173 Installing the Air Baff le CAUTION: Many repairs may only be do ne by a certified ser vice technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cin[...]

174 | Removing and Installing System Components Figure 3- 18 . The T op View of the Installed Air Baffle 3 Replace the system- board assembly. See "Installing a System-Board Assembly" on page 171 . Heat Sinks Removing the Heat Si nk CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform trouble[...]

Removing and Installing System Componen ts | 1 75 1 Remove the system-b oard assembly. See “ R emoving a Syst em-Board Assembly" on page 170 . W ARNING: The heat sink may be hot to touch for some ti me after the system has been powered down. Allow the heat sin k to cool before removing it. CAUTION: Never remove the heat sin k from a processo[...]

176 | Removing and Installing System Components Installing the Hea t Sink CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentatio n, or as directed by the online or telephone service and support team. Damage due to servi cing t[...]

Removing and Installing System Componen ts | 177 2 Remove the heat sink, s ee "Removing the Hea t Sink" on page 174 . CAUTION: The processor is held in its so cket under strong pressure. Be aware that the release lever can spri ng up suddenly if not firmly grasped . 3 Position your thumbs firmly over the process or socket -release levers [...]

178 | Removing and Installing System Components Installing a Proces sor CAUTION: Many re pairs may only be done by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cing tha[...]

Removing and Installing System Componen ts | 179 CAUTION: Using excess thermal gr ease can cause grease to contact the processor shield, which can cause contamin ation of the processor socket. 8 Place the heat sink on the pr ocessor. See Figure 3 - 19 . 9 Using a Phillips screwdriver, tighten the hea t-sink reten tion screws. See Figure 3- 19 . 10 [...]

180 | Removing and Installing System Components Assembly" on page 170 . 2 Disconnect all the cables fro m the interposer extender for 2U node . See Figure 5 - 11 . 3 Remove the screws that secur e the interposer extender for 2U node to the interposer-exte nder tray. See Figure 3- 21 . 4 Lift the interposer extender for 2 U node out of the inte[...]

Removing and Installing System Componen ts | 181 2 Replace the screws that secure the interposer extender for 2U node to the interposer-exte nder tray for 2U node. See Fi gure 3- 21 . 3 Reconnect all the cables to t he interposer ex tender for 2U node. See Figure 5- 11 . 4 Replace the system- board assembly. See "Installing a System-Board Asse[...]

182 | Removing and Installing System Components Removing the In terposer Extende r T ray for 2U Node 1 Remove the system-b oard assembly. See “ R emoving a Syst em-Board Assembly" on page 170 . 2 Remove the interpos er extender for 2U node. See F igure 3- 21 . 3 Remove the screws that secur e the interposer -extender tray to the system board[...]

Removing and Installing System Componen ts | 183 Installing the Inte rposer Extender for 2U Node T ray 1 Place the interposer- extender tray into the system board . See Figure 3 - 22 . 2 Replace the screws that secur e the interposer extender tra y for 2U node to the system board. See Figure 3 - 22 . 3 Replace the interposer exte nder for 2U node. [...]

184 | Removing and Installing System Components Expansion-Card Assem bly and Ex pansion Card Removing the Expan sion Card for 1U N ode 1 Remove the system-b oard assembly. See “ R emoving a Syst em-Board Assembly" on page 170 . 2 Remove the four screws that secure the expansion -ca rd assembly. See Figure 3- 23 . 3 Lift the expansion -card a[...]

Removing and Installing System Componen ts | 185 4 Remove the screw securi ng the expansion card . See Figure 3- 24 . 5 Grasp the expansion card by its edges, and ca refully remove it from the riser card . See Figure 3- 24 . If you are removing the ca rd permanently, instal l a n expansion-ca rd slot cover over the emp ty expansion slot opening, an[...]

186 | Removing and Installing System Components Installing the Expan sion Card for 1U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directed by the online or telephone servi ce and support team. Damage du[...]

Removing and Installing System Componen ts | 187 Removing the Expan sion Card for 2U N ode CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simpl e repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage d[...]

188 | Removing and Installing System Components Figure 3- 26 . Removing the Expansion-card Lock Cover for 2U Node 1 expansion-card assembly 2 screw (4) 3 expansion-card lock cover 4 expansion card 6 Remove the screw securi ng the expansi on card. See Figure 3- 27 . 7 Grasp the expansion card by its edges, and ca refully remove it from the riser car[...]

Removing and Installing System Componen ts | 189 Figure 3- 27 . Removing the Expansion Card for 2U No de 1 expansion card 2 screw 3 riser card[...]

190 | Removing and Installing System Components 8 Install the expansion -card slot cover and screw securing th e expansion - card bracket. See F igure 3- 28 . Figure 3- 28 . Installing the Expansion-card Slot Cover for 2U Node 1 screw 2 expansion-card slot cover 3 expansion-card bracket[...]

Removing and Installing System Componen ts | 191 9 Install the expans ion-card lock cover a nd screws secur ing to the expansion card bracket. See Fi gure 3- 29 . Figure 3- 29 . Installing the Expansion-card Lock Cover for 2U Node 1 expansion-card bracket 2 screw (4) 3 expansion-card lock cover Installing the Expan sion Card for 2U Node CAUTION: Ma[...]

192 | Removing and Installing System Components Assembly" on page 170 . 4 Remove the four s crews that secure the expans ion-ca rd assembly. 5 Lift the expansion -card assembly away fr om the system -board ass embly. 6 Remove the screw securi ng the filler bracket. 7 Grasp the filler bracket by its edges, and caref ully remove i t from the ris[...]

Removing and Installing System Componen ts | 193 PCI -E Slot Priority 1. The C6220 I I system board is designed with onl y o ne mezzanine ca rd slot, which is PCI- E Gen 3 x8 mezzanine slot 3, s o there i s no priority concern. 2. Since the C6220 II system board can be assembled o n to th e 1U system- board tray or 2U system -board tray, follow the[...]

194 | Removing and Installing System Components RAID Card The installation a nd removal procedures and cable routing for the R AID Cards including LSI 9265-8i with BBU , LSI 92 10 -8i HBA and LSI 9285- 8e with BBU are similar; refer to the indications for detai ls. Summary of LSI 9265-8i with RAID Batte ry , LSI 9210-8i HBA and LSI 9285 -8e with RA[...]

Removing and Installing System Componen ts | 195 LSI 9265 -8i Card NOTE: The LSI 9265 -8i card assembly should include the RA ID B at te ry interposer card which is connected to the RAID batte ry. The illustrations in this section are just for your removal and installation reference . For more information of the RAID battery, see “ LSI 9265-8i R [...]

196 | Removing and Installing System Components Figure 3- 30 . Removing the LSI 9265-8i Card Assembly for 1U Node 1 LSI 9265 - 8i -card assembly 2 screw (4) 3 system-board assembly 5 Remove the screw securi ng the LSI 926 5 -8i card. See Figure 3- 31 . 6 Grasp the LSI 926 5-8i card by its edges, and carefully remove it from the riser card . See Fig[...]

Removing and Installing System Componen ts | 197 Figure 3- 31 . Removing the LSI 9265-8i Card 1 expansion-card slot cover 2 screw 3 LSI 9265 -8i card 4 riser card[...]

