Dodge 2007 Nitro manuel d'utilisation

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 7 4 INSTRUMENT P ANEL AND CONTROLS .........................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 ▫ Roll Over W arning ..................... 5 䡵 How T o Use This Manual .................. 6 䡵 W arnings And Cautions ................... 8 䡵 V ehicle Identification Number ............... 8 䡵 V ehicle Modifications / Alterations ........... 9 1[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

Roll Over W arning Utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity , and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-r oad applications. Driven in an unsafe manner , all vehicles c[...]

million annually . In a roll over crash an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all su[...]

INTRODUCTION 7 1[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. VEHICLE IDE[...]

VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 9 1[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 4 ▫ Ignition Key Removal ................... 1 4 ▫ Key-In-Ignition Reminder ................ 1 6 䡵 Steering Wheel Lock — If Equipped .......... 1 6 ▫ T o Manually Lock The Steering Wheel ....... 1 6 ▫ T o Release The Steering Wheel L[...]

▫ Programming Additional T ransmitters ........ 2 4 ▫ Battery Replacement .................... 2 4 ▫ General Information .................... 2 5 䡵 Remote Starting System — If Equipped ........ 2 6 䡵 Door Locks ............................ 2 7 ▫ Manual Door Locks ..................... 2 8 ▫ Power Door Locks ..................... 2 9[...]

䡵 Engine Break-In Recommendations ........... 7 4 䡵 Safety T ips ............................ 7 4 ▫ Exhaust Gas .......................... 7 4 ▫ Safety Checks Y ou Should Make Inside The V e h i c l e .............................. 7 5 ▫ Safety Checks Y ou Should Make Outside The V e h i c l e .............................. 7 6 THINGS TO [...]

A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number . The key code can also be obtained by the dealer from your vehicle invoice. Ignition Key Removal Manual T ransmission T urn the ignition switch to the A[...]

Automatic T ransmission — If Equipped Place the shift lever in P (Park). T urn the ignition switch to the ACC position, push the key and cylinder inward, rotate the key to the LOCK position, and r emove the key . W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children[...]

Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to r emove the key . STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle without the ignition key . If the steering[...]

the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine. NOTE: A key that has not been programmed is consid- ered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the “V ehicle Security [...]

NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key T ransponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into th[...]

General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interfer ence that may cause undes- ired operation. SECURITY[...]

T o Disarm the System T o disarm the system, use the remote keyless entry transmitter . Also, using a valid sentry key and moving the ignition switch to the ON/ST AR T position will disarm the system. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. Th[...]

The lights also will fade to off if you turn on the ignition after you close all the doors. REMOTE KEYLESS ENTR Y NOTE: For the remote starting featur e (if equipped), refer to the “Remote Starting System” section. NOTE: Y our vehicle’s keyfob may have three, or four buttons, depending on the optional features pur chased with your vehicle. Th[...]

On electronic vehicle information center (EVIC) equipped vehicles refer to “Remote Unlock Driver’s Door 1st” under “Personal Settings” in the EVIC section (Sec- tion 4) of this manual. On non EVIC – equipped vehicles perform the following steps: 1. Perform this operation while standing outside the vehicle. 2. Pr ess and hold the “Lock[...]

1. Perform this operation while standing outside the vehicle. 2. Pr ess and hold the “Lock” button on a programmed (i.e. functional) key fob. 3. Continue to hold the “Lock” button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the P ANIC button. Release both buttons at the same time. 4. T o reactivate this feat[...]

horn. In case one should go off in the futur e, you will need to know which mode has been activated in order to deactivate it. T o activate the Panic mode while the ignition is OFF , press and r elease the P ANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights w[...]

1. If the key fob is equipped with a scr ew , remove the screw . W ith the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the seal during r emoval. 2. Remove and r eplace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterior[...]

NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. If your Keyless Entry T ransmitter fails to operate from a normal distance, check for these two conditions. 1. W eak batteries in transmitter . The expected life of the batteries is from one to[...]

Once the vehicle has started, the engine will run for 15 minutes. T o cancel remote start, pr ess the “Remote Start” button once. T o enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the “Unlock” button on the key fob. After the vehicle is unlocked, you have 60 seconds to enter the[...]

three single chimes will occur (One chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes). If the trip/reset button is pr essed while the VF warnings are being displayed, the VF display will r evert back to only displaying the odometer/trip odometer mileage. Manual Door Locks Use[...]

W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Un[...]

locks will not operate. This prevents you fr om acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to r emove the key . Automatic Door Locks If this feature is selected your door locks will lo[...]

W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle. WINDOWS Power Win[...]

Power Off to Accessories Until Exit” in Section 4 of this manual. Opening a vehicle front door will cancel this feature. W ARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment [...]

Auto Up Feature with Anti-Pinch Protection (Driver’s and Front Passenger Door Only) Lift the window switch to the second detent, release, and the window will go up automatically . T o stop the window from going all the way up during the auto-up operation, push down on the switch briefly . T o close the window part way , lift the window switch to [...]

W indow Lockout Switch The window lockout switch on the driver’s door (below the power window switches) allows you to disable the window control on the other doors. T o disable the window controls on the other doors, pr ess the window lockout button. T o enable the window controls, pr ess the window lockout button again. Power W indow Lock 34 THI[...]

Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with[...]

T o open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate. W ARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. Y ou and your pas- sengers could be injured by these fumes. Keep the liftgate[...]

NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have differ ent rates of inflation that are based on collision severity . Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. W ARNING! In a coll[...]

Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a colli- sion, the belt will lock and reduce the risk of you [...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. Latch Plate THINGS TO KNOW BEFORE ST [...]

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is[...]

4. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in the lap portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! A lap belt worn too high can increase t[...]

6. T o release the belt, push the r ed button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow it to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodical[...]

As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically pre- loc[...]

W ARNING! • The belt and retractor assembly must be replaced if the seat belt assembly “automatic locking re- tractor” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in colli[...]

seconds or until the driver seat belt is buckled. The Enhanced W arning System (BeltAlert) will be reactivated if the driver seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps[...]

Pregnant women should wear the lap part of the belt across the thighs and as snug acr oss the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if ther e is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjus[...]

Driver And Front Passenger Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt r estraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words[...]

This vehicle is equipped with window bags to protect the driver , front, and r ear passengers sitting next to a win- dow . They are located above the side windows. Their covers are also labeled SRS/AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. W ARNING! • Do not put anything on[...]

The front airbags have a multi stage inflator design. This allows the airbag to have differ ent rates of inflation that are based on collision severity . Along with the seat belts, front airbags work with the instr ument panel knee bol- sters to provide impr oved protection for the driver and front passenger . W indow bags also work with seat belts[...]

children who do not use child r estraints or belt- positioning booster seats should ride properly buckled up in the rear seat. Never allow childr en to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old must ride in the fr ont passenger seat because the vehicle is crowded, move the seat as far back as possible[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instru- ment panel during airbag de[...]

• Driver and Front Passenger Seat Belt Pr etensioner • Occupant Classification System (OCS) — Front Pas- senger Seat Only − Occupant Classification Module − Passenger Airbag Disable (P AD) Indicator Light − W eight Sensors How The Airbag System W orks • The Occupant Restraint Control (ORC) Module de- termines if a frontal, side, or r [...]

either momentarily or continuously . A single chime will sound if the light comes on again after initial start up. W ARNING! Ignoring the “Airbag W arning Light” in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on[...]

objects are placed on the seat, the passenger airbag will not inflate even though the “P AD Indicator Light” is not illuminated. The “P AD Indicator Light” should not be illuminated when a adult passenger is properly seated in the fr ont passenger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occu[...]

Front Passenger Seat Occupant Passenger Air- bag Disable (P AD) Indicator Light Airbag Status Adult OFF ON Grocery Bags, Heavy Briefcases and Other Rela- tively Light Ob- jects ON OFF Empty or V ery Small Objects OFF* OFF * Since the system senses weight, some small objects will turn the P AD Indicator Light on. The OCS classifies an occupant using[...]

because this can also affect occupant classification. Also, if you fold down the rear seat check to be sur e it doesn’t touch the front passenger seat. If the front passenger seat is damaged in any way , it should only be serviced by an authorized dealer . If the seat is removed (or even if the seat attachment bolts ar e loosened or tightened in [...]

The driver front airbag gas is vented thr ough the vent holes in the sides of the airbag. The passenger front airbag gas is vented through the vent holes in the sides of the airbag. In this way , the airbags do not interfere with your control of the vehicle. • The Occupant Classification Module (OCM) is lo- cated beneath the front passenger seat.[...]

The front passenger seat assembly contains critical com- ponents that affect the fr ont passenger airbag deploy- ment. Correctly functioning fr ont passenger seat compo- nents are critical for the Occupant Classification System (OCS) to properly classify the fr ont passenger and calcu- late the proper airbag deployment. Do not make any modification[...]

W ARNING! Unapproved modifications or service procedures to the front passenger seat assembly , its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an acci- dent. A modified vehicle ma[...]

• As the airbags deflate you may see some smoke-like particles. The particles are a normal by-pr oduct of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water . For nose or throat irritation, [...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right [...]

data during and/or after air bag deployment or near- deployment. EDR data are ONL Y recor ded if an airbag deploys, or nearly deploys, and are otherwise unavail- able. NOTE: • A near -deployment event occurs when the airbag sensor detects severe vehicle deceleration usually in- dicative of a crash, but not severe enough to warrant airbag deployme[...]

nature, such as would identify a particular driver , ve- hicle, or crash, will be treated confidentially . Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1. Used for resear ch purposes, such as to match data with a particular crash recor d in an aggregate database, provided confidentiality o[...]

Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it. Children 12 years and under should ride pr operly buck- le[...]

Infants and Child Restraints • Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearwar d-facing in t[...]

