HP (Hewlett-Packard) 6120 manuel d'utilisation

Augu st 2 0 09 Pr oC ur v e Ser i es 6 1 20 S w itc he s Ma na ge ment a nd C on figu ration Gu id e[...]

Hewlett-Packa rd Company 8000 Foothills Boulevard, m/s 5551 Roseville, California 95747-5551 http://www .procurve.com © Copyright 2009 Hewlett-Pa ckard Development Company, L.P . The infor mation contained herein is subjec t to change with- out notice. All Ri ghts Reserved. This document contains proprie tary information, which is protected by cop[...]

ii[...]

iii Contents Product Documentation About Your Switch Manual Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi Printed Publications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi Electronic Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi Software Fea[...]

iv Understanding Physical Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Understanding Management I nterfaces . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Advantages of Using the Menu Interface . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Advantages of Using the CLI . . . . . . . . . . . . . . . . . . . . .[...]

v Accessing the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Privilege Levels at Logon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Privilege Level [...]

vi Online Help for the Web Browser Interface . . . . . . . . . . . . . . . . . . . . 5-11 Support/Mgmt URLs Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Support URL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 Help and the Management Server URL . . . . . . . . .[...]

vii Setting the Default Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21 Booting from the Defau lt Flash (Prima ry or Secondary) . . . . . . 6-22 Booting from a Specified Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 Using Reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

viii Interface Access: Console/Serial Link, Web, and Inbound Telnet . 7-3 Menu: Modifying the Interface Access . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 CLI: Modifying th e Interface Ac cess . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Denying Interface Access by Te rminating Remote Management Sessions . . . . . . . . .[...]

ix General Steps fo r Running a T ime Protocol on the Switch: . . . . . . . . 9-3 Disabling Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 SNTP: Viewing, Selecting, a nd Configuring . . . . . . . . . . . . . . . . . . . . . 9-4 Menu: Viewing and Co nfiguring SNTP . . . . . . . . . . . . . . . . . . . . . . . [...]

x Configuring a Bro adcast Limi t on the Switch . . . . . . . . . . . . . . . . . . 10-18 Configuring ProCurve Auto-MDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-19 Web: Viewing Port Status and Co nfiguring Port Parameters . . . . . 10-22 Using Friendly (Optional) Port Names . . . . . . . . . . . . . . . . . . . . . . . 10-23 Config[...]

xi Default Port Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21 LACP Notes and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-22 Trunk Group Operation Usin g the “Trunk” Option . . . . . . . . . . . . 11-26 How the Switch Lists Trunk Data . . . . . . . . . . . . . . . . . [...]

xii Group Access Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12 SNMPv3 Communities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12 Menu: Viewing and Co nfiguring no n-SNMP version 3 Communities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14 CLI:[...]

xiii LLDP-MED To pology Ch ange Notification . . . . . . . . . . . . . . . . . 13-58 LLDP-MED Fast Start Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-60 Advertising Device Capability, Network Policy, PoE Status and Location Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-60 Configuring Locat ion[...]

xiv CLI: Xmodem Download from a PC or UNIX Workstation to Primary or Secondary Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21 Switch-to-Switch Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-22 Menu: Switch-t o-Switch Download to Primary Flash . . . . . . . . A-22 CLI: Switch-To-Switc h Downloads . .[...]

xv Menu Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8 CLI Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 Port Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 Menu: Displaying Port Status [...]

xvi Traffic Select ion Option s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-36 Mirroring-Sourc e Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . B-36 Selecting All Inbound/Outbound Traffic to Mirror . . . . . . . . . . . . . . B-36 Displaying a Mirroring Configurat ion . . . . . . . . . . . . . . . . . . . . .[...]

xvii Event Log Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-24 Menu: Displaying and Navigating in the Ev ent Log . . . . . . . . . . . . . C-31 CLI: Displaying the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-32 CLI: Clearing Event Log Entries . . . . . . . . . . . . . . . [...]

xviii Viewing Switch Configu ration and Operati on . . . . . . . . . . . . . . . . . C-65 CLI: Viewing th e Startup or Running Conf iguration File . . . . . . . . . C-65 Web: Viewing the Configu ration File . . . . . . . . . . . . . . . . . . . . . . . . . C-65 CLI: Viewing a Summary of Switch Operat ional Data . . . . . . . . . . . C-65 Saving sho[...]

xix Viewing Information on Resource Usage . . . . . . . . . . . . . . . . . . . . . . . E-2 Policy Enforcement Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 When Insufficie nt Resource s Are Avai lable . . . . . . . . . . . . . . . . . . . . E-3 F Daylight Savings Time on ProCurve Switches G Network Out-of-Band Mana[...]

xx[...]

xxi Product Documentation About Y our Switch Manual Set Note For the latest version of sw itch documentatio n, please visit any of the follow- ing websites: www .procurve.com/manuals www .hp.com/go/blades ystem/documentation h18004.www1.hp. com/products/blades/ components/c-class-tech-installing.html Printed Publications The publicatio n listed bel[...]

xxii Software Feature Index This feature index indicates whi ch manual to co nsult for info rmation on a given softw are feature. Note This Index does not cover IPv6 capable software features. For informatio n on IPv6 protocol operatio ns and features (such as DHCPv6, DNS for IPv6, and Ping6), refer to the IPv6 Configuration Guide . Intelligent Edg[...]

xxiii Downloading Software X Event Log X Factory Default Settings X Flow Control (802.3x) X File T ransfers X Friendly Port Names X GVRP X Identity-Driven Management (IDM) X IGMP X Interface Access (T elnet, Console/Serial, Web) X IP Addressing X Jumbo Packets X LACP X LLDP X LLDP-MED X Loop Protection X MAC Address Management X MAC Lockdown X MAC [...]

xxiv Port Monitoring X Port Security X Port Status X Port T runk ing (LACP) X Port-Based Access Control (802.1X) X Protocol VLANS X Quality of Service (QoS) X RADIUS Authentication and Accounting X RADIUS-Based Configuration X RMON 1,2,3,9 X Secure Copy X SFTP X SNMPv3 X Software Downloads (SCP/SFTP , TFPT , Xmodem) X Source-Port Filters X Spanning[...]

xxv VLANs X W eb Authentication RADIUS Support X W eb-based Authentication X W eb UI X Intelligent Edge Software Features Manual Management and Configuration Advanced T raffic Management Multicast and Routing Access Security Guide[...]

1-1 1 Getting Started Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Command Syntax Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

1-2 Getting Started Intr oducti on Introduction This guide is inten ded for u se with the HP ProCurve 6 120G/XG and 61 20GX switches. It descri bes how to use the co mmand line interf ace (CLI), Me nu int erfac e, and we b browser t o configure, manage, mon itor , and troubl eshoot sw itch opera - tion. For an over view of prod uct docume ntation f[...]

1-3 Getting Started Conventions Command Prompts In the default co nfiguration, your switc h displays a CLI promp t similar to the following examples: ProCurve 6120G/XG Blade Switch# ProCurve 6120XG Blade Switch# T o sim plify recognition, this guid e uses ProCurve to represen t command prompts. For exampl e: ProCurve# (Y ou can use the ho stname co[...]

1-4 Getting Started Source s for More Informati on Sources for More Information For in formation ab out swi tch op eration and feat ures not co vered in this guide , consult the following sourc es: ■ Feature Inde x—For i nformat ion o n which man ual to consul t for a give n softwar e featur e, refer to the “Softwar e Feat ure Ind ex” on pa[...]

1-5 Getting Sta rted Source s for More Info rmatio n • file transfe rs, switch monitorin g, troubleshoo ting, and MAC addr ess manage ment ■ Advanced T raffic Management Guide —Use this guide for in formation on topics such as: • VLANs: Stat ic port-based a nd protocol V LANs, and dy namic GVRP VLANs • spann ing-T ree: 802.1D ( STP), 802.[...]

1-6 Getting Started Source s for More Informati on Getting Documentation From the W eb T o obtain the latest versio ns of documen tation and rel ease notes for yo ur switch, go to any of the f ollowin g web s ites: www .pro curve.co m/man uals www.hp.com/go/ bladesy stem/docu mentat ion h18004 .www1.hp .com/p roducts/b lades/ compone nts/c-c lass-t[...]

1-7 Getting Started Sources for More Information Command Line Interface If you need information on a specific comman d in the CLI, type t h e command name fo llowed by help . For example:  Figure 1-3. Example of CLI Help W eb Browser Interface If you need information on specific features in the HP ProCurve W eb Browser Interface (hereafter refer[...]

1-8 Getting Started Need Only a Quick Start? Figure 1-5. Button for Onboard Administrato r Interface Online Help Need Only a Quick Start? IP Addressing If you just want to give th e switch an IP address so that it can communicate on your network, or if you are not us in g VLANs, ProCur ve recommen ds that you use the Switch Setup sc reen to quickly[...]

1-9 Getting Started To Set Up and Install the Switch in Your Network ■ Instructions fo r physically installi ng the switch in your netw ork ■ Quickly assigning an IP address a nd subnet mask, set a Manager pass- word, and (optionally) conf igure other basic features. ■ Interpreting LED behavior . For the latest version of the Installation and[...]

2-1 Selecting a Management Interface Contents 2 Selecting a Management Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Understanding Physical Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Understanding Management I nterfaces . . . . [...]

2-2 Selecting a Management Interface Overview Overview This chapter describes the foll owing: ■ Physical Interfaces ■ Management interfaces ■ Advantages of using each interface Understanding Physical Interfaces Physical interfaces on the switch and th e C-c lass enclosure it is installed in provide the following options for a ccessing the man[...]

2-3 Selecting a Management Interface Understanding Management Interfaces Note The switches covered in th is guide allow up to 6 co nsole connection s. Console session 1 always belongs to the serial console, console session 2 always belongs to the USB serial consol e, and the remaining 4 can be used via ssh or telnet from a network connecti on. Unde[...]

2-4 Selecting a Management Interface Advantages of Usi ng the Menu Interface Advantages of Using the Menu Interface Figure 2-1. Example of the Console Inte rface Display ■ Provides quick, easy mana gement access t o a menu-driven subset of switch configurati on and performan ce features: The menu interface also provides access for: ■ Offers out[...]

2-5 Selecting a Management Interface Advantages of Using the CLI Advantages of Using the CLI Figure 2-2. Command Prompt Examples General Benefits ■ Provides access to the complete set of the switch configurat ion, perfor - mance, and diagnostic features. ■ Offers out-of-ban d access through the RS-232 connection and through the through the OA n[...]

2-6 Selecting a Management Interface Advantages of Using t he Web Browser Interface Advantages of Using the W eb Browser Interface Figure 2-3. Example of the Web Browser Interface ■ Easy access to the switch from anywhere on the network ■ Familiar browser interface --locations of window objects co nsistent with commonly used browsers, uses mous[...]

2-7 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus Advantages of Using ProCurve Manager or ProCurve Manager Plus Y ou can operate ProCurve Manager and ProC urve Manager Plus (PCM and PCM+) from a PC on t he network to mo nitor traffic, manage your hubs and switches, and proactively recommend network c[...]

2-8 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus PCM and PCM+ enable greater control, uptime, and performance in your network: ■ Features and benefits of ProCur ve Manager: • Network Status Summary: Upon boo t-up, a network status screen displays high-level information on ne twork devices, end n[...]

2-9 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus • Device Software Updates: This feature automatically obtai ns new device software images from ProC urve and updates devices, al lowing users to do wnload the latest ve rs ion or choose the desired version. Updates can be scheduled easily across lar[...]

2-10 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus clears the banner windo w and prompts the u ser for a passwor d (if configured). Following entry of the correct userna me /password informati on (or if no username/p assword is req uired), th e swit ch then displays either the Registra- tion page or [...]

2-11 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus Example of Configuring and Displaying a Banner Suppose a system operator wan ted to configure the following banner message on her comp any’ s switches: This is a private system maintained by the Allied Widget Corporation. Unauthorized use of this s[...]

2-12 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus Figure 2-7. The Current Banner Appear s in the Switch’ s Running-Config File The next time someone logs onto the switch’ s management CLI, the follow ing appears: Figure 2-8. Example of CLI Result of the Login Banner Configu ration ProCurve (conf[...]

2-13 Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus If someone uses a W eb browser to log in to the switch interface, the following message appears: Figure 2-9. Example of Web Browser Interface Result of th e Login Banner Configuration Operating Notes ■ The default banner appears only when the switc[...]

3-1 3 Using the Menu Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Starting and Ending a Me nu Session . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 How To Start a Menu Interface Session . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 How T[...]

3-2 Using the Menu Interface Overview Overview This chapter describes the follow ing features: ■ Overview of the Menu Interfa ce (page 3-2) ■ Starting and ending a Menu session (page 3-3) ■ The Main Menu (page 3-7) ■ Screen structure and naviga tion (page 3-9) ■ Rebooting the switch (page 3-12) The menu interface operates thro ugh the swi[...]

3-3 Using the Menu Interface Starting and Ending a Menu Session Note If the switch has neither a Manag er nor an Operator password, anyone having access to the console interface can ope rate the console with full manager privileges. Also, if you co nfigure only an Operator password, entering the Operator password en ables full manager privileges. F[...]

3-4 Using the Menu Interface Starting and Ending a Menu Session How T o Start a Menu Interface Session In its factory default configuration, th e switch console starts with the CLI prompt. T o use the menu interface with Manager privileges, go to the Manager level prompt and ent er the menu command. 1. Use one of these methods to connec t to the sw[...]

3-5 Using the Menu Interface Starting and Ending a Menu Session Figure 3-1. Example of the Main Menu with Mana ger Privileges For a description of Main Menu features, see “Main Menu Features” on page 3-7. Note T o configure the switch to start with th e menu interface inst ead of the CLI, go to the Manager lev el prompt in the CLI, enter the se[...]

3-6 Using the Menu Interface Starting and Ending a Menu Session Figure 3-2. Example Indicatio n of a Configuration Chan ge Requiring a Reboot 1. In the current session, if you have not made conf iguration changes that require a switch reboot to activate, return to the Main Menu and press [0] (zero) to log out. Then just exit from the te rminal prog[...]

3-7 Using the Menu Interface Main Menu Features Main Menu Features Figure 3-3. The Main Menu View with Manager Privileges The Main Menu gives you access to these Menu interface features: ■ Status and Counters: Provides access to di splay screens showing switch informat ion, port st atus and counters, and port and VLAN address tables. (Refer to Ap[...]

3-8 Using the Menu Interface Main Menu Features ■ Command Line (CLI): Selects the Command Line Interface at the same level (Manager or Operator) that you are accessing in the Menu interface. (Refer to Chapter 4, “Using th e Command Line Interface (CLI)”.) ■ Reboot Switch: Performs a “warm” reboot of the switch, which clears most tempora[...]

3-9 Using the Menu Interface Screen Structure and Navigation Screen Structure and Navigation Menu interface screens incl ude these three elements: ■ Parameter fields and/or read -onl y information such as statistics ■ Navigati on and config uration ac tions, such as Save , Edit, and Cancel ■ Help line to describe navigati on options, in divid[...]

3-10 Using the Menu Interface Screen Structure and Navigation T able 3-1. How T o Navig ate in the Menu Interf ace T ask: Action s : Execute an action from the “Actions –>” list at the bottom of the screen: Use either of the following methods: • Use the arrow keys ( [<] , or [> ] ) to highlight the action you want to execute, then [...]

3-11 Using the Menu Interface Screen Structure and Navigation T o get Help on i ndividual parameter de scriptions. In most screens there is a Help option in the Actions line. Whenever any of the items in the Actions line is highlig hted, press [H] , and a separate help screen is displa yed. For example: Figure 3-5. Example Show ing How T o Display [...]

3-12 Using the Menu Interface Rebooting the Switch Rebooting the Switch Rebooting the switch fr om the menu interface ■ T erminates all current sessions and performs a reset of the operating system ■ Activates any menu interface configuration changes that req uire a reboot ■ Resets statistical counters to zero (Note that statistical counters [...]

3-13 Using the Menu Interface Rebooting the Switch Rebooting T o Activate Configuration Changes. Configuration changes for most parameters in th e menu interface become ef fective as soon as you save them. However , you must reboot the switch in orde r to implement a change in the Maximum VLANs to support parameter . (T o access this parameter , go[...]

3-14 Using the Menu Interface Menu Features List Menu Features List Status and Counters • General System Information • Switch Management Address I nformation • Port Status • Port Counters • Address T able • Port Address T able Switch Configurat ion • System In formation • Port/T run k Settings • Network M onitoring Port • IP Con[...]

3-15 Using the Menu Interface Where To Go From Here Where T o Go From Here This chapter provides a n overview of th e menu interface and how to use it. The followi ng table indicates where t o turn for detailed informatio n on how to use the individual features av ailable through the menu interface. Option: Tu r n t o : T o use the Run Setup option[...]

4-1 4 Using the Command Line Interface (CLI) Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Accessing the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

4-2 Using the Command Line Interface (CLI) Overview Overview The CLI is a text-based command interf ace for configuring an d monitoring the switch. The CLI gives you access to the switch’ s full set of commands while providing the same password protection that is used in t he web browser interface and the menu interface. Accessing the CLI Like th[...]

4-3 Using the Command Line Interface (CLI) Using the CLI When you use the CLI to make a config uration change, the switch w rites the change to the Run ning-Config file in volatile memo ry . This a llows you to test your configurat ion changes be fore maki ng them permanent. T o make changes permanent, you must use t he write memory command to save[...]

4-4 Using the Command Line Interface (CLI) Using the CLI Caution ProCurve strongly recom mends that you co nfigure a Manager password. If a Manager password is not configured, th en the Manager level is not passw ord- protected, and anyone having in-band or ou t-of-band a ccess to the switch may be able to reach the Manag er level and compromise sw[...]

4-5 Using the Command Line Interface (CLI) Using the CLI Manager Privileges Manager privileges give you three additi onal levels of acce ss: Manager , Global Configuration, and Cont ext Configuration. A “ # ” character delimits any Man- ager prompt. For example: ProCurve #_ Example of the Manager prompt. ■ Manager level : Provides all Operat [...]

4-6 Using the Command Line Interface (CLI) Using the CLI T able 4-1. Privilege Level Hierarch y Privilege Level Example of Prompt and Permitted Operations Operator Privilege Operator Level ProCurve> sho w < command > setup ping < argument > link-test < argument > enable menu logout exit View status and configuration information[...]

4-7 Using the Command Line Interface (CLI) Using the CLI How T o Move Between Levels Moving Between the CLI and the Menu Interface. When moving between interfaces, the switch retains th e current privilege level (Manager or Operator). That is, if you are at the Operator level in the menu and select the Command Line Interfac e (CLI) option from the [...]

4-8 Using the Command Line Interface (CLI) Using the CLI For example, if you use the menu interf ace to configure an IP address of “ X ” for VLAN 1 and later use the CLI to co nfigure a different IP address of “ Y ” for VLAN 1, then “ Y ” replaces “ X ” as the IP address for VLAN 1 in the runni ng- config file. If you subsequently e[...]

4-9 Using the Command Line Interface (CLI) Using the CLI T y ping ? at the Manager level produces this listing: Figure 4-4.Example of the Manager-Level Command Listing When - - MORE - - appears, there are more comma nds in the listing. T o li st the next screenfull of commands, press the Space bar . T o list the remaining commands one-by-one, repea[...]

4-10 Using the Command Line Interface (CLI) Using the CLI As mentioned above, if you type part of a command word and press [T ab] , the CLI completes the current wo rd (if you have typed enou gh of the word for the CLI to distingui sh it from ot her possibilitie s), including hyph enated exten- sions. For ex ample: ProCurve (config)# port- [T ab] P[...]

4-11 Using the Command Line Interface (CLI) Using the CLI Displaying CLI “Help” CLI Help provides two types of context-sensitive info rmation: ■ Command list with a brief summary of each command’ s purpose ■ Detailed informati on on how to use indivi dual command s Displaying Command-List Help. For example, to list the Operator -Level com[...]

4-12 Using the Command Line Interface (CLI) Using the CLI Figure 4-7.Example of How T o Display Help for a Specific Command Note that trying to list the help for an individual command from a privilege level that does no t includ e that command results in an error message. For example, trying to li st the help for th e interfac e command while at th[...]

4-13 Using the Command Line Interface (CLI) Using the CLI Configuration Comma nds and the Context Configuration Modes Y ou can execute any configuration comma nd in the global configuration mode or in selected context modes. However , using a c ontext mode enables you to execute context-specific commands fast er , with shorter command strings. The [...]

4-14 Using the Command Line Interface (CLI) Using the CLI Figure 4-8. Context-Specific Com mands Affecting Po rt Context In the port context, the first block of commands in the “?” listing show the context-specif ic commands that will affect only ports C3-C6. The remaining commands in the listing are Manager , Operator , and context commands.[...]

4-15 Using the Command Line Interface (CLI) Using the CLI VLAN Context . Includes VLAN-specific command s that apply only to the selected VLAN, plus Manager and Op erator command s. The prompt for this mode includes the VLAN ID of the sel ected VLAN. For example, if you had already configur ed a VLAN with an ID of 100 in the switch: Figure 4-9. Con[...]

4-16 Using the Command Line Interface (CLI) CLI Control and Editing CLI Control and Editing Executing a Prior Command—Redo The redo command executes a prior command in th e history list. Figure 4-10. Example of the redo Comman d Repeating Execution of a Command The repeat comman d execute s a previ ous command in the history lis t. Syntax: redo [[...]

4-17 Using the Command Line Interface (CLI) CLI Control and Editing For example: ProCurve(config)# repeat 1-4,7-8,10 count 2 delay 3 Figure 4-11. Example of repeat Command Usi ng a Range Syntax: repeat [cm dlist] [count] [delay] Repeats execution of a previous command. Repeats the last command by default until a key is pressed. cmdlist: If a number[...]

4-18 Using the Command Line Interface (CLI) CLI Control and Editing Using a Command Alias Y ou can create a simple comma nd alias to use in place of a command name and its options. Choose an alias n ame that is not an existing CLI command already . Existing CLI commands are se arched before looking for an alias command; an alias that is identical t[...]

