Ford 2007 Escape manuel d'utilisation

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Entertainment Systems 19 AM/FM stereo with in-dash six CD 19 AM/FM stereo with CD/MP3 28 AM/FM stereo cassette with CD 32 Climate Controls 39 Heater only 39 Manual heating and air conditioning 40 Rear window defroster 41 Lights 42 Headlamps 42 T urn signal control 47 Bulb [...]

Seating and Safety Restraints 89 Seating 89 Safety restraints 97 Airbags 112 Child restraints 127 Tires, Wheels and Loading 139 T ire Information 141 T ire Inflation 143 T ire Pressure Monitoring System (TPMS) 156 V ehicle loading 160 T railer towing 166 Recreational towing 171 Driving 172 Starting 172 Brakes 175 T ransmission operation 178 Roadsid[...]

Maintenance and Specifications 240 Engine compartment 242 Engine oil 245 Battery 249 Engine Coolant 251 Fuel information 257 Air filter(s) 271 Part numbers 273 Maintenance product specifications and capacities 274 Engine data 277 Accessories 280 Index 282 All rights reserved. Reproduction by any means, electronic or mechanical including photocopyin[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

BREAKING-IN YOUR VEHICLE Y our vehicle does not need an extensive break-in. T ry not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. V ary your speed frequently in order to give the moving parts a chance to break in. Drive your new vehicle at least 500 miles (800 km) before towing a trailer . F[...]

Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and ser[...]

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’ s Guide carefully . Y our vehicle is not a passenger car . As with other vehicles of this type, failure to operate this vehicle correctly may re[...]

Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’ s Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfuncti[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter . W ithout message center W ith message center Brake system warning light: To confirm the brake system wa[...]

Airbag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A BeltMinder 威[...]

Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains ON at start up or while driving, the tire pressure should be checked. Refer to Inflating Y our T ires in the T ires, Wheels and Loading chapter . When the ignition is first turned to ON, the light will illuminate for 3 seconds to ensure the bulb is working.[...]

Door ajar: Illuminates when the ignition is in the ON position and any door is open. W ithout message center W ith message center Displays which door , liftgate or liftgate glass is open. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster , check for a burned ou[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the e[...]

Odometer: Registers the total miles (kilometers) of the vehicle. T rip odometer: Registers the miles (kilometers) of individual journeys. T o reset, tap on the trip reset button to toggle the display between the trip and the odometer . Holding the reset button for one or two seconds will reset the trip odometer to zero. T achometer: Indicates the e[...]

AUDIO SYSTEMS Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3 Radio (if equipped) 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Entertainment Systems 19[...]

Audiophile Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3 Radio (if equipped) 1. SEEK: Press and release SEEK / for previous/next strong station or track. 2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display its c[...]

3. AUX: This function is not operational. 4. MUTE: Press to MUTE playing media; press again to return to playing media 5. EJ: Press to eject a CD. Press EJ and a memory preset to eject a specific disc. Press and hold to eject all loaded discs. 6. Bass: Press BASS; then press SEL / to decrease/increase the bass output. T reble: Press TREB; then pres[...]

stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. T raffic: Allows you to hear traffic broadcasts. W ith the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). T raffic information is not available in most[...]

Folder/T rack Mode: In MP3 mode, press MENU until MODE appears in the display . Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEA T : Repeats current CD/MP3 track when active (ON). Press to show repeat status. Press again to toggle status. 11. SHUFFLE: P[...]

19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. Load: Press to load a CD. Press LOAD and a memory preset to load to a specific disc slot. Press and hold to load up to six discs. 21. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to[...]

AM/FM stereo in-dash six CD modular audio (if equipped) 1. CD: T o begin CD play , press LOAD. When the system is ready to accept a disc, IN will appear on the radio display . Y ou may then insert a CD. The system will load the CD and begin play after a short pause. The disc number and track number will illuminate in the display . If a CD is alread[...]

2. AUTO — SCAN: AUTO: Auto memory tuning allows you to set strong radio stations without loosing your original manually set preset stations. Press the AM or FM1/2 control to select a frequency . Press and momentarily hold the AUTO-S control. The system will beep. When the first six strong stations are filled, the strongest station will start play[...]

