Ford 2010 F-250 manuel d'utilisation

Introduction 4 Instrument Cluster 14 W arning lights and chimes 14 Gauges 21 Message center 25 Entertainment Systems 43 AM/FM stereo 43 AM/FM stereo with CD 45 AM/FM stereo with in-dash six CD 52 Auxiliary input jack 59 USB port 61 Satellite radio information 65 Family entertainment system 68 Navigation system 97 SYNC 威 97 Climate Controls 98 Hea[...]

Locks and Security 148 Keys 148 Locks 148 Anti-theft system 159 Seating and Safety Restraints 163 Seating 163 Safety restraints 172 Airbags 184 Child restraints 194 Tires, Wheels and Loading 215 T ire information 218 T ire inflation 220 T ire Pressure Monitoring System (TPMS) 236 V ehicle loading 243 T railer towing 251 T railer brake controller -i[...]

Customer Assistance 337 Reporting safety defects (U.S. only) 343 Reporting safety defects (Canada only) 343 Cleaning 344 Maintenance and Specifications 354 Engine compartment 356 Engine oil 359 Battery 362 Engine coolant 364 Fuel information 370 Air filter(s) 388 Part numbers 389 Maintenance product specifications and capacities 390 Engine data 394[...]

CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following [...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’[...]

Using your vehicle with a snowplow For more information and guidelines for using your vehicle with a snowplow , refer to the Driving chapter . Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommenda[...]

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly d[...]

T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful[...]

V ehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’ s W arranty Guide for more information. Some vehicles are equipped with Powertrain Control Systems that can detect[...]

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’ s Guide. A market unique supplement may be supplied that complements this book. By referring to the mar[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES Automatic transmission cluster shown, manual similar Harley-Davidson vehicles W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate [...]

bulbs work. If any light remains on after starting the vehicle, refer to the respective system warning light description for additional information. Note: Some warning lights are reconfigurable telltale (RTT) indicator lights and will illuminate in the message center . These lights function the same as the other warning lights. Service engine soon:[...]

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the on position when the engine is not running, or in a position between on and start, or by applying the parking brake when the ignition is turned to the on position. If the brake system warning light d[...]

Engine oil pressure: Illuminates when the oil pressure falls below the normal range. Refer to Engine oil in the Maintenance and Specifications chapter . Low tire pressure warning (if equipped): Illuminates when your tire pressure is low . If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating y[...]

Check fuel cap (R TT): Displays when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter . Engine coolant temperature (R TT): Displays when the engine coolant temperature is high. Stop the v[...]

Four wheel drive low (if equipped): Illuminates when four -wheel drive low is engaged. Four wheel drive high (if equipped): Illuminates when four -wheel drive high is engaged. Anti-theft system: Flashes when the SecuriLock 威 Passive Anti-theft System has been activated. Speed control (if equipped): Illuminates when the speed control is activated.[...]

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’ s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’ s door is opened. Parking brake on warning chime: Sounds[...]

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrument cluster Instrument Cluster 21 2010 F-250/350/450/550 (f23) Owners Guide, 1st Printing USA (fus)[...]

Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. W ARNING: Never remove the[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Standard instrument cluster Harley-Davidson instrument cluster Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “[...]

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Specificatio[...]

Altering the severity of the operating conditions is recommended to lower the transmission temperature into the normal range. Red area– the transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range. If the gauge is operating in the Y ellow or Red area, stop the vehicle and verify the airflow is not res[...]

DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display . The running average fuel economy is re-initialized to a factory default value if the battery is disconnected. XX.X MPG (L/100km) A verage fuel economy displays[...]

T o reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or 12 months) perform the following: 1. Press and release the setup button to display “OIL LIFE XXX% HOLD RESET = NEW”. 2. Press and hold the SELECT/RESET stem for two seconds and release to reset the oil life to 100%. Note: T o change oil l[...]

HOLD RESET FOR SYSTEM CHECK Press and hold the SELECT/RESET button to select SYSTEM CHECK when HOLD RESET FOR SYSTEM CHECK is displayed in the message center . For each of the monitored systems, the message center will indicate either an OK message or a warning message for two seconds. Pressing the SELECT/RESET button cycles the message center thro[...]

• Some messages will reappear after clearing or being reset if a problem or condition is still present and needs your attention. • Some messages can be acknowledged and reset by pressing the SELECT/RESET button. This allows you to use the full message center functionality by clearing the message. P ARK BRAKE ENGAGED — Displayed when the parki[...]

LOW TIRE PRESSURE (if equipped) — Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating your tires in the T ires, Wheels and Loading chapter . TIRE PRESSURE MONITOR F AUL T (if equipped) — Displayed when the T ire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on,[...]

ENGINE TURNS OFF IN XX (Diesel engine only) — Displayed when the vehicle is in the final 30 seconds of a countdown to where the engine will intentionally be turned off by the PCM. The diesel engine shutdown is a (regulatory) requirement which may be required of a particular diesel vehicle for sale in states requiring this feature. Refer to your P[...]

CLEANING EXHAUST FIL TER (Diesel engine only) — Displayed when the vehicle has entered the cleaning mode. V arious engine actions will raise the exhaust temperature in the Diesel Particulate Filter (DPF) system to burn off the particles (exhaust soot). After the particles are burned off, the exhaust temperature will fall back to normal levels. Th[...]

OPTIONAL MESSAGE CENTER (IF EQUIPPED) Y our vehicle’ s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with an informational message followed by a long indicator chime. The message center display is located in the instrument cluster . Selectable features Info (in[...]

DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display . The running average fuel economy is re-initialized to a factory default value if the battery is disconnected. XX.X MPG (L/100km) A verage fuel economy displays[...]

System check and vehicle feature customization Press the SETUP button repeatedly to cycle the message center through the following features: Note: When returning to the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed to change back to English. Press and hold the RESET button to change back to Englis[...]

T o reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or 12 months) perform the following: 1. Press and release the SETUP button to display “OIL LIFE XXX% HOLD RESET = NEW”. 2. Press and hold the RESET button for two seconds and release to reset the oil life to 100%. Note: T o change oil life 1[...]

Usually , when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary . Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point[...]

8. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWL Y TO CALIBRA TE display changes to CALIBRA TION COMPLETED. It will take up to five circles to complete calibration. 9. The compass is now calibrated. Note: If the RESET button is pressed or three minutes has expired, the display will go back to the INFO menu a[...]

DRIVER DOOR AJAR — Displayed when the driver’ s door is not completely closed. P ASSENGER DOOR AJAR — Displayed when the passenger’ s door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed. FUEL LE[...]

TIRE PRESSURE SENSOR F AUL T (if equipped) — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Y our T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter . If the warning stays on or cont[...]

DRIVE TO CLEAN EXHAUST FIL TER (Diesel engine only) — Displayed when the Diesel Particulate Filter (DPF) is full of particles (exhaust soot) and the vehicle is not being operated in a manner to allow normal cleaning. This message will stay on until the exhaust filter cleaning has begun, at which time the CLEANING EXHAUST FIL TER message will be d[...]

EXHAUST FIL TER DRIVE COMPLETE (Diesel engine only) — Displayed when the Diesel Particulate Filter (DPF) has been adequately cleaned after the DRIVE TO CLEAN EXHAUST FIL TER followed by CLEANING EXHAUST FIL TER messages have been displayed. This message is NORMAL. Refer to your Power Stroke 6.0 and 6.4 Liter Direct Injection T urbo Diesel Owner?[...]

AUDIO SYSTEMS AM/FM stereo system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only us[...]

2. AUDIO: Press AUDIO repeatedly to gain access to the following settings: TREB (T reble): Press AUDIO to reach the treble setting. Use / / SEEK . BASS (Bass): Press AUDIO to reach the bass setting. Use / / SEEK . BAL (Balance): Press AUDIO to reach the balance setting. Use / / SEEK to adjust between the left and right speakers. Setting the clock: [...]