Here ar e some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufactur er also recommends that you try a child restraint in the vehicle seats wher e you will use it before you buy it. • The restraint must [...]

• In the rear seat, you may have tr ouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the rele[...]

The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who ar e still too small to fit the vehicle’s seat belts properly . If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and bel[...]

having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufactur ers offer add-on tether strap[...]

install the child restraint. Y ou will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. In addition, there ar e tether strap anchorages behind each rear seating position located on the back of the seat. Latch Anchorages T ether Strap Mounting 70 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE[...]

Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some r ear-facing infant restraints will also be equipped with a tether strap, a hook for attach[...]

Installing Child Restraints Using the V ehicle Seat Belt The passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors, which ar e designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on[...]

Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, r oute the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat. W ARNING! An incorrectly anchored tether strap could lead to increased head motion an[...]

ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not r equired for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-thr ottle acceleration, within the limits of local traffic laws, c[...]

garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine r unning for more than a short period, adjust the ventilation system to force fr esh, outside air into the vehicle. • Guard against carbon monoxide with pr oper mainte- nance. Have the exhaust system inspe[...]

Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should feel the air directed against the windshield. Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tr ead wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the trea[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 M i r r o r s ............................... 8 1 ▫ Inside Day/Night Mirror ................. 8 1 ▫ Automatic Dimming Mirror — If Equipped .... 8 2 ▫ Outside Mirrors ....................... 8 2 ▫ Exterior Mirrors Folding Featur e ........... 8 3 ▫ Power Remote Control Mirr ors ..[...]

▫ 6–W ay Driver’s Power Seat W ith Manual R e c l i n e r ............................ 1 1 2 ▫ Fold Flat Front Passenger Seat ............ 1 1 3 ▫ Head Restraints ...................... 1 1 3 ▫ Heated Seats — If Equipped ............. 1 1 3 ▫ 60/40 Split Folding Rear Seat W ith Fold Flat Feature ............................ 1 1 5 ?[...]

▫ T o Set At A Desir ed Speed ............... 1 2 6 ▫ T o Deactivate ........................ 1 2 6 ▫ T o Resume Speed ..................... 1 2 6 ▫ T o V ary The Speed Setting ............... 1 2 6 ▫ Manual T ransmission .................. 1 2 7 ▫ T o Accelerate For Passing ............... 1 2 7 䡵 Electronic Brake Contr ol System ...[...]

▫ Sunshade Operation ................... 1 4 3 ▫ W ind Buffeting ....................... 1 4 3 ▫ Sunroof Maintenance ................... 1 4 4 䡵 Electrical Power Outlet ................... 1 4 4 ▫ Electrical Outlet Use W ith Engine Off ....... 1 4 5 䡵 Power Inverter ........................ 1 4 6 䡵 Cup Holders ........................[...]

MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the r ear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of truck). The mirror should [...]

Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying head- light glare fr om vehicles behind you. Y ou can turn the feature on or of f by pressing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cle[...]

W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror . Exterior[...]

Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upwar d. The lights will turn on automati- cally . Closing the mirror cover will turn off the light. Sun V isor “Slide-Out” Feature The sun visor “slide-on rod ” featur e a[...]

NOTE: The UConnect™ system use requir es a cellular phone equipped with the Bluetooth ⬙ Hands-Free Pr ofile, ⬙ version 0.96 or higher . See www .chrysler .com/uconnect for supported phones. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system?[...]

The rearview mirr or contains the microphone for the system and the radio has the two control buttons that will enable you to access the system. Actual button location may vary with radio. The individual buttons are de- scribed in the “Operations” section. The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ c[...]

Operations V oice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structur e. V oice commands are r equired after most UConnect™ system prompts. Y ou will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the [...]

Cancel Command At any prompt, after the beep, you can say ⬙ Cancel ⬙ and you will be returned to the main menu. However , in a few instances the system will take you back to the previous menu. Pair (Link) UConnect™ System to a Cellular Phone T o begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular p[...]

• Y ou will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority . Y ou can pair up to seven cellular phones to your UConnect™ system. However , at any given time, only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know wh[...]

• System will prompt you to say the name of the person you want call. • After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a pr evi- ously stored name entry in the UConnect™ phone book. Refer to ⬙ Add Names to Y our UConnect™ Phon[...]

The UConnect™ system will allow you to enter up to 32 names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing names in the phone book is recom- mended when vehicle is[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Delete. ⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. Y ou can either say the name of a phone book entry that you wish to delete or you can say ⬙ List Names ⬙ to hear a list of the entries i[...]

• The UConnect™ system will play the names of all the phone book entries. • T o call one of the names in the list, press the ⬙ V oice Recognition’ button during the playing of the desired name, and say ⬙ Call. ⬙ NOTE: The user can also exercise ⬙ Edit ⬙ or ⬙ Delete ⬙ operations at this point. • The UConnect™ system will th[...]

NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progr ess. Therefor e, the user can only either answer an incoming call or ignore it. Making a Second Call while Current Call in Progress T o make a second call while you are curr ently in a call, press the ’V oice Reco[...]

established, press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call T ermination T o end a call in progr ess, momentarily press the ⬘ Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active ca[...]

• An active call is automatically transferred to the mobile phone after ignition key is switched to off. UConnect™ System Features Language Selection T o change the language that the UConnect™ system is using, • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you[...]

NOTE: The emergency number dialed is based on the Country where the vehicle is pur chased (91 1 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone direct[...]

W orking with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated tele- phone system. Y ou can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer ser[...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The UConnect™ system will play the current confirmation pr ompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster , and suppo[...]

In order to un-mute the UConnect™ system: • Press the ’V oice Recognition’ button. • Following the beep, say ⬙ Mute-off. ⬙ Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc. related informatio[...]

• The UConnect™ system will play the phone names of all paired cellular phones in or der from the highest to the lowest priority . T o “select” or “delete” a paired phone being announced, press the ⬘ V oice Recognition’ button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” [...]

• Y ou can also press the ⬘ V oice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete. Things Y ou Should Know About Y our UConnect™ System V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers, the UCon- nect™ system V oice T [...]

• Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in [...]

• low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • operation from driver seat. • Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduc[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3[...]

106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 107 3[...]

V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call cancel confirmation prompts continue delete dial edit emergency English erase all Espanol Fancais help home language list names list phones 108 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call try again voice training work yes UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 109 3[...]

SEA TS Front Manual Seat Adjustment Move the seat forward or r earward using the adjustment bar . Lift up on the bar located on the front of the seat near the floor . Position the seat and be sure the latch engages fully . Using body pressur e, move forward and r earward on the seat to be sure the seat adjusters have latched. W ARNING! Adjusting a [...]

Front Seat Adjustment — Recline T o adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and r elease the lever at the desired position. T o return the seatback, lift the lever , lean forward, and r elease the lever . W ARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting ag[...]

6–W ay Driver’s Power Seat with Manual Recliner The seat switch is on the outboard side of the seat near the floor . Use this switch to move the seat up or down, forward or r earward, or to tilt the seat. This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. Power [...]

Fold Flat Front Passenger Seat The front passenger seat can be folded flat to allow for extended cargo space. Pull up on the lever to fold down the seat back. Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Adjustable head restraints should be adjusted so that the upper edge is as high[...]

indicate the level of heat in use. T wo LEDs are illumi- nated for high, one for low , and none for off. Pr essing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating. Pressing the switch a thir d time will shut the heating elements off. When high-temperature heating is selected, the heate[...]

W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time. Do not place an[...]

Also, be sure that the fr ont seats are fully upright and positioned forward. This will allow the r ear seat to fold down easily . W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to[...]

4. If desir ed, push down on the seatback to lock it in the folded position. T o Raise Rear Seat If locked in the folded position, pull the release strap (toward the fr ont of the vehicle). Raise the seatback and lock it into place. If interference from the car go area pr events the seatback from fully locking, you will have difficulty r eturning t[...]

Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center . T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center fr ont edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both la[...]

LIGHTS Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the contr ol for the dimmer switch on the multi-function control lever fully upward. The overhead light will automatically turn of f in about 20 minutes if a door is left open or the dimmer control is left in the dome light position. T urn[...]

Parking Lights, Instrument Panel Lights, and Headlights T urn the end of the multi-function control lever to the first detent for parking lights and instrument panel lights. T urn to the second detent for headlight operation. T o change the brightness of the instrument panel lights, rotate the center portion of the multi-function contr ol lever up [...]

Passing Light Y ou can signal another vehicle with your headlights by lightly pulling the multi-function control lever towar d the steering wheel. This will cause the headlights to turn on at high beam and remain on until the lever is r eleased. Front Fog Lights — If Equipped The front fog light switch is in the multi-function control lever . T o[...]

Daytime Running Lights — If Equipped The headlights come on at a low intensity level after the vehicle has been driven approximately 3 feet (1 meter). They will turn off when the vehicle is turned of f or when the headlights are switched on. WINDSHIELD WIPERS AND W ASHERS CAUTION! In cold weather , always turn off the wiper switch and allow the w[...]

Windshield Wiper Operation Move the lever upward to the second detent for LO speed wiper operation, or to the third detent for HI speed operation Windshield W ashers T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the le[...]

TIL T STEERING COLUMN T o tilt the column, push down on the lever under the multi-function control lever and move the wheel up or down, as desired. Pull the lever back upwar ds to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose cont[...]

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. T o Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. T o turn the system OFF , pu[...]

T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground befor e pressing the SET lever . T o Deactivate A soft tap on the brake pedal, pullin[...]

T apping the “SET DECEL” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. NOTE: The Speed Control system has been designed to shut down if multiple speed control switch functions ar e operated simultaneously in order to ensur e proper op- eration. If this occurs, the system can be reac[...]