198 | Removing and Installing System Components Installing the LS I 9265 -8i Card for 1U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damag [...]

Removing and Installing System Componen ts | 199 10 Replace the four screws that secure the LSI 9265 -8i card assembly. 11 Install the system-board ass embly. See "Instal ling a System- Board Assembly" on page 171 . Cable Routing for LS I 9265-8i Card (1U N ode) 1 Connect the mini - SAS cable to the LSI 9265-8i card, and connect the other[...]

200 | Removing and Installing System Components Figure 3- 32 . Cable Routing for LSI 9265-8i Card (1U Node) I t em C a bl e F ro m ( LS I 9 2 6 5- 8i C a r d) To ( RA I D B at t er y a nd S ys t em B o ar d ) Mini- SAS cable Mini-SA S connector 0~3(J2B1 ) SAS/SATA input connector 0 Mini-S AS /SGPIO cable Mini-SA S connector 4~7 (J2B 2) SAS/SATA inp[...]

Removing and Installing System Componen ts | 201 4 Press down on th e cables, and en sure the cables a re routed lower than the height of the C PU heat sinks. Figure 3- 33 . Cable Rou ting Down (1U Node)[...]

202 | Removing and Installing System Components Removing the LSI 9265 -8i Card for 2U N ode NOTE: The LSI 9265 -8i card assembly should include the BBU interposer card which is connected to the LSI 9265-8i RAID battery. The illustrations in this section are just for your removal and ins tallation reference. For more information of the LSI 9265-8i R[...]

Removing and Installing System Componen ts | 203 Figure 3- 34 . Removing the LSI 9265-8i Card Assembly for 2U Node 1 LSI 9265 - 8i -card assembly 2 screw (5) 3 system-board assembly 5 Re move the four s crews securing the LSI 9265 - 8i card lock cover . See F igure 3- 35 . 6 Remove the LSI 92 65-8i ca rd lock cover. SeeF igure 3- 35 .[...]

204 | Removing and Installing System Components Figure 3- 35 . Removing the LSI 9265-8i Card Lock Cover 1 LSI 9265- 8i -card assembly 2 screws (4) 3 expansion-card lock cover[...]

Removing and Installing System Componen ts | 205 7 Remove the screw securi ng the LSI 926 5 -8i card. See Figure 3- 36 . 8 Grasp the LSI 926 5-8i card by its edges, and carefully remove it from the riser card . See Figure 3 - 36 . If you are removing the ca rd permanently, instal l a metal filler bracket over the empty expansi on slot opening, and [...]

206 | Removing and Installing System Components Installing the LS I 9265 -8i Card for 2U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the onlin e or telephone service and support team. Damag[...]

Removing and Installing System Componen ts | 207 11 Install the system-board ass embly. See “ Installing a System-Boa rd Assembly ” on page 171 . Cable Routing for LS I 9265-8i Card (2U Node) 1 Connect the mini -SAS&SGPIO cable to the LSI 9265 - 8i card, and connect the other end of the cable to the c orresponding co nnectors on the interpo[...]

208 | Removing and Installing System Components NOTE: When connecting the RAID battery cable, the BBU interposer card should be installed on the LSI 9265-8i card. The BBU interposer card in the figure below is just for you reference. Figure 3- 37 . Cable Routing for LSI 9265-8i Card (2U Node) I t em C a bl e F ro m ( LS I 9 2 6 5- 8i C a r d) To (R[...]

Removing and Installing System Componen ts | 209 5 Press down on th e cables, and en sure the cables are route d lower than the height of the expans ion card ass embly for the 2U node. Figure 3- 38 . Cable Routing Down (2U Node)[...]

210 | Removing and Installing System Components When securing the cable tie, make the cable tie go throug h the second air hole (from the bottom to the top) and then tighten it to encircle one of the mini-SAS cables. And mea nwhile en sure the other mini-SA S cable is held by the cable-tie clip. Figure 3- 39 . Cable T ie for 2U Node LSI 9265- 8i RA[...]

Removing and Installing System Componen ts | 211 skip to step 5; for 2 U node, continue the steps. 3 Remove the interpos er extender for 2U node . See “ Removing the Interposer Extender for 2U N ode ” on page 179 . 4 Remove the interpos er extender tray for 2U node. S ee “ Removing the Interposer Extender Tr ay ” on page 182 . 5 Disconnect [...]

212 | Removing and Installing System Components Installing the LSI 9265 -8i RAID Battery Assem bly 1 Attach the LSI92 65-8i RAID battery assembly onto th e LSI92 65-8i RAID battery tra y . See Figure 3- 40 . 2 Tighten the screw secur ing the LSI9265 -8i RAID battery ass embly. See Figure 3- 40 . 3 Connect the cable con necting to the LSI 9265 -8i c[...]

Removing and Installing System Componen ts | 213 Interposer Extender Tr ay ” on page 182 . 6 Remove the LSI 9265 -8i RAID battery assembly . See “ Removing th e LSI 9265-8 i RAID battery Assembly ” on page 210 . 7 Remove the screws s ecuring the LSI 9265 -8i RAID battery to the LSI9265 -8i RAID battery carrier. See Figure 3 - 41 . Lift the LS[...]

214 | Removing and Installing System Components 5 When replacing th e LSI 9265- 8i RAID battery for 1U node, skip to step 9; for 2U node, continue the steps. 6 Replace the interposer -extender tray. See “ Removing the Interposer Extender Tray ” on page 182 . 7 Replace the interposer exte nder for 2U node. S ee “ Removi ng the Interposer Exten[...]

Removing and Installing System Componen ts | 215 Figure 3- 44 . 2U Riser card for 2U Node 1 PCI -E Gen 3 x16 2 USB connector 3 Micro SD card socket[...]

216 | Removing and Installing System Components Removing the Riser Card f or 1U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to s[...]

Removing and Installing System Componen ts | 217 Installing the Riser ca rd for 1U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or tel ephone service and support team. Damage due [...]

218 | Removing and Installing System Components Removing the Riser car d for 2U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to s[...]

Removing and Installing System Componen ts | 219 4 Remove the two scre ws securing the 1.5U ris er card to the expansion - card bracket. See F igure 3- 47 . 5 Pull the 1.5U riser card away from the expansion- card bracket. See Figure 3- 47 . Figure 3- 47 . Removing and Installing the 1.5U Riser card 1 screw (2) 2 expansion-card bracket 3 card holde[...]

220 | Removing and Installing System Components Figure 3- 48 . Removing and Installing the 2U Riser card 1 screw (4) 2 expansion-card bracket 3 2U riser card Installing the Riser ca rd for 2U Node CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in [...]

Removing and Installing System Componen ts | 221 6 Install the expansion ca rd. See “ Installing the Expans ion Card for 2U Node ” on page 191 . 7 Replace the system- board assembly. See “ Installing a S ystem-B oard Assembly ” on page 171 . Cable Routing for Riser Ca rd (2U Node) 1 Connect the USB cable to the 2 U riser ca rd, and connect [...]

222 | Removing and Installing System Components Optional Mezzanin e Cards Removing the LSI 2 008 SAS Mezzanine Ca rd NOTE: The LSI 2008 SAS mezzanine card is seated in PCI-E Gen3 x8 mezzanine slot 3 on the system board, which is not active in 1-processor configuration . See “ C6220 II S ystem Board Connectors ” on page 325 and “ C6220 System [...]