Setting the clock: Press and hold CLK for approximately two seconds until a beep is heard. The clock’ s current time will flash. Press SCAN on the minute set control (M) to set the minutes. Press AUTO-S on the hour set control (H) to adjust the hours. Press CLK again to disengage clock mode. 6. FF (Fast forward): In CD mode, press and hold to adv[...]

15. SEEK — TRACK: In radio mode, press to find the next ( ) or previous ( ) listenable station on the frequency band. In CD mode, press to listen the next ( ) or previous ( ) track. 16. CD door: Insert CDs label side up. 17. FM 1/2: Press to enter FM mode. Press to toggle between FM1 and FM2. 18. AM: Press to enter AM mode. Satellite Compatible A[...]

2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display , its corresponding text indicator (Fi, So, Ar , or AL) is shown in the elapsed time display . Press TEXT to scroll through the text fields. The display will scroll t[...]

Fade: Press F ADE; then press SEL / to shift sound to the rear/front speakers. 9. Menu: Press MENU and SEL to access AUTOSET , Speed sensitive volume and Setting the clock. Autoset: Press MENU until AUTOSET appears in the display . Press SEL to toggle ON/OFF . Allows you to set the strongest local radio stations without losing your original manuall[...]

16. SA T (if equipped): Y our radio comes equipped with Satellite Ready capability . The kit to enable the Satellite reception is available through your dealer . Detailed satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 17. BAND: Press to toggle betwee[...]

23. CA T/T une: Press or to manually tune down/up the radio frequency band. CA T : CA T is only available when equipped with Satellite Radio. Y our radio comes equipped with Satellite ready capability . The kit to enable Satellite reception is available through your dealer . Detailed Satellite instructions are included with the dealer installed kit[...]

1. CD slot: Insert a CD with the label side up. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached[...]

7. MENU: Press to access the following functions: Clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Press SEL to decrease/ increase hours or minutes. Compression: In CD mode, press to bring soft and loud passages together for a more consistent listening level. Press MENU until COMPRESS is displayed. Use SEL to toggle on/off. Dolby:[...]

Fade: Press F ADE; then press SEL / to shift sound to the rear/front speakers. 10. SHUFFLE: In CD/MP3 mode, press to play tracks in random order . Press to show shuffle status. Press again to toggle status. 11. TEXT/SEL: The filename, song title, artist text or album text may be viewed while playing an MP3 selection. Press TEXT to scroll through th[...]

T reble: Press TREB; then press SEL / to decrease/increase the treble output. 15. Fast Forward (FF): In CD mode, press and hold to fast forward. In tape mode, press to activate fast forward. Press FF again to return to play . 16. Rewind (REW): In CD mode, press and hold to reverse CD. In tape mode, press to rewind. Press REW again to return to play[...]

23. Power/volume: Press to turn ON/OFF; turn to increase/decrease volume. GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 10[...]

CD/CD player care: Do: • Handle discs by their edges only . Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to p[...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outside air through the instrument panel vents. : Distributes outside air through the i[...]

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the follo[...]

• Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow , ice or leaves from the air intake area at the base of the windshield. T o aid in side window defogging/demisting in cold weather: 1. Select A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to 4. [...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after the ignition switch has been turned off if the headlamp control is in the position. The system will n[...]

Autolamp delay system (if equipped) If your vehicle has an autolamp delay feature, you can set the delay time to keep the headlights on for up to three minutes after the key is turned OFF . The delay time is set to 20 seconds at the factory , but the delay time may be changed by following the steps below (Steps 1 through 6 must be done within 10 se[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output. T o activate: • the ignition must be in the 3 (RUN) position. • the headlamp control must be in the OFF , parking lamps or autolamp position. • the parking brake must be[...]

Foglamp control (if equipped) Press the foglamp control, located on the instrument panel, to activate the foglamps. The foglamp indicator will illuminate when the foglamps are on. Press the foglamp control to deactivate the foglamps. The foglamps will only operate with the parking lamps or headlamps on. When the highbeams are activated, the foglamp[...]

• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The cente[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate. • DOOR: In th[...]

For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps. The map lamps will illuminate whenever a door is opened. After the door is shut, the lamps will remain illuminated for 25 seconds. Carg[...]

“E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time. Function Number of bulbs T rade number Park/turn lamps (front) 2 3157 AK (amber) Headlamps (low beams) 2 H11 Headlamps (high[...]

