EverFocus EDSR 400F manuel d'utilisation

Volume 1 Instr uction Man ual E E D D S S R R 4 4 0 0 0 0 F F / / 6 6 0 0 0 0 F F / / E E D D S S R R 9 9 0 0 0 0 F F / / 1 1 6 6 0 0 0 0 F F[...]

EVERFOCUS ELECTRONICS CORPORATION EDSR 400F / EDSR600F EDSR 900F / EDSR1600F Instr uction Guide © 2004 Everfocus Electronics Corp 2445 Huntingto n Drive Phone 626.844 .8888 • Fax 626.8 44.8838 All ri ghts re served. N o part o f the cont ents of th is manual may be reproduced or transmitted in any form or by any means without written permissi on[...]

T able of Contents Introduction I CHAPTER 1 Product Overvi ew 1 Features 1 Specifications 2 Front Panel Keys 3 Back Panel Connecti ons 5 CHAPTER 2 Installa tion 7 Basic Wiring Instruc tions 8 Hard Disk Drive In stallation 9 Final Install Pr ocess 9 CHAPTER 3 DVR Menu Setup 10 Clock/Languag e Set ting Menu 11 Daylight Savin gs Menu 13 Timer Setting [...]

Introduction t o TCP/IP 60 Subnet Masks 61 Gateway Address 61 Virtual Ports 61 Pre-Installati on 62 What type of Network Co nne ction 63 Simple One to One Conne ction 64 Direct High Speed Modem Co nnection 70 Router or LAN Connec tion 72 CHAPTER 10 Linksys Port Forwa rding 75 Dynamic DNS 78 CHAPTER 11 D-Link Port Forw arding 80 Dynamic DNS 83 CHAPT[...]

[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 1 Pr oduct Ov er view DVRs are the industry’s first full-featured digital video reco rder designed specifically for use within the security industry. The Digital Video Recorder incorporates all the benefits of digital video recording, is simple to install, and ope rates just like a VCR. Highly efficient c[...]

EVERFOCUS ELECTRONICS CORPORATION Specifica tions 2[...]

EVERFOCUS ELECTRONICS CORPORATION F ront Panel K eypads Keys: 3[...]

EVERFOCUS ELECTRONICS CORPORATION 4[...]

EVERFOCUS ELECTRONICS CORPORATION Bac k P anel Connections 5[...]

EVERFOCUS ELECTRONICS CORPORATION 6[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 2 Installa tion The installations described below should be made by qualified service personnel or system installers. Please refer to the following diag ram for the basic wiring connections. ¾ Please Note: Monitors and Camera s must be purchased separately. EDSR400: Camera 1 ~4 / EDSR600: Ca mera 1~6 EDSR9[...]

EVERFOCUS ELECTRONICS CORPORATION Basic W iring Instr uctions Please refer to diagram 1 on page 9 to assist you with this portion of the installation. ¾ Power: Connect the power source or adapter into the power socket shown in diagram 1.  Please Note: Do not plug the digi tal video recorder into the same power source as the cameras. ¾ Cameras:[...]

EVERFOCUS ELECTRONICS CORPORATION Har d Disk Driv e Installation The first step in installing the hard drive is to insert the hard drive sleeve into the machine. The hard disk drive default setti ng is initially set to master. The second step is to insert the key prov ided and turn the tray key to the lock position. If this process is ignored the h[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 3 D VR Menu Setup Assuming you have completed the first two chapters of this manual. You are now ready to begin setting up the digital vi deo recorder menu. To begin this process, press the MENU key. Once inside the main menu you will find ther e are 17 setup option pages as follows. Diagram 2 Turning the j[...]

EVERFOCUS ELECTRONICS CORPORATION Cloc k Setting Menu Diagram 3 Diagram three is a screen shot of th e Clock/Language Setting Menu. In the Clock/Language Setting Menu the follo wing fields are defined as follows: ¾ Date: This field represents the curre nt date on the DVR. To change this, simply use the Jog Dial on the DVR. Press the Enter key to m[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Menu Language: This field is set to English from factory and can not be changed. ¾ Video System: This field is set to NTSC from factory which is the North American Video Standard and can not be changed. The European and Asian Video Standards are PAL. ¾ Version: This field represents the firmware version the di[...]

