Grizzly G0501 manuel d'utilisation

SLIDING TABLE SAW MODEL G0501 INSTRUCTION MANUAL COPYRIGHT © JULY, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #530903624 PRINTED IN USA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE [...]

WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr[...]

Table Of Contents SECTION 1: SAFETY ........................................................................................................................3 Safety Instructions for Power Tools ............................................................................................ 3 Additional Safety Instructions for Table Saws ...............[...]

SECTION 7: MAINTENANCE ........................................................................................................5 0 Cleaning ....................................................................................................................................50 Miscellaneous..............................................................[...]

G0501 Sliding Table Saw -3- 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 8. USE RIGHT TOOL. DO N[...]

-4- G0501 Sliding Table Saw 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your exte[...]

G0501 Sliding Table Saw -5- Additional Safety Instructions for Table Saws 7. USING THE RIP FENCE AND THE CROSSCUT FENCE TOGETHER DUR- ING A CUTTING OPERATION. When using the crosscut fence, the workpiece should never be contacting the rip fence while the saw blade is cutting. 8. STALLED BLADE. Turn the saw off before attempting to "free" [...]

-6- G0501 Sliding Table Saw Below are tips to reduce the likelihood of kick- back: • Never attempt freehand cuts. If the work- piece is not fed perfectly parallel with the blade, a kickback will likely occur. Always use the rip fence or crosscut fence to support the workpiece. • Make sure the riving knife is always aligned with the blade. A mis[...]

G0501 Sliding Table Saw -7- The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly! Arbor: Metal shaft extending from [...]

-8- G0501 Sliding Table Saw Grizzly Industrial, Inc. is proud to offer the Model G0501 Sliding Table Saw. This table saw is part of Grizzly’s growing family of fine woodworking machinery. When used according to the guide- lines stated in this manual, you can expect years of trouble-free, enjoyable operation, and proof of Grizzly’s commitment to[...]

G0501 Sliding Table Saw -9- A fire may occur if your particular electrical configuration does not comply with local and state codes. The best way to ensure compliance is to check with your local municipality or a licensed electrician. Your Shop Circuit Capacity Always check to see if the wires in your circuit are capable of handling the amperage dr[...]

-10- G0501 Sliding Table Saw A fire may occur if your particular electrical configuration does not comply with local and state codes. The best way to ensure compliance is to check with your local municipality or a licensed electrician. Your Shop Circuit Capacity Always check to see if the wires in your circuit are capable of handling the amperage d[...]

G0501 Sliding Table Saw -11- In the event of an electrical malfunction or break- down, grounding provides a path of least resis- tance for electric current to reduce the risk of electric shock. This machine must be equipped with an electric cord that has an equipment grounding conductor. This conductor must be grounded in accordance with all local [...]

-12- G0501 Sliding Table Saw The Model G0501 can be rewired for 440V oper- ation. This rewiring job consists of disconnecting the saw from the power source, changing the connections on the voltage transformer, changing the overload relays for the cutting motor and scoring motor, and rewiring the cutting motor and scoring motor. The necessary overlo[...]

G0501 Sliding Table Saw -13- 1. Flip Stops —Used for quick measurements for crosscutting. 2. Crosscut Fence —Used during crosscutting operations. Features a scale and multiple flip-style stopblocks for precise, repeatable crosscutting operations. 3. Crosscut Table —Provides a wide, stable platform for supporting full-size panels during crossc[...]

-14- G0501 Sliding Table Saw 9. Blade Guard —Fully-adjustable blade guard allows high visibility of the cutting operation while maintaining maximum protection around the saw blade. 10. Upper Dust Collection Port —2" port open- ing allows effective dust extraction from above the cutting operation. 11. Main Dust Collection Port —5" po[...]

G0501 Sliding Table Saw -15- Control Panel A. EMERGENCY STOP Button —Disconnects power to all motors in the motor cabinet. B. MAIN BLADE OFF Button —Stops the main saw blade. C. SCORING BLADE OFF Button —Stops the scoring blade. D. MAIN BLADE DOWN Key —Lowers the height of the main saw blade. E. SCORING BLADE RIGHT Key —Moves the scoring [...]