7. CLK (Clock): Press CLK to toggle between the clock and radio frequency . AM/FM stereo single CD/satellite compatible sound system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus o[...]

In satellite radio mode (if equipped) , press / to tune to the next/previous channel. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . 2. (Phone): If your vehicle is equipped with SYNC 威 , press to access SYNC PHONE features. For further information, please refer to sup[...]

• DELETE SONG: Press OK to delete a song title from the system’ s memory . Press / to cycle through the saved songs. When the song title appears in the display that you would like to delete, press OK. The song will appear in the display for confirmation. Press OK again and the display will read SONG DELETED. If you do not want to delete the cur[...]

F ADE: Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the back (B) and front (F) speakers. SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder with increasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to a[...]

5. SEEK: In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), press SEEK, SEEK to seek to the previous/next channe[...]

8. FOLDER : In folder mode, press FOLDER to access next folder on MP3 discs, if available. 9. FOLDER: In folder mode, press FOLDER to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: T o[...]

In satellite radio mode (if equipped), press and hold to hear a brief sampling of the next channels. Press again to stop. In CA TEGORY MODE, press SCAN to hear a brief sampling of the channels in the selected category . Press again to stop. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer f[...]

Premium/Premium plus in-dash six CD/MP3/satellite compatible sound system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the [...]

Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . 2. (Phone): If your vehicle is equipped with SYNC 威 , press to access SYNC PHONE features. For further information, please refer to supplemental information on SYNC 威 included with your vehicle. If your vehicle is not e[...]

• DELETE SONG: Press OK to delete a song from the system’ s memory . Press / to cycle through the saved songs. When the song appears in the display that you would like to delete, press OK. The song will appear in the display for confirmation. Press OK again and the display will read SONG DELETED. If you do not want to delete the currently liste[...]

T o search for specific RBDS music categories: When the desired category appears in the display , press / to find the desired type, then press and release SEEK, SEEK or press and hold SCAN to begin the search. T o view the station name or type: When the desired category appears in the display , press TEXT/SCAN to toggle between displaying the stati[...]

In Folder mode, pressing SEEK will scroll only through tracks within the selected folder . Press FOLDER, FOLDER to access the previous/next folder (if available). COMPRESS (Compression): A vailable only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display . Use / / SEEK, SEEK to toggle ON/OFF . When COMPRESS is ON, the system wil[...]

6. / OK (Play/Pause): This control is operational in CD/MP3 mode. When a CD/MP3 is playing, press to pause or play the current CD. The CD status will display in the radio display . OK: Use in various menu selections. If your vehicle is equipped with a Family Entertainment System (FES) please refer to the Family entertainment DVD system section late[...]

In satellite radio mode (if equipped) , there are 18 available presets, six each for SA T1, SA T2 and SA T3. T o save satellite channels in your memory presets, tune to the desired channel then press and hold a preset control until sound returns. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized de[...]

17. LOAD: T ol o a dad i s ci n t ot h e system, press LOAD. Select a slot number using memory presets 1–6. When the display reads LOAD CD#, load the desired disc, label side up. If you do not choose a slot within five seconds, the system will choose for you. Once loaded, the first track will begin to play . T o auto load up to 6 discs, press and[...]

Y our vehicle may be equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack, located on the instrument panel below the power point, provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity . T o [...]

T roubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2. Do not set the portable music player’ s volume level higher than [...]

Y our vehicle may be equipped with a USB port located on the instrument panel. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature. For further information on this feature, refer to Accessing and using your USB port in the SYNC 威 supplement or Navigation System supplemen[...]

• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not[...]

MP3 track and folder structure Y our MP3 system recognizes MP3 individual tracks and folder structure as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. For more information on track and folder mode, refer to Sample MP3 structure in the following section. • MP3 track mode igno[...]

Satellite radio information (if equipped) Satellite radio channels: SIRIUS broadcasts a variety of music, news, sports, weather , traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS satellite radio channels, visit www .sirius.com in the United States, www .sirius-canada.ca in Canada, or call SIRIUS[...]

Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes. Satellite Radio Electronic Serial Number (ESN): This 12–di[...]

Radio Display Condition Action Required NO TEXT Artist information not available. Artist information not available at this time on this channel. The system is working properly . NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category informati[...]

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use [...]

3. Press the power button on the DVD player , then press Play to begin to play the disc. If a DVD is already loaded into the system, press PLA Y on the DVD player . Note: If sound can be heard, but no video is present, press VIDEO to select the video source (DVD or aux-inputs). Note: If your vehicle is equipped with a navigation system, when a disc[...]

3. The disc will begin to play and the ‘CD Audio Disc’ screen will display . From this screen, you can also select from COMPRESSION, SHUFFLE and SCAN features. Note: If your vehicle is equipped with a navigation system, when a disc is inserted, the DVD system will automatically switch to dual-play mode; the rear speakers will turn off, and the [...]

2. Press the power button to turn the DVD system on. The indicator light next to the power button will illuminate. 3. Connect an auxiliary audio/video source by connecting RCA cords (not included) to the RCA jacks on the left hand side of the system. • Y ellow (1) — video input • White (2) — left channel audio input • Red (3) — right ch[...]

• If your vehicle is equipped with a radio: a. Press the headphone/speaker ( / ) button on the remote control or DVD system. Press again to return to single play mode. b. Press the 2 and 4 memory presets on the radio at the same time. Press again to return to single play mode. A green light will illuminate next to either the A or B Headphone Cont[...]

T o adjust display brightness: T o decrease/increase the brightness level on the display screen, press the brightness control on the DVD system. A display will appear at the bottom of the screen indicating the brightness level. The brightness display will only appear when the menu is not displayed. DVD player controls 1. Headphone control A/B: Whil[...]

2. / (Stop/Eject): Press once to stop and press a second t i m et oe j e c tad i s cf r o mt h eD V D system. 3. (Reverse): Press and release for the previous chapter or track. Press and hold to reverse search a DVD, Video CD, or FES CD in DVD/CD mode. 4. (Fast forward): Press and release for the next chapter or track. Press and hold to forward sea[...]

10. V olume: If your vehicle is equipped with a navigation system, this function is only available when in dual play mode. For all other vehicles, when in single play mode, press to increase ( ) or decrease ( ) the volume over all speakers. When in Dual Play , press to increase ( ) or decrease ( ) the volume for the wired headphones. (W ireless hea[...]

15. ENTER: Press to select/confirm the current selection. 16. Cursor /Brightness controls: Use the cursor controls to make various selections when in any menu. When not in a menu, and in DVD mode, press / to adjust the brightness. A display bar will appear at the bottom of the screen indicating the brightness levels. Remote control Unless otherwise[...]

3. DISPLA Y : Press to access the on-screen display of the FES functions and adjustments. 4. RETURN: Press to return to the previous menu screen. 5. ANGLE (DVD dependent): Press to select the angle to view the scene. 6. Channel A/B: Press to select either A or B headphones and then use the MEDIA control to select the desired playing media for the h[...]

18. Fast reverse/Previous: When a DVD is playing, press and hold for a quick reverse within the DVD. Press and release for the previous chapter . Press PLA Y to resume normal playback speed and volume. In CD/MP3 mode, press to access the previous track. 19. MENU: Press to access the DVD disc menu for selections. Press MENU again when in the DVD dis[...]

Headphones Wireless headphones W ARNING: The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens, which could result in a crash causing serious injury . Give your full attention to driving and to the road. Y our FES system is equipp[...]

T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing. Entertainment Systems 80 2010 F-250/350/450/550 (f23) Owners G[...]

T o operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment. • Select the desired audio source (Channel A or B) for e[...]

Wired headphones W ARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. W ARNING: The driver should never use the headphones while driving the vehicle. Using[...]