Removing and Installing System Componen ts | 223 Figure 3- 50 . Removing and Installing the LSI 2008 SAS Mezza nine Card 1 screw (3) 2 LSI 2008 SAS mezzanine card 3 card bridge card 4 system-board assembly Installing the LSI 2008 SAS Mezzanine Card CAUTION: Many repairs may only be do ne by a certi fied service technician. Y ou should only perform [...]

224 | Removing and Installing System Components Cable Routing for LS I 2008 SAS Mezzanine Card (1U N ode) 1 Connect the mini- SAS&S GPIO cable to the LSI 2 008 SAS Mezzanine card, and connect the ot her end of the cable t o the correspondi ng connectors on the system board . See Figure 3 - 51 . 2 Connect the mini- SAS cable to the LSI 2008 S AS[...]

Removing and Installing System Componen ts | 225 3 Press down on th e cables, and en sure the cables are route d lower than the height of the C PU heat sinks. Figure 3- 52 . Cable Routing Down fo r LSI 2008 SAS Mezzanine Card (1U Node) Cable Routing for LS I 2008 SAS Mezzanine Card (2U N ode) 1 Connect the mini- SAS cable to the LSI 2008 SAS mezzan[...]

226 | Removing and Installing System Components Figure 3- 53 . Cable Routing for LSI 2008 SAS Mezzanine Card (2U Node) I te m C ab l e Fr o m ( LS I 20 0 8 S A S Me z z an i n e Ca r d) To (RAID Battery , I nt er po se r Ext end e r fo r 2U N od e , a nd S y st e m B oa r d ) Mini- SAS /SGPIO cable Mini-SA S connector 4~7 (J4) SATAII connectors 0~ [...]

Removing and Installing System Componen ts | 227 4 Press down on the c ables, and en sure the cables a re routed lower than the height of the expans ion card ass embly for the 2U node. Figure 3- 54 . Cable Routing Down for LSI 2008 SAS Mezzanine Card (2U Node )[...]

228 | Removing and Installing System Components When securing the cable tie, make the cable tie go throug h the second air hole (from the bottom to the top) and then tighte n it to encircle one of the mini-SAS cables. En sure the other mini-SA S cable is held by the cable -tie clip. Figure 3- 55 . Cable T ie for 2U Node[...]

Removing and Installing System Componen ts | 229 Removing the 1GbE M ezzanine Card NOTE: The 1GbE mezzanine card is seated in PCI-E Gen3 x8 mezzanine slot 3 on the system board, which is no t acti ve in a one-processor configuration. See “ C6220 II S ystem Board Connectors ” on page 325 and “ C6220 System Boar d Connectors ” on pag e 326 fo[...]

230 | Removing and Installing System Components 1 screw (3) 2 expansion-card bracket 3 system-board assembly 5 Remove the screws that secure the 1GbE mezzanine card ass embly . See Figure 3 - 57 . 6 Lift the 1GbE mezzanine card assembly away from the card bridge board on the sys tem board. See Figure 3- 57 . Figure 3- 57 . Removing and Installing t[...]

Removing and Installing System Componen ts | 231 7 Remove the two scre ws that secure the 1 GbE mezzanine card to the bracket. See Figure 3 - 58 . 8 Remove the 1GbE mezza nine ca rd from the bracket. See Figure 3 - 58 . Figure 3- 58 . Removing and Installing the 1GbE Mezzanine Card 1 screw (2) 2 mezzanine card bracket 3 1GbE mezzanine card Installi[...]

232 | Removing and Installing System Components the system-board a ssembly. See Figure 3- 57 . 5 Place the expansion -card bracket into the system-board assembly. See Figure 3- 56 for 1U node. See Figure 3 - 25 for 2U node. 6 Replace the screws that secur e the expansion -ca rd bracket. 7 Reconnect all the cables to t he 1GbE mezzani ne card. 8 Rep[...]

Removing and Installing System Componen ts | 233 3 Remove the screws that secur e the expans ion-ca rd bracket. See Figure 3- 59 for 1U node. See Figure 3- 25 for 2U node. 4 Lift the expansion -card bracket out of the system- board assembly. S ee Figure 3- 59 for 1U node. See Figure 3 - 25 for 2U node. Figure 3- 59 . Removing and Installing the Exp[...]

234 | Removing and Installing System Components 5 Remove the screws that secure the 10GbE mezzanine card as sembly . See Figure 3 - 60 . 6 Lift the 10GbE mezzani ne card a ssembly away from the ca rd bridge board on the sys tem board. See Figure 3- 60 . Figure 3- 60 . Removing and Installing the 10GbE mezzanine card assembly 1 screw (4) 2 10GbE mez[...]

Removing and Installing System Componen ts | 235 7 Remove the two scre ws that secure the 1 0GbE mezzani ne card to the bracket. See Figure 3 - 61 . 8 Remove the 10 GbE mezzanine card from the bracket. See Fi gure 3- 61 . Figure 3- 61 . Removing and Inst al ling the 10GbE Mezzanine Card 1 screw (2) 2 mezzanine card bracket 3 10GbE mezzanine card In[...]

236 | Removing and Installing System Components system-board assembly. See Figure 3- 60 . 5 Place the expansion -card bracket into the system-board assembly. See Figure 3- 59 for 1U node. See Figure 3 - 25 for 2U node. 6 Replace the screws that secur e the expansion -ca rd bracket. 7 Reconnect all the cables to t he 10 GbE mezzanine card. 8 Replace[...]

Removing and Installing System Componen ts | 237 Figure 3- 62 . Removing and Ins talling the Mezzanine-Card Bridge Board 1 card bridge board 2 system-board assembly Installing the Me zzanine-Card Bridge Boar d CAUTION: Many repairs may only be do ne by a certified s ervice technician. Y ou should only perform troubleshootin g and simple repairs as [...]

238 | Removing and Installing System Components System Memory Each system board has sixteen DDR3 memory m odule soc kets for the installation of up to sixteen unbuffered or registered DDR3 -1333MHz (1600MHz @2 memory modules per channel) memory modules to sup port processor 1 a nd processor 2. See “ C6 220 II System Board Connectors ” on page 3[...]

Removing and Installing System Componen ts | 239 Figure 3- 63 . DIMM Slot Locations 1 DIMM_A3 2 DIMM_A7 3 DIMM_A4 4 DIMM_A8 5 DIMM_B1 6 DIMM_B5 7 DIMM_B2 8 DIMM_B6 9 DIMM_B3 10 DIMM_B7 11 DIMM_B4 12 DIMM_B8 13 DIMM_A1 14 DIMM_A5 15 DIMM_A2 16 DIMM_A6 T able 3-2. Memo ry Module Configurations for Single Processor Memory Module Pr o c es s o r 1 CH A[...]

240 | Removing and Installing System Components T able 3-3. Memo ry Module Configurations for Dual Processors Memory Module Pr o c es s o r 1 CH A CH B CH C CH D A1 A5 A2 A6 A3 A7 A4 A8 2 √ − − − − − − − 6 √ − √ − √ − − − 8 √ − √ − √ − √ − 12 √ √ √ √ √ − √ − 16 √ √ √ √ √ √ [...]