-16- G0501 Sliding Table Saw A. Fence Assembly Lock Down Lever — Secures the fence assembly into position along the fence rail. B. Micro-Adjust Knob —Precisely adjusts the fence. C. Forward/Backward Slide Lock Handle — Secures the aluminum fence piece on its for- ward/backward slide track. D. Micro-Adjust Lock Knob —Secures the fence after [...]

G0501 Sliding Table Saw -17- Main Crate: • Saw Base Unit • Blade Guard • Blade Guard Lower Support Arm • Blade Guard Upper Support Arm • Blade Guard Swing Arm • Push Stick • Large Extension Table • Large Extension Table Braces (2) • Small Extension Table • Small Extension Table Braces (2) • Crosscut Table • Riving Knife • [...]

-18- G0501 Sliding Table Saw Figure 11. Saw unit. Figure 12. Blade guard assembly. Figure 13. Extension tables and braces. Figure 14. Rip fence components and push stick. In the event that any non-proprietary parts are missing (e.g. nuts or washers), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at yo[...]

G0501 Sliding Table Saw -19- Figure 17. Sliding table. Figure 15. Crosscut fence components. Figure 16. Toolbox inventory.[...]

-20- G0501 Sliding Table Saw Hardware Recognition Chart[...]

G0501 Sliding Table Saw -21- 243.5" 193" (Fully Extended) Figure 18. Working clearances. Floor Load The Model G0501 weighs 2314 lbs. and has a base footprint of 64 1 ⁄ 2 " W x 39" D. Most commer- cial floors are suitable for your machine. Some residential floors may require additional reinforce- ment to support both the machin[...]

-22- G0501 Sliding Table Saw Moving & Placing Saw Base Unit To remove the saw base unit from the crate pallet: 1. Cut off and remove all plastic straps from the crate. 2. Position the forklift forks together and direct- ly above the saw. 3. Place two lifting straps over the forks and attach the ends to the lifting bolts as shown in Figure 19 . [...]

G0501 Sliding Table Saw -23- Table Installation The sliding table for the Model G0501 weighs over 350 lbs. Use at least four strong people to lift it in position. Improper lifting techniques or inadequate lifting assis- tance could result in serious crushing or strain injuries. Installing the sliding table is a difficult procedure because the slidi[...]

-24- G0501 Sliding Table Saw Figure 25. Three large caps screws to be removed from saw base unit. Figure 24. Blade tilt shipping brace. Figure 26. Parallel adjustment bolts. To install the sliding table: 1. Remove the red shipping brace, shown in Figure 24 , from the blade tilt mechanism. 3. Back out the parallel adjustment bolts shown in Figure 26[...]

G0501 Sliding Table Saw -25- Figure 27. Sliding table shipping brace. Figure 29. Sliding table handles. Figure 28. Access panel removed (one side shown). Figure 30. Sliding table end cap attachment screws. 8. Remove the shipping brace, shown in Figure 27 , from the end of the sliding table. 9. From the end of the sliding table, look inside the slid[...]

-26- G0501 Sliding Table Saw Installing Blade Guard The blade guard assembly consists of four pieces: Lower and upper support arms, a pivoting swing arm and a clear plastic blade guard shield. To install the blade guard: 1. Remove the six bolts from the side of the motor cabinet. 2. Position the lower support arm over the holes on the side of the m[...]

G0501 Sliding Table Saw -27- Installing Extension Tables To install the extension tables: 1. Assemble the braces to the underside of the small and large extension table, as shown in Figures 36 & 37 . Note— Do not fully tighten the braces to the tables. They will need to be adjusted during installation. Figure 34. Pivoting swing arm installed [...]

-28- G0501 Sliding Table Saw Figure 38. Hardware location for small table. Figure 39. Small extension table installed. Figure 40. Checking with a straight edge. 4. Use the adjustment screws ( Figure 39 ) under the extension table to level the top sur- face with the saw table. 5. When the surfaces are level, slide the table supports against the mach[...]

