Dukane 8760 manuel d'utilisation

Por table Projector 8760/8761 About this user's manual The fastest way to get started is to take your time and do ever y- thing right the first time. T ake a few minutes now to review the user's manual. This may save you time later on. At the begin- ning of each section of the manual you'll find an over view . If the section doesn&ap[...]

E-2 Introduction to the Pr ojector INTRODUCTION This section introduces y ou to y our n e w 8760/8761 Projector and describes the features and controls . Congratulations on Y our Pu r chase of The 8760 / 8761 P r ojector The 8760/8761 is one of the v e r y best projectors a v aila b le tod a y . The 8760/8761 ena b les y ou to project precise image[...]

E-3 INTRODUCTION ⬎ Introduction to the Projector • Saf ety protect by P assword and Security functions P assw ord and Secur ity features pre vent the projector from being used by unauthorized individuals. P assword pre vents unauthoriz ed individuals from changing projector settings or adjustments. Security offers complete protection b y using [...]

E-4 NO TE: Composite video standards are as follows: NTSC: U.S. TV standar d for video in U.S. and Canada. P AL: TV standar d used in W estern Eur ope. P AL-N: TV standar d used in Ar gentine, P ara guay and Uruguay . P AL-M: TV standar d used in Brazil. P AL60: TV standar d used for NTSC playback on P AL TVs. SECAM: TV standar d used in Fr ance an[...]

E-5 • The supplied remote control can be used without a cab le, and y ou can e ven use the remote control to operate y our PC's mouse wirelessly from across the room with the b uilt-in remote mouse function. •Y ou can control the projector with a PC using the PC Control por t. • USB por t allows USB mouse operation* 4 . * 4 The USB por t[...]

E-6 Part Names of the Pr ojector S E L E C T C N A C E L T E R N E E M N U S O U R C E A U T O A D J U S T O N S T A N D B Y STATUS POWER LAMP A L I G N M E N T P C -C A R D INTRODUCTION ⬎ Part Names of the Projector V entilation (outlet) Heated air is exhausted from here * This security slot suppor ts the MicroSa ver ® Security System. MicroSav[...]

E-7 INTRODUCTION ⬎ Part Names of the Projector Monaural Speaker (2W) AC Input Connect the supplied power cab le's three-pin plug here, and plug the other end into an activ e w all outlet. (See page E-35) Main P ower Switch When you plug the supplied po wer cable into an ac- tiv e wall outlet and turn on the Main P ower s witch, the POWER ind[...]

E-8 INTRODUCTION ⬎ Part Names of the Projector 91 0 4 5 1 1 67 8 1 2 1 3 2 T op Features 1.POWER Button (ON / ST AND BY) Use this button to turn the power on and off when the main po wer is supplied and the projector is in standby mode . NO TE: T o turn on or off the pr ojector , pr ess and hold this button for a mini- mum of two seconds. 2. ST A[...]

E-9 INTRODUCTION ⬎ Part Names of the Projector ⬎ T op Features 4. SOURCE Button Use this button to select a video source such as a PC , VCR, D VD pla yer , Viewer (PC card), or LAN. Press and release this button quic kly to display the Source List. Each time this button is pressed f or a minimum of ONE second, the input source will change as f [...]

E-10  : Use these b uttons to change the lev el of a selected menu item. A press of the  b utton ex ecutes the selection. When the menus or the Viewer tool bar is not displa yed, these buttons can be used to select a slide, or to mo ve the cursor in F older List or Slide List. When the pointer is displa yed, these  b uttons mo [...]

E-11 INTRODUCTION ⬎ Part Names of the Projector ⬎ T erminal Panel Features 10 11 3 5 4 2 1 6 7 8 9 12 13 T erminal Panel Features 1. RGB IN 1 / Component Input Connector (Mini D-Sub 15 Pin) Connect your computer or other analog RGB equipment such as IBM compatib le or Macintosh computers. Use the supplied RGB cable to connect to your computer .[...]

E-12 INTRODUCTION ⬎ Part Names of the Projector ⬎ T erminal Panel Features 5. A UDIO OUT Mini Jack (Stereo Mini) Connect an additional audio equipment here to listen to audio coming from your computer , Video or S- Video input. Note that there is no audio output from this jac k during Standby and Idle. 6 S-VIDEO IN Connector (Mini DIN 4 Pin) He[...]

E-13 10. USB P or t (T ype A) Connect a commercially av ailable mouse that supports USB. Y ou can operate the menu or Viewer with the USB mouse via this port. Note that this por t should not be connected to a computer and that there may be some br ands of USB mouse that the projector does not suppor t. 11. USB P or t (T ype B) Connect this por t to[...]

E-14 Part Names of the Remote Control M E N U PJ ASPECT OFF VIDEO AUTO ADJ. S-VIDEO RGB1 RGB2 LASER ON 3D REFORM HELP POINTER VOLUME MAGNIFY PICTURE PIC-MUTE VIEWER SLIDE FOLDER SLIDE LIST E N T E R C A N C E L POWER SELECT FREEZE 16 21 19 26 27 28 29 17 20 22 24 25 23 15 14 12 11 10 9 6 8 7 4 5 3 18 13 INTRODUCTION ⬎ Part Names of the Remote Con[...]

E-15 INTRODUCTION ⬎ Part Names of the Remote Control 6. VIDEO Button Press this b utton to select an NTSC , P AL, P AL-N, P AL-M, P AL60, SECAM or NTSC4.43 compatible video source from a VCR, D VD play er , or laser disc pla yer . 7. S-VIDEO Button Press this button to select an S-Video source from a VCR. 8. RGB 1 Button Press this button to sele[...]

E-16 INTRODUCTION ⬎ Part Names of the Remote Control 13. SELECT  (Mouse) Button When y ou are in the Computer mode, these b uttons work as a com- puter mouse. When you are in the Projector mode, which is indicated by lighting the PJ button. See page E-52.  : Use these buttons to select the men u of the item y ou wish to adjust. [...]