Removing and Installing System Componen ts | 241 See “ Removing the LSI 9265 -8i RAID battery Assem bly ” on page 210 . Locate the memory modul e sockets. See Figure 3 - 64 . CAUTION: Handle eac h memory module only on either card edge, making sure not to touch the middle of the memory m odule. To avoid damaging components on the memory module,[...]

242 | Removing and Installing System Components Installing the Memo ry Modules W ARNING: The memory modules are hot to the touch for some time after the system has been powered down. Allow time f or the memory modules to cool before handling them. Handle t he memory modules by the card edges and avoid touching the components on the m emory module. [...]

Removing and Installing System Componen ts | 243 Figure 3- 65 . Installing a Memory Module 1 memory modu le 2 alignment key 3 memory module socket ejec tor (2) 4 Replace the air baffle . See “ Instal ling the Air B affle ” on page 173 . 5 Replace the system- board assembly. See “ Installing a S ystem-B oard Assembly ” on page 171 .[...]

244 | Removing and Installing System Components System Battery Replacing the System Battery W ARNING: There is a danger of a n ew battery explodi ng if it is incorrectly installed. Replace the battery only with the same or e quivalent type recommended by the manufacturer . See your s afety information for additional information. CAUTION: Many repai[...]

Removing and Installing System Componen ts | 245 Figure 3- 66 . Replacing the System Battery 1 system battery 2 positive side of battery connector 3 negative side of battery connector 7 Replace the system- board assembly. See “ Installing a System- Board Assembly ” on page 171 . 8 Enter the System Setup program to confirm that the battery is op[...]

246 | Removing and Installing System Components System Board Removing a System Board CAUTION: Many repairs may only be do ne by a certifie d service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to [...]

Removing and Installing System Componen ts | 247 Figure 3- 67 . Removing and In stalling the System Board 1 screw (8) 2 system board 3 system-board assembly[...]

248 | Removing and Installing System Components Installing a System Boa r d 1 Unpack the new system boar d. 2 Holding the system board by the edges, slide the syste m board into the system-board assembly. 3 Replace the eight screws to s ecure the system board t o the system - board assembly. 4 Transfer the processors to th e new system board. See ?[...]

Removing and Installing System Componen ts | 249 Cable Routing for Onboa rd SA T A Cables (1U N ode) 1 Connect the onboard SA TA cables to the syst em board, a nd connect the other end of the ca ble to the corresponding connectors on the system board. See F igure 3- 68 . Figure 3- 68 . Cable Routing for Onboard SA T A Cables (1U Node) I te m C ab l[...]

250 | Removing and Installing System Components 2 Press down on the c ables, and en sure the cables are route d lower than the height of the C PU heat sinks. Figure 3- 69 . Cable Routing Down for Onboard SA T A Cables (1U Node)[...]

Removing and Installing System Componen ts | 251 Cable Routing for Onboa rd SA T A Cables (2U N ode with 3.5 ” HDDs ) 1 Connect the onboard SATA ca ble to the system board , and connect the other end of the ca ble to the corresponding connectors on the other side of the syst em board . S ee Figure 3- 70 . 2 Connect the onboard SA TA cable to the [...]

252 | Removing and Installing System Components 4 Press down on th e cables, and en sure the cables are route d lower than the height of the expans ion card ass embly for the 2U node. Figure 3- 71 . Cable Routing Down for Onboard SA T A Cables (2U Node with 3.5 HDDs)[...]

Removing and Installing System Componen ts | 253 Cable Routing for Onboa rd SA T A Cables (2U N ode with 2.5 ” HDDs ) 1 Connect the onboard SATA ca ble to the system board , and connect the other end of the ca ble to the corresponding connectors on the other side of the syst em board. See Figure 3- 72 . 2 Connect the onboard SATA ca ble to the sy[...]

254 | Removing and Installing System Components I te m C ab l e Fr o m ( Sy s t em Bo a r d ) To ( In t er pos e r Ext e n d er f or 2U N od e a n d S y s te m B oa r d ) Onboard mini- SAS cable Onboard SATA output connector 0 SAS/SATA input connector 0 on th e system board Onboard SATA cable Onboard SATA connectors 4&5 SAS/SATA input connector[...]

Removing and Installing System Componen ts | 255 Note the routing of th e cable on the chass is as you remove them from the system. You mus t route these cables properly when you replace them to prevent the cables from being pinched or crimped. 5 Remove the screw that secur es the power cable cover to the pow er distribution board 1. See Figure 3 -[...]

256 | Removing and Installing System Components 7 Remove the four s crews that secure the power ca bles to the power distribution board 1 . See Figure 3 - 74 . Figure 3- 74 . Removing and Installing the Power Cables 1 screw (4) 2 power cables (4)[...]

Removing and Installing System Componen ts | 257 8 Remove the screws secur ing the power distribution board 1 to the system. See Figure 3- 75 . 9 Lift the power distribution b oard 1 out of the s ystem. See F igure 3- 75 . Figure 3- 75 . Removing and Installing the Power Distribution Board 1 1 power distribution board 1 2 screw (8)[...]

258 | Removing and Installing System Components 10 Lift the power dis tribution board connector fr om the system. See Figure 3- 76 . Figure 3- 76 . Removing and Installing the Power Distribution Board Connector 1 power distribution board connector 2 power distribution board 2 11 Disconnect all the cables from the power di stribution board 2. See Fi[...]

Removing and Installing System Componen ts | 259 14 Remove the s crews securing th e power distribution board 2 to the system. See Figure 3- 77 . 15 Lift the power dis tribution board 2 out of the system. See Figure 3 - 77 . NOTE: T o remove the power distribution board 2 that is below the power distribution board 1, remove the power distribution b[...]

26 0 | Remo ving and Installing System Components CAUTION: If removed, you must repla ce the power distribution board 2 a nd the power distribution board- connector before replacing the power distrib ution board 1. 1 If removed, first place the power distribut ion board 2 in the system. See Figure 3 - 77 . Otherwise skip to step 5. NOTE: T o instal[...]

Removing and Installing System Componen ts | 261 Cable Routing for Po w er Di stribution Board Cable routings for power di stribution board 1 (top) and power di stribution board 2 (bottom) in the 1U node system and 2U node s ystem are the same. The following figure shows an example using a 1U node system. Figure 3- 78 . Cable Routing − Power Dist[...]

262 | Removing and Installing System Components I t em C a bl e F ro m ( P ow e r Di s t ri bu ti o n B oa r d s ) To Hard-drive backplane power cable Hard-drive backplane power connector ( J84) Backplane Hard-drive backplane power cable Hard-drive backplane power connector ( J29) Backplane Power distribution board cable Control connector (J31 ) Po[...]

Removing and Installing System Componen ts | 263 Figure 3- 79 . Cable Routing − Power Distribution Board 2 (Bottom) I t em C a bl e F ro m ( P ow e r Di s t ri bu ti o n Bo a r d 2) To Ground power cables Power distribution board 1/2 Middle planes 12V power cables Power distribution board 1/2 Middle planes[...]