EVERFOCUS ELECTRONICS CORPORATION Daylight Sa vings Menu Diagram 4 In this menu you can set the DVR to adjust the daylight savings time automatically for you. ¾ Daylight saving: This field is to turn th e daylight savings function on or off. . To change this, simply use the Jog Di al on the DVR. Press the Enter key to make your selection. ¾ Start[...]

EVERFOCUS ELECTRONICS CORPORATION Timer Setting Menu Diagram 5 Diagram five is a screen shot of the Timer Setting Menu. In this menu you can set a unique timer any day of the week to start r ecording from a specified start time to an end time. In the Timer Setting Menu the following fields are defined as: ¾ Week: This field represents the day of t[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Speed: This field is used to set the sp eed at which you would like the timer record to be recording at. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection.  Please Note: See Appendix B to find the appropriate speed to fit your recording needs. Set: This field is us[...]

EVERFOCUS ELECTRONICS CORPORATION Sequence Setting Menu Diagram 6 Diagram Six is a screen shot of the Sequence Setting Menu. Th is menu is for setting up the way in which video is sequenced th rough the main monitor output. In the Sequence Setting Menu the followin g fields are define d as follows: ¾ Main Monito r: This field is to s et the sequen[...]

EVERFOCUS ELECTRONICS CORPORATION  Dwell Time: This field represents the rate at which the cameras will sequence on the main monitor. The dwell time for the auto sequence can be set from 0 to 99 seconds. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. 17[...]

EVERFOCUS ELECTRONICS CORPORATION Title Setting Menu Diagram 7 Diagram seven is a screen shot of the Titl e Setting Menu. In this menu you can set a unique title for each of your cameras. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Example: CH1 : FrontDoor CH2 : BackDoor CH3 : Hallway CH4 : Clo[...]

EVERFOCUS ELECTRONICS CORPORATION Co ver t Setting Menu Diagram 8 Diagram eight is a screen shot of the Covert Setting Menu. In this menu you can set which cameras to be covert or hidden on the main monitor.  Channel: This field represents the ch annel you are setting to sequence.  Operation: This field is to turn on or off the camera for the[...]

EVERFOCUS ELECTRONICS CORPORATION Alar m Setting Menu Diagram 9 Diagram nine is a screen shot of the Alar m Record Set ting Menu. This menu contains all the alarm operations and options need ed to successfully complete an alarm recording. In the Alarm Reco rd Setting Menu the follow ing fields are defined as: ¾ Operations: This field is to turn al[...]

EVERFOCUS ELECTRONICS CORPORATION  Please Note: Refer to Appendix C for more informat ion about setting up the alarm board. ¾ Duration: When any sensor alarm conn ected to the device is activated, the device will immediately react with an alarm and display the warning message. This entry is used to set the al arm duration from 1 to 99 seconds. [...]

EVERFOCUS ELECTRONICS CORPORATION Motion Setting Menu Diagram 10 Diagram ten is a screen shot of the Motion Setting Menu. Th is menu is for setting up the digital recorder for moti on recording. In the Motion Setting Menu the following fields are defined as follows: ¾ CH: This field represents the camera channels. ¾ OP: This field is to set the o[...]

EVERFOCUS ELECTRONICS CORPORATION message. This entry is used to set the al arm duration from 1 to 99 seconds. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Manual Edit: This field represents manual editing of each camera for motion. To change this, simply use the Jog Dial on the DVR. Press the E[...]

EVERFOCUS ELECTRONICS CORPORATION Diagram 12  To exit this screen after you have finished editing simply press the MENU button. 24[...]

EVERFOCUS ELECTRONICS CORPORATION R ecor d Setting Menu Diagram 13 Diagram thirteen is a screen shot of the R ecord Setting Menu. This menu contains the speed and quality for recordin g all the time. In the Record Setting Menu the following fields are defined as: ¾ Normal Reco rd: o Speed: Th is field represents the sp eed at which the recorder w [...]

EVERFOCUS ELECTRONICS CORPORATION  Lower : 15KB  Low : 19KB  Basic : 23KB  Standard : 27KB  High : 31KB  Superior : 35KB To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. o Disk Full: This field represents what to do when the Hard Disk Drive gets full. In this case the default is s et [...]

EVERFOCUS ELECTRONICS CORPORATION  High : 31KB  Superior : 35KB To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Pre -Alarm Record: o Operation: This field is to s et the option of turning pre-alarm recording on or off. If Operation is turned on the DVR will respond by recording 5 seconds befo[...]

