Dodge 2004 DR Ram SRT-10 manuel d'utilisation

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 6 1 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ...................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 5 䡵 V an Conversions/Campers ................. 5 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations ........... 7 1[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. V AN CONVER[...]

VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible fr om outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label af fixed to a window on your vehicle. Save this label fo[...]

VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 7 1[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 1 ▫ Key-In-Ignition Reminder ................ 1 1 ▫ Sentry Key — If Equipped ................ 1 1 䡵 Ignition And Steering Lock — If Equipped ...... 1 4 ▫ Manual T ransmissions ................... 1 4 䡵 Door Key ....................[...]

▫ T o Disarm The System ................... 2 5 䡵 W indows ............................. 2 6 ▫ Power W indows — If Equipped ............. 2 6 ▫ Sliding Rear W indow ................... 2 7 ▫ W ind Buffeting ........................ 2 7 䡵 Occupant Restraints ...................... 2 7 ▫ Lap/Shoulder Belts ..................... 2 8 ?[...]

A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith. If you r eceived your keys without the bag, ask your dealer to giv[...]

The ⬙ Security Light ⬙ , located in the instrument cluster , will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not r eceive a valid signal from the ignition key , the ⬙ Security Light ⬙ will flash continuously to signal that the vehicle has been immobilized. If the[...]

Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. T urn the ignition back to the OFF position and remove the first key . 2. Insert the second[...]

IGNITION AND STEERING LOCK — IF EQUIPPED Manual T ransmissions Depress and hold the r elease button located between the ignition switch and the instrument panel. T urn the igni- tion key to LOCK and remove the key . DOOR KEY The same key used to start the vehicle is also used to unlock the doors. T o unlock the vehicle doors, insert the key into [...]

W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death. NOTE: V ehicles equipped with remote keyless entry do not have a passeng[...]

As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver ’ s door is open while the key is in the ignition. Central Locking — If Equipped V ehicles with security will have a feature called ⬙ Central Locking ⬙ . When the key is placed in the door cylinder and turned to the ?[...]

2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming pr ocedure). 3. Place the key into the ignition. 4. W ithin 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. W ithin 30 seconds, press the drive[...]

T o unlock the doors: Press and r elease the UNLOCK button on the key fob once to unlock only the driver ’ s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programme[...]

T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped fr om the assembly plants activated. If desired this featur e can be disabled by using the followi[...]

2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedur e). 3. Place the key into the ignition. 4. T urn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the LOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the LOCK butt[...]

Programming Additional T ransmitters V ehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of four fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle thr ough the use of a cur- rently pr ogrammed fob. NOTE: When[...]

1 1. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 1 1 for a total of 4 fobs. 13. T urn the ignition to the OFF position or wait 60 seconds to exit program mode. 14. Y our vehicle will remain in pr ogram mode for up to 60 seconds from when the original chime (i.e. Step #7) was heard. After[...]

T ransmitter Battery Service The recommended r eplacement battery is a 3V lithium 2016 cell. This transmitter requir es two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit boar d. 1. W ith transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart.[...]

SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly . For an addi- tional 15 minutes only the h[...]

T o Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver ’ s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will als[...]

WINDOWS Power Windows — If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessor[...]

Auto Down (Driver ’ s Side Only) The driver ’ s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . Sliding Rear Window A locking device in the center of the window helps to prevent entry fr om the rear of the vehicle. Squeeze the lock to release the window . WIN[...]

W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly . Buckle up even though you are an excellent driver [...]

W ARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a[...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to[...]

W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the poss[...]

W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won ’ t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can ’ t do its job as well. In a collision it could even cut into you. Be sure [...]

Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the vehicle ignition key into the c[...]

W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing i[...]

W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located [...]

As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you ’ ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically pre- loc[...]

NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the airbag contr ol module. Like the airbags, the pretensioners ar e single use items. After a collision that is severe enough to deploy the airbags and prete[...]

3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver ’ s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled. 4. T urn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced W arning System (BeltAlert) can be reacti[...]

W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver And Right Front Passenger Supplemental Restraint Syste[...]

W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not mount any aftermarket equipment[...]

• Infants in rear facing child r estraints must NEVER ride in the front seat of a vehicle with a passenger fr ont airbag unless the airbag is turned off (Standar d Cab V ehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section. • If your vehicle does not h[...]

Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Crash Sensor • Interconnecting W iring • Knee Impact Bolsters • Passenger Side Frontal Airbag ON/OFF Switch (Stan- dard Cab V e[...]

How The Airbag System W orks • The airbag control module determines if a fr ontal collision is severe enough to r equire the airbags to inflate. • The airbag control module will not detect r oll over , or rear collisions. • The airbag control module also monitors the r eadiness of the electronic parts of the system whenever the ignition switc[...]

• When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes yo[...]

• is a child, age 1 to 12 who must ride in the front seat because there is no r ear seat, because there is no r ear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, • has a medical condition which makes passenger airbag inflation (deployment) a greater ris[...]

If A Deployment Occurs The airbag system is designed to deploy when the air bag control module detects a moderate-to-sever e frontal col- lision, and then immediately to deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. I[...]

W ARNING! Deployed airbags can ’ t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. W indow Airbags Supplemental Restraint System (SRS) — If Equipped The window airbag control module determines if a side collision is severe enough to r equire the side airbags to inflate. The window airba[...]

Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically . In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off. Maintaining Y ou[...]

Airbag Light Y ou will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: • The airbag light does not come on or flickers during the 6 to 8 seconds when the ignition switch is [...]

W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper re[...]

• Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forwar d-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing dir ection are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year . These child seats are also held in the vehicle by[...]

Here are some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it befor e you buy it. • The restrain[...]

• If the belt still can ’ t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can ’ t make the child restraint secur e, try a differ ent seating position. • Buckle the child into the sea[...]

The LA TCH lower anchorage bars are located wher e the seatback meets the seat cushion. If the lower anchorage bars are not visible, identification dots ar e located above the standard cab fr ont seat lower anchorages as a guide for locating the lower anchors. NOTE: For children riding in the fr ont seat of a Stan- dard Cab model r efer to the “ [...]

Installing the Child Restraint System W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint. Many , but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler [...]

W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top[...]

Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be lo[...]