264 | Removing and Installing System Components Middle Planes Removing the M iddle Planes CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directed by the online or telep hone service and support team. Damage due[...]

Removing and Installing System Componen ts | 265 Figure 3- 80 . Removing and Installing the Middle-Wall Bracket 1 middle-wall bracket 2 screw (6) 7 Disconnect all the cables fro m the upper middle plane. Note the routing of th e cable on the chass is as you remove them from the system. You mus t route thes e cables properly when yo u replace them t[...]

266 | Removing and Installing System Components Figure 3- 81 . Removing and Installing the Power Cable Cov er 1 screw 2 power cable cover 10 Remove the four screws that secure the power cables to th e upper middle plane. S ee Figure 3- 82 . Figure 3- 82 . Removing and Installing the Power Cabl es 1 power cables (4) 2 screw (4)[...]

Removing and Installing System Componen ts | 267 11 Remove th e screws that secure the up per middle plane to t he middle plane holder. See Figure 3- 83 . 12 Lift the upper middle plane out. S ee Figure 3- 83 . Figure 3- 83 . Removing and Installing the Uppe r Middle Plane 1 screw (8) 2 upper middle plane[...]

268 | Removing and Installing System Components 13 Remove the s crews that secure the mi d-plane hol der support to the chassis. See Figure 3- 84 . 14 Lift the mid- plane holder sup port out of the chassis. See Figure 3- 84 . Figure 3- 84 . Removing and Installing the M id -plane Holder Support 1 screw (3) 2 mid-plane holder support[...]

Removing and Installing System Componen ts | 269 15 Remove the s crews that secure the mi d-plane hol der to the cha ssis. S ee Figure 3- 85 . 16 Lift the mid- plane holder out of the chassis. See Figure 3 - 85 . Figure 3- 85 . Removing and Installing the M id -plane Holder 1 screw (6) 2 mid-plane holder 17 Disconnect all the cables from the lower [...]

270 | Removing and Installing System Components 20 Remove the s crews that secure the l ower middle plane to the chassis . See Figure 3 - 86 . 21 Lift the lower mi ddle plane o ut of the chassis. See Fi gure 3- 86 . Figure 3- 86 . Removing and Installing the Lower Midd le Plane 1 screw (8) 2 lower middle plane Installing the M iddle Planes CAUTION:[...]

Removing and Installing System Componen ts | 271 4 Secure the screws that secure the power cables to the low er middle plane. 5 Replace the power cable co ver to the lower middl e plane. 6 Place the middle plane hold er into the chassi s. See Figure 3- 85 . 7 Replace the screws that secur e the middle plane hold er to the chass is. See Figure 3 - 8[...]

272 | Removing and Installing System Components 18 Installi ng a Cooling Fan ” on page 157 . 19 Replace the s ystem-board as semblies. See “ Installing a System- Board Assembly ” on page 171 . 20 Close the system, s ee “ Closin g the System ” on page 152 . 21 Reconnect the syst em to its electrical outlet and turn on the system, including[...]

Removing and Installing System Componen ts | 273 Cable Routing for M iddle Plane to Direc t Hard-Drive Backplan e Figure 3- 87 . Cable Routing − T op Middle Plane to Direct Backplane for 12 x3.5” Hard-Drive Configuration I t em C a bl e F ro m ( To p Mi dd le P l an e ) To ( Direct Backplane ) Hard-drive backplane cable mini-SAS connector for s[...]

274 | Removing and Installing System Components Figure 3- 88 . Cable Routing − Bottom Middle Plane to Direct Backplane for 12 x3.5” Hard-Drive Configuration I t em C a bl e F ro m ( B ot t o m Mi d d l e P l a n e) To ( Direct Backplane ) Hard-drive backplane cable mini-SAS connector for system board 1 and 2 (hard drive 1, 2, 3 and 4 ) (J 1) SA[...]

Removing and Installing System Componen ts | 275 Figure 3- 89 . Cable Routing − T op Middle Plane to Direct Backplane for 24 x2.5” Hard-Drive Configuration[...]

276 | Removing and Installing System Components I t em C a bl e F ro m ( To p Mi dd le P l an e ) To ( Direct Backplane ) Hard-drive backplane cable Mini-SA S connector for system board 1 and 2 (hard drive 1, 2, 3 and 4) (J1) SATA2 hard drive connectors 1 to 4 for system board 1 (from right to left) Hard-drive backplane cable Mini-SA S connector fo[...]

Removing and Installing System Componen ts | 277 I t em C a bl e F ro m ( B ot t o m M i d d l e P l a n e) To ( Direct Backplane ) Hard-drive backplane cable Mini-SA S connector for system board 1 and 2 (hard drive 1, 2, 3 and 4) (J1) SATA2 hard drive connectors 1 to 4 for system board 2 (fr om right to left) Hard-drive backplane cable Mini-SA S c[...]

278 | Removing and Installing System Components I t em C a bl e F ro m ( B ot t o m M i d d l e P l a n e) To ( Direct Backplane ) Hard-drive backplane cable Mini-SA S connector for system board 3 a nd 4 (hard drive 5 and 6 ) (J4) SATA2 hard drive connectors 5 to 6 for system board 4 (fr om right to left) Cable Routing for M iddle Plane to 2.5 ” [...]

Removing and Installing System Componen ts | 279 I t em C a bl e F ro m ( To p Mi dd le P l an e ) To ( Ex p a n d er C ar d) Hard-drive backplane cable Mini-SA S connector for system board 1 (J1) Mini-SA S connector ( 0~3) for system board 1 Hard- dr ive backplane cable Mini-SA S connector for system board 3 (J3) Mini-SA S connector (8~11) for sys[...]

280 | Removing and Installing System Components I t em C a bl e F ro m ( B ot t o m Mi d d l e P l a n e) To ( Ex p a n d er C ar d) Hard-drive backplane cable Mini-SA S connector for system board 1 (J1) Mini-SA S connector ( 4~7) for system board 1 Hard-drive backplane cable Mini-SA S connector for system board 3 (J3) Mini-SA S connector (12~15) f[...]

Removing and Installing System Componen ts | 281 4 Disconnect all the cables fro m the backplane. See Fi gure 3- 93 for 3.5- inch hard drives a nd Figure 3- 94 for 2.5-inch hard dri ves. Note the routing of th e cable on the chass is as you remove them from the system. You mus t route t hese cables properly wh en you replace them to prevent the cab[...]

282 | Removing and Installing System Components Figure 3- 94 . Back View of the 2.5” Di rect Backplane 1 backplane power connec tor for power supply 1 2 system fan board connector 3 SATA2 hard drive connectors 1 to 6 for system board 4 (from right to left) 4 SATA2 hard drive connectors 1 to 6 for system board 3 (from right to left) 5 SATA2 hard d[...]

Removing and Installing System Componen ts | 283 5 Disconnect front panel cable s from the power distribution board. See Figure 3- 78 . Note the routing of th e cable on the chass is as you remove them from the system. You mus t route these cables properly when you replace them to prevent the cables from being pinched or crimped. 6 Remove the screw[...]

284 | Removing and Installing System Components 7 Remove the screws tha t secure the fron t- panel assembli es to the chas sis. See Figure 3 - 96 . 8 Remove the hard -drive cage from the chassis. See Figure 3- 96 . Figure 3- 96 . Removing and Installing the Hard-Drive Cage Cable Routing for Middle Plane to Direct Backplane 1 hard-drive cage 2 front[...]