EVERFOCUS ELECTRONICS CORPORATION Netw or k Setting Menu Diagram 14 Diagram fourteen is a screen shot of the Network Setting Menu. This menu is for setting up the configuration for network ing to the DVR. Please refer to the Networking Chapter of this ma nual to fully understand how to setup your network for this DVR. In the Network S etting Menu t[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Net mask: This field is to set the su bnet mask for your network so as the DVR will be recognized within the n etwork. Example: 255.255.255.000. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Gateway: This fie ld is to set the gateway for your network so the DV[...]

EVERFOCUS ELECTRONICS CORPORATION Contr ol Setting Menu Diagram 15 Diagram fifteen is a screen s hot of the Control Setting Menu . This menu is for setting up a connection from the digita l recorder to a computer to transfer instructions or information using the HyperTerminal prog ram in Windows. In the Control Setting Menu the following fields are[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ RS232 Parity: This field is to select the parity level at which you will be connected. You can choose between None , Odd, or Even parity levels. Default is set to none. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ RS232 Data Bit: Th is field is the data bit a[...]

EVERFOCUS ELECTRONICS CORPORATION Buzzer Setting Menu Diagram 16 Diagram sixteen is a screen s hot of the Buzzer Setting Menu . This menu is to set the internal buzzer. In the Buzzer Setting Menu the following fiel ds are defined as: ¾ Buzzer: This field is to turn the inter nal buzzer enable or disable the internal buzzer. The default is set to e[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Disk Full: This field is to turn th e buzzer on or off when the Hard Disk Drive is full. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Video Loss: This opt ion is to turn the buzzer on or off when the DVR experiences video loss. To change this, simply use the [...]

EVERFOCUS ELECTRONICS CORPORATION Ar chiv e Setting Menu Diagram 17 Diagram seventeen is a screen shot of the Archive Setting Menu. This menu is for setting up the way in which video is arch ived within the machine. In the Archive Setting Menu the following fi elds are defined as follows: ¾ Picture Size: This field is to set the picture size for c[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Time Stamp Posit ion: This field is to set the position of the time stamp. You can set the time position either on top or bottom. The default is set to top. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Water Mark: This option is to turn water mark on or off w[...]

EVERFOCUS ELECTRONICS CORPORATION Ma trix Setting Menu (onl y on EDSR-900 and EDSR- 1600) Diagram 18 Diagram 19 Diagram 20 Diagrams eighteen through nineteen are screen shots of the Matrix Setting Menu. This menu is for setting up the way in which vi deo is sequenced through the matrix monitor and call monitor outputs. In the Matrix Setting Menu th[...]

EVERFOCUS ELECTRONICS CORPORATION  Channel: Represents the channels yo u want to be displayed in full screen on this output. To change th is, simply use the Jog Dial on the DVR. Press the Enter key to make your selection.  Dwell Time: This field represents the rate at which the cameras will sequence on the call monitor. The dwell time for the[...]

EVERFOCUS ELECTRONICS CORPORATION Disk Setting Menu Diagram 21 Diagram 21 is a screen shot of the Disk Setting Menu. This menu is for viewing Disk information and formatting the disks. In the Disk Setting Me nu the following fields are defined as follows: ¾ Disk Usage : This field signifies the nu mber of Hard Drives the machine can store too. ¾ [...]

EVERFOCUS ELECTRONICS CORPORATION PTZ Setting Menu Diagram 22 Diagram 22 is a screen s hot of the PTZ setting menu . PTZ control functions are accessible through the web interface. You now have the same basic controls used with the EKB series keyboards over the web in terface. This allows you to control the camera pan, tilt and zoom functions while[...]

EVERFOCUS ELECTRONICS CORPORATION Connections: The Data Control cables connect to the back of the EDSR using the RS 485 Port. Depending on how your c onnections are set up and the num ber of cameras you are using, you will need to connect the data cables to Pins 3 and 6 on an y of the 2 RS-485 ports. Pin 3 being Positive (+) and pin 6 being negativ[...]

EVERFOCUS ELECTRONICS CORPORATION System Setting Menu Diagram 24 Diagram 24 is a screen shot of the System Setting Menu. This menu is for setting up any additional options and restoring defaults to the digital recorder. In the System Setting Menu the following fi elds are defined as follows: ¾ Play with Audio 1 and 2: These fields are to turn on a[...]