4-19 Using the Command Line Interface (CLI) CLI Control and Editing Figure 4-12. Example of Using the Alia s Command with sh ow int custom Note Remember to enclose the command being aliased in quotes. Command paramete rs for the ali ased comm and can be added at the end of the alias command string. For example: ProCurve(config)# alias sc “show co[...]

4-20 Using the Command Line Interface (CLI) CLI Control and Editing Figure 4-13. Example of Alias Commands and Th eir Configurations CLI Shortcut Keystrokes ProCurve(config)# show alias Name C ommand -------------------- ---- -------------------------- sc show config sic show int cus tom 1-4 port name:4 type vlan in trusion spee d enabled mdi Keyst[...]

5-1 5 Using the ProCurve W eb Browser Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Starting a Web Browser Interface Session with the Switch . . [...]

5-2 Using the ProCurve Web Browser Interface Overview Overview The ProCurve web browser interface buil t into the switch lets you easily access the switch f rom a browser - based PC on yo ur network. Th is lets you do the followin g: ■ Optimize your network upt ime by using the Alert Log and other diagnost ic tools ■ Make config uratio n change[...]

5-3 Using the ProCurve Web Browser Interface General Features General Features The web browser interface includes these features: Switch Identity and Status: • General system da ta • Software version • IP address • Status Overview • Port utilizat ion • Port counters •P o r t s t a t u s • Alert log Switch Configu ration: • Device [...]

5-4 Using the ProCurve Web Browser Interface Starting a Web Browser Interface Session with the Switch Starting a W eb Browser Interface Session with the Switch Y ou can star t a web browser session in the following wa ys: ■ Using a standalone web b rowser on a networ k connection from a PC or UNIX workstation: • Directly connected to your netwo[...]

5-5 Using the ProCurve Web Browser Interface Starting a Web Browser Interface Session with the Switch Using ProCurve Ma nager (PCM) or ProCurve Manager Plus (PCM+) ProCurve Manager and ProCurve Manager Pl us are designed for i nstallation on a network management w orkstation. For this reason, the system require- ments are different from the system [...]

5-6 Using the ProCurve Web Browser Interface Starting a Web Browser Interface Session with the Switch Figure 5-1. Example of Status Overview Screen First time install alert[...]

5-7 Using the ProCurve Web Browser Interface Tasks for Your First ProCurve Web Browser Interface Session T asks for Y our First ProCurve W eb Browser Interface Session The first time you a ccess the web browse r interface, there ar e three ta sks you should perform: ■ Review the “First Time Install” window ■ Set Manager and Op erator passwo[...]

5-8 Using the ProCurve Web Browser Interface Tasks for Your First ProCurve Web Browser Interface Session This window is the la unching point f o r the basic configur ation you need to perform to set web browser interf ace pa sswords for maintaining security and a fault detection policy , which determin es the types of messages that the Alert Log di[...]

5-9 Using the ProCurve Web Browser Interface Tasks for Your First ProCurve Web Browser Interface Session Figure 5-3. The Device Passwords Window T o set the passwords: 1. Access the Device Passwords screen by one of th e following m ethods: • If the Alert Log includes a “First T ime Install” event entry , double click on this event, then, in [...]

5-10 Using the ProCurve Web Browser Interface Tasks for Your First ProCurve Web Browser Interface Session Entering a User Name and Password Figure 5-4. Example of the Password Prompt in the W e b Browser Interface The manager and operator passw ords are us ed to control access to all sw itch interfaces. Once set, y ou will be prompt ed to supply th[...]

5-11 Using the ProCurve Web Browser Interface Tasks for Your First ProCurve Web Browser Interface Session The Clear button is provided for your convenience, but its presence means that if you are concerned with the security of the switch configuration and operation, you should make sure the swit ch is installed in a secure location, such as a locke[...]

5-12 Using the ProCurve Web Browser Interface Support/Mgmt URLs Feature Support/Mgmt URLs Feature The Support/Mgmt URLs window en ables you to change the W orld W ide W eb Universal Resource Locat or (URL) for two functi ons: ■ Support URL – A support information site for your switch ■ Management S erver URL – The web site for web browser o[...]

5-13 Using the ProCurve Web Browser Interface Support/Mgmt URLs Feature Support URL For technical support, go to: www .hp.com/#Support. Help and the Manage ment Server URL The Management Server URL field specifies the U RL the switch uses to find online Help for the w eb browser interface. ■ If you install PCM (ProCurve Manager) in your network, [...]

5-14 Using the ProCurve Web Browser Interface Support/Mgmt URLs Feature Using the PCM Server for Switch W eb Help For ProCurve devices that support the “W eb Help” feature, you can use the PCM server to host the switch help files for devices that do not have HTTP access to the ProCurve Support W eb site. 1. Go to the ProCurve Support web site t[...]

5-15 Using the ProCurve Web Browser Interface Support/Mgmt URLs Feature 3. Add an entry , or edit the existing entry i n the Discovery por tion of the global properties (globalpro ps.prp) in PCM to redire ct the switches to the help files on the PCM server . For example: Global { T empDi r=data/temp ... Discovery{ ... ... DeviceHelpUrlRedirect=htt [...]

5-16 Using the ProCurve Web Browser Interface Status Reporting Features Status Reporting Features Browser elemen ts covered in this section includ e: ■ The Overv iew window (below) ■ Port utilization and status (page 5-17) ■ The Alert log (page 5-20) ■ The Status bar (page 5-22 ) The Overview W indow The Overvi ew W indow is the home screen[...]

5-17 Using the ProCurve Web Browser Interface Status Reporting Features Policy Management and Configuration. PCM can perform network-wide policy management and conf igurat ion of your switch . The Management Server URL field (page 5-13) shows the URL fo r the management station performing that function. For more info rmation, re fer to the document[...]

5-18 Using the ProCurve Web Browser Interface Status Reporting Features ■ % Error Pkts Rx : All er ror packets received by the port. (T his indicator is a reddish color on many system s.) Although errors re ceived on a port are not propagated to the rest of the network, a consistently high number of errors on a specific port ma y indicate a probl[...]

5-19 Using the ProCurve Web Browser Interface Status Reporting Features Figure 5-11. Display of Nume rical V alue s for the Bar Port Status Figure 5-12. The Port Status Indic ators and Legend The Port Status in dicators show a symbol f or each port that indicate s the general status of the port. Th ere are four possible statuses: ■ Port Connected[...]

5-20 Using the ProCurve Web Browser Interface Status Reporting Features The Alert Log The web browser interface Al ert Log, sh own in the lo wer half of the screen, shows a list of network occurrences, or alerts , that were detected by the switch. T ypical alerts are Broadcast Storm , indicating an exc essive number of broadcasts received on a port[...]

5-21 Using the ProCurve Web Browser Interface Status Reporting Features Alert T ypes and Detailed Views As of June, 2007, the web browser in terface generates th e following alert types: Note When troubleshooting the sources of aler ts, it may be helpful to check the switch’ s Port Stat us and Port Count er windows, or use the CL I or menu interf[...]

5-22 Using the ProCurve Web Browser Interface Status Reporting Features Figure 5-14. Example of Alert Log Detail View The Status Bar The Status Bar appears in the uppe r left corner of the web browser interface window . Fig ure 5-15 shows an expa nded view of the status bar . Figure 5-15. Example of the Status Bar Status Indicator Most Critical Ale[...]

5-23 Using the ProCurve Web Browser Interface Status Reporting Features The Status bar includes fo ur objects: ■ Status Indicator . Indicates, by icon, the severi ty of the most critical alert in the current di splay of the Aler t Log. This ind icator can be one of f our shapes and colo rs, as shown below . T able 5-1. Sta tus Indicator Key ■ S[...]

5-24 Using the ProCurve Web Browser Interface Status Reporting Features Setting Fault Detection Policy One of the powerful features in the web browser interface is the Fault Detection facility . For your switch, this feature controls the types of alerts reported to the Alert Log based on their level of severity . Set this policy in the Fault De tec[...]

5-25 Using the ProCurve Web Browser Interface Status Reporting Features T o pro vide the most information on network problems in the Alert Log, the recommended sensitivity level for Log Network Problems is High Sensitivity . The Fault Detec tion settings a re: ■ High Sensitivity . This policy direct s the switch to send all alerts to the Alert Lo[...]

6-1 6 Switch Memory and Configuration Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Configuration File Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Using the CLI To Implement Configuration Changes . . . . . . . . . . . . 6-6 Using the[...]

6-2 Switch Memory and Configuration Contents Changing or Overriding t h e Reboot Configur ation Polic y . . . . . . . . . 6-30 Managing Startup-Confi g Files in the Switch . . . . . . . . . . . . . . . . . . . 6-32 Renaming an Existing Start up-Config File . . . . . . . . . . . . . . . . . . 6-33 Creating a New Startup-Config File . . . . . . . . .[...]

6-3 Switch Memory and Configuration Overview Overview This chapter describes: ■ How switch memory manag es configu ration ch anges ■ How the CLI implements configurat ion changes ■ How the menu interface and web br owse r interface im plement configu- ration changes ■ How the swit ch provides softwar e options through pr imary/seco ndary fl[...]

6-4 Switch Memory and Configuration Configuration File Management ■ Startup-config File: Exists in flash (non-vo latile) memory and is used to preserve the most recently-save d configuration as the “permanent” configuration. Booting the swit ch repla ces the current runnin g-config file with a new run- ning-config file that is an exact copy o[...]

6-5 Switch Memory and Configuration Configuration File Management The above command disables port 5 in th e running-config file, but not in the startup-co nfig file. Port 5 remains disabled only until the switch reboots. If you want port 5 to remain disabl ed through the next reboot, use write memory to save the current running-config file to the s[...]

6-6 Switch Memory and Configuration Using the CLI To Implement Configuration Changes Using the CLI T o Implement Configuration Changes The CLI offers these capabili ties: ■ Access to the fu ll set of swit ch configuration f eatures ■ The option of testing configuration changes before making them perma- nent How T o Use the CLI T o V iew the Cur[...]

6-7 Switch Memory and Configuration Using the CLI To Implement Configuration Changes 3. Observe the switch’ s performance wi th the new parameter settin gs to verify the effect of your changes. 4. When you are satisfied that you have the correc t parameter settings, use the write memory command to copy the changes to the startup-config file. For [...]

6-8 Switch Memory and Configuration Using the CLI To Implement Configuration Changes How T o Cancel Changes Y ou Have Made to the Running-Config File. If you use th e CLI to chan ge parameter settings in th e running-config f ile, and then decide that you d on’t want those changes to remain, you can use either of the following methods to remove t[...]

6-9 Switch Memory and Configuration Using the CLI To Implement Configuration Changes Note If you use the CLI to ma ke a change to th e running- config fi le, you should either use the write memory command or select th e save option all owed during a reboot (figure 6-6-2, above) to save th e change to the startup-config file. That is, if yo u use th[...]

6-10 Switch Memory and Configuration Using the Menu a nd Web Browser Inte rfaces To Implement Configuration Changes Using the Menu and W eb Browser Interfaces T o Implement Configuration Changes The menu and web browser inte rfaces offer these advantages: ■ Quick, easy menu or w indow access to a sub set of switch configuration features ■ Viewi[...]

6-11 Switch Memory and Configuration Using the Menu and Web Browser Interfaces To Imple m ent Configuration Changes Figure 6-4. Example of Pending Configuration Chan ges Y ou Can Save or Cancel Note If you reconfigure a parame ter in the CLI and then go to the menu interface without executing a wr ite memory command, those c hanges are stored only [...]

6-12 Switch Memory and Configuration Using the Menu a nd Web Browser Inte rfaces To Implement Configuration Changes Figure 6-5. The Reboot Switch Option in th e Main Menu Rebooting T o Activate Configuration Changes. Configuration changes for most parameters become effective as soon as you save them. However , you must reboot the swit ch in or der [...]

6-13 Switch Memory and Configuration Using the Menu and Web Browser Interfaces To Imple m ent Configuration Changes Figure 6-6. Indication of a Configuratio n Change Requiring a Reb oot W eb: Implementing Configuration Changes Y ou can use the web browser interface to simultaneously save and implement a subset of switch config uration changes w ith[...]

6-14 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Using Primary and Secondary Flash Image Options T he s w i t c h e s covered in this guide f eature two flash memory locations for storing switch software im age files: ■ Primary Flash: The defaul t storage for a switch software image. ■ Secondary Flash: The ad[...]

6-15 Switch Memory and Configuration Using Primary and Secondary Flash Image Options For example, if the switch is using a software version of K.12.XX stored in Primary flash, show version produces the following: Figure 6-7. Example Showing the Identity of th e Current Flash Image Determining Whethe r the Flash Images Are Different V ersions. If th[...]

6-16 Switch Memory and Configuration Using Primary and Secondary Flash Image Options switch from the opposite flash image and using show version again, you can determine the version(s) of sw itch soft ware in both flash sources. For exam- ple: Figure 6-9. Determining the Software Ve rsion in Primary and Secondary Fl ash Switch Software Downloads Th[...]

6-17 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Note xmodem should not be used over the OA serial con sole. It should only be used over the USB serial console connection. Download Interruptions. In most cases, if a power failure or other ca use interrupts a flash image download, th e switch reboots with the imag[...]

6-18 Switch Memory and Configuration Using Primary and Secondary Flash Image Options flash image in RAM. Do not reboot the switch . Instead, immediately dow nload another valid fla sh image to primary or secondary flash. Otherwise, if the switch is rebooted withou t a software imag e in eith er primary or se condary flash, the temporary flash image[...]

6-19 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Syntax: erase flash < primary | secon dary > For example, to erase the software ima ge in primary flash, do the following: 1. First verify that a usable flash image exists in secondary flash. The most reliable way to ensure this is to reboot the sw itch from [...]

6-20 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Image does not exist Operation aborted. Interaction of Primary and Secondar y Flash Images with the Current Configuration. The switch has one startup-config file (page 6-3), wh ich it always uses for reboots, regardless of whether the reboot is from pr imary or sec[...]

6-21 Switch Memory and Configuration Using Primary and Secondary Flash Image Options T able 6-2. Comparing the Boot and Rel oad Commands Setting the Default Flash Y ou can specify the default flash to bo ot from on the n ext boot by entering t he boot set-default fl ash command. Figure 6-13.Example of boot set-d efault Command wi th Default Flash S[...]

6-22 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Booting from the Default Flash (Primary or Secondary) The boot command boots the switch from the flash image that you are currently boot ed on, or the f lash image that was set eithe r by the boot set - default command or b y the last execu ted boot system flash &l[...]

6-23 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Figure 6-15. Exampl e of Boot Command with Secondary Flash Op tion In the above example, typi ng either a y or n at the second prompt initiate s the reboot operation. Using the Fastboot feature. The fastboot command allows a boot sequence that skips the internal po[...]

6-24 Switch Memory and Configuration Using Primary and Secondary Flash Image Options Figure 6-16. Using Reload with Redundant M ana gement and Pending Con figuration Changes Scheduled Reload. Ad ditional parameters in t he reload command allow for a scheduled reboot of t h e switch via the CLI. The scheduled reload feature removes th e requirement [...]

6-25 Switch Memory and Configuration Multiple Configuration Files Multiple Configuration Files This method of operation mean s that you cannot preserve different start up- config files across a re boot wi thout using remote storage. The switch allows up to three startup-config file s with options for selecting which startup-c onfig file to use fo r[...]

6-26 Switch Memory and Configuration Multiple Configuration Files ■ T ransitions fro m one software rele ase to anothe r can be performed whil e maintaining a separate con figuration for the dif ferent software re lease versions. ■ By setting a reboot policy using a known good co nfiguration and t hen overriding the policy on a per -instance ba[...]

6-27 Switch Memory and Configuration Multiple Configuration Files 2. Use the CLI to make configura tion ch anges in the running-config file, and then execute write mem . The result is that the startup-config fi le used to reboot the sw itch is modifi ed by the acti ons in step 2. Figure 6-18. Exampl e of Reboot Process and Making Changes to the Sta[...]

6-28 Switch Memory and Configuration Multiple Configuration Files ■ Saves a copy of the existing startup-co nfig f ile in memory slot 2 with the filename wo rkingConfig . ■ Assigns the workingConfig file as the active configur ation and the default configuratio n for all subsequent reboo ts using either primary or second- ary flash. Figure 6-19[...]

6-29 Switch Memory and Configuration Multiple Configuration Files Listing and Displaying Startup-Config Files V iewing the Startup-Config File Status with Multiple Configuration Enabled Rebooting th e switch autom atically ena bles the mult iple configur ation fea- ture. Command Page show config files Below show config < filename >6 - 3 0 Syn[...]

6-30 Switch Memory and Configuration Multiple Configuration Files Displaying the Content of A Specific Startup-Config File W it h Multiple Configu ration enabled , th e switch can have up to three startup- config files. Because the sh ow config command alw ays displays the content of the currently active st artup-config f ile, the command extensi o[...]

6-31 Switch Memory and Configuration Multiple Configuration Files For example, suppose: ■ Software release “A” is stored in prim ary flash and a later software rele ase is stored in secondary flash. ■ The system operator is using memo ry slot 1 for a reliable, minimal configuration (named minconfig ) for the software versi on in the primary[...]

6-32 Switch Memory and Configuration Multiple Configuration Files ProCurve(config)# startup-default pri config minconfig ProCurve(config) # startup-default sec config newconfig. Overriding the Default Re boot Configuration Policy . This co mmand provides a method for manually r ebootin g with a specific startup-config file other than the f ile spec[...]

6-33 Switch Memory and Configuration Multiple Configuration Files Renaming an Existing Startup-Config File Creating a New Startup-Config File The switch allows up to three startup-conf ig files. Y ou can create a new startup-co nfig file if th ere is an empty memo ry slot or if yo u want to replace one startup- config file with ano ther . Syntax: r[...]

6-34 Switch Memory and Configuration Multiple Configuration Files For example, suppose bo th primary and secondary flash memo ry contain software release “A” and use a star tup-config file n amed config1 : Figure 6-20. Exampl e of Using One Startup-Config File for Bo th Primary and Secondary Flash This command makes a local co py of an existing[...]

6-35 Switch Memory and Configuration Multiple Configuration Files If you wanted to experiment with co nfiguration changes to the software version in secondary flash, yo u could create and assign a separate startup- config file for this purpo se. Figure 6-21. Exampl e of Creating and Assigning a New Startup-Confi g File Note Y ou can also gene rate [...]

6-36 Switch Memory and Configuration Multiple Configuration Files Figure 6-22 illustrates using erase config < filename > to remove a startup-config file. Figure 6-22. Exa mple of Erasing a Non-Acti ve Startup-Config File Note: Where a file is assigned to either the primary or the secondary flash, but is not the currently active startup- conf[...]

6-37 Switch Memory and Configuration Multiple Configuration Files W ith the same memory configuration as is sh own in the bottom portion of figure 6-22, executing erase startup-config boots the switch from primary flash, resulting in a new file nam ed minconfig in t he same memory slot. The ne w file contains the defaul t configuration for the soft[...]

6-38 Switch Memory and Configuration Multiple Configuration Files TFTP: Copying a Configurati on File to a Remote Host For example, the followin g command copies a startup-config fil e named test- 01 from the switch to a (UNIX) TFTP server at I P address 10.10.28.14: ProCurve(config)# copy config test-01 tftp 10.10.28.14 test-01.txt unix copy confi[...]

6-39 Switch Memory and Configuration Multiple Configuration Files TFTP: Copying a Configuration File from a Remote Host For example, the followin g command copies a startup-config fil e named test- 01.txt from a (UNIX) TFTP server at IP address 10.10.28.14 to the first empty memory slot in the switch: ProCurve(config)# copy tftp config test-01 10.1[...]

6-40 Switch Memory and Configuration Multiple Configuration Files Xmodem: Copying a Configuration File to a Serially Connected Host Xmodem: Copying a Configuration from a Serially Connected Host Syntax: copy config < filena me > xmodem < pc | unix > [o obm] This is an addition to the copy < config > xmodem command options. Use thi[...]

6-41 Switch Memory and Configuration Automatic Configuration Update with DHCP Option 66 Operating Notes for Multiple Configuration Files ■ SFTP/SCP: The configur ation files are available for sftp/scp transfer as /cfg/< filenam e > . Automatic Configuration Update with DHCP Option 66 ProCurve switches are initially booted up with the factor[...]

6-42 Switch Memory and Configuration Automatic Configuration Update with DHCP Option 66 Possible Scenarios for Upda ting the Configuration File The followin g table shows various network configurations and how Option 66 is handled. Operating Notes Replacing the Existi ng Configuratio n File : After the DHCP client down- loads the co nfigurat ion fi[...]

6-43 Switch Memory and Configuration Automatic Configuration Update with DHCP Option 66 Global DHCP Parameters : Global parameters are processed only if received on the primary VLAN. Best Offer : The “Best Offer” is the best DHCP or BootP off er sent by the DHCP server in response to the DHCPREQUEST sent by the switch. The criteria for selectin[...]

7-1 7 Interface Access and System Information Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Interface Access: Console/Serial Link, Web, and Inbound Telnet . 7-3 Menu: Modifying the Interface Access . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 CLI: Modifying[...]

7-2 Interface Access and System Information Overview Overview This chapter describes how to: ■ View and modify the configuration for switc h interface access ■ Use the CLI kill command to terminate a remote session ■ View an d modify switch system information For help on how to actual ly use the interfaces built in to the switch, refer to: ?[...]

7-3 Interface Access and System Information Interface Access: Cons ole/Serial Link, W eb, and Inbound Telnet Interface Access: Console/Serial Link, W eb, and Inbound T elnet Interface Access Features In most cases, the default configuratio n is acceptable for standard operation. Note Basic switch security is through passw ords. Y ou can gain additi[...]