E-17 INTRODUCTION ⬎ Part Names of the Remote Control 17. ASPECT Button Press this button to displa y the Aspect Ratio select screen. See page E-86. 18. FREEZE Button This button will freez e a picture. Press again to resume motion. 19. 3D REFORM Button Press this button to enter 3D Ref orm to correct the keystone (trapez oi- dal) distor tion, and[...]

E-18 25. PICTURE MUTE Button This button turns off the image and sound f or a shor t period of time. Press again to restore the image and sound. NO TE: When the menu is displayed, a pr ess of this button mutes an imag e and sound without turning off the menu. 26. VIEWER Button Press this button to select the View er source. 27. SLIDE (+) (–) Butt[...]

E-19 Battery Installation 1. Pr ess the catch and remov e the battery cov er . 2. Remov e both old batteries and install new ones (AA). Ensure that y ou hav e the batteries' polarity (+/-) aligned correctly . 3. Slip the co ver back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries. [...]

E-20 Remote Control Pr ecautions • Handle the remote control carefully . • If the remote control gets wet, wipe it dry immediately . •A v oid excessive heat and humidity . • If you will not be using the remote control f or a long time, remov e the batteries. • Do not place the batteries upside down. • Do not use new and old batteries to[...]

E-21 INST ALLA TION AND CONNECTIONS This section describes how to set up your projector and ho w to connect video and audio sources. 3 1 2 Y our projector is simple to set up and use. But before y ou get star ted, you must first: z Set up a screen and the pr ojector . x Connect your computer or video equipment to the pr ojector . See page E- 27. c [...]

E-22 INST ALLA TION AND CONNECTIONS ⬎ Setting Up the Screen and theProjector 406.4(W) ⳯ 304.8(H)/160"(w) ⳯ 120"(H) 365.8(W) ⳯ 274.3(H)/144"(W) ⳯ 108"(H) 304.8(W) ⳯ 228.6(H)/120"(W) ⳯ 90"(H) 243.8(W) ⳯ 182.9(H)/96"(W) ⳯ 72"(H) 203.2(W) ⳯ 152.4(H)/80"(W) ⳯ 60"(H) 162.6(W) ⳯ 121[...]

E-23 INST ALLA TION AND CONNECTIONS ⬎ Setting Up the Screen and theProjector Distance Chart B = V er tical distance between lens center and screen center C = Throw distance D = V er tical distance between lens center and bottom of screen α = Throw angle Lens Center Throw Angle ( 움 ) Throw Distance (C) Screen center Screen Diagonal Screen Width[...]

E-24 INST ALLA TION AND CONNECTIONS ⬎ Setting Up the Screen and theProjector 8761 B = V er tical distance between lens center and screen center C = Throw distance D = V er tical distance between lens center and bottom of screen α = Throw angle NO TE: Distances may vary +/-5%. α Wide – T ele inch 24 32 48 54 58 64 67 72 80 96 120 144 160 168 1[...]

E-25 INST ALLA TION AND CONNECTIONS ⬎ Setting Up the Screen and theProjector 8760 B = V er tical distance between lens center and screen center C = Throw distance D = V er tical distance between lens center and bottom of screen α = Throw angle NO TE: Distances may vary +/-5%. α Wide – T ele inch 24 32 48 54 58 64 67 72 80 96 120 144 160 168 1[...]

E-26 W ARNING * Installing your projector on the ceiling m ust be done by a qualified tech- nician. Contact y our dealer f or more in f o r mation. * Do not attempt to install the projector yourself . • Only use your projector on a solid, le vel surf ace. If the projector f alls to the ground, you can be injured and the projector se verely damage[...]

E-27 Making Connections INST ALLA TION AND CONNECTIONS VCR, DVD Pla yer or LaserDisc Player Macintosh (Desktop type or notebook type) IBM VGA or Compatib les (Desktop type or notebook type) D VD Player (with component output) Document Camera To video , S-video, and au- dio inputs on the projector . Optional 15-pin-to-RCA (female) ⳯ 3 cable (ADP-C[...]

E-28 INST ALLA TION AND CONNECTIONS ⬎ Making Connections To connect SCART output (RGB) Bef ore connections: An e xclusive SCAR T adapter (ADP-SC1) and a com- mercially a vailab le SCART cab le are required for this connection. NO TE: •A udio signal is not available for this connection. • The RGB IN 2 connector does not support SCART signal an[...]

E-29 INST ALLA TION AND CONNECTIONS ⬎ Making Connections Connecting Y our PC or Macintosh Computer PHONE RGB IN1 RGB IN2 AUDIO IN PHONE A udio cab le (not supplied) IBM V GA or Compatibles (Note- book type) or Macintosh (Note- book type) IBM V GA or Compatibles (Desktop type) or Macintosh (Desktop type) RGB signal cable (supplied) To mini D-Sub 1[...]

E-30 INST ALLA TION AND CONNECTIONS ⬎ Making Connections Connecting your PC or Macintosh computer to y our projector will enable y ou to project y our computer's screen image for an impressiv e presenta- tion. To connect to a PC or Macintosh, simply: 1. T urn off the po wer to your pr ojector and computer . 2. Use the supplied signal cable t[...]

E-31 INST ALLA TION AND CONNECTIONS ⬎ Making Connections RGB OUT Connecting an External Monitor Y ou can connect a separate , e xter nal monitor to y our projector to simulta- neously view on a monitor the RGB analog image y ou're projecting. T o do so: 1. T urn off the po wer to your pr ojector , monitor and computer . 2. Use a 15-pin cable[...]

E-32 INST ALLA TION AND CONNECTIONS ⬎ Making Connections Connecting Y our V ideo Equipment RGB IN1 or IN2 AUDIO OUT RL COMPONENT OUT AUDIO IN LR D VD player Connecting Y our D VD Play er A udio Equipment Optional 15-pin-to-RCA (female) ⳯ 3 cab le (ADP-CV1) A udio cable (not supplied) Y ou can connect your projector to a D VD play er with compon[...]