EVERFOCUS ELECTRONICS CORPORATION you into the menu options. The passwor d supports up to 6 characters. The available alphanumeric characters are:  0 to 9, A to Z, and /( ) . - * & @ : ” To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. ¾ Password Le vel 3: This field is the password for the s[...]

EVERFOCUS ELECTRONICS CORPORATION To Load the defaults simply use the ar row buttons to change this option to yes. This will bring up a second dialog which asks you if you want t o do a load defaults again. To change this , simply use the Jo g Dial on the DVR. Press the Enter key to make your selection.  Please Note: See Load Defaults Chapter fo[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 4 R e cor ding Ov er view Before continuing please be sure to have reviewed DVR Menu Setup (Chapter 3). You are now ready to begin setting up the machine for normal recording. This chapter will show you how to setup the reco rder for basic recording. Basic R ecor ding Setup ¾ Assuming you have completed th[...]

EVERFOCUS ELECTRONICS CORPORATION Diagram 25 ¾ To stop reco rding simply press the Stop button.  Please Note: When the Hard Drive is full, the DVR will either stop recording automatically or overwrite fr om the beginning of the hard drive. This is all dependent on what was set in the record setti ng (see page 25). Timer R ecor ding Setup ¾ Ass[...]

EVERFOCUS ELECTRONICS CORPORATION Diagram 26 ¾ To stop reco rding simply press the Stop button.  Please Note: When the Hard Drive is full, the DVR will either stop recording automatically or overwrite fr om the beginning of the hard drive. This is all dependent on what was set in the record setti ng (see page 25). Motion R ecor ding Setup ¾ As[...]

EVERFOCUS ELECTRONICS CORPORATION  Please Note: Our recorders are deve loped for segment recording. One segment or motion event can record to one sector on the hard drive. Hard drives contain on average 2 56 sectors. Therefore recording on motion only you will see the Record Light going on and off you are not recording properly in motion. Th is [...]

EVERFOCUS ELECTRONICS CORPORATION Alar m R ecor ding Setup ¾ Assuming you have completed the setup options in Chapter 1 and 2. Log into the DVR menu by pressing the Menu button. ¾ Once You Reach the Record Setting Menu (See Page 25) change the Recording speed and quality that best fits your application. Turning the jog dial clockwise or counter c[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 5 Playbac k Ov er view Before continuing please be sure to have reviewed DVR Menu Setup (Chapter 3). You are now ready to begin setting up the machine for playback. This chapter will show you how to setup the recorder for basic playback. Basic Playbac k ¾ Assuming you have completed the setup opt ions in C[...]

EVERFOCUS ELECTRONICS CORPORATION Diagram 29 ¾ Use the Jog Dial to select segmen t list and press the enter key. ¾ Diagram 30 illustrates what the segment list may look like. Use the Jog Dial to choose a segment you want to playback and press the enter key. This in turn will start playing the segment you chose. Diagram 30 ¾ To stop playing back [...]

EVERFOCUS ELECTRONICS CORPORATION 2. Alarm List Playback ¾ Assuming you have completed the setup options in Chapter 1 through 4. ¾ Press the search button to enter th e search menu. (See Diagram 31) Diagram 31 ¾ Use the Jog Dial to select alarm list and press the enter key.  Please Note: If the alarm list is empty you will not be able to ente[...]

EVERFOCUS ELECTRONICS CORPORATION 3. Date/Time Playback ¾ Assuming you have completed the setup options in Chapter 1 through 4. ¾ Press the search button to enter th e search menu. (See Diagram 33) Diagram 33 ¾ Use the Jog Dial to select Date/Ti me and press the enter key. ¾ Diagram 34 illustrates what the Date/Ti me field may look like. Use th[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 6 Cop ying V ideo (Compact Flash Car d Archiving) Before continuing please be sure to ha ve reviewed the preceding chapters. You are now ready to copy an image or video from the DVR. This chapter will show you how to copy a still image or movie from the recorder. ¾ Please Note: Lexar Compact Flash Cards ar[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Once you have stopped any type of recording on the DVR you are ready to do archive. ¾ The Second Step is to play the video you want to archive. Please refer to chapter 5 to for playing back video. ¾ Once you are in playback mode press t he pause button. You may use the jog dial to go back or forward to se lect[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ The Second Step is to play the video you want to archive. Please refer to chapter 5 to for playing back video. ¾ Once you are in playback mode, select th e camera and have the portion of the video you wish to copy. Then press the copy button. Diagram 37 T ech Tip : When copying a movie file to a flash card, by [...]