G0501 Sliding Table Saw -29- 6. Slide one end of the aluminum fence piece over the mounting track on the side of the fence clamping assembly. Note— The alu- minum fence piece should slide smoothly back and forth. The handle on the top of the clamping assembly rotates to lock the alu- minum fence piece into position ( Figure 44 ). Figure 44. Insta[...]

-30- G0501 Sliding Table Saw Figure 45. Installed clamp assembly. 7. Check if the bottom edge of the aluminum fence piece rests on the top surface of the table. Note— The aluminum fence piece will scratch the table surface if the ride height is not adjusted correctly. — If the bottom edge of the aluminum fence piece does not rest on the table, [...]

G0501 Sliding Table Saw -31- Figure 47. Mounting the crosscut table over the shaft on the brace. Figure 48. Cross-support assemblies. Figure 49. Cam lock rod (1 of 2). 5. Remove both end caps from the short cross- support and remove one end cap from the long cross-support as shown in Figure 48 . 9. Using the handles on the crosscut fence, slide the[...]

-32- G0501 Sliding Table Saw Miter Fence To install the miter fence: 1. Loosen the clamp plate with the ratchet han- dle to prepare the miter fence for installation. 2. Align the fixed bolt in the slot closest to the blade and align the clamp plate in the other slot as shown in Figure 51 . Figure 51. Miter fence components aligned for installation [...]

G0501 Sliding Table Saw -33- Test Run Now that the machine is connected to the power source, it is important to perform a test run to make sure all the controls are working properly. Before starting the saw, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are fami[...]

-34- G0501 Sliding Table Saw Figure 55. Sliding table parallel adjustment bolt (other side not shown). 9. Repeat steps 5–6 until the gap between your mark on the blade and the edge of the sliding table is even at both ends. 10. Tighten the jam nuts on the parallel adjust- ment bolts to secure them in place 11. Now tighten the three large cap scre[...]

G0501 Sliding Table Saw -35- Fence Scale Alignment Before operation, the 0" mark on the rip fence scale must be aligned with the right side of the blade to ensure that the rip fence measurements will be accurate. To align the fence scale with the blade: 1. Set the blade to 0˚ on the control panel (90˚ with the cast iron table). 2. Raise the [...]

-36- G0501 Sliding Table Saw NOTICE Remember maximum working clearances when installing dust hoses. Dust Collection The Model G0501 is equipped with two dust ports that should be properly connected to a dust col- lection system before operation. To connect the dust ports to a dust collection system: 1. Secure a 5" dust hose to the dust port lo[...]

G0501 Sliding Table Saw -37- NOTICE The following section was designed to give instructions on the basic operations of this machine. However, it is in no way compre- hensive of all of the machine’s applications. WE STRONGLY RECOMMEND that you read books, trade magazines, or get formal train- ing to maximize the potential of your machine. Damage t[...]

-38- G0501 Sliding Table Saw The blades for the Model G0501 can operate at 3000, 4000, 5000, and 6000 RPM. This speed can be easily changed by moving the V-belt posi- tion on the main motor pulley and arbor pulley. To change the blade speed: 1. Disconnect the saw from the power source! 2. Remove the cap screws on the top and bot- tom right corners,[...]

G0501 Sliding Table Saw -39- 3000 4000 6000 5000 5. Turn the pulley speed switch ( Figure 63 ) so that the opening in the fins line up with the belt position. This switch registers the speed with the control panel. Figure 62. Belt speed diagram. Figure 64. Fence against blade as a guide for aligning the scoring blade. Figure 63. Pulley speed switch[...]

-40- G0501 Sliding Table Saw The Model G0501 has the capability of rip cutting full size panels ( Figure 65 ). The sliding table removes the burden of sliding a large and heavy panel over a stationary table surface. This saw also has the capability of rip cutting smaller boards, using the machine as a tradition- al table saw ( Figure 66 ). Smaller,[...]

G0501 Sliding Table Saw -41- 5. Position the blade guard to the correct height for your workpiece. 6. Load the workpiece onto the table saw. The set up should look similar to Figure 65 . 7. Once all the necessary safety precautions have been taken, perform the cutting opera- tion. Rip cutting using the traditional table saw technique: 1. Slide the [...]