7-4 Interface Access and System Information Interface Access: Console/Serial Link, Web, and Inbound Telnet Menu: Modifying the Interface Access The menu interface enables you to modify these parameters: ■ Inactivity T im eout ■ Inbound T elnet Enabled ■ W eb Agent Enabled T o Access the Interface Access Parameters: 1. From the Main Menu, Sele[...]

7-5 Interface Access and System Information Interface Access: Cons ole/Serial Link, W eb, and Inbound Telnet CLI: Modifying the Interface Access Interface Access Commands Use d in This Section Listing the Current Console/Serial Li nk Configuration. This com- mand lists the current interface access parameter settings. Syntax: show console This examp[...]

7-6 Interface Access and System Information Interface Access: Console/Serial Link, Web, and Inbound Telnet Outbound T elnet to Another Device. Thi s feature operates indepen- dently of th e telnet-server status and e nables you to T elnet to another device that has an IP address. For example, if the host “Labswitch” is in the domain abc.com, yo[...]

7-7 Interface Access and System Information Interface Access: Cons ole/Serial Link, W eb, and Inbound Telnet Figure 7-3. Example of show teln et Command Displaying Reso lved IP Addresses Reconfigure W eb Browser Access. In the default co nfigurati on, web browser access is enabled. Syntax: [no] web-managem ent [listen <oobm | data | both>] Us[...]

7-8 Interface Access and System Information Interface Access: Console/Serial Link, Web, and Inbound Telnet T o di sable web bro wser access: ProCurve(config)# no web-management T o re-enable w eb browser access: ProCurve(config)# web-management Reconfigure the Console/Seri al Link Settings. Y ou can reconfigure one or more console parameters with o[...]

7-9 Interface Access and System Information Interface Access: Cons ole/Serial Link, W eb, and Inbound Telnet Note If you change the Baud Rate or Flow Control settings for the switch, you should make the corresp ond ing changes in your co nsole access de vice. Oth- erwise, you may lose connectivity betw een the switch an d your terminal emulator due[...]

7-10 Interface Access and System Information Interface Access: Console/Serial Link, Web, and Inbound Telnet Y ou can also execute a se ries of co nsole commands and then save the configuration and boot the switch . For exam ple: Figure 7-5. Example of Execu ting a Series of Console Co mmands Configure the individua l parameters. Save the changes . [...]

7-11 Interface Access and System Information Denying Interface Access by Termi nating Remote Management Sessions Denying Interface Access by T erminating Remote Management Sessions The switch supports up to five ma nagement sessions. Y ou can use show ip ssh to list the current management sessions, and kill to terminate a currently running remote s[...]

7-12 Interface Access and System Information System Information System Information System Information Feat ures Configuring system i nformation is optional, but recomm ended. System Name: Using a unique name helps you to identi fy individu al devices where you are using an SNMP network management tool such as ProCurve Manager . System Contact and L[...]

7-13 Interface Access and System Information System Information Ti m e Z o n e : The number of minutes your time z o n e l o c a t i o n i s t o t h e We s t ( + ) or East (-) of Co ordinated Universal T ime (formerly GMT). Th e default 0 means no time zone is configured. For example, the time zone for Berlin, Germany is + 60 (minutes) and the time[...]

7-14 Interface Access and System Information System Information 2. Press [E] (for E dit). The cursor moves to the System Name field. 3. Refer to the on line help provided wi th this screen for furthe r information on configurat ion options for t hese features . 4. When you have finished making ch anges to the above parameters, press [Enter] , then [...]

7-15 Interface Access and System Information System Information Listing the System Encl osure Informatio n. This command lists the sys- tem enclosure information. Syntax: show system enclosure This example shows the switch ’ s enclosure configuration. Figure 7-9. Example of CLI System Enclosure In formation Listing Configure a System Na me, Conta[...]

7-16 Interface Access and System Information System Information Figure 7-10. System Information Listing After Execu ting the Preceding Co mmands The menu interface wi ll only display up to 47 characte rs although you can specify a name up to 255 characters in length. A message be ginning with “+” displays if the name exceeds 4 7 characters. Y o[...]

7-17 Interface Access and System Information System Information Figure 7-11. Menu Screen Showing System Information The W eb Browser interface also allo ws you to enter a maximum of 255 characters. Y ou can view all the charac ters by using the cursor to scroll through the fie ld. Figure 7-12. System Location and System Con tact in the Web Browser [...]

7-18 Interface Access and System Information System Information Syntax: mac-age-time < 10 - 1000000 > (seconds) Allows you to set the MAC address table’ s age-o ut interval . An address is aged out if the switch does not receive traffic from that MAC address for the age-out interval, measured in seconds. Default: 300 seconds. For example, t[...]

7-19 Interface Access and System Information System Information W eb: Configuring System Parameters In the web browser interface, you can enter the following sy stem informat ion: ■ System Name ■ System Locati on ■ System Contact For access to the MAC Age Interval and the T ime parameters, use the menu interface or the CLI. Configure System P[...]

8-1 8 Configuring IP Addressing Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Just Want a Quick St art with IP Addr essing? . . . . . . . . . . . . . . . .[...]

8-2 Configuring IP Addressing Overview Overview Y ou can configure IP addressing throug h all of the switch’ s interfaces. Y o u can also: ■ Easily edit a switch conf iguration fi le to allow downloadi ng the file to multiple switches withou t overwriting each switc h’ s unique gateway and VLAN 1 IP addressing. ■ Assign up to 32 IP addresse[...]

8-3 Configuring IP Addressing IP Configuration use the men u interface o r the CLI to manually c onfigure the initial IP va lues. After you have network access to a device, you can use the web browser interface to m odify the initial I P configuration if needed. For informati on on how IP add ressing affects swit ch operati on, refer to “How IP A[...]

8-4 Configuring IP Addressing IP Configuration For more on using the Switch Se tup screen, refer to the In stallation a nd Getting Started Guide you rec eived wi th the swi tch. IP Addressing with Multiple VLANs In the factory-d efault configu ration, the switch has one, permanent default VLAN (named DEF AUL T_VLAN) that in cludes all ports on the [...]

8-5 Configuring IP Addressing IP Configuration Menu: Configuring IP Addres s, Gateway , and T ime-T o- Live (TTL) Do one of the followin g: ■ T o manually enter an IP address, subnet mask, set the IP Config parameter to Manual and then manually enter the I P addres s and subnet ma sk values you want for the switch. ■ T o use DHCP or Bootp, use [...]

8-6 Configuring IP Addressing IP Configuration 3. If the switch needs to access a router , for exampl e, to reach off-subnet destinations, select the Default Ga teway field and enter the IP address of the gateway router . 4. If you ne ed to change the packet T im e-T o- Live (TTL) setting, select Default TTL and type in a value between 2 and 255. 5[...]

8-7 Configuring IP Addressing IP Configuration (Y ou can al so use the show managemen t command to display the IP addressing and time server IP addressing config ured on the switch. Refer to figure 9-6 on page 9-10.) For example, in the factor y-default configuratio n (no IP addressing assigned), the switch’ s IP addressing appears as: Figure 8-2[...]

8-8 Configuring IP Addressing IP Configuration Note The default IP address setting for the DEF AUL T_VLAN is DHCP/Bootp . On additional VLANs you create, the default IP address setting is Disabled . Syntax: [ no ] vlan < vlan-id > ip address <ip-address/mask-length> or [ no ] vlan < vlan-id > ip address < ip-ad dress > < [...]

8-9 Configuring IP Addressing IP Configuration Figure 8-4. Example of Configu ring and Displaying a Mult inetted VLAN If you then wa nted to mu ltinet the default VLA N, you woul d do the fol lowing: Figure 8-5. Example of Multinett ing on the Default VLAN Note The Internet (IP) Se rvice screen in the Menu inte rface (figure 8-1 on page 8-5) displa[...]

8-10 Configuring IP Addressing IP Configuration Removing or Replacin g IP Addresses in a Multinetted VLAN. To remove an IP address from a multinetted VLAN, use the no form of the IP address command shown on page 8-8. Ge nerally , to replace one IP address with anothe r , you shou ld first r emove the address you wan t to replace, an d then enter th[...]

8-11 Configuring IP Addressing IP Configuration 3. If you need further inform ation on using the web browser interface, click on [?] to access the we b-based help available for the switch. How IP Addressing Affe cts Switch Operation W ithout an IP address and subnet mask compatible with your network, the switch can be managed only through a direct [...]

8-12 Configuring IP Addressing IP Configuration DHCP/Bootp Operation Overview . DHCP/Bootp is used to provide confi guration data from a DHCP or Bootp server to the swit ch. This data can be the IP ad dress, subnet mask, default gateway , T imep Server address, and TFTP server add ress. If a TFTP server address is provided, this allows the swit ch [...]

8-13 Configuring IP Addressing IP Configuration DHCP Operation. A significant differenc e between a DHCP configuration and a Bootp configurat ion is that an IP address assi gnment from a DHCP server is automatic. Depe nding on how t he DHCP serv er is configu red, the switch may receive an IP address that is temporari ly leased . Peri odically the [...]

8-14 Configuring IP Addressing IP Configuration gw=10.66.77.1: lg=10.22.33.44: T144=”switch.cfg”: vm=rfc1048 where: Note The above Bootp table entry is a sample that will work for the switch when the appropriate addresses and file names are used. Network Preparations fo r Configuring DHCP/Bootp In its default configuratio n, the switch is co[...]

8-15 Configuring IP Addressing IP Configuration Note Designating a primary VLAN other than the default VLAN affe cts the switch’ s use of informati on received via DHCP/Boo tp. For more on this topi c, refer to the chapter describing VLANs in the Advanced T raffic Management Guide for your switch. After you reconfigure or reboot the switch with D[...]

8-16 Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads IP Preserve: Retaining VLAN-1 IP Addressing Across Configuration File Downloads For the switches co ver ed i n th is g ui de, IP Preserve enables you to copy a configuratio n file to multiple swi tches while retain ing the individua l IP [...]

8-17 Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Enabling IP Preserve T o set up IP Pres erve, enter the ip pr eserve statement at the end of a configu- ration file. (Not e that you d o not ex ecute IP Preserve by entering a command from the CLI). Figure 8-6. Example of Impl ementing IP[...]

8-18 Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Figure 8-8. Configuration Fil e in TFTP Server , with DHCP/Bootp Specified a s the IP Addressing Source If you apply this configuration file to fi gure 8- 7, switches 1 - 3 will still retai n their manually assigned IP addressing . Howeve[...]

8-19 Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Figure 8-9. Configuration Fil e in TFTP Server , with Dedicated I P Addressing Instead of DHCP/Bo otp T o summarize the IP Pres erve effect on IP addressing: ■ If the switch recei ved its most recent VLAN 1 IP addressing from a DHCP/ Bo[...]

9-1 9 T ime Protocols Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 TimeP Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 SNTP Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Sel[...]

9-2 Time Protocols Overview Overview This chapter describes: ■ SNTP T ime P rotocol Operation ■ T imep Ti me Protocol Operation Using time synchron ization ensures a u niform time among interoperating devices. This helps you to manage a nd troubleshoot switch operation by attaching meaningful time data to event and error messages. The switch of[...]

9-3 Time Protocols Selecting a Time Synchronization Protocol or Turning Off Time Protocol Operation Note T o use Broadca st mode, the switc h and th e SNTP server must be in the same subnet. ■ Unicast Mode: The switch requests a time update from the config- ured SNTP se rver . (Y ou can co nfigure one server usin g the menu interface, or up to th[...]

9-4 Time Protocols SNTP: Viewing, Selecting, and Configuring ■ In the Syste m Informati on screen of t he Menu in terface, set the Ti m e Synch Method para meter to None , then press [Enter], then [S] (for S ave ). ■ In the Global config le vel of the CLI, execute no timesync . SNTP: V i ewing, Selecting, and Configuring SNTP Feature Default Me[...]

9-5 Time Protocols SNTP: Viewing, Selecting, and Configuring T able 9-1. SNTP Para meters Menu: V iewing and Configuring SNTP T o View , Enable, and Modify SNTP T ime Protocol: 1. From the Main Menu, select: 2. Switch Configuration ... 1. System Information SNTP Parameter Operation T ime Sync Method Used to select either SNTP , TIMEP , or None as t[...]

9-6 Time Protocols SNTP: Viewing, Selecting, and Configuring Figure 9-1. The System Information Screen (Default V alues) 2. Press [E] (for E dit ). The cursor moves to the System Name field. 3. Use [v] to move the cursor to the T ime Sync Method fiel d. 4. Use the Space bar to select SNTP , then press [v] once to display and move to the SNTP Mode f[...]

9-7 Time Protocols SNTP: Viewing, Selecting, and Configuring Note: This step replaces any pre v iously configured server IP address. If you will be using b ackup SNTP servers (requires use of the CLI), then refer to “SNTP Uni cast T im e Polling with Multiple SNTP Servers” on page 9-25. iii. Press [v] to move the cursor to the Server V ersi on [...]

9-8 Time Protocols SNTP: Viewing, Selecting, and Configuring CLI: V iewing and Configuring SNTP CLI Commands Described in this Section This section describes how to use the CLI to view , enable, and configure SNTP parameters. V iewing the Current SNTP Configuration For example, if you co nfigured the switch with SNTP as the time synchronization met[...]

9-9 Time Protocols SNTP: Viewing, Selecting, and Configuring Figure 9-4. Example of SNTP Configuration Wh en SNTP Is the Selected T ime Sync hronization Method In the factory-d efault configu ration (where Ti meP is the selected time synchronization method ), show sntp still lists the SN TP configuration eve n though it is not currently in use. For[...]

9-10 Time Protocols SNTP: Viewing, Selecting, and Configuring Figure 9-6. Example of Display Showin g IP A ddressing for All Configured T ime Servers and VLANs Configuring (Enabling or Disabling) the SNTP Mode Enabling the SNTP mode means to configur e it for ei ther broadcast or unicast mode. Remember t hat to run SNTP as t he switch’ s time syn[...]

9-11 Time Protocols SNTP: Viewing, Selecting, and Configuring Enabling SNTP in Broadcast Mode. Because the switch provides an SNTP polling interval (default: 720 seconds ), you need only these two commands for minimal SNTP broadcast configurati on: Syntax: timesync sntp Selects SNTP as the time synchronizat ion method . Syntax: sntp broadc ast Conf[...]

9-12 Time Protocols SNTP: Viewing, Selecting, and Configuring second or third server , you must u se the CLI. F or more on SNTP operation with multiple serv ers, refer to “SNTP Unicast T ime Polling with Mu ltiple SNTP Servers” on page 9-25. Syntax: timesync sntp Selects SNTP as the time synchronizat ion method. Syntax: sntp unicast Configures [...]

9-13 Time Protocols SNTP: Viewing, Selecting, and Configuring . Figure 9-8. Example of Configurin g SNTP for Unicast Operation If the SNTP server you specify uses SNTP version 4 or la ter , use the sntp server command to specify the correct versio n number . For exam ple, suppose you learned that SNTP version 4 was in use on th e server you spec if[...]

9-14 Time Protocols SNTP: Viewing, Selecting, and Configuring Changing the SNTP Poll Interval. For example, to change the po ll interval to 300 seconds: ProCurve(config)# sntp poll-interval 300 Changing the Priority . Y ou can choose the ord er in which config ured servers are polled for getting the ti me by setting the server priori ty . For examp[...]

9-15 Time Protocols SNTP: Viewing, Selecting, and Configuring Figure 9-10. Example of SNTP with T i me Synchronization Disabled Disabling the SNTP Mode. If you want t o prevent SNTP from bei ng used even if selected by timesync (or the Menu interface’ s T ime Sync Met hod param- eter), configure the SN TP mode as disabled. For example, if the swi[...]

9-16 Time Protocols TimeP: Viewing, Selecting, and Configuring T imeP: V iewing, Selecting, and Configuring T able 9-2. Timep Parameters T imeP Feature Default Menu CLI We b view the T imep time synchronization configuration n/a page 9-17 page 9-19 — select T imep as the time synchronization method TIMEP page 9-15 pages 9-21 ff. — disable time [...]

9-17 Time Protocols TimeP: Viewing, Selecting, and Configuring Menu: V iewing and Configuring T imeP T o View , Enable, and Modify t he T imeP Protocol: 1. From the Main Menu, select: 2. Switch Configuration ... 1. System Information Figure 9-12. The System Information Screen (Default V alues) Press [E] (for Edit ). The cursor moves to the System N[...]

9-18 Time Protocols TimeP: Viewing, Selecting, and Configuring ii. Enter the IP address of the T ime P server you want the switch to use for time synchronization. Note: This step replaces any previously configured T imeP server IP address. iii. Press [>] to move the cursor to the Pol l Interval field, then go to step 6. 5. In the Pol l Interval [...]

9-19 Time Protocols TimeP: Viewing, Selecting, and Configuring V iewing the Current T imeP Configuration Using different show commands, you can display either the full T imeP config- uration or a combined listing of all T imeP , SNTP , and VLAN IP addresses configured on the switch. For example, if you configure the switch with T imeP as the time s[...]

9-20 Time Protocols TimeP: Viewing, Selecting, and Configuring Figure 9-15. Example of Display Showin g IP A ddressing for All Configured T i me Servers and VLANs Configuring (Enabling or Disabling) the T imeP Mode Enabling the T imeP mode means to configure it f or either broadcast or un icast mode. Remember that to run T imeP as the switch’ s t[...]

9-21 Time Protocols TimeP: Viewing, Selecting, and Configuring Enabling T imeP in DHCP Mode. Bec ause the switch provides a T imeP polling interval (defaul t: 720 minutes) , you need only these two commands for a minimal T imeP DHCP conf iguration: For example, suppose: ■ T ime synchronization i s configur ed for SNTP . ■ Y ou want to: 1. V iew[...]

9-22 Time Protocols TimeP: Viewing, Selecting, and Configuring Enabling T imep in Manual Mode. Like DHCP mode, configuring TimeP for Manual mode enables T i meP . However , for manual operation, you must also specify the I P address of the T imeP ser ver . (The switch allows only one TimeP server .) T o enable the TimeP protocol: Note T o change fr[...]

9-23 Time Protocols TimeP: Viewing, Selecting, and Configuring Figure 9-17. Example of Configuring T imep for Manual Operation Changing the T imeP Poll Interval. This command lets you specify how long the switch waits between time po lling intervals. The default is 720 minutes and the range is 1 to 9999 minutes. (T his parameter is separate from th[...]

9-24 Time Protocols TimeP: Viewing, Selecting, and Configuring Figure 9-18. Example of T imeP with Time Synchronization Disabled Disabling the T imeP Mode. Disabling the T imeP mode means to configure it as disabled. (Disabling T imeP prevents the switch from using it as the time synchronization protocol, even if it is the selected T ime Sync Metho[...]

9-25 Time Protocols SNTP Unicast Time Polling with Multiple SNTP Servers SNTP Unicast T ime Polling with Multiple SNTP Servers When running SNTP unicast time polli ng as the time synchronizat ion method, the switch requests a time update fro m the server yo u configured with either the Server Address parameter in the menu interface, or the primary [...]

9-26 Time Protocols SNTP Messages in the Event Log Adding and Deleting SNTP Server Addresses Adding Addresses. As mentioned earlier , yo u can conf igure one SNTP server address using either the Menu interface or the CL I. T o configure a second and third address, you must us e the CLI. T o conf igure the remaining two addresses, you would do the f[...]

10-1 10 Port Status and Configuration Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Viewing Port Status and Configuring Port Parameters . . . . . . . . . . 10-3 Menu: Port Configuratio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 CLI: [...]

10-2 Port Status and Configuration Contents Configuring UDLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-32 Enabling UDLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-33 Changing the Keepalive Interval . . . . . . . . . . . . . . . . . . . . . . . . . 10-34 Changing the [...]

10-3 Port Status and Configuration Overview Overview This chapter describes how to view th e current port conf iguration and how to configure ports t o non-d efault settings, including ■ Enable/Disable ■ Mode (speed and duplex) ■ Flow Control ■ Broadcast Limit ■ Friendly P ort Names ■ Uni-directional L ink Detection (UDLD) V iewing Port[...]

10-4 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters T able 10-1. Status and Parameters for Each Port T ype Status or Parameter Description Enabled Ye s (default): The port is ready for a network conn ection. No: The port will not operate, even if properly connected in a network. Use this setting, for example, if [...]

10-5 Port Status and Configuration Viewing Port Status and Configuring Port Parameters — Continued From Previous Page — Gigabit Fiber -Optic Ports (Gigabit-SX, Gigabit-LX, and Gigabit-LH): • 1000FDx: 1000 Mbps (1 Gbps ), Full Duplex only • Auto (default): The port operates at 1000FDx and auto-negotiates flow control with the device connecte[...]

10-6 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Menu: Port Configuration From the menu interface, you can view and change the port configuration. Using the Menu T o V iew Port Con figuration. The menu interf ace dis- plays the configuratio n for ports and (if configured ) any trunk groups. From the Main Menu,[...]

10-7 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Using the Menu T o Configure Ports. Y ou can configure and view the port settings by using the menu. Note The menu interface uses the same sc re en for configuring both individual ports and port trunk groups. For i nformation on port tr unk groups, refer to Chapt[...]

10-8 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters CLI: Vi ewing Port Status and Configuring Port Parameters From the CLI, you can conf igure and view all port pa rameter settings and view all port statu s indicators. Port Status and Conf iguration Commands V iewing Port Status and Configuration Use the followin[...]

10-9 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Figure 10-3. Example of Show Interfac es Brief Command Listing Use the show interfaces config command t o view the po rt settings, as shown below . Figure 10-4. Example of a Sh ow Interfaces Config Comm and Listing The display option can be used to initiate th e [...]

10-10 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters For example: ProCurve# show interfaces display Figure 10-5. Example of show interfa ces display Command wi th Dynamically Updating Out put Customizing the Show Interfaces Command Y ou can create show commands displaying t he information that you want to see in [...]

