Extron electronic JMP 9600 manuel d'utilisation

User Guide JMP 9600 Streaming A V Products T wo-Channel JPEG 2000 HD Video Player 68-1943-01 Rev . A 01 12[...]

This symbol is intended to alert the user of important operating and mainte- nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions ?[...]

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference r eceived, including interference that may caus[...]

Conventions Used in this Guide In this user guide, the following are used: CAUTION: A caution indicates a potential hazard to equipment or data. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier . WARNING: A warning war ns of things or actions that might cause injury [...]

Contents Introduction ............................................ 1 About this Guide ............................................. 1 About the JMP 9600 ........................................ 1 Features ........................................................... 3 Installation .............................................. 6 Mounting the Media Pl[...]

Mounting and Maintenance ............... 100 Mounting the Media Player .......................... 100 V entilation Guidelines .............................. 100 T abletop Use ............................................ 100 Rack Mounting ........................................ 100 Cleaning the Air Filters ................................. 102 Chan[...]

Intr oduction • About this Guide • About the JMP 9600 • Features About this Guide This guide contains installation, configuration, and operating information for the following Extron ® media players: • JMP 9600 HD – JPEG 2000 Media Player HD • JMP 9600 HD 128 – JPEG 2000 Media Player HD 128 GB SSD • JMP 9600 2K – JPEG 2000 Media [...]

INPUT: 100-240VAC, 0.4-1A, 50/60HZ USE ONLY: F2 AH 240V FUSES. 1-2 3-4 5-6 7-8 DIGITAL VIDEO OUTPUTS DIGITAL INPUTS RELAY OUTPUTS 1 2 3 4 + - + - + - + - 12V DIGITAL AUDIO OUT HDSDI DVI-I-1 1 2 DVI-I-2 JMP 9600 9-10 11-12 13-14 15-16 1 LAN 2 REMOTE 1 GENLOCK POWER LOCK LTC IN OUT OUT IN REMOTE 2 INPUT: 100-240VAC, 0.4-1A, 50/60HZ USE ONLY: F2 AH 24[...]

Featur es Digital video outputs: HD-SDI or DVI-I — • T wo DVI-I outputs — One connector per output channel supports 8-bit 4:2:2 sampled RGB or YCrCb. • T wo HD-SDI outputs — Can be configured as one dual link HD-SDI output or two single link HD-SDI outputs (one per channel — two single link outputs are available in 1-channel outp[...]

Operational reliability — Dual r edundant power supplies support round-the-clock operation in mission-critical applications. • T wo AC power inputs — Support the media player through any power interruption short of a simultaneous loss of power on both power sources. • T wo power input circuits — The two complete power circuits, fr om the [...]

Linear Time Code feature — Supports strict system timing contr ol. ESGEN and MSGEN Genlock capability — JMP 9600 2K units are capable of multi-unit synchronous operation. NOTE: ESGEN and MSGEN Genlock are pr oprietary sync signals that are native to Electrosonic ® pr oducts that have been acquired by Extr on and to older Electrosonic pr oducts[...]

Installation This sections details the installation of the JMP 9600, including: • Mounting the Media Player • Connections and Features Mounting the Media Player CAUTION: Installation and service must be performed by authorized personnel only . Detailed mounting instructions can be found in the “ Mounting and Maintenance “ section. The 2U hi[...]

Video and Audio Outputs a Digital Video Outputs, DVI-I connectors — Connect one or two DVI displays to the DVI-I-1 and DVI-I-2 connectors for the direct digital image and RGB video output. Figure 5 denes the pinout for the DVI pr otocol. Pin Signal 1 TMDS data 2– TMDS data 2+ TMDS data 1– TMDS data 1+ DDC clock +5 V power DDC dat aT MDS cl[...]

Sync In sync-critical applications, the media player can use one of two possible external sync signals, Genlock or Lock, in addition to the always-available Linear Time Code (L TC), to synchronize itself with other devices within a larger system. The media player can generate two of the sync signals to other devices. NOTES: • Use only one of the [...]

LAN Ports g LAN ports — If desired, for IP contr ol of the media player and content transfer , connect the player to a PC or to an Ethernet LAN, via either of these RJ-45 connectors. Y ou can use a PC to control the networked player with MSVPP commands from anywher e in the world. Y ou can also control the player fr om any PC via the built-in HTM[...]

RJ-45 connector wiring The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (see figur e 6 ). • Crossover cable — Dir ect connection between the computer and the media player • Patch (straight) cable — Connection of the media player to an Ethernet LAN A c[...]