-42- G0501 Sliding Table Saw Figure 71. Crosscutting workpieces using the rip fence as a cut-off gauge. Lastly, this machine has the capability of cross- cutting workpieces while using the rip fence as a cut-off gauge ( Figure 71 ). Determine which cutting operation will be best suited for the workpiece to be crosscut. — If you will be crosscutti[...]

G0501 Sliding Table Saw -43- Crosscutting full size panels: 1. Mount the crosscut table to the sliding table. 2. Install the crosscut fence in the forward guide pin holes shown in Figure 72 and lock it in place. Note— First, drop the crosscut fence into the outside edge guide pin hole, then drop the other end of the crosscut fence into the guide [...]

-44- G0501 Sliding Table Saw Figure 73. Correct rip fence position when per- forming crosscutting operations. 6. Position the blade guard to the correct height for your workpiece. 7. Once all the necessary safety precautions have been taken, perform the cutting opera- tion. Figure 74. Example of miter cutting operation for a cut length less than 45[...]

G0501 Sliding Table Saw -45- Figure 77. Flip stop slide lock knobs. 3. Loosen the lock knobs that secure the flip stop slide into position in the miter fence ( Figure 77 ). To perform a miter cut: 1. Mount the miter fence onto the sliding table. 2. Position the fence at the desired angle and use the clamp plate ratcheting handle to lock the fence i[...]

-46- G0501 Sliding Table Saw 5. Position the blade guard to the correct height for your workpiece. 6. Load the workpiece onto the table saw. The set up should look similar to Figure 74 or 75 . 7. Once all the necessary safety precautions have been taken, perform the cutting opera- tion. The Model G0501 will perform best when high quality, sharp bla[...]

G0501 Sliding Table Saw -47- The Model G0501 comes with a riving knives for use with 12" and 14" blades. To change the riving knife: 1. Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade as far as it will go. 2. Disconnect the saw from the power source! 3. Move the sliding table all the way to [...]

-48- G0501 Sliding Table Saw Figure 86. Scoring blade set separated for identification. The scoring blade set consists of an inner and outer blade and four internal shims. Two of these shims are 0.008" thick and two are 0.004". These have been provided so the scoring blade set can match the kerf thickness of the main blade. Figure 86 show[...]

G0501 Sliding Table Saw -49- 4. Pull the blade guard away from the blades to expose the arbor nut as shown in Figure 88 . (The internal blade guard is held in place with a magnet.) 5. Remove the main blade. Figure 89. Loosening scoring blade arbor nut. Figure 88. Scoring blade arbor nut. 6. Place a 23mm wrench behind the scoring blade on the flats [...]

-50- G0501 Sliding Table Saw To ensure optimum power transmission from the motor to the blade and to the hydraulic pump, the V-belts must be in good condition (free from cracks, fraying and wear) and operate under proper tension. Check the V-belts at least every 3 months; more often if the saw is used daily. See Section 8: Service Adjustments for i[...]

G0501 Sliding Table Saw -51- Maintenance Performed Approximate Hours Of Use Maintenance Log Date[...]

-52- G0501 Sliding Table Saw Always disconnect power to the machine before performing ser- vice adjustments. Failure to do this may result in serious personal injury. To change the V-belt on the main motor: 1. Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade and scoring blade set up as far as they will[...]

G0501 Sliding Table Saw -53- To change the belt on the scoring blade motor: 1. Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade and scoring blade set up as far as they will go. 2. Disconnect the saw from the power source! 3. Open the motor cabinet door. 4. Jack up the scoring blade motor with a bottle [...]

-54- G0501 Sliding Table Saw The riving knife can be aligned with the blade by adjusting the four setscrews on the mounting plate. To align the riving knife: 1. Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade and scoring blade set up as far as they will go. 2. Disconnect the saw from the power source![...]

G0501 Sliding Table Saw -55- Squaring the crosscut fence to the blade ensures that cuts made with the crosscut fence will be square. This procedure can be done by using a piece of scrap plywood as a test piece and mak- ing five test cuts, then adjusting the fence as nec- essary. To square the crosscut fence with the blade: 1. Make sure the blade is[...]

