Français dropdown-ico

Henny Penny OFE/OFG-324 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Henny Penny OFE/OFG-324. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Henny Penny OFE/OFG-324 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Henny Penny OFE/OFG-324 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Henny Penny OFE/OFG-324 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Henny Penny OFE/OFG-324
- nom du fabricant et année de fabrication Henny Penny OFE/OFG-324
- instructions d'utilisation, de réglage et d’entretien de l'équipement Henny Penny OFE/OFG-324
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Henny Penny OFE/OFG-324 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Henny Penny OFE/OFG-324 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Henny Penny en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Henny Penny OFE/OFG-324, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Henny Penny OFE/OFG-324, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Henny Penny OFE/OFG-324. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Model OFE/OFG-321,322,323,324 SECTION 2. MAINTENANCE 2-1. INTRODUCTION This section provides procedures for the checkout and replacement of the various parts used within the fryer. Before replacing any parts, refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. You may need to [...]

  • Page 2

    Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 3. Remove the two nuts securing the high limit bracket to the unit and pull the bracket from the unit. 4. Remove the two screws securing the high limit to the bracket, and remove the high limit from the bracket. 5. Remove the two electrical wires from the high tem perature[...]

  • Page 3

    Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 5. Remove the bracket from the heat tube covering the high lim it bulb. 6. Straighten the capillary tube behind the pot wall. 7. Pull the high limit bulb through the retainers on the heat tube. 8. Remove the larger outside nut that threads into the pot wall. 9. Remove the [...]

  • Page 4

    Model OFE/OFG-321,322,323,324 2-4. COMPLETE CONTROL PANEL REPLACEMENT Should the control board become inoperative, follow these instructions for replacing the board. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall [...]

  • Page 5

    Model OFE/OFG-321,322,323,324 2-5. POWER SWITCH (Continued) 4. With control panel removed, and the wires off the switch, push in on tabs on the switch to remove from panel. 5. Replace with new switch, and reconnect wires to switch. 6. Replace the control panel. 2-6. TEMPERATURE PROBE The temperature probe relays the actual shortening tem perature t[...]

  • Page 6

    Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE REPLACEMENT (Continued) ELECTRIC GAS 2-6 606[...]

  • Page 7

    Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE 7. Tighten the compression nut hand tight and then a half turn REPLACEMENT with wrench. (Continued) Excess force will damage temperature probe. 8. Connect new temperature probe to PC board and replace control panel. 9. Replace shortening. 10. Turn power on and check out fryer. 606 2-7[...]

  • Page 8

    Model OFE/OFG-321,322,323,324 2-7. FLAME SENSOR The flame sensor recognizes the pilot flame and allows gas to (Gas Units) continue to the pilot. The flame sensor must send a m inimum of two (2) micro amps to the ignition m odule. The pilot flame should be split in two by the flame sensor, causing the flam e sensor to be bright red in color. 1. Remo[...]

  • Page 9

    Model OFE/OFG-321,322,323,324 2-8. PILOT / IGNITOR The Henny Penny open fryer (gas) has electronic spark ignition ASSEMBLY that lights a standing pilot. The gap between the spark electrode and the pilot hood should be set at 1/8 of an inch. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER[...]

  • Page 10

    Model OFE/OFG-321,322,323,324 2-9. IGNITOR MODULE During normal operation, the ignition modules send 24 volts to the ignitors and gas control valve. If a module does not sense a pilot flame, the module starts the ignition process again. But, if a pilot light goes out for longer that 10 seconds, or it goes out 3 times within 10 seconds, the module k[...]

  • Page 11

    Model OFE/OFG-321,322,323,324 2-11. I/O POWER SUPPLY BOARD ASSEMBLY The input/output power supply board assembly distributes voltage to the various components in the fryer. The board also receives information from com ponents in the fryer. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER [...]

  • Page 12

    Model OFE/OFG-321,322,323,324 2-12. VACUUM SWITCH (Continued) 5. Using a Phillips head screwdriver, remove the screws securing the vacuum switch to the shroud. 6. Install the new vacuum switch in reverse order. To avoid property damage, do not tamper with, or disas- semble this component. It is set and sealed from the factory and is not to be adjus[...]

  • Page 13

    Model OFE/OFG-321,322,323,324 2-14. DRAIN MICROSWITCH Upon turning the drain handle, the drain microswitch circuit should open, cutting off the pilot flame. This will prevent the fryer from heating while shortening is being drained from the frypot. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move t[...]

  • Page 14

    Model OFE/OFG-321,322,323,324 2-15. FILTER SWITCH (Continued) 2. Remove the control panel above the switch. 3. Label and remove the wires from the switch. W ith test instrument, check across the terminals of the switch with the switch in the ON position, and then in the OFF position. With the switch in the ON position, the circuit should be closed.[...]