Digital Inputs and Relays The Digital Inputs and Relays ports provides optically-isolated digital inputs and r elay outputs that can be controlled by the show contr ol software. See the “ Pr ogramming Guide “ section for the MSVPP commands that activate or are issued by the these ports. NOTES: • By factory default, automatic reporting of Digi[...]

Power NOTE: Although the unit performs reliably while running on a single AC power supply , doing so defeats the dual-redundant power supply featur e. l Dual Redundant AC Power Input connectors — Connect a standard IEC power cor d between one rear panel AC Power Input connector and a 100 to 240 V AC, 50-60 Hz power source. Connect a second IEC po[...]

Operation This section describes the front panel operation of the JMP 9600, including: • Definitions • Front Panel Contr ols and Indicators • Menu System Overview Definitions The following terms, which apply to Extron media players, ar e used throughout this manual: • Digital Cinema Package (DCP) — A folder that contains all of the fil[...]

Pre-r oll period — A programmable interval befor e the presentation starts. As an example, pre-r oll might allow audience members to take their seats after an announcement that the show has begun. Post-roll period — A pr ogrammable interval after the presentation ends. Select the Stop At option to set a stop point for the timecode and for the s[...]

T ransport Buttons d Play/Pause ( ) button — Press this button to start the curr ently selected CPL or clip file or pause a currently playing pr esentation while leaving the image displayed. e Stop ( ) button — Press this button to stop the curr ently playing presentation. When you press Play again, the pr esentation starts over from the begin[...]

Menu System Overview Power -on Sequence Plug either or both power cords into power sour ces and turn on ( ) one or both rear panel power switches. When AC power is applied, the media player performs a self-test that blinks all of the front panel buttons several times and then displays the LCD start-up scr een while it continues to load the operatin[...]

Channel status menus NOTES: • Channel 2 Status is displayed in the main menu (figure 10 ) and available for selection only in 2-channel output mode and 2-channel locked output mode, both of which can be selected in the Settings > Video submenu . • The Channel 1 Status and Channel 2 Status ar e identical, except where noted. Figure 11 shows [...]

Playlist and Clip fields These elds display whether a playlist or clip is loaded. Empty elds indicate that no playlist or clip is loaded. They also are used with menu contr ols to load a playlist or clip. Select and load a playlist or clip as follows: NOTES: • Y ou must have created one or mor e playlists using the HTML pages before any ar[...]

5. When loading a clip — The LCD displays the second step of the Select a clip file screen (see figur e 13 ). Proceed to step 6 . 5 Figure 13. Select a Clip File Scr een 6. Rotate the encoder knob as necessary to highlight the desired clip file. 7. Press the Enter button. The LCD r eturns to the Channel Status screen with the clip selected in [...]

Loop selection In Loop mode, the player runs the selected playlist or clip file in a continuous loop, automatically starting the presentation over again once it ends. T o toggle Loop mode on and off, r otate the encoder knob to highlight (box) the Loop selection and press the Enter button. Mute selection T o toggle audio mute on and off, rotate th[...]

Audio submenu The Audio submenu (see figure 15 ) pr ovides controls to set the volume and audio delay variables for the one or two output groups. Media player set to 2-channel or 2-channel locked output Media player set to 1-channel output Figure 15. Audio Submenu NOTE: The image shown on the left in figure 15 shows the audio menu when the media [...]

Autostart submenu NOTES: • The player must be correctly configur ed for the clip or playlist that you select using the Settings > Video submenu , or else the player does not load the selected clip or playlist and the LCD reports ERROR. • If you cannot get a clip to load, see “ Setting the clip or playlist to autoplay and view clip info ?[...]

7. T o select or change the clip or playlist that is displayed in the field beneath the radio buttons, rotate the encoder button to highlight the field (see figur e 17 ). 7 9 ENTER 8 ENTER 10 9 Figure 17. Select a Clip File Scr een 8. Press the Enter button. The eld displays a list of available playlists or clips, depending on the selection m[...]

Adjust the date and time as follows: 1. Rotate the encoder knob to highlight the first variable to be changed. NOTE: Rotating the encoder knob selects through the variables in the following order: Month > Day > Y ear > Hour > Minute > Second >Month ... . 2. Press the Enter button. 3. Rotate the encoder to change the selected vari[...]

Slider -type controls — The GUI/Video control adjusts the mix of the video image and the graphical user interface (the “alpha blend”). The Brightness and Contrast controls function the same as similar controls on any video monitor . Adjust the display controls as follows: 1. Rotate the encoder to highlight the desired variable. 2. Press the E[...]