On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed contr ol. ELECTRONIC BRAKE CONTROL SYSTEM Y our vehicle is equipped with an advanced electronic brake control system that includes ABS (Anti-Lock Brake System), TCS (T raction Control System), BAS (Brake Assist System), ERM (Electronic Roll Mitigati[...]

TCS (T raction Control System) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressur e is applied to the slipping wheel(s) and engine power is reduced to pr ovide enhanced acceleration and stability . A feature of the TCS system functions similar to a limited slip differ ential and cont[...]

W ARNING! BAS (Brake Assist System) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing. Only a safe, attentive, a[...]

W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur . ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent acci[...]

ESP/TCS Indicator Light The ⬙ ESP/TCS Indicator Light ⬙ located in the instrument cluster , starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ ESP/TCS Indicator Light ⬙ also flashes when TCS is active. If the ⬙ ESP/TCS Indicator Light ⬙ begins to flash during acceleration, ease up on the accelera[...]

ESP On This is the normal operating mode for ESP in 2WD, 4WD Part T ime, 4WD Full T ime, and on 2WD vehicles. When- ever the vehicle is started, the ESP system will be in this mode. This mode should be used for most all driving situations. ESP should only be turned of f for specific reasons as noted below . Partial Of f This mode is entered by mome[...]

situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily depressing the “ESP OFF” switch. This may be done while the vehicle is in motion. ESP/BAS W arning Lamp The malfunction indicator lamp for the ESP is combined with BAS. The “ESP/BAS W arning Lamp” and the “ESP/TCS Indicator Li[...]

The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal T ransceiver operates off your vehicle’s battery and charging system; no batteries are neede[...]

Programming The Universal T ransceiver For best results, install a new battery in the hand held transmitter before pr ogramming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the v[...]

1. T urn off the engine. 2. Erase the factory test codes by pr essing the two outside buttons. Release the buttons when the light in the Universal T ransceiver begins to flash (about 20 seconds). NOTE: Do not repeat Step 2 to pr ogram additional hand held transmitters. 3. Choose one of the thr ee Universal T ransceiver buttons to program. Place the[...]

5. The indicator light in the Universal T ransceiver will begin to flash, first slowly and then rapidly . The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and r epeat the procedur e. T o train the other buttons, repeat steps 3 and 4. Be sur e to keep yo[...]

NOTE: The assistance of a second person may make the following programming pr ocedure quicker and easier . 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer . If you have difficulty in locating the training button, check your garage door opener ma[...]

The Universal T ransceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor . Operation Press and hold the desir ed button on the Universal T ransceiver until the garage door or other de[...]

2. This device must accept any interfer ence that may be received including interfer ence that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. HomeLink 威 is a trademark owned by Johnson Controls, Inc. POWER S[...]

W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle wi[...]

sunroof will automatically r etract. Remove the obstruc- tion if this occurs. Next, press the switch forwar d and release to Expr ess Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) pr events closing, press the switch forwar d and hold. This allows the sunroof to move towar ds the closed position. NOTE: Pinch protection is [...]

Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. ELECTRICAL POWER OUTLET This vehicle has two auxiliary power outlets that can provide up to 20 Amps of current for accessories de- signed for use with the standard power outlet adapters. The front power outlet located in the lower portion of the instrumen[...]

The rear power outlet (if equipped) is located in the left rear car go area. Electrical Outlet Use With Engine Off W ARNING! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficien[...]

POWER INVERTER There is a 1 10–volt, 150–watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can be used to power small appliances and electronics. Press the switch located in the center stack lower switch bank to turn the power on to the outlet. Press the switch again to turn the powe[...]

W ARNING! T o A void Serious Injury or Death: • Do not use a 3—Prong Adaptor . • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUP HOLDERS In the center console there ar e two cup holders for the f[...]

The rear passengers have cup holders at the r ear of the center console. STORAGE Front Storage Compartment The front storage compartment (located on the left side of the instrument panel) can hold cell phones, PDA’s, and other small items. Rear Cup Holders Front Storage Compartment 148 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

Console Storage Compartment T o open, press the latch and lift cover . The center console has a removable storage tray which can hold cell phones, PDA’s, and other small items. Center Console Removable Storage T ray UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 149 3[...]

CARGO AREA FEA TURES Cargo Light The cargo ar ea light is activated by opening the liftgate, opening any door , or by rotating the dimmer contr ol on the multi-function control lever to the extr eme top posi- tion. Cargo Tie-Down Hooks The tie-downs located on cargo ar ea floor should be used to safely secure loads when vehicle is moving. W ARNING![...]

• Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous pr ojectile in a sudden stop or collision. W ARNING! T o help protect against personal injury , passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only , not for pa[...]

2. Lift cover . 3. Flip cover over , and lock panel back into position. Utility T able — If Equipped The cargo load floor can be converted into a utility table. The maximum load capacity of the utility table is 100 lbs (45 kg). In order to use the utility table, use the following procedur e: Load Floor 152 UNDERST ANDING THE FEA TURES OF YOUR VEH[...]

1. Push side mounted r elease handles (toward center of vehicle) to release cover . 2. Lift the cover and r emove from vehicle. 3. Flip the cover over , and remove table legs from their retainers. 4. Insert the legs into their corner positions. 5. Set the table on level gr ound. CAUTION! T o avoid personal injury , do not stand or sit on the table.[...]

1. Open the tailgate. 2. Squeeze the right hand r elease handle. 3. Pull out the sliding panel. 4. Squeeze the right hand r elease handle to slide the panel back into the vehicle. Release Handle Sliding Panel 154 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

REAR WINDOW FEA TURES Rear Window Wiper/W asher — If Equipped A rotary ring switch on the control lever (located on the right side of the steering column), controls operation of the rear wiper/washer function. Rotating the center of the switch up to the “On” position will activate the wiper . Rotating the switch ring beyond the “On” or ?[...]

If the swing gate flip-up window is open or the swing gate is open, connection to the rear window wiper is interrupted pr eventing activation of the rear wiper blade. When the swing gate flip-up window or the swing gate is closed, the rear wiper switch or the ignition switch needs to be turned OFF , and then to ON to restart the r ear wiper . NOTE:[...]

CAUTION! Use care when washing the inside of the rear win- dow to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements. ROOF LUGGAGE RACK — IF EQUIPPED The load carried on the roof w[...]

CAUTION! T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity . Always distribute heavy loads as evenly as possible and secure the load appropriately . Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. Place a blank[...]

INSTRUMENT P ANEL AND CONTROLS CONTENTS 䡵 Instrument Panel And Controls ............. 1 6 2 䡵 Instrument Cluster ...................... 1 6 3 䡵 Instrument Cluster Description ............. 1 6 4 䡵 Compass And T rip Computer — If Equipped . . . 175 ▫ Control Buttons ...................... 1 7 6 ▫ T rip Conditions ......................[...]

▫ Electrical Disturbances .................. 1 9 1 ▫ AM Reception ....................... 1 9 1 ▫ FM Reception ........................ 1 9 1 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA Aux Jack) ................... 1 9 2 ▫ Operating Instructions - Radio Mode ....... 1 9 2 ▫ Operation Instructions - (Dis[...]

▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) .................... 2 2 1 ▫ Selecting Satellite Mode (RSC Radios) ....... 2 2 2 ▫ Satellite Antenna ...................... 2 2 2 ▫ Reception Quality ..................... 2 2 2 ▫ Operating Instructions - Satellite Mode ...... 2 2 2 ▫ Operating Instructions - Hands Fr ee [...]

INSTRUMENT P ANEL AND CONTROLS 162 INSTRUMENT P ANEL AND CONTROLS[...]

INSTRUMENT CLUSTER INSTRUMENT P ANEL AND CONTROLS 163 4[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Fuel Cap Indicator This symbol indicates the side of the vehicle where the fuel cap is located. 3. T emperature Gauge The temperature gauge indicates engine coolant temperature. Any r eading within the normal range [...]

5. Seat Belt Reminder Light This light comes on for several seconds after the ignition is turned ON as a reminder to “buckle up.” This light will remain on as long as the seat belt remains unbuckled. If this light flashes, it indicates a fault in the airbag system. Have the system checked by an authorized dealer . 6. Coolant T emperature W arni[...]

W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 7. Speedometer Shows[...]

after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. NOTE: The ⬙ ESP/TCS Indicator Light ⬙ and the ⬙ ESP/ BAS W arning Lamp ⬙ come on momentarily each time the ignition switch is turned ON. The ESP Contr ol System will make buzzi[...]

bulb check. If the bulb does not come on during starting, see your authorized dealer for service. If the light stays on, it may be an indication that the parking brake has not been released, or ther e is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master[...]

16. Electr onic Stability Program (ESP) Indicator Light/T raction Control System (TCS) Indicator Light The yellow ESP indicator light in the speedom- eter area illuminates with the key in the igni- tion switch turned to the ON/RUN position. It should go out with the engine running. The ⬙ ESP/TCS Indicator Light ⬙ starts to flash as soon as the [...]

approximately 3 seconds. If this light r emains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed. See your authorized dealer immedi- ately . W ith the ABS malfunctioning, the BAS and ESP are also switched off. Both malfunction indicator lights illu- minate wi[...]

24. T ransmission Range Indicator The electronic gear selector display is self-contained within the instrument cluster . It displays the position of the automatic transmission shift lever , and the relation of each position to all other positions. For a good signal the display will place a box around the selected transmission range (PRND21). If the[...]

maintain correct tir e pressur e, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pr essure telltale. The “T ire Pressur e Monitoring T elltale Light” will illumi- nate in the instrument cluster , and an audible chime will be activated when one or more tir e pressur es is low . The “T ire Pressur[...]

press the Odometer/T rip Odometer Button. T o reset the T rip Odometer , press and hold the button while in trip mode, until the T rip Odometer resets. If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instr ument cluster . T ighten the fuel filler cap pr[...]

CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required. 28. Cruise Indicator Light — If Equipped This indicator lights when the electroni[...]

COMP ASS AND TRIP COMPUTER — IF EQUIPPED The Compass/T rip Computer features a driver - interactive display (displays information on outside tem- perature, compass dir ection, and trip information). It is located on the lower left part of the cluster below the fuel and engine temperature gauge, and the tachometer . The compass/trip computer , whe[...]

• Loose Fuel Cap (gASCAP) These messages can be manually turned off by pr essing the right button (on the instrument cluster). Control Buttons Press and r elease the odometer/trip odometer reset but- ton (right side of the instrument cluster) to access the compass/trip computer displays. Display Button 176 INSTRUMENT P ANEL AND CONTROLS[...]

T rip Conditions T rip Odometer (ODO) This display shows the distance traveled since the last reset. Pr ess and release the right button (on the instru- ment cluster) to switch from odometer , to trip A or trip B. Press and hold the right button while the odometer/trip odometer is displayed to reset. T rip A Shows the total distance traveled for tr[...]

NOTE: Magnetic materials should be kept away from the top of the right rear quarter window . This is where the compass sensor is located. T o Set the V ariance Start the engine, and leave the transmission in the P (Park) position. Press and hold (appr oximately ten sec- onds) the odometer/trip odometer reset button until the current variance zone n[...]

T o Manually Calibrate the Compass Start the engine, and leave the transmission in the P (Park) position. Press and hold (appr oximately 10 sec- onds) the odometer/trip odometer reset button until the current variance zone number is displayed. Release the odometer/trip odometer reset button, then pr ess and hold again (approximately 10 seconds), un[...]

V ehicles equipped with steering wheel mounted buttons (described in this section) are also equipped with the EVIC. The EVIC consists of the following: • System Status • V ehicle information warning message displays • T ire Pressur e Monitor System (If Equipped) • Personal Settings (Customer Programmable Featur es) • Compass display • O[...]

Press and r elease the COMP ASS/ TEMPERA TURE button to display one of eight compass readings and the outside temperatur e. Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the Electr onic V ehicle Information Center (EVIC) displays the following messages: • T urn Signal On (with a continuous warning c[...]

• Right Front Low Pr essure (with a single chime). Refer to “T ire Pressur e Monitoring System” in Section 5 of this manual. • Right Rear Low Pressur e (with a single chime). Refer to “T ire Pressur e Monitoring System” in Section 5 of this manual. • Check TPM System (with a single chime). Refer to “T ire Pressur e Monitoring System[...]

and average fuel economy , according to the current fuel tank level. DTE cannot be reset thr ough the FUNCTION SELECT button. NOTE: Significant changes in driving style or vehicle loading will greatly af fect the actual drivable distance of the vehicle, regar dless of the DTE displayed value. • When the DTE value is less than 30 miles (48 km) est[...]

Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually . When the vehicle is new , the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. Y ou may also calibrate the compass by completing one or more 360° turns (in an area fr ee from lar ge [...]

NOTE: Magnetic materials should be kept away from the top of the right rear quarter window . This is where the compass sensor is located. INSTRUMENT P ANEL AND CONTROLS 185 4[...]

1. T urn the ignition switch ON. 2. Pr ess and hold the compass button for approximately 2 seconds. 3. Pr ess the SCROLL button until “Compass V ariance” message and the last variance zone number displays in the EVIC. 4. Pr ess and release FUNCTION SELECT button until the proper variance zone is selected accor ding to the map. 5. Pr ess and rel[...]

The EVIC displays this symbol to indicate an incoming call. The EVIC displays this symbol to indicate that the UConnect™ phone is currently in analog mode. The EVIC displays this symbol to indicate that the UConnect™ phone is currently r oaming. The EVIC displays this symbol to indicate that you have voice mail. The EVIC displays this symbol to[...]

The EVIC displays this symbol to indicate that a phone connection has been made. The EVIC displays this symbol to indicate that the Connect™ phone is currently not available. Personal Settings (Customer Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in P ARK. Press and r elease the M[...]

T o make your selection, press and r elease the FUNC- TION SELECT button until “ON” or “OFF” appears. Unlock Doors Automatically on Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the P (Park) or N (Neutral) position and the driver’s door is opened. T o make your selection, press and [...]

Delay T urning Headlights Off When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. T o make your selection, press and release the FUNCTION SELECT button until “0,” “30,” “60,” or “90” appears. T urn Headlights On with Remote Key Unlock When this [...]

RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will provide excellent r eception under most operating conditions. Like any system, however , car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. T o help you understand and sa[...]

will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle fr ont door will cancel this feature. SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode[...]

Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping. T urning the volume control to the right incr eases the volume and to the left d[...]

2. Adjust the hours by turning the right side TUNE control knob. 3. After the hours ar e adjusted, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE contr ol knob. Press the TUNE contr ol knob to save time change. 5. T o exit, press any button/knob or wait 5 s[...]

Press the r otary TUNE control knob a fifth time and F ADE will display . T urn the TUNE control knob to the left or right to adjust the sound level between the front and rear speakers. Press the r otary TUNE control knob again to exit setting tone, balance and fade. MUSIC TYPE Button (Radio Mode) Pressing this button once will turn on the Music T [...]

Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Ta l k Ta l k T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next frequency station with the same [...]

• DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly Pressing SELECT will switch subtitles to differ ent subtitle languages that are available on the disc (If Equipped). • Audio Stream – Repeatedly Pr essing SELECT will switch to differ ent audio languages (if supported on the disc) (If E[...]

Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If customer wishes to select a language not listed, then scroll down and select ⬙ other ⬙ . Enter the 4 digit country code using the TUNE control knob to scroll up and down to sele[...]

Aspect Ratio — If Equipped Selecting this item will allow the user to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to ON and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto play the main title. In such c[...]

Every time a preset button is used a corr esponding button number will be displayed. B u t t o n s1-6( Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch fr om AM/FM modes to Disc modes. [...]

Radio display will show ⬙ LOADING DISC ⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the eject button and the push-button[...]

R W/FF (CD MODE) Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM or FM Button (CD MODE) Switches the Radio to the Radio mode. RND Button (Random Play Button) (CD MODE) Press this button while the CD is[...]

• Maximum number of directory levels: 8 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are[...]

MPEG Specifi- cation Sampling Fre- quency (kHz) Bit rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48 WMA Specifica- tion Sampling Fre- quency (kHz) Bit Rate (kbps) WMA 44.1 and 48 48, 64, 96, 128, 160, 192 VBR ID3 T ag info[...]

LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE contr ol knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does n[...]

SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display fr om elapsed playing time to time of day . The time of day will be displayed for 5 seconds. R W/FF (Auxiliary Mode) No function. SET Button (Auxiliary M[...]

Macrovision This product incorporates copyright pr otection technol- ogy that is protected by U.S. patents and other intellec- tual property rights. Use of this copyright pr otection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineer[...]

Power Switch/V olume Control (Rotary) Press the ON/VOLUME contr ol knob to turn the radio on. Press the ON/VOLUME contr ol knob a second time to turn the radio off. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping. T urning the ON/VOLUME control knob to the right incr e[...]

2. Adjust the hours by turning the right side TUNE control knob. 3. After the hours ar e adjusted, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE contr ol knob. Press the TUNE contr ol knob to save time change. 5. T o exit, press any button/knob or wait 5 s[...]

Press the r otary TUNE control knob a fifth time and F ADE will display . T urn the TUNE control knob to the left or right to adjust the sound level between the front and rear speakers. Press the r otary TUNE control knob again to exit setting tone, balance and fade. MUSIC TYPE Button Pressing this button once will turn on the Music T ype mode for [...]

Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Ta l k Ta l k T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next frequency station with the same [...]

Select the button (1-6) you wish to lock onto this station and press and r elease that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this ex[...]

Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display . If a CD does not go into the slot more than an inch, a disc may already be loaded and must be ejected before a new disc can be loaded. If you ins[...]

If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not r emoved, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF . NOTE: Ejecting with ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the righ[...]

Press the right SEEK button to move to the next ran- domly selected track. Press the RND button a second time to stop Random Play . Notes On Playing MP3 Files The radio can play MP3 files, however , acceptable MP3 file recor ding media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (D[...]

• Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession dis[...]

Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: • Media - CD-R W media may take longer to load than C[...]

Press and hold the INFO button again for 3 seconds to return to ⬙ elapsed time ⬙ display . Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , or cassette player , and utilize the vehicle’s audio system to amplify the source and pla[...]

SALES CODE RER — AM/FM/CD/DVD RADIO WITH NA VIGA TION SYSTEM — IF EQUIPPED NOTE: The radio sales code is located on the lower right side of your radio faceplate. Satellite Navigation Radio with CD Player with MP3 Capability (RER) - combines a Global-Positioning System-based navigation system with an integrated color screen to pr ovide maps, tur[...]

either the H button on the faceplate to change the hour or the M button on the faceplate to change the minute. 2. The time setting will incr ease each time you press the button. Holding either button in will fast forward the setting. 3. If no changes ar e made within 5 seconds of accessing the Setup screen, the scr een will time out and you will be[...]

SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to r eceiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satel- lite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for chil- dren, dir ectly from i[...]

Selecting Satellite Mode (RSC Radios) Press the SA T button until ⬙ SA T ⬙ appears in the display . A CD may remain in the radio while in the Satellite radio mode. Satellite Antenna T o ensure optimum r eception, do not place items on the roof ar ound the rooftop antenna location or strap items to the trunk lid ar ound the trunk lid antenna (if[...]

