Dodge 2007 DH Ram manuel d'utilisation

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 7 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ...................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 A Message From DaimlerChrysler Corporation . . . 5 䡵 How T o Use This Manual .................. 5 䡵 W arnings And Cautions ................... 7 䡵 V an Conversions/Campers ................. 7 䡵 V ehicle Identification Number ............... 8 䡵 V ehicle Modifications[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

A MESSAGE FROM DAIMLERCHR YSLER CORPORA TION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins T urbo Diesel- powered tr uck owner . Almost 100% of the heavy duty trucks in the United States are diesel power ed because of the fuel economy , rugged durability , and high torque which permits pulling heavy loads. Cummins e[...]

6 INTRODUCTION[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. V AN CONVER[...]

VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is found on the left front corner of the instr ument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label af fixed to a window on your vehicle, the vehicle registration and title. NOTE: It is illegal to remove the VIN. [...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 2 ▫ Ignition Key Removal ................... 1 2 ▫ Locking Doors W ith The Key .............. 1 4 䡵 Steering Wheel Lock — If Equipped .......... 1 5 ▫ If Y ou W ish T o Manually Lock The Steering Wheel ........................ 1 5 ▫ [...]

▫ T o Unlock The Doors ................... 2 0 ▫ T o Lock The Doors ..................... 2 1 ▫ Using The Panic Alarm .................. 2 2 ▫ General Information .................... 2 2 ▫ T ransmitter Battery Service ............... 2 3 䡵 Door Locks ............................ 2 4 ▫ Manual Door Locks ..................... 2 4 ▫ P[...]

▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag ............ 4 5 ▫ Event Data Recorder (EDR) ............... 5 6 ▫ Child Restraint ........................ 5 7 䡵 New Engine Break-In ..................... 7 1 䡵 Safety T ips ............................ 7 2 ▫ T ransporting Passengers ................. 7 2 ?[...]

A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer . Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic T ransmission Place the shift lever in P ARK. T urn the ignition switc[...]

NOTE: If you try to remove the key befor e you place the lever in P ARK, the key may become trapped temporarily in the ignition cylinder . If this occurs, rotate the key to the right slightly , then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is ino[...]

Manual T ransmission—If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your vehicle. It may be dif ficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily[...]

STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key . If the steering wheel is moved no more than 1/2 turn in either dir ection and the key is not in the ignition switch, the steering wheel will lock. If Y ou Wish T o Manually Lock T[...]

the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine. NOTE: A key , which has not been programmed, is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the V ehicle Secur[...]

NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key T ransponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into th[...]

General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interfer ence that may cause undes- ired operation. SECURITY[...]

NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer . T o Disarm the System: Use the Keyless Entry transmitter to unlock the door . If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 se[...]

REMOTE KEYLESS ENTR Y — IF EQUIPPED This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter . The transmitter need not be pointed at the vehicle to activate the system. T o unlock the doors: Press and r elease the UNLOCK button on the key fob once to unlock only the driv[...]

5. This will enable you to unlock all doors on the first press of the UNLOCK button. T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped fr om the ass[...]

Using the Panic Alarm T o activate the Panic mode while the ignition is OFF press and release the P ANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound. T o cancel the Panic mode press and r elease the P ANIC button on the tr[...]

T ransmitter Battery Service The recommended r eplacement battery is a 3V lithium 2016 cell. This transmitter requir es two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit boar d. 1. W ith transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart.[...]

DOOR LOCKS Manual Door Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger . Doors locked before closing will remain locked when closed. The ignition key will unlock all the locks on your vehicle. W ARNING! • For personal security and[...]

Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you fr om acciden- tally locking your keys in the vehicle. Remo[...]

2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming pr ocedure). 3. Place the key into the ignition. 4. W ithin 15 seconds cycle the key from the LOCK position to the ON/RUN position a minimum of four times; ending in the LOCK position (do not start the engine) 5. W ithin 30 seconds[...]

4. W ithin 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine) . 5. W ithin 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. Repeat the above steps to a[...]

slide the lever UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be [...]

WINDOWS Power Windows—If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of Quad Cab and Mega Cab models. The windows will operate only when the [...]

W indow Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. T o disable the window controls on the other doors, pr ess the window lock button. T o enable the window controls, press the window contr ol button again. Power Sliding Rear Window—If Equipped T[...]

Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry fr om the rear of the vehicle. Squeeze the lock to release the window . Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with[...]

W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly . Buckle up even though you are an excellent driver [...]

W ARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a[...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around you[...]

W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increas- ing the po[...]

4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! • A lap belt worn too high can increase[...]

5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The r etractor will withdraw any slack in the belt. 6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to re[...]

The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus fr eeing up all the area behind the fr ont seats. 2. T o reattach the seat belt to the fr ont center seat, pull the black buckle latch plate [...]

W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing i[...]

W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located [...]

As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Restraint (ALR) Mode – If Equipped In this mode, the shoulder belt is automa[...]

3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How T o Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensi[...]

NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the airbag contr ol module. Like the airbags, the pretensioners ar e single use items. After a collision that is severe enough to deploy the airbags and prete[...]

3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled. 4. T urn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced W arning System (BeltAlert) can be reacti- [...]

W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver And Right Front Passenger Supplemental Restraint Syste[...]

W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not mount any aftermarket equipment[...]

Here ar e some simple steps you can follow to minimize the risk of harm from a deploying airbag. • Children 12 years and under should ride buckled up in a rear seat, if available. • Infants in rear facing child r estraints must NEVER ride in the front seat of a vehicle with a passenger fr ont airbag unless the airbag is turned off (Standar d Ca[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instru- ment panel during airbag de[...]

The W indow Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the fr ont airbag system) • W indow Bags Above the Side W indows. • Airbag Control Module (shar ed with the front airbag system) • Side impact sensors • Interconnecting W iring How The Airbag System W orks • The airbag contr[...]

W ARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away . • When the airbag control module detects a collision requiring the air[...]

Passenger Airbag On/Off Switch – (Standard Cab V ehicles Only) The passenger front airbag is to be turned of f only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because ther e is no rear seat, because the r ear seat is too small for a rear -facing infant restraint or because the infant has a medical co[...]

W ARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. T o Shut Off the Passenger Airbag (Standard Cab V e- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch,[...]

If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold. The abrasions are similar to friction r ope burns or those you might get sliding along a carpet or gymna[...]

W indow Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to r equire the side airbags to inflate. The window airbag control module will not detect roll over , front or r ear collisions. The airbag control module monitors the r eadiness of the electronic parts [...]

Maintaining Y our Airbag Systems W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right[...]

for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your dealer if the fuse is good. Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is designed to recor d up to 2-seconds of specific vehicle data parameters (see the following list) in the event data recor d[...]

nature, such as would identify a particular driver , ve- hicle, or crash, will be treated confidentially . Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1. Used for resear ch purposes, such as to match data with a particular crash recor d in an aggregate database, provided confidentiality o[...]

Children 12 years and under should ride pr operly buck- led up in a rear seat, if available. According to crash statistics, children ar e safer when properly r estrained in the rear seats rather than in the fr ont. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold[...]

infant carriers do, so they can be used rearwar d-facing by children who weigh mor e than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a fr ont passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants i[...]

W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat, or in the fr[...]

Pull the belt from the r etractor until there is enough to allow you to pass through the child r estraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed fr om the retractor . Allow the belt to return to the r etractor , pulling on the excess web- bing to tighten the lap portion about the child re- straint. [...]

W ARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when install- ing an infant or child restraint. Lower Anchors and T ether for CHildren (LA TCH) Each vehicle is equipped with the child re[...]

Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for Quad Cab Rear Outboard Seats Mega Cab Rear Seats THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 63 2[...]

some time. In fact, many child restraint manufactur ers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be intr oduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor - ages will continue to have features for installation i[...]

Installing the Child Restraint System W ARNING! Do not install child restraint systems equipped with LA TCH attachments in the center position of a Quad Cab model rear seat. The LA TCH anchorages in this seat are designed for the two outboard seating posi- tions only . A child may be placed in the rear center seating position of a Quad Cab model us[...]

W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Child Restraint T ether Anchor Child restraints having tether straps and hooks for[...]

2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufactur er’s instructions. Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and r[...]

5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor dir ectly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child r estraint manufactur- er’s i[...]

Multiple Child Restraint Quad Cab THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 69 2[...]

T ether Anchorage Points at All Three Seating Positions (Mega Cab) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor dir ectly behind the seat. 2. Lift the cover , and attach the hook to the square opening in the sheet metal. 3. Install the chi[...]

• The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their b[...]

CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer . Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. SAFETY TIPS T ransporting Passengers This vehicle is designed to carry passengers in the cab only . For safety reasons, NEVER TR[...]

Exhaust Gas W ARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. T o avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If i[...]

Safety Checks Y ou Should Make Inside The V ehicle Heater Defroster Ducts Inspect the heater defroster ducts for pr oper operation. Check for proper air flow thr ough all defroster ducts. If there ar e any question regar ding the operation of your heater defroster ducts, have the system checked by an authorized dealer Seat Belts Inspect the belt sy[...]

Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water , oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be loc[...]

[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 8 2 ▫ Inside Mirror ......................... 8 2 ▫ Automatic Dimming Mirror— If Equipped .... 8 3 ▫ Outside Mirrors ....................... 8 3 ▫ Exterior Mirrors Folding Featur e ........... 8 4 ▫ Electronic Power Mirr ors — If Equipped[...]

▫ Reclining Seats ....................... 1 1 1 ▫ Adjustable Head Restraints .............. 1 1 1 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped ......................... 1 1 2 ▫ Power Seats — If Equipped .............. 1 1 3 ▫ Rear Seat Features — Mega Cab Models ..... 1 1 4 ▫ Heated Seats — If Equipped ............. 1[...]

䡵 Electronic Speed Contr ol — If Equipped ...... 1 3 3 ▫ T o Activate .......................... 1 3 3 ▫ T o Set At A Desir ed Speed ............... 1 3 4 ▫ T o Deactivate ........................ 1 3 4 ▫ T o Resume Speed ..................... 1 3 4 ▫ T o V ary The Speed Setting ............... 1 3 4 ▫ T o Accelerate For Passing ...[...]