Network parameters — The IP field contains the IP address of one the two the media player ports. The Netmask field is used to determine whether the media player is on the same subnet as the controlling PC when you ar e subnetting (see “ Subnetting — A Primer “ for more information). The Gateway IP Address field identifies the addr ess i[...]

1. Rotate the encoder to highlight the selection for the value or setting to be change ( a on figure 22 on the pr eceding page ): IP address — Interface 1 or 2, as applicable Netmask 1 or 2 — Interface 1 or 2, as applicable DHCP — Interface 1 or 2, as applicable Gateway — Gateway 2. Press the Enter button ( b ). NOTES: • If DHCP is enabl[...]

Ping function — Use the Ping function to ‘ping’ another device on the network as follows: 1. Rotate the encoder to highlight the Ping IP selection (see a on figure 23 ). ENTER 3 4 1 5 ENTER 6 2 Figure 23. Ping Function 2. Press the Enter button ( b ). 3. Rotate the encoder to highlight the first or next octet that needs to be changed ( c ).[...]

4. Press the Enter button ( d ). 5. Repeat steps 3 and 4 until the name or location is spelled out. 6. Press the Pr evious button to save the value and return to the Player submenu ( e ). 7. As desired, r epeat steps 1 through 6 for the other identifier . Reboot submenu The Reboot submenu (see figure 25 ) pr ovides a prompt that allows you to r e[...]

Configure serial port Remote 1 as follows: 1. Press the Enter button (see a on figur e 26 ). The Com port 1 configuration screen appears. 2. Rotate the encoder to highlight the value to be set: Mode, Baud Rate, Data Bits, Parity , or Stop Bits ( b ). 3. Press the Enter button. 4. Rotate the encoder to select the desired setting ( c ). See the no[...]

Video submenu The Video submenu provides tools to manage the video output settings and timing (see figure 28 ). NOTES: • Analog Channel 2 is displayed in the Video submenu (see gure 28 ) and available for selection only in 2-channel output mode and 2-channel locked output mode, both of which can be selected in the Settings > Video > Mod[...]

GenLock Selection HDSDI Selection Mode Selection Timecode Selection NOTES: • See page 3 for detailed descriptions of the functions of the modes. • The loop selections are indepen- dent of each other; you can select one, both, or neither . • Ch. 2 loop enabled is only available for selection when the switcher is in either 2-channel mode or 2-c[...]

Lock menu The Lock submenu allows the user to lock the front panel of the media player , limiting media player operation by unauthorized personnel. When the player is locked, all of the front panel functions are disabled except for the ability to unlock it. The player does not r espond to an other front panel operation. The lock is pr otected by a [...]

Help menu View contact information for Extron (see gur e 31 ). Figure 31. Help Scr een System Status menu View voltage and temperature information within the media player (see gur e 32 ). Figure 32. System Status Scr een V oltages should be in the following ranges to ensure optimum operation: • 3.3 V : +3.2 to +3.4 V • 5.0 V: +4.75 to +5.[...]

3. Press the Enter button ( b ). An alphanumeric keyboar d opens. 4. Rotate the encoder to highlight the first or next character in the password ( c ). NOTES: • is the back space key . Pressing Enter when this key is highlighted, causes erases the character to the left of the cursor . • is the Caps key . Pressing Enter when this key is highlig[...]

Play a Presentation Play a presentation as follows: 1. Rotate the encoder to highlight the Ch. 1 Status selection or Ch. 2. Status selection (depending on which channel you want to output the video). 2. Press the Enter button. The selected Channel Status menu opens. 3. Select and load a playlist as described in “ Playlist and Clip fields .” Th[...]

HTML Operation This section describes the operation of the JMP 9600 Media Player using its embedded HTML pages, including: • Opening the Embedded HTML Pages • Player Control Page • Playlist Editor Page • Setup Functions The player can be controlled and operated thr ough either LAN port, connected via a LAN or W AN, using a web browser such [...]

Opening the Embedded HTML Pages Access the player using HTML pages as follows: 1. Start the web browser pr ogram. 2. Click in the Address field of the browser . 3. Enter the IP address of the connected port in the Addr ess eld of the browser . NOTE: • If the local system administrators have not changed the value, the factory-specified defaul[...]

Channel 1 and 2 Control and Status Windows The Channel Control panel portion of the Player Contr ol page consists of one or two control and status windows that display information unique to the output channels. NOTES: • The Channel 2 control and status window is displayed only in 2-channel output mode and 2-channel locked output mode, both of whi[...]

