Ford 2007 Focus manuel d'utilisation

Introduction 4 Instrument Cluster 10 W arning lights and chimes 10 Gauges 14 Entertainment Systems 16 AM/FM stereo with single CD 16 AM/FM stereo with in-dash six CD 20 Climate Controls 25 Heater only 25 Manual heating and air conditioning 26 Rear window defroster 28 Lights 29 Headlamps 29 T urn signal control 32 Bulb replacement 32 Driver Controls[...]

Seating and Safety Restraints 62 Seating 62 Safety restraints 67 Airbags 81 Child restraints 92 Tires, Wheels and Loading 105 T ire information 105 T ire inflation 107 V ehicle loading 120 T railer towing 125 Recreational towing 127 Driving 129 Starting 129 Brakes 132 T raction Control™ 134 T ransmission operation 136 Roadside Emergencies 142 Get[...]

Maintenance and Specifications 178 Engine compartment 180 Engine oil 182 Battery 184 Engine coolant 186 Fuel information 192 Air filter(s) 206 Part numbers 207 Maintenance product specifications and capacities 208 Engine data 210 Accessories 213 Index 215 All rights reserved. Reproduction by any means, electronic or mechanical including photocopyin[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . Front seat mounted rear -facing child or inf[...]

Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfuncti[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your ve[...]

that the vehicle is not ready for I/M testing. See the Readiness for Inspection/Maintenance (I/M) testing in the Maintenance and Specifications chapter . Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to OBD-II in the Maintenance and Specifications chapter . If the[...]

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated. Airbag readiness: If this light fails to illuminate when ignition is turned to ON, [...]

Upshift (if equipped): To maximize fuel economy , this light illuminates when the manual transmission should be shifted to the next highest gear . Refer to the Driving chapter for more information. T raction Control 娂 system (if equipped): Illuminates when the T raction Control 娂 is turned OFF and will flash when active. If the light remains on[...]

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’ s door is opened. Gearshift warning chime (automatic transaxle only): Sounds when the gearshift lever is not in P (Park) and the driver’ s door is opened. GAUGES Speedometer: Indicates the current v[...]

Odometer: Registers the total miles (kilometers) of the vehicle. T rip odometer: Registers the miles (kilometers) of individual journeys. T o reset, depress the reset control. T achometer (if equipped): Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engi[...]

AUDIO SYSTEMS AM/FM stereo with single CD — Premium (if equipped) AM/FM stereo with single CD/MP3 — Premium (if equipped) 2007 Focus (foc) Owners Guide (post-2002-fmt) USA (fus) Entertainment Systems 16[...]

1. / T une selector: Press to manually increase/decrease the radio frequency . 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press MENU to access the main menu functions. Use the T une selector ( / )o r SEEK for adjustments. T rack/Folder mode: (A vailable with the CD/MP3 Premium system only). [...]

selector ( / )o r SEEK to turn off or select rates 1 through 7. Rate 7 compensates the most volume at higher speeds. Setting the clock: Upon initial battery connect, this function is displayed first among MENU functions. Once the clock is set, this will be shown as the last MENU function. Press MENU until SELECT HOUR or SELECT MINS is displayed. Pr[...]

11. Rewind: Press and hold to manually reverse the CD. 12. Memory presets: T o set a station: Select frequency band AM/FM1/FM2; tune to a desired station, press and hold the preset button until the display shows that the preset is set. 13. Scan: Press for a brief sampling of all strong radio stations or CD tracks. Press again to stop scan function.[...]

AM/FM Stereo with In–dash 6CD —Premium /Audiophile (if equipped) 1. / T une Selector: Press to manually increase/decrease the radio frequency when in tuner mode or to choose a different disc when in CD mode with multiple discs in the changer . 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: P[...]

T o activate RDS, press and hold MENU until RDS ON or RDS OFF appears in the display . Press MENU again to continue to FIND and SHOW functions. Press the T une Selector ( / )o r SEEK to toggle RDS on/off and to scroll through the FIND and SHOW functions. T rack/Folder mode: A vailable only on MP3 discs in CD mode. In T rack Mode, CD functions use a[...]

5. Seek up: Press for next strong station or CD track. Press and hold for continuous seek functionality . 6. T ext: Press in CD mode to display track title, artist and album title. This feature will only function if the CDs are manufactured with the CD text feature. 7. Shuffle: Press to play tracks in random order on the selected CD. The first pres[...]