▫ Canadian Programming/Gate Pr ogramming . . 147 ▫ Using HomeLink ..................... 1 4 8 ▫ Erasing HomeLink Buttons .............. 1 4 8 ▫ Reprogramming a Single HomeLink Button . . . 148 ▫ Security ............................ 1 4 9 䡵 Power Sunroof — If Equipped ............. 1 4 9 ▫ Open Sunroof - Expr ess Mode ............ 1[...]

䡵 Storage .............................. 1 5 9 ▫ Center Storage Compartment (40–20–40 Seat) — If Equipped ......................... 1 5 9 ▫ Center Storage Compartment (Bucket Seats)— If Equipped ......................... 1 6 0 ▫ Storage And Seats (Quad Cab Models) ...... 1 6 2 ▫ Storage And Seats (Mega Cab Models) ...... 1 6 2 ▫[...]

MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the r ear window . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Adjusting Rear V iew Mirror 82 U[...]

Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cleaning, [...]

W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mir[...]

Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move. Electric[...]

NOTE: Fold th e7x1 0 inch trailer towing mirrors rearward prior to entering an automated car wash. Blindspot Mirror T railer T owing Position 86 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ). Y our cellular phone?[...]

The rearview mirr or contains the microphone for the system and the control buttons that will enable you to access the system. The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones. If your cellular phone supports a differ ent profile (e.g., Heads[...]

• Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙ Ready ⬙ prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying ⬙ Setup ⬙ and then ⬙ Phone Pairing, ⬙ the following compound command can be said: ⬙ Setup Phone Pairing. ⬙ • For e[...]

Pair (Link) UConnect™ System to a Cellular Phone T o begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requir es a cellular phone equipped with the Bluetooth ⬙ Hands-Free Pr ofile, ⬙ version 0.96 or higher . See www .chrysler .com/uconnect for supported pho[...]

• Y ou will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority . Y ou can pair up to seven cellular phones to your UConnect™ system. However , at any given time, only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know wh[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a pr evi- ously stored name entry in the UConnect™ phone- book. Refer to ⬙ Add Names to Y our UConnect™ Phonebook, ⬙ to learn how to store a name in the phonebook. • The UConn[...]

four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep,[...]

• After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. Y ou can either say the name of a phonebook entry that you wish to delete or you can say ⬙ List Names ⬙ to hear a list of the entries in the phonebook from which you choose. T o select one of the entries from the list, pr ess[...]

• T o call one of the names in the list, press the ⬙ V oice Recognition’ button during the playing of the desired name, and then say ⬙ Call. ⬙ NOTE: the user can also exercise ⬙ Edit ⬙ or ⬙ Delete ⬙ operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected[...]

Making a Second Call while Current Call in Progress T o make a second call while you are curr ently in a call, press the ’V oice Recognition’ button and say ⬙ Dial ⬙ or ⬙ Call ⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progr ess. T o go back to the first[...]

Call T ermination T o end a call in progr ess, momentarily press the ⬘ Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The UConnect™ [...]

• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UCon[...]

Y our phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. T owing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the f[...]

When calling a number with your UConnect™ system that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send. ⬙ For example, if requir ed to enter your pin number followed with a poun d3746# ,y o[...]

Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played throug[...]

Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc. related information. Advanced Phone Connectivity T ransfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred f[...]

Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously pair ed to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Select Phon[...]

• Speak normally , without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth ro[...]

• Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, a[...]

106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 107 3[...]

108 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up [...]

40-20-40 Front Seat As the name implies, the seat is divided into 3 segments. The outboard seat portions ar e each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armr est/center storage compartment (if equipped). Each outboard seat is independently adjustable forwar d or rearwar d and is equ[...]

Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. W ARNING! Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting again[...]

T o lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decr eases the lumbar (lower back) support. Head Restraints M[...]

Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. The power seat controls ar e on the outboard side of the front seat cushions. Thr ee switches control the seat move- ment. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable posi- tion[...]

control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Rear Seat Features — Mega Cab Models Reclining Rear Seats — Mega Cab Models The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. T ilt Adjustment Rear Seat Re[...]

Folding Rear Seat (T able Mode) — Mega Cab Models Both the left and right rear seat backs can be folded down and used as a table. T o fold either rear seat back down (T able Mode), lift the handle and fold the seat back forward. Simply lift the seat back to return the seat to the upright position. V erify that it is locked in place. T able Mode H[...]

Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the r ear seat backs provide 2 D-rings and each of the r ear storage bin lids provide 2 slotted cutouts. Use a car go tie down to secure car go in the cargo carrying ar ea. T able Mode Securing C[...]

W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat[...]

T o fold either rear seat flat (Kneel Mode), lift the handle and fold the seat forward. Simply lift the seat back to return the seat to the upright position. V erify that it is locked in place. Kneel Mode Handle Kneel Mode 1 18 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

W ARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury . Heated Seats — If Equipped The heated seat switches are located in the instr ument p[...]

level, or OFF . The High heat level operates for 30 minutes (approximate), the Low heat level operates for 30 min- utes (approximate). The seat heat will also turn OFF when the ignition is turned OFF . Both of the indicators ON identifies High heat level. The lower indicator On only , identifies Low heat level. Flashing indicator lights on the swit[...]

TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must r each into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood. T o[...]

W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. LIGHTS Headlight Switch Location 122 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

Interior Lights Courtesy and dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob. When a door is open and the interior lights are on, r otating the dimmer cont[...]

Battery Saver T o protect the life of your vehicle’s battery , Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is r otated upwards for 10 minutes, the interior lights will automatically turn off. If the headlamps remain on while the igniti[...]

Y our vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone br eakage than glass headlights. Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedur es must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with [...]

Lights-on Reminder If the headlights, parking lights, or cargo lights ar e left on, after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The foglights are turned ON by placing the head- light rotary contr ol in the parking light or head- light position and pushing in the headlight rotar[...]

Multifunction Control Lever The multifunction control lever is located on the left side of the steering column. T urn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instr ument cluster flashes to indicate the direction of the turn, and pr oper operation of the front and r ear turn signal [...]

Passing Light Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headligh[...]

WINDSHIELD WIPERS AND W ASHERS Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed. Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variab[...]

W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with defroster before and during wind- shield washer use. Windshield W ashers T o use the washer , push in on the washer kn[...]

W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. T ilt Steering Control Lever UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 131 3[...]

DRIVER ADJUST ABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and[...]

CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at [...]

T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, clutch pressur e while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed cont[...]

T o decrease speed while the speed contr ol is on, press and hold the DECEL button. Release the button when the desired speed is r eached, and the new speed will be set. T o Accelerate For Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. NOTE: When driving uphill, at elev[...]

OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Courtesy/Reading Lights • Compass/T emperature Mini-T rip Computer (CMTC) — If Equipped • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/r eading lights. Both lights [...]

OVERHEAD CONSOLE WITH COMP ASS/TEMPERA TURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/T emperature Mini-T rip Computer (CMTC) This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored. US/M Butt[...]

RESET Button Use this button to reset the following displays: A verage Fuel Economy (A VG ECO) T rip Odometer (ODO) Elapsed time (ET) Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays (A VG ECO, ODO, ET), the Global Reset will reset all 3 displays. Step Button Use this button to choose or c[...]

A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. A verage fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled. When the fuel economy is reset, the display will momen- tarily blank. Then, the history information will be erased, and the averaging will continue fro[...]

Ram fuel tank volumes are as follows: • 26 gallons - 1500 short box models • 34 gallons - 1500 Quad Cab (if equipped)/2500/3500 short box models • 35 gallons - 1500/2500/3500 long box models T rip Odometer (ODO) This display shows the distance traveled since the last reset. Resetting of this scr een will cause the trip odometer to change to Z[...]

W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to ma[...]

Compass V ariance is the difference between magnetic north and geographic north. In some areas of the country , the differ ence between magnetic and geographic north is great enough to cause the compass to give false r eadings. If this occurs, the compass variance must be set according to the Compass V ariance Map. 142 UNDERST ANDING THE FEA TURES [...]

NOTE: The default for the compass variance is zone 8. T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resum[...]

For additional information on HomeLink 威 , call 1–800– 355–3515, or on the internet at www .homelink.com. W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” fea[...]

Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal. 1. Press and hold the two outer Hom[...]

3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed. NOTE: Some gate operators and garage door openers may requir e you to replace this Pr ogramming Step 3 with procedur es noted in the ⬙ Gate Operator/Canadian Pro- gra[...]

8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖ press/hold/release ⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), r epeat this sequence a third time to complete the pr ogramming. HomeLink should now [...]

Using HomeLink T o operate, simply press and r elease the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener , gate operator , security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that ther[...]

Security If you sell your vehicle, be sure to erase the fr equencies. T o erase all of the previously trained fr equencies, hold down both outside buttons until the green light begins to flash. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may no[...]

W ARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • In an accident, there is a greater risk o[...]

Closing Sunroof - Express Press the switch forwar d and release, and the sunr oof will close automatically from any position. The sunr oof will close fully and stop automatically . This is called Express Close. During Expr ess Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstr [...]

Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with[...]

The outlet(s) has/have a fused direct feed fr om the battery so it/they receive power whether the ignition is ON or OFF . All accessories connected to this/these outlet(s) should be removed or turned OFF when the vehicle is not in use to protect the battery against dischar ge. NOTE: If desired, all of the power outlets can be converted by your auth[...]

CIGAR LIGHTER AND ASH RECEIVER The removable ash r eceiver is located in the instrument panel cup holder tray . The cigar lighter is located on the instrument panel, above and to the left of the ash receiver . As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when[...]

CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic T ransmission Y our new Ram truck is equipped with two adjustable cupholders. The cupholder is opened by pulling on the cup holder door handle, on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. T o secure the[...]

Cup Holder Door Handle Cup Holders Automatic T ransmission 156 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

Front Instrument Panel Cupholders (Bucket Seats) — Automatic T ransmission If your new Ram truck is equipped with bucket seats there ar e three cup holders located on the fr ont of the center console. Front Instrument Panel Cupholders — Manual T ransmission Cup Holders Bucket Seat Cup Holders Manual T ransmission UNDERST ANDING THE FEA TURES OF[...]

Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience. Rear Cupholder — Mega Cab Mega Cab vehicles are equipped with r ear cupholders located in the center armrest. Mega Cab Rear Armrest Cup Holder 158 UNDERST ANDING THE FEA TURES OF YOUR [...]

STORAGE Center Storage Compartment (40–20–40 Seat) — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armr est to raise the cover . Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers t[...]

CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, va[...]

storage area into separate compartments. Lift the lower handle on the front of the armr est, and raise the armrest for access to the lower storage bin. On Quad Cab and Mega Cab models the rear of the floor console of fers a power outlet, a tip out bin and a rear air duct (Mega Cab Only). W ARNING! • This armrest is not a seat. Anyone seated on th[...]

Storage and Seats (Quad Cab Models) Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat. Lift the seat to access the storage compart- ment. Storage and Seats (Mega Cab Models) The Mega Cab mo[...]

Push down on the front of the storage compartment handle and lift the storage compartment cover . The rear storage compartment can be divided into thr ee separate compartments by using the divider doors inside the storage compartment. Mega Cab Rear Storage Compartment Handle Mega Cab Rear Storage Dividers UNDERST ANDING THE FEA TURES OF YOUR VEHICL[...]

Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. REAR WINDOW FEA TURES Electric Rear Window Defroster and Heated Side view Mirrors — If Equipped The Electric Rear W indow Defroster and Heated side view mirrors ar e activated b[...]

Power Sliding Rear Window—If Equipped The power sliding rear window switch is located on the instrument panel below the climate contr ols. Press the right side of the switch to open the glass and the left side of the switch to close the glass. Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry fr[...]

FOLD FLA T LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat, may be equipped with a folding load floor . W ARNING! Do not operate the vehicle with loose items stored on the load floor . While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may[...]

Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to stor e the load floor . Unfolding The Load Floor Load Floor In Open Position UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 167 3[...]

Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor . 3. Lift the load floor up to access storage under the load floor . W ARNING! Do not drive with the load floor in the up position. When stopping fast or in an ac[...]

PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar 威 toolbox brackets available from your dealer . Y ou can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor . Place lumbe[...]

W ARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo. V ehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. If wide building materials are to be frequently carried, the installation of a support is recommended. This[...]

EASY -OFF T AILGA TE T o simplify mounting of a camper unit with an overhang, the tailgate can be removed quickly . If the truck is a 3500 dual rear wheel model, unplug the tailgate wir e harness from under the r ear of the truck and pull the harness out of the cargo box access hole. Unlatch the tailgate and remove the support cables by r eleasing [...]

W ARNING! T o avoid inhaling carbon monoxide, which is deadly , the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. T AILGA TE SUPPOR T STRAP A TT ACHMEN 172 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Controls ................. 1 7 7 䡵 Instrument Cluster ...................... 1 7 8 䡵 Instrument Cluster Description ............. 1 7 9 䡵 Electronic Digital Clock .................. 1 8 7 ▫ Clock Setting Procedur e................. 1 8 8 䡵 Radio General Information .......[...]

▫ Operating Instructions - Satellite Radio — If Equipped ........................... 1 9 7 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio W ith Optional Satellite Radio, Hands Free Phone, And V ehicle Entertainment Systems (VES) Capabilities ........................... 1 9 8 ▫ Operating Instructions - Radio Mode ....... 1 9 8 ▫ Operation In[...]

▫ Noise Reduction ...................... 2 1 7 ▫ Operation Instructions - (CD Mode For CD Audio Play) .............................. 2 1 7 ▫ Load/Eject Button (CD Mode For CD Audio Play) ......................... 2 1 8 ▫ Notes On Playing MP3 Files ............. 2 2 0 ▫ Operation Instructions - (CD Mode For MP3 And WMA Audio Play) ........[...]

▫ Satellite Antenna ...................... 2 3 0 ▫ Reception Quality ..................... 2 3 0 䡵 Remote Sound System Controls — If Equipped ........................... 2 3 1 ▫ Radio Operation ...................... 2 3 1 ▫ T ape Player ......................... 2 3 2 ▫ CD Player .......................... 2 3 2 䡵 Cassette T ape An[...]

INSTRUMENTS AND CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 177 4[...]

INSTRUMENT CLUSTER 178 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages This light illuminates when the V oltmeter , Engine Oil Pressur e or Engine Coolant T emperature gages indicate a reading either too high or too low . Examine the gages carefully , and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF , the Fuel Ga[...]

CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur . 5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on. If the light stays on, flickers or comes on while driving, have the airbag system checked by an authorized [...]

NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. T ransfer Case Position (See page 273 for more information.) 11 . TOW HAUL The TOW HAUL button is located at the end of the gear shift lever . This light will illuminate when the TOW HAUL OD/OFF button [...]

CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to impr ove engine cooling. NOTE: If the gauge pointer moves to either extreme of the gauge, th[...]

NOTE: There is also an engine hour function. This indicates the total number of hours the engine has been running. T o display the engine hours perform the follow- ing: Place the ignition in RUN, but do not start the engine. W ith the odometer value displayed, hold the trip button down for a period of 6 seconds. The odometer will change to trip val[...]

CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required. 18. Brake System W arning Light This light illuminates when the ignition key is tur[...]

that the anti-lock portion of the brake system is not functioning and that service is requir ed. See your autho- rized dealer immediately . The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 20. Cargo Light The Cargo Lamp light will illuminate when the Car go Lamp is activated by pre[...]

24. W ater In Fuel Indicator Indicates there is water detected in the fuel filter . Refer to the Maintenance section, Drain- ing Fuel/W ater Separator Filter , for water drain procedur e. (See page 391 for more information.) 25. Low W asher Fluid Light This light comes on when the washer fluid level falls below approximately 1/4 full. The light wil[...]

30. Low Fuel W arning Light Glows when the pointer is between “E” and 1/8 indication mark (approximately 15% of tank vol- ume) on the fuel gauge. When the fuel gauge pointer is on “E” (equivalent to Distance T o Empty [DTE] = 0 on the overhead console if so equipped) ther e is reserve fuel capacity , which corresponds to appr oxi- mately 8%[...]

When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keep- ing is accurately maintained. On the RAQ radio the time button alternates the location of the time and frequency on the display . On the REF only one of the two, time or frequency is displayed at a time. Clock Setting Procedure 1. Press[...]

Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM r eception. They interfere very little with the fr equency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by suc[...]

SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rot[...]

Mode Button (Radio Mode) Press the mode button r epeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek d[...]

Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une/ Audio control. 3. After the hours are adjusted, press the right side T une/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side T une/Audio control. 5. T o exi[...]

Press the r otary TUNE control a fourth time and BAL will display . T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the r otary TUNE control a fifth time and F ADE will display . T urn the TUNE control to the left or right to adjust the sound level between the front and r ear speak- [...]

Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display . If the vol[...]

SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, [...]

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , cassette player , or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. The auxiliary mode becomes active when an electrical[...]

TIME Button (Auxiliary Mode) Press this button to change the display fr om elapsed playing time to time of day . The time of day will display for 5 seconds. R W/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button r epeatedly to select between the CD player and Satellite Ra[...]

SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERT AINMENT SYSTEMS (VES) CAP ABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radi[...]

Mode Button (Radio Mode) Press the mode button r epeatedly to select between the CD player , Satellite Radio, or V ehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button [...]

T ime Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une / Audio control. 3. After the hours are adjusted, press the right side T une / Audio control to set the minutes. The minutes will[...]

Press the r otary TUNE control a thir d time and TREBLE will display . T urn the TUNE control to the right or left to increase or decr ease the T reble tones. Press the r otary TUNE control a fourth time and BAL- ANCE will display . T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the[...]

Jazz Jazz News News Nostalgia Nostalgia Oldies Oldies Personality Personality Public Public Rhythm and Blues Rhythm_and_Blues Religious Music Religious_Music Religious T alk Religious_T alk Rock Rock Soft Soft Soft Rock Soft_Rock Soft Rhythm and Blues Soft_R_&_B Sports Sports T alk T alk T op 40 T op_40 W eather W eather By pressing the SEEK bu[...]

Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET/DIR button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM,12 FM and 12 Satellite (if equipped) stations to be stored into push-button me[...]

CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the d[...]

LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number wher e the CD is being loaded. The radio will display PLEASE W AIT and prompt when to INSER T DISC. After the radio displays ⬙ LOAD DISC ⬙ insert the CD into the player . Radio display will show ⬙ LO[...]

TIME Button (CD MODE for CD Audio Play) Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) b[...]

Notes On Playing MP3 Files The radio can play MP3 files, however , acceptable MP3 file recor ding media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc T ypes) The MP3 file recor ding media supported by the radio are CD-ROM, CD-R and CD-R W . Supported Medium Formats (File System[...]

Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and[...]

• Media - CD-R W media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with mor e files and folders T o increase the speed of disc loading, it is r ecommended to use CD-R media and single-session discs.[...]

If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not r emoved, the radio will continue to play the non-removed CD. If the CD is removed and ther e are other CD’s in the radio, the radio will play the next CD after a 2 minute timeout. If the CD is removed and ther e are no other CD’s in the [...]

T urn the TUNE control to display available folders or move through available folders. Pr ess the TUNE control to select a folder . Button s1-6( C D Mode for MP3 Play) Selects disc position s1-6f o r Play/Load/Eject. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual. Operating Ins[...]

Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) i[...]

Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une/ Audio control. 3. After the hours are adjusted, press the right side T une/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side T une/Audio control. 5. T o exi[...]

Press the r otary TUNE control a thir d time and TREBLE will display . T urn the TUNE control to the right or left to increase or decr ease the T reble tones. Press the r otary TUNE control a fourth time and BAL will display . T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the r ota[...]

Country Country Oldies Oldies Soft Soft Nostalgia Nostalgia Jazz Jazz Classical Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Soft_R_&_B Foreign Language Foreign_Language Religious Music Religious_Music Religious T alk Religious_T alk Personality Personality Public Public College College Unassigned W eather W eather By press[...]

Operating Instructions — T ape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatur es, the tape mechanism may requir e a few minutes to warm up for proper operation. Sometimes poor playb[...]

Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the featur e. Changing T ape Direction If you wish to change the direction of tape travel (side being played), press Pr eset 6. The lighted arrow in the display window will show the new direction. Metal T ape Selection If a standard met[...]

compact discs (CD-R W) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks and WMA. Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may eject a disc with the radio OFF . If you insert a disc with the ig[...]

Radio display will show ⬙ LOADING DISC ⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. LOAD/EJT - Eject Press the LOAD/EJT button and the push- button with the corresponding number wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTI[...]

RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. NOTE: MP3 and WMA Random Play are for file folders only . Press the SEEK button to move to the next rando[...]

The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and[...]

When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specifi- cation Sampling Fre- quency (kHz) Bit r[...]