Single Play: Single play consists of all occupants in the vehicle listening to the same playing media over the front and rear speakers. When the DVD system is on, and the same source is playing through the front and rear speakers, SINGLE PLA Y will appear in the front radio display . Dual Play: Dual play is when the rear seat passengers choose to l[...]

Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B. Press MEDIA to change the audio source for Channel B. This information will displa[...]

Menu mode Press MENU once on the DVD system to access the DVD disc menu if available. Press MENU twice to access the DVD set-up menu and the following features: 1. ZOOM 2. ANGLE 3. ASPECT RA TIO 4. LANGUAGE 5. SUB TITLES Angle mode Select ANGLE to select various angles of view for the DVD. This is disc dependent — some DVD discs may have more vie[...]

Y ou can select from: WIDE, LETTER BOX or P AN SCAN. Once you have made your selection, press ENTER to confirm. The LCD screen display will immediately change to your selection after the system resumes playback of the DVD. The system default is WIDE (16:9). Language Select LANGUAGE to select the language you would like to use for audio output (Engl[...]

Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs T o play audio CDs on your DVD system: 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Ensure that the DVD system is on. 3. Insert an audio CD into the DVD system, label side up. 4. The track and elapsed time will appear in the sta[...]

4. The folder , track and elapsed time will appear in the status bar . The screen will list the Artist, T itle, Album and File Name. COMP (Compression): Compression brings soft and loud CD/MP3 passages together for a more consistent listening level when in CD mode. Press to turn the feature on/off. SHUFFLE: Press to hear all tracks on the current M[...]

CD, MP3 and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into the slot of the CD player (if equipped). • Always store discs out of direct sunlight. Excessive heat may damage or war[...]

4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD. Press and release to go to the previous chapter . Press and hold for a fast reverse search. Press and release to go to the next chapter . Press and hold for a fast forward search. Press when not in menu mode to adjust brightness, or when in menu mode to na[...]

2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system. They can be used to plug in wired headphones or to connect and play au[...]

Audio displays Y our DVD system interacts closely with the front audio system. Status messages will appear in the radio display showing the DVD status. Some possible radio display messages: • SINGLE PLA Y or DUAL PLA Y • DVD LOAD • DVD MENU • DVD STOP Audio interaction Y ou can then also use the front audio controls to advance, reverse, pla[...]

LOCKED (disabled): The FES buttons are locked and all FES button presses are ignored by the radio and the FES except for load and eject. When the DVD system is ON, you can then press the memory preset controls 2 and 4 simultaneously to toggle between Single Play and Dual Play . In Single Play mode, all speakers listen to the same media. In Dual Pla[...]

Safety information W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell phones and other devic[...]

cables where they will not be stepped on or interfere with the operation of seats and/or compartments. Disconnect video games and video equipment power cords and/or cables when not in use. A void touching auxiliary input jacks with your fingers. Do not blow on them or allow them to get wet or dirty . Do not clean any part of the DVD player with ben[...]

Humidity and moisture condensation Moisture in the air will condense in the DVD player under extremely humid conditions or when moving from a cold place to a warm one. Moisture condensation may cause damage to the DVD and/or player . If moisture condensation occurs, do not insert a CD or DVD into the player . If one is already in the player , remov[...]

• When a disc is inserted into the FES while in Headphone Only Mode, both headphone channels (A and B) will be connected to FES-DISC. NAVIGATION SYSTEM (IF EQUIPPED) Y our vehicle may be equipped with a navigation system. Refer to the Navigation System supplement for further information. SYNC 姞 (IF EQUIPPED) Y our vehicle may be equipped with S[...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outs[...]

3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. MANUAL HEATING AND AIR CONDITIONING SYSTEMS (IF EQUIPPED) • Manual heating and air conditioning system • Manual[...]

2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior[...]

• Do not put objects under the front seats that will interfere with the airflow to the rear seats. • Remove any snow , ice or leaves from the air intake area at the base of the windshield. • T o improve the A/C cool down, drive with the windows slightly open for 2–3 minutes after start up or until the vehicle has been “aired out.” Durin[...]

DUAL AUTOMATIC T EMPERATURE CONTROL (DA TC) SYSTEMS (IF EQUIPPED) • DA TC • DA TC with heated mirrors Climate Controls 102 2010 F-250/350/450/550 (f23) Owners Guide, 1st Printing USA (fus)[...]

• DA TC with heated seats and heated mirrors T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter In order to achieve maximum cooling performance, press , A/C, , and set the temperature to 60°F (16°C) and[...]

4. Recirculation control: Press to activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculation can be engaged manually in any other airflow selection except (defrost). Recircul[...]

Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle, do not drive with the system off, or with recirculated air engaged and A/C off. • Do not put objects under the front seats that will interfere with the airflow to the[...]

In (panel) or (panel/floor) modes: 1. Move temperature control to full cold. 2. Select A/C and (recirculated air). Use recirculated air with A/C to provide colder airflow . 3. Set highest fan speed initially , then adjust to maintain comfort. T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temper[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also kee[...]

Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the on position, • the headlamp control is in the off or parking lamp position and • the parking brake must be disengaged. W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . Th[...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable illuminated switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Note: If the battery is disconnected, discharged, or a new battery is installed, the dimm[...]

V ertical and horizontal aim adjustment (sealed beam headlamps) The headlamps on your vehicle are intended to be aimed using mechanical aimers. If mechanical aimers are used and the cross-car sight line is in any way blocked, set the legs of the universal adaptor all to the same setting, such that the cross-car sight line is no longer blocked, per [...]

5. Locate the vertical adjuster (2) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down). 6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or s[...]

• (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 3. T urn on the low beam headlamps to illuminate the wall or sc[...]

MAP LAMPS (IF EQUIPPED) The dome lamp turns on when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is off. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in press[...]

Replacing exterior bulbs Check the operation of all the bulbs frequently . Function Number of bulbs T rade number Headlamps (aerodynamic) 2 H13/9008 Headlamps (sealed beam) 2 H6054 Park lamp with aerodynamic headlamp 2 3157A or 3157AK Park lamp with sealed beam headlamp 2 3157 Sidemarker 2 194 T ail/stop/turn/sidemarker (pick-up only) 2 3157 T ail/[...]

Replacing headlamp bulbs (aerodynamic) 1. Make sure that the headlamps are off, then open the hood. 2. Remove the bolts from the top, side and bottom of the headlamp assembly . 3. Pull the assembly straight out disengaging two snap clips from the fender . 4. Disconnect the electrical connector by squeezing the release tab and pushing the connector [...]

Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1. Make sure that the headlamps are off, then open the hood. 2. Remove the bolts from the top, side and bottom of the headlamp assembly . 3. Pull the assembly straight out. 4. Remove the bulb assembly , sidemarker or park/turn bulb by turning it counterclockwise and pulling it straight out[...]

Replacing park/turn/sidemarker bulbs (sealed beam) 1. Make sure that the headlamps are off, then open the hood. 2. Remove the three screws and one bolt from the top and bottom of the park lamp/bezel assembly . 3. Pull the assembly straight out disengaging snap clip. 4. Remove the bulb assembly , sidemarker or park/turn by turning it counterclockwis[...]

Replacing brake/tail/turn/back-up lamp bulbs - Chassis cabs only (if equipped) 1. Make sure the headlamps are off. 2. Remove the four screws and the lamp lens from lamp assembly . 3. Carefully pull the bulb straight out of the socket and push in the new bulb. Replacing cargo lamp and high-mount brakelamp bulbs 1. Make sure the headlamps are off. 2.[...]

Replacing fog lamp bulbs (if equipped) 1. Make sure the headlamps are off. 2. Remove the bulb socket from the fog lamp by turning counterclockwise. 3. Disconnect the electrical connector from the fog lamp bulb. Install the new bulb(s) in reverse order . Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . [...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically adjust with the vehicle speed. The faster your[...]

TILT STEERING WHEEL 1. Pull and hold the steering wheel release control toward you. 2. Move the steering up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. W ARNING: Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQU[...]

Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object and the front tab can be used for holding tickets, paper , envelopes, etc. The front bin may be used to store small objects. CENTER CONSOLE (IF EQUIPPED) Y our vehicle may be e[...]

Center console/under-seat storage-Cabela’ s Edition (if equipped) Y our vehicle may be equipped with a lockable compartment in the center console and a lockable storage area under the rear seats. Center console storage Use the vehicle’ s ignition key to lock/unlock the compartment. Under -seat storage Flip the rear seat cushion up to access the[...]

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet for this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . Auxiliary pow[...]

Press and pull the window switches to open and close windows. • Press down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. Rear W indow Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviat[...]

W ARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. If your vehicle is equipped with a power rear slide window , the switch is located on the instrument panel behind the right-hand side of the steering wheel. • Press the rig[...]

Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a rearview camera system (RCS), a video image will display in the mirror or the navigation system (if equipped) when the vehicle is put in (R) Reverse. As you shift into any other gear from R (Reverse), the i[...]

Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Powerfold mirrors If equipped with powerfold mirrors, you can fold the side mirrors simultaneously using the power mirror switch. T o operate the powerfold mirrors: 1. Rotate the switch to the center/neutral position. 2. Momentari[...]

Note: T en or more switch activations within one minute, or repeated fold/unfolding of the mirrors while holding the switch rearward during the full travel may cause the system to disable the fold/unfold function to protect the motors from overheating. Should this occur , wait approximately 3 1 ⁄ 2 minutes for the system to reset and function to [...]

• T o telescope the mirrors inboard, press and hold the right side of the power telescope switch until the mirrors reach their desired position. Memory mirrors (if equipped) This system allows automatic positioning of the outside rearview mirrors. For more information on this feature, refer to Memory seats/power mirrors/adjustable pedals in the S[...]

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. W ARNING: Never adjust the accelerator and brake pedal with feet on t[...]

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. No[...]

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET [...]

Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED)[...]

In AM, FM1, or FM2 mode: • Press SEEK to select preset stations within the selected radio band or press and hold to select the next/previous radio frequency . In Satellite radio mode (if equipped): • Press SEEK to advance through preset channels or subscribed channels. In CD mode: • Press SEEK to select the next selection on the CD or press a[...]

SYNC 威 system hands free control feature (if equipped) Press VOICE briefly until the voice icon appears on the display to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold VOICE to exit voice command. Press to activate phone mode or answer a phone call. Press and hold to end call [...]

UPFITTER CONTROLS (IF EQUIPPED) Y our vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3 and AUX 4. These switches will only operate while the ignition is in the on position, whether the engine is running or not. It is, however , recom[...]

There will also be one power lead for each switch found as a blunt-cut and sealed wire located below the instrument panel and to the left of the steering column. They are coded as follows: Switch Circuit number W ire color Fuse AUX 1 CAC05 Y ellow 30A AUX 2 CAC06 Green with Brown T race 30A AUX 3 CAC07 Violet with Green T race 10A AUX 4 CAC08 Brown[...]

and release the control again to fully open. T o stop the one-touch open feature, press either the or control again. W ARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening. T o close the moon roof: Press and hold the control until[...]

detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink 威 at: www .homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink 威 equipped vehicle purcha[...]

4. At the garage door opener receiver (motor -head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer .) Note: There are 30 seconds in whi[...]

Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used a[...]

T AILGATE LOCK (IF EQUIPPED) Y our vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • T urn ignition key to the left to unlock. T ailgate removal Y our tailgate is removable to allow more room for loading. W ARNING: Always properly secure car[...]

4. Lower the tailgate. 5. Using a screwdriver , gently pry the spring clip (on each connector) past the head of the support screw . Disconnect cable. 6. Disconnect the other cable. 7. Lift tailgate to a 45-degree angle from horizontal. 8. Lift right side off of its hinge. 9. Lift tailgate to a 80-degree angle from horizontal. 10. Remove tailgate fr[...]

• Always use grab handle when stepping up and down. • Step not intended for bare-footed use. • Keep step clean from contamination before use (e.g. snow , mud) • Keep the step load (you + load) below 350 lb (159 kg). • Never drive with step deployed. T o close the tailgate step: 1. Close the step panel, then lift and fully close the tailga[...]

2. Open the latches to release the panels. 3. Rotate the panels toward the tailgate. Repeat Steps 1–3 for the other side of the bed extender . 4. Connect the two panels, then rotate both knobs a quarter -turn clockwise to secure the panels. Driver Controls 146 2010 F-250/350/450/550 (f23) Owners Guide, 1st Printing USA (fus)[...]

5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reverse steps for storage of the bed extender . Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged. Note: Ensure all cargo is secured. Note: When the vehicle is in mo[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock 威 Passive Anti-theft system, your keys are electronically coded to your vehicle; using a non-coded key will not permit your vehicle to start. If yo[...]

Autolock feature (if equipped) The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater than two seconds. The autolock feature repeats when: • any [...]

5. T urn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. T o enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activa[...]

• using a keypad procedure (if equipped) Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the p[...]

CHILDPROOF DOOR LOCKS (IF EQUIPPED) • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatica[...]

Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to your authorized dealer in order to aid [...]

2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will illuminate once more. If any of the doors are not properly closed the horn will make two quick chirps and the parking lamps will not flash. Car finder Press twice [...]

Deactivating the memory feature T o deactivate this feature: 1. Press and hold either memory 1 button or memory 2 button for five seconds. A tone will be heard after 1 1 ⁄ 2 seconds when the memory store is done, continue to hold until a second tone is heard after five seconds. 2. W ithin three seconds press the button on the keyfob The keyfob un[...]

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. Note : If your vehicle is equipped w[...]

Illuminated entry The interior lamps and parking lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the lights if: • the ignition switch is turned to the on position, or • the remote transmitter lock control is pressed, or • the 7 • 8 and the 9 • 0 controls on the keyles[...]

4. T o associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not[...]

Unlocking and locking the doors using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other . The interior lamps will illuminate after entering a valid keypad entry code. T o unlock all doors, press the 3 • 4 control within five secon[...]

Anti-theft indicator The anti-theft indicator is located in the instrument cluster . V ehicles equipped with the SecuriLock 威 Passive Anti-theft system behave as follows: • When the ignition is in the off position, the indicator will flash once every two seconds for a total of 10 seconds to indicate the SecuriLock 威 system is functioning as a[...]

Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock 威 keys can be used. T o program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the [...]

If not successful, the new coded key(s) will not start the vehicle’ s engine and the theft indicator will flash on and off and you may repeat Steps 1 through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed. PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn yo[...]

SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W ARNING: Before returning the seatback to its original position[...]

Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward. • Pull up on the lever located at the side of the seat cushion to recline the seatback and to return the sea[...]

40/20/40 front seat armrest and console (if equipped) T o release the armrest, pull forward on the strap and pull the armrest down. T o gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position. Lift up armrest to return it to a center seatback. Seating and Safety Restra[...]

Captain’ s chair (if equipped) • Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • T o recline the seatback, pull the release lever handle located on the side of the seat up. • Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward. Adj[...]

Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support The lumbar support control is located on the outboard side of the seat T urn the lumbar support clockwise for more s[...]

Heated seats (if equipped) The heated seat control is located on the climate control panel. W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater . The seat hea[...]

T o recall a memory position: • Press and release either memory 1 button or memory 2 button. A position can be recalled: • in any gearshift position if the ignition is not in the on position. • only in P (Park) or N (Neutral) if the ignition is in the on position. A memory seat position may be programmed at any time. The memory positions are [...]

Push control to lower head restraint. W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion. Cabela’ s 姞 se[...]

T o flip the seat cushion up, pull up on the lever located on the side of the seat cushion to rotate the cushion up until it locks into a vertical storage position, gaining access to the grocery hook located on the underside of the driver -side seat cushion. The maximum load is 25 lb. (11 kg). Returning the seat to seating position • Pull lever o[...]