3. Locate the outboard most bulb, turn it a 1 ⁄ 4 turn to the inside of the vehicle and pull the bulb socket straight out to remove the bulb. Highbeam bulb replacement 4. Locate the bulb that is the most center in the vehicle, rotate the socket counterclockwise and pull the bulb socket straight out to remove the bulb. 5. Pull the bulb straight ou[...]

1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly . 3. Carefully remove the lamp assembly by pulling it rearward to disengage snap features on the outward side of the lamp. 4. T wist the bulb socket counterclockwise and remove from lamp a[...]

Replacing high-mount brake lamp bulbs T o remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in rev[...]

MUL TI-FUNCTION LEVER W indshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF . For high speed wiper operation, move control down three positions from OFF . Mist function: T o activate mist[...]

Rear window wiper/washer controls For intermittent operation of rear wiper , rotate end of control upward to the position. For normal speed rear wiper operation, rotate control upward to ON. T o activate the rear washer , rotate the control to the position and release. TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull down the steering col[...]

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may b[...]

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The auxiliary [...]

POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part [...]

Note: The passenger window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls. Accessory delay W ith accessory delay , the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition switch is turned to the OFF position[...]

Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror gl[...]

3. Press the SET ACC control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduc[...]

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET ACC control. Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST control until you get to the desired speed, then release the control. Y ou can also use the CST control to[...]

MOON ROOF (IF EQUIPPED) T o operate the moon roof: Note: The moon roof will open to the “comfort” position first before opening all the way . The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened. • The moon roof is equipped with an automatic, one-touch, express opening fe[...]

MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also n[...]

Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • [...]

Y our vehicle must be moving to calculate instantaneous fuel economy . When your vehicle is not moving, this function shows , one or no bars illuminated. Instantaneous fuel economy cannot be reset. Fuel available Selecting this function from the INFO menu will show you how much fuel is available in your tank. Units (English/Metric) 1. Select this f[...]

Language 1. Select this function from the INFO menu for the current language to be displayed. 2. Pressing the SET control cycles the message center through each of the language choices. 3. Press and hold the SET control for 2 seconds to set the language choice. Display Off Select this function from the INFO control to turn your message center displ[...]

W arnings Status High engine temperature W arning cannot be reset Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar Park brake on W arning returns after 10 minutes Liftgate ajar W arning returns after the ignition key is turned from OFF to ON. Service emission sys Check fuel cap Low brake fluid Low tire pressure T ire pr[...]

engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter . If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. Never remove the coolant reservoir cap while the engine is running or hot. DRIVER DOOR AJAR. Displayed when the driv[...]

SER VICE BRAKE SYSTEM. Displayed when the braking system is not operating properly . If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK LEFT OR RIGHT HEADLAMPS. Displayed when the headlamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned ou[...]

1. Select this function from the INFO menu then press the SET control to access the system check function. 2. Press and release the SET control to display “OIL CHNG XXX% HOLD SET NEW”. 3. Press and hold the SET control for 2 seconds to display “OIL CHANGE SET TO 100%”. INFO UNA V AIL. These messages indicate improper operation of the vehicl[...]

LIFTGATE T o open the rear window , pull the right side of the liftgate handle. T o open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be dama[...]

Ensure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is not securely installed. Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of a sudden stop or collision. Cargo management system (if equipped) The [...]

T o adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. T ighten the thumbwheel at both ends of the cross-bar . T o remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel a[...]

T o reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 3. Slide the cross-bar assemblies over the end cap t[...]

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer . Refer t[...]

7. T urn the ignition from the 3 (RUN) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking T wo step door unlocking 1. T urn the key in the door cylinder to unlock the driver’ s door . Note: The interior lamp[...]

Relock This feature will also automatically relock all the doors when: • the ignition is in the 3 (RUN) position and any door is opened then closed, and • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature The autolock feature can be turned on or off using the following procedure: Before sta[...]

CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatically set the lo[...]

The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote locking and unlocking features will operate independent of the ignition position; however , the panic feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACCESSORY) position. If there are problems with the remote entry system, make sur[...]

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapt[...]

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]

Note: Ensure the brake pedal is not depressed during this sequence. T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. T urn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: T[...]

Illuminated exit • The interior lights will illuminate when the key is removed from the ignition. The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate. KEYLESS ENTRY SYSTEM (IF EQUIPPED) Y ou can use the keyless entry keypad to lock or un[...]