10-11 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Columns supported are: Syntax: show interfaces cu stom [port-list] column-list Select the information that yo u want to display . Parameters include: ■ port name ■ type ■ vlan ■ intrusion ■ enabled ■ status ■ speed ■ mdi ■ flow Parameter Column[...]

10-12 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Figure 10-6. Example of the Custo m show interfaces Comma nd Y ou can specify the column width by en tering a colon after th e column name, then indi cating th e number of characters to display . In Figure 10-6 the Name column on ly displays the first four char[...]

10-13 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Note on Using Pattern Matching with the “Show Interfaces Custom” Command If you have included a pa tt ern matchi ng command t o search for a fie ld in the output of the show int custom command and t he show int custom command produces an erro r , the er ror [...]

10-14 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Operating Notes: ■ For each port on the switch, the co mmand provides a re al-time display of the rate at which data is received (Rx) and transmitted (Tx) in terms of kilobits per se cond (KBits/s), numbe r of packets pe r second (Pkt s/ s), and utilization ([...]

10-15 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Operating Notes: ■ The following inform ation is displa yed for each installe d transceiver: • Port number on which transceiver is installed. • T ype of transceiver . • Product number —Includes revision l etter , such as A, B, or C. If no revision lett[...]

10-16 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Note that in the ab ove syntax you can sub stitute an “ int ” for “ interface ”; that is: int < port-list > . The 10/100 aut o-negotiati on feature al lows a port to establish a li nk with a port at the other end at ei ther 10 Mbps or 100 Mbps, us[...]

10-17 Port Status and Configuration Viewing Port Status and Configuring Port Parameters Enabling or Disabling Flow Control Note Flow control is enabl ed by default on t h e downlink po rts. Y ou must enable flow control on the upl ink ports in a given lin k. Otherwise, flow control does not operate on the link, and ap pears as Off in the show inter[...]

10-18 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Figure 10-11. Exa mple Continued from Figure 10- 10 Figure 10-12. Exa mple Continued from Figure 10- 11 Configuring a Broadcas t Limit on the Switch Broadcast-Limi t on switches co ve r e d in t hi s g ui de is confi gured on a per -port basis. Y ou must be at [...]

10-19 Port Status and Configuration Viewing Port Status and Configuring Port Parameters ProCurve(config)#int B1 ProCurve(int B1)# broadcast-limit 1 Broadcast-Limit. For example, the following command en ables broadcast limitin g of 1 percent of the traffic rate on the se le cted port on the switch: ProCurve(int B1)# broadcast-limit 1 For a one Gbps[...]

10-20 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters ■ 100/1000-T xl modu le ports ■ 10/100/1000-T xl module ports Using the above ports: ■ If you connect a copper port using a straight- through cable on a switch to a port on another switch or hub that uses MDI-X ports, the switch port automatically operate[...]

10-21 Port Status and Configuration Viewing Port Status and Configuring Port Parameters The Auto-MD IX feat ures apply o nly to co pper port swi tches using twisted-pair copper Ethernet cables. For example, show interfaces config displays the following data wh en port A1 is configured for auto-mdix , port A2 is configured for mdi , and port A3 is c[...]

10-22 Port Status and Configuration Viewing Port Status and Configur ing Port Parameters Figure 10-13. Example of Displayi ng the Current MDI Config uration Figure 10-14. Example of Displaying th e Current MDI Operating Mode W eb: Viewing Port Status and Confi guring Port Parameters In the web browser interface: 1. Click on the Configuration tab. 2[...]

10-23 Port Status and Configuration Using Friendly (Optional) Port Names Using Friendly (Optional) Port Names This feature enables yo u to assign alphanume ric port names of your ch oosing to augment au tomatically assigne d numeric por t names. This means yo u can configure meaningful port names to make it easie r to identify the source of informa[...]

10-24 Port Status and Configuration Using Friendly (Optional) Port Names ■ T o retain friendly por t names across reboot s, you must save the current running-con figuration to the sta rtup-config fi le after ente ring the friendly port names. (In the CLI, use the write memory command.) Configuring Friendly Port Names Syntax: interface < port-l[...]

10-25 Port Status and Configuration Using Friendly (Optional) Port Names Configuring the Sa me Name for Multiple Ports. Suppose that you want to use ports A5 through A8 as a trunked l ink to a server used by a drafting group. In this case you might configure ports A5 through A8 with the name “Draft-Server:T runk”. Figure 10-16. Example of C onf[...]

10-26 Port Status and Configuration Using Friendly (Optional) Port Names Syntax: show name [ port-list ] Lists the friendly port name with its corresponding port number and port type. The show name command without a port list shows this data for all ports on the switch. For example: Figure 10-17. Example of Fr iendly Port Name Data for All Ports on[...]

10-27 Port Status and Configuration Using Friendly (Optional) Port Names Syntax: show interfa ce < port-numbe r > Includes the friendly port name wi th the port’ s traffic statistics listing. For example, if you configure port A1 with the name “O’Connor_10.2 5.101.43”, the show interface output for this por t appears similar to the fo[...]

10-28 Port Status and Configuration Using Friendly (Optional) Port Names For example, if you co nfigure port A1 with a friendly po rt name: Figure 10-20. Example Listing of the Startup-Config File with a Friendly Port Name Co nfigured (and Saved) This command seque nce saves the friendly port name for port A1 in the startup- config file. The n ame [...]

10-29 Port Status and Configuration Using Friendly (Optional) Port Names Configuring T ransceivers and Modules That Haven’t Been Inserted T ransceivers Previously , a port ha d to be va lid and verif ied for the swit ch to allow it to be configured. T ransceivers are removable ports and considered invalid when not present in the switch, so they c[...]

10-30 Port Status and Configuration Using Friendly (Optional) Port Names For example: ProCurve(config)# no module 3 Note This does not change how hot-swap works. Operating Notes The following restrictions apply: ■ The slot being cleared must be empty ■ There was n o module present in the slot since the last boot ■ If there was a module pr ese[...]

10-31 Port Status and Configuration Uni-Directional Link Detection (UDLD) Uni-Directional Link Detection (UDLD) Uni-directional Lin k Detection (UDLD) monit ors a link between two ProCurve switches and blocks the ports on both en ds of the link if the link fails at any point between the two devices. This featur e is particularly useful for detectin[...]

10-32 Port Status and Configuration Uni-Directional Link Detection (UDLD) connected ports. UDLD-enabled port s; however , will prevent traffic from being sent across a bad link by blocking the ports in the event th at either the individual transmitter or receiver for that connection fails. Ports enabl ed for UDLD ex change heal th-check packets onc[...]

10-33 Port Status and Configuration Uni-Directional Link Detection (UDLD) Enabling UDLD UDLD is enabled on a per port basis. For example, to enab le UDLD on por t a1, enter: T o enable the feature on a trunk group, enter the appropri ate port range. For example: Note When at least one port is UDLD-enable d, the switch will forwa rd out UDLD packets[...]

10-34 Port Status and Configuration Uni-Directional Link Detection (UDLD) Changing the Keepalive Interval By default, ports en abled for UDLD send a link health-check packe t once every 5 seconds. Y ou can change th e i nterval to a value from 10 – 100 dec iseconds, where 10 is 1 second, 11 is 1.1 seconds, a nd so on. For exampl e, to change the [...]

10-35 Port Status and Configuration Uni-Directional Link Detection (UDLD) ■ T o re-assig n a VLAN ID, re-e nter the command with the new VLAN ID number . The new command will o verwrite the previous command setting. ■ When configuring UDLD for tagged ports, you may receive a warning message if there are any inconsistenc ies with the port’ s V[...]

10-36 Port Status and Configuration Uni-Directional Link Detection (UDLD) T o di splay detailed U DLD informatio n for specific ports, enter th e show link- keepalive statistics comma nd. For example: Figure 10-23. Example of Show Lin k-Keepalive Statistics Co mmand T o clear UDLD statistics, enter the following command: ProCurve# clear link-keepal[...]

10-37 Port Status and Configuration Uni-Directional Link Detection (UDLD) Configuration W arnings and Event Log Messages W arning Messages. The following tab le shows the warning messages that may be issued and their possible causes, when UDLD is c onfigured for tagged ports. T able 10-3. Warning Messages caused by configuring UDLD fo r T ag ged Po[...]

11-1 11 Port T runking Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3 Port Trunk Features an d Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5 Trunk Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5 Menu: Vie[...]

11-2 Port Trunking Overview Overview This chapter describes creating and modifying port trunk groups. This includes non-protocol trunks an d LACP (802.3ad) trun ks. Port Status and Conf iguration Feature s Port trunking allows you t o assign up to eight physical links to one l ogical link (trunk) that functio ns as a single, higher -speed link pro [...]

11-3 Port Trunking Overview Port Connecti ons and Config uration: All port trunk links must be po int- to-point connections between a sw itch and anothe r switch, router , server , or workstation config ured for port trunking. No intervening, non-trun king devices are allowed. It i s important to note that po rts on both end s of a port trunk group[...]

11-4 Port Trunking Port Trunk Features and Operation Port T runk Features and Operation T he s w i t c he s covered in this guide of f e r th e s e o p ti o n s f o r p o r t t ru n k i n g : ■ LACP: IEEE 802.3ad—page 11-18 ■ T runk: Non- Protocol—page 11-26 Up to 60 trunk groups are su pported on th e s w i t c he s covered in this guide. [...]

11-5 Port Trunking Trunk Configuration Methods ProCurve(config) int c1-c4 lacp active Note that the preceding ex ample works if the ports are not already operating in a trunk. T o change the LACP option on ports already operati ng as a trunk, you must first remo ve them from the trun k. For example, if ports C1 - C4 were LACP-active and operating i[...]

11-6 Port Trunking Trunk Configuration Methods T able 11-2. T runk Conf iguration Protocols Protocol T runking Options LACP (802.3ad) Provides dynamic and static LACP trunking options. • Dynamic LACP — Use the switch-negotiated dy namic LACP trunk when: – The port on the other end of the trunk link is configured for Active or Passive LACP . ?[...]

11-7 Port Trunking Trunk Configuration Methods T able 11-3. General Operating Ru les for Port T ru nks Media: For proper trunk operation, all ports on both ends of a trunk group must have th e same media type and mode (speed and duplex). (For the switches cover ed in this guide, ProCurve recommends leaving the port Mode setting at Auto or , in netw[...]

11-8 Port Trunking Trunk Configuration Methods Spanning T ree: 802.1D (STP) and 802.1w (RSTP) Spanning T ree operate as a global setting on the switch (with one instance of Spanning T ree per switch). 802.1s (MSTP) Spanning T r ee operates on a per -instance basis (with multiple instances allowed per switch). For each Spanning T ree instance, you c[...]

11-9 Port Trunking Menu: Viewing an d Configuring a Static Trunk Group Menu: V iewing and Configuring a Static T runk Group Important Configure port trunki ng before you connect the trunked links to anot her switch, routing switch, or server . Otherwise, a broad cast storm could occu r . (If you need to connect the ports before configur ing them fo[...]

11-10 Port Trunking Menu: Viewing an d Configuring a Static Trunk Group • For proper tr unk operation, all ports i n a trunk must have the same media type and mode (such as 10/100TX set to 100FDx, or 100FX set to 100FDx). The flow control settings must also be the same for all ports in a given trunk. T o verify thes e settings, refer t o “Viewi[...]

11-11 Port Trunking CLI: Viewing and Configuring Port Trunk Groups 8. Connect the trunked ports on the switch to the correspondi ng ports on the opposite device. If you previousl y disabled any of the trunked ports on the switch, enab le them now . (R efer to “V iewing Port Status and Configuring Port Parameters” on page 10-3.) Check the Event [...]

11-12 Port Trunking CLI: Viewing and Configurin g Port Trunk Groups Using a port list specifies, for sw itch ports in a static trunk group , only the ports you want to vi ew . In this case, the command specifies ports A5 through A 7 . H o w e v e r, b e c a u s e p o r t A 6 i s n o t i n a static trunk group , it does no t appear in the resultin g[...]

11-13 Port Trunking CLI: Viewing and Configuring Port Trunk Groups Listing Static LACP and Dynamic LACP T runk Data. In the followin g example, ports A1 and A2 have been previously con figured for a static LACP tr unk. (For more on the “Active” parameter , see table 11-5 on page 11-21.) Figure 11-8. Example of a Show LACP Listing (For a descrip[...]

11-14 Port Trunking CLI: Viewing and Configurin g Port Trunk Groups Figure 11-9. Example of a Dynamic LACP T runk w ith One Standby Link Using the CLI T o Configure a Static or Dynamic T runk Group Important Configure port trun king before y ou connect the trunked links between switches. Otherwise, a broadcast storm could occur . (If you need to co[...]

11-15 Port Trunking CLI: Viewing and Configuring Port Trunk Groups Configuring a Static T runk or Static LACP T runk Group. This example uses port s C4 - C6 to create a non-protocol static trunk gro up with the group n ame of Tr k 2 . ProCurve(config)# trunk c4-c6 trk2 trunk Removing Ports from a Stati c T runk Group. This command removes one or mo[...]

11-16 Port Trunking CLI: Viewing and Configurin g Port Trunk Groups Figure 11-10. Example of Criteria for Automat ically Forming a Dynamic LACP T runk This example uses ports C4 and C5 to enable a dynamic LACP trunk group. ProCurve(config)# interface c4-c5 lacp active Removing Ports from an Dynamic LACP T runk Group. T o remove a port from dynamic [...]

11-17 Port Trunking Web: Viewing Existing Port Trunk Groups Caution Unless spanning tree is running on your netw ork, removing a port from a trunk can result i n a loop . T o help preven t a broadcast storm when you remove a port from a trunk whe re spanning tree is not in use, P roCurve recommends that you first disabl e the port or disconnect th [...]

11-18 Port Trunking Trunk Group Operation Using LACP T runk Group Operation Using LACP The switch can automat ically configur e a dynamic LACP trunk gr oup or you can manually configure a static LACP trunk group. Note LACP requires full -duplex (FDx) lin ks of the same media ty pe (10/100Base -T , 100FX, etc.) and the same speed, and en forces spee[...]

11-19 Port Trunking Trunk Group Operation Using LACP T able 11-4. LACP T runk T yp es LACP Port T runk Configuration Operation Dynamic LACP This option automatically establishes an 802.3ad-compliant trunk group, with LACP for the port T ype parameter and Dy n X for the port Group name, where X is an automatic ally assigned value from 1 to 60, depen[...]

11-20 Port Trunking Trunk Group Operation Using LACP Static LACP Provides a manually configured, st atic LACP trunk to acco mmodate these conditions: • The port on the other end of the trunk link is configured for a static LACP trunk. • Y ou want to configure non-default spanning tree or IGMP parameters on an LACP trunk group. • Y ou want an [...]

11-21 Port Trunking Trunk Group Operation Using LACP Default Port Operation In the default configuration, LACP is di sabled for al l ports. If LACP is not configured as Active on at least one end of a link, then the p ort does not t ry to detect a trunk configur ation and operates as a standard, untrunked port. T able 11-5 lists the elements of pe [...]

11-22 Port Trunking Trunk Group Operation Using LACP LACP Notes and Restrictions 802.1X (Port-Based Access Contro l) Configu red on a Port. To m a i n - tain security , LACP is n ot allowed o n ports configured for 802.1X authenticator operation. If you co nfigur e port security on a port on w hich LACP (active or passive) is configured, the switch[...]

11-23 Port Trunking Trunk Group Operation Using LACP ProCurve(config)# int a17 lacp passive Error configuring port A17: LACP and port security cannot be run together. ProCurve(config)# T o restore LACP to the port, you must remove port security and re-enable LACP active or pa ssive. Changing T runking Methods. T o convert a trunk from static to dyn[...]

11-24 Port Trunking Trunk Group Operation Using LACP Figure 11-11. Block ed Ports with LACP ■ If there are ports that you do not want on the default VLAN, ensure that they cannot become dynamic LACP trunk members. Otherwise a traf fic loop can unexpectedly occur . For example: Figure 11-12. A Dynamic LACP T runk Forming in a VLAN Can Cause a T ra[...]

11-25 Port Trunking Trunk Group Operation Using LACP Spanning T ree and IGMP . If Spanning T ree and/or IG MP is enabl ed in the switch, a dynamic LACP trunk op erates only with the default setti ngs for these features and does not appear in th e port listings for these features. Half-Duplex and/or Dif ferent Port Speeds Not Allowed in LACP T runks[...]

11-26 Port Trunking Trunk Group Operation Using the “Trunk” Option T runk Group Operation Using the “T runk” Option This method creat es a trunk grou p that operat es independently of speci fic trunking protocol s and does not use a protocol ex change with the device on the other end of the trunk. W ith this ch oice, the switch simp ly uses[...]

11-27 Port Trunking How the Switch Lists Trunk Data How the Switch Lists T runk Data Static T runk Grou p: Appears in the menu interface and t he output from the CLI show trunk and show interfa ces commands. Dynamic LACP T runk Group: Appears in the output f rom the CLI show lacp command. Outbound T raffic Distribution Across T runked Links The two[...]

11-28 Port Trunking Outbound Traffic Distribution Across Trunked Links The load-balancing is done on a per co mmunication basis. Otherwise, traffic is transmitted across the same path as show n in figure 11-13. That is, if Client A attached to Switch 1 sends five packet s of data to Server A attached to Switch 2, the same link is used to send a ll [...]

11-29 Port Trunking Outbound Traffic Distribut ion Across Trunked Links T able 11-6. Example of Link Assignments in a T runk Group (SA/DA Distribution) Because the am ount of traffi c coming from or going to various nodes in a network can vary widely , it is possible f or one link in a trunk group to be fully utilized while other links in th e same[...]

12-1 12 Port T raffic Controls Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Jumbo Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

12-2 Port Traffic Controls Overview Overview This chapter includes: ■ Jumbo Frames: Enables ports operating at 1 Gbps or 10 Gb ps speeds to accept inbound frames of up to 92 20 bytes w hen configur ed for jumbo traffic. Jumbo Frames The Maximum T ransmission Unit (MTU) is the maximum size I P frame the switch can receive for Layer 2 frames in bou[...]

12-3 Port Traffic Controls Jumbo Frames Jumbo VLAN: A VLAN configured to allow inb ound jumbo traffic. All ports belonging t o a jumbo and operating at 1 Gbps or higher can receive jumbo frames from external devices. If the switch is in a meshed domain, then all meshed ports (operating at 1 Gbps or higher) on the switch will accept jumbo traffic fr[...]

12-4 Port Traffic Controls Jumbo Frames Configuring Jumbo Frame Operation Overview 1. Determine the VLAN memb ership of the ports or trun ks through which you want the switch to accept inboun d jumbo traffic. For operation w ith GVRP enable d, refer to the GVRP top ic under “Operating Rules”, abo ve. 2. Ensure that the ports through which you w[...]

12-5 Port Traffic Controls Jumbo Frames V iewing the Current Jumbo Configuration Figure 12-1. Example Listing of St atic VLANs T o Show Jumbo Status Per VLAN Syntax: show vlans Lists the static VLANs configured on the swit ch and includes a Jumbo column to indica te whic h VLANs are configured to support inbound jumbo traffic. All ports belonging t[...]

12-6 Port Traffic Controls Jumbo Frames Figure 12-2. Example of Listing the VLAN Memberships for a Range of Ports Figure 12-3. Example of Listing the Port Membership and Jumb o Status for a VLAN Syntax: show vlans < vid > This command shows port membership and jumbo configuration for the specified < vid > . Indicates which stat ic VLANs[...]

12-7 Port Traffic Controls Jumbo Frames Enabling or Disabling Jumbo T raffic on a VLAN Configuring a Maximum Frame Size Y ou can globally set a maximum fram e size for Jumbo frames that will sup port values from 1518 bytes to 9216 bytes for untagged frame s. SNMP Implementation Jumbo Maximum Frame Size. The maximum frame size for Jumbos is supporte[...]

12-8 Port Traffic Controls Jumbo Frames Jumbo IP MTU. The IP MTU for Jumbos is suppor ted with the following propr ietary MIB object: hpSwitchIpMTU OBJECT -TYPE This is the value o f the global Jumbos IP MTU (o r L3 MTU) supporte d by the switch. The default value is set to 9198 bytes (a value that is 18 bytes less than the largest possible maximu [...]

12-9 Port Traffic Controls Jumbo Frames Operating Notes for Ju mbo T raffic-Handling ■ ProCurve does not reco mmend configur ing a voice VLAN to accept jumbo frames. V oice VLAN frames are typically small, and allowi ng a voice VLAN to accept jumbo frame traffic can de grade the voice transmission perfor - mance. ■ Y ou can configure the defaul[...]

12-10 Port Traffic Controls Jumbo Frames If there are security concerns with grouping the ports as shown for V LAN 300, you can either use source-port filtering to block unwanted traffic paths or create separate jumbo VLANs, one for ports 6 and 7, and another for ports 12 and 13. ■ Outbound Jumbo T r af fic. Any port operating at 1 Gbps or higher[...]

12-11 Port Traffic Controls Jumbo Frames T roubleshooting A VLAN is configured to allow jum bo frames, but one or more ports drops all inbound j umbo frames. The port may not be operating at 1 giga- bit or higher . Regardless of a port’ s config uratio n, if it is actually operating at a speed lower than 1 gigabit , it drops inbound jumbo frames.[...]

13-1 13 Configuring for Network Management Applications Contents Using SNMP Tools To Manage the Switch . . . . . . . . . . . . . . . . . . . . . . 13-3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3 SNMP Management Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

13-2 Configuring for Network Manageme nt Applications Contents LLDP (Link-Layer Discovery Protocol) . . . . . . . . . . . . . . . . . . . . . . . 13-36 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-37 General LLDP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

13-3 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Using SNMP T ools T o Manage the Switch Overview Y ou can manage the switch via SN MP from a network management statio n running an applic ation such as ProCurve Manager (PCM) or ProCurve Ma nager Plus (PCM+). For more on PCM and PCM +, visit the ProC urve Ne[...]