T ransport controls Figure 37. T ransport Controls TIP: Rest the mouse over a control to see a pop-up tool tip that identifies the contr ol, as shown by the pop-up in figure 37 . Progr ess bar — This bar tracks the progr ess of a clip in play . If the clip is paused, the progr ess bar freezes; if the clip is stopped the pr ogress bar goes blank[...]

Loading a Clip or Playlist into a Player Channel NOTES: • Y ou must have created one or mor e playlists before any ar e available for selection to select (see “ Playlist Editor Page “). • Ensure that the media player is configur ed for 1-channel output before attempting to load 4:4:4 chroma subsamped or ster eoscopic content. If the player[...]

Setting the clip or playlist to autoplay and view clip info NOTE: • The player must be correctly configur ed for the clip or playlist that you select using the Setup > Video > Mode dialog box submenu , or else the player does not load the selected clip or playlist. • If you cannot get a clip to load, See “ Setting the clip or playlist [...]

Playlist Editor Page The Playlist Editor page (see gure 40 ) is the default startup page, appearing when you initially download the web pages from the player . From the Playlist Editor page, click the Playlist Editor link at the top right of the page. The Player control page consists the Playlist Br owser , Playlist Editor , and Clip Browser pan[...]

Editing the Contents of a Playlist T o perform all of the playlist editing functions described in the various procedures below , you must open the playlist in the Playlist Editor panel. Open the desired playlist by clicking its name in the Playlist Br owser panel. The name of the playlist appears in the Edit Playlist panel header and the clip le[...]

Remove a clip file from a playlist 1. In the Playlist Editor panel, left-click the le that you want to remove fr om the playlist (see a in figure 45 ). TIP: Hold down the <Ctrl> key to select multiple clip files. 4 3 2 1 Figure 45. Removing Clips fr om a Playlist 2. Right -click anywhere over the clip les listed in the Playlist Edito[...]

Editing the Properties of a Playlist NOTE: See “ Synchronization “ and “ Configuring a player as an L TC master “ in the “Detailed System Interaction” section for a detailed discussion of the JMP 9600 timecode feature, its interaction with other timing r eferences and system components, and specific application examples. Y ou can edit[...]

Setup Functions A wide variety of communications, video, and audio setup functions, necessary to ensure peak performance of the player and the video/audio playback, are available using the Setup palette of tools (see figur e 47 ). T o select the setup functions, from the Playlist Editor page, click the Setup Editor link at the top right of the pag[...]

Autoplay Setup Dialog Box The Autoplay setup dialog box (see figure 49 ) displays of the complete path of a clip file selected to autoplay in each channel and buttons to clear an autoplay selection. Figure 49. Autoplay Setup Dialog Box NOTE: This dialog box lets you view and clear an autoplay selection only . T o set a clip file to autoplay , se[...]

Network Ethernet setup dialog boxes 1. Select Network > Ethernet 1 or Network > Ethernet 2 to open the selected Ethernet setup dialog box (see gure 50 ). Figure 50. Ethernet Setup Dialog Box 2. For the IP Address and Netmask (subnet mask) fields: a. Click in the desired field. b. Edit the address as desir ed. 3. Click the Mode drop-down [...]

License Management Setup Dialog Box The License Management setup dialog box (see figure 52 ) allows the user to see the installed license and enter an acquired pr oduct license, unlocking the capabilities supported by that key . 3 1 2 Figure 52. Enter a License Key 1. Obtain the license key from Extr on. 2. Click the Install New License button (se[...]

Serial Port Setup Dialog Box The Serial Port setup dialog box provides tools to configur e serial port Remote 1 (see figure 54 ). 1 2 3 4 5 6 7 1 Figure 54. Serial Port Setup Dialog Box Submenu NOTES: • Serial port Remote 1 can be set to disabled , controlmsvpp (control the player), or passthrough (pass the signals through the player to a contr[...]

Video Setup Dialog Boxes The Video selection provides pages to set up the media player for best video performance. Use these pages to set the number of channels the player outputs, congure the video outputs (analog, DVI-I, or HD-SDI), set the video colorspace, and congure video synchronization. Video mode setup dialog box Figure 55. Video Mod[...]

Genlock drop-down box — Select among the genlock modes shown at right. The green bar in the field indicates that your selection is being saved. Black Burst P AL and Black Burst NTSC — Receive a selected sync signal. ES Genlock and ES MS9200 Genlock — Receive ES Genlock or MS9200 Genlock as a slave. NOTES: • ES Genlock and ES MS9200 Genlock[...]