EVERFOCUS ELECTRONICS CORPORATION V iewing a Copied File ¾ First step is to play the video or image you have stored on the Compact Flash card is to take the Compact Flash card and insert it into the Compact Flash Reader which came with your digital reco rder. Insert the other end of the Flash card reader into the USB port of your computer. ¾ Open[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 7 Audio Ov er view This chapter will try to give you deta ils on how to setup audio on the DVR. Before we begin the process of connecting audio to your digital recorder we should have the following items. A Line level microphone (RCA input) and speakers for playback output (RCA). You will not be able to hea[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 8 Ho w to Upg r ade Fir mwar e on the D VR? This chapter will try to give you a detailed instruction on how to upgrade the DVR. This will be a helpful in completing the upgrading process. ¾ Please go to ftp://208.50.31.200 and go to DVR Firmware upgrade folder. Then click on the fold er that represents you[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Using the enter button to navigate in the menu. Highlight System Upgrade turn NO to YES (use jog wheel to select). ¾ Highlight YES again and press enter (use jog wheel to select). ¾ Next to System Upgrade you will notice it say "Reading....then Programming...then Success..." ¾ Once you have read suc[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 9 Netw or king Ov er view This chapter will try to give you a detailed instruction on how to network the DVR. Before we begin the process of networking your digital recorder we should have a working knowledge of what a network is and how it works. This will be a helpful in completing the networking process.[...]

EVERFOCUS ELECTRONICS CORPORATION Ga teway Addr ess Each host in a LAN has a gateway. A gateway address is composed of four octets (numbers in the range of 0 to 255) separated by decimal points. The gateway address is used to uniquely identify a host or computer on the LAN which assigns the IP addresses to your n etwork. For example, a Linksys rout[...]

EVERFOCUS ELECTRONICS CORPORATION Pr e-Installa tion Before we begin with the installation we must ask ourselves a few questions in order to figure out where to begin with networking our DVR’s. Do you have Hi-speed Internet? ______________ There are many types of high speed Internet available. Three commonly used ones are T1, Cable, and DSL (in o[...]

EVERFOCUS ELECTRONICS CORPORATION DDNS. DDNS is a Dynamic Domain Name Server, a service that provides a central (public) database where DNS information can be stored and retrieved. It allows those using a dynamic IP address to be registered centrally so users can connect to it by name. W ha t T ype of Networ k Connection do you ha v e? Everfocus DV[...]

EVERFOCUS ELECTRONICS CORPORATION Simple One to One Connection Cat 5 Cross-over-cable Crossover Ethernet Cable Pin outs: The Diagram below shows the pin conf igurations for a cross over cable. Diagram 31 Connection Procedure: ¾ The First step is to purchase or ma ke a cross over cable. We recommend purchasing one if you have never made a cross ove[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Assign an IP address of 192.168.001.003 to the DVR, a Subnet mask of 255.255.255.000, and a default gateway of 192.168.001.001. ¾ The next step is to get the computer onto the same network to do this you will need administrator access to your windows machine. ¾ To assign a static IP address in windows 2000/XP.[...]

EVERFOCUS ELECTRONICS CORPORATION 66[...]

EVERFOCUS ELECTRONICS CORPORATION 67[...]

EVERFOCUS ELECTRONICS CORPORATION 68[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Once you have reached this point click ok and restart both the computer and the digital recorder. ¾ To access the DVR from the computer simply open Internet Explorer and in the address bar type: http://192.168.1.3 69[...]

EVERFOCUS ELECTRONICS CORPORATION Dir ect High Speed Modem Connection Internet DVR Hi-speed modem Cat 5 Straight Th rough Cable Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Diagram 32 Connection Procedure: ¾ The First step is to purchase or make a straight through cable. We recommen[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Now Log into the Everfocus DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. (See page 28 for more instructions) ¾ Assign the Static IP address which you obtained from the internet service provider to the DVR, the Subnet mask from the internet service provider to the DVR,[...]