13-4 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch VLAN feature, refer to th e section titled “The Se cure Management VLAN” in the “Static Virtual LANs (VLAN s)” chapter of th e Advanced T raffic Management Guide f or your swit ch.[...]

13-5 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch SNMP Management Features SNMP management features on the switch include: ■ SNMP version 1, version 2c, or version 3 over IP ■ Security via configuration of SNMP communities (page 13 -12) ■ Security via authentica tion and privacy for SNMP V ersion 3 acc[...]

13-6 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch If you want to restrict acce ss to one or more specifi c nodes, you can use the switch’ s IP Auth orized Mana ger feature. (R efer to the Access Security Guide for your sw itch.) Caution For ProCurve Manager (PCM) version 1.5 or earlier (or any T opT ools [...]

13-7 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch SNMP V ersion 3 Commands SNMP version 3 (SNMPv3) adds so me new commands t o the CLI for configuring SNMPv3 functi ons. T o enable SMNPv3 operation on the switch, use the snmpv3 enable command. An ini tial user entry will be gene rated with MD5 authentication[...]

13-8 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Enabling SNMPv3 The snmpv3 enable command allows the switch to: ■ Receive SNMPv3 messages. ■ Configure initial u sers. ■ Restrict non-version 3 message s to “read only” (optional). Figure 13-1 shows an example of how to use the snmpv3 enable comman[...]

13-9 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch 1. Configure users in the User T able with the snmpv3 user command. T o view the list of co nfigured us ers, enter the show snmpv3 user command (see “Adding Users” on page 13-9). 2. Assign users to Se curity Groups ba sed on their sec urity model with the[...]

13-10 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMPv3 User Commands Listing Users. T o displa y the management stat ions configured to acc ess the switch with SNMPv3 and view the auth entication and privacy protocols that each station uses, enter the show snmpv3 user command. Syntax: show snmpv3 user Th[...]

13-11 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Assigning Users to Groups. Then you must set the group access level for the user by assigning the user to a group. This is done with the snmpv3 group command. For mo re details on the MI Bs acc ess for a given group refer to “Group Access Levels” on page[...]

13-12 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Group Access Levels The switch suppor ts eight predefined group access levels. There are four levels for use with version 3 users and four are use d for access by version 2c or version 1 management applications. Each view allows you to view or modify a diff[...]

13-13 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Figure 13-4 shows the assigning of th e Operator community on MgrStation1 to the CommunityOperatorReadW rite group. Any other Oper ator only has an access level of CommunityOperatorReadOnly Figure 13-4. Assigning a Community to a Group Access Level Syntax: [[...]

13-14 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP Community Features Use SNMP communities to restrict acce ss to the switch by SNMP management stations by adding, edit ing, or deleti ng SNMP communiti es. Y ou can configure up to five SNMP communit ies, each with either an operator -level or a ma nage[...]

13-15 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Figure 13-5. The SNMP Communiti es Screen (Default Values) 2. Press [A] (for Add ) to display the following screen: Figure 13-6. The SNMP Add or Edit Screen Need Help? If you need informat ion on the options in each field, press [Enter] to move the cursor to[...]

13-16 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch CLI: V iewing and Configuring SNMP Community Names Listing Community Names and V alues. This command lists the data for currently configured SNMP community na mes (along with trap receive rs and the setting for authentication traps — refer to “SNMP Noti[...]

13-17 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Configuring Community Na mes and V alues. The snmp-server command enables you to add SNMP communities wi th either default or spec ific access attributes, and to delete specific communities. For example, to add th e following communities: ProCurve(config)# s[...]

13-18 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP Notifications T he s w i t c h e s covered in this guide s u p p o r t : ■ SNMP version 1 or SNMP version 2c traps ■ SNMPv2c informs ■ SNMPv3 notific ation process, including t raps This section describes how to config ure a switch to send networ[...]

13-19 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch ■ Advance T raffic Management Guide: • Loop protection • Spanning T ree (STP , RSTP , MSTP) ■ Access Security Guide: • MAC lockdown • MAC lockout • Uni-Direct ional Link Dete ction (UDLD) General Steps for Configuring SNMP Notifications T o con[...]

13-20 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMPv1 and SNMPv2c T raps T he s w i t c h e s covered in this guide s u p p o r t t h e f o l l o w i ng f u n c t i o na li t y f ro m earlier SNMP versions (SNMPv1 and SNMPv2c): ■ T rap receivers: A trap receiver is a management st ation to which the s[...]

13-21 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch T able 13-1. Security Levels for Event Log Messages Se nt as T raps Syntax: snmp-server host < ipv4-addr | ipv6-addr > < community name > Configures a destination ne twork management station to receive SNMPv1/v2c traps, and (optionally) event log[...]

13-22 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch For example, to configur e a trap receiver in a co mmunity named "red-team" with an IP address of 10.28.227.130 to receive only "critical" event log messages, you can enter the following comma nd: ProCurve(config)# snmp-server host 10.28[...]

13-23 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Note The retries and timeout values are not u sed to sen d trap requ ests. T o verify the configuration of SNMPv2c informs, enter the show snmp-server command: Figure 13-8. Display of SN MPv2c Inform Config uration ProCurve(config)# show snmp-se rver SNMP Co[...]

13-24 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Configuring SNMPv3 Notifications The SNMPv3 not ificatio n process allows messa ges that are passed via SNMP between the switch and a network mana gement station to b e authen ticated and encrypted. T o configure SNMPv3 notifi cations, foll ow these steps: [...]

13-25 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch 5. Configure the target address of the SNMPv3 managem ent station to whi ch SNMPv3 informs and trap s are sent by entering the snmpv3 targetaddress command. Syntax: [no] snmpv3 targetad dress < ipv4-addr | ipv6-addr> < name > Configures the IPv4 [...]

13-26 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch 6. Create a configuratio n re cord for the tar get address with the snmpv3 params command. Syntax: [no] snmpv3 targetad dress < ipv4-addr | ipv6-addr> < name > [timeout < value > ] (Optional) T ime (in millisecond increments) allowed to re[...]

13-27 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch An example of how to configure SNMPv3 notification i s shown here: Figure 13-9. Example of an SN MPv3 Notification Configu ration Managing Network Security Notifications By default, a switch is enab led to send the SNMP no tifications listed in “Supported [...]

13-28 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch T o ena ble or disabl e notification /traps for network security failures and othe r security events, enter the snmp-server enable traps command. T o determine the spe cific cause of a secu rity event, check th e event l og in the console interface to see w[...]

13-29 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Figure 13-10. Display of Config u red Network Security Notifica tions Enabling Link-Change T raps By default a switch is enabled to send a trap when the link state on a port changes from u p to down (lin kDown) or dow n to up (linkUp ). T o re configure the [...]

13-30 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Configuring the Source IP Addr ess for SNMP Notifications The switch uses a n interface IP address as the source IP address in IP headers when sending SNMP notificatio ns (traps and informs) or responses to SNMP requests. For multi-nette d interfaces, the s[...]

13-31 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch T o configure the switc h to use a specif ied source IP address in generat ed trap PDUs, enter the snmp-server trap-sou rce command. Notes When you use the snmp-server response-source and snmp-server trap-source commands, note t he following behavi or: ■ T[...]

13-32 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Figure 13-11. Display of S ource IP Address Configuration Displaying SNMP Notification Configuration Use the show snmp-server command to displ ay the curre ntly conf igured: ■ Management stations (trap receivers) ■ Settings for networ k security not ifi[...]

13-33 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch In the follow in g example, the show snmp-server command output shows th at the switch has been configured to send SNMP traps and notifi cations to management stations that belong to th e “public”, “red- team ”, and “blue-te am” communities. Figu[...]

13-34 Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Configuring Listening Mode For switches that have a se parate out-of-band management port, you can specify whether a configured SNMP serv er listens for SNMP queries over the out-of-ban d management in terf ace, the data interface, or both. By default, the [...]

13-35 Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Advanced Management: RMON The switch supports RMON (Rem ote Monitoring) on all connected network segments. This allows for tro ubleshooting an d optimizing yo ur network. The followi ng RMON groups are supported: ■ Ethernet Statistics (except the numbers o[...]

13-36 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) LLDP (Link-Layer Discovery Protocol) T o standardize device discovery on al l ProCurve switches, L LDP will be implemente d while offering limited read -only support for CDP a s documented in this manual. For the latest informatio n on your switch model, con[...]

13-37 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) LLDP-MED (LLDP Media Endpoint Discovery): Provides an extension to LLDP and is designed to support V oIP de ployments. Note LLDP-MED is an extension for LLDP , an d the sw itch requires that LLDP be enabled as a prerequisite to LLDP-MED operation. An SNMP uti[...]

13-38 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) LLDP Neighbor: An LLDP device that is either directly c onnected to another LLDP device or co nn ected to that device by another , non-LLDP Layer 2 device (such as a hub) Note that an 802.1D-co mpliant switch does not forward LLDP data packets even if it is [...]

13-39 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) TL V (T ype-Length-V alue): A data unit t hat includes a data type field, a data unit length fiel d (in bytes), an d a field cont aining the actual data the unit is designed to carry (as an alphanumeric string, a bitmap, or a subgr oup of information ). Some [...]

13-40 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Configuration Options Enable or Disable LLDP on the Switch. In the default configuratio n, LLDP is glob ally enabled on the sw itch. T o prevent transmission or receipt of LLDP traffic, you can disable LLDP operat ion (page 13-40) Enable or Disable LLDP-MED.[...]

13-41 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) SNMP Notification. Y ou can enable the switch to send a notification to any configured SNMP trap receiver(s) wh en the swi tch detects a remote LLDP data change on an LLDP-e nabled port (page 13-50 ). Per -Port (Outbound) Data Options. The following table lis[...]

13-42 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Remote Management Address. The switch always includes an IP address in its LLDP advertisements. This can be either an address selected by a default process, or an address conf igured for in clusion in ad ve rtisements. Refer to “IP Address Advertisements?[...]

13-43 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) ■ RFC 2737 (Entity MIB) ■ RFC 2863 (Interfaces MIB) ■ ANSI/TIA-1057/D6 (LLDP-MED; refer to “LLDP-MED (Media-Endpoint- Discovery)” on page 1 3-55.) LLDP Operating Rul es (For additional information sp ecific to LLDP- MED operation, refer to “LLDP- [...]

13-44 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Spanning-T ree Blocking. Spanning tree does no t prevent LLDP packet transmission or receipt on STP-bl ocked links. 802.1X Blocking. Po rts blocked by 802. 1X operation do not al low transmission or recei pt of LLDP packet s. Configuring LLDP Operation In th[...]

13-45 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) For exampl e, show lldp config produces the following display when the switch is in the default LLDP configuration : Figure 13-13. Example of Viewing the General LLDP Configuration Displays the LLDP global configuration, LLDP port statu s, and SNMP notificati[...]

13-46 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Displaying Port Confi guration D etails. This command displ ays the port- specific configurat ion, including. Figure 13-14. Example of Per-Port Configuration Display Configuring Global LLDP Packet Controls The commands in this section configur e the aspects [...]

13-47 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) ■ Add entries to its neighbors ta ble based on data read from incoming LLDP advertisements. For example, to disable LLDP on the switch: ProCurve(config)# no lldp run Changing the Packet T ransmission Interval. This interval controls how often active po rts [...]

13-48 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Changing the T ime-to-Live for T ransmitted Advertisements. The T ime-t o-Live value (in second s) for all LLDP advertisements transmitted from a switch is controlled by the switch that generate s the advertisement, and determines how long an LLDP neighbor r[...]

13-49 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) For example, to change the delay-inter val from 2 seconds to 8 sec onds when the refresh-interval is at the default 30 seconds, yo u must first set th e refresh- interval to a minimum of 32 seconds (32 = 4 x 8). Figure 13-15. Example of Changin g the T ransmi[...]

13-50 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) delay interval delays the port’ s ability to re initialize and generate LLDP traffic following an LLDP disable/enable cycle. For example, the following comma nd changes the reinitiali zation delay interval to fiv e seconds: ProCurve(config)# setmib lldprei[...]

13-51 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Changing the Minimum Interval for Succe ssive Data Change Notifications for the Same Ne ighbor . If LLDP trap notificati on is enabled on a port, a rapid succession of changes in LLDP inf ormation recei ved in adverti sements from on e or more neighb ors can [...]

13-52 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Configuring Basic LLDP Per - Port Advertisement Content In the defa ult LLDP conf iguration, outbound advertisem ents from each p ort on the switch includ e both mandat ory and optional data. Mandator y Data. An active LLDP port on the switc h always include[...]

13-53 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) For example, if port 3 belongs to a subn etted VLAN that includes an IP address of 10.10.10.100 and you wanted port 3 to use this secondary address in LLDP advertisements, you would need to exec ute t he fo llowing command: ProCurve(config)# lldp config 3 ipA[...]

13-54 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) For example, if you want ed to exclude the system name TL V from the outbound LLDP adverti sements for all p orts on a switch, you woul d use this command: ProCurve(config)# no lldp config 1-24 basicTlvEnable system_name If you later decided to reinstat e th[...]

13-55 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) As mentioned ab ove, an SNMP net work managem ent applicatio n can be used to compare the port speed and duplex data configured in the switch and advertised by the LLDP endpoint. Y ou can also use the CLI to di splay this information. For more on us ing the C[...]

13-56 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) ■ Power over Ethernet (PoE) status and troubleshooting support via SNMP ■ support for I P telephony network troubleshooti ng of call quality issues via SNMP This section describ es how to configur e and use LLDP-MED featur es in the switches to support V[...]

13-57 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) ■ able to use th e following network po l icy elements configured on the client port •v o i c e V L A N I D • 802.1p (Layer 2) QoS • Diffserv codepoint (DSCP) (Layer 3) QoS ■ discover and advertise device locat ion da ta learned from the switch ■ [...]

13-58 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) ■ Class 3 (Communication Devices): These devices are typically IP phones or end-user devices that otherwise support IP media and offer all Class 1 and Class 2 features, plus location id en tification and emergency 911 capability , Layer 2 s witch support, [...]

13-59 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Note T opology change notifications pro vide one method for monitoring system activity . However , because SNMP normally employs UD P , which does not guarantee datagram delivery , topolog y change notifi cation should no t be relied upon as th e sole method [...]

13-60 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) LLDP-MED Fast Start Control Advertising Device Ca pability , Network Policy , PoE Status and Location Data The medTlvE nable option on the switch is enab led in the defa ult configurat ion and supports t he following L LDP-MED TL Vs: ■ LLDP-MED capa biliti[...]

13-61 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Note LLDP-MED operat ion requires the macphy_ config TL V subelement—e nabled by default—that is optional for IEEE 802.1AB LLDP operation. Refer to the dot3TlvEnable macphy_ config command on page 13-55. Network Policy Advertisements. Network policy adver[...]

13-62 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Notes A codepoint must have an 802.1p priority before you can configure it for use in prioritizi ng packets by VLAN-ID. If a co depoint you want to use shows No Override in the Prio rity column of the DSCP po licy table (displ ay with show qos- dscp map , th[...]

13-63 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Configuring Location Data for LLDP-MED Devices Y ou can configure a switch port to advert ise location data f or the switch i tself, the physical wall-ja ck location of the endpoint (recommended), or the location of a DHCP server supporting th e switch and/or[...]

13-64 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Syntax: [ no ] lldp config < p ort-list > medPortLo cation < Address-T ype > Configures location o r emergency c all data the switc h advertises per port in the location_id TL V . This TL V is for use by LLDP- MED endpoints empl oying location-ba[...]

13-65 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) — Continued — T ype/V alue Pairs ( CA-TYPE and CA-V ALUE ): This is a series of data pairs, each co mposed of a location data “type” specifier and the co rresponding location data for that type. That is, the first value in a pair is expected to be the[...]

13-66 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Configuring Coordinate-Based Locations. Latitude, longitude, and altitude data can be configured per s witch port using an SNMP management application. For more informat ion, refer to the document ation provid ed with the application. A further sour ce of in[...]

13-67 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) T able 13-4. Some Location Codes Used in CA-TYPE Fields* Example of a Location Configuration. Suppose a system operator wanted to configure the following in formatio n as the civic addre ss for a telephone connected to her company’ s ne twor k through port [...]

13-68 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Figure 13-17. Example of a Ci vic Address Configuration Displaying Advertisement Data Command Page show lldp info local-device below walkmib lldpXdot3LocPortOperMauT ype show lldp info remote-device 13-71 walkmib lldpXdot3RemPortAutoNegAdvertised Cap show ll[...]

13-69 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Displaying Switch Informat ion A vailable for Outbound Advertisements These commands display the current switch informati on that will be used to populate outbo und LLDP advertisements. For example, in the default configuration, the switch information current[...]

13-70 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Figure 13-18. Example of Displayin g the Global and Per-Port Information Available for Outbound Advertisements Figure 13-19. Example of the Def ault Per -Port Information Content fo r Ports 1 and 2 Displaying the Current Port Spee d and Duplex Config uration[...]

13-71 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) an LLDP-MED endpoint, refer to “Dis playing the Current Port Speed and Duplex Configurat ion on a Sw itch Port” on page 13-70. Displaying Advertisem ents Currently in the Neighbors MIB. These commands displ ay the cont ent of the inboun d LLDP advertiseme[...]

13-72 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Figure 13-20. Example of a Gl obal Listing of Discovered Devices Figure 13-21. Example of an LLLD P-MED Listing of an Advertisement Received Fr om an LLDP-MED (V oIP T ele phone) Source ProCurve# show lldp info remote- device LLDP Remote Devices Information [...]

13-73 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Displaying LLDP Statistics LLDP statistics are availabl e on both a global and a per -port levels. Rebooting the switch resets the LLDP statisti cs co unters to zero. Disa bling the transmit and/or receive capability on a port “free z es” the related port[...]

13-74 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) — Continued — Per -Port LLDP Counters: NumFra mesRecvd: Shows the total number of valid, inbound LLDP advertisements received from any neighbor(s) on < port- list > . Where multiple neighbors are connected to a port through a hub, this value is the[...]

13-75 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Figure 13-22. Example of a Gl obal LLDP Statistics Display Figure 13-23. Example of a Per -Port LLDP Statistics Display LLDP Operating No tes Neighbor Maximum. The neighbors tabl e in the switch supports as many neighbors as there are ports on the sw itch. Th[...]

13-76 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) One IP Address Advertiseme nt Per -Port: LLDP advertises onl y one IP address per -port, even if multiple IP addresses are configured by lldp confi g < port-list > ipAddrEnab le on a given port. 802.1Q VLAN Informa tion. LLDP packets do not include 802[...]

13-77 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Figure 13-24. Matching Inte rnal Port Numbers to Ex ternal Slot/Port Numbers LLDP and CDP Data Management This section describes points to note regarding LLDP (Link-Layer Discovery Protocol) and CDP (Ci sco Discovery Protocol ) data received by the swit ch fr[...]

13-78 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) • The LLDP “Syste m Descr” field ma ps to CDP’ s “V ersion” and “Plat- form” fields. • The switch assigns “Cha ssisT ype” and “PortT ype” fields as “loc al” for both the LLDP and the CDP advertisements it receives. • Both LLDP[...]

13-79 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) CDP Operation and Commands By default the switche s c ove re d in th is gu id e have CDP enabled on each port. This is a read-only capability , me anin g that the switch can receive and store information about adjacent CDP devices but does not generate CDP pa[...]

13-80 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Note For details on how to use an SNMP utility to retrieve information from the switch’ s CDP Neighb ors table maintain ed in the switch’ s MIB (Mana gement Information Base), refer to the documentatio n provided with the particular SNMP utility . V iewi[...]

13-81 Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) V iewing the Switch’ s Current CDP N eighbors T able. Devices are listed by the port on which they were detected. Figure 13-26 lists CDP devices that the sw itch has detected by receiving their CDP packets. Figure 13-26. Example of CDP Neighbors T able List[...]

13-82 Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) For example, to disable CD P read-only on the switch: ProCurve(config)# no cdp run When CDP is disabled: ■ show cdp neighbors displays an empty CDP Neighbors table ■ show cdp displays Global CDP information Enable CDP [Y es]: No Enabling or Disabling CDP[...]

A-1 A File T ransfers Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Downloading Switch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 General Softwa re Download Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Using TFTP To[...]

A-2 File Transfers Contents Transferring Switch Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . A-25 TFTP: Copying a Configurat ion File to a Remote Host . . . . . . . A-25 TFTP: Copying a Config uration File f rom a Remote Host . . . . A-26 TFTP: Copying a Customized Command File to a Switch . . . . A-26 Xmodem: Copying a Config[...]

A-3 File Transfers Overview Overview The switches co vered in this gui de su pport several methods f or transferring files to and from a physic ally connected device, or vi a the network, including TFTP , Xmodem, and USB. This appendix exp lains how to d ownload new switch software, and upload or download switch conf iguration files and software im[...]

A-4 File Transfers Downloading Switch Software General Software Download Rules ■ Switch software that y ou download via the menu interface always goes to primary flash. ■ After a software download, you must reboot the switch to implement t he new software. Unti l a reboot occurs, the switch cont inues to run on the software it was usin g before[...]

A-5 File Transfers Downloading Switch Software Menu: TFTP Download from a Server to Primary Flash Note that the menu interface ac cesses only the primary flash. 1. In the console Main Menu, select Download OS to display the screen in figure A-1. (The term “OS”, or “ope rating system” refers to the switch software): Figure A-1. Example of a [...]

A-6 File Transfers Downloading Switch Software A “progress” bar indicates the progre ss of the download. When the entire software file has been received, all activ ity on the switch halts and you will see V alidating and wr iting system softw are to FLASH... 7. After the primary flash memory has been updated with the new sof t ware, you must re[...]

A-7 File Transfers Downloading Switch Software T o find more information on the cause of a do wnload fail ure, examine the messages in the switch’ s Event Log by executing the show log t ftp command from the CLI. Also: ■ For more on the Event Log, see “Usi ng the Even t Log for T roubleshooti ng Switch Problems” on page C-24. ■ For descri[...]