T o gain access to the 60/40 load floor , store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor , and rotate forward until resting on the carpet. SAFETY RESTRAINTS Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the[...]

W ARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder . 3) N[...]

2. T o unfasten, push the release button and remove the tongue from the buckle. V ehicle sensitive mode Combination lap and shoulder belts in normal retractor mode allow free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply , or the ve[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the a[...]

W ARNING: BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer . Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Energy management featur[...]

Front safety belt height adjustment The front outboard seating positions are equipped with safety belt height adjusters. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . W ARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the s[...]

1. T o lengthen the lap belt, pull some webbing out of the shoulder belt retractor . 2. While holding the webbing below the tongue, grasp the tip (metal portion) of the tongue so that it is parallel to the webbing and slide the tongue upward. 3. Provide enough lap belt length so that the tongue can reach the buckle. How to fasten the cinch tongue ([...]

Lap belts Adjusting the lap belt W ARNING: The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 1st row center seating position on SuperCab and Crew Cab The lap belt does not adjust automatically . Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our [...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

Belt-Minder 威 activation and deactivation procedure 1. T urn the ignition switch to the on position. (DO NOT ST ART THE ENGINE) 2. W ait until the safety belt warning light turns off. (Approximately 1 minute) • Step 3 must be completed within 60 seconds after the safety belt warning light turns off. 3. Buckle then unbuckle the safety belt 9 tim[...]

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; t h e r ei sar i s ko fi n j u r yf r o ma deploying airbag. W ARNING: All occupants of the vehicle, including the[...]

W ARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. T o properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly one or two degrees from the upright posit[...]

Children and airbags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Failure to follow these instructions may increase the risk of injury in a collision. W ARNING: An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a [...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

The diagnostic module monitors its own internal circuits and the supplemental airbag electrical system wiring (including the impact sensors), the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a t[...]

Passenger airbag ON/OFF switch (if equipped) W ARNING: An airbag ON/OFF switch (if equipped) may be installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings. Failure to put the switch in a proper position can increase the risk [...]

W ARNING: An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. Turning the passenger airbag back on The passenger airbag remains OFF until you turn it back ON. 1. Insert the ign[...]

W ARNING: If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . DO NOT place a child in a rear facing infant seat in the front seat unless your vehicle is equipped with an airbag ON/OFF switch and the passenger airbag is turned OFF . This is because[...]

2. Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: • the vehicle has no rear seat; • although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle; or • the child has a medical condit[...]

2. Child age 12 or under: A child age 12 or under must ride in the front seat because: • my vehicle has no rear seat; • although children age 12 and under ride in the rear seat whenever possible, children age 12 and under have no option but to sometimes ride in the front seat because rear seat space is insufficient; or • the child has a medic[...]

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device [...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.45 meters) tall, are greater than age four (4) and less than age twelve (12), and between[...]

Recommendations for attaching child safety restraints for children Note: This vehicle is not equipped with LA TCH lower anchors. Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lowe[...]

W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age. Follow the child restraint manufacturer’ s instructions and warnings provided for installation and use in conjunction with the ins[...]

training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle. T o locate a child seat fitting station[...]

Installing child safety seats with automatic locking mode combination lap and shoulder belts (front passenger and rear outboard seating positions) Check to make sure the child seat is properly secured before each use. Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be seated a[...]

1. Position the child safety seat in a seat with a combination lap and shoulder belt. W ARNING: An airbag can kill or injure a child in a child seat. Child seats should NEVER be placed in the front seats, unless the passenger airbag switch is turned off, See Passenger airbag on/off switch . W ARNING: Rear facing child seats should NEVER be placed i[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

8. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the additional weight of the child is added to the child restraint[...]

Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in the center seat. W ARNING: Airbags can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. W ARN[...]

4. Insert the belt tongue into the proper buckle for that seating positions until you hear a snap and feel it latch. Make sure the tongue is securely latched to the buckle by pulling on the tongue. 5. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling [...]

7. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward. There should be no more than one inch (2.5 cm) of movement for proper installation. 8. Ford recommends checking with a NHTSA[...]

2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions. 4. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the b[...]

The passenger seats of your vehicle may be equipped with built-in tether strap anchors located behind the seats as described below . The tether anchors in your vehicle may be straps on the seatback or an anchor bracket on the rear edge of the seat cushion or an anchor bracket mounted to the body shell on the back panel. The SuperCab rear seat has t[...]

T ether strap attachment 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, other wise route the tether strap over the top of the seatback. If the top of the safety seat hits the head restraint, rai[...]

• Front seat (SuperCab) • Rear seats (Crew Cab) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats with combination lap and shoulder belts section of this chapter for further instructions to secure the child safety seat. 7. T [...]

These straps may be secured below the back of the seat with rubber bands. T o access, reach below the back of the seat and pull tether loop out of the rubber band securing it. Many tether straps cannot be tightened if the tether strap is hooked to the loop directly behind the child seat. T o provide a tight tether strap: 1. Route the tether strap t[...]

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit of the vehicle safety belt. Children outgrow a typical child seat (e.g., convertible or toddler seat) when they weigh about 40 lb (18 kg) and are around four (4) years of age. Consult your child safety seat owner guide for the weight, height, and age limits s[...]

Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat cushion? • Can the child sit without slouching? • Does the lap belt rest low across the hips? • Is the shou[...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

VEHICLE CHARACTERISTICS 4WD and A WD Systems (if equipped) A vehicle equipped with A WD or 4WD (when selected) has the ability to use all four wheels to power itself. This increases traction which may enable you to safely drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Power is supplied to all four wheels [...]

How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. • Shorter – to give it the capability to appr[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are determined by standards th[...]

W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to [...]

• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard [...]

W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It al[...]

T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. T ire service, including adjusting tire pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safet[...]

W ARNING: Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that m[...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (138[...]

W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Highway hazards No mat[...]

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved [...]

• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair . After tire rotation, inflation pressures must be adjusted for the tires new position[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label, which is located on the B-Pillar or the edge of the driver’ s door , for the correct tire pressure for your vehicle. 12. T readwear , T raction and T emperature Grades • T readwear: The treadw[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA)[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the v[...]

following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically ([...]

T o restore the full functionality of the Tire Pressure Monitoring System, have the damaged road wheel/tire repaired and remounted on your vehicle. For additional information, refer to Changing tires with TPMS in this section. When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

TPMS reset procedure The TPMS reset procedure needs to be performed after each tire rotation on vehicles that require different recommended tire pressures in the front tires as compared to the rear tires. W ARNING: T o determine the required pressure(s) for your vehicle – refer to the Safety Compliance Certification Label or T ire Label located o[...]

3. Cycle the ignition to the on position with the engine off. 4. T urn the hazard flashers on then off 3 times. This must be accomplished within ten seconds. If the reset mode has been entered successfully , the horn will sound once, the TPMS indicator will flash and the message center (if equipped) will display TRAIN LEFT FRONT TIRE . If this does[...]

8. Remove the valve cap from the valve stem on the right rear tire. Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire. Decrease the air pressure until the horn sounds. T raining is complete after the horn sounds for the last tire trained (driver’ s side rear tire), the TPMS tell tal[...]

• Drive cautiously . If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. • The suspens[...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label). Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEV[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires,[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . Tires, Wheels and Loading 247 2010 F-250/350/450/550 (f23) Owner[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations. W ARNING: Exceeding any vehicle weight rating limitation could result in [...]

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (4[...]

T RAILER TOWING Note: The trailer towing charts in this section apply to vehicles equipped with gasoline engines; for vehicles equipped with diesel engines, refer to your Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement. Y our vehicle may tow a Conventional/Class IV trailer or fifth wheel trailer provided the maximum trailer [...]