• W ait until the engine has reached normal operating temperature befor e driving at the recommended maxi- mum break-in speed. • A void excessive idling. • Check the engine oil level at every fuel fill. NOTE: A new engine will consume some oil during the first few thousand miles of operation. This should be considered as a normal part of the [...]

Exhaust Gas W ARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. T o avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If i[...]

Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.) o[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 6 5 ▫ Automatic Dimming Mirror — If Equipped .... 6 5 ▫ Outside Mirrors ....................... 6 5 ▫ Exterior Mirrors Folding Featur e ........... 6 6 ▫ Electronic Power Mirr ors — If Equipped ...... 6 6 ▫ Electric Rear W indow Defroster[...]

䡵 T o Open And Close The Hood .............. 8 4 䡵 Lights ................................ 8 6 ▫ Interior Lights ........................ 8 6 ▫ Battery Saver ......................... 8 7 ▫ Headlamp Delay — If Equipped ........... 8 8 ▫ Headlights, Parking Lights, Panel Lights ...... 8 8 ▫ Daytime Running Lights (Canada And Fleet V [...]

▫ T o Accelerate For Passing ................ 9 8 䡵 Overhead Console ....................... 9 9 ▫ Courtesy/Reading Lights ................. 9 9 䡵 Compass/T emperature Mini-T rip Computer .... 1 0 0 ▫ US/M Button ........................ 1 0 0 ▫ Reset Button ......................... 1 0 1 ▫ Global Reset ......................... 1 0 [...]

䡵 Cupholders ........................... 1 1 4 ▫ Front Cupholders ..................... 1 1 4 䡵 Storage .............................. 1 1 4 ▫ Center Storage Compartment ............. 1 1 4 ▫ Storage And Seats ..................... 1 1 5 䡵 Pickup Box ........................... 1 1 6 䡵 Slide-In Campers ....................... 1 1 8 ?[...]

MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during c[...]

W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mir[...]

Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move. Electric[...]

UConnect ™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system ’ s micro- phone for private conversations. The UConnect ™ ; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth ™ Hands-F[...]

The UConnect ™ system is fully integrated into your vehicle, including your vehicle ’ s stereo system. All voice prompts as well as the other party ’ s voice in a conversa- tion will be played over your vehicle ’ s stereo system. The volume of the UConnect ™ system can be controlled through your normal ster eo controls. The radio display [...]

enter into your cellular phone during the cellular phone pairing process. Y ou can enter any four-digit pin number . Y ou will not need to remember this pin number after the initial registration pr ocess. • The UConnect ™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular pho[...]

• After the ⬙ Ready ⬙ prompt, say ⬙ Dial ⬙ or ⬙ Call ⬙ followed by the name and designation of a phonebook entry that you wish to dial. For example, you can say ⬙ Call John Doe W ork ⬙ . Add Names to Y our UConnect ™ Phonebook • Press the “ Phone ” button to begin. • After the ⬙ Ready ⬙ prompt, say ⬙ Phonebook New [...]

After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mob[...]

List All Names in the UConnect ™ Phonebook • Press the ’ Phone ’ button to begin. • After the ⬙ Ready ⬙ prompt, say ⬙ Phonebook List Names ⬙ . • The UConnect ™ system will play the names of all the phonebook entries. • T o call one of the names in the list, press the ’ V oice Recognition ’ button during the playing of th[...]

Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, press the ’ Phone ’ button to place the current call on hold and answer the incoming call. T o reject the incoming call, you can disr egard the call and continue with your current conversation. Making a Second C[...]

Three-W ay Calling T o initiate three-way calling, pr ess the ’ V oice Recogni- tion ’ button while a call is in progr ess and make a second phone call. When the second call is established, press the ’ Phone ’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call T ermination T o e[...]

• Y ou will be asked to say the name of the phone that you wish to delete. Y ou can either say the name of the phone that you wish to delete or you can say ⬙ All ⬙ to delete all the phones. Connect or Disconnect the Connection between the UConnect ™ System and Y our Cellular Phone Y our cellular phone can be paired with many dif ferent elec[...]

• The lower priority phone will only be used for the next phone call. After that, the UConnect ™ system will return to using the highest priority phone in the vehicle. UConnect ™ System Features Barge In - T ouch T one Phone Inputs Y ou can use your UConnect ™ system to access a voice mail system, an automated service, or any other phone nu[...]

T urning Confirmation Prompts On/Off T urning confirmation prompts of f will stop the system from confirming your choices (e.g. the UConnect ™ sys- tem will not repeat a phone number befor e you dial it). • Press the ’ Phone ’ button to begin. • After the ⬙ Ready ⬙ prompt, say ⬙ Setup Confirmation ⬙ . The UConnect ™ system will [...]

Help If you need assistance at any prompt or if you want to know what your options are at any pr ompt, say ⬙ Help ⬙ . The UConnect ™ system will play all the options at any prompt if you ask for help. Cancel At any prompt, you can say ⬙ Cancel ⬙ and you will be returned to the pr evious menu. Emergency Assistance If you are in an emer gen[...]

W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. W ARNING! Y ou can be seriously , even fatally injured riding in a seat with the seatback recli[...]

Up, Down, Forward, and Rearward UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 81 3[...]

The power seat controls ar e on the outboard side of the front seat cushions. Thr ee switches control the seat move- ment. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable posi- tion. The same switch can be moved up and down to control seat height. Change the seat angle by using the two toggle switche[...]

Manual Seatback Recline The recliner mechanism contr ol is on the outboard side of the seat. T o recline, lean forwar d slightly , lift the lever , then push back to the desired position and r elease the lever . Lean forward and lift the lever to r eturn the seatback to its normal position. Using body pressur e, lean forward and r earward on the se[...]

Adjustable Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears. T o lower the head restraint, push in the button and then push down on the head restraint. TO OPEN AND CL[...]

T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the fr ont center of the hood to ensure that both latches engage. W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. UNDERST ANDING T[...]

LIGHTS Interior Lights Courtesy/ dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob. Rotating the dimmer control to the optional fully upwar d position w[...]

turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer contr ol all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙ Party ⬙ mode because it allows the doors to stay open for extended periods of time without dischargi[...]

Headlamp Delay — If Equipped T o aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will [...]