E-33 INST ALLA TION AND CONNECTIONS ⬎ Making Connections VCR/ Laser disc play er Connecting Y our VCR or Laser Disc Pla yer VIDEO IN S-VIDEO IN AUDIO OUT RL VIDEO OUT S-VIDEO OUT AUDIO IN LR A udio equipment S-video cable (not supplied) Video cable (not supplied) A udio cab le (not supplied) Use common RCA cables (not pro vided) to connect your V[...]

E-34 3. T urn on the pr ojector and the VCR or laser disc play er . NO TE: Refer to your VCR or laser disc player owner's manual for mor e informa- tion about your equipment's video output r equir ements. NO TE: An image may not be displayed corr ectly when a V ideo or S-V ideo source is played back in fast-forwar d or fast-re wind via a [...]

E-35 INST ALLA TION AND CONNECTIONS ⬎ Making Connections Connecting the Supplied Power Cable Connect the supplied power cab le to the projector . First connect the supplied power cab le's three-pin plug to the AC IN of the projector , and then connect the other plug of the supplied pow er cable in the wall outlet.[...]

E-36 PROJECTING AN IMAGE (BASIC OPERA TION) Tu r ning on the Projector This section describes how to turn on the projector and to project a picture onto the screen. NO TE: • When plugging in or unplugging the supplied power cable , make sur e that the main power switch is pushed to the of f[O] position. F ailure to do so may cause damage to the p[...]

E-37 PROJECTING AN IMAGE ⬎ T urning on the Projector Note on Startup scr een (Menu Language Select screen) When you first turn on the projector , you will get the Startup screen. This screen gives y ou the oppor tunity to select one of the se ven men u lan- guages: English, German, French, Italian, Spanish, Sw edish and Japa- nese. To select a me[...]

E-38 3. The Basic menu will be displayed in the language y ou hav e selected. PROJECTING AN IMAGE ⬎ T urning on the Projector M E N U E N T E R C A N C E L SELECT To close the menu, press the CANCEL b utton. After this has been done, y ou can proceed to the advanced men u opera- tion. If you w ant, you can select the menu language later . See &qu[...]

E-39 PROJECTING AN IMAGE Selecting a Sour ce Selecting the computer or video source Using the Remote Control ASPECT OFF VIDEO AUTO ADJ. S-VIDEO RGB1 RGB2 LASER ON 3D REFORM HELP POINTER VOLUME MAGNIFY PICTURE PIC-MUTE VIEWER SLIDE FOLDER SLIDE LIST POWER FREEZE NO TE: If no input signal is available, the pr ojector will display a blue back- gr ound[...]

E-40 Press and hold the SOURCE button f or a minimum of ONE second, the projector will search f or the next a vailable input source . Each time y ou press and hold the SOURCE b utton, the input source will change as f ollows: → RGB1 → RGB2 → Video → S-Video → Viewer  If no input signal is present, the input will be skipped. When the in[...]

E-41 PROJECTING AN IMAGE Adjusting the Pictur e Size and Position Place your projector on a flat le v el surf ace and ensure that the projector is square to the screen. Lift the front edge of the projector to center the image v er tically . Mov e the projector left to center the image horizontally on the screen. Use the 3D REFORM f eature for prope[...]

E-42 Adjust the Tilt Foot q Lift the front edge of the pr ojector . w Push up the Adjustable Tilt Foot Le ver on the front of the pr ojector to extend the adjustable tilt f oot (maximum height). e Push down the Adjustable T ilt Foot Lev er . r Lower the front of the pr ojector to the desired height and r elease the Adjustable Tilt F oot Lever to lo[...]

E-43 The rear f oot height can be changed. Rotate the rear foot to the desired height, but the v er tical distance from the bottom to the desk or floor should be 1" (25 mm) to mak e the projector horizontal on the flat surf ace. * If the projected image does not appear square to the screen then use the 3D Reform f eature for proper adjustment.[...]

E-44 Correcting the Horizontal and V ertical Keystone Distortion (3D Reform) PROJECTING AN IMAGE Screen Projected image Use the 3D Ref orm feature to correct k e ystone (trapez oidal) distor tion to make the top or bottom and the left or right side of the screen longer or shor ter so that the projected image is rectangular . Y ou can also use a mou[...]

E-45 4. Use the SELECT  b utton to select one icon which points in the direction y ou wish to move the pr ojected image frame. PROJECTING AN IMAGE Screen 5. Press the ENTER button. 6. Use the SELECT  b utton to mo ve the projected image frame as shown on the example. 7. Press the ENTER button. Screen 8. Use the SELECT [...]

E-46 PROJECTING AN IMAGE 9. Press the SELECT  or  b utton to highlight the [OK] and press the ENTER button. This completes the ke ystone correction. Selecting “Cancel” will return to the adjustment screen without saving changes (Step 3). Selecting "Reset" will return to the factor y def ault. Selecting "Undo" will e xi[...]

E-47 PROJECTING AN IMAGE Optimizing RGB Pictur e Automatically Adjusting the Image Using Auto Adjust Optimizing RGB image automatically Press the Auto Adjust b utton to optimize an RGB image automatically . [P oor picture] [Normal picture] AUTO ADJ. Press the A uto Adjust b utton to fine-tune the computer image or to remove any v er tical banding t[...]

E-48 PROJECTING AN IMAGE Tu r ning Up or Down V olume Sound le vel from the speak er and the A UDIO OUT mini jack on the projec- tor can be adjusted. increase volume V olume bar decrease volume VOLUME Using the Laser Pointer O F F V I D E O AUTO ADJ. S - V I D E O R G B 1 R G B 2 L A S E R P O W E R O N P J A S P E C T 3 D R E F O R M H E L P P O I[...]

E-49 Setting the function switch ON OFF There are two s witches on the bottom of the batter y case: an applicable projector selector s witch (1) and laser enable/dis- able s witch (2). Chec k the projector be- ing used and decide whether to enab le or disable laser , then set these switches as necessar y using the tip of a thin ball- point pen. On [...]

E-50 PROJECTING AN IMAGE Tu r ning off the Pr ojector To turn off the pr ojector: First press the POWER (ON/ST AND BY) b ut- ton on the projector cabinet or the PO WER OFF b utton on the remote control f or a minimum of two seconds. The power indicator will glo w or- ange. After the projector tur ns off , the cooling f ans keep oper ating for 90 se[...]