HDSDI Mode — Select between the output * * * * These selections are av ailable in 1 channel mode onl y. modes shown at right. The green bar in the field indicates that your selection is being saved. NOTES: • The Dual Link High Framerate, available on the JMP 9600 2K model only , supports resolutions of up to 1920x1080 and 2048x1080 at 48, 50, [...]

Pr ogramming Guide This section describes MSVPP command control of the JMP 9600 Media Player , including: • Control Ports • Host-to-Player instructions • Using the Command and Response T able Contr ol Ports The media player has three r emote control ports make r emote control of the player possible: Remote port 1 — An RS-232 port on a 9-pin[...]

Default IP Addresses T o access the media player via either LAN port, you need the IP address for the port that you are using, and may need the netmask mask and the gateway addr ess. The factory-specified defaults are: • IP address (port 1): 192.168.254.254 • IP addr ess (port 2): 192.168.254.253 • Netmask mask: 255.255.0.0 • Gateway addre[...]

5. Enter valid MSVPP commands (see “ Command and Response T able for MSVPP Commands “) in the Command eld and press the keyboar d <Enter> key . The media player responds accor dingly . TIPS: • Previous commands ar e available using the drop-down list of the Command field (click ). • If you enter a folder or file name with the wro[...]

Using the Command and Response T able Symbols (parameters), defined below , are used thr oughout the Command and Response T able for MSVPP Commands , which begins on page 60. The symbols represent variables in the command/response table fields. Letters in the command field ar e not case-sensitive. Hexadecimal equivalent are not necessary for the[...]

X2! = HD-SDI enable state 0 = not enabled, 1 = enabled X2@ = HD-SDI mode “single”, “dual_422_12”, “dual_444_10“, or “dual_444_12“ or “dual_422_hfr“ NOTES: • The “dual_422_hfr ” high frame rate is a licensed option of the JMP 9600 2K model. • The high frame rate supports resolutions of up to 1920x1080 and 2048x1080 at 48,[...]

Command MSVPP Command (host to unit) Response (unit to host) Additional description Media management View directory GetMediaTree } MediaBranch • 1 • X! ] MediaBranch • 1 • X! ] • • • • MediaBranch • 1 • X! ] MediaBranch ] List all DCP folders (clips and playlist) saved in the media player . Example: GetMediaTree } MediaBranch ?[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Media management (continued) Load the next clip to play LoadNextClip • X# • X! / X@} OK ] Load a clip to play automatically after the clip that is currently playing in channel X# ends. If X! and X@ ar e not v[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Media management (continued) Append a clip to a playlist AddPlaylist • X$ • X! / X@} OK ] Add the clip file X@ , in the folder X! , to playlist X$ . The file cited in the command is added as the last clip i[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Media management (continued) Switch to a new playlist SwitchPlaylist • X# • X$} OK ] Set playlist X$ to start automatically on channel X# once the currently-running clip ends. Example: SwitchPlaylist • 1 ?[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Playlist properties NOTE : Property names are case sensitive. Set playlist properties SetPlaylistProperties • X$ • X( • X1)} OK ] Set the property X( to a value of X1) for playlist X$ . Include multiple pro[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Timecode commands NOTES: • Immediately after loading a clip, the playlist property times takes precedence. If you load a clip then send a tcplayat command, that command takes pr ecedence. • Timecode ( X* ) va[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Colorspace NOTES: • The player must be correctly configured for the colorspace that you select, or else the player r esponds with ERROR . • Y ou can configure the media player signal combinations that ar e no[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Sync NOTES: • Media players with serial numbers 9600-01 through 9600-50 support the master , esgen, and esgenlegacy sync types only . See “ About menu ” in the “Operation” section to identify the serial[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Audio mute NOTE: Audio is unmuted (is output) when power is cycled. Mute the audio SetAudioMute • X# • 1 } OK ] Mute disables the audio output from all 16 audio channels when the media player is in 1-channel [...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Serial port Remote 1 configuration NOTES: • Serial port Remote 2 is not configurable. It is for factory use only . • Y ou can set the serial port conguration and mode via an MSVPP command and connected t[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Ethernet configuration (continued) Set gateway address SetGateway • X3@ • X3#} OK ] Set the gateway addr ess of port X3@ to X3# . The Ethernet port ( X3@ ) must be connected to a server or else the media pla[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Time of day Set the date and time SetDate • X3* • X3(} OK ] Example SetDate • 10/15/2010 • 10:20:00 } OK ] View the date and time GetDate } Date • X3* • X3( ] Device parameters NOTE: If there ar e spa[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Information requests TIP: Copy the folder and filename in the response to the view current clip and view curr ent playlist commands to the clipboard of your computer to paste them into scripts or DataViewer Send[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Information requests (continued) View position (frame count) GetStateEx • X# • Position } StateEx • X# • ”position” • ” X4& ” ] StateEx ] Show the position of the currently-loaded clip (or c[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Information requests (continued) View front panel temperature GetTemperature • Front • Panel } Temperature • ”front • panel” • X4( C ] Temperature ] Show the front panel temperatur e in degrees Cels[...]