16. ON/OFF/V olume: Press to turn ON/OFF; turn to increase/decrease the volume levels. If the volume is set above a certain level and the ignition is turned off, for at least a minute, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 17. CD: Press to enter CD mode. If a CD is already loaded[...]

• Station overload: When you pass a broadcast tower , a stronger signal may overtake a weaker one and play while the weak station frequency is displayed. CD/CD player care Do: • Handle discs by their edges only . Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center ou[...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in the cabin. See the following for a brief description on each control. : Distributes air through the instrument panel vents. : Distributes air through the instrument panel vents and the floor vents. : Distributes air through the floor vents. : Distribut[...]

2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these [...]

5. A/C: Provides cabin cooling. 6. T emperature selection: Controls the temperature of the airflow in the cabin. Max A/C: For maximum cabin cooling performance, select A/C (5) and (4). Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position and turn the fan on. • T o reduce h[...]

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Ambient lighting (if equipped) Illuminates 4 footwells and 3 cupholders with a choice of 7 colors. The ambient lighting control switch is located on the center console by the gearshift lever . T o [...]

High beams Pull the lever towards you to activate. Pull the lever towards you again to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp contr[...]

V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and m[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome lamps The dome lamp is equipped with a control switch that will illuminate when: • the doors are closed and the switch is in the on position. • the switch is in the door activated position and any door is open. [...]

Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America to ensure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bul[...]

Replacing headlamp bulbs 1. Make sure the headlamp control is in the OFF position and open the hood. 2. Pull off the bulb cap. 3. Disconnect electrical connector from the bulb. 4. T wist off the bulb retainer ring by turning it counterclockwise. 5. Pull the bulb straight out. Install in reverse order . Handle a halogen headlamp bulb carefully and k[...]

Replacing tail/brake/backup lights and turn signal bulbs (3dr & 5dr) 1. Make sure the headlamp control is in the OFF position and then open the hatchback. 2. From inside the luggage compartment remove a wing nut (if equipped) from the lamp assembly . 3. Using a Phillips screwdriver remove the screw . The lamp is still retained by a spring loade[...]

Replacing tail/brake/backup lights and turn signal bulbs (wagon) 1. Make sure the headlamp control is in the OFF position and then open the hatchback. 2. Using a screwdriver , remove two screws and gently pull the lamp assembly away from the vehicle. 3. Remove the socket from the lamp assembly 4. Pull the bulb straight out of the socket. Install in[...]

Replacing high-mount brake lamp bulbs Sedan 1. Make sure the headlamp control is in the OFF position and open the luggage compartment. 2. Pull the bulb holder from the lamp assembly . 3. Pull the bulb straight out. Install in reverse order . 3dr & 5dr and wagon 1. Make sure the headlamp control is in the OFF position. 2. Remove the screws using[...]

Replacing the luggage compartment lamp 1. Make sure the headlamp control is in the OFF position. 2. Carefully pry out the light assembly from the holder with a flathead screwdriver . 3. Pull the bulb straight out. Install in reverse order . Replacing interior lamps 1. Make sure the headlamp switch is in the OFF position. 2. Switch off the interior [...]

MUL TI-FUNCTION LEVER W indshield wiper: Move the lever down for a single wipe. For intermittent operation, move control up one position and adjust the rotary control to the desired speed. For normal operation, move control up two positions. For high speed operation, move control up three positions. Mist function: T o mist, push and release the win[...]

TILT AND TELESCOPE STEERING COLUMN (IF EQUIPPED) Pull the locking lever down to adjust and telescope the steering column position. Return the lever to its original position to secure the wheel. The telescope function is adjusted by moving the wheel toward the driver to telescope out and toward the instrument panel to telescope in. Always place both[...]

• Place the VELCRO 威 hook onto the side of the aftermarket transmitter opposite of the button. • Place the transmitter into storage compartment, button down. • Place the provided height adaptors onto the back of the door as needed. • Close the door . • Press the depression in the door to activate the transmitter . AUXILIARY POWER POINT [...]

Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage no[...]

EXTERIOR MIRRORS Power side view mirrors (if equipped) T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. Heated mirrors (i[...]

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET ACCEL control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on[...]

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL cont[...]

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control. Turning of f speed control Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Remote audio steering column controls (if[...]

Move the SEEK control towards the instrument panel to seek to the next radio station down the frequency band or the previous CD track. • MODE: Press and hold to toggle through AM/FM1/FM2/CD modes. Press and release to move to the next preset radio station, or the next CD. Press in all modes to abort a traffic message during broadcasting. MOON ROO[...]