E-51 CONVENIENT FEA TURES Using the Remote Mouse Function The b uilt-in remote mouse function enables y ou to operate your computer's mouse functions from the remote control (Computer mode). It is a great conv enience for clic king through your computer-generated presentations . To retur n to the projector operation mode (Projector mode), pres[...]

E-52 CONVENIENT FEA TURES ⬎ Using the Remote Mouse Function Switching operation mode between computer and pr o- jector The three shaded buttons sho wn on the drawing w or k as a computer mouse in the Computer mode. In the Computer mode the PJ button is not lit. M E N U E N T E R C A N C E L PJ FOCUS ZOOM OFF VIDEO AUTO ADJ. S-VIDEO RGB1 RGB2 LASE[...]

E-53 • When the MENU button is pressed, the PJ b utton lights red to indi- cate that you are in the Projector mode , which allows the projector menu operation using the three b uttons. • When the POINTER button is pressed, the PJ b utton lights red to indicate that you are in the Projector mode and that the SELECT  b utton works as [...]

E-54 CONVENIENT FEA TURES Tu r ning Off the Image and Sound Press the Picture Mute button to turn off the image and sound f or a shor t period of time. Press again to restore the image and sound. PIC-MUTE Fr eezing a Picture Press the F reeze b utton to freeze a picture . Press again to resume motion. FREEZE Using the Pr ojector Pointer Y ou can us[...]

E-55 Enlarging and Moving a Picture CONVENIENT FEA TURES Y ou can enlarge the area you w ant up to 400 percent. To do so: 1. Press the P ointer button to display the projector pointer . 2. Move the projector pointer to the ar ea you want to enlar ge. 3. Enlarge the selected area. When the Magnify (+) button is pr essed, the pointer is changed to a [...]

E-56 CONVENIENT FEA TURES Getting the On-line Help Y ou get the contents about Help . Display Help Exit Help HELP SELECT The projector is compatible with either a USB memory device or USB memor y card reader which suppor ts the viewer and security f eatures. •T o use a USB memor y de vice or USB memor y card reader , connect the de vice to the US[...]

E-57 NO TE: • Some USB memory devices (br ands) or USB memory card r eaders may not work. •Y ou cannot use a USB memory device and a USB memory car d reader when connecting a USB mouse to the pr ojector . Using a USB HUB that allows multiple USB memory devices or car d reader s is not supported either . • Do not do the following while the USB[...]

E-58 Using a USB Mouse CONVENIENT FEA TURES Using a USB mouse giv es you a smooth operation. A commercially a vail- able USB mouse is required. USB NO TE: Ther e may be some brands of USB mouse that the pr ojector does not support. Operate the Menus using the USB mouse Mouse Cursor When connecting a USB mouse to the projector , you get a mouse cur-[...]

E-59 Examples Click (or press and hold) the mouse b utton  or  to adjust the bright- ness. Or click and drag the mouse b utton on the slide bar horizontally to adjust it. To sav e the adjustments, click . The displa y is closed. If you clic k anywhere in the bac kground while displa ying adjustment and setting menu or dialog bo x, you will ge[...]

E-60 4. Use the SELECT  and then  button to select "Logo". 5. Press the ENTER on the remote contr ol or the cabinet. Y ou will get the confirmation dialog box. 6. Select "OK" and press the ENTER b utton. This completes changing a logo for the backgr ound. * Once y ou h a v e changed the ba c k g round from the logo to an o[...]

E-61 CONVENIENT FEA TURES Making Fr eehand Drawings on a Projected Image (ChalkBoar d) The ChalkBoard f eature allows y ou to wr ite and draw messages on a pro- jected image. NO TE: The ChalkBoar d feature is available only when a USB mouse is used. F rom the menu, select [T ools] → [ChalkBoard] to display the ChalkBoard tool bar that cotains the[...]

E-62 USING THE VIEWER NO TE: T o use the V iewer , fir st you need to create pr esentation materials on your PC using the Dynamic Ima g e Utility 2.0 contained on the supplied P r ojec tor User Supportwa r e CD- R OM. F or installation, see the printed Application Guide . F or cr eating presentation materials, see the Slide show function on the on-[...]

E-63 Simple utility software (for computer) • Dynamic Image Utility 2.0 operab le on Windows 98/Me/XP/2000 • Slides can be created by capturing the currently displa yed image • Control screen f or displa ying lists of slides and editing *M icrosoft, Windows and P owerP oint are registered trademarks of Microsoft Cor poration. Inserting and Re[...]

E-64 Removing the PC Card Press the eject button. The PC card pops out a little . Grasp the edges of the PC card and pull it out. NO TE: Do not eject the PC car d while its data is being accessed. USING THE VIEWER Dir ection for Inserting the PC Card The PC card has a top and bottom and must be inser ted into the PC card slot in a specific directio[...]

E-65 Operating the V iewer Function fr om the Projector (playback) USING THE VIEWER This section describes the operation f or showing slides of presentation documents created using the View er function with the projector . It is also possible to mak e slides directly from the images projected with the projec- tor . Pr ojecting slides (Viewer) 1. In[...]

E-66 Pla y ............ Pla ys back automatically or manually depending on the setting on Viewer Options of the menu. This allows you to mov e on to the ne xt slide when "Manual Pla y" is selected. Stop ............ This allows you to stop A uto Play while y ou are playing bac k and to resume pla ying from the selected slide or f older wh[...]

E-67 USING THE VIEWER When the tool bar is not displayed: Press the FOLDER LIST b utton or the SLIDE LIST button on the remote con- trol to display f olders or slides from a PC card in the projector's PC Card slot. SLIDE Folder 02 : 0001 / 0008 Folder Folder Folder Folder Multi cursor (blue marks) Current folder number Current slide number Num[...]

E-68 NO TE: Y ou can also use the  and  b utton on the r emote control to select folders or slides. If you use the  and  b utton on the r emote contr ol for V ie wer operation, pr ess the PJ b utton to switch to the Pr ojector mode and the PJ button lights r ed. USING THE VIEWER Lit red W orks as the Select button on the projector . E N[...]