SCAN Button Pressing the SCAN button causes the tuner to sear ch for the next channel, pausing for 8 seconds before continuing to the next. T o stop the search, pr ess SCAN a second time. INFO Button Pressing the INFO button will cycle between Artist, Song T itle, and Composer (if available) information. Also, pressing and holding the INFO button f[...]

• Display Sirius ID number — Press the SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscrip- tion. SET Button — T o Set the Push-Button Memory When you are r eceiving a channel that you wish to commit to push-button memory , press the SET button. The symbol SET 1 will now s[...]

VIDEO ENTERT AINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (V ideo Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-power ed remote contr ol, and two head- sets. Refer to your VES™ User’s Manual for detailed operating instructions. The LCD screen is located on the headline[...]

REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a push button in the center . Pressing the top of the switch will increase the volume and pr essing the bottom of t[...]

The left hand control is a r ocker type switch with a push button in the center . The function of the left hand control is differ ent depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the b[...]

3. Do not apply paper , paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner , cleaners, or antistatic sprays. 5. Stor e the disc in its case after playing. 6. Do not expose the disc to dir ect sunlight. 7. Do not stor e the disc where temperatures may become too high. CLIMA TE CONTROLS Ma[...]

Blower Control Use this control to r egulate the amount of air forced through the system in any mode you select. The fan speed increases as you turn the outer control ring to the right from the OFF position. T emperature Control Use this control to r egulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale[...]

Mode Control The mode control allows you to choose from several pat- terns of air distribution. Y ou can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribu- tion you receive fr om that mode. Panel Air is directed thr ough the four outlet[...]

Defrost Air is directed thr ough the windshield and side window demist outlets. Use this mode with maxi- mum fan and temperature (Hot) settings for best wind- shield and side window defrosting. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes even if the fan switch is not in the A/C position. This deh[...]

moisture build up inside the vehicle. For maximum defogging, select the Outside Air position. NOTE: Recirculation mode will not operate in floor , mix or defrost modes. Air Conditioning Operation Press the temperatur e control knob to activate the air condi- tioning mode. A lamp will illuminate when the Air Con- ditioning System is engaged. Press t[...]

smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to pr ovide proper corr osion protection and to raise the boiling point of the coolant for protection against over heating. A 50 % con[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 3 9 ▫ Manual T ransmission .................. 2 3 9 ▫ Automatic T ransmission ................ 2 3 9 ▫ Normal Starting ...................... 2 3 9 ▫ Extreme Cold W eather (Below –20°F Or –29°C) ................. 2 4 0 ▫ If Engine Fails T o Start ....[...]

䡵 Four-Wheel Drive Operation ............... 2 5 9 ▫ Mp 143 Single-Speed Part-T ime T ransfer Case — If Equipped ............. 2 5 9 ▫ Shifting Procedur e - Electronically Shifted T ransfer Case ................... 2 6 1 ▫ Mp 140 Single-Speed Full-T ime T ransfer Case — If Equipped ............. 2 6 2 䡵 On-Road Driving T ips .........[...]

䡵 T ire Pressur e Monitoring System (TPMS) — If Equipped ........................... 2 8 7 ▫ Base System — If Equipped .............. 2 9 0 ▫ Premium System — If Equipped .......... 2 9 1 ▫ General Information ................... 2 9 5 䡵 Fuel Requirements ...................... 2 9 6 ▫ 3.7L Engine (If Equipped) ............... 2 9[...]

▫ T o w i n g T i p s ......................... 3 1 9 䡵 Recreational T owing (Behind Motorhome, Etc.) ................. 3 2 1 ▫ T owing – 2WD Models ................. 3 2 1 ▫ T owing — 4WD Or All-Wheel Drive Models ........................ 3 2 1 238 ST ARTING AND OPERA TING[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. W AR[...]

T ip Start Feature — Automatic T ransmission Only Do not press the accelerator . T urn the ignition key briefly to ST AR T position, and release it. The starter motor will continue to run, but will automatically disengage itself when the engine is running. Extreme Cold Weather (below –20°F or –29°C) T o insure r eliable starting at these te[...]

W ARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way .[...]

released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor . Release the accelerator pedal and the key once the engine is running smoothly . If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor , the “Normal Starting” or “Extr[...]

ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather . Connect the cord to a standard 1 10-1 15 volt AC electrical outlet with a grounded, thr ee wire extension cor d. W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 volt AC electrical cord coul[...]

Follow the shift pattern on the gearshift knob. NOTE: The backup lights will come on when your vehicle is in R (Reverse) gear and the ignition is in the ON position. W ARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage.[...]

• Do not operate at sustained high engine or road speeds in lower gears. Engine damage may result. • Do not downshift into a low gear while traveling at too high a speed for that gear . Engine, clutch, or transmis- sion damage may result. • Do not rest your foot on the clutch pedal. This causes heat buildup and damages the clutch. • When yo[...]

Recommended Manual T ransmission Downshifting Speeds T o prevent clutch and transmission damage, your vehicle should be downshifted at speeds no greater than those listed in the chart below: Manual T ransmission Downshift Speeds in MPH (KM/H) Gear Selec- tion 6th to 5th 5th to 4th 4th to 3rd 3rd to 2nd 2nd to 1st Maxi- mum Speed 100 mph (160 km/h) [...]

AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P (Park) only after the vehicle has come to a complete stop. • Shift into or out of R (Reverse) only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from R (Reverse),[...]

Shift Lock Manual Override — If Equipped Y our vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from Park with the key in the ON position and the brake pedal depressed. T o operate the shift lock manual override, perform the following steps: 1. Firmly [...]

Brake/T ransmission Interlock System This system prevents you fr om moving the gear shift out of P (Park) and into any gear unless the brake pedal is pressed. Always depress the brake pedal first, before moving the gear selector out of P (Park). 4–Speed Automatic T ransmission (3.7L Engine) Shifting from D (Drive) to P (Park) or R (Reverse) (or f[...]

P (Park) This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in P (Park) position. W ARNING! Never use P (Park[...]

R (Reverse) Use this range only after the vehicle has come to a complete stop. N (Neutral) Shift into N (Neutral) when the vehicle is standing for prolonged periods with the engine r unning. The engine may be started in this range. Set the parking brake if you must leave the vehicle. NOTE: T owing the vehicle, coasting, or driving for any other rea[...]

• the transmission selector is in D (Drive); • the engine coolant has reached normal operating tem- perature; • vehicle speed is above approximately 30 mph (48 km/h); • the “TOW/HAUL” button has not been activated; • transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratur[...]

operating in “TOW/HAUL” mode, the transmission will shift to 3rd gear and 4th will be enabled under steady cruise conditions. The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time r estores normal operation. If the “TOW/HAUL” mode is des[...]

T o reset the transmission, use the following pr ocedure: 1. Stop the vehicle. 2. Move the shift lever to the P (Park) position. 3. T urn off the engine, be sur e to turn the key to the LOCK position. 4. W ait approximately 10 seconds, then r estart the en- gine. 5. Move the shift lever to the desir ed gear range. If the problem is no longer detect[...]

Gear Ranges NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. If there is a need to r estart the engine be sure to cycle the key to the LOCK position before r estarting. T ransmission gear engagement may be delayed after restarting the [...]

W ARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is id[...]

of the desired top gear . For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear , but can shift down to 2 (second) or 1 (first), when needed. W ARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle coul[...]

risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section. During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature. This featur e improves the warm up time of the engine and transmission. During cold temperature operation, the transmission may n[...]

A clutch within the torque converter engages automati- cally at a calibrated speed at light throttle. It engages at higher speeds under heavier acceleration. This may re- sult in a slightly differ ent feeling or response during normal operation in high gear . When the vehicle speed drops below a calibrated speed, or during acceleration, the clutch [...]

This electronically shifted transfer case pr ovides 2 mode positions: 2 (rear) wheel drive high range (2WD) and 4 wheel drive high range (4WD LOCK). The electronically shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) for normal street and highway conditions (dry har d surfaced roads). When additional traction is re[...]

Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence in tire size can cause damage to the transfer case. Since 4 wheel drive provides impr oved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. Shifting [...]

NOTE: Delayed shifting out of 4WD LOCK may be experienced due to uneven tire wear , low tire pr essure, or excessive loading. MP 140 Single-Speed Full-T ime T ransfer Case — If Equipped Operating Information/Precautions The MP 140 is a single speed (HI range only) transfer case which provides convenient full-time all-wheel drive. No driver intera[...]

P ARKING BRAKE T o set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake W arning Light” in the instru- ment cluster will light. T o release the parking brake, pull up slightly , press the center button, then lower the lever completely . NOTE: The instrument cluster ?[...]

Be sure the parking brake is firmly set when parked, and the gear shift lever is in the P (Park) position (automatic transmission) or R (Reverse) or 1st gear (manual trans- mission). When parking on a hill, you should apply the parking brake before placing the gear shift lever in P (Park), otherwise the load on the transmission locking mechanism ma[...]

When parking on a hill, turn the front wheels towar d the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking[...]

W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop. W ARNING! • The Anti-Lock Brake System (ABS) cannot pre- vent the natural laws of physics from acting on the vehicle, nor ca[...]

CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or tele- phones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is function[...]

build up between the tire tr ead and the road. This hydroplaning action can cause loss of traction, braking ability , and control. • After going through deep water or a car wash, brakes may become wet, resulting in decr eased performance and unpredictable braking action. Dry the brakes by gentle, intermittent pedal action while driving at very sl[...]

CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur . TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric [...]

• European Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tir e size designation. Example: 215/65R15 96H • L T (Light T ruck)-Metric tire sizing is based on U.S. design standards. T[...]

EXAMPLE: 31 = Overall Diameter in Inches (in) 215 = Section W idth in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.5 = Section W idth in Inches (in) R = Construction Code — ⬙ R ⬙ means Radial Construction. — ⬙ D ⬙ means Diagonal or Bias Construction. 15 = Rim Diameter in Inche[...]