Removing and Installing System Componen ts | 285 9 Remove the screws that secur e the backplane t o the hard -dri ve cage. See Figure 3 - 97 . 10 Remove the ba ckplane from the ha rd-dri ve cage. See Figure 3 - 97 . Figure 3- 97 . Removing and Installing the Direct Backplane From the Hard-Drive Cage 1 hard-drive cage 2 3.5-inch direct backplane 3 s[...]

286 | Removing and Installing System Components 4 Replace the screws tha t secure the fron t-panel assemblies to the chassis. See Figure 3 - 96 . 5 Connect all the cables to the backplane. See Figure 3- 93 for 3.5-inch hard drives and Figure 3- 94 for 2.5- inch hard drives. You must route these c ables properly throu gh the tabs on the cha ssis to [...]

Removing and Installing System Componen ts | 287 2.5-inch Hard Driv e Expander Config uration NOTE: Following is the replacement procedure of SA T A2 a nd SAS backplane for 2 .5 -inch hard drive expander configuration . The configuration can appl y to 1 ~ 4 System-Boards and support up to 24 hard drives. For more information on the direction detail[...]

288 | Removing and Installing System Components 4 Disconnect all the cables fro m the backplane and expand er card. See Figure 3- 98 and Figure 3- 99 for 2 .5 -inch hard drives expander configuration. Note the routing of th e cable on the chass is as you remove them from the system. You mus t route these cables properly when you replace them to pre[...]

Removing and Installing System Componen ts | 289 Figure 3- 99 . T op View of the Expander Card 1 Power control connector 2 mini-SAS connector (4~7) 3 mini-SAS connector (12~15) 4 mini-SAS connector (8~11) 5 mini-SAS connector (0~3) 5 Disconnect front panel cables from the power distribution board . See Figure 3-1 08. Note the routing of th e cable [...]

290 | Removing and Installing System Components 6 Remove the screws that secur e the hard -drive cage t o the chassis. See Figure 3-1 00. 1 hard-drive cage 2 screw (2) Figure 3- 100 . Removing and Installing the 2.5” Ha rd -Drive Backplane for Expander Configuration[...]

Removing and Installing System Componen ts | 291 7 Remove the screws tha t secure the fron t- panel assemblies to the chassis. See Figure 3 - 101 . 8 Remove the hard -drive cage from the chassis . See Figure 3- 101 . Figure 3- 101 Removing and Installing the 2.5” Har d -Drive Cage for Expander Configuration 1 hard-drive cage 2 front-panel assembl[...]

292 | Removing and Installing System Components 9 Remove the screws that s ecure the expander card assembly to the hard- drive cage. See F igure 3- 102 . Figure 3- 102 . Removing and Installing the screws securing the expander card assembly to the hard-drive cage 1 hard-drive cage 2 screw ( 6)[...]

Removing and Installing System Componen ts | 293 10 Remove th e expander card a ssembly from the ha rd-drive c age. See Figure 3-1 03. Figure 3- 103 . Removing and Installing the 2.5” Hard-Drive Expander Card Assembly from the Hard-Drive Cage 1 hard-drive cage 2 expander card assembly[...]

294 | Removing and Installing System Components 11 Remove the s crews that secure the back plane for expander configuration to th e hard-drive cage. See Figure 3 - 104 . 12 Remove th e backplane for ex pander configuration from th e hard-dr ive cage . See Figure 3 -104. Figure 3- 104 . Removing and Installing the Backplane for Expander C onfigurati[...]

Removing and Installing System Componen ts | 295 Installing the 2.5-inch Ha r d Drive Backp lane for Expan der Configuration CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in y ou r product documentation, or as directe d by the online or telephone[...]

296 | Removing and Installing System Components 12 Reconnect the syst em to its electri cal outlet and turn on the system, including any attached p eripherals. Front Panels Removing the Fro nt Panel CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform tro ubleshooting and simple repairs as authorized i[...]

Removing and Installing System Componen ts | 297 9 Remove the screws that secur e the front -panel ass embly to the hard - drive cage. See F igure 3- 105 . 10 Remove the f ront-panel as sembly from the hard-drive cag e. See Figure 3-105. Figure 3- 105 . Removing and Installing a Front Panel Asse mbly 1 front-panel assembly 2 screw (2)[...]

298 | Removing and Installing System Components 11 Push asi de the retention hooks on the front - panel assembly. See Figure 3-106. 12 Remove the f ront panel from the front -panel a ssembly. See Figure 3- 106 Figure 3- 106 . Removing and Installing a Front Panel 1 front-panel assembly 2 front pan el 3 retention hooks Installing the Front Pane l CA[...]

Removing and Installing System Componen ts | 299 3 Replace the screws that secur e the front -panel ass embly to the hard - drive cage. See F igure 3- 105 . 4 Replace the hard- drive cage into the chas sis. See Figure 3 - 96 . 5 Replace the screws tha t secure the fron t-panel assemblies to the chassis. See Figure 3 - 96 . 6 Replace the screws that[...]

300 | Removing and Installing System Components Sensor Boards Removing the Senso r Board for 3.5” H ard-D rive System CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubl eshooting and simple repairs as a uthorized in your product documentation, or as directe d by the online or telephone servi[...]

Removing and Installing System Componen ts | 301 8 Remove the screw that secur es the sensor board to the hard drive cage. See Figure 3 - 107 . 9 Remove the sensor board from the hard dri ve cage. See Figure 3- 107 . Figure 3- 107 . Removing and Installing the Sensor Board 1 sensor board 2 screw Installing the Senso r Board for 3.5” H ard-Drive S[...]

302 | Removing and Installing System Components 6 Connect all the cables to the backplane. See Figure 3- 93 for 3.5-inch hard drives. You must route these c ables properly on th e chassis to prevent them from being pinched or cr imped. 7 Connect front panel cabl es to the power di stribution boar d. See Figure 3-108 or F igure 3- 111 . You must rou[...]

Removing and Installing System Componen ts | 303 Figure 3- 108 . Cable Routing − Sensor Board and Front Panel I t em C a bl e F ro m ( P ow e r Di s t ri bu ti o n Bo a r d ) To ( Se n s or B o ar d an d F r on t P an e ls ) Sensor board cable Sensor board power connector (J1) Sensor Board Front panel cable Front panel connector (J 16 ) Front Pan[...]

304 | Removing and Installing System Components Removing the Senso r Board for 2. 5” H ard-D rive System CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support[...]

Removing and Installing System Componen ts | 305 8 Remove the screw that secur es the sensor boar d as sembly to the hard drive cage. See F igure 3- 109 . 9 Remove the sensor board assembly from the hard drive cage. See Figure 3-1 09. Figure 3- 109 . Removing and Installing the Sensor Board Asse mbly 1 sensor board assembly 2 screw (2)[...]

306 | Removing and Installing System Components 10 Remove the s crew that secures the s ensor board to the sen sor -board holder. See Fi gure 3- 110 . 11 Remove the s ensor board fro m the sensor- board holder. S ee Figure 3 - 110 . Figure 3- 110 . Removing and Installing the Sensor Board 1 screw 2 sensor board 3 sensor-board holder Installing the [...]