E-69 USING THE VIEWER V iewing Digital Images Digital images can be pla yed with the View er if the f ollowing conditions are met: • If the image can be stored on an MS-DOS f or mat PC card • If the image can be stored in a f or mat suppor ted by the Viewer . With the View er , images on the card are searched f or in director ies and images in [...]

E-70 NO TE: * Unless a PC car d is inserted into the PC Car d slot of the pr ojector , the Cap- tur e feature is not available . * The "Car d Error" display means that the fr ee space of the PC car d is insuff i- cient for saving images. Mak e more space available on the car d by erasing unwanted images with your PC. The number of images [...]

E-71 Exit ............. Exits the Capture function. Another option to exit the Cap- ture function is to press MENU or CANCEL b utton on the remote control or projector cabinet. NO TE: Y ou can compress a captur ed file (JPEG) using the Captur e Options in the Setup dialog. See pa ge E-97. Captur ed images with higher r esolution than the pr ojector[...]

E-72 USING THE VIEWER Deleting Captured Images Using the Delete button on the tool bar f or View er can delete captured images. To delete captured images: 1. Select Viewer and display a f older list of captured images. 2. Use b utton to select the Captur e folder [Cap] in the right bottom of the screen. 3. Press the MENU b utton to display the tool[...]

E-73 USING ON-SCREEN MENU Using the Menus NO TE: The on-scr een menu may not be displayed corr ectly while interlaced mo- tion video image is pr ojected. 1. Press the MENU b utton on the remote contr ol or projector cabinet to display the Basic, Advanced or Custom Menu. NO TE: When using a USB mouse , click the mouse b utton to display the menu. F [...]

E-74 USING ON-SCREEN MENU ⬎ Basic Menu Operation Customizing the Menu The Custom menu can be customiz ed to meet your requirements. Select- ing a menu item from the "Custom Menu Edit" list, allo ws you to custom tailor the menu items to y our needs. 1. Select "Custom Menu Edit" to display the "Custom Menu Edit" scree[...]

E-75 USING ON-SCREEN MENU ⬎ Basic Menu Operation NO TE: If the "Advanced Menu" item has been selected on the Menu mode, you g et the "Conf irmation Change Menu" upon completion of "Custom Menu" edit- ing. In this case , selecting "Y es" then "Enter" will close all the menus and apply the changes f[...]

E-76 USING ON-SCREEN MENU ⬎ Basic Menu Operation Menu tree Brightness, Contrast, Color, Hue, Sharpness 4:3, Letter Box, Wide Screen, Crop / 4:3 Window, Letter Box, Wide Screen, 4:3 Fill Top, Bottom, Left, Right Horizontal, Vertical, Clock, Phase Auto, Native 0%, 5%, 10%, 25% Off, Less, More Off, Low, Medium, High Advanced Menu Source Select Pictu[...]

E-77 USING ON-SCREEN MENU ⬎ Basic Menu Operation Advanced Menu Source Select Picture Volume Image Options Picture Management Projector Options Tools Help Factory Default 3D Reform Menu Setup Screen LAN Mode Password Security Menu Setup Cornerstone Keystone Page 1 Language Menu Mode Projector Pointer Mouse Pointer Menu Display Time English, Deutsc[...]

E-78 Advanced Menu Source Select Picture Volume Image Options Picture Management Projector Options Tools Help Factory Default 3D Reform Menu Setup Screen LAN Mode Password Security Sleep Timer Capture PC Card Files ChalkBoard Contents Information Menu Logo Security Enable, Disable, Keyword, Use Protect key, Drive, Read, Register, Delete Screen Type[...]

E-79 Menu windo ws or dialog bo x es typically hav e the f ollowing elements: Title bar ........... Indicates the menu title . Highlight .......... Indicates the selected menu or item. Solid tr iangle ... Indicates fur ther choices are av ailable. A highlighted triangle indicates the item is active . Ta b .................. Indicates a group of fea[...]

E-80 Check box ....... Place a checkmark in the square bo x to turn the option On. Slide bar .......... Indicates settings or the direction of adjustment. OK button ........ Press to confirm your setting. Y ou will retur n to the pre- vious menu. Cancel button .. Press to cancel y our setting. Y ou will retur n to the pre- vious menu. Close button [...]

E-81 USING ON-SCREEN MENU Menu Descriptions & Functions Source Select Selecting a Source Enables y ou to select a video source such as a VCR, D VD pla yer , laser disc pla yer , computer or document camera depending on what is con- nected to your inputs . Press the SELECT  b utton on the projector cabinet or on your remote control to high[...]

E-82 NO TE: Even if you switch the curr ent V iewer sour ce to another sour ce, the cur - r ent slide is retained. When you r eturn back to the V iewer , you will get the slide that has been r etained. A launcher will appear when you pr ess the MENU button. A press of the MENU button displa ys the toolbar; a press of the MENU b utton again displa y[...]

E-83 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions LAN Selects a signal from a LAN card plugged into the projector's card slot. Entry List Displa ys the list of the entr y signals. Use the SELECT  buttons on y our remote control or the projector cabinet to select the signal and press the ENTER b utton on the remote control o[...]

E-84 able f or RGB signal; Video and S-Video are av ailable f or composite signal. Source List: Set signal selection method. Lock: Set so that the selected signal cannot be deleted when "All De- lete" is e xecuted. Skip: Set so that the selected signal will be skipped during auto search. When complete, select OK and press ENTER. T o e xit[...]

E-85 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Picture (not available for V iewer and LAN) Adjusting Brightness, Contrast, Color , Hue, and Shar pness Brightness ....... Adjusts the brightness lev el or the back raster inten- sity . Contrast .......... Adjusts the intensity of the image according to the in- coming signal. Color ...[...]

E-86 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Image Options Selecting Aspect Ratio (not available for Viewer and LAN) Aspect Ratio allows y ou to select the best Aspect mode to display y our source image. When screen size 4:3 is selected f or the source, the f ollowing selec- tions will displa y: 4:3 ................... Standard 4[...]