G0501 Sliding Table Saw -57- Replacement Blades 80 Tooth Carbide Tipped 14" Blade ..........H3388 100 Tooth Carbide Tipped 14" Blade ........H3389 The following pages contain aftermarket acces- sories information, the machine data sheet, parts diagrams, parts lists, wiring diagrams, troubleshoot- ing information and Warranty/Return inform[...]

-58- G0501 Sliding Table Saw Design Type .................................................................................................... Floor Model Overall Dimensions: Overall Width ....................................................110" (218" w/Sliding Table Extended) Overall Depth .................................................[...]

G0501 Sliding Table Saw -59- Scoring Motor: Arbor ..........................................................................................................22mm & 3 ⁄ 4 " Arbor Speed ..................................................................................................8000 RPM Horsepower.......................................[...]

MODEL G0501 14" SLIDING T ABLE SA W Customer Ser vice #: (5 70) 546 -9 663 • T o Order Call : (8 00) 523- 4 777 • F a x #: (80 0) 438 -59 0 1 SL ID ING T A BL E S A W C AP A CI T IES Ripping Width Miter Cut 90º (push cut) Miter Cut 45º Miter Cut 45º (push cut) Cross Cut (fence not extended) Miter Cut 45º (push cut, fence not extended) [...]

-60- G0501 Sliding Table Saw 101 103 104 105 102 109 103 102 108 103 102 107 106 110 111 112 114 115 116 117 118 121 113 120 119 122 123 124 110 125 126 128 105 127 112 129 141 150 149 148 147 144 146 145 142 143 151 G0501 Machine Frame Assembly[...]

G0501 Sliding Table Saw -61- REF PART # DESCRIPTION REF PART # DESCRIPTION 126 PLW06M LOCK WASHER 10MM 127 P05010027 U-PROFILE 128 PB01M HEX BOLT M10-1.5 x 30 129 PLW02M LOCK WASHER 4MM 131 P05010031 GEAR 132 PSS02M SET SCREW M6-1.0 X 6 133 PSB23M CAP SCREW M4-.7 X 12 134 P05010034 BASE PLATE 135 PW03M FLAT WASHER 6MM 136 PLW03M LOCK WASHER 6MM 137[...]

-62- G0501 Sliding Table Saw 203 206 204 205 202 201 205 204 207 209 210 208 211 204 205 212 209 208 210 214 213 215 237 236 218 217 219 220 216 221 222 204 223 225 216 226 227 229 204 210 208 209 230 205 211 204 232 231 233 228 205 224 235 234 204 205 205 222 204 217 239 238 240 241 243 242 G0501 Chip Channel Assembly[...]

G0501 Sliding Table Saw -63- REF PART # DESCRIPTION REF PART # DESCRIPTION 223 P05010223 STOP 224 PLW05M LOCK WASHER 12MM 225 PSB92M CAP SCREW M12-1.75 X 40 226 P05010226 ARC GEAR 227 P05010227 STRAIGHT PIN M8 X 30 228 P05010228 SEGMENT 229 PB15M HEX BOLT M8-1.25 X 40 230 P05010230 SWIVEL LEVER 231 P05010231 CLAMPING PIN 10MM 232 PLW06M LOCK WASHER[...]

-64- G0501 Sliding Table Saw 315 316 314 321 323 324 322 317 316 304 304 309 318 320 319 304 313 304 313 312 305 304 311 310 309 307 308 303 302 301 304 305 306 G0501 Saw Blade Adjustment Assembly[...]

G0501 Sliding Table Saw -65- REF PART # DESCRIPTION REF PART # DESCRIPTION 313 P05010313 CLEVIS BOLT M12-1.75 314 P05010314 GROOVED CLEVIS PIN 315 P05010315 SPECIAL HEX SCREW 316 P05010316 BUSHING 317 PN09M HEX NUT M12-1.75 318 P05010318 LINEAR ACTUATOR 319 PSS02M SET SCREW M6-1.0 X 6 320 PR03M EXT RETAINING RING 12MM 321 PSB31M CAP SCREW M8-1.25 X[...]