T o vent: • T o tilt the moon roof into the vent position (when the glass panel is closed), press and hold the front portion of the control. • T o close the moon roof from the vent position, press and hold the rear portion of the control until the glass panel stops moving. Before operating the moonroof you should verify that it is free of obstr[...]

POSITIVE RETENTION FLOOR MA T Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operat[...]

T o reduce the risk of injury , the luggage cover must be properly attached to the mounting clips. Do not place any objects on the cargo area cover . They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. The cover may cause injury in a sudden stop or accident if it is not securely installed. LIF[...]

LUGGAGE RACK (IF EQUIPPED) The maximum recommended load is 220 lbs (100 kg) on the luggage rack structure. The load must be placed directly on the dealer installed cross-bars (if equipped) and luggage rack. The vehicle’ s roof panel is not designed to carry a load. When loading the luggage rack, it is recommended to evenly distribute the load, as[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Y our keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized deal[...]

1. T urn the ignition to the 3 (ON) position. 2. Press the power door unlock control three times. 3. T urn the ignition from 3 (ON) position to the 2 (OFF) position. 4. Press the power door unlock control three times. 5. T urn the ignition back to 3 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The ho[...]

INTERIOR LUGGAGE COMPARTMENT RELEASE Y our vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle. T o o[...]

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Chan[...]

2. W ith the all-door remote entry , press and release again within three seconds to unlock all the doors. The remote entry system activates the illuminated entry feature. This feature turns on the interior lamps for 25 seconds or until the ignition is turned to the 3 (ON) position. The dome lamp control must be set to the ON position in order for [...]

Note: The panic alarm will only operate when the ignition is in the 1 (LOCK) or 2 (OFF) position. Opening the luggage compartment Press once to open the luggage compartment. Note: This feature will only operate with the ignition in the 1 (LOCK) or the 2 (OFF) position. • Ensure that the trunk is closed and latched before driving your vehicle. Fai[...]

5. Snap the two halves back together . Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lo[...]

started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Y our vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer . The authorized dealer can program your spare keys to your vehicle or you can program the keys your[...]

Programming spare keys Y ou can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. T ips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • Y ou must have two previously programmed coded keys (keys that already operate your vehicle’ s engine)[...]

11. Y our new , unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’ s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’ s engine and the theft indicator light will flash on and [...]

SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo [...]

Adjusting the front manual seat Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor . T o reduce the risk of p[...]

Lift the control to adjust the angle of the seatback. Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Heated seats (if equipped) The heated seats switch is located on the center console. T o operate the heated seats: • Push control to activat[...]

Tip/slide front seat (3–door) Lift the control and fold the seatback forward. The seat can be slid forward to allow easier entry to the rear seats. Slide the seat back and fold back the seatback until it locks with a distinct click. The seatback will return to its original position. Rock the seat to ensure that the catch is securely engaged. On t[...]

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Folding the rear seat bac[...]

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Note that the center rear[...]

Y our vehicle’ s Personal Safety System 娂 consists of: • Driver and passenger dual-stage airbag supplemental restraints. • Front safety belts with pretensioners, energy management retractors, and safety belt usage sensors. • Driver’ s seat position sensor . • Front crash severity sensor . • Front passenger sensing system • “Pass[...]

information early in the crash event on the severity of the impact. This allows your Personal Safety System 娂 to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver ’s seat position sensor The driver’ s seat position sensor allows your Person[...]

will light and stay lit to remind you that the front passenger frontal airbag is off. See Front passenger sensing system in the airbags section of this chapter . Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Pe[...]

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and warning light are repaired. If any of these things happen, even intermittently , have the Personal Safety System 娂 serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collisio[...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened[...]

response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply , or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode When to use the automatic locking mode In this mod[...]

How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify that the ⬙ automatic locking retractor ⬙ feature for child seats is still working properly . Safety belt assemblies should be inspect[...]

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Safety belt pretensioner Y our vehicle is equipped with safety belt pretensioners at the driver and front out[...]

a collision be replaced. However , if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly , they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Failure to insp[...]

therefore potentially in need of a warning. T o avoid activating the BeltMinder 威 feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the front passenger sensing system. Both the driver’ s and passenger’ s safety belt usages are monitored and either may activate th[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during our[...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

• The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled While the design allows you to deactivate your BeltMinder 威 ,t h i s system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the BeltMinder 威 system activated for yourself and [...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly or gently , and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag m[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The National Highway T raffic Safety Administration (NHTSA)[...]

Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Airbags can kill or injure a child in a child seat. NEVE[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

• Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter . • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system. later in this chapter . • a readiness light and tone. • diagnostic module. • and the electrical wiring which connects the componen[...]

For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passeng[...]

• Have the person sit upright in the seat, centered on the seat cushion, with the person’ s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit eve[...]

Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. 3 ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty seat, or small to medium object with safety belt buckled Lit Disabled If you think that the status of the passenger airbag off indicator lamp is incorre[...]

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If ob[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until[...]

How does the side airbag system work? The side airbag system consists of the following: • An inflatable nylon bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnost[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase the risk of injury in[...]

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather , they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children (genera[...]

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , which could increase the risk of serious injury in a crash. T o improve the [...]

T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’ s head (top of ear level) [...]

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably cl[...]

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the sa[...]

tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter . Carefully follow all of the manufacturer’ s instructi[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buc[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

• On Sedan’ s the anchors are located on the rear back panel. • For 3–door/5–door and W agon, the anchors are located on the back of the rear seat. 4. On a sedan, open the tether anchor cover . 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly i[...]

7. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. If the safety seat is not anchored properly , the risk of a child being injured in a collision greatly increases. Attaching child safety seats with Lower Anchor and T ethers for Children (LA TCH) attachments for child seat anchors Some child safety seats[...]

The LA TCH anchors are located on the rear section of the seat cushion, at the bottom of the seatback. Follow the child seat manufacturer’ s instructions to properly install safety seats with LA TCH attachments. Attach the LA TCH lower attachments of the child seat only to the appropriate locations shown. Once you have installed the LA TCH safety[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are [...]

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate [...]

Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an [...]

Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may res[...]

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve [...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]

Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect[...]

• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equip[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The original equipment tires on your vehicle have an all-weather tread design to provide traction, handling, and braking performance in year -round driving. Y ou may install snow tires for improved traction when driving in areas with su[...]

Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating[...]

GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The GVW must never exceed the GVWR. Exceeding the Safety Complianc[...]

10–15% (conventional trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and T railer T owing Guide provided by your authorized dealer) for more detailed information. Do not exceed the GVWR or the GA WR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower load carrying [...]

capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 - (5 x 220) - (5 x 30) = 1400 - 1100 - 150 = 150 lb. Y es, you have enough load capacity in your vehicle to transport four friends and your gol[...]

T RAILER TOWING Refer to the following chart to determine how much weight your vehicle can tow: Model Passengers/Luggage load - lb. (kg) Maximum trailer weight - lb. (kg) 3–door 5/827 (375) 630 (286) 4/677 (307) 780 (354) 3/527 (239) 930 (422) 2/377 (171) 1080 (490) 1/227 (103) 1230 (558) 4–door and 5–door 5/827 (375) 585 (265) 4/677 (307) 73[...]

Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10?[...]

• Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transaxle cooling. • Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transaxle damage may occur . Servicing after towing If you tow a trailer for long distances[...]

In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle can be flat towed (all wheels on the ground) under the following conditions: • Place the transmission in N (Neutral). • Maximum speed is 35 mph (56 km/h). • Maximum distance is 50 miles (80 k[...]

STARTING Positions of the ignition 1. LOCK, locks the steering wheel, automatic transaxle gearshift lever and allows key removal. 2. OFF , shuts the engine and all electrical accessories off without locking the steering wheel. 3. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 4. ST ART , cranks the [...]

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. Before starting the vehic[...]

If starting a vehicle with a manual transaxle: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor . • T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning ligh[...]

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring [...]

Four-wheel anti-lock brake system (ABS) (if equipped) Y our vehicle may be equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking; any pulsation or mechanical[...]

The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. T o release, press and hold the button (2), pull the handle up slightly , then push the handle down. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (man[...]

The T raction Control 娂 switch is located on the center console, by the gearshift lever . The T raction Control 娂 system will automatically turn on every time the ignition is turned off and on. If you should become stuck in snow or ice or on a very slippery road surface, try switching the T raction Control 娂 system off by pressing the switch.[...]

• loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P[...]

Do not drive your vehicle until you verify that the brakelamps are working. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the bra[...]

T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn th[...]