A-8 File Transfers Downloading Switch Software For example, to download a switch so ftware file named k0800.s wi from a TFTP server with the IP address of 10.28.227.103 to primary fl ash: 1. Execute copy as shown below: Figure A-4. Example of the Command to Download an OS (Switch Soft ware) 2. When the switch finishes downloading the software file [...]

A-9 File Transfers Downloading Switch Software 4. T o confirm that the software downloaded correctly , execute show system and check the Firmware revision line. For informati on on primary/secondary f lash memory and the b oot commands, refer to “Using Primary and Secondary Flash Image Options” on page 6 -14. Note If you use auto-tftp to downlo[...]

A-10 File Transfers Downloading Switch Software The no tftp < client | server > command does no t disabl e auto-TFTP operation. T o disable an auto-TFTP command configured on the switch, use the no auto- tftp command described on pa ge A-11 to remove the command entry from the switch’ s configuration. For information on how to configure TFT[...]

A-11 File Transfers Downloading Switch Software Using Auto-TFTP The auto-tftp command allows yo u to configure the switch to download software automatically from a TFTP server . How It W orks. At switch startup, the au to-TFTP feature automatically downloads a specifie d software i mage to the switch from a specified TFTP server , then reboots the [...]

A-12 File Transfers Downloading Switch Software Using Secure Copy and SFTP For some situ ations you may want to use a secu re method to issue command s or copy files to the switch. By open ing a secure, encrypted SSH session and enabling ip ssh file transfer , you can then use a third-party software applica tion to take advantage of Secure Copy (SC[...]

A-13 File Transfers Downloading Switch Software Protocol major versions differ: 2 vs. 1 Connection closed Protocol major versions differ: 1 vs. 2 Connection closed Received disconnect from < ip-addr > : /usr/local/ libexec/sftp-server: command not supported Connection closed SCP (secure copy) is an im plementation of the BSD rcp (Berkeley UNI[...]

A-14 File Transfers Downloading Switch Software Disable TFTP and Auto-TFTP for Enhanced Security Using the ip ssh filetransfer command to enable Secure FTP (S FTP) automat- ically disables TFTP and auto-TFTP (i f either or both are enabled). Figure A-5. Example of Switc h Configuration with SFT P Enabled If you en able SFTP , then later d isable it[...]

A-15 File Transfers Downloading Switch Software Figure A-6. Using the Menu Interface T o Disable TFTP ■ While SFTP is enabled, TFTP an d auto-TFTP cannot be enabled fr om the CLI. Attempting to enable eit her non-secure TFTP option while SFTP is enabled produces one of the following messages in the CLI: SFTP must be disabled before enabling tftp.[...]

A-16 File Transfers Downloading Switch Software Note As a matter of policy , administrators should not enable the SSHv1-only or the SSHv1-or -v2 advertisement modes. SSHv1 is supported on only some legacy switches (such as the HP ProCurve 2500 switches). T o confirm that SSH is enabled type in the command ProCurve(config)# show ip ssh Once you have[...]

A-17 File Transfers Downloading Switch Software ■ When an SFTP client conn ects, the switch prov ides a file system display - ing all of its available files and folders. No file or directory creation is permitted by th e user . Files may only be up loaded or downloaded, accord- ing to the perm issions mask. All of the necessary files the switch w[...]

A-18 File Transfers Downloading Switch Software | authorized_keys ---oper_keys authorized_keys ■ When using SFTP to copy a software image onto the switch, the command return takes only a few seconds. However , this does not mean that the transfer is complete, because the swit ch requires additi onal time (typi- cally more than one minute) to wri[...]

A-19 File Transfers Downloading Switch Software Note The Bad file number is from the system e rror value and may differ depending on the cause of the failu re. In the third example, the de vice file to read was closed as the device read was about to occur . Attempt to Start a Session During a Flash W rite. If you attempt to start an SCP (or SFTP) s[...]

A-20 File Transfers Downloading Switch Software Menu: Xmodem Download to Primary Flash Note that the menu interface ac cesses only the primary flash. 1. From the console Main Menu, select 7. Download OS 2. Press [E] (for E dit ). 3. Use the Space bar to select XMODEM in the Method field . 4. Press [Enter] , then [X] (for eX ecute ) to begin the so [...]

A-21 File Transfers Downloading Switch Software CLI: Xmodem Download from a PC or UNIX W orkstation to Primary or Secondary Flash Using Xmodem and a terminal emulator , you can download a soft ware file to either primary or secondary flash. For example, to download a switch soft ware fi le named E0822.swi fro m a PC (running a term inal emulator pr[...]

A-22 File Transfers Downloading Switch Software 4. T o confirm that the soft ware downloaded correctly: ProCurve> show system Check the Firmware revision line. It should sho w the softw are version that you downloaded in the prec eding steps. If you need info rmation on primary/secondary flas h memory and the boot commands, refer to “Using Pri[...]

A-23 File Transfers Downloading Switch Software 7. After the primary flash memory has been updated with the new sof t ware, you must reboot the switch to impl ement the newly downloaded software. Return to the Main Menu and press [6] (for Reboot Switch ). Y ou will then see this prompt: Continue reboot of system? : No Press the space bar once to ch[...]

A-24 File Transfers Downloading Switch Software Figure A-7. Switch-T o-Switch, from Primar y in Source to Either Fla sh in Destination Downloading fr om Either Flash in the Sou rce Switch to Either Flash in the Destinatio n Switch. For example, to download a software fi le from secondary flash in a switch with an IP address of 10.28.227.103 to the [...]

A-25 File Transfers Copying Software Images Copying Software Images Using the CLI commands described in this sectio n, you can copy software images from the switch to another device using tftp, xmodem, or usb. Note For details on ho w switch memory opera tes, includ ing prim ary and secondary flash, refer to Chapter 6, “Swi tch Me mory and Config[...]

A-26 File Transfers Transferring Switch Configurations T ransferring Switch Configurations T ransfer Features Using the CLI commands described in this sectio n, you can copy switch configurations to and from a switch. Note For greater security , you can perform all TFTP operations using S FTP as described in the section on Using Secure Copy and SFT[...]

A-27 File Transfers Transferring Switch Configurations TFTP: Copying a Configuration File from a Remote Host For example, to download a configurat ion file named sw8200 in the configs directory on drive “ d ” in a remote host having an IP address of 10.28.227.105: ProCurve# copy tftp startup-config 10.28.227.105 d:configssw8200 TFTP: Copying [...]

A-28 File Transfers Transferring Switch Configurations Y ou can include show tech commands in the custom file, with the exception of show tech custom . For example, y ou can include the command show tech all . If no custom file is found , a message displays stating “No SH OW -TECH file found.” Figure A-10. Example of the show te ch custom Comma[...]

A-29 File Transfers Transferring Switch Configurations 2. Execute the following command: 3. After you see the above prompt, press [Enter] . 4. Execute the termina l emulator comm ands to begin the fil e transfer . Xmodem: Copying a Configurat ion File from a Serially Connected PC or UNIX W orkstation T o u se this method , the switch must be connec[...]

A-30 File Transfers Copying Diagnostic Data to a Remote Host , USB Device, PC or UNIX Workstation (For more on these commands, refer to “Rebooting the Sw itch” on page 6-19.) Copying Diagnostic Data to a Remote Host, USB Device, PC or UNIX W orkstation Y ou can use the CLI to co py the follow ing types of switc h data to a text file in a destin[...]

A-31 File Transfers Copying Diagnostic Data to a Remote Host , USB Device, PC or UNIX Workstation Copying Command Output to a Destination Device For example, to use Xmodem to copy the output of sh ow config to a serially connected PC: Figure A-11. Example of Sendin g Command Output to a File on an Attached PC Note The command you specify must be en[...]

A-32 File Transfers Copying Diagnostic Data to a Remote Host , USB Device, PC or UNIX Workstation Figure A-12. Example of Sending Event Lo g Content to a File on an Attach ed PC Copying Crash Data Content to a Destination Device This command uses TFTP , USB, or Xmodem to copy the Crash Data con tent to a destination d evice. Y ou can copy individu [...]

A-33 File Transfers Copying Diagnostic Data to a Remote Host , USB Device, PC or UNIX Workstation Copying Crash Log Data Content to a Destination Device For example, to copy the Crash Log for sl ot C to a file in a PC co nnected to the switch: Figure A-14. Example of sen ding a Crash Log for Slot C to a File on an Attache d PC Copying Crash Logs wi[...]

B-1 B Monitoring and Analyzing Switch Operation Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Status and Counters Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 Menu Access To Stat us and Counters . . . . . . . . . . . . . . . . . . . .[...]

B-2 Monitoring and Analyzi ng Switch Operation Contents Mirroring Terminol ogy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-24 Mirrored Traffic Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-26 Local Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-[...]

B-3 Monitoring and Analyzing Switch Operation Overview Overview T he s w i t c h e s covered in this guide h a v e s e v e r al b u i l t - in t o o l s f o r m o ni t o r i n g , analyzing, and troubleshootin g switch and network operation: ■ Status: Includes options for displaying general swi tch informat ion, man- agement address data, port st[...]

B-4 Monitoring and Analyzi ng Switch Operation Status and Counters Data Status and Counters Data This section describes the status and counters screens available through the switch console interface and/or the web browser interface. Note Y ou can access a ll console screens from the web browser interface via T elnet to the console. T elnet access t[...]

B-5 Monitoring and Analyzing Switch Operation Status and Counters Data Menu Access T o St atus and Counters Beginning at the Main Menu, display th e Status and Counters menu by select- ing: 1. Status and Counters Figure B-1. The Status and Counters Menu Each of the above menu items accesses the read-only scr eens desc ribed on the followin g pages.[...]

B-6 Monitoring and Analyzi ng Switch Operation Status and Counters Data General System Information Menu Access From the console Main Menu, select: 1. Status and Counters 1. General System Information Figure B-2. Example of General Switch Informatio n This screen dynamically indicates how individual switch resources are being used. Refer to the onli[...]

B-7 Monitoring and Analyzing Switch Operation Status and Counters Data CLI Access to System Information The show system command displays general sy stem informat ion abou t the switch. Figure B-3. Example of Switch System Information Syntax: show system [information | enclosure ] Displays global system in formation and operational parameters for th[...]

B-8 Monitoring and Analyzi ng Switch Operation Status and Counters Data Ta s k M o n i t o r — C o l l e c ting Processor Data The task monitor feature al lows you to enable or disable the colle ction of processor utilizat ion data. The task-monitor cpu command is equivalent to the existing debu g mode comma nd “ taskusage -d ”. (The taskUsag[...]

B-9 Monitoring and Analyzing Switch Operation Status and Counters Data Figure B-5. Example of Management Address Information with VLANs Conf igured This screen displays a ddresses that are importan t for manage ment of the switch. If multiple VLANs are not configured, this screen displays a single IP address for the entire switch. Refe r to the onl[...]

B-10 Monitoring and Analyzi ng Switch Operation Status and Counters Data Port Status The web browser interface and the co ns ole interface show the same port status data. Menu: Displaying Port Status From the Main Menu, select: 1. Status and Counters … 4. Port Status Figure B-6. Example of Port Status on the Menu Interface CLI Access Syntax: show[...]

B-11 Monitoring and Analyzing Switch Operation Status and Counters Data V iewing Port and T runk Gr oup Statistics and Flow Control Status These feat ures enab le you to d etermine the traffic patte rns fo r each port since the last reboot or reset of the switch. Y ou can display: ■ A general report of traf fic on all LAN ports and trun k groups [...]

B-12 Monitoring and Analyzi ng Switch Operation Status and Counters Data Menu Access to Port and T runk Statistics T o access this screen from the Main Menu, select: 1. Status and Counters … 4. Port Counte rs Figure B-7. Example of Port Counters on the Menu Interface T o view details about th e traffi c on a particula r port, use the [v] key to h[...]

B-13 Monitoring and Analyzing Switch Operation Status and Counters Data CLI Access T o Port and T runk Group Statistics T o Display the Port Counter Summary Report. T o Display a Deta iled T raf fic Summary for Specific Ports. T o Reset the Port Counters for a Specific Port. W eb Browser Access T o View Po rt and T runk Group Statistics 1. Click on[...]

B-14 Monitoring and Analyzi ng Switch Operation Status and Counters Data V iewing the Switch’ s MAC Address T ables Note The 6120G/XG supports a maximum of 16,000 MAC address entries. The 6120XG supports a maximum of 32,000 MAC address entries. These features help you to view: ■ The MAC addresses that the switch has learned from network devices[...]

B-15 Monitoring and Analyzing Switch Operation Status and Counters Data Figure B-9. Example of the Address T able T o page through th e listin g, use N ext page and P rev p age . Finding the Port Connection for a Specific Devi ce on a VLAN. This feature uses a devi ce’ s MAC address that you enter to identify the port used by that device. 1. Proc[...]

B-16 Monitoring and Analyzi ng Switch Operation Status and Counters Data Port-Level MAC Address V iewing and Searching. This feat ure displays and searches for MAC addresses on the specified port instead of for all ports on the switch. 1. From the Main Menu, select: 1. Status and Counters 7. Port Address T able Figure B-11. Listing MAC Addresses fo[...]

B-17 Monitoring and Analyzing Switch Operation Status and Counters Data CLI Access for MAC Address V iews and Searches Syntax: show mac-addre ss [ vlan < vlan-id > ] [ < port-li st > ] [< mac-addr >] T o List All Learned MAC Addresse s on the Switch, with The Port Number on Which Each MAC Address W as Learned. ProCurve> show ma[...]

B-18 Monitoring and Analyzi ng Switch Operation Status and Counters Data Spanning T ree Protocol (MSTP) Information CLI Access to MSTP Data This option lists the MSTP co nfigurati on, root data, and per -port data ( cost, priority , state, and designated bridge). Figure B-12. Output from show spanning-tree Comm and Syntax: show spanning-tree This c[...]

B-19 Monitoring and Analyzing Switch Operation Status and Counters Data Internet Group Management Protocol (IGMP) Status The switch uses the CLI to display th e following IGMP st atus on a per -VLAN basis: For example, suppose that show ip igmp listed an IGMP group address of 224.0.1.22. Y ou could get additional da ta on that group by executing th[...]

B-20 Monitoring and Analyzi ng Switch Operation Status and Counters Data VLAN Information The switch uses the CLI to disp lay the following VLAN status: Note The 6120G/XG supports a maximum of 256 VLANs. The 6120XG supports a maximum of 1,024 VL ANs. For example, suppose that your switch has t he following VL ANs: PortsVLANVID A1 - A12DEF AUL T_VLA[...]

B-21 Monitoring and Analyzing Switch Operation Status and Counters Data Figure B-14. Example of VLAN Listing fo r the Entire Switch Listing the VLAN ID (VID) and Status for Specific Ports. Figure B-15. Example of VLAN Listing fo r Specific Ports Listing Individual VLAN Status. Figure B-16. Example of Port Listing for a n Individual VLAN Because por[...]

B-22 Monitoring and Analyzi ng Switch Operation Status and Counters Data W eb Browser Interface Status Information The “home” screen for the web browse r interface is the Status Overview screen, as shown below . As the title imp lies, it provides an overview of the status of the swit ch, includin g summary gr aphs indicat ing the network utili-[...]

B-23 Monitoring and Analyzing Switch Operation Traffic Mirroring T raffic Mirroring Mirror Features T raffic mirro ring (Intelligen t Mirroring) al lows you to mirror (send a copy of) network traffic received or transmit ted on a switch interface to a local destination, such as a traffic analyzer or intrusion detection syst em (IDS). T raffic mirro[...]

B-24 Monitoring and Analyzi ng Switch Operation Traffic Mirroring ■ All traffic: Monitors all traffic enteri ng or leaving the switch on one or more interfaces ( inbound and outbound ). Mirroring T erminology Figure B-18 shows an example of the term s used to describe the configurati on of a sample loca l mirroring session: ■ In the local sessi[...]

B-25 Monitoring and Analyzing Switch Operation Traffic Mirroring Caution An exit port sh ould be connected onl y to a network an alyzer , IDS, or othe r network edge device that has no connecti on to other net work resources. Connecting a mirroring exit port to a network can result in serious network performance problems, and i s strongly discourag[...]

B-26 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Mirrored T raffic Destinations Local Destinations A local mirrored traffic destination is a port on the same switch as the source of the traffic being mirrore d. Caution Configuring a mirroring sour ce switch with the destination an d traffic selec- tion criteria for a given mirrorin[...]

B-27 Monitoring and Analyzing Switch Operation Traffic Mirroring Mirroring Configuration T able B-1 shows the differen t types of mirroring that you can conf igure using the CLI, Menu, and SNMP interfaces. T able B-1. Mirroring Configuration Opti ons Monitoring Interface and Configuration Level T raffic Selection Criteria T raffic Direction CLI Con[...]

B-28 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Configuration Notes Using the CLI, you can configure a ll mirroring opti ons on a switch. Using the Menu or W eb interface, you ca n configure sessi on 1 local mirroring for traffic in both direct ions on specified interfaces. (If session 1 has been already configur ed in the CLI for[...]

B-29 Monitoring and Analyzing Switch Operation Traffic Mirroring Using the Menu or W eb Inte rface T o Configure Local Mirroring Menu and W eb Interface Limits The Menu and W eb interfaces can be used to quickly configur e or reconfigure local mirroring on session 1, and allow the fo llowing mirroring source opti on: ■ any combination of source p[...]

B-30 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Configuration Steps Notes If mirroring has al ready been enabled on th e switch, the Men u screens will appear differently than shown in this section. 1. From the Main Menu, select: 2. Switch Configuration ... 3. Network Monitoring Port Figure B-19. The Default Network Mirrorin g Con[...]

B-31 Monitoring and Analyzing Switch Operation Traffic Mirroring Figure B-20. How T o Select a Local Exit Port 5. Use the Space bar to se lect the port to use for sending mirrored traf fic to a locally connected traffic analyzer or IDS. (The selected interface must be a single port. It cannot be a trunk .) In this exam ple, port D5 i s selected as [...]

B-32 Monitoring and Analyzi ng Switch Operation Traffic Mirroring 8. Press the Sp ace bar t o select Monitor for the port( s) and/or trunk(s) that you want mirrore d. Use the down a rrow key to move from one interface to the next in th e Action column. (If any trunks are co nfigured, they w ill appear at the end of the port listing.) 9. When you fi[...]

B-33 Monitoring and Analyzing Switch Operation Traffic Mirroring CLI: Configuring Local Mirroring Using the CLI, you can configure a mirr oring session for a destination device connected to an exit po rt on the same switch as the source interface (local mirroring). For an overview of the proced ures for configuring a local mirroring ses sion, refer[...]

B-34 Monitoring and Analyzi ng Switch Operation Traffic Mirroring 1. Determine the session and local destination port: • Session number (1-4) and (optional ) alphanumeric name • Exit port (any port on the switch except a monitored interface used to mirror traff ic) 2. Enter the mirror < session -# > [ name < session - name >] port &[...]

B-35 Monitoring and Analyzing Switch Operation Traffic Mirroring 1. Determine the Mirroring Session and Destination For a Local Mirroring Session. Determine the port num ber for the exit port (such as A5, B10, etc.), then go to “3. Configure the Monitored T raffic in a Mirror Session” on page B-35. 2. Configure a Mirroring Session on the Source[...]

B-36 Monitoring and Analyzi ng Switch Operation Traffic Mirroring T raffic Selection Options T o configure traffic mirroring, you must specify the source interface , traffic direction, and criteria t o b e u s e d t o s e l e c t t h e t r affic to be mirrored using the following op tions: ■ Interface type • Port and/or trunk • Switch (global[...]

B-37 Monitoring and Analyzing Switch Operation Traffic Mirroring This command assigns a mirrori ng source to a previously configured mirroring session on a source switch. It specifi es the port and/or trunk source(s) to u se, the direction of traffic to mirror , and the session identifier . The no form of the command removes a mirroring source assi[...]

B-38 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Displaying a Mirroring Configuration Displaying the Mirroring Configuration Summary Use the show monitor command to display inform ation on the currently con- figured status, traffi c-selection criteria , and number of monitored interfaces in each mirroring session on a switch. Figur[...]

B-39 Monitoring and Analyzing Switch Operation Traffic Mirroring Policy: Indicates whether the source is using a classifier -based mirroring policy to select inbo und IPv4 or IPv6 traffic for mirroring. Syntax: show monitor[...]

B-40 Monitoring and Analyzi ng Switch Operation Traffic Mirroring V iewing Mirroring in the Current Configuration File Using the show run command, you can view the current mirroring config ura- tion on t he switch. Source mirroring session entries begin wi th the mirror keyword and the mirroring sources are listed per -inte rface. F or example: Fig[...]

B-41 Monitoring and Analyzing Switch Operation Traffic Mirroring Mirroring Configuration Examples Local Mirroring Using T r affic-Direction Criteria Example of Local Mirroring Configuration. An administrator wants to mirror the inbound traffic from workst ation “X” on port A5 and workstation “Y” on port B17 to a traffic analyzer c onnected [...]

B-42 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Maximum Supported Frame Size The IPv4 encapsul ation of mirrored tra f fic adds a 54-byte header to each mirrored frame. If a resulting frame exceeds the MTU (M aximum T ransmis- sion Unit) allow ed in the netw ork, the frame is dr opped. Note Mirroring does not truncate frames, an d[...]

B-43 Monitoring and Analyzing Switch Operation Traffic Mirroring Enabling Jumbo Frames T o Increase Mirroring Path MTU On 1 Gbps and 10 Gbps ports in the mi rroring path, you can redu ce the number of dropped frames by en abling jumbo fr ames on all intermed iate switches and routers. (The maxi mum transmission unit—MTU—on the sw itches covered[...]