-66- G0501 Sliding Table Saw 401 408 404 402 406 405 410 402 409 403 407 411 412 413 416 414 415 417 418 419 420 421 427 428 429 402 410 422 425 426 425 424 423 449 448 446 447 446 425 430 431 432 433 434 435 436 437 402 401 438 439 412 441 440 442 436 435 444 410 425 402 410 443 451 450 452 453 454 455 456 457 458 459 460 461 463 462 412 468 469 4[...]

G0501 Sliding Table Saw -67- REF PART # DESCRIPTION REF PART # DESCRIPTION 447 P05010447 EYE BOLT 448 PN02M HEX NUT M10-1.5 449 PN09M HEX NUT M12-1.75 450 PB101M HEX BOLT M12-1.75 X 40 451 PLW05M LOCK WASHER 12MM 452 PW06M FLAT WASHER 12MM 453 P05010453 RIVING KNIFE 14" 453A P05010453A RIVING KNIFE 12" 454 P05010454 STUD BOLT 455 P0501045[...]

-68- G0501 Sliding Table Saw G0501 Scoring Saw Assemblies 501 502 503 504 505 506 507 508 509 510 511 509 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 563 528 529 530 529 528 563 531 532 531 562 535 534 533 550 551 550 553 554 555 552 556 557 557 558 559 522 521 520 553 533 534 560 519 561 560 534 533 549 542 543 536 537 538 539 [...]

G0501 Sliding Table Saw -69- G0501 Scoring Saw Assemblies REF PART # DESCRIPTION REF PART # DESCRIPTION 532 PSS19M SET SCREW M8-1.25 X 30 533 PN09M HEX NUT M12-1.75 534 PLW05M LOCK WASHER 12MM 535 PSS70M SET SCREW M12-1.75 X 80 536 PSB06M CAP SCREW M6-1.0 X 25 537 PLW03M LOCK WASHER 6MM 538 PW03M FLAT WASHER 6MM 539 P05010539 BELT GG04-16RF-850 540[...]

-70- G0501 Sliding Table Saw G0501 Swinging Arm Assembly 608 610 611 609 608 607 603 602 603 605 606 604 602 624 628 625 626 627 626 622 625 623 622 619 616 618 617 621 620 608 614 613 615 612 608 613 601 629[...]

G0501 Sliding Table Saw -71- G0501 Swinging Arm Assembly REF PART # DESCRIPTION REF PART # DESCRIPTION 616 PLW04M LOCK WASHER 8MM 617 PW01M FLAT WASHER 8MM 618 PR37M EXT RETAINING RING 32MM 619 P6002 BALL BEARING 6002 620 P05010620 PLASTIC ROLLER 621 P05010621 CAM 622 PW01M FLAT WASHER 8MM 623 PB20M HEX BOLT M8-1.25 X 35 624 PB09M HEX BOLT M8-1.25 [...]

",'" <%*%& Ha^Y^cIVWaZ HVl ' 3LIDING 4ABLE AND -ITER &ENCE !SSEMBLIES ,%& ,%' ,%* ,%) ,%( ,%, ,,+ ,&- ,&, ,&% ,%+ ,&+ ,&* ,&) ,&( ,&' ,%( ,%& ,%+ ,&& ,%( ,%- ,&& ,%* ,%) ,)- ,*. ,+% ,%& ,)- ,*- ,*, ,** ,*+ ,*)[...]

<%*%& Ha^Y^cIVWaZ HVl ",(" ' 3LIDING 4ABLE AND -ITER &ENCE !SSEMBLIES 2%& 0!24  $%3#2)04)/. 2%& 0!24  $%3#2)04)/. ,)& E%*%&%,)& ;>M:9E>:8: ,)' E%*%&%,)' HIDE ,)( EH7&&B 86E H8G:LB-"[...]