Command/response table for MSVPP commands (continued) Command MSVPP Command (host to unit) Response (unit to host) Additional description Information requests (continued) View disk information GetDiskInfo } diskinfo • X4! total • X4! free ] Show the total capacity of the hard drives ( X4! total )and the amount of free space ( X4! free ). The r [...]

Detailed System Interaction This section describes the interaction of the media player and other system components at a detailed level, including: • Data T ransfer and Firmware Upgrade • Synchronization • Using Digital Inputs and Relays • Encoding Guidelines Data T ransfer and Firmware Upgrade NOTE: The media player must run firmware versi[...]

3. Enter the IP address of the connected port in the Host eld (see d on figur e 60 ). NOTE: If the local system administrators have not changed the value, the factory- specified default IP addresses ar e as follows: LAN 1 : 192.168.254.254 LAN 2 : 192.168.254.253 4. Enter “ es9600 ” (without the quotes) in the Username eld ( b ). NOTE: [...]

Loading Media Folders to the Media Player See “ Encoding Guidelines ” details on encoding content for use on the JMP 9600. The nal encoded content (JPEG 2000 video, audio, and other associated data) is collectively referr ed to as a DCP folder and must be loaded on the hard drive of the JMP 9600 via FTP in order to be played. 1. Connect a co[...]

Deleting Folders and Individual Files from the Media Player 1. Connect a computer to the media player and start the FTP utility (see “ Starting the FileZilla FTP Utility ” on the page 76 ). 2. Left-click the folders and files that you want to delete (see a figure 63 ). TIP: Hold down the <Shift> key to select multiple folders or les.[...]

Loading and Updating firmware NOTE: The media player must run firmware version 2.06.07 or newer to pr operly update to even newer versions. If you have version 2.06.06 or older , you must update to 2.06.07 before updating to any later version. See “ About menu “ in the “Operation” section to determine your firmware version. Acquire firm[...]

6 4 5 4 Fo lder where firmware is installed NOTE: The file name and size shown are sample values only . Figure 65. Downloading Firmwar e Upgrade Files JMP 9600 Media Player • Detailed System Interaction 81[...]

7. Connect a computer to the media player and start the FTP utility (see “ Starting the FileZilla FTP Utility ” on the page 73 ). 8. In the local site, navigate to the folder where you saved the firmwar e upgrade file (see a on figure 66 ). NOTE: V alid rmware les must have the le extension .UPG. A le with any other extension is [...]

Synchr onization Large control systems often r equire a number of dif ferent pieces of equipment to operate within strict timing constraints. For example, an exhibit can use a video display with an associated multi-channel audio playback system, in which audio playback must match the video display (“lip sync”). T o support complex system timing[...]

Connections for Synchronized Multi-player Operation The following equipment is requir ed for an example of a small synchronized system: • T wo JMP 9600 Media Players (see figure 67 , below) • One or more L TC cables terminated with male RCA connectors (in re d on figure 67 ) • One or more Lock (ESGEN or MSGEN genlock) cables terminated with[...]

If the slave player needs an additional timing refer ence for more pr ecise synchronization (see “ Results of timecode and genlock timing refer ences ,“ below), either the proprietary genlock timing r eference or traditionaly genlock can pr ovide it. In figure 67 , on the preceding page, the master player outputs the ESGen genlock signal on it[...]

ESGEN vs. traditional Genlock The example in figure 67 , on page 84, uses ESGEN Genlock. T raditional genlock, such as is output by an Extron BBG 6 A Blackburst Generator , can also be used in many applications. See the attributes of the two timing refer ences, below , to determine which to use in your application. ESGEN Genlock attibutes — • [...]

Applicable MSVPP commands The table below lists the MSVPP commands that you may need to congure and contr ol a multi-player system. With the exception of TCStart , which can only be an MSVPP command (see the first NOTE , below), all of these commands can be also be accomplished using the HTML pages, as shown in the “ Configuring L TC for Syn[...]