B-44 Monitoring and Analyzi ng Switch Operation Traffic Mirroring Effect of Downstream VLAN T agging on Untagged, Mirrored T raffic In a mirroring applicat ion, if mirrored traffic leaves the switch without 802.1Q VLAN tagging, bu t is forwarded through a downstream device that adds 802.1Q VLAN tags, then the MTU for untag ged, mirrored frames leav[...]

B-45 Monitoring and Analyzing Switch Operation Traffic Mirroring Operating Notes ■ Mirroring Dropped T raffic: Where an interface is configured to mirror - ing traffic to a destination, it does so regardless of whether the traffic is dropped while on the interface. ■ Mirroring and Spanni ng T ree: Mirroring is done regardless of the spanning-tr[...]

B-46 Monitoring and Analyzi ng Switch Operation Traffic Mirroring ports B5, B6, and B7 is b eing mirrored through port B7 t o a network analyzer , the mirrored frames from tr affic on ports B5 an d B6 will not be mirrored a second ti me as they pass through port B7. ■ Switch Operation as Both Destinatio n and Source: A switch config- ured as remo[...]

B-47 Monitoring and Analyzing Switch Operation Traffic Mirroring T roubleshooting Mirroring Mirrored traffic does not reach config ured remote destination switch or remote exit port. • For a given mirroring sessi on, the mirror command pa rameters con- figured on the source switch for so urce IP address, source UDP port, and destinat ion IP addre[...]

C-1 C T roubleshooting Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 Troublesho oting A pproache s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 Browser or Telnet Access Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7 Unusual[...]

C-2 Troubleshooting Contents Using Log Throttling to Reduce Duplicate Event Log and SNMP Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-33 Log Throttle Periods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-34 Example of Log Throttling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-34 [...]

C-3 Troubleshooting Contents Customizing show tech Comma nd Output . . . . . . . . . . . . . . . . . C-69 CLI: Viewing M ore Info rmation on Switch Operation . . . . . . . . . . . C-72 Pattern Matching When Using t he Show Command . . . . . . . . . C-73 CLI: Useful Commands for Troublesh ootin g Sessions . . . . . . . . . . . C-76 Restoring the Fac[...]

C-4 Troubleshooting Overview Overview This appendix addresses performance- relat ed network problems th at can be caused by topology , switch configur ation, and t he effects of other devi ces or their config urations on sw itch operation. (For swit ch-specific i nformation on hardware problems indicated by LED behavior , cabling requi rements, and[...]

C-5 Troubleshooting Troubleshooting Approaches T roubleshooting Approaches Use these approaches to diagnose switch problems: ■ Check the HP support web site fo r soft ware updates that may have solved your problem: www.hp.com/#support ■ Check the switch LEDs for indicati ons of proper switch op eration: • Each switch port has a Link LE D th a[...]

C-6 Troubleshooting Troubleshooting Approaches ■ For the downlink and ISL po rts, troubleshoot ing can be done from the OA W eb interface. These ports are controlled from both the OA and the switch configuration. A port st ate is a combination of OA En able/Disable stat e and the switch Enable/Disable stat e. The port is not Enabled unt il both t[...]

C-7 Troubleshooting Browser or Telnet Access Problems Browser or T elnet Access Problems Cannot access the we b browser interface: ■ Access may be disabled by the Web Agent Enabled parameter in the switch console. Check the se tting on this param e ter by selecting: 2. Switch Configuration … 1. System Information ■ The switch may not have the[...]

C-8 Troubleshooting Browser or Telnet Access Problems Cannot T elnet into the switch con sole from a station on the network: ■ T elnet a ccess may be disabled by the I nbound T elnet Enabled pa rameter in the System Informati on scr een of the menu interface: 2. Switch Configuration 1. System Information ■ The switch may not have the correct IP[...]

C-9 Troubleshooting Unusual Network Activity Unusual Network Activity Network activity that fails to meet ac cepted norms may indicate a ha rdware problem with one or more of the netw ork components, possibl y including the switch. Such problems can also be caused by a network lo op or simply too much traffic for t he network as it is currently des[...]

C-10 Troubleshooting Unusual Network Activity This can also happen, for example, if the server is first conf igured to issue IP addresses with an un limited duration, th en is subsequently co nfigured to issue IP addresses that will expire aft er a limited duration. One solution is to configure “reservations” in the DHCP server for speci fic IP[...]

C-11 Troubleshooting Unusual Network Activity IP Multicast T raf fic Floods Out All Ports; IGMP Does Not Appear T o Filter T raffic. The IGMP feature does not operat e if the switch or VLAN does not have an IP address configured manu ally or obtained through DHCP/B ootp. T o verify wh ether an IP address is config ured for the switch or VLAN, do ei[...]

C-12 Troubleshooting Unusual Network Activity The switch does not receive a res ponse to RADIUS authentication requests. In this case, the switch wi ll attempt authen tication using the secondary method configured for the type of acce ss you are using (console, T eln et, or SSH). There can be several reasons for not recei ving a response to an auth[...]

C-13 Troubleshooting Unusual Network Activity The supplicant statistics listing sh ows multiple ports with the same authenticator MAC address. The li nk to the authen ticator may have been moved from one port to anot her without the su pplicant statist ics having been cleared from the first po rt. Refer to “Note on Supp licant Statistics” in th[...]

C-14 Troubleshooting Unusual Network Activity Figure C-2. Displaying Encryption Keys Also, ensure that the swit ch port used to access the RADIUS server is not blocked by an 802.1X configu ration on that p ort. For example, show port - access authenticator < p ort-list > gives you the status for the specified ports. Also, ensure that other fa[...]

C-15 Troubleshooting Unusual Network Activity Radius-Related Problems The switch does not receive a res ponse to RADIUS authentication requests. In this case, the switch wi ll attempt authen tication using the secondary method configured for the type of acce ss you are using (console, T eln et, or SSH). There can be several reasons for not recei vi[...]

C-16 Troubleshooting Unusual Network Activity Spanning-T ree Protocol (MSTP) and Fast-Uplink Problems Caution If you enable MSTP , it is recommende d that you leave the remainder of the MSTP param eter settings at their defaul t values until you have had an oppor - tunity to evaluate MSTP performance in your network. B ecause incorrect MSTP setting[...]

C-17 Troubleshooting Unusual Network Activity SSH-Related Problems Switch access refused to a client. Even though you have pla ced the client’ s public key in a text file and copied the file (using the copy tftp pub -key- file command) into the switch, the switch refuses to allow the client to have access. If the source SSH client is an SSHv2 a p[...]

C-18 Troubleshooting Unusual Network Activity Switch does not detect a client’ s public key that does appear in the switch’ s public key file ( sh ow ip client-public-key ). The client ’ s public key entry in the public key fi le may be pr eceded by an other entry that does not terminate wi th a new line (CR). In th is case, the switch in ter[...]

C-19 Troubleshooting Unusual Network Activity T ACACS-Related Problems Event Log. When troubleshooting T ACACS+ op eration, check the switch’ s Event Log for i ndications of p roblem areas. All Users Are Locked Out of Access to the Switch. If the switch is f unc- tioning properly , but no username/password pairs resul t in console or T elnet acce[...]

C-20 Troubleshooting Unusual Network Activity ■ The encryption key configured in the server does not match the encryption key configured in the switch (by using the tacacs-server key command). V erify the key in the server and compare it to the key configured in the switch. (Use show tacacs-server to list the glob al key . Use show config or show[...]

C-21 Troubleshooting Unusual Network Activity T imeP , SNTP , or Gateway Problems The Switch Cannot Find the T ime Se rver or the Con figured Gateway . T imeP , SNTP , and Gatew ay access are through the primary VLAN, which in the default configuration is the DE F AUL T_VLAN. If the primary VLAN has been moved to another VLAN, it may be disabled or[...]

C-22 Troubleshooting Unusual Network Activity Figure C-4. Example of Correct VLAN Port Assignments on a Link 1. If VLAN_1 (VID=1) is conf igured as “Untagged” on port 3 on switch “X”, then it must also be co nfigured as “Untagged” on port 7 on switch “Y”. Make sure that the VLAN ID (VID) is the sam e on both switches. 2. Similarl y [...]

C-23 Troubleshooting Unusual Network Activity Figure C-5. Example of Duplicate MAC Address Server 8212zl Switch (Multiple Forwarding Database) Switch with Single Forwarding Database MAC Address “A”; VLAN 1 MAC Address “A”; VLAN 2 Problem: This switch detec ts continual move s of MAC address “A” between ports. VLAN 1 VLAN 2[...]

C-24 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems Using the Event Log for T roubleshooting Switch Problems The Event Log records oper ating event s in single- or double-line entries and serves as a tool to isolat e and troubl eshoot problems. Starting in software release K.13. xx , the maximum number of entries supported[...]

C-25 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems D (debug) is reserved for ProCurve intern al diagnost ic informatio n. Date is the date in the format mm/dd/yy when an entry is recorded i n the log. Ti m e is the time in the format hh:mm:ss when an entry is recorded in the log. Event Number is the number assigne d to an[...]

C-26 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems cos Class of Service (CoS): Prov ides priority handling of packets traversing the switch, based on the IEEE 802.1p priority carrie d by each packet. CoS messages also include Qual ity of Service (QoS) events. The QoS feature classifies and pr ioritizes traffic throughout [...]

C-27 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems igmp Internet Group Management Protocol: Reduces unnecessary bandwidth usage for multicast traffic transmitted from multimedia applications on a per -port basis. Multicast and Routing Guide ip IP addressing: Configures the switch with an IP address and subnet mask to comm[...]

C-28 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems maclock MAC lockdown and MAC lockout • MAC lockdown prevents station movement and MAC address “hijacking” by requi ring a MAC address to be used only an assigned port on the switch. MAC Lockdown also restricts the client device to a specific VLAN. • MAC lockout bl[...]

C-29 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems stp Multiple-instance spanning tree protocol/M STP (802.1s): Ensures that only one active path exists between any two nodes in a group of VLANs in the network. MSTP operation is designed to avoid loops and br oadcast storms of duplicate messages that can bring down the ne[...]

C-30 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems vlan Static 802.1Q VLAN operat ions, including port-and protocol- based configurations that group users by logical function instead of physical location • A port -based VLAN creates a layer-2 broadcast domain comprised of member ports t hat bridge IPv4 traffic among the[...]

C-31 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems Menu: Displaying and Navi gating in the Event Log T o displa y the Event Log fr om the Main Menu, select Event Log . Figure C-6 shows a sample ev ent log display . Figure C-6. Example of an Event Log Display The log status line below the recorded entries states the total [...]

C-32 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems CLI: Displaying the Event Log T o displa y messages record ed in the event log fr om the CLI, enter the show logging command. Keyword searches are supported. Examples. T o di splay all Event Log message s that have “system” in the message text or module name, enter th[...]

C-33 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems T o redispl ay all hidden entries, includi ng Event Log entries recorded prior to the last r eboot, ente r the show logging -a command. CLI: T urning Event Numbering On Using Log Throttling to Reduce Duplicate Event Log and SNMP Messages A recurring event can gener ate a [...]

C-34 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems Log Throttle Periods The length of the l og throttle pe riod di ffers according to an event’ s severity level: Example of Log Throttling For example, suppose that yo u configure VLAN 100 on the switch to suppor t PIM operation, but do no t configure an IP address. If PI[...]

C-35 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems If PIM oper ation caused th e same event to occur si x more times duri ng the initial log throt tle period, there would be no further entries i n the Event Log. However , if the event occurr ed again after the log throttl e period expired, the switch would rep eat the mes[...]

C-36 Troubleshooting Using the Event Log for Tr oubleshooting Switch Problems Example of Event Counter Operation Suppose the switch detects the following after a re boot: ■ Three duplicate instances of the PIM “Send error” during the firs t log throttle period for this event ■ Five more instan ces of th e same Send error during the second l[...]

C-37 Troubleshooting Debug/Syslog Operation Debug/Syslog Operation While the Event Log records switch-l evel progress, status, and warning messages on the swi tch, the Debu g/System Logging ( Syslog ) feature provides a way to record Event Log and debu g messages on a remote device. For example, you can send messages about routing misconfigurations[...]

C-38 Troubleshooting Debug/Syslog Operation A Debug/Syslog destination device can be a Syslog server and/or a console session. Y ou can configure debug and logging messages to b e sent to: ■ Up to six Syslog servers ■ A CLI session through a direct RS-232 co nsole connection, or a T elnet or SSH session Debug/Syslog Conf iguration Commands Even[...]

C-39 Troubleshooting Debug/Syslog Operation Figure C-8. Summary of Debug /Syslog Configuration Com mands Using the Debug/Syslog f eature, you can perform th e following operations: ■ Configure the switch to send Event Log messages to one or more Syslog servers. In addition, you can configure the messages to be se nt to the User log facility (defa[...]

C-40 Troubleshooting Debug/Syslog Operation b. Re-enter the log ging command in St ep “a” to configure addition al Syslog servers. Y ou can configure up to a total of six servers. (When multiple server IP addresses are configured, the switch sends the debug messa ge types that y ou configur e i n Step 3 to all IP addresses.) 2. T o use a CLI se[...]

C-41 Troubleshooting Debug/Syslog Operation Caution If you configure a severit y-level, sy stem-module, logging destination, or logging facility value and save the settin gs to the startup configurat ion (for example, by entering the write memory command), the debug settings are saved after a system reboot (power cycle or reboot) and re-activated o[...]

C-42 Troubleshooting Debug/Syslog Operation messages sent to the Syslog server , speci fy a set of messages by entering the logging severity and logging system-module commands. Figure C-2. Syslog Configuration to Receive E vent Log Messages From Specified System Module and Severity Levels As shown at the top of Figure C-2, if you enter the show deb[...]

C-43 Troubleshooting Debug/Syslog Operation Example. The next example shows ho w to configure: ■ Debug logging of IP-OSPF packet messages on a Syslog server at 18.38.64.164 (with user as the default logging facility). ■ Display of these messages in the CLI session of your terminal device’ s management access to the switch. ■ Blocking Event [...]

C-44 Troubleshooting Debug/Syslog Operation Figure C-6. Debug/Syslog Configura tion for Multiple Debug T ypes and Multiple Destinations ProCurve# config ProCurve(config)# logging 10. 38.64.164 ProCurve(config)# show debug Debug Logging Destination: Logging -- 10.38.64.164 Facility=user Severity=debug System module=all-pass Enabled debug types: even[...]

C-45 Troubleshooting Debug/Syslog Operation Debug Command At the manager level, use the debug command to perform two main functions: ■ Specifies the types of event messages to be sent to an ex ternal destination. ■ Specifies the de stinations to whic h selecte d message types are sent. By default, no debug destination is enabled a nd only Event[...]

C-46 Troubleshooting Debug/Syslog Operation ip [ ospf < adj | event | flood | lsa-generation | packet [ packet -type ] | retransmission | spf > ] For the configured debug destination(s): ospf < adj | event | flood | lsa-generation | packet [ packe t-type ] | retransmission | spf > — Enables the specified IP-OSPF message type. adj — [...]

C-47 Troubleshooting Debug/Syslog Operation Debug Destinations Use the debug destination command to enable (and disable) Syslog messaging on a Syslog server or to a CLI session for specified types of debug and Event Log messages. Syntax: [no] debug d estination < logging | session | b uffer | debug-console> logging Enables Syslog loggin g to [...]

C-48 Troubleshooting Debug/Syslog Operation Logging Command At the global configuration level, the lo gging command allows you to enable debug logging on specified Syslog server s and select a subset of Event Log messages to send for debuggi ng purposes according to: ■ Severity level ■ System modul e By specifying both a severity level and syst[...]

C-49 Troubleshooting Debug/Syslog Operation Configuring a Syslog Server Syslog is a client-server logging tool th at allows a client switch to send event notification messages to a networked de vice operati ng with Syslog server software. Messages sent to a Syslog server can be stored to a file for later debugging analysis. T o use the Syslog featu[...]

C-50 Troubleshooting Debug/Syslog Operation Syntax: [no] logging < syslog-ip-addr > [oobm] Enables or disables Syslog messaging to the specified IP address. You can configure up to six addresses. If you configure an address when none are already configured, this command enables destinatio n logging (Syslog) and the Event debug type. Therefore[...]

C-51 Troubleshooting Debug/Syslog Operation Adding a Description for a Syslog Server Y ou can associate a user -friendly descri ption with each of the IP addresses (IPv4 only) conf igured for syslog u sing the CLI or SNMP . Note The HP enterprise MIB hpicfSyslog.mi b allows the conf iguration and mon i- toring of syslog for SNMP (RFC 3164 supporte [...]

C-52 Troubleshooting Debug/Syslog Operation The CLI comm and is: Figure C-9. Example of the Logging Command wit h a Control Description Caution Entering the no logging command re moves ALL the syslog server addresses without a verification prompt. Adding a Priority Description Y ou can add a user -friendly description fo r the set of syslog filter [...]

C-53 Troubleshooting Debug/Syslog Operation Figure C-10. Exampl e of the Logging Command wit h a Priority Description Note A notification is sent to the SNMP agent if there are any changes to the syslog parameters eith er through the CLI or with SN MP . Configuring the Severity Le vel for Event Log Messages Sent to a Syslog Server Event Log message[...]

C-54 Troubleshooting Debug/Syslog Operation Configuring the System Module Us ed to Select the Event Log Messages Sent to a Syslog Server Event Log messages contain the name of the system module that reported the event. Using the logging system-module command, you can select a set of Event Log messages according to the originating system module and [...]

C-55 Troubleshooting Debug/Syslog Operation ■ Debug commands do not af fect normal message output to th e Event Log. Using the debug event command, you can specify that Event Log messages are sent to the debug de stinations you configure (CLI session and/ or Syslog servers) in addition to the Event Log. ■ Ensure that your Syslog se rver s accep[...]

C-56 Troubleshooting Diagnostic Tools Diagnostic T ools Diagnostic Features Feature Default Menu CLI Web Port Auto negotiation n/a — — — Ping test n/a — page C-59 page C-58 Link test n/a — page C-59 page C-58 T raceroute operation n/a — page C-61 n/a View switch configuration files n/a — page C-65 page C-65 View switch (sho w tech) op[...]

C-57 Troubleshooting Diagnostic Tools Port Auto-Negotiation When a link LED does not light (indicat ing loss of link between two devices), the most common r e ason is a failure of port auto -negotiation between the connecting ports. If a lin k LED fails to light wh en you conn ect the swi tch to a port on another devi ce, do the following: 1. Ensur[...]

C-58 Troubleshooting Diagnostic Tools W eb: Executing Ping or Link T ests Figure C-11. Link and Ping T est Screen on the Web Browser Interface Successes indicates the number o f Ping or Link packets that successful ly completed the m ost recent test. Failures indicates the number of Ping or Link packets that were unsuccessful in the last test. Fail[...]

C-59 Troubleshooting Diagnostic Tools Number of Packets to Send is th e number of times you wan t the switch to attempt to test a connection. T imeout in Seconds is th e number of seconds to allow per attempt to test a connection before determining that the current atte mpt has failed. T o halt a Link or Ping test before it con cludes, click on t h[...]

C-60 Troubleshooting Diagnostic Tools Figure C-12. Examples of Ping T ests T o halt a ping test before it concludes, press [Ctrl] [C] . Note T o use the ping (or traceroute ) command wit h host names or fully qualified domain names, refer to “ DNS Resolver” on page C-79. Link T ests Y ou can issue single or m ultiple link te sts with varying r [...]

C-61 Troubleshooting Diagnostic Tools Syntax: link < mac-address > [repetitions < 1 - 999 >] [timeout < 1 - 256 >] [vlan < vlan-id >] Figure C-13. Exa mple of Link T ests T raceroute Command The traceroute command enables you to trace th e route from the switch to a host address. This command outputs info rmation for each (r[...]

C-62 Troubleshooting Diagnostic Tools Lists the IP address or hostname of each hop in the route, plus the time in microseconds for the traceroute packet reply to the switch for each hop. T o halt an ongoing traceroute search, press the [ Ctrl ][ C ] keys . Note : For information about traceroute6 , see the “IPv6 Configuration Guide” for your sw[...]

C-63 Troubleshooting Diagnostic Tools A Low Maxttl Causes T raceroute T o Halt Before Reaching the Destination Ad dress. For example, executi ng traceroute with its default values for a destination IP address that is four ho ps away produces a result similar to this: Figure C-14. Exa mple of a Completed T racero ute Enquiry Continuing from the prev[...]

C-64 Troubleshooting Diagnostic Tools If A Network Condition Preven ts T raceroute from Reaching the Destination. Common reasons for T raceroute fa iling to reach a de stination include: ■ T im eouts (indicate d by one asterisk per probe, per hop; refer to Figure C-15, above.) ■ Unreachable hosts ■ Unreachable networks ■ Interference from f[...]

C-65 Troubleshooting Viewing Switch Configuration and Operation V iewing Switch Configuration and Operation In some troubleshoot ing s cenarios, you may need to view the switch config- uration to diagnose a problem. Th e co mplete s witch config uration is con- tained in a file that yo u can browse fr om either the web brow ser interface or the CLI[...]

C-66 Troubleshooting Viewing Switch Configur ation a nd Operation ■ Image stamp (software version data) ■ Running configuration ■ Event Log listing ■ Boot History ■ Port settings ■ Status and counters — po rt status ■ IP routes ■ Status and counters — VLAN information ■ GVRP support ■ Load balancing (tru nk and LACP) Figure [...]

C-67 Troubleshooting Viewing Switch Configuration and Operation Saving show tech Command Output to a T ext File When you enter the show tech command, a summary of switch operational data is sent to your termin al emulator . Y ou can use your terminal emul ator’ s text captur e features to save the show tech data to a text file for viewing, printi[...]

C-68 Troubleshooting Viewing Switch Configur ation a nd Operation ProCurve# show tech The show tech command output is copied into the text file and displayed on the ter minal emul ator screen . When the c ommand out put stops and displays -- M ORE -- , press the Space bar to di splay and copy more informatio n. The CLI prompt appears when the comma[...]