EVERFOCUS ELECTRONICS CORPORATION R outer or LAN Connection Internet Hi-speed modem DVR Cat 5 Straight Th rough Cable Router Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Diagram 33 Connection Procedure: ¾ The First step is to purchase or make a straight through cable. We recommend p[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Once you have a straight through cable plug one end into the LAN port on the back of the recorder and the other into the router. ¾ Now Log into the Everfocus DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. (See page 28 for more instructions) ¾ If you have a Linksys Rou[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Please Note: Make sure the modem is in bridge mode. If your Internet Service Provider is BellSouth you will have a modem/router. BellSouth provides a Westell modem that includes a built-in router. You will need to disable the router functionality. ¾ The next step is to open ports within your router. Open virtua[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 10 Linksys P or t F orw ar ding This chapter will cover a few simple configurations for the Linksys router. Please understand we do not support this product and will not give tech support on it. If you need Technical support on this router you must call Linksys. This Chapter is to offer some help to the ins[...]

EVERFOCUS ELECTRONICS CORPORATION The first screen that appears displays the Setup tab. This allows you to change the Router's general settings. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. The Applications and Gaming Tab allows you to set up public s[...]

EVERFOCUS ELECTRONICS CORPORATION Application - In this field, enter the name you wish to give the application. Each name can be up to 12 characters. Start/End - This is the port range. Enter the number that starts the port range under Start and the number that ends the range under End . Protocol - Enter the protocol used for this application, eith[...]

EVERFOCUS ELECTRONICS CORPORATION DVR 3333 to 3333 Both 192.168.1.50 Enable DVR 4444 to 4444 Both 192.168.1.50 Enable DVR 6666 to 6666 Both 192.168.1.50 Enable ¾ If your Internet Service Provider Bloc ks port 80. Simply do the following:  Go to Networking setting menu and change the HTTP port 0080 to 8100 and press menu twice to exit from menu [...]

EVERFOCUS ELECTRONICS CORPORATION DDNS Service - From this pull-down me nu, enter the DDNS service with which you have membership. User Name - Enter the User Name for your DDNS account. Password - Enter the Password for your DDNS account. Host Name - The is the DDNS URL assi gned by the DDNS service. Internet IP Address - This is the Router ’s cu[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 11 D-Link P or t F orwar ding This chapter will cover a few simple configurations for the D-Link router. Please understand we do not support this product and will not give tech support on it. If you need Technical support on this router you must call D-Link. This Chapter is to offer some help to the install[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ The next step is to open ports within your router. Go to Virtual Server in the router. Example1: Protocol Type - The protocol used for the virtual service. Public Port - The port number on the WAN (Wid e Area Network) side that will be used to access the virtual service. Private Port - The port number of the ser[...]

EVERFOCUS ELECTRONICS CORPORATION Name - Enter the name referencing the virtual se rvice Private IP - The server computer in the LAN (Local Area Network) that will be providing the virtual services. If you have a Web server that you wanted Internet users to access at all times, you would n eed to enable it. Web (HTTP) server is on LAN (Local Area N[...]

EVERFOCUS ELECTRONICS CORPORATION Dynamic DNS Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. This is a useful feature since many computers do not use a static IP address. ¾ To setup Dynamic DNS simple go to Tools and the Misc. At the bottom of the screen you will be able to enable DynDNS. ¾ Once y[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 12 DDNS This chapter will cover a few simple configurations for setting up DDNS. Please understand we do not support this product and will not give tech support on it. If you need Technical support on DDNS you must call Linksys or D-Link. This Chapter is to offer some help to the installer and end user noth[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ This is where you file out the information DynDNS requires. You will then receive an email to confirm yo ur account once you confirm you will login into DynDNS.org. ¾ After you have logged in click on click on the account tab and the click on Add Host link right next to Dynamic DNS. ¾ The next step is to add a[...]

EVERFOCUS ELECTRONICS CORPORATION ¾ To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// The DDNS you created example everfocu.homeip.net 86[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 13 V iewing thr ough Inter net Explor er ¾ To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// (LAN or IP address of your internet service provider) ¾ The digital video login page will appear on the screen similar to the one shown above. ¾ User must enter [...]

EVERFOCUS ELECTRONICS CORPORATION ¾ Then click on the submit button and you will be logged into your recorder. Main Screen 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 88[...]

EVERFOCUS ELECTRONICS CORPORATION 19. Refresh to get recorded data. 20. PTZ control. ¾ Please Note: If any icon is grayed, it means that particular function is not accessible. Playback by Segment list 89[...]

EVERFOCUS ELECTRONICS CORPORATION Playback by Alarm list Playback by Date and Time PTZ Control 90[...]