T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Daytime Running Lights (Canada and Fleet V ehicles[...]

CARGO LIGHT The cargo lights ar e turned on by rotating the dimmer control to the optional fully upwar d position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature. MUL TIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering colu[...]

Passing Light Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headligh[...]

Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed. Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desira[...]

The delay interval decreases as you r otate the knob until it enters the LO continual speed position. The delay can be regulated fr om a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less. W ARNING! Sudden loss of visibility through the[...]

TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehi[...]

DRIVER ADJUST ABLE PEDALS The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seat[...]

CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal ’ s path. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator opera- tion at speeds greater[...]

T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, clutch pressur e while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed cont[...]

T o decrease speed while the speed contr ol is on, press and hold the COAST button. Release the button when the desired speed is r eached, and the new speed will be set. T o Accelerate For Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. NOTE: When driving uphill, at elev[...]

OVERHEAD CONSOLE The overhead console consists of the following featur es: • Courtesy/Reading Lights • Compass/T emperature Mini-T rip Computer (CMTC) • Universal Garage Door Opener Courtesy/Reading Lights In the middle of the console are two courtesy/r eading lights. Both lights illuminate as courtesy lights when a door is opened, when the d[...]

COMP ASS/TEMPERA TURE MINI-TRIP COMPUTER This overhead console consists of the following: • Courtesy Lights • Compass/T emperature Mini-T rip Computer • Universal Garage Door Opener This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored. US/M Button Use this button to[...]

RESET Button Use this button to reset the following displays to zer o: A verage Fuel Economy T rip Odometer Elapsed time Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to choose or cycle through the four trip condit[...]

A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset incr eases. It is suggested that this mode be reset periodically for general operation or when driving conditions change[...]

Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. W ARNING! Even if the display still reads a few degrees above 32 ° F(0 ° C), the road [...]

Manual Compass Calibration NOTE: T o ensure pr oper compass calibration, make sure the compass variance is pr operly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear , you must manually put the compass into the “ Calibration ” mode. T o Put Into a Calibration Mode T urn on the igni[...]

T o set the variance: T urn the ignition ON and set the display to “ Compass/T emperature. ” Pr ess the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside T emperature Because the ambient te[...]

GARAGE DOOR OPENER The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal T ransceiver operates off your vehicle ’ s battery and charging system; n[...]

Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. Some vehicles may requir e the ignition switch to be turned to the second (or ⬙ accessories ⬙ ) position for programming and/or opera- tion of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of [...]

W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inch[...]

If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ⴖ Program- ming ⴖ steps 6-8 to complete the programming of a r olling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙ learn ⬙ or ⬙ smart ⬙ [...]

If you live in Canada or you are having dif ficulties programming a gate operator by using the ⬙ Pr ogram- ming ⬙ procedur es (regardless of wher e you live), replace ⴖ Programming HomeLink ⴖ step 3 with the following: NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the ⬙ cycling ⬙ [...]

Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink button, proceed with ⬙ Programming ⬙ step 2[...]

ELECTRICAL POWER OUTLETS The auxiliary electrical outlets can provide power for in cab accessories designed for use with the standard “ cigar lighter ” plugs. One of the outlets is the cigar lighter outlet, located in the instrument panel below the ash r eceiver . This outlet has a fused direct feed fr om the battery so it receives power whethe[...]

CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the r eceiver and then allowing the receiver to open. The cigar lighter is located in the instrument panel below the ash receiver . NOTE: This outlet has a fused direct feed fr om the battery so it receives power whether the ignition is ON or OFF[...]

CUPHOLDERS Front Cupholders The cupholders consist of two cupwells for passenger convenience. STORAGE Center Storage Compartment The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armr est to raise the cover . Inside there is a power outlet (if equipped[...]

configure the storage ar ea into compartments. For ex- ample, compartments can be configured to hold a lap-top computer , a cellular telephone, CD ’ s and miscellaneous items. The top of the cover provides a gener ous firm surface to serve as a desktop for your “ mobile office. ” W ARNING! • This armrest is not a seat. Anyone seated on the [...]

There is also storage behind the seat. This storage ar ea contains the 10 inch subwoofer (if equipped). PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar 威 toolbox brackets available from you dealer . 1 16 UNDE[...]

Y ou can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor . Place lumber across the box in the indentations pr ovided above the wheel housings and in the bulkhead dividers to form the floor . W ARNING! The pickup box is intended for load carrying pur- poses only , not for passengers, who should sit in seats [...]

There ar e stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards acr oss the box from side to side to create separate load compartments in the pickup box. There ar e four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (45[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 119 3[...]

[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Contr ols ................. 1 2 2 䡵 Instrument Cluster ...................... 1 2 3 䡵 Instrument Cluster Description ............. 1 2 4 䡵 Electronic Digital Clock .................. 1 3 1 ▫ Clock Setting Procedur e................. 1 3 1 䡵 Sales Code RBQ — AM/FM Stereo [...]

INSTRUMENTS AND CONTROLS 122 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 123 4[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle[...]

2. V oltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. T ypically this would be between 12 and 14 volts. If the pointer moves to either extreme left or right and r emains there during normal driving, the electrical system should be s[...]

unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt W arning Light will flash or remain on continuously . Refer to ⬙ Enhanced Driver Seat Belt Re- minder System (BeltAlert) ⬙ in the Occupant Restraints section for more information. 8. Speedometer The speedometer shows the[...]

12. T emperature Gauge The temperature gauge indicates engine coolant temperature. Any r eading within the normal range (less that the red zone) indicates that the cooling system is operating satisfactorily . The gauge needle will likely indicate a higher temperature when driving in hot weather , up mountain grades, in heavy traffic. If the needle [...]

15. CHECK GAGES This light illuminates when the V oltmeter , Engine Oil Pressur e or Engine Coolant T emperature gages indicate a reading either too high or too low . Examine the gages carefully , and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF , the Fuel Gage, V oltmeter , Oil Pressure [...]

17. ABS W arning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not fun[...]

19. LAMP OUT Light The LAMP OUT indicator in the instr ument cluster alerts the driver if a defective bulb or wiring circuit is detected for most of the exterior lamps - headlamps, turn signal lamps, and stop lamps. 20. LOW W ASH Light This light comes on when the washer fluid level falls below approximately 1/4 filled. The light will r emain on un[...]