2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to D (Overdrive), move the gearshift lever into the D (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transaxle to downshift to second gear at the appropriate vehicle speed. 1 (Firs[...]

T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral position. 3. Start the engine. 4. Press the brake pedal and move the gearshift lever to the desired gear; 1 (First) or R (Reverse). 5. Release the parking brake, then slowly release the clutch peda[...]

• The gearshift lever can only be moved into R (Reverse) by moving it from left of 3 (Third) and 4 (Fourth) before shifting into R (Reverse). This is a lockout feature that protects the transmission from accidentally being shifted into R (Reverse) from 5 (Fifth). If R (Reverse) is not fully engaged, press the clutch pedal down and return the gear[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty perio[...]

• exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartm[...]

to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engin[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description R17 — Starter relay R18 — Not used R19 — Not used R20 — Not used R21 — Daytime running lamps R22 — Not used R23 — Not used R24 — Not used R25 — Rear defrost/Heated mirror relay 30 10A Parking lamps 31 20A Radio 32 15A T[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 33 20A Sunroof 34 20A Horn 35 7.5A A/C switch, Instrument cluster 36 7.5A Interior lamps, Power mirrors 37 — Not used 38 — Not used 39 2A PCM relay coil 40 25A Rear defroster 41 — Not used 42 10A Stop lamps, Shift interlock 43 15A Rear wiper , Sunroof (ignition) [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 61 7.5A P A TS modules, Instrument cluster 62 7.5A Radio (Start) 63 20A Power locks (GEM) Note: Fuse 63 is located on the back of the fuse panel. See your authorized dealer for service of this fuse. Power distribution box The power distribution box is located in the en[...]

T o remove a fuse, use the fuse puller tool provided on the power distribution box cover . The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 40A Main power supply (to passenger compartment fuse panel) 2 — Not used 3 — Not used 4 30A Air pump motor (PZEV engine only) 5 30A Anti-[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 10 1A Battery voltage sense 11 30A Subwoofer 12 15A Fuel pump motor 13 20A Anti-lock Brake System (ABS) (valves) 14 — Not used 15 — Not used 16 10A Low beam (left-hand side) 17 10A Low beam (right-hand side) 18 15A Heated Exhaust Gas Oxygen (HEGO) sensors 19 40A Heater blowe[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description R10 — Cooling fan relay R11 — Not used R12 — Not used R13 — Not used R14 — Not used R15 — Air pump motor relay R16 — Not used D1 — Not used D2 — Not used D3 — A/C clutch diode D4 — Not used CHANGING A FLAT TIRE If you get a flat tire while driving: • do n[...]

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T -type mini-spare: This spare tire begins with the letter “T” for tire size and may have “T emporary Use Only” molded in the sidewall 2. Full-size dissimilar s[...]

• Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather drivi[...]

T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. If the vehicle slips off the jack, you or someone else could be seriously injured. 2. Place gearshift lever in P (Park[...]

5. If equipped with a 6–spoke wheel cover that’ s bolted on, remove the four plastic nuts by turning counterclockwise 1/4 turn for access to the lug nuts. Note: T o avoid damage to the wheel cover , the 6–spoke wheel cover cannot be removed until the tire is off the vehicle. 6. Loosen each wheel lug nut one-half turn counterclockwise but do n[...]

11. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 12. Put flat tire, jack and lug wrench away . Make sure the jack is fastened so it does not rattle when you drive. Unblock the wheels. WHEEL LUG NUT TORQUE SPECIFICATI[...]

Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability . Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Preparing your vehicle When the battery i[...]

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + ?[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]

3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to d[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator NHTSA 400 Seventh Street, SW W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING SAFETY [...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

W AXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product. • Do[...]

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine bl[...]

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellant coatings, tree sap, or other organic con[...]

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted sur[...]

LEATHER SEATS (IF EQUIPPED) Y our leather seating surfaces have a clear , protective coating over the leather . • T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11–A). Dry the area with a soft cloth. • T o help maintain its resiliency and color , use the Motorcraft Deluxe Leather Care Kit (ZC-11–D), availab[...]

Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft One Step W ash and W ax Concentrate (ZC-6-A) Motorcraft Paint Sealant (ZC-45) Motorcraft Premium Car W ash Concentrate (U.S. only) (ZC-17-B) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Liquid W ax[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Owner Information Guide to find out which parts and services[...]