T ips: • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . • The factory set code will work even if you have set your own personal code. • If you set a second personal code it will erase your first personal code. Note: T o exit programming mode, either wait 5 seconds after pressing 1 • 2[...]

program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key . Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss [...]

Programming spare keys Y ou can program your own coded keys to your vehicle. T ips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • Y ou must have two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible. • If two pr[...]

9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’ s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’ s engine and the theft indicator light will flash[...]

When you press the control on the remote entry transmitter twice within three seconds, the horn will chirp once to confirm the doors, liftgate and hood are closed and locked, and the alarm is set. Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transm[...]

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that ca[...]

Push side control and push down on head restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward. Pull lever up to adjust seatback. 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 90[...]

Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an[...]

Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) T o operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats w[...]

The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head. Push control to lower or remove head restraint. Folding down rear seats 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 2007 Escape (204) Owner[...]

3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button. This will ensure that safety belt does not get caught by staying out of the seat back folding path. 2007 Escape (204) Owners Guide (post-2002[...]

5. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. Note: When the seatback release lever is pulled, slowly lower seatback to the flat position. 6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback u[...]

2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the safety belt buckles are exposed. Make sure safety belt buckle heads are through elastic holders on seat backs. Safety belt buckles may break if they are trapped underneath the seatback as the seatback is rotated down. Before ret[...]

T o remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. Pull the cushion to the outboard side of the vehicle. T o install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provid[...]

• “Passenger airbag off” or “pass airbag off” indicator lamp • Front crash severity sensor . • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driv[...]

Driver ’ s seat position sensor The driver’ s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensi[...]

Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System 娂 to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety restraints sect[...]

If any of these things happen, even intermittently , have the Personal Safety System 娂 serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o r[...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder be[...]

All safety belts in the vehicle are combination lap and shoulder belts. The passenger safety belts have two types of locking modes described below: V ehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver bra[...]

• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retra[...]

Safety belt height adjustment Y our vehicle has safety belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down. Release the butt[...]

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is loca[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1 minute and the warning chime sounds 6 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... Th[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The BeltMinder 威 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the vehicl[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during[...]

Reasons given... Consider ... ⬙ The people I’m with don’t wear belts ⬙ Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. ⬙ I have an airbag ⬙ Airbags offer greater protection when used with safety belts. Frontal airbags are not desi[...]

The driver and front passenger BeltMinder 威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) (automatic transmission) • The gearshift is in N (Neutral) (manual transmission) • The ignition switch is in the [...]

• After receiving confirmation, the deactivation/activation procedure is complete. AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury fr[...]

The National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant’ s chest and the driver airbag module. Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. T o properly position yourself away from the air[...]

Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Airbags can kill or injure a child in a child seat. NEVE[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serio[...]

impact sensors, the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors). Several air bag system components get hot after inflation. Do not touch them after inflation. If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is not replaced, the un[...]

The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is off. The indicator lamp is located in the center stack of the instrument panel just below the radio. Note : The indicator lamp will illuminate for a s[...]

• If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat. Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small child in child safety seat or booster Lit Disabled Small child with safety belt buckled or unbuckled Lit Disabled Adult Unlit Enabled Even with Advance[...]

Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. 3 ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty seat, or small to medium object with safety belt buckled Lit Disabled If you think that the status of the passenger airbag off indicator lamp is incorre[...]

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If ob[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any[...]

How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side air[...]

to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision causes sufficient lateral deceleration. Several airbag system components get hot after inflation. Do not touch them after inflation. If the side airbag has deployed, the airbag will not function again. The side airbag system[...]

Safety Canopy 姟 system (if equipped) Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy 娂 . Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not lean your head on the door . The Safety Canopy 娂 c[...]

How does the Safety Canopy 姟 system work? The design and development of the Safety Canopy 娂 system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment[...]

The Safety Canopy 娂 is mounted to roof side-rail sheet metal, behind the headliner , above the first and second row seats. The Safety Canopy 娂 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events. The fact that the Safety Canopy 娂 did not activat[...]

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently , have the SRS serviced at your authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Disposal of airbags and[...]

If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. Do not leave children, unreliable adults, or pets[...]

• Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating posit[...]