-74- G0501 Sliding Table Saw G0501 Crosscut Table 805 803 804 809 808 802 801 806 807 811 810 812 816 815 814 813 817 814 816 815 819 818 817 821 832 836 835 834 833 841 827 826 825 818 828 830 831 818 827 830 829 828 826 825 824 822 823 818 811 839 837 838 840 821 820 818 819 818[...]

G0501 Sliding Table Saw -75- G0501 Crosscut Table REF PART # DESCRIPTION REF PART # DESCRIPTION 822 PB74M HEX BOLT M10-1.5 X 20 823 P05010823 CROSS SLIDE SUPPORT 824 P05010824 RUBBER GUIDE 825 PB07M HEX BOLT M8-1.25 X 25 826 PLW04M LOCK WASHER 8MM 827 P05010827 EYE BOLT 828 P05010828 SPACER 829 P05010829 AXIS FOR ROLLER 830 P6001 BALL BEARING 6001 [...]

-76- G0501 Sliding Table Saw G0501 Crosscut Fence 994 993 992 991 993 994 992 991 907 906 908 909 911 910 905 913 912 914 915 917 916 918 919 920 921 922 923 922 921 918 919 917 916 920 924 925 926 927 931 930 929 928 932 933 934 930 912 935 906 911 936 937 904 903 902 901 938 939 908 941 936 940 942 911[...]

G0501 Sliding Table Saw -77- G0501 Crosscut Fence REF PART # DESCRIPTION REF PART # DESCRIPTION 922 P05010922 ROUND KNOB (FEM) 3/8-16 923 P05010923 KNOB BOLT M6-1 X 75 924 P05010924 SUPPORT 925 P05010925 PULL NAIL 926 P05010926 FIXED PIN 927 PFH12M FLAT HD SCR M6-1.0 X 25 928 P05010928 PLATE 929 PB02M HEX BOLT M6-1.0 X 12 930 PHTEK24 TAP SCREW 1/8&[...]

-78- G0501 Sliding Table Saw G0501 Machine Table Assemblies 1001 1002 1014 1015 1011 1012 1012 1011 1013 1004 1003 1005 1006 1006 1004 1007 1008 1010 1009 1021 1022 1007 1020 1019 1016 1017 1018 1016 1017 1018 1023 1015 1024 1031 1033 1034 1032 1042 1035 1040 1039 1037 1038 1036 1041 1037 1038 1039[...]

G0501 Sliding Table Saw -79- G0501 Machine Table Assemblies REF PART # DESCRIPTION REF PART # DESCRIPTION 1019 PSB06M CAP SCREW M6-1.0 X 25 1020 P05011020 TABLE BRACE 1021 PN03M HEX NUT M8-1.25 1022 PSB31M CAP SCREW M8-1.25 X 25 1023 PLW04M LOCK WASHER 8MM 1024 PW01M FLAT WASHER 8MM 1031 P05011031 WIDTH EXTENSION TABLE 1032 PSB06M CAP SCREW M6-1.0 [...]

-80- G0501 Sliding Table Saw G0501 Rip Fence Assembly 1101 1102 1103 1104 1105 1106 1107 1108 1109 1111 1110 1112 1113 1126 1141 1127 1128 1114 1115 1116 1117 1119 1120 1122 1120 1121 1123 1125 1124 1115 1114 1131 1130 1129 1112 1111 1133 1135 1134 1132 1140 1118 1118 1119 1139 1138 1137 1136[...]

G0501 Sliding Table Saw -81- G0501 Rip Fence Assembly REF PART # DESCRIPTION REF PART # DESCRIPTION 1122 P05011122 GRIP 1123 PSS05M SET SCREW M5-.8 X 10 1124 P05011124 STEEL BALL 1125 P05011125 HELICAL PRESSURE SPRING 1126 PSS69M SET SCREW M20-2.5 X 120 1127 PN28M HEX NUT M20-2.5 1128 P05011128 ROUND BAR 1129 P05011129 CAM 1130 P05011130 ROLLER 113[...]