E-87 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Input Signal Screen T ype 4:3 Screen 16:9 Screen 4:3 4:3 4:3 Window 4:3 Fill Letter Box Letter Box Letter Box Squeeze Wide Screen Crop Wide Screen NO TE: During 3D Reform adjustment, "Aspect Ratio" may not be available. Should this happen, fir st reset the 3D Reform data and [...]

E-88 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Clock ............... Use this item to fine tune the computer image or to remov e any vertical banding that might appear . This function adjusts the clock frequencies that eliminate the horizontal banding in the image . Press the SELECT  and  b uttons until the banding disappears[...]

E-89 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions NO TE: * When "Resolution" is set to "Native", "Overscan", "3D Reform", "Aspect Ratio" and "Scr een" are not available . * While you ar e displaying an image with higher r esolution than the pr ojector’ s native resolution, [...]

E-90 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Picture Management This option allows y ou to adjust neutral tint f or yello w , cyan or magenta. There are 5 f actor y presets optimiz ed f or various types of images, or y ou can set 4 user adjustab le settings. Presentation .... Recommended for making a presentation using a Po w erP[...]

E-91 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Selecting Color Correction Adjusts red, green, b lue, yellow , magenta, cyan and color gain each independently to correct the tint on whole screen. Selecting White Peaking Adjust the brightness of the white areas by using the slide bar . As the picture becomes dim, it looks more natura[...]

E-92 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Selecting Base Setting This feature allo ws you to use color correction or gamma v alues as ref erence data to optimize f or v arious types of images. Y ou can select one of the follo wing five settings . • Presentation • Video • Mo vie • Graphic • sRGB Pr ojector Options Usi[...]

E-93 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Menu Allows y ou to set preferences f or the on-screen menu. Press "OK" to sav e your changes f or all the features of P age 1 and Page 2. [P age1] Selecting Menu Language [Language]: Y ou can choose one of se ven languages f or on-screen instr uctions. The options are: Engli[...]

E-94 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Selecting a Mouse P ointer Icon [Mouse P ointer]: This option enables y ou to select one of nine different mouse point- ers when using a USB mouse. Selecting Menu Displa y Time : This option allows y ou to select how long the projector waits after the last touch of a button to turn off[...]

E-95 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Setup Enables y ou to set operating options. Press "OK" to sav e your changes f or all the f eatures of P age 1, Page 2, P age 3, P age 4 and Page 5. [P age 1] Setting Lamp Mode to Nor mal or Eco [Lamp Mode]: This f eature enab les you to select two brightness mode of the lam[...]

E-96 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Setting RGB 1 or 2 f or RGB OUT [RGBOUT T er minal] This option allows y ou to deter mine which RGB source is output from the RGBOUT connector during Idle mode. Last ............ The signal from the last RGB input will be output to the RGBOUT connector . RGB 1 ........ The signal from [...]

E-97 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions A uto Play Interval: Y ou can specify inter val time betw een 5 and 300 seconds . NO TE: The A uto Play Interval time set on “Slide Show Settings” of the Dynamic Image Utility 2.0 overrides the one set her e. Manual Pla y: Views a slide man ually when the Vie wer source is selected[...]

E-98 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions [P age 3] Selecting Signal F or mat [Signal Select] RGB1/2: Allows y ou to choose "RGB" f or an RGB source such as a com- puter , or "Component" f or a component video source such as a D VD pla yer . Nor mally select "RGB/Component" and the projector auto-[...]

E-99 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Enabling A uto Star t [Auto Start]: Tu r ns the projector on automatically when the po wer cable is in- ser ted into an activ e power outlet and the main po wer switch is tur ned on. This eliminates the need to always use the "P ower" b ut- ton on the remote control or projec[...]

E-100 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Enabling Idle Mode [Idle Mode]: The projector has two standb y modes: Standby and Idle . Standby is the mode that allo ws you to put the projector in the standb y condition which consumes less power than the idle mode . The pro- jector is preset for Standb y at the f actor y . When th[...]

E-101 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Last ............ Sets the projector to def ault to the previous or last ac- tiv e input each time the projector is turned on. A uto ............ Searches f or an active source in order of RGB1 → RGB2 → Video → S-Video → Viewer → RGB1 and displa ys the first found source. Se[...]

E-102 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Setting LAN Mode This f eature allows you to set v ar ious setting items when the projector is used on your netw or k. Consult with your netw ork administrator about these settings. NO TE: A LAN car d is requir ed for LAN connection; NEC's optional wireless LAN car d is available[...]

E-103 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions A utomatic ........ A utomatically assigns an IP address to the projector from a DHCP server . Manual ............ Pro vides a space f or you to register the IP address or subnet mask number obtained from y our network ad- ministrator . IP Address ...... Set y our IP address. Press to[...]

E-104 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Network T ype (required for wir eless only) Mode: Select communication method when using wireless LAN. Infrastructure ... Select this option when communicating with one or more equipment connected to the wireless or wired LAN network via an access point. 802.11 Ad Hoc Select this opti[...]

E-105 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions SSID (Network name): Enter an identifier (SSID) f or wireless LAN when selecting [Infrastruc- ture] or [802.11 Ad Hoc] in [Mode]. Communication can be done only with equipment whose SSID matches SSID f or your wireless LAN. Up to 32 alphanumeric characters can be used. NO TE: T o disa[...]

E-106 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions WEP (for Wir eless only) Select this option whether using the WEP (Wired Equivalent Priv acy) ke y f or encr yption or not. T o use encr yption, specify WEP key . Disable ............ Will not tur n on the encr yption feature . Y our communi- cations ma y be monitored by someone. 64bi[...]

E-107 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Ke y1-4: Enter encr yption ke y when selecting [64bit] or [128bit] in [WEP]. Up to 5 characters can be set in 64 bit and up to 13 characters in 128 bit. Press the “HEX” button to change to “ASCII” to set the ke y in ASCII digit. Y ou can toggle this button between “ASCII” [...]