24. Oil T emperature Gauge – if equipped This gauge shows the oil temperature. The gauge pointer will likely show higher temperatures when driving in hot weather , up mountain grades, or in heavy stop and go traffic. If this gauge r eaches the red zone you should stop the vehicle, shift into Neutral, and increase the engine idle speed for 2 to 3 [...]

SALES CODE RBQ — AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press [...]

Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it. T une Press the T[...]

5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 i[...]

Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If you insert a disc wit[...]

If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not r emoved, the radio will continue to play the non-removed CD. If the CD is removed and ther e are other CD ’ s in the radio, the radio will play the next CD. If the CD is removed and there ar e no other CD ’ s in the radio, the radio will[...]

PTY (Program T ype) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn of f. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently br oad- cast PTY information. T oggle the PTY b[...]

By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “ SEEK ” and the selected PTY program type when sear ching for the next PTY station. If no station is found with the s[...]

The right hand control is a r ocker type switch with a button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode. The left hand control is a r ocker type switch with a push button in the[...]

2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner , cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not sto[...]

CLIMA TE CONTROLS Air Conditioning with Dual Zone T emperature Control W ith the Dual Zone T emperature Contr ol System, each front seat occupant can independently contr ol the tem- perature of air coming fr om the outlets on their side of the vehicle. Air Conditioning Operation T o turn on the Air Conditioning, set the fan control at any speed and[...]

A/C Pushbutton W ith the fan control in the ON posi- tion, pushing the A/C button turns on the air conditioning compressor . An indicator light on the button shows that the Air Conditioning compr essor is on. Conditioned air is now directed through the mode outlets selected. Pushing the button a second time turns the compressor OFF . Recirculation [...]

Bi-Level Air flows through the outlets located in the instr u- ment panel and those located on the floor . NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives impr oved comfort during sunny but cool conditions. Heat Outside air flows primari[...]

Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures. Electric R[...]

edges of the instrument panel. The demisters also pr o- vide extra air ducts for circulation. They ar e in operation whenever the Floor , Mix or Defrost modes ar e in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning sys[...]

speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigar ette smoke, perfumes, etc.) from sticking to the windows. Contaminates incre[...]

Operating Tips Chart UNDERST ANDING YOUR INSTRUMENT P ANEL 147 4[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Ignition/Starter Switch ................... 1 5 2 ▫ Lock .............................. 1 5 2 ▫ O f f ............................... 1 5 2 ▫ O n................................ 1 5 2 ▫ A C C .............................. 1 5 2 ▫ Manual T ransmission Key Release Button .... 1 5 2 ▫ Key Reminder ...[...]

䡵 Power Steering ........................ 1 6 2 䡵 T ire Safety Information ................... 1 6 3 ▫ T ire Markings ........................ 1 6 3 ▫ T ire Identification Number (TIN) .......... 1 6 6 ▫ T ire Loading And T ire Pressur e ........... 1 6 7 䡵 Ti r e s — General Information ................ 1 7 1 ▫ T ire Pressur e ....[...]

䡵 Adding Fuel .......................... 1 8 6 ▫ Fuel Filler Cap (Gas Cap) ............... 1 8 6 䡵 Catalytic Converter ..................... 1 8 8 䡵 V ehicle Loading ........................ 1 8 9 ▫ Certification Label ..................... 1 8 9 䡵 T railer T owing ......................... 1 9 2 䡵 Snowplow ...........................[...]

IGNITION/ST ARTER SWITCH LOCK Engages the steering wheel lock (if equipped) when the steering wheel is turned. OFF Unlocks the steering wheel (if equipped with locking wheel). ON This is the normal running position. ACC Allows the electrical accessories to be used when the engine is not running. Manual T ransmission Key Release Button T o remove th[...]

ST ARTING PROCEDURES The starter should not be operated for more than 15- second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating. Manual T ransmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress the clutch pedal to the floor before starting the vehicle. This v[...]

Normal starting of either a cold or a warm engine does not requir e pump- ing or depressing the accelerator pedal. T o start the vehicle, turn the key to the ON position and press the r ed ENGINE ST AR T button located on the instrument panel and r elease when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OF[...]

W ARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . After Starting The idle speed is automatically controlled and will de- crease as the engine warms up. CAUTION! Long periods of engine idling, especially[...]

Damage to the clutch can re- sult from starting in 2nd or 3rd gear with a loaded ve- hicle. Use each gear in nu- merical order – do not skip a gear . For improved clutch life, all six forwar d gears should be used. For steady highway driving with light acceleration, 6th gear is recommended. When shifting fr om 4th to 5th gear , apply side effort [...]

MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS 1-2 2-3 3-4 4-5 5-6 MPH 15 25 40 45 50 (km/h) (24) (40) (65) (72) (80) Higher upshift speeds may be used to obtain a desired acceleration rate. Downshifting Moving from a high gear down to a lower gear is recommended to pr eserve brakes when driving down steep hills. In addition, downshifting at the righ[...]

The limited-slip differ ential is especially helpful during slippery driving conditions. W ith both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight momentary application of the parking brake may be necessary to [...]

Be sure the parking brake is firmly set when parked and the gear shift lever is in the REVERSE position. W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave a manual transmission in Reverse or first gear . Failure to do so may allow the vehicle to roll [...]

When parking on a hill, turn the front wheels towar d the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine of f), the brakes will still[...]

The system ’ s pump motor runs during an ABS stop to provide r egulated hydraulic pressur e. The pump motor makes a low humming noise during operation. This is normal. When you are in a sever e braking condition involving use of the Anti-lock Brake System, you will experience some pedal drop as the vehicle comes to a complete stop. This is the re[...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “ P ” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d ha[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = A[...]

EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tir e can carry . H = Speed Symbol — A symbol indicating the range of speeds at which a tir e can carry a load corresponding to its load index under certain operating conditions. — The maximum speed corresponding to the Speed Symbol should only[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: Some vehicles have a “ T ire and Loading Infor- mation ” placard located on the driver ’ s side “ B ” pillar . T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight[...]

Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire ’ s load carrying capacity if you adhere to the loading conditions, tir e size and cold tire inflation pressur es specified on the T ire and Loading Information placard and the V ehicle Loading section[...]

Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occu- pants and cargo should never exceed XXX pounds ” on your vehicle ’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and pas- sengers from XXX[...]

170 ST ARTING AND OPERA TING[...]

W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory o[...]

2. Economy — Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption. 3. Ride Comfort and V ehicle Stability [...]

The pressur e should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e underinflated. CAUTION! After [...]

T ire pressur e may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pr essure build up or your tire pr essure will be too low . T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be[...]

Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial [...]

Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spar e tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car[...]

T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent gr ooves, the ti[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can cause unpredictable handling and stress to steeri[...]

Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . SUPPLEMENT AL TIRE PRESSURE INFORMA TION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo[...]

These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es of SR T – 10 Models. NOTE: The use of class “ S ” chains is permitted on SR T – 10 Models with the use of 17 x 8 steel wheels (part number 521 13265AC) available from your authorized dealer . C[...]

TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be r educed by timely rotation of tir es. The benefits of rotation ar e es[...]

FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sion regulations and pr ovide excellent fuel economy when using high quality pre- mium unleaded gasoline having an octane rating of 91 or higher . Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage a[...]

Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with mate- rials called oxygenates such as 10% alcohol, MTBE, ETBE or T AME. Oxygenates are r equired in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygen- ates may be used in your vehicle. CAUTION! DO NOT use [...]

Sulfur In Gasoline Y our vehicle may have been designed to meet California low emission standards on clean burning, low sulfur , California gasoline. Gasoline sold outside of California is allowed to have higher sulfur levels that may affect the performance of your vehicle ’ s catalytic converter . This may cause the Malfunction Indicator Light o[...]

overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may requir e immediate service. Contact your dealer for service assistance. • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help[...]

the vehicle is raised. Have any abnormal conditions repair ed promptly . Until repaired, drive with all side windows fully open. ADDING FUEL NOTE: The fuel tank filler tube is about 2 inches (50 mm) down from the opening. If fuel is pour ed from a portable container , the container should have a flexible nozzle long enough to extend into the fuel f[...]

CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. W ARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury . • The volatil[...]

CA T AL YTIC CONVERTER The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not requir e maintenance. However , you must keep the en- gine maintained to assure pr oper operation a[...]

As with any vehicle, do not park or operate this vehicle in areas wher e combustible materials such as grass or leaves can come in contact with a hot exhaust system. A scorching odor may be detected if you continue to run a malfunctioning engine. The odor may indicate severe and abnormal catalyst overheating. If this occurs, the vehicle should be s[...]

The label also specifies maximum capacities of front and rear axle systems (GA WR). T otal load must be limited so GVWR and front and r ear GA WR are not exceeded. Payload The payload of a vehicle is defined as the allowable load weight a truck can carry , including the weight of the driver , all passengers, options and cargo. Gross Axle W eight Ra[...]

Loading The actual total weight and the weight of the front and rear of your vehicle at the gr ound can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer - cial scale to insure that the GVWR has not been exceeded. The weight on the front and r ear of the vehicle shoul[...]

NOTE: The weights shown in this chart are not necessarily the weights for your vehicle. Also, the amount of load added to both the front and rear axles can be computed after the vehicle has been weighed both in its ⴖ curb weight ⴖ condition, and in its ⴖ loaded and ready for operation ⴖ condition. Gross V ehicle W eight Rating (GVWR) 6500 L[...]

CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. W ARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual TRACTION When driving on wet or slushy roads, it is possible fo[...]

EQUIPMENT IDENTIFICA TION PLA TE The equipment Identification Plate is located on the hood inner surface. The following information about your vehicle is dis- played on this plate: Model, Wheelbase, V ehicle Identifi- cation Number , T ruck Order Number , and code numbers with descriptions of all production and special equip- ment on the truck as s[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Lights .................. 1 9 6 䡵 Adding Fuel .......................... 1 9 7 䡵 Jack Location .......................... 1 9 8 ▫ Removal ........................... 1 9 8 ▫ Reinstalling The Scissors-T ype Jack And T ools (SR T – 10 Models) ...................... 1 9 9 䡵 Changing [...]

HAZARD W ARNING LIGHTS The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column. When the Hazard W arning switch is activated, all directional turn signals will flash off and on to warn oncoming traf fic of an eme[...]

ADDING FUEL The fuel tank filler tube has a restriction about 2 inches (50 mm) inside the opening. If using a portable fuel container , it should have a flexible nozzle long enough to reach past the r estriction. W ARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. Y ou could be burned.[...]

JACK LOCA TION Removal The jack and jack tools are stor ed under the front passen- ger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. W ARNING! The jack is designed to use as a tool for changing tires only . The jack should not be used to lift[...]

Reinstalling The Scissors-T ype Jack And T ools (SRT – 10 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-scr ew . 3. Fold the flap and roll the jack tool kit into a cylindrical package (in [...]

T ying Bag to Jack with Straps Jack and T ools T ied 200 WHA T TO DO IN EMERGENCIES[...]

4. Place the jack and tools in the storage position holding the jack by the jack turn-screw , slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt. CHANGING A FLA T TIRE Removing The Spare Tire Remove the spare tir e before attempting to jack the truck[...]

It is recommended that you stow the flat or spar e to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle c[...]

W ARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or changing the wheel. • T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position. For example[...]

1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. Placement of the Jack: • When changing a front wheel, place the scissors jack under the rear portion of the lower contr ol arm as shown b[...]

• Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not requir ed. • When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending [...]

6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. Corr ect nut tightness is 90 – 11 0 ft. lbs. (125 – 150 N · m). If in doubt about the correct tightness, have them checked with a torque wr ench by your dealer or at a service station. W ARNING! A loose tire or jack thrown forward in a collision or hard stop coul[...]

Disc Wheels T ype Nut Stud Size T orque Ft. Lbs. T orque Newton Meters Cone 1/2-20 90-1 10 125-150 T o Stow The Flat Or Spare T urn the wheel so that the valve stem is down. Slide the wheel retainer thr ough the center of the wheel and position it properly acr oss the wheel opening. For convenience in checking the spare tir e inflation, stow with t[...]