-82- G0501 Sliding Table Saw G0501 Blade Guard Assembly 1204 1205 1206 1202 1201 1209 1208 1210 1205 1203 1207 1203 1208 1209 1210 1211 1203 1202 1202 1212 1213 1216 1218 1219 1221 1222 1224 1223 1209 1225 1210 1265 1263 1264 1262 1261 1260 1228 1259 1257 1258 1256 1228 1226 1224 1255 1209 1225 1210 1202 1241 1242 1229 1230 1243 1229 1230 1245 1247[...]

G0501 Sliding Table Saw -83- G0501 Blade Guard Assembly REF PART # DESCRIPTION REF PART # DESCRIPTION 1243 PR09M EXT RETAINING RING 20MM 1244 P05011244 LEVER STUD 1245 P05011245 SPECIAL KNOB BOLT 1246 P05011246 CONNECTING ARM 1247 PB03M HEX BOLT M8-1.25 X 16 1248 P05011248 WIRE FIXED BLOCK 1249 P05011249 ROD 1250 PSB01M CAP SCREW M6-1 X 16 1251 PN0[...]

-84- G0501 Sliding Table Saw G0501 Electrical Panel Components 1320 1301 1304 1302 1303 1306 1305 1305 1304 1308 1307 1307 1309 1310 1311 1312 1313 1314 1316 1315 1317 1309 1309 1309 1309 1309 1309 1309 1309 1310 1310 1310 1319 1318[...]

G0501 Sliding Table Saw -85- G0501 Electrical Panel Components REF PART # DESCRIPTION REF PART # DESCRIPTION 1312 P05011312 FUSE 3A 1313 P05011313 TRANSFORMER SP-TBS,1PH, 220V 1314 P05011314 MAG CONTACTOR CN-25 1315 P05011315 OVR-RELAY RH 18/26 1316 P05011316 OVR-RELAY RH 10E/3C 1317 P05011317 POWER SELECTOR SWITCH 220V 1318 P05011318 TERMINAL STRI[...]

-86- G0501 Sliding Table Saw Motor Troubleshooting Motor will not start. 1. Low voltage. 1. Check power line for proper voltage. 2. Open circuit in motor or loose 2. Inspect all lead connections on motor for loose or open connections. connections. Motor will not start; fuses or circuit 1. Short circuit in line cord or plug. 1. Repair or replace cor[...]

G0501 Sliding Table Saw -87- Performance Troubleshooting Rip fence scratches table . Cuts made on the sliding table are not square. Cuts made with the crosscut fence are not square. Cuts made with the rip fence are not square. The rip fence scale is not accurate. The scoring blade cannot be aligned with both the left and right edges of the main bla[...]

-88- G0501 Sliding Table Saw 01 04 02 03 06 05 05 04 1 2 3 4 5 6 7 8 9 10 11 20 19 18 17 16 15 13 14 12 21 22 25 40 4 6 6 43 41 2 5 5 41 40 10Hp Main Motor Y1 Z1 X1 U1 V1 W1 V2 U2 W2 X2 Z2 Y2 U1 V1 W1 X2 Z2 Y2 X1 U2 W2 Z1 V2 Y1 LOWER VOLTAGE (220V) LOWER VOLTAGE (220V) VOLTAGE (440V) HIGHER VOLTAGE (440V) HIGHER 1Hp Scoring Motor 8 2 5 1 7 4 3 9 6 [...]

G0501 Sliding Table Saw -89- 08 07 07 09 09 09 09 10 10 10 10 11 12 13 14 09 09 09 09 09 16 15 17 - + G3 2 21 20 2 22 22 19 25 23 20 26 24 24 26 CN-11 CN-11 CN-11 CN-11 M5a M5b M6a M6b 27 2 8 9 11 28 2 12 14 29 2 15 18 17 2 30 R1 R2 R4 R3 220V 0V PT 0V OUT-PUT 440V IN-PUT 380V 415V + - +H -H +L -L 42 2 +H -H +L -L 1 R 2 S - 24V,Red 0V,Red + 400V 10[...]

-90- G0501 Sliding Table Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written [...]

CUT ALONG DOTTED LINE ___Other__________________________________________________ 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10"[...]

TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend:[...]

[...]

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website Today And Discover Why Grizzly ® Is The Industry Leader! Call Today For A FREE Full Color Catalog[...]