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L/2.3L I4 Engines 1. W indshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Battery 7. Automatic transaxle fluid dipstick (if equipped) 8. Engine oil dipstick 9. Power steering fluid reservoir 2007 Focus [...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

Poor wiper quality can be improved by cleaning the wiper blades and the windshield, refer to Windows and wiper blades in the Cleaning chapter . T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge o[...]

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil l[...]

Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises o[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about [...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, meeting Ford specificati[...]

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir . If you removed the[...]

Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The “Check Engine” indicator light will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder[...]

FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not u[...]

• Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . If fuel is swallowed, call a physician immediately , even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • A void inhaling fuel vapors. Inhaling t[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally , adding one gallon of fuel is enough to restart the engine. If the vehicle is [...]

• Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same[...]

• Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h[...]

• Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransaxles give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Close windows [...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate tha[...]

3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter . 4. Driving through deep water – the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving [...]

vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30 second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine.[...]

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir . The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of[...]

6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 50°F (10°C)[...]

If necessary , add fluid in 1/2 pint (250 mL) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additiv[...]

MOTORCRAFT PART NUMBERS Component 2.0L I4 engine 2.3L I4 engine Air filter element N/A (Lifetime) 1 N/A (Lifetime) 1 Fuel filter FG-1081 FG-1081 Oil filter FL-910 4 FL-910 4 Battery BXT -96R BXT -96R Battery (if equipped with Audiophile radio or engine block heater) BXT -40R BXT -40R PCV valve 2 Spark plugs 3 1 Non Serviceable Part. The air filter [...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Brake fluid and clutch fluid (if equipped) Fill to line on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1 or PM-1-C / ESA-M6C25-A or WSS-M6C62-A Door latch, hood latch, auxiliary hood latch,[...]

Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Cooling system stop leak pellets — Motorcraft Cooling System Stop Leak Pellets VC-6 / WSS-M99B37-B6 Power steering fluid Fill to between MIN and MAX lines on reservoir Motorcraft MERCON 威 AT F XT -2-QDX / MERCON 威 W indshield washer fluid 5.1 quarts (4.8L) Motorc[...]

ENGINE DATA Engine 2.0L I4 engine 2.3L I4 engine Cubic inches 121 138 Required fuel 87 octane 87 octane Firing order 1–3–4–2 1–3–4–2 Ignition system C.O.P C.O.P Compression ratio 10.1:1 9.7:1 Spark plug gap .051 inch +/- .002 1.3 mm +/- .05 .051 inch +/- .002 1.3 mm +/- .05 Engine drivebelt routing • 2.0L / 2.3L I4 Engine without A/C [...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNA[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Lifestyle Ash cup / smoker’ s package Cargo organization and management T ripT unes 娂 Peace of mind Mobile-Ease 娂 hands free communication system Remote start V ehicle security systems Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following information in mind when adding accessories o[...]

A Air cleaner filter ............... 206–207 Airbag supplemental restraint system ....................81, 90 and child safety seats .............. 83 description ..........................81, 90 disposal ...................................... 92 driver airbag ........................83, 91 indicator light ...........................89 operation .[...]

Climate control (see Air conditioning or Heating) ...... 25–26 Clutch fluid .......................................... 204 operation while driving .......... 139 recommended shift speeds .... 140 Console overhead .................................... 40 Controls steering column ........................46 Coolant checking and adding .............. [...]

calculating fuel economy .......197 cap ........................................... 194 capacity ................................... 208 choosing the right fuel ........... 195 comparisons with EP A fuel economy estimates .................200 detergent in fuel ..................... 196 filling your vehicle with fuel .................. 192, 194, 197[...]

Lane change indicator (see T urn signal) ........................32 Liftgate ........................................ 50 Lights, warning and indicator .... 10 anti-lock brakes (ABS) ..........133 Load limits ................................. 120 Locks autolock ..................................... 52 childproof .................................. 53[...]

Occupant Classification Sensor ........................................ 69 safety belt maintenance ........... 75 warning light and chime .......... 76 Safety seats for children ............ 97 Safety Compliance Certification Label ....................211 Seat belts (see Safety restraints) ...............67 Seats ...................................[...]

W asher fluid .............................. 181 W ater , Driving through ............. 141 W indows power ......................................... 42 rear wiper/washer ..................... 39 W indshield washer fluid and wipers checking and adding fluid .....181 operation ................................... 39 replacing wiper blades ........... [...]

221[...]

222[...]

223[...]

224[...]