JUMP-ST ARTING Y ou should not try to start your vehicle by pushing or towing. Pushing or towing a vehicle equipped with a manual transmission may overheat and damage the catalytic converter . Also, there is a greater risk of an accident when a vehicle is being pushed or towed. If the vehicle has a discharged battery , booster cables may be used to[...]

Check the Battery T est Indicator (If Equipped). If a yellow or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery . If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1. Remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact.[...]

5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery . Make sure you have a good contact on the engine. W ARNING! • Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explod[...]

W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. FREEING A STUCK VEHICLE If vehicle becomes stuck in snow , sand, or mud, it can [...]

TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to pr event damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer ’ s instr uctions. Use of safety chains is mandatory . Attach a tow bar or other towing device to the main structural members of the vehicl[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 8.3L ............... 2 1 6 䡵 Onboard Diagnostic System (OBD II) ......... 2 1 7 䡵 Emissions Inspection And Maintenance Programs ............................ 2 1 7 䡵 Dealer Service ......................... 2 1 9 䡵 Replacement Parts ...................... 2 2 0 䡵 Maintenance Pro[...]

▫ Front Suspension Ball Joints .............. 2 3 1 ▫ Steering Linkage — Inspection ............ 2 3 1 ▫ Body Lubrication ..................... 2 3 2 ▫ W indshield W iper Blades ................ 2 3 2 ▫ W indshield W ashers ................... 2 3 2 ▫ Exhaust System ...................... 2 3 3 ▫ Cooling System .....................[...]

▫ Fog Lights .......................... 2 5 7 䡵 Fluid Capacities ........................ 2 5 8 䡵 Recommended Fluids, Lubricants And Genuine Parts ......................... 2 5 9 ▫ Engine ............................. 2 5 9 ▫ Chassis ............................ 2 6 0 MAINT AINING YOUR VEHICLE 215 7[...]

ENGINE COMP ARTMENT — 8.3L 216 MAINT AINING YOUR VEHICLE[...]

ONBOARD DIAGNOSTIC SYSTEM (OBD II) Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating pr operly , your vehicle will provide excellent performance and fuel economy , as well as engine emissions well [...]

For states which have an I/M (Inspection and Maintenance) requir ement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is r eady for testing. Normally , the OBD system will be ready . The OBD system may not be ready if you[...]

b. The MIL light will r emain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle ’ s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready , you should see your dealer or repair facility . If your vehicle was recently serviced or had a battery failure or r ep[...]

W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. REPLACEMENT P ARTS Use of genuine Mopar 威 parts for normal/scheduled maintenanc[...]

Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will r esult in a SAFE reading on these engines. Change Engine Oil CAUTION! Overfilling or underfilling the [...]

• More than 50% of your driving is at sustained high speeds during hot weather , above 32 ° C (90 ° F) • T axi, Police or delivery service (commercial service) • Off-r oad or desert operation • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km[...]

Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the pr oper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). W e only recommend synthetic API Certified engine oils, such as Mo- bil 1 威 , that meet the requir ements of Material Standard MS-10725. Use Mopar or [...]

Materials Added to Engine Oil Do not add any materials (other than leak detection dyes) to engine oil. Engine oil is an engineered pr oduct and it ’ s performance may be impaired by supplemental addi- tives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oi[...]

Spark Plugs Spark plugs must fire pr operly to assure engine perfor - mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if ther e is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the cata- lytic converter . For proper type of r eplacement spark[...]

Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assur e prope[...]

W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual situations involving grossly malfunctioning engine o[...]

Check the ventilation hose for indication of damage or plugging deposits. Replace if necessary . Maintenance Free Battery The top of the maintenance free battery is permanently sealed. Y ou will never have to add water , nor is periodic maintenance requir ed. T o determine the battery charge, check the battery test indicator (if equipped) on top of[...]

W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don ’ t allow battery fluid to contact your eyes, skin or clothing. Don ’ t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water . Battery gas is flammable and explosive. Keep fla[...]

W ARNING! • Use only refrigerants approved by the manufac- turer for your air conditioning system. Some un- approved refrigerants are flammable and can ex- plode, injuring you. Other unapproved refrigerants can cause the system to fail, requiring costly repairs. • Never add air conditioning refrigerant to correct a non-cooling problem unless pr[...]

W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid f[...]

Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against r ust and wear . Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubric[...]

T o prevent fr eeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must[...]

W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, fol- low the preceding safety tips. Exhaust System Rubber Isolator and Loop-T ype Hanger — If Equipped Inspect surfaces whenever the vehicle is [...]

Check the coolant reserve tank tube for condition and tightness or connections at the reserve tank and radiator . Check the coolant pressur e cap and coolant reserve system for proper vacuum sealing. W ith the engine at normal operating temperature, note the level of the coolant in the coolant reserve tank. W ithout removing the pressur e cap (with[...]

Adding Coolant When adding coolant or refilling system, a 50% solution of ethylene glycol antifreeze coolant in water should be used. Higher concentrations (not to exceed 65%) are requir ed if temperatures below -34 F ° (-37 C ° ) are antici- pated. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze s[...]

CAUTION! Mixing of coolants other than specified (non- HOA T), may result in engine damage that may not be covered under the new vehicle warranty , and decreased corrosion protection. If a non-HOA T cool- ant is introduced into the cooling system in an emergency , it should be replaced with the specified coolant as soon as possible. Do not use plai[...]

W ARNING! The warning words “ DO NOT OPEN HOT ” on the radiator pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. T o prevent scalding or injury , do not remove the pres- sure cap. Hoses And V acuum/V apor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.[...]

The brake master cylinder has a translucent plastic reservoir . On the outboard side of the r eservoir , there is a “ MAX ” dot and an “ MIN ” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark, because leakage may occur at the cap. W ith disc brakes the fluid level can be expected to fall as the br[...]

Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hy- draulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuf fing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with poss[...]

Drain and Refill V ehicles operated in normal service do not have regularly scheduled oil changes. If fluid has become contaminated with water or to provide the corr ect viscosity grade, drain and refill. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. NOTE: The presence of water in the gear lub[...]

the transmission. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary , to maintain the proper level. Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. If the vehicle is operated under severe conditions, change[...]

quality level available and when combined as shown can be used for both wheel bearing and chassis lubrication. Use only those greases that have the NLGI symbol on the container along with the proper quality level for your application. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir[...]