E-108 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Sample of a message sent from the projector : The lamp is at the end of its usable life. Please replace the lamp. Projector Name: X X X X Lamp Hour Meter: xxxx [H] Projector Usage: xxxxxx [H] Sender's Address: Specify the senders address. Use the Software k eyboard. Up to 60 alph[...]

E-109 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Status Displa ys the status of the LAN settings. IP Address ...... Indicates the IP address of the projector . Subnet Mask ... Indicates the subnet mask of the projector . Gatew ay .......... Indicates the gate way of the netw or k connected to the projector . MAC Address .. Indicates[...]

E-110 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions DHCP Depending on your netw ork environment, acquiring an IP address from a DHCP ser ver ma y not be possible . Should this happen, consult your netw or k administrator to make changes to the f ollowing settings. Host Name option Select whether or not to add option hostname f or DHCP [...]

E-111 Client-identifier option Select whether or not to add option client identifier f or DHCP . None ......................... Not add Request ..................... Add at the time of DHCP_REQUEST . Discov er/Request ...... Add at the time of DHCP_DISCO VER and DHCP_REQUEST . Use MA C address Tu rn on to use MAC address f or Client-identifier . Cl[...]

E-112 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Setting a Password A passw ord can be set for y our projector to av oid operation by an unau- thorized person. There are two pass word options: one f or menu and the other f or logo . When a pass word is set, doing any one of the f ollowing four oper ations will displa y the Pass word[...]

E-113 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Delete To delete your pass word: 1. Highlight [Delete] and press the ENTER button. The "Current Pass word" screen will be display ed. 2. Use the Software ke yboard to type your password. Highlight "OK" on the “Current P assword” screen and then press the ENTER [...]

E-114 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions Security The Security function enables y ou to protect y our projector so that the projector will not project a signal unless you enter a k eyw ord. There is also an option to lock the projector b y using a registered PC card as a protect ke y. Once you ha v e registered your PC card [...]

E-115 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions To set up a ke yword to enable the Security function without using a regis- tered PC card 1. Use the SELECT  b utton to select “K eyword” and use the software k eyboard to enter a keyw ord. NO TE: Please make a note of your ke yword. 2. Use the SELECT  b utton to selec[...]

E-116 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions To turn on the projector when Security is enabled (when using your k ey- w ord only) 1. Press and hold the PO WER button for a minimum of tw o seconds. The projector will be tur ned on and display a message to the effect that the projector is security-pr otected. 2. Select [Projector [...]

E-117 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions To delete PC card data you registered 1. Use the SELECT  b utton to select "Delete" and use the SELECT  b utton to select the list windo w . 2. Use the SELECT  b utton to select the PC card data y ou wish to de- lete. 3. Press the SELECT  b utton to select [...]

E-118 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions T ools Provides tools f or setting sleep timer , captur ing images , displaying files or changing your bac kground logo in a PC Card and dra wing. NO TE: The "Captur e" and "PC Car d F iles" featur es ar e r equir ed for a PC card. Using Sleep Timer 1. Select your [...]

E-119 USING ON-SCREEN MENU ⬎ Menu Descriptions & Functions [P age 1] Source Name Input T erminal Entr y No . Horizontal F requency Ve r tical Frequency Sync P olarity [P age 2] Signal T ype Video T ype Sync T ype Interlace [P age 3] Remaining Lamp Time (%) Lamp Hour Meter (H) Projector Usage (H) Changing Backg round Logo: Y ou can change the [...]

E-120 NO TE: The pr ogr ess indicator shows the per centage of r emaining bulb life. The value informs you of the amount of lamp and pr ojector usage r espectively . Remaining Lamp Time Displa y: When the remaining lamp time reaches 0, the Remaining Lamp Time bar indicator changes from 0% to 100 Hours and star ts counting down. If the remaining lam[...]

E-121 MAINTENANCE This section describes the simple maintenance procedures you should f ollow to replace the lamp , and to clean the cabinet and the lens. Replacing the Lamp After your lamp has been oper ating f or 2000 hours (up to 3000 hours : Eco mode) or longer , the "Lamp" indicator in the cabinet will blink red and the message will [...]

E-122 MAINTENANCE Interlock To replace the lamp: 1. Loosen the lamp cover scr ew until the scr ewdriver goes into a fr eewheel- ing condition and remo ve the lamp cov er . The lamp cover screw is not r emov able. 2. Loosen the two screws securing the lamp housing until the scr ewdriver goes into a freewheeling condition. The two scr ews ar e not re[...]

E-123 MAINTENANCE 4. Insert a new lamp housing until the lamp housing is plugged into the socket. CAUTION Do not use a lamp other than the NEC replacement lamp (L T60LPK). 5. Secure it in place with the two scr ews. Be sure to tighten the screws. 6. Reattach the lamp cover . 7. Tighten the lamp cov er screw . Be sure to tighten the scre w .[...]

E-124 S E L E C T C N A C E L T E R N E E M N U S O U R C E A U T O A D J U S T O N S T A N D B Y S T A T U S P O W E R L A M P A L I G N M E N T PC-CARD 8. After you install a new lamp, fr om the menu select [Projector Options] → [Setup] → [Page 4] → [Clear Lamp Hour Meter] to reset the lamp usage hours. If the projector will not be tur ned [...]

E-125 Lens Protector The lens barrel has threads on the outside f or mounting a commercially a v aila b le lens protector ( φ 62mm f or 8761 and φ 72mm f or 8760 ) to protect the lens from dir t, dust, scratches and damage. Note that both a lens protector and the supplied lens cap cannot be used at the same time . CA UTION: Use only tr ansparent [...]

E-126 TROUBLESHOOTING This section helps y ou resolv e problems y ou may encounter while setting up or using the projector . Power Indicator Indicator Condition Projector Condition Note Off Blinking light Steady light Green blinking Green blinking Orange blinking 0.5 sec ON, 0.5 sec OFF 2.5 sec ON, 0.5 sec OFF 0.5 sec ON, 0.5 sec OFF The main power[...]