TIP: When you are in a multiple player , master/slave conguration, you should stop all slave players before loading new content on the master player if that content has a differ ent frame rate than the currently-loaded content. 1. Stop all players. 2. Load new content on the master player . 3. Load new content on the slave players. 4. Send the t[...]

L TC locks any slave devices to the video output of the master player . Each playlist can have its own unique L TC and has the ability to generate a pre-r oll period, a post-roll period (also called “run-on”), or both. The simplest way to congure the player is using the HTML Edit Playlist Pr operties dialog box as shown in the “ Configuri[...]

Figure 69 shows using the Edit Playlist Pr operties dialog box to set the master player to generate an L TC ( a ) that starts counting up from 01:00:00:00 (exactly 1 hour) ( b ) once the play or TCStart command is received. 2 1 Figure 69. Generate an L TC Figure 70 shows using the Edit Playlist Pr operties dialog box to generate an L TC that starts[...]

Configuring a player as an L TC receiver (slave) A slave player can be programmed to begin playing the loaded clip or playlist when it receives a particular L TC timestamp. A different L TC timestamp can be programmed for each clip in a playlist. Figure 72 shows using the Edit Playlist Pr operties dialog box to receive an L TC ( a ), start the vid[...]

Configuring Genlock for Synchronized Multi-player Operation Genlock ensures that multiple media players operate with synchr onous timing on each of their outputs. Genlock synchronizes and locks the video outputs. When genlock is combined with the L TC refer ence, the first frame of video is decoded across all the players that make up the ‘genlo[...]

High Frame Rate The high frame rate mode supports resolutions of 1920x1080 and 2048x1080 at 48, 50, and 60Hz by using the dual HD-SDI connection mode. The media player must be set for 2-channel-locked mode and the content must be progr essive frame only with interlaced transport format, compatible with SMPTE 372-2009. The high frame rate content re[...]

Optically-isolated Digital Inputs The digital input connections are implemented as four + and – terminals on 3.5 mm captive screw terminal blocks. Because each input is optically-isolated, both connections must be used to ensure the corr ect operation of the input circuit. NOTE: By factory default, status notication for Digital Inputs 1 throug[...]

Relay Contacts The relay outputs consist of four sets of NO and NC r elay contacts. Connect an external device that you want to be able to switch on or off to the player via thr ee poles (normally closed [NC], common [C], and normally open [NO]) of the 3.5 mm 4-pole captive screw connectors. NOTE: Relays R1 and R4 each span three poles on a single [...]

Encoding Guidelines This section describes the process of encoding and packaging a video and audio pr esentation for playback on the JMP 9600 Media Player . The Extron JPEG 2000 Encoder softwar e simplifies and optimizes the process and workflow for creating content. T wo versions of the software ar e included on the DVD that shipped with the med[...]

Encoding and Packaging Overview Creating content for the JMP 9600 is done in thr ee stages: encoding, wrapping and packaging. The Extron JPEG 200 Encoder Softwar e performs these tasks automatically and internally (see figure 78 ). This process is pr ovided for refer ence only . a.wav J2C Frame J2C Frame ... J2C Frame Imag e Frame Imag e Frame ...[...]

Composition playlist A composition playlist (CPL) is a text file that contains all of the information necessary to reassemble a pr esentation from its individually encoded components and how the files for a specific presentation should be played back. The CPL file points to the r eels (see figure 79 ), identifying locations (folders) and file[...]

JPEG-2000 Restrictions The stream of JPEG-2000-coded frames must conform to ISO 15444-1:2004/PDAM 1 and are further constrained as follows: • All frames must be untiled; the entire image is encoded as a single tile. • The image and tile origins must both be at <0,0>. • Each compressed frame must be less than 1,300,000 bytes. • Each ti[...]

Mounting and Maintenance This section details the following JMP 9600 Media Player procedur es: • Mounting the Media Player • Cleaning the Air Filters • Changing Fuses • Battery Precautions Mounting the Media Player The JMP 9600 Media Player is housed in a rack-mountable, 2U high metal enclosure. It can be set on a tabletop or installed in a[...]

2. Reduced air flow — Installation of the equipment in a rack should be such that the amount of air ow requir ed for safe operation of the equipment is not compromised. 3. Mechanical loading — Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. 4. Circuit overload[...]