T o increase the speed of disc loading, it is r ecommended to use CD-R media and single-session discs. T o create a single-session disc, enable the Disc at Once option before writing to the disc. Operation Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays [...]

radio, the radio will remain in CD mode and display ⬙ INSER T DISC” for 2 minutes. After 2 minutes, the radio will go to the previous tuner mode. INFO Button (CD Mode for MP3 Play) Press and INFO button while playing MP3 or WMA disc. The radio scrolls thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if a[...]

Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Phone” in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the “Satellite Radio” section of the Owner’s Manual. Operating Instructions - V ideo Entertainment System (VES) (If Equipped) Refer to separate “V [...]

menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability . Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America. Refer to your “Navigation User’s Manual” for detailed operating instruction[...]

System Activation NOTE: Y our vehicle’s radio must be on and in satellite mode when the activation process takes place. T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Ele[...]

ESN/SID Access W ith RAQ and RAK Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will display . The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed sinc[...]

Selecting a Channel Press and r elease the SEEK or TUNE knob to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and r elease the SCAN button (if equipped) to automatically change channel[...]

NOTE: Pressing the ⬙ SEEK ⬙ or ⬙ SCAN ⬙ button, while performing a music type scan, will change the channel by one and stop the search. Pr essing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button [...]

REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of the sw[...]

T ape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection. If you press the switch up or down twice it plays the sec[...]

5. A loose tape should be corrected befor e use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of [...]

NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. T ry a known good disc befor e considering disc player service. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance [...]

Heater Only — If Equipped The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows through [...]

Recirculation Modes (Panel or Bi-Level) Select the recir culation modes when the outside air contains smoke or odors. This feature allows for r ecircu- lation of interior air only . Air flows through the panel outlets in this mode. Air flows through the panel only or through both the panel and floor vents depending on the selected mode (panel vs bi[...]

Air Conditioning and Heating — If Equipped Air Conditioning Operation T o turn on the Air Conditioning, set the fan control at any speed and pr ess the snowflake button located at the right of the control panel. Conditioned air will be directed thr ough the outlets selected by the mode control. A light in the snowflake button shows that the air c[...]

NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Recirculation Modes (Panel or Bi-Level) Select the recir culation modes when the outside air contains smoke, odors, high humidity , or if rapid cooling is desi[...]

Blower Control The rotary knob on the left of the control panel is the blower contr ol. T urn the knob clockwise to one of the four positions to obtain the blower speed you desire. T o turn the blower off, turn the knob to the far left posi- tion. T emperature Control The rotary knob at the center of the control panel contr ols the temperature of t[...]

Air Conditioning with Dual Zone T emperature Control — If Equipped W ith the Dual Zone T emperature Contr ol System, each front seat occupant can independently contr ol the tem- perature of air coming fr om the outlets on their side of the vehicle. Air Conditioning and Heating Operation T o turn on the Air Conditioning, set the fan control at any[...]

Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recir culate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior . See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: [...]

Mix Outside air flows in equal proportions thr ough the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even i[...]

Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures. Circulatio[...]

conditioning system has been on. It is not an indication of a problem with the air conditioning system. Rear Air Duct—Mega Cab Only The rear seat will r eceive air flow in all modes except for Defrost. The rear air duct is designed to be pointed up when in A/C mode, and pointed down in Heat mode. Operating Tips Fast Cooldown For a fast cooldown, [...]

W indow Fogging W indows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the Air-conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature control, air direction and blower speed to maintain comfort.[...]

NOTE: On models equipped with Diesel engines, the idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to impr ove engine cooling. Y our air conditioning system is also equipped with an automatic recir culation system. When the system senses a heavy load or high heat conditions, it may use partial Recirculation A/C mo[...]

Operating Tips Chart UNDERST ANDING YOUR INSTRUMENT P ANEL 247 4[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es – Diesel Engines ......... 2 5 3 ▫ Manual T ransmission – If Equipped ........ 2 5 3 ▫ Automatic T ransmission – If Equipped ...... 2 5 3 ▫ Normal Starting Procedur e — Engine Manifold Airtemperature Above 66°F (19°C) ......... 2 5 4 ▫ Starting Procedur e — Engine Manifo[...]

䡵 Manual T ransmission .................... 2 7 4 ▫ Downshifting ........................ 2 7 5 䡵 Four-Wheel- Drive Operation — If Equipped . . . 276 ▫ Manually Shifted T ransfer Case Operating Information/Precautions ................ 2 7 6 ▫ Shifting Procedur e - Manually Shifted T ransfer Case .............................. 2 7 9 ▫ [...]

▫ Radial-Ply T ires ...................... 3 0 7 ▫ Compact Spare T ire — If Equipped ......... 3 0 8 ▫ Limited Use Spare — If Equipped ......... 3 0 9 ▫ T ire Spinning ........................ 3 0 9 ▫ T read W ear Indicators .................. 3 1 0 ▫ Life Of T ire ......................... 3 1 1 ▫ Replacement T ires .............[...]

䡵 T railer T owing ......................... 3 2 7 ▫ Common T owing Definitions ............. 3 2 7 ▫ T railer Hitch Classification ............... 3 3 1 ▫ T railer T owing W eights (Maximum T railer W eight Ratings) ...................... 3 3 2 ▫ T railer And T ongue W eight .............. 3 3 2 ▫ T owing Requirements .................[...]

ST ARTING PROCEDURES – DIESEL ENGINES The starter should not be operated for more than 15- second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating. W ARNING! Be sure to turn off the engine if you want to rest or sleep in your car . Accidents can be caused by inad- vertently moving the gear select[...]

The Cummins Diesel engine is equipped with several features designed to assist cold weather starting and operation: • The engine block heater is a resistance heater installed in the water jacket of the engine just above and behind the oil filter . It requir es a 1 10–1 15 volt AC electrical outlet with a grounded, thr ee-wire extension cor d. N[...]

CAUTION! If W A TER IN FUEL indicator light remains on DO NOT ST AR T engine before you drain water from the fuel filter to avoid engine damage. See Section 7 — Maintaining Y our V ehicle, for water drain proce- dures. 4. T urn the ignition key to ST AR T and crank the engine. Do not press the accelerator during starting. CAUTION! Do not crank en[...]

CAUTION! Do not crank engine for more than 15 seconds at a time or starter motor damage may result. T urn key to OFF and wait at least 2 minutes for starter to cool before repeating start procedure. • The W AIT TO ST ART light will r emain on for a period of time (length of time depends on engine tempera- ture). • After the W AIT TO ST ART ligh[...]

attempting to start the engine. This can be accomplished by turning the ignition OFF for at least 5 seconds and then back ON after the W AIT TO ST ART light has gone off, but befor e the engine is started. However , repeated cycling of the manifold heaters will result in damage to the heater elements or reduced battery voltage. NOTE: If multiple pr[...]

NOTE: When a diesel engine is allowed to run out of fuel or the fuel gels at low temperatures, air is pulled into the fuel system. Y ou may try priming as described below . 1. Add a substantial quantity of fuel to the tank (5 to 10 gallons) or eliminate the gelled fuel condition. 2. Crank the engine for 1 to 2 seconds. If the engine does not start,[...]

Starting Fluids W ARNING! ST AR TING FLUIDS or flammable liquids are NEVER TO BE USED in the Cummins Diesel (see W arning label). Never pour diesel fuel, flammable liquid, starting fluids (ether) into the air cleaner canister , air intake piping, or turbocharger inlet in an attempt to start the vehicle. This could result in a flash fire and explosi[...]

• V oltmeter Operation: • The voltmeter may show a gauge fluctuation if certain engine temperatures ar e below 66°F (19°C). This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the cycling operation is controlled by the engine contr ol mod- ule, this time will not[...]

NOTE: • Use of Climatized Diesel Fuel or Number 1 Diesel Fuel results in a noticeable decr ease in fuel economy . • Climatized Diesel Fuel is a blend of Number 2 and Number 1 Diesel Fuels which reduces the temperatur e at which wax crystals form in fuel. NOTE: Refer to Fuel Requirements in this section for further details on fuel recommendation[...]

Block Heater Usage A. T emperatures below 0°F (-18°C) • Block Heater Required for 15W -40 • Block Heater Recommended for 5W -40 B. T emperatures below - 20°F (-29°C) • Block Heater Required for 5W -40 W inter Front Usage If a winter front or cold weather cover is to be used, a percentage of the total grille opening ar ea must be left unco[...]

Engine W arm-Up A void full throttle operation when the engine is cold. When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressur e to stabilize as the engine warms up. NOTE: High-speed, no-load running of a cold engine can result in excessive white smoke and poor engine performance. No-load engine speeds s[...]

speed will slowly increase to 1000 RPM after 2 minutes of idle, if the following conditions are met: • foot is off brake pedal and thr ottle pedal • automatic transmission is in Park (P) • vehicle speed is zero • Applying the throttle will cancel fast idle • If the engine is equipped with an aftermarket exhaust brake (manual transmissions[...]

Driving Condition Load T urbo- charger T emperature Idle T ime (min.) Before Engine Shutdown Stop and Go Empty Cool Less than One Stop and Go Medium One Highway Speeds Medium W arm T wo City T raffic Maximum GCWR Three Highway Speeds Maximum GCWR Four Uphill Grade Maximum GCWR Hot Five Engine Speed Control CAUTION! Prevent overspeeding the engine g[...]

A void Low Coolant T emperature Operation Continual operation at low coolant temperature below the normal range on the gauge (140°F/60°C) can be harmful to the engine. Low coolant temperature can cause incomplete combustion which allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcas[...]

CAUTION! If oil pressure falls to less than normal readings, shut the engine off immediately . Failure to do so could result in immediate and severe engine damage. Do Not Operate The Engine W ith Failed Parts Practically all failures give some warning befor e the parts fail. Be on the alert for changes in performance, sounds, and visual evidence th[...]

Gear Ranges DO NOT race the engine when shifting from Park or Neutral position into another gear range. “P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Alw[...]

W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idlin[...]

“1” First Use this position for driving up very steep hills and for engine braking at low speeds 20 mph (32 km/h) or less when going downhill. T o prevent excessive engine speed, do not exceed 25 mph (40 km/h) in this range. NOTE: Use caution when operating a heavily loaded vehicle in “2” Second or “1” First gear selections in high ambi[...]

NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Over drive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperatur e has risen to a suitable level. Refer also to the Note under torque converter c[...]

reduce the potential for transmission over heating or failure due to excessive shifting. When operating in “TOW HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) ar e allowed during steady cruise (for improved fuel economy) and automatic closed- throttle downshifts to 3r[...]

the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal. Pressing the “T OW/HAUL” button, when the transmis- sion is sufficiently warm, will demonstrate that the transmission is able to shift into and out of overdrive. NOTE: If the ve[...]

The alarm will continue for 3 minutes if the driver’s door is closed but none of the other conditions listed above are met. MANUAL TRANSMISSION W ARNING! Y ou or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the veh[...]

toward you in one motion. Do not pull the lever sharply left as you may shift accidentally into 2nd gear and damage the transmission. Y ou should use 1st gear when starting from a standing position if under heavy load or when pulling a trailer . T o shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear [...]

T o prevent clutch and transmission damage, your vehicle should be downshifted at speeds no greater than those listed in the Maximum Recommended Downshifting Speed chart. Maximum Recommended Downshifting Speeds Gear Selec- tion 1st 2nd 3rd 4th 5th Maxi- mum Speed 10 mph (16 km/h) 19 mph (31 km/h) 32 mph (51 km/h) 50 mph (80 km/h) 68 mph (109 km/h) [...]

The 4-wheel-drive light (4WD), located in the instrument cluster , alerts the driver that the vehicle is in 4-wheel drive and that the front and r ear driveshafts are locked together . This light illuminates when the transfer case is shifted to either the 4H or 4L positions. There is no light for the 2H or N (Neutral) positions. When operating your[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission p[...]

Shifting Procedure - Manually Shifted T ransfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). W ith the vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after co[...]

NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur . The pre- ferred method is with the vehicle r olling 2 to 3 mph (3 to 5 km/h). A void [...]

This Electronically Shifted transfer case pr ovides 4 mode positions: 2 (rear) wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral. The Electronically Shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) for normal street and highway conditions (dry har d surfaced roads). When additio[...]

T ransfer Case Position Indicator Lights — Electronically Shifted T ransfer Case Only T ransfer case position indicator lights are located in the instrument cluster and indicate the curr ent and desired transfer case selection. When you select a differ ent trans- fer case position, the indicator lights will do the follow- ing: If All Shift Condit[...]

W ARNING! Always engage the parking brake when powering down the vehicle if the ⴖ Service 4WD ⴖ light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury . NOTE: Do not attempt to make a shift while only the front or r ear wheels are spinning. The transfer case is not equipped with a sync[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission p[...]

Shifting Procedure - Electronically Shifted T ransfer Case NOTE: If any of the requir ements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requir ements for th[...]

key must be in the ON position with the engine either RUNNING or OFF . This shift cannot be completed if the key is in the accessory position. NOTE: The 4x4 system will not allow shifts between 2WD/4HI if the front and/or r ear wheels are spinning (no traction). In this situation the selected position indi- cator light will flash and the original p[...]

3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2 of either the Preferr ed or Alternate Procedur e are not satisfied prior to attempting the shift then the desired po[...]

W ARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground, since the vehicle may drive through the rear wheel remaining on the ground. Y ou could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels ar e on a slippery surface. This coul[...]

DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns slowly and cautiously . If you must back down a hill, bac[...]

P ARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster r ed brake warning light will come on and flash to indicate that the parking brake is applied. Y ou must be sure that the parking brake i[...]

W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or First gear . Failure to do so may allow the vehicle to roll and cause damage or injury . • Never leave children alone in a vehic[...]

Brake Noise During normal operation of the brake system certain noises may be present fr om time to time. Occasional ⬙ groan ⬙ or ⬙ squeal ⬙ noises may occur during normal operation of the brake system which may not be indica- tive of a problem. These noises may be hear d at any time the brakes are applied but may be mor e noticeable during[...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

ABS W arning Light The Anti-lock Brake System includes an amber warning light, located in the instrument cluster . When the light is illuminated, the Anti-lock Brake System is not function- ing. The system reverts to standar d non-anti-lock brakes. W ARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accide[...]

W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the po[...]

• European Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tir e size designation. Example: 215/65R15 96H • L T (Light T ruck)-Metric tire sizing is based on U.S. design standards. T[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Millimeters (mm) 65 = [...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be [...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If th[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the[...]

3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size, and[...]

passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle[...]

ST ARTING AND OPERA TING 303 5[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory [...]

2. Economy— Improper inflation pr essures can cause uneven wear pat- terns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation, also increases tire r olling resistance and r esults in higher fuel consumption. 3. Ride Comfort and V ehicle Stabili[...]

CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.” Cold tir e inflation pressure is defined as[...]

loading may be requir ed for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pr essures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could[...]

Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity . W ARNING! T emporary use spare tires are for emerg[...]

Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tir e warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the fr ont or rear axle of your vehicle, but it is not. Inst[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter w[...]

Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose con[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle. This can cause unpredictable handling and stress to steering[...]

Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . SUPPLEMENT AL TIRE PRESSURE INFORMA TION – IF EQUIPPED A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs[...]

These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es of Ram 4X2 trucks. NOTE: The use of class “U” chains is permitted on the front and r ear of 4X4, 2500 Ram T rucks with L T245/ 70R17E tires. NOTE: The use of class “U” chains is permitted on th[...]

SNOW TIRES Snow tires should be of the same size and type constr uc- tion as the front tir es. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requir ement associated with the tire. These tir es should always be operated at the vehicle maximum capacity inflation pressur es under any load condition. While studded tir[...]

NOTE: On Canadian vehicles only , if your Ram truck is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the r ear , do not use a front to back r otation pattern. Instead, rotate your tir es side to side at the recommended intervals. Dual Rear Wheels The tires used on dual wheel assemblies should be matched for [...]

CAUTION! 3500 Dual Rear T ires have only one approved direc- tion of rotation. This is to accommodate the asym- metrical design (tread pattern) of the ON/OFF road tire and the use of Outline White Letter (OWL) tires. • When replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the co[...]

FUEL REQUIREMENTS (DIESEL ENGINES) Use good quality diesel fuel from a r eputable supplier in your Dodge truck. For most year -round service, No. 2 diesel fuel meeting ASTM specification D-975 will pr o- vide good performance. If the vehicle is exposed to extreme cold (below 20°F or -7°C), or is r equired to operate at colder-than-normal conditio[...]

NOTE: A maximum blend of 5% biodiesel may be used with your Cummins Diesel equipped Dodge Ram T ruck. NOTE: In addition, commercially available fuel addi- tives are not necessary for the pr oper operation of your Cummins Diesel equipped Dodge Ram T ruck. NOTE: No. 1 diesel fuel should only be used where extended arctic conditions (-10°F or -23°C)[...]

Fuel Properties - No. 1 - Diesel Reference Carbon Residue - Less than.15% (Ramsbottom ASTM D-524 Flash Point - 100°F min. (ASTM D-93) Density - 40-34 API gravity (ASTM D-287) Cloud Point - (- 30F°) (ASTM D-97) Active Sulfur (ASTM D-130) Copper Strip Corrosion - #3 rating ADDING FUEL (DIESEL ENGINES) CAUTION! T o avoid fuel spillage and overfillin[...]

Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door . If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the[...]

Bulk Fuel Storage If you store quantities of fuel, good maintenance of the stored fuel is also essential. Fuel contaminated with water will promote the gr owth of “microbes.” These microbes form “slime” that will clog fuel filters and lines. Drain condensation from the supply tank and change the line filter on a regular basis. NOTE: When a [...]

4. Repeat the procedure if the engine does not start. CAUTION! Do not engage the starter motor for more than 15 seconds at a time. Allow two minutes between the cranking intervals. NOTE: The engine may run r ough until the air is forced from all the fuel lines. VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Adm[...]

Gross Axle W eight Rating (GA WR) The GA WR is the maximum permissible load on the front and rear axles. The load must be distributed in the car go area so that the GA WR of each axle is not exceeded. Each axle GA WR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles [...]

then be determined separately to be sure that the load is properly distributed over fr ont and rear axle. W eighing the vehicle may show that the GA WR of either the front or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from fr ont to rear or r ear to front as appropriate until the spec[...]

NOTE: The weights shown in this chart are not necessarily the weights for your vehicle. Also, the amount of load added to both the front and rear axles can be computed after the vehicle has been weighed both in its ⴖ curb weight ⴖ condition, and in its ⴖ loaded and ready for operation ⴖ condition. Gross V ehicle W eight Rating (GVWR) 6500 L[...]

TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible. T o maintain warranty coverage, follow the requir ements and recommendations in this ma[...]

Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and r ear axles. Distribute the load over the front and r ear axles evenly . Make sure that you do not exceed either front or rear GA WR. W ARNING! It is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if eithe[...]

W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They ar e typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axel(s). When used in accordance with the manufactur ers’ directions, it provides for a mor e level ride,[...]

Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the tr uck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. W eight Distributing Hitch System Improper Adjustment of W eight Distributing System 330 ST ARTING AND OPERA TING[...]

Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the tr uck bed. T railer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alteratio[...]

T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .dodge.com/towing . • http:// www .dodge.ca (Canada). T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the front o[...]

• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your v[...]

W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou[...]

2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requir ement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tir e inflation pressur e[...]

actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electr onic brake controller is not r equired. − T railer brakes are r ecommended for trailers over 1,000 lbs (454 kg) and requir ed for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it s[...]

NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector ST ARTING AND OPERA TING 337 5[...]

T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. Ho[...]

− When using the speed control, if you experience speed drops gr eater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency . T owing T ips — Cooling System T o reduce potential for engine and transmission over - heating, take the follow[...]

Blindspot Mirror T railer T owing Position 340 ST ARTING AND OPERA TING[...]

SNOWPLOW Snowplow Prep Packages ar e available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow . NOTE: Before installation of a snowplow it is highly recommended that the owner / installer obtain and follow the recommendations contained within the cur - rent Dodge BODY BUILDER’S GUI[...]

Before plowing • Check the hydraulic system for leaks and proper fluid level. • Check the mounting bolts and nuts for proper tight- ness. • Check the runners and cutting edge for excessive wear . The cutting edge should be 1/4 to 1/2 inch above ground in snow plowing position. • Check that snowplow lighting is connected and func- tioning pr[...]

of the plow . Front end tow-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tir e wear . The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equip- ment following the recommendations pr ovided by the specific snowplow ma[...]

NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside tempera- ture display will show higher temperatur es than the outside ambient temperature. The higher displayed tem- perature is due to blocked or r educed airflow to the underhood ambient temperatur e sensor by the snow- plow . This is common and outside [...]

RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational T owing – 2 Wheel Drive Models Recreational towing 2 Wheel Drive is not allowed. T owing with the rear wheels on the gr ound can result in severe transmission damage. Recreational T owing – 4 Wheel Drive Models CAUTION! Failure to follow these requirements can cause se- vere damage to t[...]

CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (NEUTRAL) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Depress the brake pedal. 4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual trans[...]

CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P (P ARK) with the transfer case in N (NEUTRAL) and the engine RUN- NING. W ith the transfer case in N (NEUTRAL) ensure that the engine is OFF prior to shifting the transmission into P (P ARK) Returning to Normal Operation — Manual Shift T ransfer Case Use[...]

CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. Recreational T owing Procedure — Electronic Shift T ransfer Case — If Equipped Use the following procedur e to pre[...]

6. Using the point of a ballpoint pen or similar object, depress the r ecessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is[...]

NOTE: Flashing neutral (N) position indicator light indicates that shift requir ements have not been met. CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. W ith the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting th[...]

NOTE: Items 1 through 5 ar e requir ements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until 1 second elapses and the shift has been completed. If any of these requir ements (with the exception of 3 - key ON) are not met prior to depressing the Neutral (N) button or ar e no longer met during th[...]

CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. 352 ST ARTING AND OPERA TING[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 3 5 4 䡵 Jacking And T ire Changing ................ 3 5 5 ▫ All Models .......................... 3 5 5 䡵 Jacking Instructions ..................... 3 5 6 ▫ Removing The Spare T ire ................ 3 5 6 ▫ T ire Changing Procedur e ................ 3 5 7 [...]

HAZARD W ARNING FLASHER The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column. When the Hazard W arning switch is activated, all directional turn signals will flash off and on to warn oncoming traf fic of an em[...]

JACKING AND TIRE CHANGING W ARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a ser[...]

W ARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience, abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury . JACKING INSTRUCTIONS Removing The Spare [...]

NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of y[...]

• T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. Instructions W ARNING! Carefully follow these tire[...]

1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack [...]

4X2 Jacking 360 WHA T TO DO IN EMERGENCIES[...]

4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wh[...]

(SR W) models and 145 ft. lbs. (197 N·m) for 3500 dual rear wheel models. If in doubt about the correct tightness, have them checked with a torque wr ench by your dealer or at a service station. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra ti[...]

ratchet firmly . The hub cap should pop off. The wheel skins can now be removed. For the fr ont hub cap on 3500 models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be r emoved. CAUTION! Use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the h[...]

8-Stud — Dual Rear Wheels Dual wheels are flat mounted, center piloted. The lug nuts are a two piece assembly . When the tires ar e being rotated or r eplaced, clean these lug nuts and add 2 drops of oil at the interface between the hex and the washer . Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these [...]

These dual rear wheels should be tightened as follows: 1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go thr ough the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and [...]

wheel. The nuts should then be tightened to recom- mended torque. T ighten the nuts to final torque in increments. Pr ogress ar ound the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended tor ques are shown in the following chart. Disc Wheels T ype Nut Stud Size T orque Ft. Lbs.[...]

JUMP-ST ARTING W ARNING! T o prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other . Keep open flames or sparks away from battery vent holes. Always wear eye protection when work- ing with batterie[...]

CAUTION! Use the Jump Start Procedure only when the charge indicator (if equipped) in both batteries is dark in the center . Do not attempt jump starting when either battery charge indicator (if equipped) is bright or yellow . If charge indicator (if equipped) has a green dot in the center , failure to start is not due to a discharged battery and c[...]

2. Connect one end of the other jumper cable to negative (-) post of booster battery . Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery . Make sure a good connection is made, free of dirt and gr ease. W ARNING! • Do not connect the cable to the negative post of the discharge[...]

W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. With Portable Starting Unit There ar e many types of these units available. Foll[...]

not freeing the vehicle, may lead to transmission over - heating and failure. Allow the engine to idle with the transmission selector in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and r educe the risk of transmis- sion failure during pr olonged efforts to fr ee a stuck vehicle. EMERGENCY T[...]

CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. Y ou could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to pr event damage to your vehicle. Use only tow bars and other equipment designed for the purp[...]

2–Wheel- Drive V ehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF position along with the front wheels raised and the r ear wheels on the ground. Speed must not exceed 30 mph (50 km/h) and distance must not exceed 15 miles (25 km). CAUTION! T owing faster than 30 mph (50 km/h[...]

[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment .................... 3 7 8 ▫ 5.9L HO Cummins T urbo Diesel ........... 3 7 8 䡵 Onboard Diagnostic System (OBD II) ......... 3 7 9 䡵 Replacement Parts ...................... 3 7 9 䡵 Engine Data Plate ...................... 3 8 0 䡵 Dealer Service ......................... 3 8 0 䡵 S[...]

▫ Front Axle Universal Drive Joints And Pivot Bearings ............................ 3 9 8 ▫ Body Lubrication ..................... 3 9 9 ▫ W indshield W iper Blades ................ 3 9 9 ▫ W indshield W ashers ................... 3 9 9 ▫ Exhaust System ...................... 4 0 0 ▫ Cooling System ....................... 4 0 1 ▫ F a [...]

䡵 Bulb Replacement ...................... 4 3 3 ▫ Headlight (Halogen)/Front Park And T urn Lights ...................... 4 3 3 ▫ Fog Lights .......................... 4 3 6 ▫ T ail, Stop, T urn And Backup Lights ......... 4 3 7 ▫ Center High-Mounted Stoplight (CHMSL) W ith Cargo Light ......................... 4 4 0 ▫ Cab T op Clearance[...]

ENGINE COMP ARTMENT 5.9L HO CUMMINS TURBO DIESEL 378 MAINT AINING YOUR VEHICLE[...]

ONBOARD DIAGNOSTIC SYSTEM (OBD II) V ehicles equipped with California emissions controls have a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating pr operly , your vehicle will provide excellent performance [...]

ENGINE DA T A PLA TE Use the information from the engine data plate when discussing service or sourcing parts for your engine. The engine data plate is located on the intake side of the breather cover . DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner [...]

CAUTION! T o maintain your vehicle safely follow these guide- lines: • W atch your vehicle’s mileage and check your Mainte- nance Schedules regularly for r equired servicing. Ex- cessive wear or damage to certain vehicle components can result if r equired services ar e not performed. • If you have your vehicle undercoated, inspect for underco[...]

• If an engine has been operating and the coolant is hot, allow the engine to cool before you slowly loosen the filler cap and relieve the pr essure fr om the cooling system. • T o avoid burns, remember that the engine components will stay hot after the engine is shut off. • Do not use gasoline or other flammable materials to clean parts. Alw[...]

MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there ar e other items that should operate satisfactorily without periodic maintenance. However , if a malfunction of these item[...]

Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Frequent short trips wher e the engine does not achieve full operati[...]

If ANY of these apply to you, then change your engine oil at every interval shown in schedule ⬙ B ⬙ of the ⬙ Mainte- nance Schedules ⬙ section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙ A ⬙ of the ⬙ Mainte- nance Schedules ⬙ section of this manual. NOTE: Most vehi[...]

Y ou may use synthetic engine oils provided the r ecom- mended oil quality requir ements are met, and the r ecom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacture str ongly recommends against the addi- tion of any additives (other than leak detection dyes or lube odorants) to the en[...]

Always check the condition of the used oil. This can give you an indication of some engine problems that might exist. • Thin, black oil indicates fuel dilution. • Milky discoloration indicates coolant dilution. Clean the area ar ound the oil filter base. Remove the filter from the underside of the vehicle using a cap style oil filter wrench. Cl[...]

CAUTION! Overtightening may distort the threads or damage the filter element seal. Install the filter as specified by the filter manufacturer . T urn the filter 3/4 to one full turn after making contact with the gasket. Check the condition of the threads and sealing surface on the oil pan and drain plug. Install the drain plug and sealing washer an[...]

Disposing Of Used Engine Oil And Filter Care should be taken in disposing of the used engine fluids from your vehicle. Used fluids, indiscriminately discarded, can pr esent a problem to the envir onment. Contact your local dealer , service station, or governmen- tal agency for advice on recycling pr ograms and where used fluids and filters can be s[...]

Do not remove the top of the air filter housing to inspect the filter element on your diesel engine under normal operating conditions. The clear plastic housing on the Filter Minder™ allows you to view the amount of air pressur e drop acr oss the filter element. It consists of a diaphragm and a calibrated spring sealed inside the plastic housing.[...]

A visual inspection of the air cleaner filter element is never recommended under normal cir cumstances. A badly restricted element may appear clean while a soiled element may be quite effective in filtering particles without restricting air flow . Rely on the Filter Minder™ to determine when a filter change is necessary . After a new filter eleme[...]

CAUTION! Do not drain the fuel/water separator filter when the engine is running. NOTE: Care should be taken in disposing of used fluids from your vehicle. Used fluids, indiscriminately dis- carded, can pr esent a problem to the envir onment. Con- tact your local authorized dealer , service station, or government agency for advice on recycling pr o[...]

Priming if the engine has run out of fuel 1. Add a substantial quantity of fuel to the tank 5 to 10 gallons (19L to 38L). 2. Crank the engine for 1 to 2 seconds. If the engine does not start, then release the key or starter button back to the RUN position (do not turn the key back to the OFF position). The electric fuel transfer pump will continue [...]

W ARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. CAUTION! Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system. NOTE: A maximum blend of 5% biodiesel may be used with your[...]

W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water . • Battery gas is flammable and explosive. Ke[...]

Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decr eases to 0°F (-18°). For the same de- crease in temperatur e, the engine requir es twice as much power to crank at the same RPM. The use of 120 V AC powered battery blankets will gr eatly increase starting capability at low temperatures. Suitable batte[...]

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and r ecycling equ[...]

Steering Linkage — Inspection Whenever the vehicle is hoisted, all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be r eplaced to prevent leakage or contamination of the grease. Front Prop Shaft Lubrication Lubricate the front driveshaft gr ease fitting at each oil change listed in the appro[...]

Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against r ust and wear . Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubric[...]