E-127 TROUBLESHOOTING Indicator Condition Projector Condition Note Off Blinking light Steady light Normal Lamp has reached its end of life. Lamp replacement mes- sage will be displayed. Lamp has been used beyond its limit. The projector will not turn on until the lamp is re- placed. Lamp mode is set to Eco mode Red Red Green – Replace the lamp. R[...]

E-128 Does not turn on No picture Image isn’t square to the screen Picture is blurred Image is scrolling verti- cally , horizontally or both Remote control does not work Indicator is lit or blink- ing Cross color in RGB mode USB mouse does not work • Check that the power cable is plugged in and that the power button on the projector cabinet or [...]

E-129 When using the Viewer function TROUBLESHOOTING • Is “Viewer” selected from the Sour ce menu? • Is the PC card seated in the PC Card slot completely? • Are slide data stored in the PC card? • Have the contents of the PC card been destroyed? • Use a computer , etc., to repair the data. Problem Check These Items F or more informati[...]

E-130 SPECIFICA TIONS This section provides technical inf or mation about the L T260K/L T240K Projector's perf or mance Model Number L T260K/L T240K Optical DMD™ Single Chip Digital Micromirror De vice(DMD™) Resolution 1024 ⳯ 768 pix els* up to UXGA with Advanced AccuBlend Lens Manual zoom and f ocus: 8761 : F2.2 - 2.5 f=28.4mm - 34.0mm [...]

E-131 External Control RS232, IR, LAN (optional) Sync Compatibility Separ ate Sync / Composite Sync / Sync on G Built-in Speakers 2W ⳯ 1 (monaural) Po wer Requirement 100 - 120V A C / 200 - 240V AC , 50 / 60 Hz Input Current 3.0A (100 - 120V A C) / 1.5A (200 - 240V AC) Po wer Consumption 280W (0.6W at Standby) Mechanical Installation Orientation:[...]

E-132 APPENDIX Cabinet Dimensions Unit = mm (inch) 260 (10.24") 57 (2.24") 275 (10.83") 300 (11.8") * 120 (4.7") 107 (4.2") 83 (3.27") 92 (3.6") * L T240K: 319mm (12.56”)[...]

E-133 Mini D-Sub 15 Pin Connector Pin Assignments of D-Sub RGB Input Connector Pin No. RGB Signal (Analog) YCbCr Signal 1R e d C r 2 Green or Sync on Green Y 3 Blue Cb 4 Ground 5 Ground 6 Red Ground Cr Ground 7 Green Ground Y Ground 8 Blue Ground Cb Ground 9 No Connection 10 Sync Signal Ground 11 Ground 12 Bi-directional D A T A (SD A)* 13 Hor izon[...]

E-134 Compatible Input Signal List Signal Resolution F requency H. Refresh Rate Dot Clock ( Dots ) ( kHz ) ( Hz ) ( MHz ) NTSC – 15.734 60 – PA L– 15.625 50 – SECAM – 15.625 50 – VESA 640 ⳯ 480 31.47 59.94 25.175 IBM 640 ⳯ 480 31.47 60 25.175 MAC 640 ⳯ 480 31.47 60 25.175 MAC 640 ⳯ 480 34.97 66.67 31.334 MAC 640 ⳯ 480 35 66.67[...]

E-135 #M AC 1280 ⳯ 1024 69.89 65.2 118.5 #H P 1280 ⳯ 1024 78.125 72.01 135 # SUN 1280 ⳯ 1024 81.13 76.11 135 # VESA 1280 ⳯ 1024 79.976 75.03 135 # VESA 1280 ⳯ 1024 91.146 85.02 157.5 # HDTV (1080i)(1125i) 1920 ⳯ 1080 33.75 60 Interlace 74.25 # HDTV (1080i)(1125i) 1920 ⳯ 1080 28.13 50 Interlace 74.25 # HDTV (720p)(750p) 1280 ⳯ 720 45[...]

E-136 APPENDIX Cable Connection Communication Protocol Baud rate : 38400 bps Data length : 8 bits Pa r ity : No parity Stop bit : One bit X on/off : None Communications procedure : Full duplex NO TE: Depending on the equipment, a lower baud rate may be r ecommended for long cable runs. PC Control Codes and Cable Connection PC Control Codes Function[...]

E-137 APPENDIX Using Softwar e Keyboard 1 to 0 and Characters ......... Use to type in IP address or projector name SP ....................................... Inser ts a space BS ....................................... Deletes one character bac kward  ......................................... Retur ns to the pre vious  .......................[...]

E-138 APPENDIX Operation Using an HTTP Br owser Overview The use of HTTP ser ver functions will allo w control of the projector from a w eb browser without the installation of special softw are. Please be sure to use “Microsoft Inter net Explorer 4.x” or a higher v ersion f or the web browser . (This de vice uses “J avaScript” and “Cookie[...]

E-139 APPENDIX Preparation Befor e Use Make netw ork connections and set up the projector and confir m that it is complete before engaging in bro wser operations. (See “Setting LAN Mode” on page E-102.) Operation with a browser that uses a pro xy ser v er may not be possible depending on the type of pro xy ser ver and the setting method. Althou[...]

E-140 APPENDIX Structure of the HTTP Server Po we r: This controls the po wer of the projector . On ................... P ower is switched on. Off ................... P ower is switched off . V olume: This controls the volume of the projector .  ..................... Increments the v olume adjustment value .  ..................... Decrements [...]

E-141 Picture: Controls the video adjustment of the projector . Brightness  ... Increments the brightness adjustment value . Brightness  ... Decrements the brightness adjustment value . Contrast  ...... Increments the contrast adjustment value . Contrast  ...... Decrements the contrast adjustment value . Color  ........... Increments[...]

[...]

DUKANE CORPORATION TWO-YEAR LIMITED WARRANTY This Dukane projector is warranted to the original purchaser for a period of two (2) years from the original purchase date – in normal operating conditions – against defects in material and workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A [...]

Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.com Phone: (630) 762-4040 Orders: (800) 676-2485 Information: (800) 676-2486 Fax: (630) 584-5156 Parts & Service: (800) 676-2487 Fax: (630) 584-0984 Audio Visual Products 401-8760-8761-00[...]