Cleaning the Air Filters The JMP 9600 is equipped with two foam air filters that should be checked every four to six months and cleaned or replaced as r equired. Y ou may need to perform this check more frequently in envir onments containing higher levels of particulates (such as dust). CAUTION: Do not subject the player to excessively dusty envir[...]

Changing the Fuses The JMP 9600 is equipped with field replaceable fuses to pr otect against overcurr ent damage. If one of the two power circuits fails, r eplace the fuses as follows: WARNING : Physically disconnect both power cables from the player befor e removing the fuse module. CAUTION: This unit employs double pole/neutral fusing. 1. Unplug[...]

T roubleshooting a High T emperature The internal temperature of the media player can be viewed on the front panel (see “ System Status menu “ in the “Operation” section. T emperatures above 85 °C (185 °F) indicate an equipment cooling problem. Power of f the media player and troubleshoot a high temperature as follows: 1. V erify that the[...]

Ether net Connection This section provides a high level discussion of the Ethernet connections on the player and a primer on the subject of subnetting. T opics that are covered, include: • Ethernet Link • Subnetting — A Primer Ether net Link The rear panel Ethernet connector on the switcher can be connected to an Ethernet LAN or W AN (see ite[...]

Pinging to Determine the IP Address The ping utility is available at the Command prompt. Ping tests the Ethernet interface between the computer and the media player . Ping can also be used to determine the actual numeric IP address fr om an alias and to determine the web address. Ping the player as follows: 1. On the Windows task bar , click on Sta[...]

Configuring the Media Player for Network use via the ARP Command The ARP (address r esolution protocol) command tells your computer to associate the media MAC (media access control) addr ess of the player with the assigned IP address. Y ou must then use the ping utility to access the controller , at which point the IP address of the controller is [...]

Connecting as a T elnet Client NOTE: The T elnet Client utility is not installed by default in Microsoft Windows 7 or W indows V ista. Click Start > Search and type pkmgr/iu:”TelnetClient” <Enter> on the Start Search line. The T elnet utility is available from the Command prompt. T elnet allows you to input MSVPP commands to the media [...]

Set carriage return-line feed Unless commanded otherwise, T elnet transmits a line feed character only (no carriage return) to the connected player when you press the <Enter> key . This is the correct setting for MSVPP communication with the player . The T elnet set crlf command forces T elnet to transmit carriage return and line feed charact[...]

Subnet Masks and Octets The subnet mask (figure 86 ) is used to determine whether the local and r emote devices are on the same subnet or differ ent subnets. The subnet mask consists of four numeric octets separated by dots. Each octet can be numbered fr om 000 through 255. Leading zer oes, up to three digits total per octet, ar e optional. Each o[...]

Refer ence Information This section discusses the specifications, part numbers, and accessories for the JMP 9600 Media Player . T opics that are covered include: • Specifications • Part Numbers Specifications Content/file format File types ........................................ MXF-wrapped JPEG 2000 in DCP (Digital Cinema Package, unencry[...]

Player sync External sync in (genlock) ............... 1 Vp-p, bi-level or tri-level Genlock connectors ........................ 1 female BNC (genlock in, black burst) 2 female 6-pin mini DIN (LOCK proprietary genlock in and out, for connection to other JMP 9600 units) Time code Signal level ..................................... Input impedance: 60[...]

Digital I/O control Number/type .................................. 4 digital inputs 4 relay outputs (2) 12 VDC outputs Connectors Digital inputs ........................... (2) 3.5 mm captive screw connectors, 4 pole Relay outputs ........................... (3) 3.5 mm captive screw connectors, 4 pole Power ...................................... (1[...]

Part Numbers JMP 9600 Part Numbers Media player part numbers Part number JMP 9600 HD – JPEG 2000 Media Player HD 60-1135-01 JMP 9600 HD 128 – JPEG 2000 Media Player HD 128 GB SSD 60-1135-02 JMP 9600 2K – JPEG 2000 Media Player 2K 60-1136-01 JMP 9600 2K 128 – JPEG 2000 Media Player 2K 128 GB SSD 60-1136-02 Included Parts These items are incl[...]

Cables When using signals with a scanning frequency of 15-125 kHz and running distances of 100 feet or more, use high r esolution BNC cables to achieve maximum performance. Cable assemblies Cable Part number DVID SL Pro Series DVI-D Male-to-Male Cable 26-649- nn HDMI M-M Pro Series HDMI Male to Male Cable 26-650- nn HDMI M-DVI-D M/6 HDMI Male to DV[...]

Extr on W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of thr ee years from the date of pur chase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electr onics will, at its option, repair or r eplace said produc[...]