EXAMPLE: —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions. (i.e. tire pr essure, vehicle loading, r oad conditions, and posted speed limits). Load Identification: ⴖ ....blank.... ⴖ = Absence of any text on sidewall of the tire indicates a Standar d Load (SL) T ire Extra Load ([...]

EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of T ransportation —This symbol certifies that the tire is in compliance with the U.S. Department of T ransportation tire safety standards, and is appr oved for highway use. MA = Code repr esenting the tire manufacturing location. (2 digits) L9 = Code repr esenting the tire size. (2 digits) ABCD = Cod[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the[...]

3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size, and[...]

passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and car go being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicl[...]

ST ARTING AND OPERA TING 277 5[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory [...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation also increases tire r olling resistance and r esults in higher fuel consump- tion. 3. Ride Comfort and V ehicle Stabilit[...]

check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which cou[...]

Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important. Increased tir e pressur e and reduced vehicle loading may be requir ed for h[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. T read Wear Indicators T [...]

Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose con[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can cause unpredictable handling and stress to steeri[...]

Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . TIRE CHAINS Use “Class S” chains or other traction aids that meet SAE T ype “S” specifications. NOTE: Chains must be the proper size for the vehic[...]

These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es. NOTE: The use of class “S” chains is permitted with P235/65R17 tires. CAUTION! Do not use tire chains on vehicles equipped with tires other than P235/65R17 tires. There may not be adequate clearan[...]

NOTE: The Premium T ire Pr essure Monitor System will automatically locate the pressur e values displayed in the correct vehicle position following a tir e rotation. The suggested rotation method is the “forwar d-cross” shown in the following diagram. TIRE PRESSURE MONITORING SYSTEM (TPMS) — IF EQUIPPED The T ire Pressur e Monitoring System ([...]

The TPM System will warn the driver of a low tire pressur e if the tire pr essure falls below the low pressur e warning threshold for any r eason, including low tem- perature ef fects. The TPM System will continue to warn the driver of low tire pr essure as long as the condition exists, and will not turn off until the tir e pressur e is at or above[...]

CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage. [...]

Under-inflation also r educes fuel efficiency and tir e tread life, and may af fect the vehicle’s handling and stopping ability . • The TPMS is not a substitute for proper tir e mainte- nance, and it is the driver ’s responsibility to maintain correct tir e pressur e, even if under-inflation has not reached the level to trigger illumination o[...]

system will automatically update and the “T ire Pressur e Monitoring T elltale Light” will extinguish once the up- dated tire pr essures have been r eceived. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. A low spare tire will not cause the “T ire Pressur e Monitoring T elltale Light[...]

NOTE: It is particularly important, for you to check the tire pr essure in all of your tir es regularly and to maintain the proper pr essure. The TPMS consists of the following components: • Receiver Module • 4 T ire Pressur e Monitoring Sensors • 3 T rigger Modules (mounted in three of the four wheel wells) • V arious T ire Pr essure Monit[...]

NOTE: Y our system can be set to display pressur e units in PSI, kP A or BAR. NOTE: A low spar e tire will not cause the “T ire Pressur e Monitoring T elltale Light” to illuminate or the chime to sound. Should a low tire condition occur on any of the four active road tir e(s), you should stop as soon as possible, and inflate the low tire(s) tha[...]

by a graphic display , with “- -“ in place of the pressure value(s) indicating which T ire Pressur e Monitoring Sen- sor(s) is not being received. NOTE: Y our system can be set to display pressur e units in PSI, kP A or BAR. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no[...]

However , driving the vehicle for up to 10 minutes above 15 mph (24 km/h) will display a “CHECK TPM SYS- TEM” text message on the EVIC. This text message will then be followed by a graphic display , with “- -“ in place of the flashing low pressur e value. For every subsequent key cycle, the “T ire Pressur e Monitoring T elltale Light” w[...]

FUEL REQUIREMENTS 3.7L Engine (If Equipped) The 3.7L engine is designed to meet all emissions regulations and pr ovide excel- lent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not r ecom- mended. Under normal conditions, the use of premium gasoline[...]

Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the W orld- wide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer r ecom- mends the use of gasoline that meets the WWFC speci- fications if they a[...]

manufacturer . While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Metha- nol. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT . [...]

• An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may requir e immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now bei[...]

the vehicle is raised. Have any abnormal conditions repair ed promptly . Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel[...]

CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the MIL (Malfunction Indica- tor Light) to illuminate, due to fuel vapors escaping from the system. CAUTION! A poorly[...]

NOTE: T ighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly , the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. W ARNING! A fire may result if gasoline is pumped into a portable contai[...]

W ARNING! • Never add fuel when the engine is running. • Never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled. VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s [...]

Each axle GA WR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily incr ease the vehi- cle’s GVWR. T ire Size The tire size on the Label r epresents the actual[...]

or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from fr ont to rear or r ear to front as appropriate until the specified weight limitations are met. Stor e the heavier items down low and be sure that the weight is distributed equally . Stow all loose items securely before driving. Impro[...]

Common T owing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross V ehicle W eight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the [...]

Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and r ear axles. Distribute the load over the front and r ear axles evenly . Make sure that you do not exceed either front or rear GA WR. W ARNING! It is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if eithe[...]

W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They ar e typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufactur ers’ directions, it provides for a mor e level ride,[...]

W eight Distributing Hitch System Improper Adjustment of W eight Distributing System ST ARTING AND OPERA TING 309 5[...]

T railer Hitch Classification Y our vehicle is capable of towing trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package. See your dealer for package content. The[...]

Engine/ T ransmission Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) T ongue Wt. (See Note) 3.7L/6-Speed Manual 4x2 8,500 lbs (3 855 kg) 40 Sq. Ft. (3.72 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.7L/6-Speed Manual 4x4 8,750 lbs (3 969 kg) 40 Sq. Ft. (3.72 square meters) 3,500 lbs (1 587 kg) 350 lbs [...]

4.0L/ Automatic 4x4 7,400 lbs ( 3 356 kg) 32 Sq. Ft. (2.97 square meters) 2,000 lbs (907 kg) 200 lbs (91 kg) 4.0L/ Automatic w/ Cooler 4x2 9,850 lbs (4 468 kg) 64 Sq. Ft. (5.94 square meters) 3,500 lbs (1 588 kg) 350 lbs (159 kg) 4.0L/ Automatic w/ Cooler 4x4 10,100 lbs (4 581 kg) 64 Sq. Ft. (5.94 square meters) 3,500 lbs (1 588 kg) 350 lbs (159 kg[...]

Engine/ T ransmission Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) T ongue Wt. (See Note) 3.7L/ Automatic w/ Cooler 4x2 9,850 lbs (4 468 kg) 64 Sq. Ft. (5.94 square meters) 5,000 lbs (2 268 kg) 500 lbs (227 kg) 3.7L/ Automatic w/Cooler 4x4 10,100 lbs (4 581 kg) 64 Sq. Ft. (5.94 square meters) 5,000 lbs (2 268 [...]

T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehic[...]

NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the T ire and Loading Information plac- ard in the T ire Safety Information section of this manual for the maximum[...]

W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou[...]

3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requir ement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tir e inflation pressur es are e[...]

− T railer brakes are r ecommended for trailers over 1,000 lbs (454 kg) and requir ed for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brak[...]

NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic.[...]

If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while [...]

T owing T ips — Cooling System T o reduce potential for engine and transmission over - heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning T urn off temporarily . − refer to Cooling System [...]

[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................. 3 2 4 䡵 If Y our Engine Overheats ................. 3 2 5 䡵 Jacking And T ire Changing ................ 3 2 6 ▫ Jack Location ........................ 3 2 6 ▫ Spare T ire Stowage .................... 3 2 7 ▫ Spare T ire Removal .................... 3 2 8 ?[...]

HAZARD W ARNING FLASHERS Y our vehicle’s hazard warning flasher is an emer gency warning system. When you activate it, all front and r ear directional signals will flash intermittently . Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not[...]

IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appr opriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There ar e steps that you can take to slow down an imp[...]

JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack i[...]

Spare Tire Stowage The spare tir e is stowed under the rear of the vehicle by means of a cable winch mechanism. T o remove or stow the spare, use the jack handle to r otate the “spare tir e drive” nut. The nut is located under a plastic cover at the center-r ear of the cargo floor ar ea, just inside the liftgate opening. W ARNING! Do not use po[...]

Spare Tire Removal Fit the jack handle extension over the drive nut. Use the Lug W rench to r otate the nut counter clockwise until the spare is on the gr ound with enough slack in the cable to allow to pull the tire out fr om under the vehicle. CAUTION! The winch mechanism is designed for use with the jack extension tube only . Use of an air wrenc[...]

• T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site of the jacking position. For example, if changing the right front tir e, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove spar e tire. 2. Loosen ([...]

4. Locate the jack as shown. For the fr ont tires, place it in the notch on the body weld seam behind wheel to be changed. For the rear tir es, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack scr [...]

W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spar e wheel/tire on the vehicle and install lug nuts with cone-shaped end toward wheel. [...]

JUMP ST ARTING W ARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or cloth- ing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the con- taminated area immediately with large quantities of water . • A batte[...]

4. Connect one end of a jumper cable to the positive terminal of the booster battery . Connect the other end of the same cable to the positive terminal of the discharged battery . W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 5. Connect the other cable, first to th[...]

W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to pre[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L ............... 3 3 8 䡵 Engine Compartment – 4.0L ............... 3 3 9 䡵 Onboard Diagnostic System — OBD II ........ 3 4 0 ▫ Loose Fuel Filler Cap Message ............ 3 4 0 䡵 Emissions Inspection And Maintenance Programs ............................ 3 4 1 䡵 Replaceme[...]