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably cl[...]

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the sa[...]

tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter . Carefully follow all of the manufacturer’ s instructi[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

4. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instruction[...]

Y our vehicle has LA TCH anchors for child seat installation at the following locations: The anchors on both sides of the center of the rear seat are provided primarily for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats. A child seat with rigid LA TCH attachments c[...]

when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor . T ry to tilt the child se[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specification chapter . Y ou should become thoroughly familiar with this information be[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, and di[...]

• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a[...]

At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips.[...]

T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]

cracking, cuts, bruises and other signs of damage or excessive wear . If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety , tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper o[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. If a pressure in excess of the maximum pressure indicated is required, the[...]

• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure[...]

• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Tires, Wheels and Loading 150[...]

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel[...]

3. 65: Indicates the aspect ratio which gives the tire’ s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that rela[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ir[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the [...]

no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System: Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflat[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all-weathe[...]

V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s doo[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2007 E[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driv[...]

transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 — 198 [...]

• Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter . • Service your vehicle more frequently if you tow a trailer . Refer to the severe duty schedule in the scheduled maintenance guide. • Do not tow a t[...]

4x4 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb. (kg) T railer W eight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m) 2 2.3L w/manual transmission 5040 (2286) 1500 (680) 24 (2.2) 2.3L w/automatic transmission 5100 (2313) 1500 (680 ) 24 (2.2) 3.0L w/automatic transmission 7240 (3284 ) 3500 (1588 ) 30 [...]

Safety chains Always connect the trailer’ s safety chains to hook retainers on the vehicle. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper [...]

• T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatic transmission in the Driving chapter . • Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may o[...]

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper . • [...]

STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and steering column and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 3. RUN, all electrical circuits operational and warning lights will illuminate. This is the position the key is in when you?[...]

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. Before starting the vehic[...]

If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3 (RUN) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning[...]

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stop[...]

emphasis on improved performance and environmental considerations can lead to more dust than in the past. Brake dust can be cleaned by weekly washing with soapy water and a soft sponge. Heavier deposits can be removed with Motorcraft Wheel and T ire Cleaner (ZC-37–A). Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-[...]

Parking brake T o set the parking brake (1), pull the parking brake handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. T o release, press and hold the button (2), pull the handle up slightly , then push the handle down. Always set the parking brake fully and make sur[...]

• Do not fill the power steering pump reservoir above the MAX mark on the reservoir , as this may result in leaks from the reservoir . If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tir[...]

If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter . If the fuse is not blown, perform the following procedure: 1. Apply t[...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer as soon as possible. Driving with an automatic overdrive transaxle Y our automatic overdrive transaxle provides fully automatic operation in either D (Overdrive) or with the O/D OFF switch depre[...]

Understanding the gearshift positions of the 4–speed automatic transaxle This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or repair , the transmission will need t[...]

• Move the gearshift lever into the desired gear T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehi[...]

• O/D (Overdrive) is automatically returned each time the key is turned off. 2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to D (Overdrive), move the gearshift lever into the D (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the [...]

MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch V ehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed. When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in the neutral position. 2. Hold down the brake pedal[...]

7. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator pedal. Do not drive with your foot resting on the clutch pedal and do not use the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life. Recommended shift speeds Upshift [...]

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Set the parking brake. 3. Depress the clutch, then shift into 1 (First). 1 24 R 3 5 1 24 R 3 5 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Driving 186[...]

4. T urn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key . Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles nea[...]

Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps. The RSS detects obstacles up to 6 feet (1.8 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approxi[...]

If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this cha[...]

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow , mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles T ruck and utility vehicles can differ from some othe[...]

• It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over . Remember , your safety and the safety of others should be your primary concern. V ehicles with a highe[...]

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more. Additionally , smooth variations of [...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et[...]

slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer . When climbing a ste[...]

A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. A void sudden braking as well. Although a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster , because as in other vehicles, braking o[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty perio[...]

• exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartm[...]

flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantia[...]

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet[...]

Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses. 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 201[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* T railer tow park lamps 2 — Not used 3 15A* Front and rear park lamps 4 10A* Ignition switch 5 2A* Powertrain Control Module (PCM relay), Fuel pump relay , Main fan relay , High/Low speed fan relay 2, P A TS module 6 15A* Center[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 22 10A* Instrument cluster 23 — Not used 24 20A* Cigar lighter 25 20A* Front wiper motor , Front wiper washer 26 5A* Climate control system mode switch 27 5A* Speed control cancel switch 28 10A* Instrument cluster 29 10A* Reverse park aid 30 — Not used 31 — Not u[...]

Always disconnect the battery before servicing high current fuses. T o reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 12 20A* Power point 13 20A* Fog lamps 14 15A* A/C clutch, A/C relay 15 30A* Anti-lock Brake System (ABS) solenoid 16 25A* I/P fuse panel (RUN/ST ART) 17 50A** Ignition (main) 18 40A** Blower motor 19 40A** Accessory delay relay - Subwoofer and 4WD, Low beam 20 60A** ABS 21 40A**[...]

CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle’ s speed. • hold the steering wheel firmly . • slowly move to a safe place on the side of the road. Y our vehicle may be equipped with a conventional spare tire that is different in one or more of the following: type, brand[...]

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • T ow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • [...]

• W inter weather driving capability • W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • T owing a trailer • Driving vehicles equipped with a camper body • Driving[...]

If the vehicle slips off the jack, you or someone else could be seriously injured. 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine off. 3. Block the diagonally opposite wheel. Removing the jack and tools[...]

Unbuckle the strap and remove the jack and tools by pulling the right side up first. Remove the tools from the jack in order to remove the spare tire from under the vehicle. Note: For some non-cargo management system vehicles, the jack and tools are located in the right rear of the cargo area behind an access panel. Cargo management system (if equi[...]

T o remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first. Remove the lug wrench from the jack in order to remove the spare tire from under the vehic[...]

If equipped with a tether , perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether . 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached V elcro [...]

Changing the flat tire 8. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 213[...]

• Rear 9. Lower the jack from its stored height to fit under the jacking notches. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Never use the differentials as a jacking point. T o lessen the risk of personal injury , do not put any part of your [...]

11. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 12. Lower the wheel by turning the jack handle counterclockwise. 13. Remove the jack and fully tighten the lug nuts in the order [...]

• guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive. Non-cargo management system (if equipped): • Reclip the tools onto the jack making sure that th[...]

1. Place tire on end with valve stem facing rearward, away from vehicle. 2. Place tether into bolt holes in wheel and attach lug nut using lug wrench. 3. Lay the tire on the ground with the valve stem facing down. If your vehicle is equipped with aluminum wheels, remove the wheel ornament. 4. Slide the wheel partially under the vehicle and install [...]

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Ford r[...]

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’ s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine c[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2007 Escape (204) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 220[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the bat[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not a[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the fol[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle Arbitration Plan (CAMV AP). The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disag[...]

GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than[...]

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www .helminc.com. (Items in this catalog may be purchased by credit card, check or money order .) Obtaining a French owner ’ s guide French Owner’ s Guides can be obtained from[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

• W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpe[...]

• T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressur[...]

• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3–A). • If tar or grease spots[...]

Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’ s heated grid lines. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, dry cloth, or use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). ?[...]

Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaning the seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect performance of the side airbag in a collision. LEATH[...]

Motorcraft Car W ash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail W ash (ZC-3–A) Moto[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Owner Information Guide to find out which parts and services [...]

2. Block the wheels. T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift u[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil filler cap 9. Engine oil dipstick 10. W indshield washer fluid reserv[...]

3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. W indshield washer fluid reservoir 2007 Escape (204) Owners Guide (post-2002-fmt) [...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smea[...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. Push the lock tab (A) to release the blade from the arm loop and pull the blade down toward the windshield to remove it from the arm. 2. Attach the new blade to the arm loop and pull it into place until a click is heard. Repla[...]

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark or the lower hole, engine oil must be added to [...]

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above the MAX mark or upper hole may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7[...]

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil l[...]

Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises o[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about [...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, meeting Ford specificati[...]

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir . If you removed the[...]

Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The indicator light will illuminate. • HIGH ENGINE TEMPERA TURE will be displayed in the message center . If the engine reaches a preset over -temperature condition, the engine will automatically switch to al[...]

Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to an authorized dealer as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. Remove fuel filler cap slowly . Otherwise, fuel m[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator , refer to W arning lights and chimes in th[...]

• Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling met[...]

• Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy . •[...]

• Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Close windows for high speed driving. EP A window sticker Every new vehicle should have the EP A window sticker . Contac[...]

Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly . Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any [...]

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If the indicator is on, refer to the description in the W arning lights and chimes section of the Instrument Cluster chapter . Y our vehicle may not pass the I/M test with the indicator on. If [...]

4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir . BRAKE/CLUTCH FLUID Brake[...]

during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. W ith the parking brake engaged and your foot on the b[...]

High fluid level Fluid levels above the crosshatch zone may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the corr[...]

Checking and adding manual transmission fluid (if equipped) 1. Park the vehicle on a level surface. 2. Engage the parking brake fully – put in first gear . 3. Assure the vehicle cannot move. 4. Clean the filler plug. 5. Remove the filler plug and inspect the fluid level. 6. Fluid level should be at bottom of the opening. 7. Add enough fluid throu[...]

3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the air filter housing. 5. W ipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing an[...]

MOTORCRAFT PART NUMBERS Component 2.3L I4 engine 3.0L DOHC V6 Duratec engine Air filter element 1 F A-1683 F A-1683 Fuel filter FG-800-A FG-800-A Battery BXT -40R BXT -40R Oil filter FL-910 FL-820-S PCV valve 2 Spark Plugs 3 1 Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name or equivalent Ford part number / Ford Specification Brake fluid and (clutch fluid if equipped) Fill to line on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A Door weatherstrips — Silicone Lubricant XL-6 / ESR-M13P4-A Body hi[...]

Item Capacity Ford part name or equivalent Ford part number / Ford Specification Lock cylinders — Motorcraft Penetrating and Lock Lubricant XL-1 / None Power steering fluid Fill to line on reservoir Motorcraft MERCON 威 AT F XT -2-QDX / MERCON 威 Power T ransfer Unit fluid (4X4-Manual T ransaxle) 12 ounces (0.35L) Motorcraft SAE 80W -90 Premium[...]

1 Add the coolant type originally equipped in your vehicle. 2 Use of synthetic or synthetic blend motor oil is not mandatory . Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark. 3 The Power T ransfer Unit is lubricated for life with synthetic lube. Lubricant levels are not to be checked or [...]

ENGINE DATA Engine 2.3L I4 engine 3.0L DOHC V6 Duratec engine Cubic inches 140 183 Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system Coil on plug Coil on plug Spark plug gap 0.049–0.053 inch (1.25–1.35mm) 0.052–0.056 inch (1.32–1.42mm) Compression ratio 9.7:1 10.0:1 Engine drivebelt routing • 2.3L I4 Engin[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNA[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Lifestyle Ash cup/ smoker’ s package Cargo organization and management Cross bars T railer hitches, wiring harnesses and accessories Peace of mind Mobile-ease 娂 hands-free communication system Remote start V ehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equ[...]

A Accessory delay .......................... 58 Air cleaner filter ...............271, 273 Airbag supplemental restraint system ........112, 121, 124 and child safety seats ............ 114 description .............. 112, 121, 124 disposal .................................... 127 driver airbag ............114, 122, 125 indicator light .........120,[...]

Cleaning your vehicle engine compartment .............. 234 instrument panel .................... 237 interior ..................................... 237 interior trim ............................ 237 plastic parts ............................ 236 washing .................................... 233 waxing ..................................... 233 wheel[...]

checking and adding .............. 245 dipstick .................................... 245 filter , specifications ........ 248, 273 recommendations ................... 248 refill capacities ........................ 274 specifications .......................... 274 Exhaust fumes .......................... 175 F Fail safe cooling .....................[...]

autolock ..................................... 76 keypad ....................................... 83 locking and unlocking doors .... 84 programming entry code ......... 83 Keys ............................................. 85 positions of the ignition ......... 172 L Lamps autolamp system ....................... 42 bulb replacement specifications c[...]

fluid, specifications ................. 274 Power W indows ........................... 57 Preparing to drive your vehicle ........................................ 178 R Radio ................................19, 28, 32 Rear window defroster ...............41 Relays ........................................ 199 Remote entry system ................. 78[...]

alignment ................................ 149 care .......................................... 145 changing .................................. 208 checking the pressure ............ 145 inflating ................................... 143 label ......................................... 155 replacing .................................. 147 rotating ....[...]

288[...]