EVERFOCUS ELECTRONICS CORPORATION Chapter 14 Interf ace Specifica tions This Digital Video Record er may be contr olled by a com puter or a terminal via the standard D- SUB 9-pin RS-232 connector.  D-SUB 9-pin connec tor specifications:  The pin assignment of the 9-pin D-SUB connector 91[...]

EVERFOCUS ELECTRONICS CORPORATION T r ansmission Setting There are 6 different speeds that can be used to transmit instruction or information through the RS232/RS485 port on the device, 1200 baud, 2400 baud, 4800 baud, 9600 baud, 19200 baud, and 3840 baud. The default setting from the factory is 9600 baud. Please refer to RS232/RS485 Setting Menu o[...]

93[...]

Remote keys (Opcode= 0x4B) Data1 KEY 0x00 CH1 0x01 CH2 0x02 CH3 0x03 CH4 0x04 MODE 0x05 ZOOM 0x06 SEQ 0x07 MENU 0x08 REC 0x09 REV. PLAY 0x0A STOP 0x0B PLAY 0x0C PAUSE 0x0D SEARCH 0x0E COPY 0x0F DISPLAY 0x10 SHUTTLE <<x1 0x11 SHUTTLE <<x2 0x12 SHUTTLE <<x4 0x13 SHUTTLE <<x8 0x14 SHUTTLE <<x16 0x15 SHUTTLE <<x32 0x[...]

Matrix command (Opcode= 0x4D) D ata1 Matrix Function 0x00 M atrix Mon0 – CH01 spot 0x01 M atrix Mon0 – CH02 spot 0x02 M atrix Mon0 – CH03 spot 0x03 M atrix Mon0 – CH04 spot 0x04 M atrix Mon0 – CH05 spot 0x05 M atrix Mon0 – CH06 spot 0x06 M atrix Mon0 – CH07 spot 0x07 M atrix Mon0 – CH08 spot 0x08 M atrix Mon0 – CH09 spot 0x09 M at[...]

Appendix A Re m o t e C o n t r o l 96[...]

Appendix B Time La pse Mode R ecor ding Time 97[...]

98[...]

Appendix C Alar m Boar d Configur a tion 99[...]

Appendix D RJ45 (RS485) Pin Assignment 100[...]

T roubleshooting If you have difficulty operating your syst em, run through the following checklist to see if you can solve the problem.  The DVR will not go into record mode?  Make sure the HDD is locked in with the k eys. Also check t o make sure the hard drives are set to Master. A diagra m located on the H ard Drive Label will show you ho[...]

3. If you are using a ro uter are the ports in your router opened? ( NOTE: Please be sure that ports 80 , 1111, 2222, 3333, 4444, 6666 are open .) 4. If you are using Windows X P please update t he Java Virtual Machine. This can be done by going to http://java.sun.com /downloads/index.html and downloading the file called JavaVM.  If you have a D[...]

Most F r equentl y ask Questions: Q. How can I go to full screen mode o ver the network? A. You can s witch to full screen mode, b y clicking on full screen on the right bottom off of your screen. Q. On full scree n mood how can I change to a different camera ov er the network? A. Once you ar e on the full screen mode, you can do a right click on t[...]

Q. How can I erase everything fro m My Hard Dri ve? A. You can do a disk renew under Disk menu for EDSR 1600/900/600/400F Q. I am recording on motio n only, but only ge tting a few hours of recording time on my Hard Drive. Why? A. If you are recording on mot ion only, you need to turn ON Permanent recordi ng opti on from record setting menu and per[...]

Q. What is the maximum cable distance for coaxial cable? RG59 Mini 22AWG Solid wire 200 ft (approximately) RG59/U 20 AWG Solid wire 750 ft (approximately) RG6/U 18 AWG Solid wire 1000 ft (approximately) RG 11/U 14 AWG Solid wire 1500 ft (approximately) Q. What is the maximum distance I can run 24V AC? A . The maximum distance dep ends o n the wire [...]

[...]

EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, European Office: Hsi-Chi, Taipei, Taiwan Albert-Einstein-Strasse 1, Phone: 886 (0) 2-269823 34 D-46446 Emmerich, Germany Fax: 886 (0) 2-26982380 Tel: 49 (0) 2822-93940 Web: http://www.EverFocus.com.tw/ Fax: 49 (0) 2822-939495 Web: http://www.EverFocus.de US (West Coast) Of[...]