  • Page 15

    Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 3. Using a 7/16 inch wrench, remove the pilot line from the gas control valve. 4. Using a 1 inch wrench, loosen the nut securing the main gas inlet line to the gas control valve. 5. Using 5/8 inch wrench, remove the two burner gas line fittings at the black tee fitting, loca[...]

  • Page 16

    Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 7. With the bracket dropped down, remove the two screws behind the bracket securing the gas control valve to the bracket. 8. Install the new gas control valve in reverse order. 2-17. BLOWER MOTOR ASSEMBLY The blower motor assembly induces the draft for the burners. If the bl[...]

  • Page 17

    Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 4. Remove wire nuts connecting blower motor wires to wires in conduit. 5. Loosen conduit from blower motor. 6. Remove screws connecting flue to bracket in upper frame. 7. Remove screws connecting flue to blower. 203 2-17[...]

  • Page 18

    Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 8. Using 3/8 inch nut driver, remove nuts securing blower to the unit. Pull blower from unit. 9. Install new blower in reverse order. 2-18. HEATING ELEMENTS (ELECTRIC ONLY) Heating elements are available for 208 and 230 volts. Check data plate to determine correct voltage. C h e [...]

  • Page 19

    Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 3. Perform an ohm check on one element at a tim e, with wires disconnected from element. If the resistance is not within tolerance, replace the element. Voltage Wattage Resistance Ohms (cold) 208 4800 9 230 4800 11 Replacement: Refer to figure 2-2. 1. Drain the shorten[...]

  • Page 20

    Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 9. Evenly space the element spreaders on the sides of the elements and reinstall bolts. Place the fifth spreader in the front of the elements as to protect the temperature probe. (Fig.6-1 10. Replace the high limit bulb holder on the top element, and position the bulb [...]

  • Page 21

    Model OFE/OFG-321,322,323,324 2-19. HEATING CONTACTORS (ELECTRIC ONLY) Each well of an electric fryer requires two switching contactors. The first in line is the primary contactor and the second in line is the heat contactor. When open, the primary contactor does not allow power to flow to the heat contactor. When closed, the primary supplies volta[...]

  • Page 22

    Model OFE/OFG-321,322,323,324 2-19. HEATING Checkout (Power Supplied) CONTACTORS (ELECTRIC ONLY) (Continued) To avoid electrical shock, make connections before applying power, take reading, and remove power before removing meter leads. The following checks are performed with the wall circuit breaker closed and the main power switch in the ON positi[...]

  • Page 23

    Model OFE/OFG-321,322,323,324 2-20. SPEAKER ASSEMBLY (Electric Units) The speaker assembly emits audible signals to let the operator know when cooking and hold times are finished. 1. Remove electrical power supplied to unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cor[...]

  • Page 24

    Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE 1. Drain the shortening from the frypot. LIMIT CONTROL (Electric Units) (Continued) 2. Remove control panel. 3. Loosen small inside screw nut on capillary tube. 4. Remove capillary bulb from bulb holder inside the frypot. 5. Straighten the capillary tube. 6. Remove larger outside nut that threads[...]

  • Page 25

    Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE LIMIT CONTROL (Electric Units) (Continued) Be sure capillary bulb of high limit is located behind capillary bulb of thermostat. Both capillary bulbs and bulb holders should be positioned as not to interfere with basket or when cleaning the frypot wall, or damage to capillary tube could result. 13[...]

  • Page 26

    Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 5. Disconnect actuator connector and cut the wires from the other half of the connector, as shown at left. The new actuator wires do not have a connector on them and must be connected directly to the wires on the unit. 6. Using a 3/8 socket, remove[...]

  • Page 27

    Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 9. Remove the 2 front mounting screws from the actuator support plate. 10. Remove all the top screws, securing all the actuator support plates to the back shroud, to help loosen the back shroud. 11. Remove all remaining back shroud screws to loosen[...]

  • Page 28

    Model OFE/OFG-321,322,323,324 2-23. AUTOLIFT 1. Remove electrical power supplied to unit. TRANSFORMER REPLACEMENT (if applicable) To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove control panel. 3. Label and remove wires from transform er. 4. [...]

  • Page 29

    Model OFE/OFG-321,322,323,324 2-24. AUTOLIFT PC BOARD REPLACEMENT (if applicable) (Continued) 4. Using a Phillips-head screwdriver, remove the 2 screws securing the autolift PC board bracket to the frame and remove bracket from unit. (The right screw needs removed to disconnect the ground wire, but the left screw can be loosened and the bracket sli[...]