Maximum GCWR - lb. (kg.) Engine Rear axle ratio Manual transmission Automatic transmission F–250 Pick-up 5.4L 3.73 15000 (6804) 16000 (7257) 4.10 17000 (7711) 18000 (8165) 6.8L 4.10 20000 (9072) 21000 (9525) 4.30 22000 (9979) 22500 (10206) F–350 Single Rear Wheel (SR W) Pick-up 5.4L 3.73 15000 (6804) 16000 (7257) 4.10 17000 (7711) 18000 (8165) [...]

Hitches W ARNING: ON PICK-UP TRUCKS, the trailer hitch provided on this vehicle enhances collision protection for the fuel system. DO NOT REMOVE! Do not mount a ball hitch (sometimes referred to as a trailer ball hitch or trailer ball) to the bumper or use hitches that clamp onto the vehicle’ s bumper or attach to the axle. Y ou must distribute t[...]

W ARNING: T owing trailers beyond the maximum tongue weight exceeds the limit of the towing system and could result in vehicle structural damage, loss of vehicle control and personal injury . Weight distributing hitch When hooking up a trailer using a load equalizing hitch, always use the following procedure: 1. Park the unloaded vehicle on a level[...]

T railer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulations. W ARNING: If you own a trailer with a hydraulic brake system, do not connect the trailer’ s hydraulic brake system direc[...]

The trailer brake controller (TBC) is designed to display three items of information in the instrument cluster message center . These are: gain setting, output bar graph, and trailer connectivity status. They will appear as follows in the message center . • TBC GAIN = XX.X NO TRAILER : The instrument cluster message center will display the curren[...]

The GAIN should be set to provide the maximum trailer braking assistance while ensuring the trailer wheels do not lock when braking. Locked trailer wheels may lead to trailer instability . Note: This should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h). 1. Make sure the trailer brakes are in g[...]

to the trailer wiring; consult your trailer dealer for assistance. This can be a short to ground (i.e., chaffed wire) or a short to voltage (i.e., pulled pin on trailer emergency break-away battery) or trailer brakes drawing too much current. Note: Y our TBC can be diagnosed by your authorized dealer to determine exactly which trailer fault has occ[...]

Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed r[...]

• If you will be towing a trailer frequently in hot weather , hilly conditions, at GCWR, or any combination of these factors, consider refilling your rear axle with synthetic gear lubricant if not already so equipped. Refer to Maintenance Product Specifications and Capacities in the Maintenance and Specifications chapter for the proper axle lubri[...]

Backing up • Practice backing up, particularly if you are a novice. T urn the steering wheel to the right to move the trailer’ s rear end to the right. • Sharp steering movements may cause the trailer to jackknife or go out of control. Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the tra[...]

RECREATIONAL T OWING Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. These guidelines are designed to ensure that your transmission is not damaged. Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from e[...]

STARTING Positions of the ignition 1. Off— shuts off the engine and all accessories/locks the steering wheel and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the engine is not running. This position also unlocks the steering wheel. 3. On— all electrical circuits operational. W arning l[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. If your vehicle[...]

If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor . • T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning li[...]

Note: Cranking may be stopped at any time by turning the key to the off position. 3. After idling for a few seconds, release the parking brake, apply the brake, shift into gear and drive. Note: If the engine does not start on the first try , turn the key to the off position, wait 10 seconds and try Step 2 again. If the engine still fails to start, [...]

Prior to using the engine block heater , follow these recommendations for proper and safe operation: • For your safety , use an outdoor extension cord that is product certified by Underwriter’ s laboratory (UL ) or Canadian Standards Association (CSA). Use only an extension cord that can be used outdoors, in cold temperatures, and is clearly ma[...]

of power per hour . Y our factory installed block heater system does not have a thermostat; however , maximum temperature is attained after approximately 3 hours of operation. Block heater operation longer than 3 hours will not improve system performance and will unnecessarily use additional electricity . Make sure system is unplugged and properly [...]

Even when the ABS is disabled, normal braking is still effective. If your BRAKE warning lamp illuminates with the parking brake released, have your brake system serviced immediately by an authorized dealer . Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the eff[...]

Pull the release lever to release the parking brake. T o prevent the pedal from releasing too quickly , place your left foot on the service brake pedal, then slowly pull the release lever until the pedal slowly releases. Make sure that the pedal is fully released. Y ou may want to pull the release lever again to make sure the parking brake is fully[...]

into four -wheel drive mode (if equipped), the traction control system will be automatically disabled. T raction control operation will resume when the vehicle is placed back into two-wheel drive mode. W ARNING: Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or p[...]

• Heavy or uneven efforts may be caused by low power steering fluid. Check for low power steering pump fluid level before seeking service by your dealer . • Do not fill the power steering pump reservoir above the MAX mark on the reservoir , as this may result in leaks from the reservoir . If the power steering system breaks down (or if the engi[...]

PREPARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher cente[...]

If the fuse is not blown and the brakelamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake. T urn the ignition key to 1 (off), then remove the key . Locate the access cover plate for the brake-shift interlock override. It is located on top of the steering column sh[...]

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Understanding the shift positions of the 5–speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of se[...]

N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with T ow/Haul OFF D (Overdrive) with T ow/Haul OFF is the normal driving position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through g[...]

3 (Third) T ransmission starts and operates in third gear only . Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearsh[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that prevents cranking the engine unless the clutch pedal is fully pressed. T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral positi[...]

Shift according to the following shift speed charts: Upshifts when accelerating (recommended for best fuel economy) 6-speed transmission Shift from: T ransfer case position 1 (if equipped) 2H or 4H 4L LO-1 5 mph (8 km/h) 2 mph (3 km/h) 1-2 14 mph (23 km/h) 6 mph (10 km/h) 2-3 22 mph (35 km/h) 9 mph (14 km/h) 3-4 30 mph (48 km/h) 12 mph (19 km/h) 4 [...]

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. T urn the ignition off. W ARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . REVERSE SENSING SYSTEM (IF EQUIPPED) The[...]

The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system, located on the tailgate, provides a video image, which appears in the rearview mirror or on the navigation screen (if equipped), of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle. T o use the camera system, place the transm[...]

When shifting out of R (Reverse) and into any other gear , the image will remain on for a few seconds before it shuts off to assist in parking or trailer hookup. If equipped with the navigation system, after shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches 5 mph (8 km/h), only [...]

Night time and dark area use At night time or in dark areas, the camera system relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse lamps are operating in order to get a clear image in the dark. If either of the lamps are not operating, stop using the camera system, at least in the dark, until the lam[...]

• Some vehicles may be equipped with wheel ornaments that cover the 4x4 manual hub lock. These ornaments must be removed to access the manual hub locks. Electronic Shift On the Fly (ESOF) 4x4 system (if equipped) If equipped with the electronic shift 4WD System, and the instrument panel control is moved to 4X4 LOW while the vehicle is moving abov[...]

4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2WD, contact your authorized dealer as soon as possible. • 4x4 HIGH - momentarily illuminates after the engine is started. Illuminates when 4H (4x4 High) is engaged. Flashes when shifting into or o[...]

Shifting from 2H (2WD) to 4H (4x4 High) Engage the locking hubs by rotating the hub lock control from FREE to LOCK, then move the transfer case lever from 2H (2WD) to 4H (4x4 High) at a stop or a vehicle speed below 5 mph (8 km/h). • For proper operation, make sure that both indicator arrows on the hub are aligned, and that both hubs are set to L[...]

3. Move the transfer case shift lever through N (Neutral) directly to 4L (4x4 Low). 4. If the shift lever does not, or only partially moves to the 4L (4x4 Low) position, perform a shift with the transmission in N (Neutral) (or clutch pedal depressed) and the vehicle rolling at a speed below 5 mph (8 km/h). This will ensure the transfer case is full[...]

W ARNING: Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the Electronic Shift On the Fly (ESOF) 4x4 system (if equipped) Positions of the electronic shift system Note: Some noise may be heard as the 4WD system shifts[...]