W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water . • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible. • Use Mopar 威 auto polish to remove r oad film and stains and to polish [...]

• If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating have your vehicle repair ed as soon as possible. The cost of such repairs is consider ed the responsibil- ity of the owner . • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned r egularly with[...]

and Mopar 威 T otal Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition. W ARNING! Do not [...]

Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts fr om the car to wash them. Replace the belts if they appear frayed or worn or [...]

2. Use specified fuses only . 3. Always properly reinstall the cover . VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle ’ s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Fuse and Relay Center , located in[...]

BULB REPLACEMENT Headlight (Halogen)/Front Park and T urn Lights CAUTION! This is a halogen bulb. A void touching the glass with your fingers. Reduced bulb life will result. 1. Remove the two (2) expanding fasteners from the headlight welt. MAINT AINING YOUR VEHICLE 249 7[...]

2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperatur e sensor between the headlight assembly and the frame. 250 MAINT AINING YOUR VEHICLE[...]

MAINT AINING YOUR VEHICLE 251 7[...]

3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. T wist connector on turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 6. Remove housing from vehicle with headlight halogen bulb in h[...]

T ail, Stop, T urn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. 2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged. 3. Push the red lock slide in on the connector and remove the housing from the vehicle.[...]

4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip. • T op Bulb: Park/T urn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 254 MAINT AINING YOUR VEHICLE[...]

6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. MAINT AINING YOUR VEHICLE 255 7[...]

2. Separate the connector holding the housing and wir- ing harness to the body . 3. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. 2[...]

Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1 ⁄ 4 turn and remove connector and bulb from housing. 2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing. MAINT AINING YOUR VEHICLE 257 7[...]

FLUID CAP ACITIES U.S. Metric Fuel SR T -10 Models 26 gal. 98L Engine Oil (with filter) 8.3L 8.5 qts. 8.0L Cooling System 8.3L 20 qts. 19L 258 MAINT AINING YOUR VEHICLE[...]

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/102,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) P/N 05066386AA or equivalent. Engine Oil W e only recommend synthetic engine oils, such as Mobil 1 威 , that ar e API Certifie[...]

Chassis Component Fluids, Lubricants and Genuine Parts. T ransmission Fluid Mopar Synthetic Manual T ransmission Lubricant 75W/85W (Castrol Syn- torq L T 75W/85W) Clutch Linkage Multipurpose Grease, NLGI Grade 2 E.P . Limited-Slip Rear Axle Mopar 威 SAE 90W . Limited-Slip Rear Axles requir e the addition of 147 ml (5 oz.) Mopar 威 limited slip ad[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 2 6 2 䡵 Maintenance Schedules ................... 2 6 2 ▫ Schedule “ B ” ........................ 2 6 5 ▫ Schedule “ A ” ........................ 2 7 4 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “ Scheduled ” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best [...]

• Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “ B ” of the ⬙ Maintenance Schedules ⬙ section of this manual. NOTE: Most vehicles are operated unde[...]

At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if requir ed.[...]

Schedule “ B ” Follow schedule “ B ” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32 ° F( 0 ° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your dri[...]

Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) Change engine oil and engine oil filter . X X X X X Change rear axle fluid. X Inspect brake linings. X Inspect engine air cleaner filter , replace if neces- sary . X 266 SCHEDULE “ B ” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) Change engine oil and engine oil filter . X X X X X Change rear axle fluid. X Inspect brake linings. X Inspect engine air cleaner filter , replace if neces- sary . X Replace spark plugs. X Inspect and replace, if necessary , the PCV orifice. X* SCHEDU[...]

Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) Change engine oil and engine oil filter . X X X X X Change rear axle fluid. X Inspect brake linings. X Inspect engine air cleaner filter , replace if neces- sary . X 268 SCHEDULE “ B ” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) Change engine oil and engine oil filter . X X X X X Change rear axle fluid. X Inspect brake linings. X X Inspect engine air cleaner filter , replace if neces- sary . X Replace spark plugs. X Replace ignition cables. X Inspect and replace, if necessary[...]

Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (101 000) (106 000) (110 000) (1 15 000) (120 000) Change engine oil and engine oil filter . X X X X X Inspect engine air cleaner filter . X Change rear axle fluid. X Inspect brake linings. X Inspect auto tension drive belt and replace if r e- quired. X 270 SCHEDULE “ B ” 8 M A I N T E N A N[...]

Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . X X X X X Change rear axle fluid. X Inspect brake linings. X Inspect engine air cleaner filter , replace if neces- sary . X Replace spark plugs. X Inspect PCV valve, replace as necessary . X* Inspect auto[...]

Miles 93,000 96,000 99,000 100,000 102,000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) Change engine oil and engine oil filter . X X X X Flush and replace engine coolant. X Flush and replace Power Steering Fluid. X Inspect brake linings. X 272 SCHEDULE “ B ” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 105,000 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (168 000) (173 000) (178 000) (182 000) (187 000) (192 000) Change engine oil and engine oil filter . X X XXXX Change rear axle fluid. X X Inspect brake linings. X X Inspect engine air cleaner filter , replace if necessary . XX Replace spark plugs. X Replace ignition cables. X I[...]

Schedule “ A ” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X X X X Inspect brake linings. X Replace engine air cleaner filter . X Replace spark plugs. X 274 SCHEDULE “ A ” 8 M A I N T E N A N C E S C H E D U L E[...]

Miles 36,000 42,000 48,000 54,000 60,000 66,000 (Kilometers) (58 000) (67 000) (77 000) (84 000) (96 000) (106 000) [Months] [36] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X XXXX Flush and replace engine coolant at 60 months, regar dless of mileage. X Inspect brake linings. X X Replace engine air cleaner filter . X Replac[...]

Miles 72,000 78,000 84,000 90,000 96,000 100,000 (Kilometers) (1 15000) (125 000) (134 000) (144 000) (154 000) 160 000 [Months] [72] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X X Flush and replace Power Steering Fluid. X Inspect brake linings. X X Replace engine air cleaner filter . X Replace spark plugs. X Inspect and re[...]

Miles 102,000 108,000 114,000 120,000 (Kilometers) (163 000) (173 000) (182 000) (192 000) [Months] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X X Flush and replace engine coolant, if not done at 60 mos. X Inspect brake linings. X Inspect auto tension drive belt and replace if r equired. X ‡ X ‡ Replace ignition cabl[...]