▫ Air Conditioner Maintenance ............. 3 5 1 ▫ Power Steering Fluid Check .............. 3 5 2 ▫ Driveline And Steering Component Lubrication .......................... 3 5 3 ▫ Body Lubrication ..................... 3 5 3 ▫ W indshield W iper Blades ................ 3 5 4 ▫ W indshield W ashers ................... 3 5 4 ▫ Exhaust[...]

▫ Rear T ail, Stop, T urn Signal, And Back-Up Lights ....................... 3 8 1 ▫ Center High Mounted Stop Light (CHMSL) . . . 381 䡵 Fluid Capacities ........................ 3 8 2 䡵 Fluids, Lubricants And Genuine Parts ........ 3 8 3 ▫ Engine ............................. 3 8 3 ▫ Chassis ............................ 3 8 4 MAINT AINI[...]

ENGINE COMP ARTMENT – 3.7L 338 MAINT AINING YOUR VEHICLE[...]

ENGINE COMP ARTMENT – 4.0L MAINT AINING YOUR VEHICLE 339 7[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Pr ess the odometer reset button to turn the message of f. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a r ow , the system will t[...]

4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Appr oximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn of f the ignition key or start the engine. This means that y[...]

DEALER SERVICE Y our dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner . Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pr ocedure yourself. NOTE: Intentional tampering with emissions [...]

Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Always maintain the oil level within the SAFE zone on the dipstick. Adding one quart of oil when the reading is at the bottom of the SAFE zone will result in a r eading at the top of the safe zone on these engines. CAUTION! Overfilling or und[...]

• More than 50% of your driving is at sustained high speeds during hot weather , above 90°F (32°C) • T axi, Police, or delivery service (commercial service) • T railer towing • If equipped for and operating with E–85 (ethanol) fuel If ANY of these apply to you, then change your engine oil at every interval shown in schedule “B” of t[...]

Engine Oil V iscosity (3.7L Engine) SAE 5W -20 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- ture starting and vehicle fuel economy . Y our engine oil filler cap shows the recommended engine oil viscosity for your vehicle. Lubricants which do not have both, the engine oil certi- fication mark and th[...]

Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter . Use a filter of this type for replace- ment. The quality of replacement filters varies consider - ably . Only high quality filters should be used to assure most efficient service. Mopar 威 engine oil filters ar e high quality oil filters a[...]

Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assur e prop[...]

W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual situations involving grossly malfunctioning engine o[...]

Crankcase Emission Control System Proper operation of this system depends on fr eedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly , replace it with a new valve. DO NOT A TTEMPT TO CLEAN THE OLD PCV V AL VE! Check ventilation hose for [...]

Maintenance-Free Battery Y our vehicle is equipped with a maintenance-free battery . Y ou will never have to add water , nor is periodic main- tenance requir ed. W ARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery . CAUTION! It is essential when replacing the ca[...]

W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the W arranty Information B[...]

W ARNING! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid from all sur[...]

amount of a high quality lubricant such as Mopar 威 Lock Cylinder Lubricant directly into the lock cylinder . Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner . This will remove accumula- tions of salt or road film. Operation of the wipers[...]

Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect t[...]

garden hose vertically down the face of the A/C con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber , cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator . Inspect the entire system for leaks. W ith the engine at normal operating temperat[...]

CAUTION! • Mixing of antifreeze/coolant other than the speci- fied HOA T antifreeze/coolant may result in de- creased corrosion protection and engine damage. If a non-HOA T antifreeze/coolant is introduced into the cooling system in an emergency , it should be replaced with the specified antifreeze/coolant as soon as possible. • Do not use plai[...]

Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion pr otection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of pr otection against freezing ac- cor[...]

children, do not stor e ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately . Clean up any ground spills im- mediately . Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is ade[...]

coolant needs to be added, contents of coolant recov- ery bottle must also be protected against fr eezing. • If frequent antifr eeze/coolant additions are r equired, or if the level in the recovery bottle does not dr op when the engine cools, the cooling system should be pressur e tested for leaks. • Maintain antifreeze/coolant concentration at[...]

are pr esent. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Brake System In order to assur e brake system performance, all brake system components should be inspected periodically . Refer to the appropriate “Maintenance Schedule” in Section 8 for suggested service intervals. W ARNI[...]

W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately . Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the BRAKE warning lig[...]

Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter . Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result. Automatic T ransmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmissio[...]

Fluid Level Check — W5A580 (4.0L Engine) Y our vehicle is equipped with a capped dipstick tube, it is sealed and should not be tampered with. Y our autho- rized dealer has the proper tools to ensur e that the fluid level is set properly . Special Additives The manufacturer str ongly recommends against the ad- dition of any additives to the transm[...]

Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water . If con- taminated with water , the fluid should be changed im- mediately . T ransfer Case Fluid Leve[...]

CAUTION! When replacing plugs, do not overtighten. Y ou could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s r ecommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Front/Rear Axle Fluid Fluid Level Check Lubricant should be at bottom edge of the oil fill hole. Adding Fluid Ad[...]

The following maintenance recommendations will enable you to obtain maximum benefit from the corr osion resistance built into your vehicle. What Causes Corrosion? Corrosion is the r esult of deterioration or removal of paint and protective coatings fr om your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • St[...]

CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the under carriage at least once a month. • It is important that the drain holes in the lower edges of the [...]

heavy soil, use Mopar 威 Wheel Cleaner or select a non- abrasive, non-acidic cleaner . Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mo- par 威 cleaners are r ecommended. Do not use oven cleaner . A void automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ pr otective finish[...]

W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar 威 Glass Cleaner or any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use cauti[...]

Replace the belts if they appear frayed or worn or if the buckles do not work properly . FUSES (INTEGRA TED POWER MODULE) The T otally Integrated Power Module (TIPM) is located in the engine compartment near the battery . This center contains cartridge fuses, mini fuses and relays. A label that identifies each component is printed on the inside of [...]

Cavity Cartridge Fuse Mini Fuse Description J1 40 Amp Green Power Folding Seat J2 30 Amp Pink T ransfer Case/Pwr Liftgate Module J3 40 Amp Green Rear Door Module (RR DOOR NODE) J4 25 Amp Natural Driver Door Node J5 25 Amp Natural Passenger Door Node J6 40 Amp Green Anti-Lock Brake Sys- tem (ABS) Pump/ESP J7 30 Amp Pink Anti-Lock Brake Sys- tem (ABS[...]

Cavity Cartridge Fuse Mini Fuse Description J19 60 Amp Y ellow Radiator Fan J20 30 Amp Pink Front W iper LO/HI J21 20 Amp Y ellow Front/Rear W asher J22 25 Amp Natural Sunroof Module M1 20 Amp Y ellow Center High Mounted Stop Light (CHMSL)/ Brake Switch M2 20 Amp Y ellow T railer Lighting M3 20 Amp Y ellow Frt/Rear Axle Lockers M4 10 Amp Red T rail[...]

Cavity Cartridge Fuse Mini Fuse Description M10 20 Amp Y ellow Ignition Off Draw — V ehicle Entertainment System (IOD-VES), Satellite Digital Audio Receiver (SDARS), DVD, Hands Free Module (HFM), RA- DIO, Antenna (ANT), Universal Garage Door Opener (UGDO), V anity Lamp (V ANITY LP) M1 1 10 Amp Red (Ignition Off Draw) IOD-HV AC/A TC, MW SENSR, Und[...]

Cavity Cartridge Fuse Mini Fuse Description M15 20 Amp Y ellow COL MOD, IR SNS, Heater V entilation, Air Conditioning/ Automatic T empera- ture Contr ol (HV AC/ A TC), Rear V iew Mirror (RR VW MIR), Cabin Compartment Node (CCN), T ransfer Case Switch (T -CASE SW), RUN/ST , Multi- Function Control Switch (MUL TIFTCN SW), T ire Pressur e Monitor (TPM[...]

Cavity Cartridge Fuse Mini Fuse Description M21 20 Amp Y ellow Auto Shut Down (ASD #3) M22 10 Amp Red Right Horn (R T HORN (HI/LOW) M23 10 Amp Red Left Horn (L T HORN (HI/LOW) M24 25 Amp Natural Rear W iper (REAR WIPER) M25 20 Amp Y ellow Fuel Pump (FUEL PUMP), Diesel Lift Pump (DSL LIFT PUMP) — Export Only M26 10 Amp Red Power Mirror Switch (PWR[...]

Cavity Cartridge Fuse Mini Fuse Description M33 10 Amp Red Next Generation Con- troller (NGC), Global Powertrain Engine Controller (GPEC) M34 10 Amp Red Park Assist (PRK ASST), Heater V enti- lation, Air Condition- ing Module (HV AC MOD), Headlamp W ash (HDLP W ASH), Compass (COMP AS) M35 10 Amp Red Heated Mirrors M36 20 Amp Y ellow Power Outlet #3[...]

CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the [...]

BULB REPLACEMENT Head Light 1. Open the hood. 2. Reach behind the headlamp unit in the engine com- partment to access the headlamp bulb lock ring. 3. Firmly grasp the lock ring on the back of the headlamp unit housing. 4. Rotate the lock ring on the back of the headlamp housing counter-clockwise to unlock it. CAUTION! Do not touch the new bulb with[...]

4. Disconnect the electrical connector and r eplace the bulb. Front Side Marker 1. Open the hood. 2. Remove the grille assembly , as follows: a. Remove eight fasteners. b. Remove two scr ews from each headlamp. c. Remove two scrivets fr om the center of the grille. d. Remove one push pin fr om the top of each fender . e. Pull the grille assembly to[...]