Shifting from 4x4 HIGH to 2WD Rotate the 4x4 control to 2WD at any forward speed. Disengagement of the transfer case and front hubs may be delayed due to torque bind which is caused by driving on dry hard surfaces or performing tight turns while using the 4x4 system. • Yo u do not need to operate the vehicle in R (Reverse) to disengage your front[...]

3. Move the 4x4 control to the 4x4 HIGH or 2WD position. 4. Hold the shift conditions until the 4x4 LOW indicator light shuts off. 5. If the 4x4 LOW or 4x4 High indicator light flashes continuously for more than 10 seconds, allow the vehicle to move at a speed below 5 mph (8 km/h), then repeat steps 2 through 5 while the vehicle is rolling before r[...]

Basic operating principles • Do not use 4WD on dry , hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components. 4WD modes are only intended for consistently slippery or loose surfaces. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. ?[...]

Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Refer to T ransmission fluid temperature gauge in the Instrument Cluster chapter for transmission fluid [...]

transmission is in P (Park) or the manual transmission is in gear . Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the [...]

Note: If air is released from your tires, the T ire Pressure Monitoring System (TPMS) indicator light may illuminate (if equipped). Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if pos[...]

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. A void driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over . When[...]

Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. A void sudden braking as well. Although a 4WD veh[...]

Failure to maintain your vehicle properly may void the warranty , increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety . Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage. V EHICLE USED AS A STATIONARY PO[...]

the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water , always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. W et brakes do not stop the vehicle as quickly as dry brakes. SNOWPLOWING Ford recommends that the Super [...]

• The tire air pressures recommended for general driving are found on the vehicle’ s Safety Certification Label. The maximum cold inflation pressure for the tire and associated load rating is imprinted on the tire sidewall. T ire air pressure may require re-adjustment within these pressure limits to accommodate the additional weight of the snow[...]

W ARNING: Do not attempt to service, repair , or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer . W ARNING: Additional equipment such as snowplow equipment may effect the performance of the airbag sensors increasing the risk of injury . Please refer to the Body Builders Layout Book for i[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadsi[...]

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arranty’ s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our webs[...]

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. This switch is located on the passenger’ s side of the instrument panel. Open the front passenger door and[...]

FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage r[...]

Passenger compartment fuse panel The fuse panel is located in the passenger’ s footwell. Remove the panel cover to access the fuses. T o remove the fuse panel cover , pull the panel toward you. When the clips of the panel disengage, let the panel fall easily . T o remove a fuse use the fuse puller tool provided on the fuse panel cover . W ARNING:[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Not used (spare) 2 15A Not used (spare) 3 15A Family entertainment system (FES) 4 30A Not used (spare) 5 10A Keypad illumination, Brake-shift interlock (BSI), SPBJB 6 20A T urn signals 7 10A Left headlamp (Low beam) 8 10A Right headlamp (Low beam) 9 15A Int[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 11 10A Not used (spare) 12 7.5A Power mirror switch, Driver power seat (Memory) 13 5A Not used (spare) 14 10A Upfitter relay #3 feed 15 10A Climate control head 16 15A Upfitter relay #4 Feed 17 20A All lock motor feeds 18 20A Heated seat relay feed 19 25A Not used (spare) 20 15A Adjustable peda[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 33 10A T railer tow brake controller , T railer tow battery charge relay coil 34 5A Not used (spare) 35 10A Reverse sensing system (RSS), 4x4 module, 4x4 solenoid, T raction control switch, T ow/Haul switch (Diesel engine) 36 5A Passive anti-theft system (P A TS) transceiver , Cluster control 3[...]

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always repla[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 6 40A* Anti-lock brake system (ABS) module (Pump) 7 30A* Upfitter auxiliary switch #1 8 30A* Upfitter auxiliary switch #2 9 40A* ABS module (Coil) 10 20A* Instrument panel power point/cigar lighter 11 20A* Instrument panel power point 12 15A** Brake on/off (BOO) relay feed 13 5A** Brake switch,[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 28 20A* Heated mirror relay 29 30A* Passenger power seat 30 10A** A/C clutch relay 31 15A** Power fold mirror relay 32 20A** Fuel pump relay 33 20A** Back-up lamp relay 34 25A** T railer stop/turn relay 35 5A** ESOF relay coils 36 10A** Gasoline engines: Powertrain control module (PCM) keep ali[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 53 Relay PCM power bus (Fuses 68, 70, 72, 74, 76) (Diesel engine only) 54 Relay Starter solenoid 55 Relay T railer tow park lamps 56 Relay T railer tow battery charge 57 Relay Power Distribution Box (PDB) bus (fuses 67, 69, 71, 73, 75, 77) SJB Run /Start bus (Fuses 29–37, 46) 58 Relay ESOF hi[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 74 20A** Gasoline engines: V ehicle power (VPWR): Heated exhaust gas oxygen sensor , CMS, Mass air flow sensor , Electronic vapor management valve, CMCV , V ariable cam timing, IMTV Diesel engine: VPWR: Engine loads 75 5A** Back-up relay coil power 76 20A** Gasoline engines: VPWR: PCM Diesel en[...]

Dissimilar spare tire/wheel information W ARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only . This means that if you need to use it, you should replace it as soon as possible with a road tire/[...]

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a [...]

Stopping and securing the vehicle W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite to the tire being changed. Refer to the instruction sheet (located in the glove box) for detailed tire change instructions. Park on a lev[...]

T ool Location Jack handle, lug wrench, lug wrench extension (only available on Dual Rear Wheel [DRW] vehicles) and wheel chock (only available on Single Rear Wheel [SRW] vehicles equipped with a diesel engine) Regular cab: Fastened to floor behind driver seat SuperCab: Fastened to floor under rear seat Crew Cab: Fastened to floor behind rear seat [...]

2. Attach the spare tire lock key (A) to the jack handle (B). 3. Fully insert the jack handle (with one extension) through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resistance will be felt when turning the jack handle assembly . 4. T urn the handle counterclockwise and l[...]

W ARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. T urn engine off and block the wheel that is diagonally oppo[...]

• Front driver side (4x4) Note: Make sure the jack fits onto the flat area on the outboard side of the differential. • Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. • Rear Roadside Emergencies 321 2010 F-250/350/450/550 (f23) Owners Guide, 1[...]

Never use the front or rear differential as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 7. T urn the jack handle clockwise until the wheel is comple[...]

12. Position the jack according to the following guides: • Front (4x2): F–350 DRW Note: Place jack directly under I-beam. • Front driver side (4x4): F–350 DRW Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing. • Front passenger side (4x4): F-350 DRW Note: View shown from the rear of the vehi[...]

• Front: F–450/F–550 • Rear: F-350 DRW • Rear: F-450/F-550 13. Insert the jack handle into the pump linkage. 14. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’ s rated capacity . Roa[...]

15. Remove the lug nuts with the lug wrench. 16. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until t[...]

10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier . Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 20. Stow the jack, jack handle and lug wrench. Make sure the jack is [...]

If the ornament retention towers are aligned between the studs/lug nuts, the ornament is improperly installed. This improper installation may appear and sound correct, but will not keep the ornament on the vehicle. Ornaments improperly installed in this manner will fall off or become loose with minimal force or impact. Installing dual rear wheel or[...]

4. Be sure to install all the clips on the nuts over the flanges so that there is an even gap all around and the retention clips are fully seated. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the d[...]

5. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. 6. If removed, install the spare tire lock (if equipped) into the bumper drive tube with the spare tire lock key (if equipped)[...]

Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger . DO NOT apply gr[...]

4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect from any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive ([...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, [...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that the vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sli[...]

Note: T owing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatic transmission. Note: T owing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Not[...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB A[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. T elephone: ([...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • [...]

• After polishing chrome bumpers, apply a coating of Motorcraft 威 Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft 威 Premium Liquid W ax (ZC-53-A), [...]