Removing and Installing System Componen ts | 307 3 Replace the screw that secure s the sensor board to the hard drive cage. See Figure 3 - 109 . 4 Connect the sensor board ca ble to the sens or board. See Figure 3- 111 . 5 Replace the hard drive cage i nto the chassis . See Figure 3 - 96 . 6 Re place the screws that secur e the hard -drive cage t o[...]

308 | Removing and Installing System Components Figure 3- 111 . Cable Routing − Sensor Board and Front Panel I t em C a bl e F ro m ( P ow e r Di s t ri bu ti o n Bo a r d ) To ( Se ns or B o ar d a n d F r on t P an e ls ) Sensor board cable Sensor board power connector (J1) Sensor Board Front panel cable Front panel connector (J16) Front Panel [...]

4 T roubleshooting Y our System | 309 T r oubleshooting Y our System Minimum Configuration to P OST  One Power Supply  One Processor (CPU) i n socket CPU1 (minimum for trou bleshooting)  One Memory Module (DIM M) ins talled in the socket A1 NOTE: T he three items above are the minimu m configuration to POST . When the PCI -E slot 1 and slo[...]

310 | T roubleshooting Y our System Installation Problems Perform the following chec ks when you trou bleshoot installation problems:  Check all cable and po wer connections (incl uding all rack cable connections).  Unplug the power cord and wait for one minute. Th en reconnect the power cord and try agai n.  If the network is reportin g a[...]

T roubleshooting Y our System | 311 T roubleshooting the Video Subsystem 1 Check the system and power connections to the monitor. 2 Check the video interfa ce cabling from the system to the monitor. T roubleshooting a USB D evice Use the following ste ps to troubleshoot a USB ke yboard and/or mouse. For other USB devices, go to step 5. 1 Disconnect[...]

312 | T roubleshooting Y our System If the problem persists, repla ce the device. If all troubleshooting fai ls, see “ Getting H elp ” on page 343 . T roubleshooting a Serial I/O D evice 1 Turn off the system and a ny peripheral de vices connected to the serial port. 2 Swap the serial interface cable with another working ca ble, and turn on the[...]

T roubleshooting Y our System | 313 3 Ensure that the appropria te drivers are ins talled and the protocols are bound. See the NIC ’ s documentation. 4 Enter the System Setup program and confi rm that the NIC ports are enabled. See “ Usi ng the System Setup Program ” on page 68 . 5 Ensure that the NICs, hubs, and switches on the network are a[...]

314 | T roubleshooting Y our System 5 Reinstall the components you removed in step 3. 6 Close the system. See “ Clos ing the System ” on page 152 . 7 Reconnect the system to the electrical outlet, and turn on the system and attached peripheral s. If the system does no t start properly, see “ Getting Help ” on page 343 . 8 If the system star[...]

T roubleshooting Y our System | 315 T roubleshooting the System B attery 1 Re -enter the time and dat e through the System Setup pr ogram. See “ Sy stem Setup Options at Boot <F2> Initiate Setup during POST <F 8> Load customized defaults <F9> Load optimal defaults in Setup menu. <F10> Save Settings and exi t in BIOS Setup [...]

316 | T roubleshooting Y our System NOTE: Some software may cause the system time to speed up or slow down. If the system seems to operate normally excep t for the time kept in the System Setup program, the problem may be caused by software rather than by a defective battery . T roubleshooting Power Supplies 1 Identify the faulty power s upply by t[...]

T roubleshooting Y our System | 317  Ambient temperature is too high.  External airflow is obstructed.  Cables inside the system o bstruct airflow.  An individual cooli ng fan is removed or has failed. S ee “ T roubleshooting a Fan ” on page 317 . T roubleshooting a Fan 1 Locate the faulty fan indi cated by the diagnos tic software.[...]

318 | T roubleshooting Y our System T roubleshooting System Memory CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troublesho oting and simpl e repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cing that is[...]

T roubleshooting Y our System | 319 8 Reconnect the system to its e lectrical outlet, and turn on t he system and attached peripheral s. 9 Enter the System Setup program and check the system m emory settings. See “ M ain Screen ” on page 76 . If the problem is not res olved, proceed with the next ste p. 10 Turn off the s ystem and attached peri[...]

320 | T roubleshooting Y our System T roubleshooting a Hard Driv e CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cing that is [...]

T roubleshooting Y our System | 321 T roubleshooting a Storage C ontroller NOTE: When troubleshooting a SAS RAID controller, also see the documentation for your operating system and the con troller. 1 Enter the System Se tup program and ensure that the SAS controller is enabled. See “ Usi ng the System Setup Program ” on page 68 . 2 Restart the[...]

322 | T roubleshooting Y our System 9 Install the system- board assembly. See “ I nstalling a System -Board Assembly ” on page 171 . 10 Reconnect the syst em to its electrical outlet, and turn on the system and attached peripheral s. If the problem persists, s ee “ Getting Help ” on page 343 . T roubleshooting Expansion Cards NOTE: When tro[...]

T roubleshooting Y our System | 323 T roubleshooting Processors CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the onlin e or telephone service and support team. Damage due to servi cing that is no[...]

324 | T roubleshooting Y our System 12 Remove the s ystem-board a ssembly. See “ Removing a System- Board Assembly ” on page 170 . 13 Replace process or 1 with pro cessor 2. See “ Installing a Processor ” on page 178 . 14 Repeat step 9 thr ough step 11. If you have tested both th e processors a nd the problem persists, the system board is f[...]

5 Jumpers and Connec tors | 325 Jumpers and Connectors This chapter pro vides specific information about the system jumpers. It also provides some basi c information on jumpers a nd switches a nd describes the connectors on the various boards in the system. C6220 II System Bo ard Connectors Figure 5-1. C6220 II System Board Connectors NOTE: T he in[...]

326 | Jumpe rs and Connectors 17 processor 2 18 DIMM slots for processor 2 19 processor 1 20 DIMM slots for processor 1 21 PWRD_EN jumper 22 PCI -E Gen3 x16 slo t 2 23 PCI -E Gen3 x16 slo t 1 24 NCSI CN connector 25 power button/power&system LE D 26 VGA port 27 serial port 28 management port 29 LAN connector 2 30 LAN connector 1 31 ID LED 32 du[...]

Jumpers and Connectors | 327 17 PCI -E x16 slot 4 18 processor 2 19 DIMM slots for processor 2 20 processor 1 21 DIMM slots for processor 1 22 BIOS recovery jumper 23 PWRD_EN jumper 24 ME firmware recovery jumper 25 MEDBG1 jumper 26 LAN LED connector 27 PCI - E Gen2 x16 slot 1 28 SGPIO connector 1 29 PCI - E Gen2 x16 slot 2 30 power button pass jum[...]

328 | Jumpe rs and Connectors Backplane Connectors 3.5" Hard-Drive Direc t Backplane Figure 5-3. Front View o f the Backplane 1 3.5” backplane 2 hard drive connectors 1, 2 and 3 for sy stem board 1 (from top to bottom) 3 hard drive connectors 1, 2 and 3 for system board 2 (from top to bottom) 4 hard drive connectors 1, 2 and 3 for system boa[...]