W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. 278 SCHEDULE “ A ” 8 M A I N T E N A N C E S C H E D U L E S[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 2 8 0 ▫ Prepar e For The Appointment ............ 2 8 0 ▫ Prepar e A List ........................ 2 8 0 ▫ Be Reasonable W ith Requests ............. 2 8 0 䡵 If Y ou Need Assistance ................... 2 8 0 䡵 [...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you ’ re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle ?[...]

The manufacturer has empower ed its dealers to make warranty and repair decisions that ensur e you are not inconvenienced. There is no need for you to wait for a decision from the manufactur er . If a special circumstance occurs that requir es information from the manufactur er , we have asked the dealer ’ s service management to make the contact[...]

DaimlerChrysler Canada Inc. Customer Center P .O. Box 1621 W indsor , Ontario N9A 4H6 Phone — (800) 465 – 2001 In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico (915) 729 – 1248 or 729 – 1240 Outside Mexico (525) 729 – 1248 or 729 – 1240 Customer Assistance For The Hearing Or S[...]

The manufacturer will not stand behind any service contract that is not the manufacturer ’ s Service Contract. It is not responsible for any service contract other than the manufacturer ’ s Service Contract. If you pur chased a service contract that is not a manufacturer ’ s Service Contract, and you requir e service after your manufactur- er[...]

284 IF YOU NEED CONSUMER ASSIST ANCE[...]

MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immedi[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is requir ed when ordering manuals. (No P .O. Boxes). •[...]

Call T oll Free at 1 – 800 – 890 – 4038 (U.S.) or 1 – 800 – 387 – 1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .daimlerchrysler .com or www .daimlerchrysler .ca/manuals IF YOU NEED CONSUMER ASSIST ANCE 287 9[...]

[...]

INDEX 10[...]

Adding Fuel ........................ 186,197 Additives, Fuel ......................... 1 8 4 Air Cleaner , Engine ...................... 2 2 5 Air Conditioner Maintenance ............... 2 2 9 Air Conditioning Refrigerant ............... 2 2 9 Air Conditioning System .................. 2 2 9 Air Conditioning System, Zone Control ........ 1 4 1 Air [...]

Hoses .............................. 2 4 0 Master Cylinder ....................... 2 3 8 Parking ............................. 1 5 8 W arning Light ........................ 1 2 8 Break-In Recommendations, New V ehicle ........ 5 7 Bulb Replacement ....................... 2 4 9 Bulbs, Light ............................ 2 4 8 Button, Start ..........[...]

Compass Calibration ..................... 1 0 3 Compass V ariance ....................... 1 0 4 Computer , T rip/T ravel .................... 1 0 0 Console, Overhead ....................... 9 9 Contract, Service ........................ 2 8 2 Converter , Catalytic ...................... 1 8 8 Cooling System ......................... 2 3 4 Coolant C[...]

Emergency , In Case of Freeing V ehicle When Stuck ............... 2 1 1 Hazard W arning Flasher ................. 1 9 6 Jacking ............................. 2 0 2 Jump Starting ......................... 2 0 8 T owing ............................. 2 1 2 Emission Control System Maintenance ......... 2 6 2 Engine ............................... 2 1 [...]

Fog Lights ........................... 89,257 Four-W ay Hazard Flasher .................. 1 9 6 Freeing A Stuck V ehicle ................... 2 1 1 Front Axle ............................. 2 4 0 Front Wheel Bearings ..................... 2 4 2 Fuel ................................. 1 8 2 Adding ............................. 1 8 6 Filter ............[...]

Hoisting .............................. 2 0 7 Homelink T ransmitter .................... 1 0 6 Hood Release ........................... 8 4 Hoses ................................ 2 3 8 Ignition ............................. 14,152 K e y ............................... 1 1,14 Lock ................................ 1 4 Infant Restraint ...............[...]

Courtesy/Reading ...................... 9 9 Cruise .............................. 1 2 7 Daytime Running ....................... 8 9 F o g .............................. 89,257 Hazard W arning Flasher ................. 1 9 6 Headlights ............................ 8 8 High Beam ......................... 91,125 High Beam Indicator ...................[...]

Schedule ⬙ B ⬙ .......................... 2 6 5 Malfunction Indicator Light ................ 2 1 8 Manual, Service ......................... 2 8 6 Manual T ransmission ..................... 1 5 5 Lubricant Selection ..................... 2 6 0 Mirrors ................................ 6 5 Automatic Dimming ..................... 6 5 Electric Powe[...]

Passing Light ........................... 9 1 PCV V alve ............................ 2 2 7 Pedals, Adjustable ........................ 9 5 Phone, Cellular .......................... 6 7 Phone, Hands-Free ....................... 6 7 Pickup Box ............................ 1 1 6 Placard, T ire and Loading Information ......... 1 6 7 Power Distributi[...]

Safety Checks Inside V ehicle ................. 6 0 Safety Checks Outside V ehicle ............... 6 0 Safety Defects, Reporting .................. 2 8 5 Safety Information, T ire ................... 1 6 3 Safety T ips ............................. 5 8 Schedule, Maintenance .................... 2 6 2 Seat Belt Maintenance .................... 2 4 7[...]

Spark Plugs ............................ 2 2 5 Speed Control ........................... 9 6 Speedometer ........................... 1 2 6 Start Button ............................ 1 5 3 Starting ............................... 1 5 3 Engine Fails to Start .................... 1 5 4 Manual T ransmission ................... 1 5 3 Steering Column Cont[...]

Jacking ............................. 2 0 2 Load Capacity ..................... 167,168 Radial .............................. 1 7 5 Replacement ......................... 1 7 7 Rotation .......................... 181,264 Safety ........................... 163,171 Sizes ............................... 1 6 4 Snow T ires ........................... 1 8[...]

W arning Lights (Instrument Cluster Description) . 124 W arnings and Cautions ..................... 5 W arranty Information ..................... 2 8 3 W ashers, W indshield ................... 93,232 W ashing V ehicle ......................... 2 4 4 Wheel Alignment and Balance ............... 1 7 8 Wheel and Wheel T rim .................... 2 4 5 [...]