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine bl[...]

• 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42). WINDOWS AND WIPER[...]

wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly . • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS (EXCEPT HAR[...]

INSTRUMENT PANEL AND CONSOLE (HARLEY-DAVIDSON ONLY) Y our vehicle’ s instrument panel and console are uniquely painted with both high and low gloss paints that require special care. The high gloss area is similar to that of the vehicle’ s exterior; the low gloss area is designed to help protect the driver from undesirable windshield reflection.[...]

• If grease or tar is present on the material, spot-clean the area first with Motorcraft 威 Spot and Stain Remover (ZC-14). In Canada, use Motorcraft 威 Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use househol[...]

LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREW CAB ONLY (IF EQUIPPED) Y our vehicle is equipped with seating covered in premium, top-grain leather which is extremely durable, but still requires special care and maintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintain the appearance of the leather [...]

Conditioning Bottles of King Ranch Leather Conditioner are available at the King Ranch Saddle Shop. Visit the W eb site at www.krsaddleshop.com ,o r telephone (in the United States) 1–800–282–KING (5464). If you are unable to obtain King Ranch Leather Conditioner , use another premium leather conditioner . • Apply your first conditioning tr[...]

Motorcraft 威 Engine Shampoo and Degreaser (U.S only) (ZC-20) Motorcraft 威 Engine Shampoo (Canada only) (CXC-66-A) Motorcraft 威 Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft 威 Premium Car W ash Concentrate (U.S. only) (ZC-17-B) Motorcraft 威 Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft 威 Premium Liquid W ax (ZC-53?[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Customer Information Guide to find out which parts and servi[...]

2. Block the wheels. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the fr[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. W indshield washer fluid reservoir 2. Battery 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. [...]

6.8L V10 gasoline engine 1. W indshield washer fluid reservoir 2. Battery 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10. Power distribution box Maintenance and Specifications 357[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. T urn the blade at an angle from the wiper arm. Press the lock tab to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at[...]

5. Locate and carefully remove the engine oil dipstick. • 5.4L/6.8L gasoline engines only; for diesel engine information, refer to the 6.0 and 6.4 Liter Direct Injection T urbo Diesel Owner’ s Guide Supplement. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is between the MIN and MAX marks, t[...]

3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level dipstick. 4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until three clicks are heard or until the cap is fully seated. T o avoi[...]

Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft 威 oil filter or another with equ[...]

W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. W ARNING: When lifting a plastic-cased battery , excessive pr[...]

• If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of au[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and underst[...]

• Do not mix coolants. Add the coolant type originally equipped in your vehicle. Refer to Maintenance product specifications and capacities in this chapter . Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems. This damage would not be covered under your veh[...]

4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir . If you removed the radiator cap in an overflow system, fill the radiator until the c[...]

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant an[...]

• The message center will indicate the engine is overheating. • The indicator will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. Howev[...]

FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not u[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The vehicle warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. W ARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor [...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some stations offer fuels posted as “Regular” with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. Do not be concerned if your engine sometimes kn[...]

Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a f[...]

For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling.[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • T o maximize the fuel economy , drive with the tonneau cover installed (if equipped). • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower [...]

If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground co[...]

2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter . 4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tight[...]

The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop[...]

7. If the fluid is low , add fluid in small amounts, continuously checking the level until it is between the MIN and MAX range. Refer to Maintenance Products Specifications and Capacities in this chapter for the proper fluid type. Be sure to put the cap back on the reservoir . BRAKE FLUID • V acuum boost system • Hydroboost system The fluid lev[...]

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to scheduled maintenance information for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir . Use only a DOT 3 brake fluid designed to meet Ford s[...]

1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. W ith the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage.[...]

High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correc[...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Us[...]

T RANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this[...]

AIR FILTER Refer to the scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter . The following procedure is for vehicles equipped with a gasoline engine. If your vehi[...]

5. Return air filter cover to original position making sure the four tabs are engaged and secure the three clamps. T ighten clamp on air tube and reconnect sensor . MOTORCRAFT PART NUMBERS Component 5.4L V8/6.8L V10 engines Air filter element F A-1883 Fuel filter FG-1083 Oil filter FL-820-S Battery (standard) BXT -65-650 Battery (optional) BXT -65-[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Front axle 5.8 pints (2.8L) Motorcraft SAE 80W -90 Premium Rear Axle Lubricant XY -80W -90–QL / WSP-M2C197–A Spindle bearing — High T emperature 4X4 Front Axle and Wheel Bearing Grease XG-11 / WSS-M1C267-A1 Rear axle - F-250/35[...]

Item Capacity Ford part name Ford part number / Ford specification Engine coolant (6.8L V10 engine) 2 26.7 quarts (25.3L) Motorcraft Premium Gold Engine Coolant (yellow-colored) VC-7-B / WSS-M97B51-A1 Engine and fuel coolant - diesel engine Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement Engine[...]

Item Capacity Ford part name Ford part number / Ford specification Fuel tank - Short box 30.0 gallons (113.4L) —— Fuel tank - Long box 38.0 gallons (143.9L) —— Fuel tank - Aft axle (Chassis cab only) 40.0 gallons (151.4L) —— Hinges, latches, striker plates, fuel filler door hinge and seat tracks — Multi-Purpose Grease XG–4 or XL-5 /[...]

Item Capacity Ford part name Ford part number / Ford specification Manual transmission fluid (M6HDW) - diesel engine Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement Automatic transmission fluid (5R110) 3 17.5 quarts (16.6L) 5 Motorcraft MERCON 威 LV AT F XT -10–QL V / MERCON 威 LV W indshie[...]

ENGINE DATA Engine 5.4L V8 engine 6.8L V10 engine Cubic inches 330 415 Required fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Spark plug gap 1.0–1.1mm (0.039–0.043 inch) 1.0–1.1mm (0.039–0.043 inch) Ignition system Coil on plug Coil on plug Compression ratio 9.8:1 9.2:1 Drivebelt routing 5.4L V8/6.8L V10 engines[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSIO[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Lifestyle Ash cup / smoker’ s package Bedliners and bedmats Cargo organization and management T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind Keyless entry keypad Remote start V ehicle security systems Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following[...]

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Components There [...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 401 2010 F-250/350/450/550 (f23) Owners Guide, 1st Printing USA (fus)[...]

A Accessory delay ........................ 126 Air cleaner filter ............... 388–389 Air conditioning ........................102 Airbag supplemental restraint system ........................................ 184 and child safety seats ............ 186 description .............................. 184 disposal ...................................[...]

safety belts .............................. 349 washing .................................... 344 waxing ..................................... 345 wheels ...................................... 345 wiper blades ............................ 347 Climate control (see Air conditioning or Heating) ....98, 102 Clock adjust 6-CD in dash ....................[...]

refill capacities ........................ 390 Event data recording .................... 8 Exhaust fumes .......................... 266 F Fail safe cooling ........................ 368 Family entertainment system .... 68 Fluid capacities ......................... 390 Fog lamps .................................. 107 Four -Wheel Drive vehicles ......[...]

Instrument panel cleaning ........................... 348–349 cluster ........................................ 14 lighting up panel and interior ..................................... 109 J Jump-starting your vehicle ......330 K Keyless entry system autolock ................................... 149 keypad ..................................... 157 l[...]

Power distribution box (see Fuses) ............................... 310 Power door locks ...................... 148 Power mirrors ........................... 127 Power point ...............................124 Power steering .......................... 271 fluid, checking and adding .... 381 fluid, refill capacity ................ 390 Power W indows .[...]

SYNC 威 .......................................... 97 T T ailgate ...................................... 143 T emperature control (see Climate control) ................. 98 T ilt steering wheel .................... 121 T ire Pressure Monitoring System (TPMS) T ires, Wheels and Loading .... 236 T ires ................................... 218–219 a[...]