C-69 Troubleshooting Viewing Switch Configuration and Operation Syntax: copy < source > show- tech crash- log [ slot-id | master]: Includes the crash logs from all management and interface modules in show tech command output. event-log Copies the contents of the Event Log to show t ech command output. running-config Includes the contents of t[...]

C-70 Troubleshooting Viewing Switch Configur ation a nd Operation Copies the contents of a configuration file from a serially connected PC or UNIX workstation to show tech command output, where: startup-config : Specifies the name of the startup configuration file on the connected device. config < filename >: Specifies the pa thname of a conf[...]

C-71 Troubleshooting Viewing Switch Configuration and Operation CLI: Vi ewing More Informat ion on Switch Operation Use the following commands to displa y additional information on switch operation for trou bleshooting purposes. Syntax: show boot-history Displays the crash informatio n saved for each management module on the switch (see “Displayi[...]

C-72 Troubleshooting Viewing Switch Configur ation a nd Operation Pattern Matching When Using the Show Command The pattern matching op tion with the show command provides the ability to do searches for specific text. Selected portions of the outp ut are displayed depending on the parame ters chosen. Note Pattern matching is case-sensiti ve. Below a[...]

C-73 Troubleshooting Viewing Switch Configuration and Operation Figure C-21. Exa mple of Pattern Matching with E xclude Option ProCurve(config)# show run | exclude ipv6 Running configuration: ; J8697A Configuration Edito r; Created on release #K.14.06 hostname "ProCurve Switch 54 06zl" module 1 type J8702A module 2 type J8705A snmp-server[...]

C-74 Troubleshooting Viewing Switch Configur ation a nd Operation Figure C-22. Exampl e of Pattern Matching with Begin Option Figure C-23 is an example of the show arp command output, and then th e output displayed when the include option has the IP address of 15.255.128.1 as the regular expression. Figure C-23. Exampl e of the Show ARP Command and[...]

C-75 Troubleshooting Viewing Switch Configuration and Operation CLI: Useful Commands for T roubleshooting Sessions Use the following commands in a troubleshooti ng session to more accurately display the information yo u need to diagnose a problem. For more informati on on other CLI practices, refer to chapte r 4, “Using the Command Line Interface[...]

C-76 Troubleshooting Restoring the Factory-Default Configuration Restoring the Factory-Default Configuration As part of your troubleshooti ng process, it may become necessary to return the switch configuration to the factor y default settings. This process momen- tarily interrupts t he switch operatio n, clears any passwords, clears the console Eve[...]

C-77 Troubleshooting Restoring a Flash Image 3. When the Self T est LED begins to flash, relea se the Clear but ton. The switch will then complete its self te st and begin operating with the configuration restored to th e factory default settings. Restoring a Flash Image The switch can lose its op erating system if either the primary or secondary f[...]

C-78 Troubleshooting Restoring a Flash Image Make sure that the switch automaticall y boots into ROM first. 4. Start the Conso le Downlo ad utilit y by typing do at the => prompt and pressing [Enter] : => do 5. Y ou will then see this prompt: 6. At the above prompt: a. T ype y (for Y es) b. Select Tr a n s f e r | File in HyperT erminal. c. E[...]

C-79 Troubleshooting DNS Resolver DNS Resolver The Domain Name System (D NS) resolver is designed for use in local network domains where it enables us e of a host name or fully qualified domain name with DNS-com patible switch CLI comman ds. (At softwa re release K.13.01, the DNS-compatible commands include ping and traceroute .) Beginning wi th so[...]

C-80 Troubleshooting DNS Resolver Basic Operation ■ When the switch is configured wit h only the IP address of a DNS server available to the switch, then a DNS-compatible command, executed with a fully qualified doma in name, can reac h a device found in any domain accessible through the configured DNS se rver . ■ When the switch is config ured[...]

C-81 Troubleshooting DNS Resolver Note that if the target host is in a domain other than the domain configured on the switch, then: ■ The host’ s domain must be reachabl e from the switch . This requires that the DNS server for the switch must be able to communicate with the DNS serv er(s) in the path to the domain in w hich the targ et host op[...]

C-82 Troubleshooting DNS Resolver c. The domain name for an accessible domain in which there are hosts you want to reach with a DNS-c ompatible command. (This is the domain s uffix in the f ully qualif ied domain name for a given host operating in the select ed domain. Refer to “T erminology” on page C- 79.) Note that if a domain suffix is n ot[...]

C-83 Troubleshooting DNS Resolver Example Using DNS Names wi th Ping and T raceroute In the network illu strated in Figure C-27, the switch at 10.28.192 .1 is config- ured to use DNS names for DN S- compatible commands in the pubs.outdoors . com domain. The DNS server has be en configured to assign the host name docservr to the IP address used by t[...]

C-84 Troubleshooting DNS Resolver Configuring switch “A” with the domai n name and the IP address of a DNS server for the domain enables the switch to use host names assigned to IP addresses in the do main to perform ping and traceroute actions on the devic es in the domain. T o summarize: W ith the above alrea dy configured, th e following com[...]

C-85 Troubleshooting DNS Resolver As mentioned under “Basic Operation” on page C-80, if the DNS entry config- ured in the switch does not include the domain suffi x for the desired ta rget, then you must use the target host’ s fully qualified dom ain name with DN S- compatible commands. For example, using the docume nt server in Fi gure C- 27[...]

C-86 Troubleshooting DNS Resolver Operating Notes ■ Configuring anot her IP address for a priority that has already been assigned to an IP address is not a llowed. T o re place one IP address at a given priority level w ith another ad dress hav ing the same priority , you must first use the no form of the command to remove the unwanted address. A[...]

C-87 Troubleshooting DNS Resolver Event Log Messages Message Meaning DNS server address not configure d The swit ch does not have an IP a ddress configured for the DNS server . DNS server not responding The DNS serve r failed to respond or is unreach able. An incorrect server IP address can produce t his result. Unknown host < ho st-name > T [...]

D-1 D MAC Address Management Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2 Determining MAC Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3 Menu: Viewing th e Switch’s MAC Addresses . . . . . . . . . . . . . . . . . . . . D-4 CLI: View[...]

D-2 MAC Address Management Overview Overview The switch assigns MAC addresses in these areas: ■ For management functions, one Base MAC address is assigned to the de f a u l t V L AN ( V I D = 1 ) . (A l l V L A N s o n th e s w i t c h es covered in this guide use the same MAC address. ) ■ For internal switch operations: One M AC address per po[...]

D-3 MAC Address Management Determining MAC Addresses Determining MAC Addresses MAC Address Viewing Methods ■ Use the menu interface to view the switch’ s base MAC address and the MAC address assigned to any VLAN you have configured on the switch. (The same MAC address is assigned to VLAN1 and all other VLANs configured on the switch.) Note The [...]

D-4 MAC Address Management Determining MAC Addresses Menu: V iewing the Switch’ s MAC Addresses The Management Address Information screen lists the MAC addresses for: ■ Base switch (d efault VLAN; V I D = 1) ■ Any additional V LANs conf igured on the switch. Also, the Base MAC address appears on a label on the back of the switch. Note The Bas[...]

D-5 MAC Address Management Determining MAC Addresses CLI: Vi ewing the Port and VLAN MAC Addresses The MAC address assigned to each switch port is used inte rnally by such features as Flow Control and the spanning-tree protocol. Using the walkmib command to determi ne the MAC address assignment s for individu al ports can sometimes be useful when d[...]

D-6 MAC Address Management Determining MAC Addresses Figure D-2. Example of Port MAC Address Assignments on a Switch ProCurve# walkmib ifphysa ddress ifPhysAddress.1 = 00 12 7 9 88 b1 ff ifPhysAddress.2 = 00 12 7 9 88 b1 fe ifPhysAddress.3 = 00 12 7 9 88 b1 fd ifPhysAddress.4 = 00 12 7 9 88 b1 fc ifPhysAddress.49 = 00 12 79 88 b1 cf ifPhysAddress.5[...]

D-7 MAC Address Management Viewing the MAC Addresses of Connected Devices V iewing the MAC Addresses of Connected Devices T o list the MAC addresses of devi ces the switch has detected, use the show mac-address command. Syntax: show mac-address [ | mac-addr | Lists the MAC addresses of the device s the switch has detecte d, along with the number of[...]

E-1 E Monitoring Resources Contents Viewing Information on Resource Usage . . . . . . . . . . . . . . . . . . . . . . . E-2 Policy Enforcement Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 When Insufficie nt Resource s Are Avai lable . . . . . . . . . . . . . . . . . . . . E-3[...]

E-2 Monitoring Resources Viewing Information on Resource Usage V iewing Information on Resource Usage The switch allows you to view info rmation about the curren t usage and availability of resources in t he Policy Enforce ment engine, incl uding the following software features: ■ QoS through RADIUS authentication designated as “IDM”, w ith o[...]

E-3 Monitoring Resources When Insufficient Resources Are Available When Insufficient Resources Are A vailable The switch has ample r esources for conf iguring features and supporting: ■ RADIUS-authen ticated client s (with or wi thout the optional ID M applica- tion) ■ Viru s throttling and b locking on indi vidual clients. Note Virus throttlin[...]

F-1 F Daylight Savings T ime on ProCurve Switches ProCurve switches provide a way to automatically adjust the system clock for Daylight Savings Time (DST) changes. T o use this feature you defin e the month and date to begin and to en d the change from standard time. In addi tion to the value “none” (no time changes), the re are five pre-define[...]

F-2 Daylight Savings Time on ProCurve Switches Middle Europe and Portugal : • Begin DST at 2am the first Su nday on or afte r March 25th. • End DST at 2am the first Sund ay on or after September 24th. Southern Hemisphere: • Begin DST at 2am the first Sund ay on or afte r October 25th. • End DST at 2am the first Sunday on or after March 1st.[...]

F-3 Daylight Savings Time on ProCurve Switches Before configuring a “User defined” Daylight Time Rule, it is important to understand how t he switch treats the entri es. The switch knows whi ch dates are Sundays, and uses an algorithm to determine on which date to change the system clock, given the configured “Beginning day” and “Ending d[...]

G-1 G Network Out-of-Band Management (OOBM) Contents Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-5 OOBM and Switch Applications . . . . . . . . . . . . . . . . . . . .[...]

G-2 Network Out-of-Band Management (OOBM) Concepts Concepts Management communications with a manage d switch can be either: ■ in band — through the network ed data ports of the switch or: ■ out of band — through a dedicated ma nagement port (or po rts) separate from the data ports Out-of-band ports have typical ly been serial console ports [...]

G-3 Network Out-of-Band Management (OOBM) Concepts Figure D-1. C-class enclosure OA Management port Out-of-band management (OOBM) operates on a “management plane” that is separate from the “data plane” used by data traffic on the switch and by in- band managem ent traffic. That separa tion means that out- of-band manage- ment can contin ue [...]

G-4 Network Out-of-Band Management (OOBM) Concepts Advantages allows centralized management not affected by events on data network, shows boot sequence not affected by events on data network; allows centralized management; allows improved security Disadvantages can be affected by events on data network; does not show boot sequence requires PC to di[...]

G-5 Network Out-of-Band Management (OOBM) Concepts Example In a typical data center installation, blade switches in a C-class enclosure connect servers to the data network, while the management port of the OA module in the C-class encl osure conn ects the switches to a physically and logically separate management network. This allows network admini[...]

G-6 Network Out-of-Band Management (OOBM) Concepts OOBM and Switch Applications The table below shows the switch appl ications that are supported on the OOBM interf ace as well as on the da ta inte rfaces. In this li st , some applications are client-only , some are server -only , and some are both. For applications that have servers, oobm/data/bot[...]

G-7 Network Out-of-Band Management (OOBM) Tasks Ta s k s OOBM Configuration OOBM context OOBM configurat ion commands can be issu ed from the global confi guration context ( config ) or from a specific OOBM configuratio n context ( oobm ). T o enter the OOBM configurat ion context from the general config uration con- text, use th e oobm command. Sy[...]

G-8 Network Out-of-Band Management (OOBM) Tasks OOBM enable/disable T o ena ble or disable network O OBM, use the enable or disable command. Network OOBM is enabled by default. Syntax: From the OOBM context: enable disable From the general configuration context: oobm enable oobm disable Enables or disables networked out-of-band-management on the sw[...]

G-9 Network Out-of-Band Management (OOBM) Tasks OOBM port enable/disable The OOBM interf ace command e nables or disables the OOBM interface (the OOBM port, as opposed to the OOBM function). Syntax: From the OOBM context: interface [enable | disable] From the general configuration context: oobm interface [enable | disable] Enables or disables the n[...]

G-10 Network Out-of-Band Management (OOBM) Tasks OOBM IPv4 address configuration Configuring an IPv4 add ress for the OOBM interface is simi lar to VLAN IP address configuratio n, but it is a ccomplished wit hin the OOBM context. OOBM IPv4 default gateway configuration Configuring an IPv4 defaul t gateway for the OOBM interf ace is similar to VL AN[...]

G-11 Network Out-of-Band Management (OOBM) Tasks OOBM Show Commands The show commands for OOBM are similar to the analogous commands for the data plane. Note that you must always include the oobm parameter to see the informati on for the OOBM inte rfac e, regardless of the context. For instance, even from the OOBM context the show ip command displa[...]

G-12 Network Out-of-Band Management (OOBM) Tasks Show OOBM IP configuration Use show oobm ip to se e the IP configuration of the OOBM interfac e. Show OOBM ARP information Use show oobm arp to see the ARP table entr ies for the OOBM interfa ce. Syntax: sho w oobm ip Summarizes the IP configuration of the OOBM interface. This command displays the st[...]

G-13 Network Out-of-Band Management (OOBM) Tasks Application Server Commands Application server s (as described in OOBM and Server Applications in the Concepts section above) have a dded a listen keyword with oobm|data|both options to specify which i nterface(s) is(are) active. Default value is both for all servers. For example: T elnet: telnet-ser[...]

G-14 Network Out-of-Band Management (OOBM) Tasks The show servers command shows the listen mode of the servers. ProCurve# show servers Server listen mode Server Listen mode ----------------------------- Telnet | both Ssh | both Tftp | both Web-management | both Snmp | both[...]

G-15 Network Out-of-Band Management (OOBM) Tasks Application Client Commands CLI commands for client applications have added t he oobm keyword to allow you to specify that the outgoing reques t be issued from t h e OOBM interface. If you do not spe cify the oobm keyword, the requ est will be issu ed from th e appropriate in-band data in terface. Co[...]

G-16 Network Out-of-Band Management (OOBM) Tasks Example This example shows setup and use of network OOBM using the commands described above. Assume that th e figure below describe s how you want to set up your data center . Figure D-3. Example data center Assume that you are config uring the switch in the left-hand rack to commu- nicate on both th[...]

G-17 Network Out-of-Band Management (OOBM) Tasks Switch 41# config Switch 41(config)# vlan 1 Switch 41(vlan-1)# ip address 10.1.129.7/20 Set up IP address on data network. Switch 41(vlan-1)# end Exit back to manager contex t . Switch 41# show oobm Look at default OO BM configuration. Global Configuration OOBM Enabled : Yes OOBM Port Type : 10/100TX[...]

Index – 1 Index Symbols => prompt …C - 7 7 Numerics 802.1X effect, LLDP … 13-76 LLDP blocked … 13-44 802.1X access control authentication fa ilure, SNMP notification … 13-27 SNMP notification of authentication failure … 13-27 A access manager … 13-14 operator … 13-14 out-of-band … 2-4 address network manager … 13-5 address ta[...]

2 – Index broadcast storm … 11-3, C-16 broadcast traffic IPX … 10-5, 10-19 RIP … 10-5, 10-19 browser interface See web browser interface. C CDP … 13-77, 13-78, 1 3-79, 13-80, 13-82 Classifier mirroring configuration … B-27 Clear + Reset button co mbination …6 - 3 7 Clear button …5 - 1 0 restoring factory default configuration … C-[...]

Index – 3 policy, override … 6-32 power cycle … 6-31 primary boot path … 6-29 reboot policy options … 6-26 reboot policy, override … 6 -30 reboot process … 6-27 reload … 6-32 rename config file … 6-33 reset … 6-31 running-config file … 6 -27 running-config fi le operation … 6-26 secondary boot path … 6-29 show config file [...]

4 – Index See also gate way. default settings auto-TFTP, disabled …A - 1 1 banner … 2-9, 2-13 baud rate, spee d sense …7 - 3 boot flash, primary …6 - 1 9 configuration file name, switch.cfg …6 - 4 2 console/serial configuration … 7-5 debug destination, disabled …C - 4 5 default gateway, none …8 - 2 DHCP Option 66, enabled …6 - 4[...]

Index – 5 server address, DHCP not used … C-86 server IP address … C-80, C-86 server-address co nfiguration … C-82 three entries supported … C-82 three server entries supported … C-82 traceroute … C-79, C-81, C-84 VLAN, best route selection … C-86 documentation feature matrix … -xxii latest versions … -xxi printed in-box publica[...]

6 – Index H Help for CLI … 1-7, 4-11 for menu interface … 1-6, 3-9, 3-11 for web browser interface … 1-7, 5-13 online, inoperable … 5-13 hop, router …8 - 1 0 HP Auto-MDIX feature … 10-19 web browser interface … 2 -6 I IDM resource usage … E-2 resources … E-3 IDS …B - 2 5 IEEE 802.1d …C - 1 6 IEEE P802.1AB/D9 … 13-42 IGMP h[...]

Index – 7 L LACP 802.1X not allowed … 11-22 active … 11-15 blocked ports … 11-23 CLI access … 11-11 default port operation … 11-21 described … 11-6, 11-18 Dyn1 … 11-7 dynamic … 11-19 enabling dynamic trunk … 11-15 full-duplex required … 11-4, 11-18 IGMP … 11-23 mirroring static trunk … B-28 no half-duplex … 11-25 operati[...]

8 – Index packet time-to-live … 13-42 packet-forwarding … 1 3-39, 13-75 packets not forwarded … 13-38 per-port counters … 13-74 port description … 13-53 port ID … 13-52 port speed … 13-54 port trunks … 13-43 port type … 13-52 refresh interval … 13-47 reinitialization delay … 13-49 remote management address … 13-42 remote m[...]

Index – 9 configuration, display … 10-21 operation … 10-19 port mode, display … 10-21 media type, port trunk … 11-3 memory flash … 3-10, 6-3 startup configuration … 3-10 menu inter face configuration changes, saving … 3-10 moving to or from the CLI … 4-7 See also console. mesh mirroring … B-23 MIB HP proprietary … 13-5 listing[...]

10 – Index using MAC addresses … B-26 VLAN … B-31 VLAN rule, exit port … B-47 VLAN tag, frame size … B-43 VLAN tagging … B-45 Web interface … B-28 Web limits … B-29 MLTS …1 3 - 3 8 module clearing the config … 10-29 CLI command … 10-29 configuring when not inserted … 10-29 pre-configuring … 10-29 remove configuration comma[...]

Index – 11 displaying resource usage … E-2 poll interval See TimeP. port address table … B-14 blocked by UDLD … 10-32 broadcast limit … 10-18 CLI access … 10-8 configuration … 10-1 configuring UDLD … 10-32 context level … 10-16 counters … B-11 counters, reset … B-11 duplex, view … 10-8 enabling UDLD … 10-33 fiber-optic …[...]

12 – Index ProCurve Manager security concerns when deleting public community … 13-6 starting web browser … 5-4 updating switch software … A-24 using Java-enabled browser … 5-5 ProCurve, HP, URL … 13-5 prompt, => …C - 7 7 PSAP … 13-38 PSE … 13-38 Public Safety An swering Point … 13-38 public SNMP community … 13-6, 13-14 Q Qo[...]

Index – 13 username and password … 5-8 web browser access, RADIUS … 5-8 Self Test LED behavior during factory default reset … C-77 serial number …B - 6 setmib, delay interval … 13-48 setmib, reinit delay … 13-50 setup screen …1 - 8 severity level event log … C-24 selecting Event Log messages for debugging … C-53 SHA authenticati[...]

14 – Index selecting … 9-3 server priority … 9-14 show management … 9-9 unicast mode … 9-3, 9-11 unicast time polling … 9-25 unicast, deleting addresses … 9-26 unicast, replacing servers … 9-26 viewing … 9-4, 9-8 software See switch software. software image See switch software. software version …B - 6 sorting alert log entries ?[...]

Index – 15 task monitor …B - 8 taskusage -d …B - 8 taskUsageShow …B - 8 Telnet connecting to switch … 3-4 enable/disable … 7-4 outbound … 7-6 terminate session, kill command … 7-11 troubleshooting access … C-8 telnet domain name address … 7-6 hostname … 7-6 ipv6 address … 7-6 show command … 7-6 switch-num … 7-6 terminal [...]

16 – Index approaches … C-5 browsing the configuration file … C-65 configuring debug destinations … C-38 console access problems … C-7 diagnosing unusual networ k activity … C-9 diagnostics tools … C-56 displaying switch operation … C-65, C-68 DNS See DNS. fast-uplink … C-16 ping and link tests … C-57 resource usage … E-2 rest[...]

Index – 17 ID … 4-15 IP addres sing with multiple … 8-4 jumbo max frame si ze … 12-7 link blocke d … C-16 MAC address … D-2, D-5 mana gement and ju mbo fra mes … 12 -9 managem ent VLAN, r esourc e usag e … E-2 mana gement VLAN, SNMP block … 13-3 mirroring … B-3, B-23 multinet … 8 -3 multinetting … 8-3, 8 -8 multiple … 13- [...]

ProCurve 5400zl Switches Installation and *5992-5523* T echnology for bet ter business outcomes T o learn mo re , vi sit w w w .hp.com/go/bladesy stem/ documentation/ © Cop yri ght 2009 Hewle tt-P ack ard De velopment C ompan y , L.P . The inf ormati on contained here in is subject to change w ithout notice . The only warr anties for HP products a[...]