Rear T ail, Stop, T urn Signal, and Back-Up Lights 1. Open the lift gate. 2. Remove the two push pins. 3. Pull lamp straight back and disconnect electrical con- nection. 4. Remove the two scr ews attaching the backplate to the lamp assembly . 5. Pull the backplate straight back fr om the lamp hous- ing. 6. Disconnect the electrical connector . 7. R[...]

FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 19.5 Gallons 73.8 Liters Engine Oil with Filter 3.7 Liter Engine (SAE 5W -20, API Certified Engine Oil) 5 Qts 4.7 Liters 4.0 Liter Engine (SAE 10W -30, API Certified Engine Oil) 6 Qts 5.7 Liters Cooling System * 3.7 Liter Engine (Mopar 威 Antifreeze/Engine Coolant 5 Y ear/ 100,000 Mile Formula) 14 Q[...]

FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil (3.7L Engine) Use SAE 5W -20, API Certified, meeting material standar d MS-6395 or equiva- lent. Engine Oil (4.0L[...]

Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar 威 A TF+4, Automatic T ransmission Fluid. Manual T ransmission Mopar 威 Manual T ransmission Lubricant or equivalent (meeting the re- quirements of DaimlerChrysler Material Standar d MS-9224) T ransfer Case Mopar 威 A TF+4, Automatic T ransmission Fluid. Front [...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 8 6 䡵 Maintenance Schedules ................... 3 8 6 ▫ Schedule “B” ........................ 3 8 9 ▫ Schedule “A” ........................ 4 0 3 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliab[...]

• Off-r oad or desert driving NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “Schedule B” of the “Maintenance Schedules” section of this manual. NOTE: If ANY of these apply to you then flush and replace your engine coolant/anti-fr eeze every 102,000[...]

Once a Month • Check the tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of the coolant reservoir , brake master cylinder , and transmission, and add as needed. • Check all lights and all other electrical items for correct operation. At Each[...]

Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sus[...]

Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle fluid. X Inspec[...]

Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs[...]

Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle fluid. X In[...]

Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plug[...]

Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Drain and refill the transfer case fluid. X Flush and replace the engine coolant/anti-fr eeze. X 394 SCHEDULE “B” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Inspect the transfer case fluid, add if necess[...]

Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark [...]

Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs (4.0L Only). X Inspect the timing belt, replace if [...]

Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace t[...]

Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Drain and refill the transfer case fluid. X Flush and replace the engine coolant/anti-fr eeze, if not replaced at 102,000 miles (170 000 km). X SCHEDULE “B” 399 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle f[...]

Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spa[...]

Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. † Applies only if vehicle is used for frequent trailer towing or fleet/commercial service. 〫 This maintenance is recommended by the manufac- turer to the owner , but is not requir ed to maintain emissions warranty . ‡Off-high[...]

Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X X X X Inspect the engine air filter element, and replace if necessary . X Replace the spark plugs (3.7L Only). X Inspect the[...]

Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the brake linings. X X 404 SCHEDULE “A” 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (110 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs (3.7L[...]

Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs [...]

Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Inspect the manual transmission fluid, add as necessary (3.7L Only). X Inspect the transfer case fluid, add as necessary . X SCHEDULE “A” 407 8 M A I N T E N A N C E S C H E D U L E S[...]

Miles 108,000 1 14,000 120,000 126,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [108] [1 14] [120] [126] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark p[...]

Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark p[...]

Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Flush and replace the engine coolant/anti-fr eeze, if not done at 120,000 miles (200 000 km). X Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 〫 This ma[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V e h i c l e .............................. 4 1 2 ▫ Prepar e For The Appointment ............ 4 1 2 ▫ Prepar e A List ........................ 4 1 2 ▫ Be Reasonable W ith Requests ............. 4 1 2 䡵 If Y ou Need Assistance ................... 4 1 2[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the deale[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the U[...]

W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SA[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is required when or dering manuals. (No P .O. Boxes). •[...]

Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .daimlerchrysler .com • www .daimlerchrysler .ca/manuals DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the Nationa[...]

on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor - mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. T emperature Grades The temperature [...]

INDEX 10[...]

ABS (Anti-Lock Brake System) ............ 169,265 Adding Fuel ........................... 3 0 0 Adding W asher Fluid ..................... 1 5 6 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 350 Air Conditioner Maintenance ............... 3 5 1 Air Conditioning ..................... 228,232 Air Conditioning Controls ................. 2 3 2[...]

Autostick ............................. 2 5 6 Auxiliary Electrical Outlet (Power Outlet) ...... 1 4 4 Auxiliary Power Outlet ................... 1 4 4 A x l e F l u i d ............................. 3 8 4 Battery ............................... 3 5 1 Charging ............................ 3 3 2 Emergency Starting ..................... 3 3 2 Gas Caut[...]

C a r g o L i g h t ............................ 1 5 0 Cargo Load Floor ........................ 1 5 1 Cargo Slide Out System L o a d N G o ........................... 1 5 3 Cargo T ie-Downs ........................ 1 5 0 Catalytic Converter ...................... 3 4 8 CD (Compact Disc) Player Maintenance ........ 2 2 7 Cellular Phone ............[...]

Selection of Coolant (Antifreeze) ...... 356,382,383 T emperature Gauge ..................... 1 6 4 Corrosion Pr otection ..................... 3 6 6 Crankcase Emission Control System .......... 3 5 0 C u p H o l d e r ............................ 1 4 7 Customer Assistance ..................... 4 1 2 Data Recorder , Event ...................... 6 1[...]

Emission Control System Maintenance ...... 341,386 Engine Air Cleaner .......................... 3 5 0 Block Heater ......................... 2 4 3 Break-In Recommendations ................ 7 4 Compartment ...................... 338,339 Compartment Identification ............ 338,339 Coolant (Antifreeze) .................... 3 8 3 Exhaust Gas Cauti[...]

Flooded Engine Starting ................... 2 4 0 Fluid, Brake ........................... 3 8 4 Fluid Capacities ......................... 3 8 2 Fluid Leaks ............................. 7 6 Fluid Level Checks ...................... 3 6 6 Automatic T ransmission ................. 3 6 3 Engine Oil ........................... 3 4 3 Manual T ransmiss[...]

Gauges Coolant T emperature .................... 1 6 4 Fuel ................................ 1 6 4 Odometer ........................... 1 7 2 Speedometer ......................... 1 6 6 T achometer .......................... 1 7 0 Gear Ranges ...................... 245,249,255 General Information .................... 1 9 , 2 9 5 Glass Cleaning ....[...]

Inflation Pressur e T ires .................... 2 7 9 Information Center , V ehicle ................. 1 7 9 Inside Rearview Mirror .................... 8 1 Instrument Cluster .................... 163,164 Instrument Panel and Contr ols .............. 1 6 2 Instrument Panel Lens Cleaning ............. 3 7 0 Integrated Power Module (Fuses) ...........[...]

Bulb Replacement ................... 378,379 C a r g o .............................. 1 5 0 Center Mounted Stop ................... 3 8 1 C r u i s e .............................. 1 7 4 Daytime Running ...................... 1 2 2 Dimmer Switch, Headlight ............... 1 2 0 Electronic Stability Pr ogram (ESP) Indicator ....................... 1[...]

Lower Anchors and T ether for CHildren (LA TCH) ................... 6 8 , 6 9 Lubrication, Body ....................... 3 5 3 Luggage Carrier ......................... 1 5 7 Maintenance Free Battery .................. 3 5 1 Maintenance Procedur es ................... 3 4 3 Maintenance Schedule .................... 3 8 6 Schedule “A” ...........[...]

Odometer T r i p ................................ 1 7 4 Oil, Engine ......................... 343,383 Capacity ............................ 3 8 2 Dipstick ............................. 3 4 3 F i l t e r ............................ 346,383 Identification Logo ..................... 3 4 5 Materials Added to ..................... 3 4 6 Recommendation [...]

Sunroof ............................. 1 4 1 W indows ............................. 3 1 Power Steering Fluid ..................... 3 8 4 Pregnant W omen and Seat Belts .............. 4 5 Preparation for Jacking .................... 3 2 8 Pretensioners Seat Belts ............................. 4 4 Programmable Electr onic Features ...... 136,140,188 P[...]

Rotation, T ires .......................... 2 8 6 Safety Checks Inside V ehicle ................. 7 5 Safety Checks Outside V ehicle ............... 7 6 Safety Defects, Reporting .................. 4 1 5 Safety Information, T ire ................... 2 6 9 Safety T ips ............................. 7 4 Satellite Radio ....................... 219,221[...]

Settings, Personal ........................ 1 8 8 Shift Lock Manual Override ................ 2 4 8 Shift Speeds, Manual T ransmission ........... 2 4 5 Shifting Automatic T ransmission ............... 249,254 Manual T ransmission ................... 2 4 3 Shoulder Belts ........................... 3 8 Signals, T urn ................... 121,167,379[...]

System, Navigation ...................... 2 1 9 System, Remote Starting .................... 2 6 T able, Utility ........................... 1 5 2 T achometer ............................ 1 7 0 T emperature Gauge, Engine Coolant .......... 1 6 4 T ether Anchor , Child Restraint ............... 6 8 T ie Down Hooks, Cargo ................... 1 5 0 T [...]

Disabled V ehicle ....................... 3 3 4 G u i d e .............................. 3 1 0 Recreational .......................... 3 2 1 W e i g h t .............................. 3 1 0 T raction Control ...................... 129,169 T r a i l e r T o w i n g .......................... 3 0 5 Cooling System T ips .................... 3 2 1 Hitc[...]

Universal T ransmitter ..................... 1 3 4 Upholstery Care ........................ 3 6 9 Utility T able ........................... 1 5 2 V acuum/V apor Harnesses ................. 3 6 0 V a n i t y M i r r o r s ........................... 8 4 V ariance, Compass .................... 177,184 V ehicle Identification Number (VIN) ...........[...]