When refilling the washer fluid r eservoir , take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. T o prevent fr eeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate. This rating inform[...]

inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as requir ed. W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, fol- low the preceding safety tips[...]

accumulation of bugs, leaves, etc. If dirty , clean by gently spraying water from a gar den hose vertically down the face of the condenser . Check the coolant recovery bottle tubing for brittle r ub- ber , cracking, tears, cuts and tightness of the connection at the bottle and radiator . Inspect the entire system for leaks. Extremely cold ambient t[...]

W ARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine! The coolant is under pres- sure and severe scalding could result. Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refille[...]

CAUTION! Mixing of coolants other than specified HOA T en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOA T cool- ant is introduced into the cooling system in an emergency , it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolan[...]

The use of lower quality water will reduce the amount of corrosion pr otection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of pr otection against freezing ac- cording to the temperatur es occurring in the area wher e the vehicle is operated. NOTE: Mixing coolant types will decreas[...]

Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring pr oper disposal. Check with your local authorities to determine the disposal rules for your community . Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. Pr event ingestion [...]

• Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifr eeze needs to be added, contents of coolant recovery bottle must also be protected against fr eezing. • If frequent coolant additions ar e requir ed, or if the level in the coolant recovery bottle does not [...]

Charge Air Cooler (Inter-Cooler) The charge air cooler is positioned between the radiator and the air conditioner condenser . Air enters the engine through the air cleaner and passes thr ough the turbo- charger wher e it is pressurized. This pr essurized air rapidly reaches high temperatur e. The air is then directed through a hose to the char ge a[...]

Brake System Power Disc Brakes (Front and Rear) Disc brakes do not requir e adjustment; however , several hard stops during the br eak-in period are r ecommended to seat the linings and wear off any for eign material. Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- at[...]

W ith disc brakes the fluid level can be expected to fall as the brake linings wear . However , an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Refer to Fluids, Lubricants and Genuine Parts for the correct Fluid type. W ARNING! Use of a brake fluid that may have a lower initial boiling point, or uni[...]

Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hy- draulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuf fing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with poss[...]

with water or subjected to severe service, follow the recommended change intervals in Maintenance Schedule “B” in Section 8 of this manual. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. NOTE: The presence of water in the gear lubricant will result in corr osion and possible failure of dif fere[...]

Lubricant Selection for 6-Speed Manual T ransmission — If Equipped If it becomes necessary to add fluid or change the fluid, be sure to use the same lubricant or equivalent. Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. Automatic T ransmission Fluid Level Check The fluid level should be checked when the engine is f[...]

b. If the fluid is warm, the reading should be between the two holes. If the fluid level indicates low , add sufficient fluid to bring to the pr oper level. Fluid is added through the dipstick tube. NOTE: T o prevent dirt and water fr om entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly s[...]

It is important that proper lubricant is used in the transmission. Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. A band adjustment and filter change should be made at the time of the oil change. The fluid and filter(s) should be changed and the bands adjusted (if equipped) ) as specified in the Maintenance Schedule ([...]

• If a bearing assembly is accidentally separated when servicing the brake rotors, it should be r eplaced. Rear Wheel Bearings Clean and repack when brake linings ar e replaced or rotors r esurfaced. Selection Of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owne[...]

Noise Control System Required Maintenance & W arranty For 3500 T wo-Wheel Drive and Four-Wheel Drive mod- els over 10,000 lbs. (4 535 kg) Gross V ehicle W eight Rating. All vehicles built over 10,000 lbs. (4 535 kg) Gross V ehicle W eight Rating and manufactured for sale and use in the United States are r equired to comply with the Federal Gove[...]

or suspected. Proper maintenance of the entir e vehicle will help the effectiveness of the noise contr ol systems. Exhaust System Inspect the entire exhaust system for leaks and damaged parts. Devices such as hangers, clamps, and U-bolts should be tight and in good condition. Damaged compo- nents, burned or blown out mufflers, burned or r usted out[...]

• EXHAUST SYSTEM − Removal or rendering inoperative exhaust system components including the muffler or tailpipe. • ENGINE COOLING SYSTEM − Removal or rendering inoperative the fan clutch. − Removal of the fan shroud. Noise Emission W arranty The manufacturer warrants that this vehicle as manufac- tured by the manufactur er , was designed,[...]

Maintenance Log and Service Chart — 24 V alve Cummins T urbo Diesel Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed. MILES 7,500 15,000 22,500 30,000 37,500 45,000 52,500 60,000 KILOMETERS 12 000 24 000 36 000 48 000 60 000 72 000 84 000 96 00[...]

Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed. MILES 67,500 75,000 82,500 90,000 97,500 84,000 105,00 1 12,500 KILOMETERS 108 000 120 000 132 000 144 000 126 000 156 000 168 000 181 000 Exhaust system- inspect Air cleaner assembly-inspect ODOM[...]

Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and r oad surfaces during other seasons, are highly corrosive to the metal in your vehi[...]

• Use Mopar Cleaner W ax to remove r oad film, stains and to protect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will [...]

• Use Mopar touch up paint on scratches as soon as possible. Y our dealer has touch up paint to match the color of your vehicle. Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion. T o remove heavy soil, use Mopar Wheel Cl[...]

W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household- type glass cleaner . Never use an abrasive type cleaner . Use caution [...]

Replace the belts if they appear frayed or worn or if the buckles do not work properly . Dry with a soft tissue. FUSES (INTEGRA TED POWER MODULE) An integrated Power Module is located in the engine compartment near the battery . This center contains car- tridge fuses and mini fuses. A description of each fuse and component may be stamped on the ins[...]

Cavity Cartridge Fuse Mini Fuse Description 1 20 Amp Y ellow Power Outlet Console 2 20 Amp Y ellow Cabin Compartment Node (CCN) Door Locks/Brake T rans- mission Shift Inter- lock (BTSI) 3 20 Amp Y ellow Spare 4 20 Amp Y ellow Spare 5 20 Amp Y ellow Power Sunroof 6 10 Amp Red Occupant Classifica- tion Module (OCM)/ VIST Fan/W astegate Cavity Cartrid[...]

Cavity Cartridge Fuse Mini Fuse Description 1 1 20 Amp Y ellow Ignition Off Draw (IOD)-Cabin Com- partment Node (CCN)/Radio/Under Hood Lamp/W ireless Control Module (WCM)/Satellite Digi- tal Audio Receiver (SDARS)/Hands Free Module (HFM) 12 30 Amp Pink Electric Brake 13 25 Amp Natural Power-Battery R W AL/ABS Module Feed 14 15 Amp Blue Park Lamps L[...]

Cavity Cartridge Fuse Mini Fuse Description 23 10 Amp Red Engine Control Mod- ule (ECM)/W ireless Control Module (WCM)/HVC 24 20 Amp Blue Subwoofer Amplifier (SR T -10 Only) 25 10 Amp Red Power Mirror 26 20 Amp Y ellow Brake Switch/Center High Mount Stop Lamp (CHMSL) 27 40 Amp Green Power Seats 28 10 Amp Red Power Run/Start- NCC/W ireless Con- trol[...]

Cavity Cartridge Fuse Mini Fuse Description 36 25 Amp Natural Audio_Amplifier 37 15 Amp Blue Spare 38 20 Amp Y ellow Power Outlet IP 39 10 Amp Red Sunroof/Seatbelt T en- sioner 40 20 Amp Y ellow Cigar Lighter 41 25 Amp Natural Spare 42 30 Amp Pink Diesel PCM (Diesel Only) CAUTION! • When installing the Integrated Power Module cover , it is import[...]

VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Integrated Power Module, located in the engine compartment. The I.O.D. cavity includes a snap-in retainer t[...]

REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights ............... T S 212-2 Dome Light ............................ 7679 All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not appr oved. LIGHT BULBS — Outside Bulb No. Back-Up .............................. 3057 Center High Mounted Stop Lam[...]

BULB REPLACEMENT Headlight (Halogen)/Front Park and T urn Lights CAUTION! This is a halogen bulb. A void touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two (2) bolts from the front of the head- light housing. Front Headlight Housing Bolts MAINT AINING YOUR VEHICLE 433 7[...]

3. Remove the plug from the inner fender well and remove the nut thr ough the access hole. 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors. Inner Fender Plug Rear Headlight Housing Nut Access 434 MAINT AINING YOUR VEHICLE[...]

NOTE: For easier removal, pull the headlight assembly straight forward, applying the gr eatest amount of force to the outer edge of the headlight assembly . 5. Unlock and pull connector straight from the base of the headlight halogen bulb. 6. T wist connector on the side marker/turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb [...]

7. Remove housing from vehicle with headlight halogen bulb in housing. 8. T wist the headlight halogen bulb 1 ⁄ 4 turn and remove headlight bulb from the housing. 9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 10. Reverse procedure for installation of bulbs and hous- ing. Fog Lights 1. Re[...]

2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing. T ail, Stop, T urn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. Removing the T wo (2) Screws MAINT AINING YOUR VEHICLE 437 7[...]

2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged. 3. Rotate the bulb socket counter clockwise to remove from the housing. Pulling Housing From Body Rotating Bulb Socket From Housing 438 MAINT AINING YOUR VEHICLE[...]

4. Pull bulb straight out of socket. 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body . Pulling Bulb From Socket Sliding Raised Blocks Past Body MAINT AINING YOUR VEHICLE 439 7[...]

Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body . 440 MAINT AINING YOUR VEHICLE[...]

3. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. Cab T op Clearance Lights — If Equipped 1. Remove the two screws from the top of[...]

2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly . 3. Pull the bulb straight from it’s socket and replace. 442 MAINT AINING YOUR VEHICLE[...]

T ailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the r ear . 2. T urn socket 1 ⁄ 4 turn counterclockwise to access the bulb. MAINT AINING YOUR VEHICLE 443 7[...]

3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. Rear Light Bar ID Marker (Dual Rear Wheel) – If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. T urn the socket 1/4 turn counterclockwise to access the bulb. 444 MAINT AINING YOUR VEHICLE[...]

3. Pull the bulb straight out from the socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly . 2. Pull the entire assembly from the fender . 3. T urn socket 1 ⁄ 4 turn counterclockwise and r emove from assembly to access the bulb. 4. Pull bulb[...]

FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifr eeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil For the proper quality and SAE Grade oil for your engine, r efer to the section ⬙ Maintenance Procedur es. ⬙[...]

Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar 威 A TF+4, Automatic T ransmission Fluid. T ransfer Case Mopar 威 A TF+4, Automatic T ransmission Fluid. Manual T ransmission Fluid G-56 Mopar 威 A TF+4, Automatic T ransmission Fluid. Clutch Linkage Multipurpose Grease, NLGI Grade 2 E.P . or equivalent. Front [...]

[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 4 5 0 䡵 Maintenance Schedules — 5.9L Cummins T urbo Diesel ............................... 4 5 0 ▫ Schedule “B” ........................ 4 5 3 ▫ Schedule “A” ........................ 4 6 3 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best ve[...]

• Off-r oad or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% thr ottle). NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙ B ⬙ . NOTE: If ANY of these apply to you then change your coolant every 101,250 miles (162 000 km) or 60 months, whichever co[...]

Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , and transmission and transfer case (if equipped), add as needed. • Check Filter Minder™. Replace air cleaner filter ele[...]

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Frequent short trips wher e the engine does not achieve full operating temperature (operating temperatur e de- fined as 190° F (66° C ) coolant temperature). • Extensive engine idling (over 10 minutes per hour of opera[...]

Miles 3,750 7,500 1 1,250 15,000 18,750 (Kilometers) (6 000) (12 000) (18 000) (24 000) (30 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX Lubricate outer tie rod ends 2500/3500 (4X4) mod- els. XX Replac[...]

Miles 22,500 26,250 30,000 33,750 37,500 (Kilometers) (36 000) (42 000) (48 000) (54 000) (60 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage. XX X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els. X[...]

Miles 41,250 45,000 48,750 52,500 56,250 (Kilometers) (66 000) (72 000) (78 000) (84 000) (90 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4) models. X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX Lubricate outer tie rod ends 2500/3500 (4X4). X X Inspe[...]

Miles 60,000 63,750 67,500 71,250 75,000 (Kilometers) (96 000) (102 000) (108 000) (1 14 000) (120 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXX Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). X Rotate tires. X X X Check spare tir e fo[...]

Miles 60,000 63,750 67,500 71,250 75,000 (Kilometers) (96 000) (102 000) (108 000) (1 14 000) (120 000) Change 6-spd manual transmission (G-56) fluid 2500/3500. X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X X Drain and refill transfer case fluid (4X4). X Drain and refill automatic transmission fluid and change main [...]

Miles 78,750 82,500 86,250 90,000 93,750 (Kilometers) (126 000) (132 000) (138 000) (144 000) (150 000) Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. X X Lubricate outer tie rod ends 2500/3500 (4X4) models. X[...]

Miles 97,500 100,000 101,250 105,000 108,750 112,500 (Kilometers) (156 000) (160 000) (162 000) (168 000) (174 000) (180 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X XXXX Flush and replace engine coolant, if not r eplaced at 60 months. X Rotate tires. X X X Check spare tir e for prop[...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). X X XXXX Rotate tires. X X X Check spare tir e for proper pr essure and cor- rect stowage. XX X Flush and replace engin[...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Inspect front wheel bearings. X Change rear axle fluid. X X Change front axle fluid (4X4). X X Change 6-spd manual transmission (G-56) fluid 2500/3500. X Inspect brake linings. X X Inspect and adjust parking brake if neces[...]

Schedule “A” Miles 7,500 15,000 22,500 30,000 37,500 (Kilometers) (12 000) (24 000) (36 000) (48 000) (60 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stow- age. X X X[...]

Miles 45,000 52,500 60,000 67,500 75,000 (Kilometers) (72 000) (84 000) (96 000) (108 000) (120 000) [Months] [36] [42] [48] [54] [60] Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X X X X X Lubricate[...]

Miles 82,500 90,000 97,500 100,000 105,000 (Kilometers) (132 000) (144 000) (156 000) (160 000) (168 000) [Months] [66] [72] [78] [84] Change engine oil and engine oil filter . X X Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). X X X X X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X X X X X Lubricate o[...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). X X XXXX Rotate tir es. X X X X X X Check spare tir e for proper pr essure [...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [120] Inspect front wheel bearings. X X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X X Adjust valve lash clearance. X Inspection and service should also[...]

[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle ....................... 4 7 0 ▫ Prepar e For The Appointment ............ 4 7 0 ▫ Prepar e A List ........................ 4 7 0 ▫ Be Reasonable W ith Requests ............. 4 7 0 䡵 If Y ou Need Assistance ................... 4 7 0 䡵 W arran[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the deale[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the U[...]

W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SA[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is required when or dering manuals. (No P .O. Boxes). •[...]

Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .daimlerchrysler .com • www .daimlerchrysler .ca/manuals DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the Nationa[...]

on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor - mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. T emperature Grades The temperature [...]

INDEX 10[...]

Adding Fuel ........................... 3 2 0 Adjustable Pedals ....................... 1 3 2 Air Cleaner , Engine (Engine Air Cleaner Filter) . 389,418 Air Conditioner Maintenance ............... 3 9 6 Air Conditioning Refrigerant ............. 396,397 Air Conditioning System ................ 237,396 Air Conditioning System, Zone Control ........ [...]

Axle Fluid .......................... 412,447 Axle Lubrication (Axle Fluid) ............... 4 1 2 Ball Joints ............................. 3 9 7 Battery ............................... 3 9 4 Blanket .......................... 262,396 Emergency Starting ..................... 3 6 7 Keyless T ransmitter Replacement (RKE) ....... 2 3 Saving Feature (P[...]

CD (Compact Disc) Player ............ 190,198,21 1 Cellular Phone .......................... 8 7 Center High Mounted Stop Light ............ 4 4 0 Center Lap Belts ......................... 4 2 Center Seat Storage Compartment ......... 159,160 Certification Label ....................... 3 2 3 Charge Air Cooler ....................... 4 0 8 Chart, T[...]

T emperature Gauge ..................... 1 8 1 Cruise Contr ol (Speed Control) .............. 1 3 3 Cup Holder ............................ 1 5 5 Customer Assistance ..................... 4 7 0 Data Recorder , Event ...................... 5 6 Daytime Running Lights ................... 1 2 5 Dealer Service .......................... 3 8 0 Defroster [...]

T ow Hooks .......................... 3 7 1 T owing ............................. 3 7 2 Emission Control System Maintenance ......... 4 5 0 Engine ............................... 3 7 8 Air Cleaner .......................... 3 8 9 Block Heater ....................... 254,261 Break-In Recommendations ................ 7 1 Compartment .................[...]

Fold Flat Load Floor ..................... 1 6 6 Four Wheel Drive ....................... 2 7 6 Four-W ay Hazard Flasher .................. 3 5 4 Freeing A Stuck V ehicle ................... 3 7 0 Front Axle (Differential) ................ 398,41 1 Fuel .............................. 318,320 Adding ............................. 3 2 0 Diesel .......[...]

Passing ............................. 1 2 8 Switch .............................. 1 2 4 Heated Mirrors ....................... 85,164 Heated Seats ........................... 1 1 9 Heater ............................... 2 3 7 High Beam/Low Beam Select (Dimmer) Switch . . 128 Hitches T railer T owing ........................ 3 3 1 Hoisting .........[...]

Keys ................................. 1 2 Lane Change and T urn Signals .............. 1 2 7 Lap Belts .............................. 4 2 Lap/Shoulder Belts ....................... 3 2 LA TCH (Lower Anchors and T ether for CHildren) . 62 Life of T ires ............................ 3 1 1 Lights .............................. 75,122 Airbag .........[...]

T urn Signal .................. 127,179,433,437 W arning (Instrument Cluster Description) ..... 1 7 9 Limited-Slip Differ ential ................ 287,412 Loading V ehicle ......................... 3 2 3 T i r e s ............................... 3 0 0 Locks ................................. 2 4 Child Protection ........................ 2 7 Door ....[...]

Noise Control Maintenance .......................... 4 1 7 T ampering Prohibited ................... 4 1 8 Noise Emission W arranty ............... 417,419 Occupant Restraints ....................... 3 1 Occupant Restraints (2500/3500/Mega Cab Only) . . 31 Odometer .......................... 182,186 T r i p ............................. 182,186 Off[...]

Phone, Cellular .......................... 8 7 Phone, Hands-Free (UConnect™) ............. 8 7 Pickup Box ............................ 1 6 9 Placard, T ire and Loading Information ......... 3 0 0 Power Distribution Center (Fuses) ............... 4 2 6 Door Locks ........................... 2 5 Mirrors .............................. 8 4 Outlet (Au[...]

Recreational T owing ...................... 3 4 5 Shifting into T ransfer Case Neutral (N) .... 345,348 Shifting out of T ransfer Case Neutral (N) . . . 347,350 Refrigerant ............................ 3 9 7 Reminder , Seat Belt ....................... 4 3 Remote Keyless Entry (RKE) ................. 2 0 Remote Sound System (Radio) Controls .......[...]

Reclining ............................ 1 1 1 Reclining Rear ........................ 1 1 4 Security Alarm (Theft Alarm) ............. 18,182 Selection of Coolant (Antifreeze) .......... 403,446 Sentry Key (Immobilizer) ................... 1 5 Service Assistance ....................... 4 7 0 Service Contract ......................... 4 7 2 Service I[...]

Steering Linkage ............................. 3 9 8 Power ........................... 294,397 Wheel Lock ........................... 1 5 Wheel, T ilt ........................... 1 3 0 Steering Wheel Mounted Sound System Controls ............................. 2 3 1 Storage, Behind the Seat ................... 1 5 9 Storage Compartment, Center Seat [...]

Quality Grading ....................... 4 7 5 Radial .............................. 3 0 7 Replacement .......................... 3 1 1 Rotation ............................. 3 1 5 Safety ........................... 295,304 Sizes ............................... 2 9 7 Snow T ires ........................... 3 1 5 Spare T ire .........................[...]

T ransmission Automatic ........................ 267,413 Fluid ............................... 4 4 7 Maintenance .......................... 4 1 3 Manual ........................ 253,274,412 Shifting ............................. 2 6 7 T ransmitter Battery Service (Remote Keyless Entry) . 23 T ransmitter , Garage Door Opener (HomeLink 威 ) . . 143 [...]

Wheel Nut T orque .................... 361,365 W ind Buffeting ....................... 31,152 W indow Airbag (Side Curtain) ............... 5 4 W indow Fogging ........................ 2 4 5 W indows .............................. 2 9 Power ............................... 2 9 Rear Sliding ........................ 31,165 W indshield Defroster ......[...]

NOTES[...]

NOTES[...]