Jumpers and Connectors | 329 Figure 5-4 . Back V iew of the Backplane 1 backplane power connec tor for power supply 1 2 1x8pin fan controller board connector 3 SGPIO connector 4 for system board 4 4 SGPIO connector 3 for system board 3 5 SGPIO connector 2 for system board 2 6 SGPIO connector 1 for system board 1 7 backplane jumper 8 SATA2 and SAS c[...]

330 | Jumpe rs and Connectors 2.5" Hard-Drive Direc t Backplane Figure 5-5. Front View o f the Backplane 1 hard drive connectors 1 to 6 for system board 1 (from left to right) 2 hard drive connectors 1 to 6 for system board 2 (from left to right) 3 hard drive connectors 1 to 6 for system board 3 (from left to right) 4 hard drive connectors 1 t[...]

Jumpers and Connectors | 331 Figure 5-6. Back View of the Backplane 1 backplane power connec tor for power supply 1 2 system fan board connector 3 SATA2 and SAS connectors 1 to 6 for system board 4 (from right to left) 4 SATA2 and SAS connectors 1 to 6 for system board 3 (from right to left) 5 SATA2 and SAS connectors 1 to 6 for system board 2 (fro[...]

332 | Jumpe rs and Connectors 2.5" Hard-Drive Expa nder Backplane Figure 5-7. Front View of the Backplane 1 hard drive connectors 1 to 24 (from left to right) 2 2.5” backplane for expander configuration Figure 5-8. Back View of the Backplane 1 backplane power connec tor for power supply 1 2 expander-card connector 1 3 expander-card connector[...]

Jumpers and Connectors | 333 Figure 3-9 . T op Vie w of the 2.5” Hard -Drive Expander Card 1 power control connector 2 mini-SAS connector (4~7) 3 mini-SAS connector (12~15) 4 mini-SAS connector (8~11) 5 mini-SAS connector (0~3) Middle Plane Connectors Figure 5- 10 . Middle Plane Connectors 1 2x17pin control connector for power distribution board [...]

334 | Jumpe rs and Connectors Interposer Extender for 2U Node Con nectors Figure 5- 11 . Interpose r Extender for 2U node Connectors 1 SATA2 and SAS connectors connector 6 2 SATA2 and SAS connectors connector 7 3 2x9pin power connector 4 SATA2 and SAS connectors connector 5 5 SATA2 and SAS connectors 4 6 SATA2 and SAS connectors connector 3 7 SATA2[...]

Jumpers and Connectors | 335 LSI 2008 SAS Mezzanin e Card Connectors Figure 5- 12 . LSI 2008 SAS Mezzanine Card Connectors 1 mezzanine card connector 2 LSI 2008 mezzanine card 3 mini-SAS connector (port 4- 7) 4 mini-SAS connector (port 0- 3)[...]

336 | Jumpe rs and Connectors 1GbE Mezzanine Card Connectors Figure 5- 13 . 1GbE Mezzanine Card Connectors 1 1GbE mezzanine card 2 mezzanine card connector 3 NIC connector 4 4 NIC connector 3 5 NIC connector 2 6 NIC connector 1[...]

Jumpers and Connectors | 337 10GbE Mezzanine Card Connectors Figure 5- 14 . 10GbE Mezzanine Card Connec tors 1 SFP + port 0 2 10GbE mezzanine card 3 mezzanine card connector 4 SFP + port 1[...]

338 | Jumpe rs and Connectors Power Distribution Board 1 C onnectors Figure 5- 15 . Power Distribution Board 1 Connectors 1 front panel connector for system board 1 and 2 2 system fan connector 3 hard drive backplane powe r connector 1 4 hard drive backplane powe r connector 2 5 1x10pin control connector 6 2x17pin control connector for system board[...]

Jumpers and Connectors | 339 Power Distribution Board 2 Connectors Figure 5- 16 . Power Distribution Board 2 Connectors 1 bridge card connector 2 1x10pin control connector Sensor Board Connectors Figure 5- 17 . Sensor Board Connectors 1 power connector 2 sensor board[...]

340 | Jumpe rs and Connectors Jumper Settings CAUTION: Many repairs may only be do ne by a certified service technician. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone serv ice and support team. Damage due to servi cing that is not authorized by De[...]

Jumpers and Connectors | 341 System Configura tion Jumper Set tings on the C6220 System Board The function of system co nfiguration jumper installed on each C6220 system board is s hown below: Figure 5- 19 . System Configuration Jumpers on the C6220 System Board T able 5-2. System Config uration Jumper on the C6220 System Boa rd Ju m p er Fu n ct i[...]

342 | Jumpe rs and Connectors Direct Backplane Jumpe r Settings CAUTION: Many repairs may only be do ne by a certified service techni cian. Y ou should only perform troubleshootin g and simple repairs as authorized in your product documentation, or as directe d by the online or telephone service and support team. Damage due to servi cing that is no[...]

6 Getting Help | 343 Getting Help Contacting Dell For customers in the United States, call 800 - WWW -DELL (800- 999 -3355). NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice , packing slip, bill, or Dell product catalog. Dell provides several online and telephone -based suppor t and s[...]

7 344 | Index Index A about your system, 1 3 adapter bracket Installing a 2 .5-inch SSD into a 2.5-inch a dapter bracket, 163 B back panel features , 24 backplane installing direct BP , 285 removing 2.5-inch ha rd drive backplane for expander configuration, 287 removing direct BP , 28 0 backplane installing 2 .5-inch hard drive backplane for expand[...]

Index | 345 Dell contacting, 343 drive blank installing, 158, 159 re moving, 158 , 159 E expansion card troubleshooting, 322 expansion card for 1U node installing, 186 removing, 184 expansion card for 2U node installing, 191 removing, 187 F features and indica tors front panel, 14 fresh air support, 52, 6 2 front panel features, 14 front panel inst[...]

346 | Index 198 LSI 9265-8 i card for 2U node, 206 memory modules, 2 42 mezzanine card (10GbE), 2 35 mezzanine card (1GbE), 23 1 middle planes, 27 0 power distribution board, 259 power supply , 167 processor , 178 riser card for 1U node, 217 riser card for 2U node, 220 SAS Mezzanine ca rd, 223 sensor board, 301 system board, 248 system board assemb[...]

Index | 347 N NICs troubleshooting, 312 P phone numbers, 3 43 POST accessing system fea tures, 13 power distribution board installing, 259 removing, 254 power supplies installing, 167 removing, 166 processor installing, 178 removing, 176 processors troubleshooting, 323 R R AID card LSI 9210-8 i HBA, 194 LSI 9265-8 i with BBU, 194 LSI 9285-8 e with [...]

348 | Index riser card for 2U node installing, 220 removing, 218 S safety , 150 SAS controller da ughter card troubleshooting, 321 SAS Mezzanine ca rd installing, 223 removing, 222 SAS RAID controller daughter card troubleshooting, 321 SSD Installing a 2 .5-inch SSD into a 3.5-inch Hard- Drive Carrier , 163 startup accessing system fea tures, 13 su[...]

Index | 349 V video troubleshooting, 311 W warranty, 52 wet system troubleshooting, 313[...]